HEF4794BT,118 [NXP]
HEF4794B - 8-stage shift-and-store register LED driver SOP 16-Pin;
| 型号： | HEF4794BT,118 |
| 厂家： | 
NXP |
| 描述： | HEF4794B - 8-stage shift-and-store register LED driver SOP 16-Pin |
| 文件： | 总17页 (文件大小：141K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HEF4794B
8-stage shift-and-store register LED driver
Rev. 04 — 22 December 2009
Product data sheet
1. General description
The HEF4794B is an 8-stage serial shift register. It has a storage latch associated with
each stage for strobing data from the serial input (D) to the parallel LED driver outputs
(QP0 to QP7). Data is shifted on the positive-going clock (CP) transitions. The data in
each shift register stage is transferred to the storage register when the strobe input (STR)
is HIGH. Data in the storage register appears at the outputs whenever the output enable
input (OE) signal is HIGH.
Two serial outputs (QS1 and QS2) are available for cascading a number of HEF4794B
devices. Serial data is available at QS1 on positive-going clock edges to allow high-speed
operation in cascaded systems with a fast clock rise time. The same serial data is
available at QS2 on the next negative going clock edge. This is used for cascading
HEF4794B devices when the clock has a slow rise time.
It operates over a recommended VDD power supply range of 3 V to 15 V referenced to VSS
(usually ground). Unused inputs must be connected to VDD, VSS, or another input. It is
also suitable for use over both the industrial (−40 °C to +85 °C) and automotive (−40 °C to
+125 °C) temperature ranges.
2. Features
Fully static operation
5 V, 10 V, and 15 V parametric ratings
Standardized symmetrical output characteristics
Operates across the automotive temperature range −40 °C to +125 °C
Complies with JEDEC standard JESD 13-B
3. Applications
Automotive and industrial
4. Ordering information
Table 1.
Ordering information
All types operate from −40 °C to +125 °C.
Type number
Package
Name
Description
Version
HEF4794BP
HEF4794BT
DIP16
SO16
plastic dual in-line package; 16 leads (300 mil)
plastic small outline package; 16 leads; body width 3.9 mm
SOT38-4
SOT109-1
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
5. Functional diagram
3
1
CP
STR
QS1
QS2
QP0
QP1
QP2
9
10
4
2
D
10
9
8-STAGE SHIFT
REGISTER
QS2
QS1
3
5
CP
6
2
D
1
QP3
QP4
QP5
QP6
QP7
7
8-BIT STORAGE
REGISTER
STR
OE
14
13
12
11
15
OPEN-DRAIN
OUTPUTS
4
5
6
7
14 13 12 11
QP4 QP6
OE
15
QP0
QP2
QP1
QP3
QP5
QP7
001aaf111
001aag798
Fig 1. Logic symbol
Fig 2. Functional diagram
STAGE 0
STAGES 1 TO 6
STAGE 7
D
D
Q
D
Q
D
Q
QS1
CP
CP
D
Q
QS2
FF 0
FF 7
CP
CP
CP
LATCH
D
Q
D
Q
CP
CP
LATCH 0
LATCH 7
STR
OE
001aag799
QP0
QP2
QP4
QP6
QP1
QP3
QP5
QP7
Fig 3. Logic diagram
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
2 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
6. Pinning information
6.1 Pinning
HEF4794B
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
STR
D
V
DD
OE
CP
QP4
QP5
QP6
QP7
QS2
QS1
QP0
QP1
QP2
QP3
V
SS
001aag800
Fig 4. Pin configuration
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
3 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
6.2 Pin description
Table 2.
Symbol
D
Pin description
Pin
Description
serial input
2
QP0 to QP7
QS1
4, 5, 6, 7, 14, 13, 12, 11
parallel output
serial output
serial output
clock input
9
QS2
10
3
CP
STR
1
strobe input
OE
15
16
8
output enable input
supply voltage
ground (0 V)
VDD
VSS
7. Functional description
Table 3.
Function table[1]
Input
Parallel output
Serial output
QS1[2]
Q6S
CP
↑
OE
L
STR
X
D
X
X
X
L
QP0
QPn
QS2[3]
Z
Z
no change
Q7S
↓
L
X
Z
Z
n.c.
↑
H
H
H
H
L
no change
no change
QPn−1
QPn−1
no change
Q6S
no change
no change
no change
Q7S
↑
H
Z
Q6S
↑
H
H
H
L
Q6S
↓
H
no change
no change
[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state;
↑ = LOW-to-HIGH clock transition; ↓ = HIGH-to-LOW clock transition.
[2] Q6S = the data in register stage 6 before the LOW to HIGH clock transition.
[3] Q7S = the data in register stage 7 before the HIGH to LOW clock transition.
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
4 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
clock input
data input
strobe input
output enable
input
internal Q0S
(FF0)
Z-state
QP0 output
internal Q6S
(FF6)
Z-state
QP6 output
serial QS1
output
serial QS2
output
001aag801
Fig 5. Timing diagram
8. Limiting values
Table 4.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
VDD
IIK
Parameter
Conditions
Min
−0.5
-
Max
Unit
V
supply voltage
+18
input clamping current
input voltage
VI < −0.5 V or VI > VDD + 0.5 V
±10
mA
V
VI
−0.5
-
VDD + 0.5
±10
IOK
output clamping current
QSn outputs;
mA
VO < −0.5 V or VO > VDD + 0.5 V
QPn outputs; VO < −0.5 V
-
40
±10
±10
40
mA
mA
mA
mA
°C
II
input current
-
IO
output current
QSn outputs
QPn outputs
-
-
Tstg
Tamb
Ptot
storage temperature
ambient temperature
total power dissipation
−65
−40
+150
+125
°C
Tamb = −40 °C to +125 °C
DIP16 package
[1]
[2]
-
-
-
750
500
100
mW
mW
mW
SO16 package
P
power dissipation
[1] For DIP16 package: Ptot derates linearly with 12 mW/K above 70 °C.
[2] For SO16 package: Ptot derates linearly with 8 mW/K above 70 °C.
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
5 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
9. Recommended operating conditions
Table 5.
Symbol
VDD
Recommended operating conditions
Parameter
Conditions
Min
Max
15
Unit
V
supply voltage
3
VI
input voltage
0
VDD
+125
3.75
0.5
V
Tamb
ambient temperature
input transition rise and fall rate
in free air
−40
°C
Δt/ΔV
VDD = 5 V
VDD = 10 V
VDD = 15 V
-
-
-
μs/V
μs/V
μs/V
0.08
10. Static characteristics
Table 6.
Static characteristics
VSS = 0 V; VI = VSS or VDD; unless otherwise specified.
Symbol Parameter
Conditions
VDD
Tamb = −40 °C Tamb = 25 °C Tamb = 85 °C Tamb = 125 °C Unit
Min
Max
-
Min
Max
-
Min
Max
-
Min
Max
-
VIH
HIGH-level
input voltage
|IO| < 1 μA
5 V
10 V
15 V
5 V
3.5
3.5
3.5
3.5
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
7.0
-
7.0
-
7.0
-
7.0
-
11.0
-
11.0
-
11.0
-
11.0
-
VIL
LOW-level
input voltage
|IO| < 1 μA
-
1.5
3.0
4.0
-
-
1.5
3.0
4.0
-
-
1.5
3.0
4.0
-
-
1.5
3.0
4.0
-
10 V
15 V
5 V
-
-
-
-
-
-
-
-
VOH
HIGH-level
output voltage |IO| < 1 μA
QSn outputs;
4.95
4.95
4.95
4.95
10 V
15 V
5 V
9.95
-
9.95
-
9.95
-
9.95
-
14.95
-
14.95
-
14.95
-
14.95
-
VOL
LOW-level
output voltage |IO| < 1 μA
QSn outputs;
-
-
-
-
-
-
0.05
0.05
0.05
0.75
0.75
0.75
-
-
-
-
-
-
0.05
0.05
0.05
0.75
0.75
0.75
-
-
-
-
-
-
0.05
0.05
0.05
1.5
1.5
1.5
-
-
-
-
-
-
0.05
0.05
0.05
1.5
1.5
1.5
10 V
15 V
5 V
QP outputs;
|IO| < 20 mA
10 V
15 V
IOH
HIGH-level
output current
QSn outputs
VO = 2.5 V
VO = 4.6 V
VO = 9.5 V
5 V
5 V
−1.7
−0.64
−1.6
-
-
-
-
−1.4
−0.5
−1.3
−3.4
-
-
-
-
−1.1
−0.36
−0.9
-
-
-
-
−1.1
−0.36
−0.9
-
-
-
-
mA
mA
mA
mA
10 V
VO = 13.5 V 15 V
QSn outputs
−4.2
−2.4
−2.4
IOL
LOW-level
output current
VO = 0.4 V
VO = 0.5 V
VO = 1.5 V
5 V
10 V
15 V
15 V
0.64
1.6
4.2
-
-
0.5
1.3
3.4
-
-
0.36
0.9
2.4
-
-
0.36
0.9
2.4
-
-
-
-
mA
mA
mA
-
-
-
-
-
-
II
input leakage
current
±0.1
±0.1
±1.0
±1.0 μA
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
6 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
Table 6.
Static characteristics …continued
VSS = 0 V; VI = VSS or VDD; unless otherwise specified.
Symbol Parameter
Conditions
VDD
Tamb = −40 °C Tamb = 25 °C Tamb = 85 °C Tamb = 125 °C Unit
Min
Max
2
Min
Max
2
Min
Max
15
Min
Max
15
IOZ
IDD
CI
OFF-state
output current is HIGH;
VO = 15 V
QPn output
5 V
10 V
15 V
5 V
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
μA
μA
μA
2
2
-
15
15
2
2
-
15
15
supply current IO = 0 A
5
5
-
-
150
300
600
-
150 μA
300 μA
600 μA
10 V
15 V
-
10
20
-
10
20
-
-
input
7.5
-
-
capacitance
11. Dynamic characteristics
Table 7.
Dynamic characteristics
VSS = 0 V; Tamb = 25 °C unless otherwise specified. For test circuit, see Figure 10.
Symbol Parameter
Conditions
VDD
5 V
Extrapolation formula
Min
Typ
Max
320
130
90
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
[1]
tPHL
tPLH
tPZL
tPLZ
HIGH to LOW
propagation delay
CP to QS1;
see Figure 6
132 ns + (0.55 ns/pF)CL
53 ns + (0.23 ns/pF)CL
37 ns + (0.16 ns/pF)CL
92 ns + (0.55 ns/pF)CL
39 ns + (0.23 ns/pF)CL
32 ns + (0.16 ns/pF)CL
102 ns + (0.55 ns/pF)CL
44 ns + (0.23 ns/pF)CL
32 ns + (0.16 ns/pF)CL
102 ns + (0.55 ns/pF)CL
49 ns + (0.23 ns/pF)CL
37 ns + (0.16 ns/pF)CL
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
160
65
10 V
15 V
5 V
45
CP to QS2;
see Figure 6
120
50
240
100
80
10 V
15 V
5 V
40
[1]
LOW to HIGH
propagation delay
CP to QS1;
see Figure 6
130
55
260
110
80
10 V
15 V
5 V
40
CP to QS2;
see Figure 6
130
60
260
120
90
10 V
15 V
5 V
45
OFF-state to LOW
propagation delay
CP to QPn;
see Figure 6
240
80
480
160
110
280
140
110
340
150
120
200
100
70
10 V
15 V
5 V
55
STR to QPn;
see Figure 7
140
70
10 V
15 V
5 V
55
LOW to OFF-state
propagation delay
CP to QPn;
see Figure 6
170
75
10 V
15 V
5 V
60
STR to QPn;
see Figure 7
100
40
10 V
15 V
35
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
7 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
Table 7.
Dynamic characteristics …continued
VSS = 0 V; Tamb = 25 °C unless otherwise specified. For test circuit, see Figure 10.
Symbol Parameter
Conditions
VDD
5 V
Extrapolation formula
Min
-
Typ
100
55
50
80
40
30
85
40
30
30
15
12
40
30
12
30
10
5
Max
Unit
ns
[2]
[2]
ten
tdis
tt
enable time
disable time
transition time
pulse width
OE to QPn;
see Figure 8
200
10 V
15 V
5 V
-
110
ns
-
100
ns
OE to QPn;
see Figure 8
-
160
ns
10 V
15 V
5 V
-
80
ns
-
60
ns
[1]
[3]
QS1, QS2;
see Figure 6
35 ns + (1.00 ns/pF)CL
19 ns + (0.42 ns/pF)CL
16 ns + (0.28 ns/pF)CL
-
170
ns
10 V
15 V
5 V
-
80
ns
-
60
ns
tW
CP; LOW and
HIGH;
see Figure 6
60
30
24
80
60
24
60
20
15
+5
20
20
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ns
10 V
15 V
5 V
ns
ns
STR; HIGH;
see Figure 7
ns
10 V
15 V
5 V
ns
ns
tsu
set-up time
hold time
D to CP;
see Figure 9
ns
10 V
15 V
5 V
ns
ns
th
D to CP;
see Figure 9
−15
5
ns
10 V
15 V
5 V
ns
5
ns
fclk(max)
maximum clock
frequency
CP; see Figure 6
10
22
28
MHz
MHz
MHz
10 V
15 V
11
14
[1] The typical values of the propagation delay and transition times are calculated from the extrapolation formulas shown (CL in pF).
[2] ten is the same as tPZL and tdis is the same as tPLZ
[3] tt is the same as tTLH and tTHL
Table 8.
Dynamic power dissipation
PD can be calculated from the formulas shown. VSS = 0 V; tr = tf ≤ 20 ns; Tamb = 25 °C.
Symbol Parameter
VDD
Typical formula
Where
PD
dynamic power dissipation 5 V
PD = 1200 × fi + Σ(fo × CL) × VDD2 μW
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
Σ(fo × CL) = sum of the outputs;
10 V PD = 5550 × fi + Σ(fo × CL) × VDD2 μW
15 V PD = 15000 × fi + Σ(fo × CL) × VDD2 μW
VDD = supply voltage in V.
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
8 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
12. Waveforms
1/f
clk(max)
V
I
V
CP input
M
t
V
SS
t
t
W
W
t
PLZ
PZL
V
DD
V
Y
QPn output
QS1 output
V
X
V
OL
t
t
PLH
PHL
V
OH
90 %
V
M
10 %
V
OL
t
t
THL
TLH
t
t
PHL
PLH
V
OH
90 %
V
QS2 output
M
10 %
TLH
V
OL
t
t
THL
001aag222
Parallel output measurement points are given in Table 9.
VOL and VOH are typical output voltage levels that occur with the output load.
Fig 6. Propagation delay clock (CP) to output (QPn, QS1, QS2), clock pulse width and maximum clock
frequency
Table 9.
Supply
VDD
Measurement points
Input
VM
Output
VM
VX
VY
5 V to 15 V
0.5VDD
0.5VDD
0.1VO
0.9VO
V
I
V
M
CP input
V
V
SS
V
I
STR input
V
M
SS
t
W
t
t
PZL
PLZ
V
DD
V
Y
QPn output
V
X
V
OL
001aag802
Measurement points are given in Table 9.
VOL is the typical output voltage level that occurs with the output load.
Fig 7. Strobe (STR) to output (QPn) propagation delays and the strobe pulse width
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
9 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
V
I
OE input
V
M
V
SS
t
t
PZL
PLZ
V
DD
V
Y
output
LOW to OFF-state
OFF-state to LOW
V
X
V
OL
outputs
enabled
outputs
disabled
outputs
enabled
001aag803
Measurement points are given in Table 9.
VOL is the typical output voltage level that occurs with the output load.
Fig 8. Enable and disable times for input OE
V
I
CP input
V
M
V
V
SS
t
t
su
su
t
h
t
h
V
I
V
M
D input
SS
DD
V
QPn output
V
OL
001aag805
Measurement points are given in Table 9.
The shaded areas indicate when the input is permitted to change for predictable output performance.
VOL is the typical output voltage level that occurs with the output load.
Fig 9. Set-up and hold times for the data input (D)
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
10 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
V
I
90 %
input pulse
10 %
V
SS
t
r
t
f
V
EXT
V
DD
R
L
V
I
V
O
G
DUT
C
R
L
T
001aag804
Test data is given in Table 10.
Definitions for test circuit:
DUT - Device Under Test.
RL = Load resistance.
CL = load capacitance.
RT = Termination resistance should be equal to output impedance of Zo of the pulse generator.
VEXT = External voltage for measuring switching times.
Fig 10. Test circuit for measuring switching times
Table 10. Test data
Supply
VDD
Input
VI
VEXT
Load
CL
tr, tf
tPLZ, tPZL
VDD
tPLH, tPHL
RL
5 V to 15 V
VDD
≤ 20 ns
open
50 pF
1 kΩ
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
11 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
13. Application information
Application example: serial-to-parallel data converting LED drivers.
V
DD
V
CC
QP0
OE
QP7
S2
QP0
OE
QP7
S2
D
D
HEF4794B
HEF4794B
STR
CP
STR
CP
PWM
dimmer input
CONTROL
AND
SYNC
CIRCUITRY
001aag806
data clock
from remote
control panel
Fig 11. Serial-to-parallel converting LED drivers
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
12 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
14. Package outline
DIP16: plastic dual in-line package; 16 leads (300 mil)
SOT38-4
D
M
E
A
2
A
A
1
L
c
e
w M
Z
b
1
(e )
1
b
b
2
16
9
M
H
pin 1 index
E
1
8
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
(1)
A
A
A
2
(1)
(1)
Z
1
w
UNIT
mm
b
b
b
c
D
E
e
e
L
M
M
H
1
2
1
E
max.
min.
max.
max.
1.73
1.30
0.53
0.38
1.25
0.85
0.36
0.23
19.50
18.55
6.48
6.20
3.60
3.05
8.25
7.80
10.0
8.3
4.2
0.51
3.2
2.54
0.1
7.62
0.3
0.254
0.01
0.76
0.068 0.021 0.049 0.014
0.051 0.015 0.033 0.009
0.77
0.73
0.26
0.24
0.14
0.12
0.32
0.31
0.39
0.33
inches
0.17
0.02
0.13
0.03
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
95-01-14
03-02-13
SOT38-4
Fig 12. Package outline SOT38-4 (DIP16)
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
13 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
SO16: plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1
D
E
A
X
v
c
y
H
M
A
E
Z
16
9
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
8
e
w
M
detail X
b
p
0
2.5
scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
Z
θ
1
2
3
p
E
max.
0.25
0.10
1.45
1.25
0.49
0.36
0.25
0.19
10.0
9.8
4.0
3.8
6.2
5.8
1.0
0.4
0.7
0.6
0.7
0.3
mm
1.27
0.05
1.05
0.041
1.75
0.25
0.01
0.25
0.01
0.25
0.1
8o
0o
0.010 0.057
0.004 0.049
0.019 0.0100 0.39
0.014 0.0075 0.38
0.16
0.15
0.244
0.228
0.039 0.028
0.016 0.020
0.028
0.012
inches
0.069
0.01 0.004
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-19
SOT109-1
076E07
MS-012
Fig 13. Package outline SOT109-1 (SO16)
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
14 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
15. Revision history
Table 11. Revision history
Document ID
HEF4794B_4
Modifications:
Release date
20091222
Data sheet status
Change notice
Supersedes
Product data sheet
-
HEF4794B_3
• Section 2 “Features” ESD data removed.
• Section 8 “Limiting values” IIK values updated.
• Section 8 “Limiting values” IOK values updated.
• Section 9 “Recommended operating conditions” Δt/ΔV values updated.
• Abbreviations section removed.
HEF4794B_3
HEF4794B_2
HEF4794B_1
20080812
19990630
19940701
Product data sheet
Product specification
Product specification
-
-
-
HEF4794B_2
HEF4794B_1
-
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
15 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
malfunction of an NXP Semiconductors product can reasonably be expected
16.2 Definitions
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
16.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
HEF4794B_4
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 22 December 2009
16 of 17
HEF4794B
NXP Semiconductors
8-stage shift-and-store register LED driver
18. Contents
1
2
3
4
5
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information. . . . . . . . . . . . . . . . . . . . . 1
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
7
Functional description . . . . . . . . . . . . . . . . . . . 4
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5
Recommended operating conditions. . . . . . . . 6
Static characteristics. . . . . . . . . . . . . . . . . . . . . 6
Dynamic characteristics . . . . . . . . . . . . . . . . . . 7
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Application information. . . . . . . . . . . . . . . . . . 12
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 13
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 15
8
9
10
11
12
13
14
15
16
Legal information. . . . . . . . . . . . . . . . . . . . . . . 16
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 16
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
16.1
16.2
16.3
16.4
17
18
Contact information. . . . . . . . . . . . . . . . . . . . . 16
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2009.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 22 December 2009
Document identifier: HEF4794B_4
相关型号：
HEF4794BT-T
IC LED DISPLAY DRIVER, DSO16, 3.90 MM, PLASTIC, MS-012, SOT109-1, SOP-16, Display Driver
NXP
©2020 ICPDF网 联系我们和版权申明