HTRC11001T/03EE [NXP]
HITAG reader chip; HITAG阅读器芯片型号: | HTRC11001T/03EE |
厂家: | NXP |
描述: | HITAG reader chip |
文件: | 总22页 (文件大小:184K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HTRC110
HITAG reader chip
Rev. 3.1 — 9 February 2010
037031
Product data sheet
PUBLIC
1. General description
The HITAG Reader Chip HTRC110 is intended for use with transponders, which are
based on NXP Semiconductors based HITAG transponder ICs.
In addition the IC supports other 125 kHz transponder types using amplitude modulation
for the write operation and AM/PM for the read operation. The receiver parameters (gain
factors, filter cutoff frequencies) can be optimized to system and transponder
requirements. The HTRC110 is designed for easy integration into RF-identification
readers. State-of-the-art technology allows almost complete integration of the necessary
building blocks. A powerful antenna driver/modulator together with a low-noise adaptive
sampling time demodulator, programmable filters/amplifier and digitizer build the complete
transceiver unit, required to design high-performance readers. A three-pin microcontroller
interface is employed for programming the HTRC110 as well as for the bidirectional
communication with the transponders. The three-wire interface can be changed into a
two-wire interface by connecting the data input and the data output.
Tolerance dependent zero amplitude modulation caused severe problems in envelope
detector systems, resulting in the need of very low tolerance reader antennas. These
problems are solved by the Adaptive Sampling Time technique (AST).
2. Features and benefits
Optimized for HITAG transponder ICs
Robust antenna coil power driver stage with modulator
High performance adaptive sampling time AM/PM demodulator (patent pending)
Read and write function
On-chip clock oscillator
Antenna rupture and short circuit detection
Low power consumption
Very low power stand-by mode
Low external component count
Small package (SO14)
3. Applications
Livestock tracking
Industrial applications
Logistics
HTRC110
NXP Semiconductors
HITAG reader chip
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
HTRC11001T/02EE SO14
HTRC11001T/03EE SO14
plastic small outline package; 14 leads; body width 3.9 mm, tube
plastic small outline package; 14 leads; body width 3.9 mm, reel
SOT108-1
SOT108-1
5. Block diagram
Fig 1. Block diagram HTRC110
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
2 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
6. Pinning information
6.1 Pinning
Fig 2. Pin configuration
6.2 Pin description
Table 2.
Symbol
VSS
Pin description
Pin
1
Description
GND, negative supply input
coil driver output
TX2
2
VDD
3
stabilized 5 V supply input
coil driver output
TX1
4
MODE
XTAL1
XTAL2
SCLK
DIN
5
to enable filtering of SCLK and DIN (for active antenna applications)
oscillator interface, input
6
7
oscillator interface, output
8
microcontroller interface: serial clock input
microcontroller interface: serial data in
microcontroller interface: serial data out
not connected
9
DOUT
n.c.
10
11
12
13
14
CEXT
QGND
RX
high pass filter coupling
analog ground bias
demodulator input
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
3 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
7. Key data
Supply VDD:
5 V ± 10%
Clock/Osc. frequency:
4,8,12,16 MHz programmable
(antenna carrier frequency 125 kHz)
200 mAp continuous
CMOS compatible
SO14
Antenna driver current:
Serial interface:
Package:
Operation temperature range:
−40 °C to +85°C
8. Minimum application circuitry
The following figure shows a minimal application circuitry for the HTRC110. The reader
coil La together with the capacitor Ca forms a series resonant LC circuit (f = 125 kHz). The
high voltages in the LC circuit are divided to safe operating levels by Rv and the chip
internal resistor Rdem_in behind the RX-pin. The two capacitors connected to XTAL1 and
XTAL2 shall be the recommended values and types from the crystal's data sheet.
Alternatively to a crystal a ceramic resonator can be used or an external clock source can
be connected to XTAL1.
Fig 3. Minimum application circuitry
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
4 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
9. Functional description
9.1 Power supply
The HTRC110 works with an external 5 V± 10 % power supply at VDD. The maximum
DC-current is 10 mA+Îant*2/ π = 137 mA. For optimum performance, the power supply
connection should be by-passed to ground with a 100 nF capacitor close to the IC.
9.2 Antenna driver, data input
The drivers deliver a square shaped voltage to the series resonant antenna circuit. Due to
the full bridge configuration of the drivers this voltage Udrvpp is approximately 10 V
(peak-peak) corresponding to Ûdrv = 5 V. The current flowing through the antenna is sine
shaped. It´s amplitude is approximately:
9.3 Diagnosis
In order to detect an antenna short or open condition the antenna tap voltage is
monitored. An antenna fail condition is reported in the status bit ANTFAIL (see Table 16),
if the antenna tap voltage does not go more negative than the diagnosis level DLEV (see
Table 18). This condition is checked for every coil driver cycle.
9.4 Oscillator/programmable divider/clock
The crystal oscillator at XTAL1/2 works with either crystal or ceramic resonators. It
delivers the input clock frequency of 4, 8, 12 or 16 MHz. The oscillator frequency is
divided by a programmable divider to obtain the carrier frequency of 125 kHz (see
Table 12). Alternatively, an external clock signal (CMOS compatible) may be fed into the
IC via XTAL1. For example, this signal can be derived from the microcontroller clock.
9.5 Adaptive sampling time demodulator
The demodulator senses the absorption modulation applied by a transponder when
inserted into the field. The signal is picked up at the antenna tap point between La and Ca.
It is divided by Rv and the internal resistor Rdem_in to a level below 8 V (peak) with respect
to QGND at the RX-pin (see Figure 3). Internally the signal is filtered with a second order
low pass filter.
The antenna current and therefore the tap voltage is modulated by the transponder in
amplitude and/or phase. This signal is fed into a synchronous demodulator recovering the
baseband signal. The amplification and the bandpass filter edge frequencies of the
demodulator can be adapted to different transponders via settings in the configuration
pages.
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
5 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
The phase between the driver excitation signal and the antenna tap voltage depends on
the antenna tuning. With optimum tuning, the phase of the antenna tap voltage is 90
degrees off the antenna driver signal. Detuning of the antenna resonant circuit results in a
change of this phase relationship.
The HTRC110's built-in phase measurement unit allows the measurement of this phase
relationship with a resolution of 360°/64 = 5.625°. This can be used to compute a
sampling time that compensates the mistuning of the reader antenna. The phase
measurement procedure can be carried out:
• either once before the first communication starts, if the position of the transponder
does not change with the respect to the reader antenna
• or during the communication (after sending the write pulses and before receiving the
answer of the transponder), if the tag is moving.
Before the system is switched into WRITE_TAG-mode, the demodulator has to be frozen.
This is internally done by clamping the input of the amplifier/filter unit to QGND. Doing so
avoids large transients in the amplifier and the digitizer, which could affect settling times.
In addition to the clamping, there exist other means in the HTRC110, which allow further
reduction of the settling times. All the parts of the circuitry, which are associated with these
functions, are controlled by the FREEZE0, FREEZE1 and THRESET bits, which are
located in configuration page 2.
For more details concerning WRITE Timing, Demodulator Setting, Power Up Sequence,
etc. please refer to the HTRC110 application note (Ref. 1).
9.6 Idle and power-down mode
The HTRC110 can be switched into idle mode via setting the PD-bit and resetting the
PD_MODE-bit. In this idle mode, only the oscillator and a few other system components
are active.
It is also possible to switch the IC completely off. This is achieved by the power-down
mode (PD = 1, PD_MODE = 1). Within this mode also the clock oscillator is switched off.
This reduces the supply current of the HTRC110 to less than 20 μA.
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
6 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
9.7 Serial interface
The communication between the HTRC110 and the microcontroller is done via a three
wire digital interface. The interface is operated by the following signals:
SCLK
DIN
DOUT
clock
data input
data output
SCLK and DIN are realized as Schmitt-Trigger inputs. DOUT is an open drain output with
internal pull-up resistor.
Every communication between HTRC110 and microcontroller begins with an initialization
of the serial interface. The interface initialization condition is a low-to-high transition of the
signal DIN while SCLK is high.
Fig 4. Serial signaling
All commands are transmitted to the HTRC110 serial interface starting with Most
Significant Bit (MSB). DIN and DOUT are valid when SCLK is high.
9.8 Glitch filter for increased noise/interference immunity
Connecting pin 5 (MODE) to VDD enables digital filtering of the SCLK and the DIN input
signals. This mode offers improved immunity against glitches on these interface signals. It
is intended to be used in the so called "Active Antenna Applications" where the
microcontroller and the reader communicate via long signal lines (e.g. 1 meter).
In other applications pin 5 (MODE) has to be connected to GND.
Please refer to the HTRC110 application note (Ref. 1) for a detailed description of this
feature.
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
7 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
10. Commands
Table 3 depicts the HTRC110 command set summary.
HTRC110 commands
Table 3.
Bit No.
7
6
5
4
3
2
1
0
Remark
Command name
GET_SAMPLING_TIME
GET_CONFIG_PAGE
READ_PHASE
MSB
LSB
0
0
0
0
1
0
0
0
0
1
0
0
0
0
1
0
0
0
0
-
0
0
1
8 bit resp. (0 0 D5-D0)
8 bit resp. (X3-X0 D3-D0)
8 bit resp. (0 0 D5 - D0)
READ_TAG-mode
0
1
P1
0
P0
0
1
0
READ_TAG
-
-
-
-
WRITE_TAG_N
1
N3
N2
N0
N0
WRITE_TAG-mode with
pulse width programming
WRITE_TAG
1
0
1
1
1
0
0
-
-
-
-
-
WRITE_TAG-mode
SET_CONFIG_PAGE
SET_SAMPLING_TIME
P1
D5
P0
D4
D3
D3
D2
D2
D0
D0
D0
D0
4*4 config bits available
10.1 READ_TAG
This command is used to read the demodulated bit stream from a transponder: After the
assertion of the three command bits the HTRC110 instantaneously switches to
READ_TAG-mode and transmits the demodulated, filtered and digitized data from the
transponder. Data comes out and should be decoded by the microcontroller.
READ_TAG-mode is terminated by a low to high transition at SCLK.
Table 4.
Bit No.
READ_TAG command
7
6
5
4
3
2
1
0
Remark
Command
1
1
1
-
-
-
-
-
received data available at DOUT
10.2 WRITE_TAG_N
This command is used to write data to a transponder.
If N3 to N0 are set to zero, the signal from DIN is transparently switched to the drivers. A
high level at DIN corresponds to antenna drivers witched off, a low level corresponds to
antenna drivers switched on.
If any binary number between 1 and 1111 is loaded into N3 to N0 the drivers are switched
off at the next positive transition of DIN. This state is held for a time interval equal to N * T0
(T0 = 8 μs). This method relaxes the timing resolution requirements to the microcontroller
and to the software implementation while providing exact, selectable write pulse timing.
WRITE_TAG-mode is terminated immediately by a low to high transition at SCLK.
Table 5.
Bit No.
READ_TAG_N command
7
6
5
4
3
2
1
0
Remark
Command
0
0
0
1
N3
N2
N1
N0
no response
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
8 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
10.3 WRITE_TAG
This is the 3 bit short form of the previously described command WRITE_TAG_N. It allows
to switch into WRITE_TAG-mode with a minimum communication time.
The behaviour of the WRITE_TAG command is identical to WRITE_TAG_N with two
exceptions:
• WRITE_TAG-mode is entered after assertion of the 3rd command bit.
• No N parameter is specified with this command; instead the N value, which was
programmed with the most recent WRITE_TAG_N command, is used. If no
WRITE_TAG_N was issued so far, a default N = 0 (transparent mode) will be
assumed.
Table 6.
Bit No.
WRTIE_TAG command
7
6
5
4
3
2
1
0
Remark
Command
1
1
0
-
-
-
-
-
no response
10.4 READ_PHASE
This command is used to read the antenna´s phase, which is measured at every carrier
cycle. The phase is coded binary in D5 to D0.
Table 7.
Bit No.
READ_PHASE command
7
0
0
6
0
0
5
4
3
2
1
0
Remark
Command
Response
0
0
1
0
0
0
-
-
D5
D4
D3
D2
D1
D0
10.5 SET_SAMPLING_TIME
This command specifies the demodulator sampling time ts. The sampling time is coded
binary in D5 to D0.
Table 8.
Bit No.
SET_SAMPLING_TIME command
7
6
5
4
3
2
1
0
Remark
Command
1
0
D5
D4
D3
D2
D1
D0
no response
10.6 GET_SAMPLING_TIME
This command is used to read back the sampling time ts set with SET_SAMPLING_TIME.
The sampling time is coded binary in D5 to D0.
Table 9.
Bit No.
GET_SAMPLING_TIME command
7
0
0
6
0
0
5
4
3
2
1
0
Remark
Command
Response
0
0
0
0
1
0
-
-
D5
D4
D3
D2
D1
D0
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
9 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
10.7 SET_CONFIG_PAGE
This command is used to set the amplifier and filter parameters (cutoff frequencies, gain
factors) and the different operation modes. P1 and P0 select one of four configuration
pages.
Table 10. SET_CONFIG_PAGE command
Bit No.
7
6
5
4
3
2
1
0
Remark
Command
0
1
P1
P0
D3
D2
01
D0
no response
Table 11. Config pages
Bit No.
P1
P0
D3
D2
D1
D0
Command/Page no.
SET_CONFIG_PAGE 0
SET_CONFIG_PAGE 1
SET_CONFIG_PAGE 2
SET_CONFIG_PAGE 3
0
0
1
1
0
1
0
1
GAIN1
GAIN0
PD
FILTERH
FILTERL
PD_MODE
THRESET
DIPSL1
HYSTERESIS TXDIS
ACQAMP
FREEZE1
FREEZ0
FSEL0
DISSMART- FSEL1
COMP
Table 12. Bit initial conditions
Bit name
FILTERL
FILTERH
Description
Initial
condition
main low pass cutoff frequency
main high pass cutoff frequency
0
0: fL = 3 kHz
1: fL = 6 kHz
0
0: fH = 40 Hz
1: fH = 160 Hz
GAIN0
GAIN1
TXDIS
amplifier_0 gain factor
amplifier_1 gain factor
disable coil driver
0
1
0
0: gain0 = 16; 1: gain0 = 32
0: gain1 = 6.22; 1: gain1 = 31.5
0: coil driver active
1: coil driver inactive
HYSTERESIS
PD
data comparator hysteresis
power down mode enable
select power down mode
0
0
0
0: hysteresis OFF
1: hysteresis ON
0: device active
1: device power down
PD_MODE
0: idle mode
1: power down
FREEZE0
FREEZE1
ACQAMP
facility to achieve fast setting times
facility to achieve fast setting times
0
0
0
see Table 13
see Table 13
store signal amplitude as reference for later
amplitude comparison
see status bit AMPCOMP
THRESET
FSEL0
reset threshold generation of digitizer
clock frequency select LSB
clock frequency select MSB
disable smart comparator
0
0
0
0
00: 4 MHz, 01: 12 MHz
10: 8 MHz, 11: 16 MHz
FSEL1
DISSMARTCOMP
0: smart comparator = ON
1: smart comparator = OFF
DISPL1
disable low pass 1
0
0: low pass = ON
1: low pass = OFF
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
10 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
Table 13. Freeze bit description
FREEZE1 FREEZE0 Meaning
0
0
1
0
1
0
normal operation
main low pass is frozen; main high pass is precharged to QGND
main low pass is frozen; time constant of main high pass is reduced by
a factor of 16 for FILTERH=0 and by a factor 8 for FILTERH=1
1
1
time constant for main high pass is reduced by factor of 16 for
FILTERH=0 and by a factor of 8 for FILTERH=1; second high pass is
precharged
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
11 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
10.8 GET_CONFIG_PAGE
This command has three functions:
1. Reading back the configuration parameters set by SET_CONFIG_PAGE command
2. Reading back the transmit pulse width programmed with WRITE_TAG_N
3. Reading the system status information
P1 and P0 select one of four configuration pages. The response (X3 X2 X1 X0 D3 D2 D1
D0) contains the contents of the selected configuration page in its lower nibble. For P = 0
or P = 1 the higher nibble reflects the current setting of N (the transmit pulse width). For
P = 2 or P = 3 the system status information is returned in the higher nibble.
Table 14. GET_CONFIG_PAGE command
Bit No.
7
6
5
4
3
2
1
0
Remark
Command
0
0
0
0
0
1
P1
D1
P0
D0
Response X3
X2
X1
X0
D3
D2
Table 15. Config pages
Bit No.
7
6
5
4
3
2
1
0
Command/Page no.
GET_CONFIG_PAGE 0 N3
GET_CONFIG_PAGE 1 N3
N2
N2
N1
N1
N0
N0
D3 D2 D1 D0
D3 D2 D1 D0
D3 D2 D1 D0
D3 D2 D1 D0
GET_CONFIG_PAGE 2 0 (RFU)
GET_CONFIG_PAGE 3 0 (RFU)
0 (RFU)
0 (RFU)
AMPCOMP ANTFAIL
AMPCOMP ANTFAIL
Table 16. Status bit description
Bit name
Meaning
ANTFAIL
antenna fail
0: antenna ok
1: antenna failure
AMPCOMP amplitude comparison When ACQAMP is set, the actual amplitude of the data
result
signal is stored as reference. After resetting ACQAMP
status bit AMPCOMP is set when the actual data signal
amplitude is higher than the stored reference.
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
12 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
11. Limiting values
Table 17. Limiting values[1][2][3]
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Min
−0.3
−0.3
−10
-
Max
Unit
V
voltage at any pin except RX
voltage at any pin except RX
voltage at RX pin
+6.5
VDD + 0.3
+12
V
V
Tj
junction temperature
storage temperature
140
°C
°C
Tstg
−65
+125
[1] Stresses above one or more of the limiting values may cause permanent damage to the device.
[2] These are stress ratings only. Operation of the device at these or any other conditions above those given in
the characteristics section of the specification is not implied.
[3] Exposure to limiting values for extended periods may affect device reliability.
12. Characteristics
Table 18. DC characteristics
VSS, Tamb = −40°C to +85 °C.
Symbol
Supply
VDD
Parameter
Conditions
Min
Typ
Max
Unit
supply voltage
4.5
5.0
4
5.5
10
V
IOn
operating supply current
idle current
VDD = 5.5 V, ITX1 = ITX2 = 0
VDD = 5.5 V
-
-
-
mA
mA
μA
[1]
Iid
0.2
7
0.4
20
Ipd
power-down current
VDD = 5.5 V
Drivers (TX1, TX2)
Iant
output peak-current
permanent
-
-
-
-
200
400
7
mAp
mAp
Ω
IantPulse
output peak-current
output resistance
1:4 on/off-ratio ton <400 ms
both drivers together
-
2.5
Demodulator input
voltage range
URX with respect to QGND
−8
-
8
V
QGND potential
impedance
0.35 VDD 0.35 VDD 0.35 VDD
V
Rdem_in
17
25
33
kΩ
Diagnosis level (DLEV)
DLEV
URX with respect to QGND,
VDD = 5 V
−1.5
−1.15
−0.8
V
Digital inputs
VIH
VIL
HIGH-level input voltage
LOW-level input voltage
0.7 VDD
-
-
VDD + 0.3 V
0.3 VDD
V
V
−0.3
Digital outputs
VOL LOW-level output voltage
output drive capability
IOLmax = + 1mA
-
-
-
0.4
-
V
VOL ≤ 0.4 V
1
mA
[1] Power consumption of external quartz or any other external component is not included.
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
13 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
Table 19. AC characteristics
Tamb = −40°C to +85 °C.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
XTAL oscillator (XTAL1/XTAL2)
FOSC
tstartup
Ci
frequency range
start-up time
depending on FSEL
4
-
16
10
-
MHz
ms
-
4
input capacitance
input resistance
XTAL1
-
5
pF
Ri
XTAL1 to XTAL2
0.9
1.3
3.0
MΩ
External clock (XTAL1)
frequency range
depending on FSEL
4
-
16
60
MHz
%
δ
duty cycle
40
Serial interface
TS
setup time
MODE pin at VSS
MODE pin at VSS
50
50
ns
ns
TH
hold time
Receiver
URX
sensitivity
at RX input
FILTERL = 0
FILTERL = 1
2
1
mVPP
μs
TRCV0
TRCV1
receiver delay
receiver delay
290
160
310
175
340
190
μs
Recovery from clock stable to demodulator valid
TRFD recovery time demodulator
Recovery from WRITE-pulse
[1]
[1]
-
-
-
-
5
ms
TRWD
recovery time demodulator
500
μs
Recovery from AST-step
TRAST
recovery of demodulator
phase measurement error
-
-
0.7
-
1.5
ms
±5.7
deg
[1] These short times require special command sequences. Please refer to the application note "AN98080 Read/Write Devices based on
the HITAG Read/Write IC HTRC110".
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
14 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
13. Package information
Fig 5. Package information
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
15 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
14. Package outline
SO14: plastic small outline package; 14 leads; body width 3.9 mm
SOT108-1
D
E
A
X
c
y
H
v
M
A
E
Z
8
14
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
7
e
detail X
w
M
b
p
0
2.5
scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
Z
θ
1
2
3
p
E
max.
0.25
0.10
1.45
1.25
0.49
0.36
0.25
0.19
8.75
8.55
4.0
3.8
6.2
5.8
1.0
0.4
0.7
0.6
0.7
0.3
mm
1.75
1.27
0.05
1.05
0.25
0.01
0.25
0.1
0.25
0.01
8o
0o
0.010 0.057
0.004 0.049
0.019 0.0100 0.35
0.014 0.0075 0.34
0.16
0.15
0.244
0.228
0.039 0.028
0.016 0.024
0.028
0.012
inches
0.041
0.01 0.004
0.069
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
REFERENCES
JEDEC JEITA
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
99-12-27
03-02-19
SOT108-1
076E06
MS-012
Fig 6. Package outline SOT108-1
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
16 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
15. Abbreviations
Table 20. Abbreviations
Acronym
AST
Description
Adaptive Sampling Time technique
Most Significant Bit
MSB
Û, Î
amplitudes of sine shaped signals
peak-to-peak of arbitrary shaped signals
zero-to-peak of arbitrary shaped signals
Upp, Ipp
Up, Ip
16. References
[1] Application note — AN98080 Read/Write Devices based on the HITAG
Read/Write IC HTRC110, document number: 0355**1
1. ** ... document version number
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
17 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
17. Revision history
Table 21. Revision history
Document ID
037031
Release date
20090209
Data sheet status
Change notice
Supersedes
037030
Product data sheet
Modifications:
• The format of this data sheet has been redesigned to comply with the new identity
guidelines of NXP Semiconductors.
• Legal texts have been adapted to the new company name where appropriate.
• General update
037030
037022
July 2006
Product data sheet
037022
January 1999
Preliminary data sheet
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
18 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
18. Legal information
18.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
malfunction of an NXP Semiconductors product can reasonably be expected
18.2 Definitions
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on a weakness or default in the
customer application/use or the application/use of customer’s third party
customer(s) (hereinafter both referred to as “Application”). It is customer’s
sole responsibility to check whether the NXP Semiconductors product is
suitable and fit for the Application planned. Customer has to do all necessary
testing for the Application in order to avoid a default of the Application and the
product. NXP Semiconductors does not accept any liability in this respect.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
18.3 Disclaimers
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Non-automotive qualified products — Unless the data sheet of an NXP
Semiconductors product expressly states that the product is automotive
qualified, the product is not suitable for automotive use. It is neither qualified
nor tested in accordance with automotive testing or application requirements.
NXP Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
19 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
18.4 Licenses
ICs with HITAG functionality
NXP Semiconductors owns a worldwide perpetual license for the patents
US 5214409, US 5499017, US 5235326 and for any foreign counterparts
or equivalents of these patents. The license is granted for the Field-of-Use
covering: (a) all non-animal applications, and (b) any application for animals
raised for human consumption (including but not limited to dairy animals),
including without limitation livestock and fish.
Please note that the license does not include rights outside the specified
Field-of-Use, and that NXP Semiconductors does not provide indemnity for
the foregoing patents outside the Field-of-Use.
18.5 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
HITAG — is a trademark of NXP B.V.
19. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
20 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
20. Tables
Table 1. Ordering information . . . . . . . . . . . . . . . . . . . . .2
Table 2. Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .3
Table 3. HTRC110 commands . . . . . . . . . . . . . . . . . . . . .8
Table 4. READ_TAG command . . . . . . . . . . . . . . . . . . . .8
Table 5. READ_TAG_N command . . . . . . . . . . . . . . . . . .8
Table 6. WRTIE_TAG command . . . . . . . . . . . . . . . . . . .9
Table 7. READ_PHASE command. . . . . . . . . . . . . . . . . .9
Table 8. SET_SAMPLING_TIME command. . . . . . . . . . .9
Table 9. GET_SAMPLING_TIME command . . . . . . . . . .9
Table 10. SET_CONFIG_PAGE command . . . . . . . . . . .10
Table 11. Config pages. . . . . . . . . . . . . . . . . . . . . . . . . . .10
Table 12. Bit initial conditions . . . . . . . . . . . . . . . . . . . . . 10
Table 13. Freeze bit description. . . . . . . . . . . . . . . . . . . . 11
Table 14. GET_CONFIG_PAGE command. . . . . . . . . . . 12
Table 15. Config pages . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 16. Status bit description . . . . . . . . . . . . . . . . . . . . 12
Table 17. Limiting values[1][2][3] . . . . . . . . . . . . . . . . . . . . 13
Table 18. DC characteristics . . . . . . . . . . . . . . . . . . . . . . 13
Table 19. AC characteristics . . . . . . . . . . . . . . . . . . . . . . 14
Table 20. Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 21. Revision history . . . . . . . . . . . . . . . . . . . . . . . . 18
21. Figures
Fig 1. Block diagram HTRC110 . . . . . . . . . . . . . . . . . . . .2
Fig 2. Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . .3
Fig 3. Minimum application circuitry. . . . . . . . . . . . . . . . .4
Fig 4. Serial signaling . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Fig 5. Package information . . . . . . . . . . . . . . . . . . . . . .15
Fig 6. Package outline SOT108-1 . . . . . . . . . . . . . . . . .16
037031
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
PUBLIC
Rev. 3.1 — 9 February 2010
037031
21 of 22
HTRC110
NXP Semiconductors
HITAG reader chip
22. Contents
1
2
3
4
5
General description . . . . . . . . . . . . . . . . . . . . . . 1
21
22
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
7
8
Key data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Minimum application circuitry . . . . . . . . . . . . . 4
9
Functional description . . . . . . . . . . . . . . . . . . . 5
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Antenna driver, data input. . . . . . . . . . . . . . . . . 5
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Oscillator/programmable divider/clock . . . . . . . 5
Adaptive sampling time demodulator . . . . . . . . 5
Idle and power-down mode . . . . . . . . . . . . . . . 6
Serial interface . . . . . . . . . . . . . . . . . . . . . . . . . 7
Glitch filter for increased noise/interference
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
10
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
READ_TAG. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WRITE_TAG_N . . . . . . . . . . . . . . . . . . . . . . . . 8
WRITE_TAG. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
READ_PHASE . . . . . . . . . . . . . . . . . . . . . . . . . 9
SET_SAMPLING_TIME . . . . . . . . . . . . . . . . . . 9
GET_SAMPLING_TIME . . . . . . . . . . . . . . . . . 9
SET_CONFIG_PAGE. . . . . . . . . . . . . . . . . . . 10
GET_CONFIG_PAGE. . . . . . . . . . . . . . . . . . . 12
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
11
12
13
14
15
16
17
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 13
Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . 13
Package information . . . . . . . . . . . . . . . . . . . . 15
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 17
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 18
18
Legal information. . . . . . . . . . . . . . . . . . . . . . . 19
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 19
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
18.1
18.2
18.3
18.4
18.5
19
20
Contact information. . . . . . . . . . . . . . . . . . . . . 20
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2010.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 9 February 2010
037031
相关型号:
©2020 ICPDF网 联系我们和版权申明