LM324D/T3 [NXP]
QUAD OP-AMP, 9000uV OFFSET-MAX, 1MHz BAND WIDTH, PDSO14, 3.90 MM, PLASTIC, SOT-108-1, SO-14;
| 型号： | LM324D/T3 |
| 厂家： | 
NXP |
| 描述： | QUAD OP-AMP, 9000uV OFFSET-MAX, 1MHz BAND WIDTH, PDSO14, 3.90 MM, PLASTIC, SOT-108-1, SO-14 放大器 光电二极管 |
| 文件： | 总12页 (文件大小：127K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
Product data
2003 Sep 19
Supersedes data of 2002 Jul 12
Philips
Semiconductors
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
DESCRIPTION
PIN CONFIGURATION
The LM124/SA534/LM2902 series consists of four independent,
high-gain, internally frequency-compensated operational amplifiers
designed specifically to operate from a single power supply over a
wide range of voltages.
D, DH, and N Packages
1
2
3
4
5
6
7
14
13
12
11
10
9
OUTPUT 1
OUTPUT 4
4
1
–INPUT 1
+INPUT 1
–INPUT 4
+INPUT 4
+ –
– +
UNIQUE FEATURES
In the linear mode, the input common-mode voltage range includes
ground and the output voltage can also swing to ground, even
though operated from only a single power supply voltage.
GND
V +
+INPUT 3
The unity gain crossover frequency and the input bias current are
temperature-compensated.
+INPUT 2
–INPUT 2
– +
2
+ –
3
–INPUT 3
8
OUTPUT 3
OUTPUT 2
FEATURES
• Internally frequency-compensated for unity gain
TOP VIEW
SL00065
• Large DC voltage gain: 100 dB
Figure 1. Pin configuration.
• Wide bandwidth (unity gain): 1 MHz (temperature-compensated)
• Wide power supply range Single supply: 3 V to 30 V or dual
DC
DC
supplies: ±1.5 V to ±15 V
DC
DC
• Very low supply current drain: essentially independent of supply
voltage (1 mW/op amp at +5 V
)
DC
• Low input biasing current: 45 nA (temperature-compensated)
DC
• Low input offset voltage: 2 mV and offset current: 5 nA
DC
DC
• Differential input voltage range equal to the power supply voltage
• Large output voltage: 0V to V –1.5 V swing
DC
CC
DC
ORDERING INFORMATION
DESCRIPTION
14-Pin Plastic Dual In-Line Package (DIP)
TEMPERATURE RANGE
ORDER CODE
LM124N
DWG #
SOT27-1
SOT108-1
SOT27-1
SOT108-1
SOT27-1
SOT108-1
SOT402-1
SOT27-1
SOT108-1
SOT27-1
SOT108-1
SOT402-1
SOT27-1
–55° C to +125 °C
–25 °C to +85 °C
–25 °C to +85 °C
0 °C to +70 °C
14-Pin Plastic Small Outline (SO) Package
14-Pin Plastic Dual In-Line Package (DIP)
14-Pin Plastic Small Outline (SO) Package
14-Pin Plastic Dual In-Line Package (DIP)
14-Pin Plastic Small Outline (SO) Package
14-Pin Plastic Thin Shrink Small Outline Package (TSSOP)
14-Pin Plastic Dual In-Line Package (DIP)
14-Pin Plastic Small Outline (SO) Package
14-Pin Plastic Dual In-Line Package (DIP)
14-Pin Plastic Small Outline (SO) Package
14-Pin Plastic Thin Shrink Small Outline Package (TSSOP)
14-Pin Plastic Dual In-Line Package (DIP)
LM224D
LM224N
LM324AD
LM324AN
LM324D
0 °C to +70 °C
0 °C to +70 °C
0 °C to +70 °C
LM324DH
LM324N
0 °C to +70 °C
–40 °C to +85 °C
–40 °C to +85 °C
–40 °C to +125 °C
–40 °C to +125 °C
–40 °C to +125 °C
SA534D
SA534N
LM2902D
LM2902DH
LM2902N
2
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
RATING
32 or ±16
32
UNIT
V
CC
V
IN
V
IN
P
D
Supply voltage
V
DC
V
DC
V
DC
Differential input voltage
Input voltage
–0.3 to +32
1
Maximum power dissipation, T
= 25 °C (still-air)
amb
N package
D package
DH package
1420
1040
762
mW
mW
mW
2
Output short-circuit to GND one amplifier
Continuous
50
V
< 15 V and T = 25 °C
amb
CC
DC
3
I
IN
Input current (V < –0.3 V)
mA
IN
Operating ambient temperature range
T
amb
LM324/324A
LM224
SA534
LM2902
LM124
0 to +70
–25 to +85
–40 to +85
–40 to +125
–55 to +125
°C
°C
°C
°C
°C
T
Storage temperature range
–65 to +150
230
°C
°C
stg
T
sld
Lead soldering temperature (10 sec max)
NOTES:
1. Derate above 25 °C at the following rates:
N package at 11.4 mW/°C
D package at 8.3 mW/°C
DH package at 6.1mW/°C
2. Short-circuits from the output to V + can cause excessive heating and eventual destruction. The maximum output current is approximately
CC
40 mA, independent of the magnitude of V . At values of supply voltage in excess of +15 V continuous short-circuits can exceed the
CC
DC
power dissipation ratings and cause eventual destruction.
3. This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the
input PNP transistors becoming forward biased and thereby acting as input bias clamps. In addition, there is also lateral NPN parasitic
transistor action on the IC chip. This action can cause the output voltages of the op amps to go to the V+ rail (or to ground for a large
overdrive) during the time that the input is driven negative.
3
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
DC ELECTRICAL CHARACTERISTICS
V
CC
= 5 V; T
= 25 °C, unless otherwise specified.
amb
LM124/LM224
LM324/SA534/LM2902
UNIT
SYMBOL
PARAMETER
TEST CONDITIONS
= 0 Ω
Min
Typ
Max
Min
Typ
Max
±7
R
±2
±5
±7
±2
S
1
V
OS
Offset voltage
mV
µV/°C
nA
R = 0 Ω, over temp.
S
±9
∆V /∆T Temperature drift
R = 0 Ω, over temp.
S
7
7
OS
I
IN
(+) or I (–)
45
40
50
±3
150
300
45
40
50
±5
250
500
IN
2
I
Input current
/∆T Temperature drift
Offset current
BIAS
I
(+) or I (–), over temp.
IN
IN
∆I
Over temp.
pA/°C
nA
BIAS
I
IN
(+)–I (–)
±30
±50
IN
I
OS
I
(+)–I (–), over temp.
±100
±150
IN
IN
∆I /∆T
Temperature drift
Over temp.
10
10
pA/°C
V
OS
V
CC
≤ 30 V
0
0
V
–1.5
0
0
V
–1.5
Common-mode voltage
CC
CC
V
CM
3
range
V
CC
≤ 30 V; over temp.
V
–2
V
–2
CC
CC
Common-mode rejection
ratio
CMRR
V
= 30 V
70
26
27
85
65
26
27
70
dB
V
CC
R = 2 kΩ, V = 30 V,
L
CC
V
OUT
Output voltage swing
over temp.
R ≤ 10 kΩ, V = 30 V,
L
CC
V
V
Output voltage high
Output voltage low
28
28
V
OH
over temp.
R ≤ 10 kΩ; over temp.
5
20
3
5
20
3
mV
OL
L
R = ∞, V = 30 V; over temp.
1.5
0.7
1.5
0.7
L
CC
I
Supply current
mA
CC
R = ∞; over temp.
1.2
1.2
L
V
V
= 15 V (for large V swing);
O
CC
50
25
100
25
15
100
R ≥ 2 kΩ
L
A
Large-signal voltage gain
Amplifier-to-amplifier
V/mV
VOL
= 15 V (for large V swing);
CC
O
R ≥ 2k Ω; over temp.
L
f = 1 kHz to 20 kHz,
input referred
–120
100
40
–120
100
40
dB
dB
5
coupling
PSRR
Power supply rejection ratio
R
≤ 0 Ω
65
20
65
20
S
V
V
V
V
V
+ = +1 V, V – = 0 V,
IN
IN
V
CC
= 15 V
Output current source
+ = +1 V, V – = 0 V,
IN
V
IN
10
10
5
20
20
8
10
10
5
20
20
8
= 15 V, over temp.
CC
mA
– = +1 V, V + = 0 V,
IN
IN
I
OUT
V
CC
= 15 V
– = +1 V, V + = 0 V,
IN
V
IN
Output current sink
= 15 V, over temp.
CC
– = +1 V, V + = 0 V,
IN
IN
12
10
50
12
10
50
µA
V
O
= 200 mV
4
I
Short-circuit current
40
1
60
40
1
60
mA
MHz
V/µs
nV/√Hz
V
SC
GBW
SR
Unity gain bandwidth
Slew rate
0.3
40
0.3
40
V
Input noise voltage
f = 1 kHz
NOISE
DIFF
3
V
Differential input voltage
V
CC
V
CC
4
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
DC ELECTRICAL CHARACTERISTICS (Continued)
V
CC
= 5 V, T
= 25 °C unless otherwise specified.
amb
LM324A
UNIT
SYMBOL
PARAMETER
TEST CONDITIONS
= 0 Ω
Min
Typ
Max
±3
R
±2
S
1
V
OS
Offset voltage
mV
µV/°C
nA
R
R
= 0 Ω, over temp.
= 0 Ω, over temp.
±5
S
S
∆V /∆T
Temperature drift
7
30
OS
I
IN
(+) or I (–)
45
40
50
±5
100
200
IN
2
I
Input current
BIAS
I
(+) or I (–), over temp.
IN
IN
∆I
BIAS
/∆T
Temperature drift
Offset current
Over temp.
pA/°C
nA
I
IN
(+)–I (–)
±30
±75
300
IN
I
OS
I
(+)–I (–), over temp.
IN
IN
∆I /∆T
OS
Temperature drift
Over temp.
10
85
pA/°C
V
CC
≤ 30 V
0
V
–1.5
V
V
CC
3
V
CM
Common-mode voltage range
V
CC
≤ 30 V, over temp.
0
V
–2
CC
CMRR
Common-mode rejection ratio
Output voltage swing
V
CC
= 30 V
65
26
27
dB
V
V
OUT
V
OH
R = 2 kΩ, V = 30 V; over temp.
L CC
Output voltage high
R ≤ 10 kΩ, V = 30 V; over temp.
28
5
V
L
CC
R ≤ 10 kΩ,
L
V
OL
Output voltage low
Supply current
20
mV
over temp.
R = ∞, V = 30 V, over temp.
1.5
0.7
3
mA
mA
L
CC
I
CC
R = ∞, over temp.
L
1.2
V
= 15 V (for large V swing), R ≥ 2 kΩ
25
15
100
V/mV
CC
O
L
A
VOL
Large-signal voltage gain
V
CC
= 15 V (for large V swing), R ≥ 2k Ω,
O
L
V/mV
dB
over temp.
f = 1 kHz to 20 kHz,
input referred
5
Amplifier-to-amplifier coupling
–120
PSRR
Power supply rejection ratio
R
≤ 0 Ω
65
20
100
40
dB
S
V
IN
+ = +1 V, V – = 0 V, V = 15 V
mA
IN
CC
Output current source
Output current sink
V
+ = +1 V, V – = 0 V, V = 15 V,
IN
IN
CC
10
10
5
20
20
8
mA
mA
mA
over temp.
V
V
– = +1 V, V + = 0 V V = 15 V
IN , CC
I
IN
OUT
– = +1 V, V + = 0 V, V = 15 V,
IN
IN
CC
over temp.
V
IN
– = +1 V, V + = 0 V, V = 200 mV
12
10
50
40
µA
mA
IN
O
4
I
Short-circuit current
60
SC
3
V
DIFF
Differential input voltage
V
CC
V
GBW
SR
Unity gain bandwidth
Slew rate
1
MHz
V/µs
nV/√Hz
0.3
40
V
NOISE
Input noise voltage
f = 1 kHz
NOTES:
1. V ≈ 1.4 V , R = 0 Ω with V from 5 V to 30 V and over full input common-mode range (0 V + to V –1.5 V).
O
DC
S
CC
DC
CC
2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of
the output so no loading change exists on the input lines.
3. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common-mode voltage range is V –1.5, but either or both inputs can go to +32 V without damage.
CC
4. Short-circuits from the output to V can cause excessive heating and eventual destruction. The maximum output current is approximately
CC
40 mA independent of the magnitude of V . At values of supply voltage in excess of +15 V , continuous short-circuits can exceed the
CC
DC
power dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers.
5. Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of coupling increases at higher frequencies.
5
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
EQUIVALENT CIRCUIT
v
+
6 µA
100 µA
6 µA
Q5
Q7
Q6
C
C
R
SC
Q2
Q3
OUTPUT
Q1
Q4
INPUTS
+
Q11
Q13
Q10
Q12
50 µA
Q8
Q9
SL00066
Figure 2. Equivalent circuit.
6
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
TYPICAL PERFORMANCE CHARACTERISTICS
Output Characteristics
Current Sourcing
Supply Current
Current Limiting
4
8
90
V+
80
7
6
+
3
+V /2
70
60
V
2
+
–
5
4
I
50
40
O
2
INDEPENDENT OF V+
30
20
10
0
3
o
= +25 C
amb
+
T
1
0
T
amb
= 0 °C to 125 °C
2
1
T
amb
= –55 °C
0
0.001
0.01
0.1
1
10
100
10
SUPPLY VOLTAGE (V
20
30
)
40
55 35 –15
5
25 45 65 85 105 125
+
I
O
– OUTPUT SOURCE CURRENT (mA
)
DC
TEMPERATURE (°C)
DC
OP05450S
OP05460S
OP05470S
Output Characteristics
Current Sinking
Open–Loop Frequency
Response
Voltage Gain
140
160
120
10
1
+
V
10 M
+
V
+
= +5 V
= +15 V
= +30 V
DC
DC
DC
0.1 µf
120
100
V
R
+ 20 kΩ
L
–
V
IN
+
V
+
V
O
+
V /2
R
+ 2 kΩ
L
80
60
40
+
+
V
V
= 30 V AND
DC
80
40
0
–55 °C ≤ T
≤ +125 °C
amb
–
+
V
/2
0.1
I
O
+
V
O
+
V
= 10 to 15 V AND
DC
–55 °C ≤ T
≤ +125 °C
amb
20
0
T
= +25 °C
amb
0.01
0.001 0.01
0.1
1
10
100
1
10 100
1K 10K 100K 1M 10M
0
10
20
30
40
I
O
– OUTPUT SINK CURRENT (mA
)
DC
SUPPLY VOLTAGE (V
)
FREQUENCY (Hz)
OP05500S
DC
OP05480S
OP05490S
SL00067
Figure 3. Typical Performance Characteristics
7
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
Large-Scale
Frequency Response
Voltage-Follower
Pulse Response
Input Voltage Range
4
3
20
15
15
+ =
15 V
DC
V
R
< 2K V
DC
L
100 kΩ
1 kΩ
2
1
0
V
O
–
+
10
V
IN
NEGATIVE
+
2 kΩ
7V
DC
10
5
POSITIVE
3
5
2
1
0
0
1K
10K
100K
1M
0
10
20
TIME (µS)
30
40
0
5
10
15
FREQUENCY (Hz)
— POWER SUPPLY VOLTAGE (+ V
+
)
DC
V
OR V–
Voltage-Follower Pulse
Response (Small–Signal)
Input Current
Common-Mode Rejection Ratio
120
500
90
V
= 0 V
DC
CM
80
70
60
100
450
400
350
E
50pF
O
+
V
+
= +30 V
DC
V
IN
80
60
40
+7.5 V
DC
50
40
30
100k
V
= +15 V
DC
100
INPUT
V
–
O
OUTPUT
100
+
+
V
+
IN
20
10
0
V
= +5 V
DC
100k
300
250
20
0
7.5 V
DC
o
T
V
= +25 C
= +30 V
amb
+
DC
1k
10k
100k
–55 –35 –15
5
25 45 65 85 105 125
100
1M
0
1
2
3
4
5
6
7
8
o
T
— TEMPERATURE (C )
f — FREQUENCY (Hz)
L — TIME (µS)
amb
SL00068
Figure 4. Typical Performance Characteristics (cont.)
TYPICAL APPLICATIONS
V+
RF
V+
V+
V+
V+
8
4
R
2
IN
V+
10K
–
+
10K
V
IN
V
O
8
8
V
IN
+
–
V
V
O
IN
+
–
4
RL
V
O
4
V+
2
10k
10k
BLOCKS
DC.
GAIN
RF
R
1
Single Supply Inverting Amplifier
Non–Inverting Amplifier
Input Biasing Voltage–Follower
SL00069
Figure 5. Typical Applications
8
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
DIP14: plastic dual in-line package; 14 leads (300 mil)
SOT27-1
9
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
SO14: plastic small outline package; 14 leads; body width 3.9 mm
SOT108-1
10
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm
SOT402-1
11
2003 Sep 19
Philips Semiconductors
Product data
LM124/224/324/324A/
SA534/LM2902
Low power quad op amps
REVISION HISTORY
Rev
Date
Description
_5
20030919
Product data (9397 750 12078). ECN 853-0929 30369 of 19 September 2003.
Modifications:
• Modified Figure 2; Q10 and Q13 changed from NPN to PNP.
_4
20020712
Product data (9397 750 10172). ECN 853-0929 28616 of 12 July 2002.
Data sheet status
Product
status
Definitions
[1]
Level
Data sheet status
[2] [3]
I
Objective data
Development
This data sheet contains data from the objective specification for product development.
Philips Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data
Qualification
Production
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
[1] Please consult the most recently issued data sheet before initiating or completing a design.
[2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL
http://www.semiconductors.philips.com.
[3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see
the relevant data sheet or data handbook.
Limitingvaluesdefinition— Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given
in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no
representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be
expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree
to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes in the products—including circuits, standard cells, and/or software—described
or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated
viaaCustomerProduct/ProcessChangeNotification(CPCN).PhilipsSemiconductorsassumesnoresponsibilityorliabilityfortheuseofanyoftheseproducts,conveys
nolicenseortitleunderanypatent, copyright, ormaskworkrighttotheseproducts, andmakesnorepresentationsorwarrantiesthattheseproductsarefreefrompatent,
copyright, or mask work right infringement, unless otherwise specified.
Koninklijke Philips Electronics N.V. 2003
Contact information
All rights reserved. Printed in U.S.A.
For additional information please visit
http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
Date of release: 09-03
9397 750 12078
For sales offices addresses send e-mail to:
sales.addresses@www.semiconductors.philips.com.
Document order number:
Philips
Semiconductors
©2020 ICPDF网 联系我们和版权申明