MC33191DW [NXP]
IC,AUTOMOTIVE,IGNITION CIRCUIT,SOP,16PIN,PLASTIC;型号: | MC33191DW |
厂家: | NXP |
描述: | IC,AUTOMOTIVE,IGNITION CIRCUIT,SOP,16PIN,PLASTIC 光电二极管 |
文件: | 总5页 (文件大小:307K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Freescale Semiconductor, Inc.
MOTOROLA
MC33191
SEMICONDUCTOR
TECHNICAL DATA
12V IGNITION DRIVER
Prototype Information
SILICON MONOLITHIC
INTEGRATED CIRCUIT
Automotive 12V ignition driver
The MC33191 is for use in 12V ignition systems designed for use in
harsh automotive and industrial applications which require the capability of
handling high voltage attributed to load and Þeld dump transients. In
addition, the device can be used under reverse and double battery
conditions.
DW SUFFIX
PLASTIC PACKAGE
CASE 751G
SO-16L
The MC33191 is available in a 16 pin narrow body DIP plastic and SO
package.
PIN ASSIGNMENT
¥ Designed for Automotive Ignition Application
¥ Continuous System Voltage up to 28.6V
¥ Continuous Operating Ambient Temperature Range from -30°C
to +125°C
¥ Frequency Range from 1Hz to 400 Hz
¥ Coil Current Regulation
1
2
3
4
5
6
7
8
16
Gnd
Vcc
in+
15 ÔÕDÕÕ.
ÔÕCÕÕ
14
in-
Output
Isr
13
12
11
H.V.C.
I.S.
C stall
VLS
C25/75
Cad
¥ Hall Effect and Reluctance Sensor Applications.
M.B
10
9
Vreg
ORDERING INFORMATION
Temperature
Device
Package
DIL16
Range
MC33191P
-30°C to +125°C
SimpliÞed Block Diagram
15
9
10(MB)
1
Vreg
12
14
Band
Gap
Series
Reg.
Vcc
-
2
3
1.5KW
Input
+
13
11
20mA
Current
sense
80mA
LOGIC
Vreg
Vreg
Vreg
Retard
Stall
6mA
5
4
6.7mA
25/75
8mA
31.8mA
to
26.8mA
Slow
Speed
80mA
3.2mA
1.92mA
Adapt
dwell
GND
16
6
7
8
This document contiains information on a new product under development. Motorola reserves
the right to change or discontinue this product without notice.
Ó Motorola,Inc
Date : 10/12/98
Rev : 1.0
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC33191
DEVICE PIN OUT IDENTIFICATION
Pin
Function
Pin
Function
1
2
3
4
5
6
7
8
V
9
V
reg
cc
Input +
Input -
10
11
12
13
14
15
16
Master Bias
Current Sense
High Voltage Clamp
Output
Start Retard I Trim
Stall Capacitor
V Low Speed
25/75 Capacitor
Adaptive Dwell Cap.
ÔÕ C ÔÕ
ÔÕ D ÔÕ
Master bias
ELECTRICAL REQUIREMENTS The IC performs to the limits of the table between temperature range of - 30°C to +125°C and it operates between the tempera-
ture range of - 40°C to +150°C
Symbol
Description
Min
Max
Unit
ICC
I.C.Drain Current
Regulator output voltage
I.C. Drain Current High Voltage
(+) Input, Positive Clamp
(+) Input, Negative Clamp
(-) Input, Positive Clamp
(-) Input, Negative Clamp
Input Threshold
3
5
7,1
10
mA
V
V
6,5
reg
ICCH
mA
V
V
V
(+) P
7
1
8
in
in
(+) N
(-) P
(-) N
2
V
V
7
8
V
in
in
V
1
2
V
V
TH
-25
280
54
+25
372
88
mA
mV
mV
mA
in
V
Hys. RM
Hys. SS
I75
Run Mode Hysteresis
in
V
Slow Speed Hysteresis
25/75 Current Up
in
6.2
7.68
0.365
0.878
1.7
2.66
19
I75 / I25
I75 / I25 Current ratio
0.317
0.794
1.49
2.35
15.5
1.05
3.9
I75 / I ADU
I ADU / IADD
I ADU / IADR
VEDR
I75 / IADU Current ratio
IADU / IADD Current ratio
I ADU / I ADR Current ratio
Reduced Excess Dwell Trip Voltage
I 75 / I SU Current Ratio
I SD/ I SU Current ratio
Collector Clamp Voltage
Current Sense Voltage
Output Saturation Voltage
Output Leakage Current
Overvoltage Shutdown Voltage
Slow Speed Stall
V
I 75 / ISU
I SD / I SU
VHVC
1.27
4.95
16.7
185
985
25
14.4
133
V
mV
mV
mA
V
VCS
VOS
IOLK
VOSD
27
30
VSSS
2.4
3.1
V
MC33191
MOTOROLA
2
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC33191
Figure 1.Test Schematic
Vbat
300W
Vbat
1 Vcc
2 In+
GND 16
ÔÕDÕÕ 15
5.1KW
5.1KW
68W
6.8V
33W
3 In-
4 Isr
ÔÕCÔÕ 14
OUT 13
Clamp 12
IS 11
5 Cs
6 Vls
500W
7 C25/75
8 Cod
MB 10
Vreg
9
57KW
26KW
Figure 2. Application Circuit (Reluctance Sensor Input)
+
-
Ign
200
0.1
Battery
1/2W
68
2.5W
Ground
Vcc
1
2
3
4
5
6
7
8
16
15
14
13
6.8V
Ignition
Coil
5.0W
+Sensor
IN+
D
C
5.0k
5.0k
0.1
0.1
Reluctance
33
1/4W
-Sensor
IN-
5k
Q1
Retard
Output
200
Stall
Clamp 12
1.0
400
Slow
Current
Sense
11
10
9
Speed
200/400
16k
.05
25/75
Bias
Vref
400
57k
Gnd
0.1
0.1
Adaptive
Dwell
NOTE :
10k
1. Q1 = BUZ111 or Eqivalent
2. T = Trim Resistors
MC33191
MOTOROLA
3
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC33191
Figure 3. Application Circuit (Hall Sensor Input)
85
+
-
Hall Voltage
Hall Output
Ign
Battery
0.1
1.1k
68
2.5W
200
1/2W
18V
100
Ground
Vcc
1
16
15
14
13
12
11
10
9
Ignition
Coil
6.8V
5.0W
Engine
Microcontroller
0.1
4.7k
IN+
D
C
2
3
4
5
6
7
8
10k
0.1
33
1/4W
IN-
5k
Q1
Retard
Output
200
5.0k
Stall
Clamp
1.0
400
400
3.0k
T
Slow
Speed
Current
Sense
285
T
16k
.05
25/75
Bias
Vref
5.1k
T
Gnd
0.1
0.1
57k
Adaptive
Dwell
10k
NOTE :
1. Q1 = BUZ111 or Eqivalent
2. T = Trim Resistors
MC33191
MOTOROLA
4
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC33191
FUNCTIONNAL DESCRIPTION
Application /System Performances
- No separate start wire into module is required
- Switch occurs at approximatly 12Hz but can be
changed within a narrow region
1. Reluctance sensor input.
- Minimum input level of 200mV peak to peak
- Maximum input level of 40V peak to peak
5. Input noise immunity is provided by hysteresis on the
input comparator.
2. Hall sensor input
- Open collector output desirable.
- Input level of 0.5V to Vbat
- 100mV of hysteresis is in slow speed mode
- 500mV of hysteresis in run mode
3. Operating voltage range
- Normal range from 9V to 16V.
-Operational range with some modiÞcations to
parameters from 6V to 24V.
6. Dwell control is modiÞed under different operating
conditions.
- In slow speed mode dwell follows the duty cycle of the
input signal
- In normal run mode dwell is controlled at 16% of cycle
time plus coil rise time to current limit level.
- At high speed (determined by coil rise time) dwell is
75% of input cycle time.
4.Transient considerations
- Load dumps should not exceed +90V peak with 250ms
time constant.
- Field decay should not exceed -90V peak with 25ms
time constant.
7. Output current is normally 5.5 +/- 0.5 Amps. It can be
operated at higher or lower limits if required. (Not excluding
7.5 Amps).
5. Operating temperature range
- Continuous operation : -30°C to 125°C
8. Start Retard
6. Rate of acceleration should not exceed 250Hz/s from
20Hz to 300Hz (input frequency). If this is exceeded the
module will still function but an occasional spark may be
missed and dwell calculations will be negated for one or two
output cycles.
On slow speed mode, a retard signal is generated that is
inversely proportional to input frequency. The retard is
nominally 4.8% at 1Hz, (related to input duty cycle) and can
be modiÞed to meet other application requirement.
9. High voltage on the output transistor is nominally
clamped at 350V but can be adjusted if necessary.
7. Normal operating frequency range is from 1Hz to
400Hz.
10. High Battery voltage operation
- At a battery voltage of 16V the dwell is modiÞed in run
speed to 10% of cycle time plus coil rise time.
- At a battery voltage of approximately 30V the module
will shutdown to prevent damages to the output devices.
Application features and functions
1. Power on : On initial power up there will be no output
current and this condition will be maintained until the Þrst
input cycle is run at the input terminals.
2. Push start capability :The unit may be push started as
any input signal exceeding 200mV peak to peak will produce
a peak
3. Stall shutdown : If for a period of 5 seconds no input
signal is present, the unit will shutdown and output current
will be reduced at a rate slow enough to present a spark.
4. Automatic switching from a slow speed to run mode at
a preset frequency.
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. ªTypicalº parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,includingªTypicalsº
must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
MC33191
MOTOROLA
5
For More Information On This Product,
Go to: www.freescale.com
相关型号:
©2020 ICPDF网 联系我们和版权申明