MCZ14600EG/R2 [NXP]
SPECIALTY CONSUMER CIRCUIT, PDSO16, LEAD FREE, SOIC-16;型号: | MCZ14600EG/R2 |
厂家: | NXP |
描述: | SPECIALTY CONSUMER CIRCUIT, PDSO16, LEAD FREE, SOIC-16 光电二极管 商用集成电路 |
文件: | 总8页 (文件大小:249K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Archived by Freescale Semiconductor, Inc., 2009
Document Number: MC14600
Rev. 7.0, 6/2007
Freescale Semiconductor
Technical Data
Low-Power CMOS
ALARM IC with Horn Driver
14600
The MC14600 Alarm IC is designed to simplify the process of interfacing an
alarm level voltage condition to a piezoelectric horn and/or LED. With an
extremely low average current requirement and an integrated low battery detect
feature, the part is ideally suited to battery operated applications. The MC14600
is easily configured with a minimum number of external components to serve a
wide range of applications and circuit configurations. Typical applications include
intrusion alarms, moisture or water ingress alarms, and personal safety devices.
LOW-POWER CMOS
ALARM IC
WITH HORN DRIVER
Features
•
•
•
•
•
•
•
•
•
•
•
High Impedance, FET Input Comparator
Comparator Outputs for Low Battery and Alarm Detect
Alarm Detect Threshold Easily Established with 2 Resistors
Integrated Oscillator and Piezoelectric Horn Driver
Low Battery Trip Point Set Internally (Altered Externally)
Horn “Chirp'' During Low Battery Condition
Pulsed LED Drive Output
P SUFFIX
ED SUFFIX (PB-FREE)
16-LEAD PLASTIC DIP
CASE 648-08
Reverse Battery Protection
Input Protection Diodes on the Detect Input
Average Supply Current: 9 μA
Pb-Free Packaging Designated by Suffix Codes ED and EG
DW SUFFIX
EG SUFFIX (PB-FREE)
16-LEAD SOIC
ORDERING INFORMATION
CASE 751G-04
Device
MC14600P
Case No.
Package
648-08
16 PDIP
16 SOIC
MC14600DW/R2
MCZ14600EG/R2
DETECT
GUARD
16
15
751G-04
1
2
3
4
5
6
7
8
COMP. OUT
16 SOIC (Pb-free)
ALARM
DETECT INPUT
N/C
14 N/C
LOW V SET
ALARM
THRESHOLD
LOW V
COMP. OUT
13
12 OSC CAPACITOR
LED
11 HORN OUT 2
VDD
TIMING
RESISTOR
HORN
HORN OUT 1
VSS
10
9
FEEDBACK
Figure 1. Pin Connections
Freescale Semiconductor, Inc. reserves the right to change the detail specifications,
as may be required, to permit improvements in the design of its products.
© Freescale Semiconductor, Inc., 2007. All rights reserved.
Archived by Freescale Semiconductor, Inc., 2009
VDD VDD
LOW V COMP.
HORN FEEDBACK
8
OUT
4
HORN
OUT 2
11
10
Low Battery
-
+
Comparator
3
1
LOW V SET
DETECT
COMPARATOR
OUT
HORN
OUT 1
Alarm
13
ALARM
Detect
-
+
THRESHOLD
Comparator
ALARM
DETECT
INPUT
15
OSC &
Timing
5
Guard
Amp
LED
VDD
VDD HI-Z
16
+
-
VDD = Pin 6
VSS = Pin 9
COSC
12
RBIAS
7
Figure 2. 14600 Block Diagram
Table 1. Maximum Ratings1
(Voltages referenced to VSS
)
Rating
Symbol
Value
Unit
DC Supply Voltage
VDD
-0.5 to +15
V
Input Voltage, All Inputs Except Pin 8
VIN
-0.25 to VDD +0.25
V
DC Current Drain per Input Pin Except Pin 15 = 1 mA
DC Current Drain per Output Pin
I
I
10
30
mA
mA
°C
Operating Temperature Range
TA
-10 to +60°C
Storage Temperature Range
Reverse Battery Time
TSTG
tRB
-55 to +125
5.0
°C
s
1. Maximum Ratings are those values beyond which damage to the device may occur.
This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised normal
precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. For proper
operation, it is recommended VIN and VOUT be constrained to the range VSS ≤ (VIN or VOUT) ≤ VDD
.
Table 2. Recommended Operating Conditions
(Voltages referenced to VSS
)
Parameter
Symbol
Value
9.0
Unit
V
Supply Voltage
VDD
LED Load (Pin 5)
—
10
mA
14600
Analog Integrated Circuit Device Data
Freescale Semiconductor
2
Archived by Freescale Semiconductor, Inc., 2009
Table 3. Electrical Characteristics
(Voltages referenced to V , T = 25°C)
CC
A
Typ1
V
/V
Characteristics
Symbol
Min
Max
Unit
DD DC
Operating Voltage
Output Voltage
VDD
—
6.0
—
12
V
Piezoelectric Horn Drivers (IOH = +16 mA), Pins 10, 11
VOH
7.4
9.0
7.4
9.0
—
6.5
8.5
—
—
—
—
8.8
—
0.1
—
—
—
0.9
0.5
0.5
V
V
Comparators (IOH = +30 μA), Pin 4
Piezoelectric Horn Drivers (IOL = -16 mA), Pins 10, 11
Comparators (IOL = -30 μA), Pin 4
VOL
(IOL = -200 μA), Pin 1
Output Voltage — LED Driver, IOL = 10 mA, Pin 5
VOL
7.2
9.0
—
—
—
—
2.0
V
Output Impedance, Active Guard, Pin 16
HI-Z
1000
kΩ
Standby Current (RBIAS = 8.2 MΩ)
9.0
12.0
—
—
5.0
—
9.0
12.0
IDD
μA
Input Leakage Current
Pin 1
Pin 8
Pin 13
—
IIN
9.0
9.0
9.0
—
—
—
—
—
—
±30
±0.1
±30
nA
μA
nA
—
Detect Comparator Out , Pin 1
V = 3.0 V
V = 9.0 V
—
—
—
—
2.50
—
—
—
—
8.00
mA
mA
Low Battery Threshold Voltage (Pin 3 Open), Pin 6
VLOW
9.0
7.2
—
7.8
V
Offset Voltage (Measured at VIN = VDD/2)
VOS
9.0
9.0
—
—
—
—
±100
±50
mV
Active Guard
Detect Comparator
Input Voltage Range, Pin 8
VIN
CIN
VCM
—
VSS -10
VDD +10
—
—
—
—
—
5.0
—
V
pF
V
Input Capacities (to VSS @ 1 khz), Pin 15
Common Mode Voltage Range, Pins 13, 15
Breakdown Voltage, All Pins Except 15
—
1.5
—
VDD -2
—
±500
—
V
Human Body Models/MIL–STD–883 Method 3015, Pin 15
—
—
±400
—
—
1. Data labelled “Typ” is not to be used for design purposes, but is intended as an indication of the IC’s potential performance.
Table 4. Timing Parameters
(COSC = 0.1 μF, RBIAS = 8.2 MΩ, VDD = 9.0 V, TA = 25°C, see Figure 3.)
Characteristic
Pin #
Symbol
Min
Max
Units
Oscillator Period (1 Clock Cycle = 1 Oscillator Period)
No Alarm
Alarm
tCI
—
1.25
30
2.25
52
s
ms
12
3, 4, 5, 13
5
Oscillator Pulse Width (No Alarm and Alarm Condition)
LED Output Period
tr
7.0
13
ms
No Alarm
Alarm
tLED
—
30
.71
52
1.25
s
ms
Alarm Horn Output
Hi Time
Low Time
tON
120
60
208
104
ms
ms
10, 11
10, 11
tOFF
Low Battery Horn OutpuT
Hi Time
Between Pulses
tON
7.0
30
13
52
ms
s
tOFF
14600
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
Archived by Freescale Semiconductor, Inc., 2009
DEVICE OPERATION
Timing
The internal oscillator of the MC14600 operates with a
power strobed and thus gives constant protection from
surface leakage currents. Pin 15 (the Detect input) has
internal diode protection against static damage.
period of 1.65 seconds during no-alarm conditions. Each
1.65 seconds, internal power is applied to the entire IC and a
check is made for an alarm input level except during LED
pulse, Low Battery Alarm Chirp, or Horn Modulation (in
alarm). Every 24 clock cycles a check is made for low battery
by comparing VDD to an internal zener voltage. Since very
small currents are used in the oscillator, the oscillator
capacitor should be of a low leakage type.
Low Battery Threshold
The low battery voltage level is set internally by a voltage
divider connected between VDD and VSS. This voltage can
be altered by external resistors connected from pin 3 to either
VDD or VSS. A resistor to VDD will decrease the threshold
while a resistor to GND will increase it.
Alarm Threshold (Sensitivity)
Detect Circuitry
The alarm condition voltage level is set externally through
Pin 13. A voltage divider can be used to set the alarm trip
point. Pin 13 is connected internally to the negative input of
the detect comparator.
If an alarm condition is detected, the oscillator period
becomes 41.67 ms and the piezoelectric horn oscillator
circuit is enabled. The horn output is modulated 167 ms on,
83 ms off. During the off time, alarm detect input (Pin 15) is
again checked and will inhibit further horn output if no alarm
condition is sensed. During alarm conditions the low battery
chirp is inhibited, and the LED pulses at a 1.0 Hz rate.
An active guard is provided on a pin adjacent to the detect
input (Pin 16). The voltage at this pin will be within 100 mV of
the input signal. Pin 16 will allow monitoring of the input signal
at pin 15 through a buffer. The active guard op amp is not
.
LED Pulse
The 9-volt battery level is checked every 40 seconds
during the LED pulse. The battery is loaded via a 10 mA
pulse for 10 ms. If the LED is not used, it should be replaced
with an equivalent resistor so that the battery loading remains
at 10 mA.
VDD
RP
1
2
3
4
5
6
7
8
16
MC14600
DETECT
INPUT
15
14
13
12
11
10
9
VDD
R1
R2
VDD
330 Ω
COSC
RBIAS
0.1 μF
1.5 MΩ*
0.001 μF
220 kΩ*
*Note: Component values may change depending on the type of piezoelectric horn used.
Figure 3. Typical Application Components
14600
Analog Integrated Circuit Device Data
Freescale Semiconductor
4
Archived by Freescale Semiconductor, Inc., 2009
1
2
3
4
5
6
7
8
9
23 24
1
6
12
18
24
OSC Pin 12
OSC Pin 12
Alarm-N
-Y
Alarm-N
-Y
No Alarm, Low Battery
No Alarm
Alarm
No Alarm
No Low Bat
Latch Alarm Condition
LOW BATTERY
COMPARATOR
LOW BATTERY
COMPARATOR
(Pin 4)
DETECT OUT
(Pin 1)
DETECT OUT (Pin1)
(NOTE 1)
Low Battery Chirp >>
HORN - ON
(Pins 10 and 11)
HORN - ON
- OFF
LED - OFF
- ON
LED - OFF
- ON
24 Clocks
24 Clocks
Figure 4. MC14600 Timing Diagram
NOTE:
1. Horn modulation is self-completing. When going from Alarm to No Alarm, the alarm condition will terminate only when
horn is off.
2. Comparators are strobed once per cycle.
3. Low Battery comparator information is latched only during LED pulse.
4. Current source required into Pin 1.
5. Alarm Condition can initiate on any clock pulse except 1 and 7.
14600
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
Archived by Freescale Semiconductor, Inc., 2009
PACKAGING
PACKAGING
NOTES:
-A-
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
16
1
9
8
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
B
S
INCHES
MILLIMETERS
DIM MIN
MAX MIN MAX
0.770 18.80 19.55
F
A
B
C
D
F
0.740
0.250
0.145
0.015
0.040
C
L
0.270
0.175
0.021
0.70
6.35
3.69
0.39
1.02
6.85
4.44
0.53
1.77
SEATING
PLANE
-T-
G
H
J
K
L
0.100 BSC
0.050 BSC
2.54 BSC
1.27 BSC
M
K
0.008
0.015
0.130
0.305
10
0.21
0.38
3.30
7.74
10
H
J
0.110
0.295
0
2.80
7.50
0
G
D
16 PL
M
S
0.020
0.040
0.51
1.01
M
M
0.25 (0.010)
T
A
STYLE 1:
STYLE 2:
PIN 1. CATHODE
2. CATHODE
3. CATHODE
4. CATHODE
5. CATHODE
6. CATHODE
7. CATHODE
8. CATHODE
9. ANODE
PIN 1. COMMON DRAIN
2. COMMON DRAIN
3. COMMON DRAIN
4. COMMON DRAIN
5. COMMON DRAIN
6. COMMON DRAIN
7. COMMON DRAIN
8. COMMON DRAIN
9. GATE
10. ANODE
11. ANODE
12. ANODE
13. ANODE
14. ANODE
15. ANODE
16. ANODE
10. SOURCE
11. GATE
12. SOURCE
13. GATE
14. SOURCE
15. GATE
16. SOURCE
DATE 05/18/88
CASE 751G-04
ISSUE D
16-LEAD SOIC
14600
Analog Integrated Circuit Device Data
Freescale Semiconductor
6
Archived by Freescale Semiconductor, Inc., 2009
PACKAGING
M
0.25
B
2.65
2.35
A
0.25
0.10
10.55
10.05
8X
PIN'S
NUMBER
0.49
16X 0.35
0.25
6
M
16
T A B
1
PIN 1 INDEX
14X
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
10.45
10.15
1.27
4
A
2. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
3. DATUMS A AND B TO BE DETERMINED AT THE
PLANE WHERE THE BOTTOM OF THE LEADS
EXIT THE PLASTIC BODY.
A
8
9
4. THIS DIMENSION DOES NOT INCLUDE MOLD
FLASH, PROTRUSION OR GATE BURRS. MOLD
FLASH, PROTRUSTION OR GATE BURRS SHALL
NOT EXCEED 0.15mm PER SIDE. THIS
DIMENSION IS DETERMINED AT THE PLANE
WHERE THE BOTTOM OF THE LEADS EXIT
THE PLASTIC BODY.
5. THIS DIMENSION DOES NOT INCLUDE
INTER-LEAD FLASH OR PROTRUSIONS.
INTER-LEAD FLASH AND PROTRUSIONS
SHALL NOT EXCEED 0.25mm PER SIDE. THIS
DIMENSION IS DETERMINED AT THE PLANE
WHERE THE BOTTOM OF THE LEADS EXIT
THE PLASTIC BODY.
SEATING
PLANE
T
16X
7.6
7.4
B
0.1 T
5
0.75
˚
0.25 X45
0.32
0.23
6. THIS DIMENSION DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL NOT CAUSE
THE LEAD WIDTH TO EXCEED 0.62mm.
1.0
0.4
7˚
0˚
SECTION A-A
DATE 03/05/0
CASE 751G-04
ISSUE D
16-LEAD SOIC
14600
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
Archived by Freescale Semiconductor, Inc., 2009
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
support@freescale.com
For information on Freescale’s Environmental Products program, go to http://
www.freescale.com/epp.
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
support@freescale.com
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
support@freescale.com
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
support.asia@freescale.com
Semiconductor was negligent regarding the design or manufacture of the part.
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
Denver, Colorado 80217
© Freescale Semiconductor, Inc., 2007. All rights reserved.
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor@hibbertgroup.com
MC14600
Rev. 7.0
6/2007
相关型号:
©2020 ICPDF网 联系我们和版权申明