MKL15Z128VFT4 [NXP]
Kinetis L 32-bit MCU, ARM Cortex-M0+ core, 128KB Flash, 48MHz, QFN 48;型号: | MKL15Z128VFT4 |
厂家: | NXP |
描述: | Kinetis L 32-bit MCU, ARM Cortex-M0+ core, 128KB Flash, 48MHz, QFN 48 时钟 微控制器 外围集成电路 |
文件: | 总57页 (文件大小:1154K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Freescale Semiconductor, Inc.
Data Sheet: Technical Data
Document Number: KL15P80M48SF0
Rev 5 08/2014
Kinetis KL15 Sub-Family
MKL15ZxxVFM4
MKL15ZxxVFT4
MKL15ZxxVLH4
MKL15ZxxVLK4
48 MHz Cortex-M0+ Based Microcontroller
Designed with efficiency in mind. Compatible with all other
Kinetis L families as well as Kinetis K1x family. General purpose
MCU featuring market leading ultra low-power to provide
developers an appropriate entry-level 32-bit solution.
This product offers:
• Run power consumption down to 47 μA/MHz in very low
power run mode
32-pin QFN (FM)
5 x 5 x 1 Pitch 0.5 mm 7 x 7 x 1 Pitch 0.5 mm
48-pin QFN (FT)
• Static power consumption down to 2 μA with full state
retention and 4 μs wakeup
• Ultra-efficient Cortex-M0+ processor running up to 48MHz
with industry leading throughput
• Memory option is up to 128 KB flash and 16 KB RAM
• Energy-saving architecture is optimized for low power with
90 nm TFS technology, clock and power gating techniques,
and zero wait state flash memory controller
64-pin LQFP (LH)
10 x 10 x 1.4 Pitch 0.5 12 x 12 x 1.4 Pitch 0.5
mm mm
80-pin LQFP (LK)
Performance
• 48 MHz ARM® Cortex®-M0+ core
Human-machine interface
• Low-power hardware touch sensor interface (TSI)
• Up to 70 general-purpose input/output (GPIO)
Memories and memory interfaces
• Up to 128 KB program flash memory
• Up to 16 KB SRAM
Communication interfaces
• Two 8-bit SPI modules
• One low power UART module
• Two UART modules
System peripherals
• Nine low-power modes to provide power optimization
based on application requirements
• COP Software watchdog
• Two I2C module
Analog Modules
• 4-channel DMA controller, supporting up to 63 request
sources
• Low-leakage wakeup unit
• SWD debug interface and Micro Trace Buffer
• Bit Manipulation Engine
• 16-bit SAR ADC
• 12-bit DAC
• Analog comparator (CMP) containing a 6-bit DAC
and programmable reference input
Timers
Clocks
• Six channel Timer/PWM (TPM)
• Two 2-channel Timer/PWM modules
• Periodic interrupt timers
• 16-bit low-power timer (LPTMR)
• Real time clock
• 32 kHz to 40 kHz or 3 MHz to 32 MHz crystal oscillator
• Multi-purpose clock source
• 1 kHz LPO clock
Operating Characteristics
• Voltage range: 1.71 to 3.6 V
Security and integrity modules
• Flash write voltage range: 1.71 to 3.6 V
• Temperature range (ambient): -40 to 105°C
• 80-bit unique identification number per chip
Freescale reserves the right to change the detail specifications as may be required to
permit improvements in the design of its products. © 2012–2014 Freescale
Semiconductor, Inc. All rights reserved.
Ordering Information
Memory
Part Number
Maximum number of I\O's
Flash (KB)
SRAM (KB)
MKL15Z32VFM4
32
64
4
8
28
28
28
40
40
40
54
54
54
70
70
70
MKL15Z64VFM4
MKL15Z128VFM4
MKL15Z32VFT4
MKL15Z64VFT4
MKL15Z128VFT4
MKL15Z32VLH4
MKL15Z64VLH4
MKL15Z128VLH4
MKL15Z32VLK4
MKL15Z64VLK4
MKL15Z128VLK4
128
32
16
4
64
8
128
32
16
4
64
8
128
32
16
4
64
8
128
16
Related Resources
Type
Description
Resource
Selector Guide The Freescale Solution Advisor is a web-based tool that features
interactive application wizards and a dynamic product selector.
Solution Advisor
Product Brief
The Product Brief contains concise overview/summary information to KL1 Family Product Brief1
enable quick evaluation of a device for design suitability.
Reference
Manual
The Reference Manual contains a comprehensive description of the KL15P80M48SF0RM1
structure and function (operation) of a device.
Data Sheet
The Data Sheet includes electrical characteristics and signal
connections.
KL15P80M48SF01
Chip Errata
The chip mask set Errata provides additional or corrective
information for a particular device mask set.
KINETIS_L_xN97F2
Package
drawing
Package dimensions are provided in package drawings.
QFN 32-pin: 98ASA00473D1
QFN 48-pin: 98ASA00466D1
LQFP 64-pin: 98ASS23234W1
LQFP 80-pin: 98ASS23174W1
1. To find the associated resource, go to http://www.freescale.com and perform a search using this term.
2. To find the associated resource, go to http://www.freescale.com and perform a search using this term with the “x”
replaced by the revision of the device you are using.
Figure 1 shows the functional modules in the chip.
2
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Kinetis KL15 Family
Memories and
Memory Interfaces
System
Clocks
Cortex-M0+
Core
ARM
Phase-
locked loop
Internal
watchdog
Debug
Program
flash
interfaces
Frequency-
locked loop
DMA
BME
Interrupt
RAM
Low/high
frequency
oscillator
controller
MTB
Internal
reference
clocks
Security
and Integrity
Human-Machine
Interface (HMI)
Analog
Communication
Interfaces
Timers
Timers
1x6ch+2x2ch
16-bit ADC
x1
Internal
watchdog
I2C
x2
GPIOs
with
interrupt
Low
power timer
x1
Analog
comparator
x1
Low power
TSI
UART
x1
Periodic
interrupt
timers
6-bit DAC
SPI
x2
12-bit DAC
RTC
UART
x2
LEGEND
Migration difference from KL05 family
Figure 1. Functional block diagram
Kinetis KL15 Sub-Family, Rev5 08/2014.
3
Freescale Semiconductor, Inc.
Table of Contents
1 Ratings....................................................................................5
3.6.2 CMP and 6-bit DAC electrical specifications....... 31
3.6.3 12-bit DAC electrical characteristics....................32
3.7 Timers..............................................................................35
3.8 Communication interfaces............................................... 35
3.8.1 SPI switching specifications................................ 35
3.8.2 Inter-Integrated Circuit Interface (I2C) timing...... 40
3.8.3 UART...................................................................41
3.9 Human-machine interfaces (HMI)....................................41
3.9.1 TSI electrical specifications................................. 41
4 Dimensions............................................................................. 42
4.1 Obtaining package dimensions....................................... 42
5 Pinout......................................................................................42
5.1 KL15 Signal Multiplexing and Pin Assignments...............42
5.2 KL15 pinouts....................................................................45
6 Ordering parts......................................................................... 49
6.1 Determining valid orderable parts....................................49
7 Part identification.....................................................................49
7.1 Description.......................................................................50
7.2 Format............................................................................. 50
7.3 Fields............................................................................... 50
7.4 Example...........................................................................50
8 Terminology and guidelines.................................................... 51
8.1 Definition: Operating requirement....................................51
8.2 Definition: Operating behavior......................................... 51
8.3 Definition: Attribute.......................................................... 52
8.4 Definition: Rating............................................................. 52
8.5 Result of exceeding a rating............................................ 52
8.6 Relationship between ratings and operating
1.1 Thermal handling ratings................................................. 5
1.2 Moisture handling ratings................................................ 5
1.3 ESD handling ratings.......................................................5
1.4 Voltage and current operating ratings............................. 5
2 General................................................................................... 6
2.1 AC electrical characteristics.............................................6
2.2 Nonswitching electrical specifications..............................6
2.2.1 Voltage and current operating requirements....... 7
2.2.2 LVD and POR operating requirements................7
2.2.3 Voltage and current operating behaviors.............8
2.2.4 Power mode transition operating behaviors........ 9
2.2.5 Power consumption operating behaviors............ 10
2.2.6 EMC radiated emissions operating behaviors.....15
2.2.7 Designing with radiated emissions in mind..........16
2.2.8 Capacitance attributes.........................................16
2.3 Switching specifications...................................................16
2.3.1 Device clock specifications..................................16
2.3.2 General switching specifications......................... 17
2.4 Thermal specifications.....................................................17
2.4.1 Thermal operating requirements......................... 17
2.4.2 Thermal attributes................................................18
3 Peripheral operating requirements and behaviors.................. 18
3.1 Core modules.................................................................. 18
3.1.1 SWD electricals .................................................. 18
3.2 System modules.............................................................. 20
3.3 Clock modules................................................................. 20
3.3.1 MCG specifications..............................................20
3.3.2 Oscillator electrical specifications........................22
3.4 Memories and memory interfaces................................... 24
3.4.1 Flash electrical specifications..............................24
3.5 Security and integrity modules........................................ 26
3.6 Analog............................................................................. 26
3.6.1 ADC electrical specifications............................... 26
requirements....................................................................53
8.7 Guidelines for ratings and operating requirements..........53
8.8 Definition: Typical value...................................................54
8.9 Typical value conditions.................................................. 55
9 Revision history.......................................................................55
4
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Ratings
1 Ratings
1.1 Thermal handling ratings
Table 1. Thermal handling ratings
Symbol
TSTG
Description
Min.
–55
—
Max.
150
Unit
°C
Notes
Storage temperature
Solder temperature, lead-free
1
2
TSDR
260
°C
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
1.2 Moisture handling ratings
Table 2. Moisture handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
MSL
Moisture sensitivity level
—
3
—
1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
1.3 ESD handling ratings
Table 3. ESD handling ratings
Symbol
VHBM
Description
Min.
–2000
–500
Max.
+2000
+500
Unit
V
Notes
Electrostatic discharge voltage, human body model
1
2
VCDM
Electrostatic discharge voltage, charged-device
model
V
ILAT
Latch-up current at ambient temperature of 105 °C
–100
+100
mA
3
1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human
Body Model (HBM).
2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for
Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components.
3. Determined according to JEDEC Standard JESD78, IC Latch-Up Test.
Kinetis KL15 Sub-Family, Rev5 08/2014.
5
Freescale Semiconductor, Inc.
General
1.4 Voltage and current operating ratings
Table 4. Voltage and current operating ratings
Symbol
VDD
IDD
Description
Min.
–0.3
—
Max.
3.8
Unit
V
Digital supply voltage
Digital supply current
IO pin input voltage
120
mA
V
VIO
–0.3
–25
VDD + 0.3
25
ID
Instantaneous maximum current single pin limit (applies to
all port pins)
mA
VDDA
Analog supply voltage
VDD – 0.3
VDD + 0.3
V
2 General
2.1 AC electrical characteristics
Unless otherwise specified, propagation delays are measured from the 50% to the 50%
point, and rise and fall times are measured at the 20% and 80% points, as shown in the
following figure.
High
Low
VIH
80%
50%
20%
Input Signal
Midpoint1
VIL
Fall Time
Rise Time
The midpoint is VIL + (VIH - VIL) / 2
Figure 2. Input signal measurement reference
All digital I/O switching characteristics, unless otherwise specified, assume the output
pins have the following characteristics.
• CL=30 pF loads
• Slew rate disabled
• Normal drive strength
2.2 Nonswitching electrical specifications
6
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
General
2.2.1 Voltage and current operating requirements
Table 5. Voltage and current operating requirements
Symbol
VDD
Description
Min.
1.71
1.71
–0.1
–0.1
Max.
3.6
Unit
V
Notes
Supply voltage
VDDA
Analog supply voltage
3.6
V
—
—
—
—
VDD – VDDA VDD-to-VDDA differential voltage
VSS – VSSA VSS-to-VSSA differential voltage
0.1
V
0.1
V
VIH
Input high voltage
• 2.7 V ≤ VDD ≤ 3.6 V
• 1.7 V ≤ VDD ≤ 2.7 V
0.7 × VDD
—
—
V
V
0.75 × VDD
VIL
Input low voltage
—
• 2.7 V ≤ VDD ≤ 3.6 V
• 1.7 V ≤ VDD ≤ 2.7 V
—
—
0.35 × VDD
0.3 × VDD
V
V
VHYS
IICIO
Input hysteresis
0.06 × VDD
–3
—
—
V
—
1
IO pin negative DC injection current—single pin
• VIN < VSS–0.3V
mA
IICcont
Contiguous pin DC injection current —regional limit,
includes sum of negative injection currents of 16
contiguous pins
—
–25
—
mA
• Negative current injection
VODPU
VRAM
Open drain pullup voltage level
VDD
1.2
VDD
—
V
V
2
VDD voltage required to retain RAM
—
1. All I/O pins are internally clamped to VSS through a ESD protection diode. There is no diode connection to VDD. If VIN
greater than VIO_MIN (= VSS-0.3 V) is observed, then there is no need to provide current limiting resistors at the pads. If
this limit cannot be observed then a current limiting resistor is required. The negative DC injection current limiting
resistor is calculated as R = (VIO_MIN - VIN)/|IICIO|.
2. Open drain outputs must be pulled to VDD
.
2.2.2 LVD and POR operating requirements
Table 6. VDD supply LVD and POR operating requirements
Symbol Description
Min.
0.8
Typ.
1.1
Max.
1.5
Unit
V
Notes
—
VPOR
Falling VDD POR detect voltage
VLVDH
Falling low-voltage detect threshold — high
range (LVDV = 01)
2.48
2.56
2.64
V
—
Low-voltage warning thresholds — high range
1
Table continues on the next page...
Kinetis KL15 Sub-Family, Rev5 08/2014.
7
Freescale Semiconductor, Inc.
General
Table 6. VDD supply LVD and POR operating requirements (continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
VLVW1H
VLVW2H
VLVW3H
VLVW4H
• Level 1 falling (LVWV = 00)
• Level 2 falling (LVWV = 01)
• Level 3 falling (LVWV = 10)
• Level 4 falling (LVWV = 11)
2.62
2.70
2.78
V
2.72
2.82
2.92
2.80
2.90
3.00
2.88
2.98
3.08
V
V
V
VHYSH
VLVDL
Low-voltage inhibit reset/recover hysteresis —
high range
—
60
—
mV
V
—
—
1
Falling low-voltage detect threshold — low
range (LVDV=00)
1.54
1.60
1.66
Low-voltage warning thresholds — low range
• Level 1 falling (LVWV = 00)
VLVW1L
VLVW2L
VLVW3L
VLVW4L
1.74
1.84
1.94
2.04
—
1.80
1.90
2.00
2.10
40
1.86
1.96
2.06
2.16
—
V
V
• Level 2 falling (LVWV = 01)
• Level 3 falling (LVWV = 10)
V
• Level 4 falling (LVWV = 11)
V
VHYSL
Low-voltage inhibit reset/recover hysteresis —
low range
mV
—
VBG
tLPO
Bandgap voltage reference
0.97
900
1.00
1.03
V
—
—
Internal low power oscillator period — factory
trimmed
1000
1100
μs
1. Rising thresholds are falling threshold + hysteresis voltage
2.2.3 Voltage and current operating behaviors
Table 7. Voltage and current operating behaviors
Symbol
Description
Min.
Max.
Unit
Notes
VOH
Output high voltage — Normal drive pad (except
RESET)
1, 2
VDD – 0.5
VDD – 0.5
—
—
V
V
• 2.7 V ≤ VDD ≤ 3.6 V, IOH = –5 mA
• 1.71 V ≤ VDD ≤ 2.7 V, IOH = –1.5 mA
VOH
Output high voltage — High drive pad (except
RESET)
1, 2
VDD – 0.5
VDD – 0.5
—
—
V
V
• 2.7 V ≤ VDD ≤ 3.6 V, IOH = –18 mA
• 1.71 V ≤ VDD ≤ 2.7 V, IOH = –6 mA
IOHT
VOL
Output high current total for all ports
Output low voltage — Normal drive pad
• 2.7 V ≤ VDD ≤ 3.6 V, IOL = 5 mA
• 1.71 V ≤ VDD ≤ 2.7 V, IOL = 1.5 mA
—
100
mA
—
1
—
—
0.5
0.5
V
V
Table continues on the next page...
8
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
General
Table 7. Voltage and current operating behaviors (continued)
Symbol
Description
Min.
Max.
Unit
Notes
VOL
Output low voltage — High drive pad
• 2.7 V ≤ VDD ≤ 3.6 V, IOL = 18 mA
• 1.71 V ≤ VDD ≤ 2.7 V, IOL = 6 mA
1
—
—
—
—
0.5
0.5
100
1
V
V
IOLT
IIN
Output low current total for all ports
mA
μA
—
3
Input leakage current (per pin) for full temperature
range
IIN
IIN
Input leakage current (per pin) at 25 °C
—
—
0.025
65
μA
μA
3
3
Input leakage current (total all pins) for full
temperature range
IOZ
RPU
RPD
Hi-Z (off-state) leakage current (per pin)
Internal pullup resistors
—
20
20
1
μA
kΩ
kΩ
—
4
50
50
Internal pulldown resistors
5
1. PTB0, PTB1, PTD6, and PTD7 I/O have both high drive and normal drive capability selected by the associated
PTx_PCRn[DSE] control bit. All other GPIOs are normal drive only.
2. The reset pin only contains an active pull down device when configured as the RESET signal or as a GPIO. When
configured as a GPIO output, it acts as a pseudo open drain output.
3. Measured at VDD = 3.6 V
4. Measured at VDD supply voltage = VDD min and Vinput = VSS
5. Measured at VDD supply voltage = VDD min and Vinput = VDD
2.2.4 Power mode transition operating behaviors
All specifications except tPOR and VLLSx→RUN recovery times in the following
table assume this clock configuration:
• CPU and system clocks = 48 MHz
• Bus and flash clock = 24 MHz
• FEI clock mode
POR and VLLSx→RUN recovery use FEI clock mode at the default CPU and system
frequency of 21 MHz, and a bus and flash clock frequency of 10.5 MHz.
Table 8. Power mode transition operating behaviors
Symbol Description
Min.
Typ.
Max.
Unit
tPOR
After a POR event, amount of time from the
—
—
300
μs
1
point VDD reaches 1.8 V to execution of the first
instruction across the operating temperature
range of the chip.
• VLLS0 → RUN
—
95
115
μs
Table continues on the next page...
Kinetis KL15 Sub-Family, Rev5 08/2014.
9
Freescale Semiconductor, Inc.
General
Table 8. Power mode transition operating behaviors (continued)
Symbol Description
Min.
Typ.
93
42
4
Max.
115
53
Unit
• VLLS1 → RUN
—
μs
• VLLS3 → RUN
• LLS → RUN
—
μs
—
4.6
4.4
4.4
μs
• VLPS → RUN
• STOP → RUN
—
4
μs
—
4
μs
1. Normal boot (FTFA_FOPT[LPBOOT]=11).
2.2.5 Power consumption operating behaviors
The maximum values stated in the following table represent characterized results
equivalent to the mean plus three times the standard deviation (mean + 3 sigma).
Table 9. Power consumption operating behaviors
Symbol
IDDA
Description
Temp.
—
Typ.
—
Max
See note
—
Unit
mA
mA
Note
Analog supply current
1
2
IDD_RUNCO_ CM
Run mode current in compute operation
- 48 MHz core / 24 MHz flash/ bus
disabled, LPTMR running using 4 MHz
internal reference clock, CoreMark®
benchmark code executing from flash,
at 3.0 V
—
6.4
IDD_RUNCO
Run mode current in compute operation
- 48 MHz core / 24 MHz flash / bus
clock disabled, code of while(1) loop
executing from flash, at 3.0 V
—
—
3.9
5
4.8
5.9
mA
mA
3
3
IDD_RUN
Run mode current - 48 MHz core / 24
MHz bus and flash, all peripheral clocks
disabled, code executing from flash, at
3.0 V
IDD_RUN
Run mode current - 48 MHz core / 24
MHz bus and flash, all peripheral clocks
enabled, code executing from flash, at
3.0 V
at 25 °C
6.2
6.8
6.5
7.1
mA
mA
3, 4
at 125 °C
Table continues on the next page...
10
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
General
Table 9. Power consumption operating behaviors (continued)
Symbol
Description
Temp.
Typ.
Max
Unit
Note
IDD_WAIT
Wait mode current - core disabled / 48
MHz system / 24 MHz bus / flash
disabled (flash doze enabled), all
peripheral clocks disabled, at 3.0 V
—
3.1
3.8
mA
3
IDD_WAIT
Wait mode current - core disabled / 24
MHz system / 24 MHz bus / flash
disabled (flash doze enabled), all
peripheral clocks disabled • at 3.0 V
—
2.4
3.2
mA
3
IDD_PSTOP2
Stop mode current with partial stop 2
clocking option - core and system
disabled / 10.5 MHz bus, at 3.0 V
—
—
1.6
2
mA
µA
3
5
IDD_VLPRCO _CM
Very-low-power run mode current in
compute operation - 4 MHz core / 0.8
MHz flash / bus clock disabled, LPTMR
running with 4 MHz internal reference
clock, CoreMark benchmark code
executing from flash, at 3.0 V
777
—
IDD_VLPRCO
IDD_VLPR
IDD_VLPR
IDD_VLPW
Very low power run mode current in
compute operation - 4 MHz core / 0.8
MHz flash / bus clock disabled, code
executing from flash, at 3.0 V
—
—
—
—
171
204
262
123
420
449
509
366
µA
µA
µA
µA
6
6
Very low power run mode current - 4
MHz core / 0.8 MHz bus and flash, all
peripheral clocks disabled, code
executing from flash, at 3.0 V
Very low power run mode current - 4
MHz core / 0.8 MHz bus and flash, all
peripheral clocks enabled, code
executing from flash, at 3.0 V
4, 6
6
Very low power wait mode current -
core disabled / 4 MHz system / 0.8
MHz bus / flash disabled (flash doze
enabled), all peripheral clocks disabled,
at 3.0 V
IDD_STOP
Stop mode current at 3.0 V
at 25 °C
at 50 °C
at 70 °C
at 85 °C
at 105 °C
at 25 °C
at 50 °C
at 70 °C
at 85 °C
at 105 °C
at 25 °C
at 50 °C
319
333
343
365
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
—
—
353
400
380
450
444
572
IDD_VLPS
Very-low-power stop mode current at
3.0 V
3.75
6.66
12.9
22.7
48.4
1.68
3.05
8.46
13.41
25.71
44.06
90.1
2.09
4.04
IDD_LLS
Low leakage stop mode current at 3.0
V
—
Table continues on the next page...
Kinetis KL15 Sub-Family, Rev5 08/2014.
11
Freescale Semiconductor, Inc.
General
Table 9. Power consumption operating behaviors (continued)
Symbol
Description
Temp.
at 70 °C
at 85 °C
at 105 °C
at 25 °C
at 50 °C
at 70 °C
at 85 °C
at 105 °C
at 25 °C
at 50 °C
at 70 °C
at 85 °C
at 105 °C
at 25 °C
at 50 °C
at 70 °C
at 85 °C
at 105 °C
at 25 °C
at 50 °C
at 70 °C
at 85 °C
at 105 °C
Typ.
5.71
10
Max
7.75
13.54
30.41
1.6
Unit
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
Note
22.4
1.22
2.25
4.21
7.37
16.6
0.58
1.26
2.53
4.74
11.4
0.31
0.99
2.25
4.46
11.13
0.12
0.8
IDD_VLLS3
IDD_VLLS1
IDD_VLLS0
IDD_VLLS0
Very low-leakage stop mode 3 current
at 3.0 V
—
2.31
5.44
9.44
21.76
0.94
1.31
3.33
6.1
Very low-leakage stop mode 1 current
at 3.0 V
—
—
7
15.27
0.65
1.43
3.01
5.83
14.99
0.47
1.24
2.81
5.62
14.78
Very low-leakage stop mode 0 current
(SMC_STOPCTRL[PORPO] = 0) at 3.0
V
Very low-leakage stop mode 0 current
(SMC_STOPCTRL[PORPO] = 1) at 3.0
V
2.06
4.27
10.93
1. The analog supply current is the sum of the active or disabled current for each of the analog modules on the device. See
each module's specification for its supply current.
2. MCG configured for PEE mode. CoreMark benchmark compiled using Keil 4.54 with optimization level 3, optimized for
time.
3. MCG configured for FEI mode.
4. Incremental current consumption from peripheral activity is not included.
5. MCG configured for BLPI mode. CoreMark benchmark compiled using IAR 6.40 with optimization level high, optimized
for balanced.
6. MCG configured for BLPI mode.
7. No brownout.
Table 10. Low power mode peripheral adders — typical value
Symbol
Description
Temperature (°C)
Unit
-40
25
50
70
85
105
IIREFSTEN4MHz
4 MHz internal reference clock (IRC) adder.
Measured by entering STOP or VLPS mode
with 4 MHz IRC enabled.
56
56
56
56
56
56
µA
Table continues on the next page...
12
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
General
Table 10. Low power mode peripheral adders — typical value (continued)
Symbol
Description
Temperature (°C)
Unit
-40
25
50
70
85
105
IIREFSTEN32KHz
32 kHz internal reference clock (IRC) adder.
Measured by entering STOP mode with the
32 kHz IRC enabled.
52
52
52
52
52
52
µA
IEREFSTEN4MHz
External 4 MHz crystal clock adder.
Measured by entering STOP or VLPS mode
with the crystal enabled.
206
228
237
245
251
258
µA
nA
IEREFSTEN32KHz
External 32 kHz crystal clock
adder by means of the
OSC0_CR[EREFSTEN and
EREFSTEN] bits. Measured
by entering all modes with the
crystal enabled.
VLLS1
VLLS3
LLS
440
440
490
510
510
22
490
490
490
560
560
22
540
540
540
560
560
22
560
560
560
560
560
22
570
570
570
610
610
22
580
580
680
680
680
22
VLPS
STOP
ICMP
CMP peripheral adder measured by placing
the device in VLLS1 mode with CMP enabled
using the 6-bit DAC and a single external
input for compare. Includes 6-bit DAC power
consumption.
µA
nA
IRTC
RTC peripheral adder measured by placing
the device in VLLS1 mode with external 32
kHz crystal enabled by means of the
RTC_CR[OSCE] bit and the RTC ALARM set
for 1 minute. Includes ERCLK32K (32 kHz
external crystal) power consumption.
432
66
357
66
388
66
475
66
532
66
810
66
IUART
UART peripheral adder
measured by placing the
device in STOP or VLPS
mode with selected clock
source waiting for RX data at
115200 baud rate. Includes
selected clock source power
consumption.
MCGIRCLK
(4 MHz
internal
reference
clock)
µA
OSCERCLK
(4 MHz
external
crystal)
214
86
237
86
246
86
254
86
260
86
268
86
ITPM
TPM peripheral adder
MCGIRCLK
(4 MHz
internal
reference
clock)
µA
measured by placing the
device in STOP or VLPS
mode with selected clock
source configured for output
compare generating 100 Hz
clock signal. No load is
placed on the I/O generating
the clock signal. Includes
selected clock source and I/O
switching currents.
OSCERCLK
(4 MHz
external
crystal)
235
256
265
274
280
287
IBG
Bandgap adder when BGEN bit is set and
device is placed in VLPx, LLS, or VLLSx
mode.
45
45
45
45
45
45
µA
µA
IADC
ADC peripheral adder combining the
366
366
366
366
366
366
measured values at VDD and VDDA by placing
Kinetis KL15 Sub-Family, Rev5 08/2014.
13
Freescale Semiconductor, Inc.
General
Table 10. Low power mode peripheral adders — typical value
Symbol
Description
Temperature (°C)
50 70
Unit
-40
25
85
105
the device in STOP or VLPS mode. ADC is
configured for low power mode using the
internal clock and continuous conversions.
2.2.5.1 Diagram: Typical IDD_RUN operating behavior
The following data was measured under these conditions:
• MCG in FBE for run mode, and BLPE for VLPR mode
• No GPIOs toggled
• Code execution from flash with cache enabled
• For the ALLOFF curve, all peripheral clocks are disabled except FTFA
Run Mode Current Vs Core Frequency
Temperature = 25, VDD = 3, CACHE = Enable, Code Residence = Flash, Clocking Mode = FBE
8.00E-03
7.00E-03
6.00E-03
5.00E-03
4.00E-03
3.00E-03
2.00E-03
1.00E-03
000.00E+00
All Peripheral CLK Gates
All On
CLK Ratio
'1-2
'1-1
1
'1-1
2
'1-1
3
'1-1
4
'1-1
6
'1-1
12
'1-1
24
Flash-Core
Core Freq (MHz)
48
Figure 3. Run mode supply current vs. core frequency
14
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
General
400.00E-06
350.00E-06
300.00E-06
250.00E-06
200.00E-06
150.00E-06
100.00E-06
50.00E-06
All Off
All On
000.00E+00
CLK Ratio
Flash-Core
Core Freq (MHz)
1
2
4
Figure 4. VLPR mode current vs. core frequency
2.2.6 EMC radiated emissions operating behaviors
Table 11. EMC radiated emissions operating behaviors for 64-pin LQFP
package
Symbol
Description
Frequency
band
Typ.
Unit
Notes
(MHz)
VRE1
VRE2
Radiated emissions voltage, band 1
Radiated emissions voltage, band 2
Radiated emissions voltage, band 3
Radiated emissions voltage, band 4
IEC level
0.15–50
50–150
13
15
12
7
dBμV
dBμV
dBμV
dBμV
—
1, 2
VRE3
150–500
500–1000
0.15–1000
VRE4
VRE_IEC
M
2, 3
1. Determined according to IEC Standard 61967-1, Integrated Circuits - Measurement of Electromagnetic Emissions,
150 kHz to 1 GHz Part 1: General Conditions and Definitions and IEC Standard 61967-2, Integrated Circuits -
Measurement of Electromagnetic Emissions, 150 kHz to 1 GHz Part 2: Measurement of Radiated Emissions—TEM
Cell and Wideband TEM Cell Method. Measurements were made while the microcontroller was running basic
Kinetis KL15 Sub-Family, Rev5 08/2014.
15
Freescale Semiconductor, Inc.
General
application code. The reported emission level is the value of the maximum measured emission, rounded up to the next
whole number, from among the measured orientations in each frequency range.
2. VDD = 3.3 V, TA = 25 °C, fOSC = 8 MHz (crystal), fSYS = 48 MHz, fBUS = 48 MHz
3. Specified according to Annex D of IEC Standard 61967-2, Measurement of Radiated Emissions—TEM Cell and
Wideband TEM Cell Method
2.2.7 Designing with radiated emissions in mind
To find application notes that provide guidance on designing your system to minimize
interference from radiated emissions:
1. Go to www.freescale.com.
2. Perform a keyword search for “EMC design.”
2.2.8 Capacitance attributes
Table 12. Capacitance attributes
Symbol
Description
Min.
Max.
Unit
CIN
Input capacitance
—
7
pF
2.3 Switching specifications
2.3.1 Device clock specifications
Table 13. Device clock specifications
Symbol
Description
Min.
Max.
Unit
Normal run mode
fSYS
fBUS
fFLASH
fLPTMR
System and core clock
Bus clock
—
—
—
—
48
24
24
24
MHz
MHz
MHz
MHz
Flash clock
LPTMR clock
VLPR and VLPS modes1
fSYS
fBUS
System and core clock
Bus clock
—
—
—
—
—
4
1
MHz
MHz
MHz
MHz
MHz
fFLASH
fLPTMR
fERCLK
Flash clock
LPTMR clock2
1
24
16
External reference clock
Table continues on the next page...
16
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
General
Table 13. Device clock specifications (continued)
Symbol
Description
Min.
—
Max.
16
Unit
MHz
MHz
fLPTMR_ERCLK LPTMR external reference clock
fosc_hi_2
Oscillator crystal or resonator frequency — high frequency
—
16
mode (high range) (MCG_C2[RANGE]=1x)
fTPM
TPM asynchronous clock
—
—
8
8
MHz
MHz
fUART0
UART0 asynchronous clock
1. The frequency limitations in VLPR and VLPS modes here override any frequency specification listed in the timing
specification for any other module. These same frequency limits apply to VLPS, whether VLPS was entered from RUN
or from VLPR.
2. The LPTMR can be clocked at this speed in VLPR or VLPS only when the source is an external pin.
2.3.2 General switching specifications
These general-purpose specifications apply to all signals configured for GPIO and
UART signals.
Table 14. General switching specifications
Description
Min.
Max.
Unit
Notes
GPIO pin interrupt pulse width (digital glitch filter disabled)
— Synchronous path
1.5
—
Bus clock
cycles
1
External RESET and NMI pin interrupt pulse width —
Asynchronous path
100
—
ns
2
GPIO pin interrupt pulse width — Asynchronous path
Port rise and fall time
16
—
—
ns
ns
2
3
36
1. The greater synchronous and asynchronous timing must be met.
2. This is the shortest pulse that is guaranteed to be recognized.
3. 75 pF load
2.4 Thermal specifications
2.4.1 Thermal operating requirements
Table 15. Thermal operating requirements
Symbol
TJ
Description
Min.
Max.
125
Unit
°C
Die junction temperature
Ambient temperature
–40
–40
TA
105
°C
Kinetis KL15 Sub-Family, Rev5 08/2014.
17
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
2.4.2 Thermal attributes
Table 16. Thermal attributes
Board type
Symbol
Description
80
64
48 QFN 32 QFN
Unit
Notes
LQFP
LQFP
Single-layer (1S)
RθJA
Thermal resistance, junction
to ambient (natural
convection)
70
53
—
—
71
52
59
46
84
28
69
22
92
33
75
27
°C/W
1
Four-layer (2s2p)
Single-layer (1S)
Four-layer (2s2p)
RθJA
Thermal resistance, junction
to ambient (natural
convection)
°C/W
°C/W
°C/W
RθJMA Thermal resistance, junction
to ambient (200 ft./min. air
speed)
RθJMA Thermal resistance, junction
to ambient (200 ft./min. air
speed)
—
—
—
RθJB
RθJC
ΨJT
Thermal resistance, junction
to board
34
15
34
20
5
10
2.0
5.0
12
1.8
8
°C/W
°C/W
°C/W
2
3
4
Thermal resistance, junction
to case
Thermal characterization
parameter, junction to
package top outside center
(natural convection)
0.6
1. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air), or EIA/JEDEC Standard JESD51-6, Integrated Circuit Thermal Test Method
Environmental Conditions—Forced Convection (Moving Air).
2. Determined according to JEDEC Standard JESD51-8, Integrated Circuit Thermal Test Method Environmental
Conditions—Junction-to-Board.
3. Determined according to Method 1012.1 of MIL-STD 883, Test Method Standard, Microcircuits, with the cold plate
temperature used for the case temperature. The value includes the thermal resistance of the interface material between
the top of the package and the cold plate.
4. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air).
3 Peripheral operating requirements and behaviors
3.1 Core modules
18
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
3.1.1 SWD electricals
Table 17. SWD full voltage range electricals
Symbol
Description
Min.
Max.
Unit
Operating voltage
1.71
3.6
V
J1
SWD_CLK frequency of operation
• Serial wire debug
0
25
—
MHz
ns
J2
J3
SWD_CLK cycle period
SWD_CLK clock pulse width
• Serial wire debug
1/J1
20
—
ns
J4
J9
SWD_CLK rise and fall times
—
10
0
3
ns
ns
ns
ns
ns
SWD_DIO input data setup time to SWD_CLK rise
SWD_DIO input data hold time after SWD_CLK rise
SWD_CLK high to SWD_DIO data valid
SWD_CLK high to SWD_DIO high-Z
—
—
32
—
J10
J11
J12
—
5
J2
J4
J3
J3
SWD_CLK (input)
J4
Figure 5. Serial wire clock input timing
Kinetis KL15 Sub-Family, Rev5 08/2014.
19
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
SWD_CLK
SWD_DIO
J9
J10
Input data valid
J11
Output data valid
SWD_DIO
J12
SWD_DIO
J11
Output data valid
SWD_DIO
Figure 6. Serial wire data timing
3.2 System modules
There are no specifications necessary for the device's system modules.
3.3 Clock modules
3.3.1 MCG specifications
Table 18. MCG specifications
Symbol Description
Min.
Typ.
Max.
Unit
Notes
fints_ft Internal reference frequency (slow clock) —
—
32.768
—
kHz
factory trimmed at nominal VDD and 25 °C
fints_t
Internal reference frequency (slow clock) —
user trimmed
31.25
—
—
39.0625
0.6
kHz
Δfdco_res_t Resolution of trimmed average DCO output
frequency at fixed voltage and temperature —
using C3[SCTRIM] and C4[SCFTRIM]
0.3
%fdco
1
Table continues on the next page...
20
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 18. MCG specifications (continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
Δfdco_t
Total deviation of trimmed average DCO output
frequency over voltage and temperature
—
+0.5/-0.7
3
%fdco
1, 2
Δfdco_t
Total deviation of trimmed average DCO output
frequency over fixed voltage and temperature
range of 0–70 °C
—
0.4
1.5
%fdco
1, 2
fintf_ft
Internal reference frequency (fast clock) —
factory trimmed at nominal VDD and 25 °C
—
—
4
—
3
MHz
Δfintf_ft
Frequency deviation of internal reference clock
(fast clock) over temperature and voltage —
factory trimmed at nominal VDD and 25 °C
+1/-2
%fintf_ft
2
fintf_t
Internal reference frequency (fast clock) — user
trimmed at nominal VDD and 25 °C
3
—
—
—
5
MHz
kHz
kHz
floc_low
Loss of external clock minimum frequency —
RANGE = 00
(3/5) x
fints_t
—
—
floc_high Loss of external clock minimum frequency —
RANGE = 01, 10, or 11
(16/5) x
fints_t
FLL
ffll_ref
fdco
FLL reference frequency range
31.25
20
—
39.0625
25
kHz
DCO output
Low range (DRS = 00)
20.97
MHz
3, 4
5, 6
frequency range
640 × ffll_ref
Mid range (DRS = 01)
1280 × ffll_ref
40
—
—
—
—
41.94
23.99
47.97
180
48
—
—
—
1
MHz
MHz
MHz
ps
fdco_t_DMX3 DCO output
Low range (DRS = 00)
732 × ffll_ref
frequency
2
Mid range (DRS = 01)
1464 × ffll_ref
Jcyc_fll
FLL period jitter
• fVCO = 48 MHz
7
8
tfll_acquire FLL target frequency acquisition time
—
ms
PLL
fvco
Ipll
VCO operating frequency
48.0
—
—
100
—
MHz
µA
PLL operating current
9
9
1060
• PLL at 96 MHz (fosc_hi_1 = 8 MHz, fpll_ref
2 MHz, VDIV multiplier = 48)
=
Ipll
PLL operating current
—
600
—
—
µA
• PLL at 48 MHz (fosc_hi_1 = 8 MHz, fpll_ref
2 MHz, VDIV multiplier = 24)
=
fpll_ref
PLL reference frequency range
PLL period jitter (RMS)
• fvco = 48 MHz
2.0
4.0
MHz
Jcyc_pll
10
—
—
120
50
—
—
ps
ps
• fvco = 100 MHz
Table continues on the next page...
Kinetis KL15 Sub-Family, Rev5 08/2014.
21
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 18. MCG specifications (continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
Jacc_pll
PLL accumulated jitter over 1µs (RMS)
10
• fvco = 48 MHz
• fvco = 100 MHz
—
—
1350
600
—
—
ps
ps
Dlock
Dunl
Lock entry frequency tolerance
Lock exit frequency tolerance
Lock detector detection time
1.49
4.47
—
—
—
—
2.98
5.97
150 × 10-6
+ 1075(1/
%
%
s
tpll_lock
11
fpll_ref
)
1. This parameter is measured with the internal reference (slow clock) being used as a reference to the FLL (FEI clock
mode).
2. The deviation is relative to the factory trimmed frequency at nominal VDD and 25 °C, fints_ft
.
3. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32 = 0.
4. The resulting system clock frequencies must not exceed their maximum specified values. The DCO frequency deviation
(Δfdco_t) over voltage and temperature must be considered.
5. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32 = 1.
6. The resulting clock frequency must not exceed the maximum specified clock frequency of the device.
7. This specification is based on standard deviation (RMS) of period or frequency.
8. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed,
DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE,
FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running.
9. Excludes any oscillator currents that are also consuming power while PLL is in operation.
10. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise characteristics
of each PCB and results will vary.
11. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL
disabled (BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this
specification assumes it is already running.
3.3.2 Oscillator electrical specifications
3.3.2.1 Oscillator DC electrical specifications
Table 19. Oscillator DC electrical specifications
Symbol Description
Min.
Typ.
Max.
Unit
Notes
VDD
Supply voltage
1.71
—
3.6
V
IDDOSC
Supply current — low-power mode (HGO=0)
1
• 32 kHz
—
—
—
—
—
500
200
300
950
1.2
—
—
—
—
—
nA
μA
μA
μA
mA
• 4 MHz
• 8 MHz (RANGE=01)
• 16 MHz
Table continues on the next page...
22
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
Peripheral operating requirements and behaviors
Table 19. Oscillator DC electrical specifications (continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
• 24 MHz
—
1.5
—
mA
• 32 MHz
IDDOSC
Supply current — high gain mode (HGO=1)
1
• 32 kHz
—
—
—
—
—
—
25
400
500
2.5
3
—
—
—
—
—
—
μA
μA
• 4 MHz
• 8 MHz (RANGE=01)
• 16 MHz
μA
mA
mA
mA
• 24 MHz
• 32 MHz
4
Cx
Cy
RF
EXTAL load capacitance
XTAL load capacitance
—
—
—
—
—
—
—
—
—
2, 3
2, 3
2, 4
Feedback resistor — low-frequency, low-power
mode (HGO=0)
MΩ
MΩ
MΩ
MΩ
kΩ
Feedback resistor — low-frequency, high-gain
mode (HGO=1)
—
—
—
—
—
—
10
—
—
—
—
—
—
—
Feedback resistor — high-frequency, low-power
mode (HGO=0)
Feedback resistor — high-frequency, high-gain
mode (HGO=1)
1
RS
Series resistor — low-frequency, low-power
mode (HGO=0)
—
Series resistor — low-frequency, high-gain
mode (HGO=1)
200
—
kΩ
Series resistor — high-frequency, low-power
mode (HGO=0)
kΩ
Series resistor — high-frequency, high-gain
mode (HGO=1)
—
—
0
—
—
kΩ
V
5
Vpp
Peak-to-peak amplitude of oscillation (oscillator
mode) — low-frequency, low-power mode
(HGO=0)
0.6
Peak-to-peak amplitude of oscillation (oscillator
mode) — low-frequency, high-gain mode
(HGO=1)
—
—
—
VDD
0.6
—
—
—
V
V
V
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, low-power mode
(HGO=0)
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, high-gain mode
(HGO=1)
VDD
1. VDD=3.3 V, Temperature =25 °C
2. See crystal or resonator manufacturer's recommendation
Kinetis KL15 Sub-Family, Rev5 08/2014.
23
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
3. Cx,Cy can be provided by using the integrated capacitors when the low frequency oscillator (RANGE = 00) is used. For
all other cases external capacitors must be used.
4. When low power mode is selected, RF is integrated and must not be attached externally.
5. The EXTAL and XTAL pins should only be connected to required oscillator components and must not be connected to
any other devices.
3.3.2.2 Oscillator frequency specifications
Table 20. Oscillator frequency specifications
Symbol Description
fosc_lo Oscillator crystal or resonator frequency — low-
frequency mode (MCG_C2[RANGE]=00)
Min.
Typ.
Max.
Unit
Notes
32
—
40
kHz
fosc_hi_1 Oscillator crystal or resonator frequency — high-
frequency mode (low range)
3
8
—
—
8
MHz
MHz
(MCG_C2[RANGE]=01)
fosc_hi_2 Oscillator crystal or resonator frequency — high
frequency mode (high range)
32
(MCG_C2[RANGE]=1x)
fec_extal Input clock frequency (external clock mode)
tdc_extal Input clock duty cycle (external clock mode)
—
40
—
—
50
48
60
—
MHz
%
1, 2
3, 4
tcst
Crystal startup time — 32 kHz low-frequency,
low-power mode (HGO=0)
750
ms
Crystal startup time — 32 kHz low-frequency,
high-gain mode (HGO=1)
—
—
250
0.6
—
—
ms
ms
Crystal startup time — 8 MHz high-frequency
(MCG_C2[RANGE]=01), low-power mode
(HGO=0)
Crystal startup time — 8 MHz high-frequency
(MCG_C2[RANGE]=01), high-gain mode
(HGO=1)
—
1
—
ms
1. Other frequency limits may apply when external clock is being used as a reference for the FLL
2. When transitioning from FEI or FBI to FBE mode, restrict the frequency of the input clock so that, when it is divided by
FRDIV, it remains within the limits of the DCO input clock frequency.
3. Proper PC board layout procedures must be followed to achieve specifications.
4. Crystal startup time is defined as the time between the oscillator being enabled and the OSCINIT bit in the MCG_S
register being set.
3.4 Memories and memory interfaces
3.4.1 Flash electrical specifications
This section describes the electrical characteristics of the flash memory module.
24
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
3.4.1.1 Flash timing specifications — program and erase
The following specifications represent the amount of time the internal charge pumps
are active and do not include command overhead.
Table 21. NVM program/erase timing specifications
Symbol Description
Min.
—
Typ.
7.5
13
Max.
18
Unit
μs
Notes
thvpgm4 Longword Program high-voltage time
thversscr Sector Erase high-voltage time
—
1
—
113
452
ms
ms
thversall
Erase All high-voltage time
—
52
1
1. Maximum time based on expectations at cycling end-of-life.
3.4.1.2 Flash timing specifications — commands
Table 22. Flash command timing specifications
Symbol Description
Min.
—
—
—
—
—
—
—
—
—
—
Typ.
—
Max.
60
Unit
μs
Notes
trd1sec1k Read 1s Section execution time (flash sector)
tpgmchk Program Check execution time
1
1
—
45
μs
trdrsrc
tpgm4
tersscr
trd1all
trdonce
Read Resource execution time
Program Longword execution time
Erase Flash Sector execution time
Read 1s All Blocks execution time
Read Once execution time
—
30
μs
1
65
14
—
145
114
1.8
25
μs
—
2
ms
ms
μs
—
1
—
tpgmonce Program Once execution time
65
88
—
—
μs
—
2
tersall
Erase All Blocks execution time
650
30
ms
μs
tvfykey
Verify Backdoor Access Key execution time
1
1. Assumes 25 MHz flash clock frequency.
2. Maximum times for erase parameters based on expectations at cycling end-of-life.
3.4.1.3 Flash high voltage current behaviors
Table 23. Flash high voltage current behaviors
Symbol
Description
Min.
Typ.
Max.
Unit
IDD_PGM
Average current adder during high voltage
flash programming operation
—
2.5
6.0
mA
IDD_ERS
Average current adder during high voltage
flash erase operation
—
1.5
4.0
mA
Kinetis KL15 Sub-Family, Rev5 08/2014.
25
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
3.4.1.4 Reliability specifications
Table 24. NVM reliability specifications
Symbol Description
Min.
Program Flash
Typ.1
Max.
Unit
Notes
tnvmretp10k Data retention after up to 10 K cycles
tnvmretp1k Data retention after up to 1 K cycles
nnvmcycp Cycling endurance
5
50
—
—
—
years
years
cycles
—
—
2
20
100
50 K
10 K
1. Typical data retention values are based on measured response accelerated at high temperature and derated to a
constant 25 °C use profile. Engineering Bulletin EB618 does not apply to this technology. Typical endurance defined in
Engineering Bulletin EB619.
2. Cycling endurance represents number of program/erase cycles at -40 °C ≤ Tj ≤ 125 °C.
3.5 Security and integrity modules
There are no specifications necessary for the device's security and integrity modules.
3.6 Analog
3.6.1 ADC electrical specifications
The 16-bit accuracy specifications listed in Table 25 and Table 26 are achievable on the
differential pins ADCx_DP0, ADCx_DM0.
All other ADC channels meet the 13-bit differential/12-bit single-ended accuracy
specifications.
3.6.1.1 16-bit ADC operating conditions
Table 25. 16-bit ADC operating conditions
Symbol Description
Conditions
Min.
1.71
-100
-100
1.13
Typ.1
Max.
3.6
Unit
V
Notes
VDDA
ΔVDDA
ΔVSSA
VREFH
Supply voltage
Supply voltage
Absolute
—
—
2
Delta to VDD (VDD – VDDA
)
0
+100
+100
VDDA
mV
mV
V
Ground voltage Delta to VSS (VSS – VSSA
)
0
2
ADC reference
voltage high
VDDA
3
VREFL
ADC reference
voltage low
VSSA
VSSA
VSSA
V
3
Table continues on the next page...
26
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
Peripheral operating requirements and behaviors
Table 25. 16-bit ADC operating conditions (continued)
Symbol Description
Conditions
• 16-bit differential mode
Min.
Typ.1
Max.
Unit
Notes
VADIN
Input voltage
VREFL
—
31/32 *
VREFH
V
—
• All other modes
• 16-bit mode
VREFL
—
VREFH
CADIN
Input
capacitance
—
—
8
4
10
5
pF
—
• 8-bit / 10-bit / 12-bit
modes
RADIN
RAS
Input series
resistance
—
—
2
5
5
kΩ
kΩ
—
4
Analog source
resistance
(external)
13-bit / 12-bit modes
fADCK < 4 MHz
—
fADCK
fADCK
Crate
ADC conversion ≤ 13-bit mode
clock frequency
1.0
2.0
—
—
18.0
12.0
MHz
MHz
5
5
6
ADC conversion 16-bit mode
clock frequency
ADC conversion ≤ 13-bit modes
rate
No ADC hardware averaging
20.000
37.037
—
—
818.330
461.467
Ksps
Ksps
Continuous conversions
enabled, subsequent
conversion time
Crate
ADC conversion 16-bit mode
6
rate
No ADC hardware averaging
Continuous conversions
enabled, subsequent
conversion time
1. Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK = 1.0 MHz, unless otherwise stated. Typical values are for
reference only, and are not tested in production.
2. DC potential difference.
3. For packages without dedicated VREFH and VREFL pins, VREFH is internally tied to VDDA, and VREFL is internally tied
to VSSA
.
4. This resistance is external to MCU. To achieve the best results, the analog source resistance must be kept as low as
possible. The results in this data sheet were derived from a system that had < 8 Ω analog source resistance. The
RAS/CAS time constant should be kept to < 1 ns.
5. To use the maximum ADC conversion clock frequency, CFG2[ADHSC] must be set and CFG1[ADLPC] must be clear.
6. For guidelines and examples of conversion rate calculation, download the ADC calculator tool.
Kinetis KL15 Sub-Family, Rev5 08/2014.
27
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
SIMPLIFIED
INPUT PIN EQUIVALENT
CIRCUIT
ZADIN
SIMPLIFIED
CHANNEL SELECT
CIRCUIT
Pad
ZAS
leakage
due to
input
ADC SAR
ENGINE
RAS
RADIN
protection
VADIN
CAS
VAS
RADIN
RADIN
RADIN
INPUT PIN
INPUT PIN
INPUT PIN
CADIN
Figure 7. ADC input impedance equivalency diagram
3.6.1.2 16-bit ADC electrical characteristics
Table 26. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA
)
Symbol Description
Conditions1
Min.
0.215
1.2
Typ.2
Max.
1.7
3.9
6.1
7.3
9.5
Unit
mA
Notes
IDDA_ADC Supply current
—
3
ADC
asynchronous
clock source
• ADLPC = 1, ADHSC =
0
2.4
4.0
5.2
6.2
MHz
MHz
MHz
MHz
tADACK =
1/fADACK
2.4
• ADLPC = 1, ADHSC =
1
3.0
fADACK
4.4
• ADLPC = 0, ADHSC =
0
• ADLPC = 0, ADHSC =
1
Sample Time
See Reference Manual chapter for sample times
TUE
DNL
Total unadjusted
error
• 12-bit modes
• <12-bit modes
—
—
4
6.8
2.1
LSB4
LSB4
5
5
1.4
Differential non-
linearity
• 12-bit modes
• <12-bit modes
—
—
0.7
0.2
–1.1 to
+1.9
–0.3 to 0.5
Table continues on the next page...
28
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
Peripheral operating requirements and behaviors
Table 26. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Symbol Description
Conditions1
Min.
Typ.2
Max.
Unit
Notes
INL
Integral non-
linearity
• 12-bit modes
—
1.0
–2.7 to
+1.9
LSB4
5
• <12-bit modes
—
0.5
–0.7 to
+0.5
EFS
EQ
Full-scale error
• 12-bit modes
• <12-bit modes
• 16-bit modes
• ≤13-bit modes
—
—
—
—
–4
–1.4
–1 to 0
—
–5.4
–1.8
—
LSB4
LSB4
VADIN
VDDA
=
5
Quantization
error
0.5
ENOB
Effective number 16-bit differential mode
6
12.8
11.9
14.5
13.8
—
—
bits
bits
of bits
• Avg = 32
• Avg = 4
12.2
11.4
13.9
13.1
—
—
bits
bits
16-bit single-ended mode
• Avg = 32
• Avg = 4
Signal-to-noise
plus distortion
See ENOB
SINAD
THD
6.02 × ENOB + 1.76
dB
Total harmonic
distortion
16-bit differential mode
• Avg = 32
7
7
—
—
-94
-85
—
—
dB
dB
16-bit single-ended mode
• Avg = 32
SFDR
Spurious free
dynamic range
16-bit differential mode
• Avg = 32
82
78
95
90
—
—
dB
dB
16-bit single-ended mode
• Avg = 32
EIL
Input leakage
error
IIn × RAS
mV
IIn =
leakage
current
(refer to
the MCU's
voltage
and
current
operating
ratings)
Temp sensor
slope
Across the full temperature
range of the device
1.55
706
1.62
716
1.69
726
mV/°C
mV
8
VTEMP25 Temp sensor
voltage
25 °C
8
Kinetis KL15 Sub-Family, Rev5 08/2014.
29
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
1. All accuracy numbers assume the ADC is calibrated with VREFH = VDDA
2. Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK = 2.0 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
3. The ADC supply current depends on the ADC conversion clock speed, conversion rate and ADC_CFG1[ADLPC] (low
power). For lowest power operation, ADC_CFG1[ADLPC] must be set, the ADC_CFG2[ADHSC] bit must be clear with 1
MHz ADC conversion clock speed.
4. 1 LSB = (VREFH - VREFL)/2N
5. ADC conversion clock < 16 MHz, Max hardware averaging (AVGE = %1, AVGS = %11)
6. Input data is 100 Hz sine wave. ADC conversion clock < 12 MHz.
7. Input data is 1 kHz sine wave. ADC conversion clock < 12 MHz.
8. ADC conversion clock < 3 MHz
Typical ADC 16-bit Differential ENOB vs ADC Clock
100Hz, 90% FS Sine Input
15.00
14.70
14.40
14.10
13.80
13.50
13.20
12.90
12.60
Hardware Averaging Disabled
Averaging of 4 samples
12.30
12.00
Averaging of 8 samples
Averaging of 32 samples
1
2
3
4
5
6
7
8
9
10
11
12
ADC Clock Frequency (MHz)
Figure 8. Typical ENOB vs. ADC_CLK for 16-bit differential mode
Typical ADC 16-bit Single-Ended ENOB vs ADC Clock
100Hz, 90% FS Sine Input
14.00
13.75
13.50
13.25
13.00
12.75
12.50
12.25
12.00
11.75
11.50
11.25
11.00
Averaging of 4 samples
Averaging of 32 samples
1
2
3
4
5
6
7
8
9
10
11
12
ADC Clock Frequency (MHz)
Figure 9. Typical ENOB vs. ADC_CLK for 16-bit single-ended mode
30
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
3.6.2 CMP and 6-bit DAC electrical specifications
Table 27. Comparator and 6-bit DAC electrical specifications
Symbol
VDD
Description
Min.
1.71
—
Typ.
—
Max.
3.6
Unit
V
Supply voltage
IDDHS
Supply current, high-speed mode (EN = 1, PMODE
= 1)
—
200
μA
IDDLS
Supply current, low-speed mode (EN = 1, PMODE =
0)
—
—
20
μA
VAIN
VAIO
VH
Analog input voltage
VSS
—
—
—
VDD
20
V
Analog input offset voltage
Analog comparator hysteresis1
• CR0[HYSTCTR] = 00
• CR0[HYSTCTR] = 01
• CR0[HYSTCTR] = 10
• CR0[HYSTCTR] = 11
mV
—
—
—
—
5
—
—
—
—
mV
mV
mV
mV
10
20
30
VCMPOh
VCMPOl
tDHS
Output high
Output low
VDD – 0.5
—
—
50
—
0.5
200
V
V
—
Propagation delay, high-speed mode (EN = 1,
PMODE = 1)
20
ns
tDLS
Propagation delay, low-speed mode (EN = 1,
PMODE = 0)
80
250
600
ns
Analog comparator initialization delay2
6-bit DAC current adder (enabled)
6-bit DAC integral non-linearity
—
—
—
7
40
—
μs
μA
LSB3
IDAC6b
INL
–0.5
–0.3
—
—
0.5
0.3
DNL
6-bit DAC differential non-linearity
LSB
1. Typical hysteresis is measured with input voltage range limited to 0.7 to VDD – 0.7 V.
2. Comparator initialization delay is defined as the time between software writes to change control inputs (writes to
DACEN, VRSEL, PSEL, MSEL, VOSEL) and the comparator output settling to a stable level.
3. 1 LSB = Vreference/64
Kinetis KL15 Sub-Family, Rev5 08/2014.
31
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
CMP Hysteresis vs Vinn
90.00E-03
80.00E-03
70.00E-03
60.00E-03
50.00E-03
40.00E-03
30.00E-03
20.00E-03
10.00E-03
000.00E+00
HYSTCTR
Setting
0
1
2
3
0.1
0.4
0.7
1
1.3
1.6
1.9
2.2
2.5
2.8
3.1
Vinn (V)
Figure 10. Typical hysteresis vs. Vin level (VDD = 3.3 V, PMODE = 0)
CMP Hysteresis vs Vinn
180.00E-03
160.00E-03
140.00E-03
120.00E-03
HYSTCTR
Setting
100.00E-03
0
80.00E-03
60.00E-03
40.00E-03
20.00E-03
000.00E+00
-20.00E-03
1
2
3
0.1
0.4
0.7
1
1.3
1.6
1.9
2.2
2.5
2.8
3.1
Vinn (V)
Figure 11. Typical hysteresis vs. Vin level (VDD = 3.3 V, PMODE = 1)
3.6.3 12-bit DAC electrical characteristics
32
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
3.6.3.1 12-bit DAC operating requirements
Table 28. 12-bit DAC operating requirements
Symbol
VDDA
VDACR
CL
Desciption
Min.
1.71
Max.
3.6
Unit
V
Notes
Supply voltage
Reference voltage
Output load capacitance
Output load current
1.13
—
3.6
100
1
V
1
2
pF
mA
IL
—
1. The DAC reference can be selected to be VDDA or VREFH
.
2. A small load capacitance (47 pF) can improve the bandwidth performance of the DAC.
3.6.3.2 12-bit DAC operating behaviors
Table 29. 12-bit DAC operating behaviors
Symbol Description
Min.
Typ.
Max.
Unit
Notes
IDDA_DACL Supply current — low-power mode
—
—
250
μA
μA
μs
μs
μs
P
IDDA_DACH Supply current — high-speed mode
—
—
—
—
—
100
15
900
200
30
P
tDACLP Full-scale settling time (0x080 to 0xF7F) —
low-power mode
1
1
1
tDACHP Full-scale settling time (0x080 to 0xF7F) —
high-power mode
tCCDACLP Code-to-code settling time (0xBF8 to
0xC08) — low-power mode and high-
speed mode
0.7
1
Vdacoutl DAC output voltage range low — high-
speed mode, no load, DAC set to 0x000
—
—
—
—
—
—
100
mV
mV
Vdacouth DAC output voltage range high — high-
speed mode, no load, DAC set to 0xFFF
VDACR
−100
VDACR
INL
DNL
DNL
Integral non-linearity error — high speed
mode
—
—
—
8
1
1
LSB
LSB
LSB
2
3
4
Differential non-linearity error — VDACR > 2
V
Differential non-linearity error — VDACR
VREF_OUT
=
VOFFSET Offset error
EG Gain error
PSRR Power supply rejection ratio, VDDA ≥ 2.4 V
—
—
60
—
—
—
0.4
0.1
0.8
0.6
90
%FSR
%FSR
dB
5
5
—
TCO
TGE
Rop
SR
Temperature coefficient offset voltage
Temperature coefficient gain error
Output resistance (load = 3 kΩ)
Slew rate -80h→ F7Fh→ 80h
3.7
—
μV/C
%FSR/C
Ω
6
0.000421
—
—
250
V/μs
1.2
1.7
—
Table continues on the next page...
Kinetis KL15 Sub-Family, Rev5 08/2014.
33
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 29. 12-bit DAC operating behaviors (continued)
Symbol Description
• High power (SPHP
• Low power (SPLP
Min.
Typ.
Max.
Unit
Notes
)
0.05
0.12
—
)
BW
3dB bandwidth
• High power (SPHP
• Low power (SPLP
kHz
)
550
40
—
—
—
—
)
1. Settling within 1 LSB
2. The INL is measured for 0 + 100 mV to VDACR −100 mV
3. The DNL is measured for 0 + 100 mV to VDACR −100 mV
4. The DNL is measured for 0 + 100 mV to VDACR −100 mV with VDDA > 2.4 V
5. Calculated by a best fit curve from VSS + 100 mV to VDACR − 100 mV
6. VDDA = 3.0 V, reference select set for VDDA (DACx_CO:DACRFS = 1), high power mode (DACx_C0:LPEN = 0), DAC set
to 0x800, temperature range is across the full range of the device
8
6
4
2
0
-2
-4
-6
-8
0
500
1000
1500
2000
2500
3000
3500
4000
Digital Code
Figure 12. Typical INL error vs. digital code
34
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
Peripheral operating requirements and behaviors
1.499
1.4985
1.498
1.4975
1.497
1.4965
1.496
55
85
25
105
125
-40
Temperature °C
Figure 13. Offset at half scale vs. temperature
3.7 Timers
See General switching specifications.
3.8 Communication interfaces
Kinetis KL15 Sub-Family, Rev5 08/2014.
35
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
3.8.1 SPI switching specifications
The Serial Peripheral Interface (SPI) provides a synchronous serial bus with master and
slave operations. Many of the transfer attributes are programmable. The following
tables provide timing characteristics for classic SPI timing modes. See the SPI chapter
of the chip's Reference Manual for information about the modified transfer formats used
for communicating with slower peripheral devices.
All timing is shown with respect to 20% VDD and 80% VDD thresholds, unless noted, as
well as input signal transitions of 3 ns and a 30 pF maximum load on all SPI pins.
Table 30. SPI master mode timing on slew rate disabled pads
Num.
Symbol Description
Min.
Max.
Unit
Hz
Note
1
2
fop
Frequency of operation
fperiph/2048
2 x tperiph
fperiph/2
1
2
tSPSCK
SPSCK period
2048 x
tperiph
ns
3
4
5
tLead
tLag
Enable lead time
Enable lag time
1/2
1/2
—
—
tSPSCK
tSPSCK
ns
—
—
—
tWSPSCK Clock (SPSCK) high or low time
tperiph – 30
1024 x
tperiph
6
7
tSU
tHI
Data setup time (inputs)
Data hold time (inputs)
Data valid (after SPSCK edge)
Data hold time (outputs)
Rise time input
16
0
—
ns
ns
ns
ns
ns
—
—
—
—
—
—
10
8
tv
—
0
9
tHO
tRI
—
10
—
tperiph – 25
tFI
Fall time input
11
tRO
tFO
Rise time output
—
25
ns
—
Fall time output
1. For SPI0, fperiph is the bus clock (fBUS). For SPI1 fperiph is the system clock (fSYS).
2. tperiph = 1/fperiph
Table 31. SPI master mode timing on slew rate enabled pads
Num.
Symbol Description
Min.
Max.
Unit
Hz
Note
1
2
fop
Frequency of operation
fperiph/2048
2 x tperiph
fperiph/2
1
2
tSPSCK
SPSCK period
2048 x
tperiph
ns
3
4
5
tLead
tLag
Enable lead time
Enable lag time
1/2
1/2
—
—
tSPSCK
tSPSCK
ns
—
—
—
tWSPSCK Clock (SPSCK) high or low time
tperiph – 30
1024 x
tperiph
6
tSU
Data setup time (inputs)
Table continues on the next page...
96
—
ns
—
36
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
Peripheral operating requirements and behaviors
Table 31. SPI master mode timing on slew rate enabled pads (continued)
Num.
Symbol Description
Min.
0
Max.
Unit
ns
Note
—
7
8
tHI
tv
Data hold time (inputs)
—
52
Data valid (after SPSCK edge)
Data hold time (outputs)
Rise time input
—
0
ns
—
9
tHO
tRI
—
ns
—
10
—
tperiph – 25
ns
—
tFI
Fall time input
11
tRO
tFO
Rise time output
—
36
ns
—
Fall time output
1. For SPI0, fperiph is the bus clock (fBUS). For SPI1 fperiph is the system clock (fSYS).
2. tperiph = 1/fperiph
1
SS
(OUTPUT)
3
2
10
10
11
11
4
SPSCK
(CPOL=0)
(OUTPUT)
5
5
SPSCK
(CPOL=1)
(OUTPUT)
6
7
MISO
(INPUT)
2
BIT 6 . . . 1
8
MSB IN
LSB IN
9
MOSI
(OUTPUT)
2
BIT 6 . . . 1
MSB OUT
LSB OUT
1. If configured as an output.
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure 14. SPI master mode timing (CPHA = 0)
Kinetis KL15 Sub-Family, Rev5 08/2014.
37
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
1
SS
(OUTPUT)
2
10
10
11
11
4
3
SPSCK
(CPOL=0)
(OUTPUT)
5
5
SPSCK
(CPOL=1)
(OUTPUT)
6
7
MISO
(INPUT)
2
BIT 6 . . . 1
LSB IN
MSB IN
9
8
MOSI
(OUTPUT)
2
PORT DATA
BIT 6 . . . 1
MASTER MSB OUT
PORT DATA
MASTER LSB OUT
1.If configured as output
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure 15. SPI master mode timing (CPHA = 1)
Table 32. SPI slave mode timing on slew rate disabled pads
Num.
1
Symbol Description
Min.
Max.
fperiph/4
—
Unit
Hz
Note
1
fop
tSPSCK
tLead
tLag
Frequency of operation
0
2
SPSCK period
Enable lead time
Enable lag time
4 x tperiph
ns
2
3
1
—
tperiph
tperiph
ns
—
—
—
—
—
3
4
1
—
5
tWSPSCK Clock (SPSCK) high or low time
tperiph – 30
—
6
tSU
tHI
ta
Data setup time (inputs)
Data hold time (inputs)
Slave access time
2
7
—
ns
7
—
ns
8
—
—
—
0
tperiph
tperiph
22
ns
9
tdis
tv
Slave MISO disable time
Data valid (after SPSCK edge)
Data hold time (outputs)
Rise time input
ns
4
10
11
12
ns
—
—
—
tHO
tRI
tFI
—
ns
—
tperiph – 25
ns
Fall time input
13
tRO
tFO
Rise time output
—
25
ns
—
Fall time output
1. For SPI0, fperiph is the bus clock (fBUS). For SPI1 fperiph is the system clock (fSYS).
2. tperiph = 1/fperiph
3. Time to data active from high-impedance state
4. Hold time to high-impedance state
38
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 33. SPI slave mode timing on slew rate enabled pads
Num.
1
Symbol Description
Min.
Max.
fperiph/4
—
Unit
Hz
Note
1
fop
tSPSCK
tLead
tLag
Frequency of operation
0
2
SPSCK period
Enable lead time
Enable lag time
4 x tperiph
ns
2
3
1
—
tperiph
tperiph
ns
—
—
—
—
—
3
4
1
—
5
tWSPSCK Clock (SPSCK) high or low time
tperiph – 30
—
6
tSU
tHI
ta
Data setup time (inputs)
Data hold time (inputs)
Slave access time
2
7
—
ns
7
—
ns
8
—
—
—
0
tperiph
tperiph
122
ns
9
tdis
tv
Slave MISO disable time
Data valid (after SPSCK edge)
Data hold time (outputs)
Rise time input
ns
4
10
11
12
ns
—
—
—
tHO
tRI
tFI
—
ns
—
tperiph – 25
ns
Fall time input
13
tRO
tFO
Rise time output
—
36
ns
—
Fall time output
1. For SPI0, fperiph is the bus clock (fBUS). For SPI1 fperiph is the system clock (fSYS).
2. tperiph = 1/fperiph
3. Time to data active from high-impedance state
4. Hold time to high-impedance state
SS
(INPUT)
2
12
12
13
13
4
SPSCK
(CPOL=0)
(INPUT)
5
5
3
SPSCK
(CPOL=1)
(INPUT)
9
8
10
11
11
see
note
SEE
NOTE
MISO
(OUTPUT)
BIT 6 . . . 1
SLAVE MSB
7
SLAVE LSB OUT
6
MOSI
(INPUT)
LSB IN
MSB IN
BIT 6 . . . 1
NOTE: Not defined
Figure 16. SPI slave mode timing (CPHA = 0)
Kinetis KL15 Sub-Family, Rev5 08/2014.
39
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
SS
(INPUT)
4
2
12
12
13
13
3
SPSCK
(CPOL=0)
(INPUT)
5
5
SPSCK
(CPOL=1)
(INPUT)
11
9
10
SLAVE MSB OUT
see
note
MISO
(OUTPUT)
BIT 6 . . . 1
BIT 6 . . . 1
SLAVE LSB OUT
LSB IN
8
6
7
MOSI
(INPUT)
MSB IN
NOTE: Not defined
Figure 17. SPI slave mode timing (CPHA = 1)
3.8.2 Inter-Integrated Circuit Interface (I2C) timing
Table 34. I2C timing
Characteristic
Symbol
Standard Mode
Minimum Maximum
100
Fast Mode
Unit
Minimum
Maximum
4001
SCL Clock Frequency
fSCL
0
0
kHz
µs
Hold time (repeated) START condition.
After this period, the first clock pulse is
generated.
tHD; STA
4
—
0.6
—
LOW period of the SCL clock
HIGH period of the SCL clock
tLOW
tHIGH
4.7
4
—
—
—
1.3
0.6
0.6
—
—
—
µs
µs
µs
Set-up time for a repeated START
condition
tSU; STA
4.7
Data hold time for I2C bus devices
tHD; DAT
tSU; DAT
tr
02
2505
—
3.453
—
04
1003, 6
20 +0.1Cb
20 +0.1Cb
0.6
0.92
—
µs
ns
ns
ns
µs
µs
Data set-up time
7
6
Rise time of SDA and SCL signals
Fall time of SDA and SCL signals
Set-up time for STOP condition
1000
300
—
300
300
—
tf
—
tSU; STO
tBUF
4
Bus free time between STOP and
START condition
4.7
—
1.3
—
Pulse width of spikes that must be
suppressed by the input filter
tSP
N/A
N/A
0
50
ns
1. The maximum SCL Clock Frequency in Fast mode with maximum bus loading can only achieved when using the High
drive pins (see Voltage and current operating behaviors) or when using the Normal drive pins and VDD ≥ 2.7 V
40
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
2. The master mode I2C deasserts ACK of an address byte simultaneously with the falling edge of SCL. If no slaves
acknowledge this address byte, then a negative hold time can result, depending on the edge rates of the SDA and
SCL lines.
3. The maximum tHD; DAT must be met only if the device does not stretch the LOW period (tLOW) of the SCL signal.
4. Input signal Slew = 10 ns and Output Load = 50 pF
5. Set-up time in slave-transmitter mode is 1 IPBus clock period, if the TX FIFO is empty.
6. A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but the requirement tSU; DAT ≥ 250 ns
must then be met. This is automatically the case if the device does not stretch the LOW period of the SCL signal. If
such a device does stretch the LOW period of the SCL signal, then it must output the next data bit to the SDA line trmax
+ tSU; DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification) before the SCL line is
released.
7. Cb = total capacitance of the one bus line in pF.
SDA
tSU; DAT
tf
tr
tBUF
tf
tr
tHD; STA
tSP
tLOW
SCL
tSU; STA
tSU; STO
HD; STA
S
SR
P
S
tHD; DAT
tHIGH
Figure 18. Timing definition for fast and standard mode devices on the I2C bus
3.8.3 UART
See General switching specifications.
3.9 Human-machine interfaces (HMI)
3.9.1 TSI electrical specifications
Table 35. TSI electrical specifications
Symbol
TSI_RUNF
TSI_RUNV
Description
Min.
—
Typ.
100
—
Max.
—
Unit
µA
Fixed power consumption in run mode
Variable power consumption in run mode
(depends on oscillator's current selection)
1.0
128
µA
TSI_EN
TSI_DIS
Power consumption in enable mode
Power consumption in disable mode
TSI analog enable time
—
—
100
1.2
66
—
—
µA
µA
µs
pF
V
TSI_TEN
—
—
TSI_CREF
TSI_DVOLT
TSI reference capacitor
—
1.0
—
—
Voltage variation of VP & VM around nominal
values
0.19
1.03
Kinetis KL15 Sub-Family, Rev5 08/2014.
41
Freescale Semiconductor, Inc.
Dimensions
4 Dimensions
4.1 Obtaining package dimensions
Package dimensions are provided in package drawings.
To find a package drawing, go to freescale.com and perform a keyword search for the
drawing’s document number:
If you want the drawing for this package
32-pin QFN
Then use this document number
98ASA00473D
48-pin QFN
64-pin LQFP
80-pin LQFP
98ASA00466D
98ASS23234W
98ASS23174W
5 Pinout
5.1 KL15 Signal Multiplexing and Pin Assignments
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The Port Control Module is responsible
for selecting which ALT functionality is available on each pin.
80
64
48
32
QFN
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
I2C1_SDA
I2C1_SCL
ALT7
LQFP LQFP QFN
1
1
—
1
PTE0
DISABLED
PTE0
UART1_TX
UART1_RX
RTC_
CLKOUT
CMP0_OUT
SPI1_MISO
2
3
4
5
6
7
8
9
2
—
—
—
—
3
—
—
—
—
—
1
2
PTE1
PTE2
PTE3
PTE4
PTE5
VDD
DISABLED
DISABLED
DISABLED
DISABLED
DISABLED
VDD
PTE1
PTE2
PTE3
PTE4
PTE5
SPI1_MOSI
SPI1_SCK
SPI1_MISO
SPI1_PCS0
—
—
—
—
—
—
3
SPI1_MOSI
VDD
4
2
VSS
VSS
VSS
5
3
PTE16
ADC0_DP1/
ADC0_SE1
ADC0_DP1/
ADC0_SE1
PTE16
SPI0_PCS0
UART2_TX
TPM_
CLKIN0
42
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
Pinout
80
64
48
32
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
LQFP LQFP QFN
QFN
10
11
12
13
14
15
16
6
7
4
5
4
5
PTE17
ADC0_DM1/
ADC0_SE5a
ADC0_DM1/
ADC0_SE5a
PTE17
SPI0_SCK
SPI0_MOSI
SPI0_MISO
UART2_RX
TPM_
CLKIN1
LPTMR0_
ALT3
PTE18
PTE19
PTE20
PTE21
PTE22
PTE23
ADC0_DP2/
ADC0_SE2
ADC0_DP2/
ADC0_SE2
PTE18
PTE19
PTE20
PTE21
PTE22
PTE23
I2C0_SDA
SPI0_MISO
SPI0_MOSI
8
6
6
ADC0_DM2/
ADC0_SE6a
ADC0_DM2/
ADC0_SE6a
I2C0_SCL
UART0_TX
UART0_RX
UART2_TX
UART2_RX
9
7
—
—
—
—
ADC0_DP0/
ADC0_SE0
ADC0_DP0/
ADC0_SE0
TPM1_CH0
TPM1_CH1
TPM2_CH0
TPM2_CH1
10
11
12
8
ADC0_DM0/
ADC0_SE4a
ADC0_DM0/
ADC0_SE4a
—
—
ADC0_DP3/
ADC0_SE3
ADC0_DP3/
ADC0_SE3
ADC0_DM3/
ADC0_SE7a
ADC0_DM3/
ADC0_SE7a
17
18
19
20
21
13
14
15
16
17
9
7
VDDA
VREFH
VREFL
VSSA
VDDA
VREFH
VREFL
VSSA
VDDA
VREFH
VREFL
VSSA
10
11
12
13
—
—
8
—
PTE29
CMP0_IN5/
ADC0_SE4b
CMP0_IN5/
ADC0_SE4b
PTE29
PTE30
TPM0_CH2
TPM0_CH3
TPM_
CLKIN0
22
18
14
9
PTE30
DAC0_OUT/
DAC0_OUT/
TPM_
ADC0_SE23/ ADC0_SE23/
CLKIN1
CMP0_IN4
DISABLED
DISABLED
DISABLED
SWD_CLK
DISABLED
DISABLED
SWD_DIO
NMI_b
CMP0_IN4
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
19
20
21
22
23
24
25
26
27
28
29
—
—
—
—
30
31
32
—
15
16
17
18
19
20
21
—
—
—
—
—
—
—
22
23
24
—
—
—
10
11
12
13
14
—
—
—
—
—
—
—
15
16
17
PTE31
PTE24
PTE25
PTA0
PTE31
PTE24
PTE25
PTA0
TPM0_CH4
TPM0_CH0
TPM0_CH1
TPM0_CH5
TPM2_CH0
TPM2_CH1
TPM0_CH0
TPM0_CH1
TPM0_CH2
TPM1_CH0
TPM1_CH1
UART0_TX
UART0_RX
I2C0_SCL
I2C0_SDA
TSI0_CH1
TSI0_CH2
TSI0_CH3
TSI0_CH4
TSI0_CH5
SWD_CLK
PTA1
PTA1
UART0_RX
UART0_TX
I2C1_SCL
I2C1_SDA
PTA2
PTA2
PTA3
PTA3
SWD_DIO
NMI_b
PTA4
PTA4
PTA5
DISABLED
DISABLED
DISABLED
DISABLED
DISABLED
DISABLED
DISABLED
VDD
PTA5
PTA12
PTA13
PTA14
PTA15
PTA16
PTA17
VDD
PTA12
PTA13
PTA14
PTA15
PTA16
PTA17
SPI0_PCS0
SPI0_SCK
SPI0_MOSI
SPI0_MISO
SPI0_MISO
SPI0_MOSI
VDD
VSS
VSS
VSS
PTA18
EXTAL0
EXTAL0
PTA18
UART1_RX
TPM_
CLKIN0
Kinetis KL15 Sub-Family, Rev5 08/2014.
43
Freescale Semiconductor, Inc.
Pinout
80
64
48
32
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
LQFP LQFP QFN
QFN
41
33
25
18
PTA19
XTAL0
XTAL0
PTA19
UART1_TX
TPM_
CLKIN1
LPTMR0_
ALT1
42
43
34
35
26
27
19
20
PTA20
RESET_b
PTA20
RESET_b
PTB0/
LLWU_P5
ADC0_SE8/
TSI0_CH0
ADC0_SE8/
TSI0_CH0
PTB0/
LLWU_P5
I2C0_SCL
I2C0_SDA
I2C0_SCL
I2C0_SDA
TPM1_CH0
TPM1_CH1
TPM2_CH0
TPM2_CH1
EXTRG_IN
44
45
46
36
37
38
28
29
30
21
—
—
PTB1
PTB2
PTB3
ADC0_SE9/
TSI0_CH6
ADC0_SE9/
TSI0_CH6
PTB1
ADC0_SE12/ ADC0_SE12/ PTB2
TSI0_CH7 TSI0_CH7
ADC0_SE13/ ADC0_SE13/ PTB3
TSI0_CH8
DISABLED
DISABLED
DISABLED
DISABLED
TSI0_CH9
TSI0_CH8
47
48
49
50
51
—
—
—
—
39
—
—
—
—
31
—
—
—
—
—
PTB8
PTB8
PTB9
PTB9
PTB10
PTB11
PTB16
PTB10
PTB11
PTB16
SPI1_PCS0
SPI1_SCK
SPI1_MOSI
TSI0_CH9
UART0_RX
UART0_TX
TPM_
CLKIN0
SPI1_MISO
SPI1_MOSI
52
40
32
—
PTB17
TSI0_CH10
TSI0_CH10
PTB17
SPI1_MISO
TPM_
CLKIN1
53
54
55
41
42
43
—
—
33
—
—
—
PTB18
PTB19
PTC0
TSI0_CH11
TSI0_CH12
TSI0_CH11
TSI0_CH12
PTB18
PTB19
TPM2_CH0
TPM2_CH1
EXTRG_IN
ADC0_SE14/ ADC0_SE14/ PTC0
TSI0_CH13 TSI0_CH13
CMP0_OUT
56
44
34
22
PTC1/
LLWU_P6/
RTC_CLKIN
ADC0_SE15/ ADC0_SE15/ PTC1/
I2C1_SCL
I2C1_SDA
TPM0_CH0
TSI0_CH14
TSI0_CH14
LLWU_P6/
RTC_CLKIN
57
58
45
46
35
36
23
24
PTC2
ADC0_SE11/ ADC0_SE11/ PTC2
TPM0_CH1
TPM0_CH2
TSI0_CH15
TSI0_CH15
PTC3/
LLWU_P7
DISABLED
PTC3/
UART1_RX
UART1_TX
CLKOUT
LLWU_P7
59
60
61
47
48
49
—
—
37
—
—
25
VSS
VDD
VSS
VSS
VDD
VDD
PTC4/
LLWU_P8
DISABLED
PTC4/
SPI0_PCS0
SPI0_SCK
SPI0_MOSI
TPM0_CH3
LLWU_P8
62
63
50
51
38
39
26
27
PTC5/
LLWU_P9
DISABLED
CMP0_IN0
PTC5/
LLWU_P9
LPTMR0_
ALT2
CMP0_OUT
PTC6/
CMP0_IN0
PTC6/
EXTRG_IN
SPI0_MISO
SPI0_MOSI
LLWU_P10
LLWU_P10
64
65
66
67
68
52
53
54
55
56
40
—
—
—
—
28
—
—
—
—
PTC7
PTC8
PTC9
PTC10
PTC11
CMP0_IN1
CMP0_IN2
CMP0_IN3
DISABLED
DISABLED
CMP0_IN1
CMP0_IN2
CMP0_IN3
PTC7
PTC8
PTC9
PTC10
PTC11
SPI0_MISO
I2C0_SCL
I2C0_SDA
I2C1_SCL
I2C1_SDA
TPM0_CH4
TPM0_CH5
44
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
Pinout
80
64
48
32
QFN
Pin Name
PTC12
Default
DISABLED
DISABLED
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
LQFP LQFP QFN
69
70
—
—
—
—
—
—
PTC12
TPM_
CLKIN0
PTC13
PTC13
TPM_
CLKIN1
71
72
73
74
75
76
77
—
—
57
58
59
60
61
—
—
41
42
43
44
45
—
—
—
—
—
—
29
PTC16
PTC17
PTD0
PTD1
PTD2
PTD3
DISABLED
DISABLED
DISABLED
ADC0_SE5b
DISABLED
DISABLED
DISABLED
PTC16
PTC17
PTD0
PTD1
PTD2
PTD3
SPI0_PCS0
SPI0_SCK
SPI0_MOSI
SPI0_MISO
SPI1_PCS0
TPM0_CH0
TPM0_CH1
TPM0_CH2
TPM0_CH3
TPM0_CH4
ADC0_SE5b
UART2_RX
UART2_TX
UART2_RX
SPI0_MISO
SPI0_MOSI
PTD4/
PTD4/
LLWU_P14
LLWU_P14
78
79
62
63
46
47
30
31
PTD5
ADC0_SE6b
ADC0_SE7b
ADC0_SE6b
ADC0_SE7b
PTD5
SPI1_SCK
UART2_TX
UART0_RX
TPM0_CH5
PTD6/
LLWU_P15
PTD6/
LLWU_P15
SPI1_MOSI
SPI1_MISO
SPI1_MOSI
80
64
48
32
PTD7
DISABLED
PTD7
SPI1_MISO
UART0_TX
5.2 KL15 pinouts
The following figures show the pinout diagrams for the devices supported by this
document. Many signals may be multiplexed onto a single pin. To determine what
signals can be used on which pin, see KL15 Signal Multiplexing and Pin
Assignments.
Kinetis KL15 Sub-Family, Rev5 08/2014.
45
Freescale Semiconductor, Inc.
Pinout
1
PTE0
PTE1
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
VDD
2
VSS
3
PTE2
PTC3/LLWU_P7
PTC2
4
PTE3
5
PTE4
PTC1/LLWU_P6/RTC_CL
PTC0
6
PTE5
7
VDD
PTB19
8
VSS
PTB18
9
PTE16
PTE17
PTE18
PTE19
PTE20
PTE21
PTE22
PTE23
VDDA
VREFH
VREFL
VSSA
PTB17
10
11
12
13
14
15
16
17
18
19
20
PTB16
PTB11
PTB10
PTB9
PTB8
PTB3
PTB2
PTB1
PTB0/LLWU_P5
PTA20
PTA19
Figure 19. KL15 80-pin LQFP pinout diagram
46
Freescale Semiconductor, Inc.
Kinetis KL15 Sub-Family, Rev5 08/2014.
Pinout
PTE0
PTE1
1
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
VDD
2
VSS
VDD
3
PTC3/LLWU_P7
PTC2
VSS
4
PTE16
PTE17
PTE18
PTE19
PTE20
PTE21
PTE22
PTE23
VDDA
VREFH
VREFL
VSSA
5
PTC1/LLWU_P6/RTC_CLKIN
6
PTC0
7
PTB19
PTB18
PTB17
PTB16
PTB3
8
9
10
11
12
13
14
15
16
PTB2
PTB1
PTB0/LLWU_P5
PTA20
PTA19
Figure 20. KL15 64-pin LQFP pinout diagram
Kinetis KL15 Sub-Family, Rev5 08/2014.
47
Freescale Semiconductor, Inc.
Pinout
PTC3/LLWU_P7
36
35
34
33
32
31
30
29
28
27
26
25
VDD
VSS
1
2
PTC2
PTC1/LLWU_P6/RTC_CLKIN
PTE16
PTE17
PTE18
PTE19
PTE20
PTE21
VDDA
VREFH
VREFL
VSSA
3
PTC0
4
PTB17
PTB16
PTB3
5
6
7
PTB2
8
PTB1
9
PTB0/LLWU_P5
PTA20
PTA19
10
11
12
Figure 21. KL15 48-pin QFN pinout diagram
48
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Ordering parts
PTC3/LLWU_P7
PTC2
PTE0
PTE1
24
23
22
21
20
19
1
2
3
4
5
6
7
8
PTC1/LLWU_P6/RTC_CLKIN
PTE16
PTE17
PTE18
PTE19
VDDA
VSSA
PTB1
PTB0/LLWU_P5
PTA20
PTA19
18
17
PTA18
Figure 22. KL15 32-pin QFN pinout diagram
6 Ordering parts
6.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web. To determine the orderable
part numbers for this device, go to freescale.com and perform a part number search
for the following device numbers: PKL15 and MKL15
7 Part identification
Kinetis KL15 Sub-Family, Rev5 08/2014.
49
Freescale Semiconductor, Inc.
Part identification
7.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
7.2 Format
Part numbers for this device have the following format:
Q KL## A FFF R T PP CC N
7.3 Fields
This table lists the possible values for each field in the part number (not all
combinations are valid):
Table 36. Part number fields descriptions
Field
Description
Values
Q
Qualification status
• M = Fully qualified, general market flow
• P = Prequalification
KL##
A
Kinetis family
Key attribute
• KL15
• Z = Cortex-M0+
FFF
Program flash memory size
• 32 = 32 KB
• 64 = 64 KB
• 128 = 128 KB
R
Silicon revision
• (Blank) = Main
• A = Revision after main
T
Temperature range (°C)
Package identifier
• V = –40 to 105
PP
• FM = 32 QFN (5 mm x 5 mm)
• FT = 48 QFN (7 mm x 7 mm)
• LH = 64 LQFP (10 mm x 10 mm)
• LK = 80 LQFP (12 mm x 12 mm)
CC
N
Maximum CPU frequency (MHz)
Packaging type
• 4 = 48 MHz
• R = Tape and reel
• (Blank) = Trays
50
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Terminology and guidelines
7.4 Example
This is an example part number:
MKL15Z32VFT4
8 Terminology and guidelines
8.1 Definition: Operating requirement
An operating requirement is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation
and possibly decreasing the useful life of the chip.
8.1.1 Example
This is an example of an operating requirement:
Symbol
Description
Min.
Max.
Unit
VDD
1.0 V core supply
voltage
0.9
1.1
V
8.2 Definition: Operating behavior
Unless otherwise specified, an operating behavior is a specified value or range of
values for a technical characteristic that are guaranteed during operation if you meet
the operating requirements and any other specified conditions.
8.2.1 Example
This is an example of an operating behavior:
Symbol
Description
Min.
Max.
Unit
IWP
Digital I/O weak pullup/ 10
pulldown current
130
µA
Kinetis KL15 Sub-Family, Rev5 08/2014.
51
Freescale Semiconductor, Inc.
Terminology and guidelines
8.3 Definition: Attribute
An attribute is a specified value or range of values for a technical characteristic that are
guaranteed, regardless of whether you meet the operating requirements.
8.3.1 Example
This is an example of an attribute:
Symbol
Description
Min.
Max.
Unit
CIN_D
Input capacitance:
digital pins
—
7
pF
8.4 Definition: Rating
A rating is a minimum or maximum value of a technical characteristic that, if exceeded,
may cause permanent chip failure:
• Operating ratings apply during operation of the chip.
• Handling ratings apply when the chip is not powered.
8.4.1 Example
This is an example of an operating rating:
Symbol
Description
Min.
Max.
Unit
VDD
1.0 V core supply
voltage
–0.3
1.2
V
52
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Terminology and guidelines
8.5 Result of exceeding a rating
40
30
The likelihood of permanent chip failure increases rapidly as
soon as a characteristic begins to exceed one of its operating ratings.
20
10
0
Operating rating
Measured characteristic
8.6 Relationship between ratings and operating requirements
Fatal range
Degraded operating range
Normal operating range
Degraded operating range
Fatal range
Expected permanent failure
- No permanent failure
- No permanent failure
- Correct operation
- No permanent failure
Expected permanent failure
- Possible decreased life
- Possible incorrect operation
- Possible decreased life
- Possible incorrect operation
–∞
∞
Operating (power on)
Fatal range
Handling range
Fatal range
Expected permanent failure
No permanent failure
Expected permanent failure
–∞
∞
Handling (power off)
8.7 Guidelines for ratings and operating requirements
Follow these guidelines for ratings and operating requirements:
• Never exceed any of the chip’s ratings.
• During normal operation, don’t exceed any of the chip’s operating requirements.
• If you must exceed an operating requirement at times other than during normal
operation (for example, during power sequencing), limit the duration as much as
possible.
Kinetis KL15 Sub-Family, Rev5 08/2014.
53
Freescale Semiconductor, Inc.
Terminology and guidelines
8.8 Definition: Typical value
A typical value is a specified value for a technical characteristic that:
• Lies within the range of values specified by the operating behavior
• Given the typical manufacturing process, is representative of that characteristic
during operation when you meet the typical-value conditions or other specified
conditions
Typical values are provided as design guidelines and are neither tested nor guaranteed.
8.8.1 Example 1
This is an example of an operating behavior that includes a typical value:
Symbol
Description
Min.
Typ.
Max.
Unit
IWP
Digital I/O weak
pullup/pulldown
current
10
70
130
µA
8.8.2 Example 2
This is an example of a chart that shows typical values for various voltage and
temperature conditions:
54
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Revision history
5000
4500
4000
3500
3000
2500
2000
1500
1000
500
TJ
150 °C
105 °C
25 °C
–40 °C
0
0.90
0.95
1.00
1.05
1.10
VDD (V)
8.9 Typical value conditions
Typical values assume you meet the following conditions (or other conditions as
specified):
Table 37. Typical value conditions
Symbol
TA
Description
Value
25
Unit
°C
Ambient temperature
3.3 V supply voltage
VDD
3.3
V
9 Revision history
The following table provides a revision history for this document.
Table 38. Revision history
Rev. No.
Date
9/2012
9/2012
Substantial Changes
2
3
Completed all the TBDs, initial public release.
Updated Signal Multiplexing and Pin Assignments table to add UART2
signals.
4
3/2014
• Updated the front page and restructured the chapters
Table continues on the next page...
Kinetis KL15 Sub-Family, Rev5 08/2014.
55
Freescale Semiconductor, Inc.
Revision history
Rev. No.
Table 38. Revision history (continued)
Date
Substantial Changes
• Added a note to the ILAT in the ESD handling ratings
• Updated Voltage and current operating ratings
• Updated Voltage and current operating requirements
• Updated the Voltage and current operating behaviors
• Updated Power mode transition operating behaviors
• Updated Capacitance attributes
• Updated footnote in the Device clock specifications
• Updated tersall in the Flash timing specifications — commands
• Updated VADIN in the 16-bit ADC operating conditions
• Updated Temp sensor slope and voltage and added a note to
them in the 16-bit ADC electrical characteristics
• Removed TA in the 12-bit DAC operating requirements
• Added Inter-Integrated Circuit Interface (I2C) timing
5
08/2014
• Updated related source and added block diagram in the front
page
• Updated Power consumption operating behaviors
56
Kinetis KL15 Sub-Family, Rev5 08/2014.
Freescale Semiconductor, Inc.
Information in this document is provided solely to enable system and
software implementers to use Freescale products. There are no express
or implied copyright licenses granted hereunder to design or fabricate
any integrated circuits based on the information in this document.
Freescale reserves the right to make changes without further notice to
any products herein.
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
Freescale makes no warranty, representation, or guarantee regarding
the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages.
“Typical” parameters that may be provided in Freescale data sheets
and/or specifications can and do vary in different applications, and
actual performance may vary over time. All operating parameters,
including “typicals,” must be validated for each customer application by
customer's technical experts. Freescale does not convey any license
under its patent rights nor the rights of others. Freescale sells products
pursuant to standard terms and conditions of sale, which can be found
at the following address: freescale.com/SalesTermsandConditions.
Freescale, Freescale logo, Energy Efficient Solutions logo, and Kinetis
are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm.
Off. All other product or service names are the property of their
respective owners. ARM and Cortex are registered trademarks of ARM
Limited (or its subsidiaries) in the EU and/or elsewhere. All rights
reserved.
© 2012-2014 Freescale Semiconductor, Inc.
Document Number KL15P80M48SF0
Revision 5 08/2014
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明