MMPF0100NPEP [NXP]
Power Management IC, i.MX6, no-prog ,4/6 buck, 6 LDO, 1 boost, QFN 56, Tray;
| 型号： | MMPF0100NPEP |
| 厂家： | 
NXP |
| 描述： | Power Management IC, i.MX6, no-prog ,4/6 buck, 6 LDO, 1 boost, QFN 56, Tray |
| 文件： | 总149页 (文件大小：1358K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Document order number: MMPF0100
Rev. 8.0, 6/2014
Freescale Semiconductor
Advance Information
14 Channel Configurable Power
Management Integrated Circuit
PF0100
The PF0100 SMARTMOS Power Management Integrated Circuit
(PMIC) provides a highly programmable/ configurable architecture,
with fully integrated power devices and minimal external components.
With up to six buck converters, six linear regulators, RTC supply, and
coin-cell charger, the PF0100 can provide power for a complete
system, including applications processors, memory, and system
peripherals, in a wide range of applications. With on-chip One Time
Programmable (OTP) memory, the PF0100 is available in pre-
programmed standard versions, or non-programmed to support
custom programming. The PF0100 is defined to power an entire
embedded MCU platform solution such as i.MX6 based eReader,
IPTV, medical monitoring, and home/factory automation.
POWER MANAGEMENT
EP SUFFIX (E-TYPE)
ES SUFFIX (WF-TYPE)
98ASA00589D
98ASA00405D
56 QFN 8X8
56 QFN 8X8
Applications:
Features:
• Tablets
• Four to six buck converters, depending on configuration
• IPTV
• eReaders
•
•
Single/Dual phase/ parallel options
DDR termination tracking mode option
• Set Top Boxes
• Industrial control
• Medical monitoring
• Boost regulator to 5.0 V output
• Six general purpose linear regulators
• Programmable output voltage, sequence, and timing
• OTP (One Time Programmable) memory for device configuration
• Coin cell charger and RTC supply
• Home automation/ alarm/ energy management
• DDR termination reference voltage
• Power control logic with processor interface and event detection
• I2C control
• Individually programmable ON, OFF, and Standby modes
PF0100
i.MX6X
VREFDDR
DDR MEMORY
INTERFACE
DDR Memory
SW4
1000 mA
SW3A/B
2500 mA
SW1A/B
2500 mA
Processor Core
Voltages
SW1C
2000 mA
External AMP
Microphones
Speakers
SW2
2000 mA
SATA - FLASH
SD-MMC/
NAND Mem.
SATA
HDD
NAND
- NOR
SWBST
600 mA
Interfaces
Audio
Codec
Parallel control/GPIOS
I2C Communication
Control Signals
I2C Communication
Sensors
VGEN1
100 mA
Camera
Camera
VGEN2
250 mA
GPS
MIPI
uPCIe
WAM
GPS
MIPI
VGEN3
100 mA
VGEN4
350 mA
HDMI
LDVS Display
VGEN5
100 mA
USB
Ethernet
CAN
LICELL
Charger
VGEN6
200 mA
Main Supply
2.8 – 4.5 V
COINCELL
Front USB
POD
Rear Seat
Infotaiment
Rear USB
POD
Cluster/HUD
Figure 1. Simplified Application Diagram
* This document contains certain information on a new product.
Specifications and information herein are subject to change without notice.
© Freescale Semiconductor, Inc., 2012-2014. All rights reserved.
Table of Contents
1
2
3
Orderable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Internal Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Pinout Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2.1 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.1 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.2 Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.2 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.3.1 Power Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.3.2 Control Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Functional Block Requirements and Behaviors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1.1 Device Start-up Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1.2 One Time Programmability (OTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1.3 OTP Prototyping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.1.4 Reading OTP Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.1.5 Programming OTP Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.2 16 MHz and 32 kHz Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.2.1 Clock adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.3 Bias and References Block Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.3.1 Internal Core Voltage References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.3.2 VREFDDR Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.4 Power Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.4.1 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.4.2 State Machine Flow Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.4.3 Power Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.4.4 Buck Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.4.5 Boost Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.4.6 LDO Regulators Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
6.4.7 VSNVS LDO/Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
6.5 Control Interface I2C Block Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
6.5.1 I2C Device ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
6.5.2 I2C Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
6.5.3 Interrupt Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
6.5.4 Interrupt Bit Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
6.5.5 Specific Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
6.5.6 Register Bitmap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
7.1.1 Application Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
7.1.2 Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
4
5
6
7
PF0100
Analog Integrated Circuit Device Data
2
Freescale Semiconductor
7.2 PF0100 Layout Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
7.2.1 General Board Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
7.2.2 Component Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
7.2.3 General Routing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
7.2.4 Parallel Routing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
7.2.5 Switching Regulator Layout Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
7.3 Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
7.3.1 Rating Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
7.3.2 Estimation of Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
8.1 Packaging Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Reference Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
9.1 Reference Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
8
9
10 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
Orderable Parts
1
Orderable Parts
The PF0100 is available with both pre-programmed and non-programmed OTP memory configurations. The non-programmed
device uses “NP” as the programming code. The pre-programmed devices are identified using the program codes from Table 1,
which also list the associated Freescale reference designs where applicable. Details of the OTP programming for each device
can be found in Table 10.
Table 1. Orderable Part Variations
Qualification
Temperature (T )
Part Number
Package
Programming Reference Designs
Notes
A
Tier
(2)(1)
MMPF0100NPEP
NP
F0
N/A
MCIMX6Q-SDP
MCIMX6Q-SDB
MCIMX6DL-SDP
(2)(1)
MMPF0100F0EP
56 QFN 8x8 mm - 0.5 mm pitch
E-Type QFN (full lead)
Consumer and
Industrial
(2)(1)(3)
(2)(1)(3)
(2)(1)
-40 to 85 °C
MMPF0100F1EP
MMPF0100F2EP
MMPF0100F3EP
MMPF0100F4EP
MMPF0100NPAEP
F1
F2
F3
F4
NP
MCIMX6SLEVK
N/A
N/A
N/A
N/A
(2)(1)
(2)(1)
MCIMX6Q-SDP
MCIMX6Q-SDB
MCIMX6DL-SDP
(2)(1)
MMPF0100F0AEP
F0
56 QFN 8x8 mm - 0.5 mm pitch
E-Type QFN (full lead)
(2)(1)(3)
(2)(1)(3)
(2)(1)
-40 to 85 °C
Consumer
MMPF0100F1AEP
MMPF0100F2AEP
MMPF0100F3AEP
MMPF0100F4AEP
MMPF0100NPANES
F1
F2
F3
F4
NP
MCIMX6SLEVK
N/A
N/A
N/A
N/A
(2)(1)
(2)(1)
MCIMX6Q-SDP
MCIMX6Q-SDB
MCIMX6DL-SDP
(2)(1)
MMPF0100F0ANES
F0
56 QFN 8x8 mm - 0.5 mm pitch
WF-Type QFN (wettable flank)
Extended
Industrial
-40 to 105 °C
(2)(1)
(2)(1)
MMPF0100F3ANES
MMPF0100F4ANES
Notes
F3
F4
N/A
N/A
1. For Tape and Reel add an R2 suffix to the part number.
2. For programming details see Table 10. The available OTP options are not restricted to the listed reference designs. They can be used
in any application where the listed voltage and sequence details are acceptable.
3. For designs using the i.MX6 Solo Lite, it is recommended to use the F3 OTP option instead of the F1 OTP option and F4 OTP option
instead of the F2 OTP option
PF0100
Analog Integrated Circuit Device Data
4
Freescale Semiconductor
Orderable Parts
PF0100 Version Differences
1.1
PF0100 Version Differences
PF0100A is an improved version of the PF0100 Power Management IC. Table 2 summarizes the difference between the two
versions and should be referred to when migrating from the PF0100 to the PF0100A. Note that programming options are the
same for both versions of the device.
Table 2. Differences between PF0100 and PF0100A
Description
PF0100
PF0100A
Reading SILICON REV register at address
0x03 will return 0x11. DEVICEID register at
address 0x00 will read 0x10 in PF0100 and
PF0100A
Reading SILICON REV register at address
0x03 will return 0x21. DEVICEID register at
address 0x00 will read 0x10 in PF0100 and
PF0100A
Version identification
VSNVS current limit
VSNVS current limit increased in the PF0100A
In the PF0100, FUSE_POR1, FUSE_POR2, In the PF0100A, the XOR function is removed.
and FUSE_POR3 bits are XOR’ed into the It is required to set FUSE_POR1,
FUSE_POR_XOR bit. The FUSE_POR_XOR FUSE_POR2, and FUSE_POR3 bits during
OTP_FUSE_PORx register setting during OTP
programming
bit has to be 1 for fuses to be loaded during
startup. This can be achieved by setting any
one or all of the FUSE_PORx bits during OTP
programming.
OTP programming.
Erratum ER19 applicable to PF0100.
Applications expecting to operate in the
conditions mentioned in ER19 need to
implement an external workaround to
overcome the problem. Refer to the product
errata for details
Errata ER19 fixed in PF0100A. External
workaround not required
Erratum ER19
Erratum ER20
Erratum ER22
Erratum ER20 applicable to PF0100
Erratum ER22 applicable to PF0100
Errata ER20 fixed in PF0100A
Errata ER22 fixed in PF0100A. Workaround
not required
In addition to the version differences, Table 3 shows the differences on the test temperature rating for each version of PF0100
covered on this datasheet.
Table 3. Ambient Temperature Range
Ambient Temperature range
Device
Qualification Tier
(TMIN to TMAX
)
MMPF0100
Consumer and Industrial
TA = -40 to 85 °C
TA = -40 to 85 °C
TA = -40 to 105 °C
MMPF0100A
Consumer
MMPF0100AN
Extended Industrial
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
Internal Block Diagram
PF0100 Version Differences
2
Internal Block Diagram
SW1FB
VGEN1
100 mA
VIN1
PF0100
SW1AIN
SW1ALX
VGEN1
O/P
Drive
SW1A/B
Single/Dual
2500 mA
Buck
VGEN2
250 mA
VGEN2
SW1BLX
SW1BIN
O/P
Drive
VIN2
VGEN3
100 mA
VGEN3
SW1CLX
SW1CIN
O/P
Drive
SW1C
2000 mA
Buck
VGEN4
350 mA
VGEN4
SW1CFB
Core Control logic
SW1VSSSNS
VIN3
VGEN5
100 mA
VGEN5
SW2LX
SW2IN
SW2IN
SW2FB
Initialization State Machine
SW2
2000 mA
Buck
O/P
Drive
VGEN6
200 mA
VGEN6
Supplies
Control
OTP
SW3AFB
SW3AIN
SW3ALX
O/P
Drive
VDDOTP
VDDIO
SW3A/B
Single/Dual
DDR
2500 mA
Buck
CONTROL
I2C
Interface
SW3BLX
SW3BIN
O/P
Drive
SCL
SDA
DVS CONTROL
SW3BFB
DVS Control
SW3VSSSNS
SW4FB
SW4
1000 mA
Buck
SW4IN
O/P
Drive
I2C Register
map
SW4LX
Trim-In-Package
VCOREDIG
VCOREREF
GNDREF1
Reference
Generation
SWBSTLX
Clocks and
resets
SWBST
600 mA
Boost
O/P
Drive
VCORE
SWBSTIN
SWBSTFB
GNDREF
VREFDDR
VINREFDDR
Clocks
32 kHz and 16 MHz
VHALF
VIN
Best
of
Supply
Li Cell
Charger
LICELL
VSNVS
Figure 2. Simplified Internal Block Diagram
PF0100
Analog Integrated Circuit Device Data
6
Freescale Semiconductor
Pin Connections
Pinout Diagram
3
Pin Connections
3.1
Pinout Diagram
56 55 54 53 52 51 50 49 48 47 46 45 44 43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
INTB
1
2
3
4
5
6
7
8
9
LICELL
SDWNB
VGEN6
RESETBMCU
STANDBY
ICTEST
VIN3
VGEN5
SW3AFB
SW3AIN
SW3ALX
SW3BLX
SW3BIN
SW3BFB
SW3VSSSNS
VREFDDR
VINREFDDR
VHALF
SW1FB
SW1AIN
EP
SW1ALX
SW1BLX
SW1BIN 10
SW1CLX 11
SW1CIN 12
SW1CFB 13
SW1VSSSNS 14
15 16 17 18 19 20 21 22 23 24 25 26 27 28
Figure 3. Pinout Diagram
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
Pin Connections
Pin Definitions
3.2
Pin Definitions
Table 4. PF0100 Pin Definitions
Pin
Function
Pin Number
Pin Name
Max Rating
Type
Definition
1
2
INTB
O
O
3.6 V
3.6 V
Digital
Digital
Open drain interrupt signal to processor
SDWNB
Open drain signal to indicate an imminent system shutdown
Open drain reset output to processor. Alternatively can be used
as a Power Good output.
3
4
5
RESETBMCU
STANDBY
ICTEST
O
I
3.6 V
3.6 V
7.5 V
Digital
Digital
Standby input signal from processor
Digital/
Analog
I
Reserved pin. Connect to GND in application.
Output voltage feedback for SW1A/B. Route this trace separately
from the high current path and terminate at the output
capacitance.
6
7
SW1FB (5)
SW1AIN (5)
I
I
3.6 V
4.8 V
Analog
Analog
Input to SW1A regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
8
9
SW1ALX (5)
SW1BLX (5)
O
O
4.8 V
4.8 V
Analog
Analog
Regulator 1A switch node connection
Regulator 1B switch node connection
Input to SW1B regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
10
11
12
SW1BIN (5)
SW1CLX (5)
SW1CIN (5)
I
O
I
4.8 V
4.8 V
4.8 V
Analog
Analog
Analog
Regulator 1C switch node connection
Input to SW1C regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
Output voltage feedback for SW1C. Route this trace separately
from the high current path and terminate at the output
capacitance.
13
SW1CFB (5)
I
3.6V
Analog
Ground reference for regulators SW1ABC. It is connected
externally to GNDREF through a board ground plane.
14
15
16
17
18
SW1VSSSNS
GNDREF1
VGEN1
GND
GND
O
-
GND
GND
Ground reference for regulators SW2 and SW4. It is connected
externally to GNDREF, via board ground plane.
-
VGEN1 regulator output, Bypass with a 2.2 F ceramic output
capacitor.
2.5 V
3.6 V
2.5 V
Analog
Analog
Analog
VGEN1, 2 input supply. Bypass with a 1.0 F decoupling
capacitor as close to the pin as possible.
VIN1
I
VGEN2 regulator output, Bypass with a 4.7 F ceramic output
capacitor.
VGEN2
O
Output voltage feedback for SW4. Route this trace separately
from the high current path and terminate at the output
capacitance.
19
20
SW4FB (5)
SW4IN (5)
I
I
3.6 V
4.8 V
Analog
Analog
Input to SW4 regulator. Bypass with at least a 4.7F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
21
22
SW4LX (5)
SW2LX (5)
O
O
4.8 V
4.8 V
Analog
Analog
Regulator 4 switch node connection
Regulator 2 switch node connection
PF0100
Analog Integrated Circuit Device Data
8
Freescale Semiconductor
Pin Connections
Pin Definitions
Table 4. PF0100 Pin Definitions (continued)
Pin
Pin Number
Pin Name
Max Rating
Type
Definition
Function
23
24
SW2IN (5)
SW2IN (5)
I
I
4.8 V
4.8 V
Analog
Analog
Input to SW2 regulator. Connect pin 23 together with pin 24 and
bypass with at least a 4.7 F ceramic capacitor and a 0.1 F
decoupling capacitor as close to these pins as possible.
Output voltage feedback for SW2. Route this trace separately
from the high current path and terminate at the output
capacitance.
25
SW2FB (5)
I
3.6 V
Analog
VGEN3 regulator output. Bypass with a 2.2 F ceramic output
capacitor.
26
27
VGEN3
VIN2
O
I
3.6 V
3.6 V
Analog
Analog
VGEN3,4 input. Bypass with a 1.0 F decoupling capacitor as
close to the pin as possible.
VGEN4 regulator output, Bypass with a 4.7 F ceramic output
capacitor.
28
29
30
31
32
VGEN4
VHALF
O
3.6 V
3.6 V
3.6 V
3.6 V
-
Analog
Analog
Analog
Analog
GND
I
I
Half supply reference for VREFDDR
VREFDDR regulator input. Bypass with at least 1.0 F decoupling
capacitor as close to the pin as possible.
VINREFDDR
VREFDDR
SW3VSSSNS
O
VREFDDR regulator output
Ground reference for the SW3 regulator. Connect to GNDREF
externally via the board ground plane.
GND
Output voltage feedback for SW3B. Route this trace separately
from the high current path and terminate at the output
capacitance.
33
34
SW3BFB (5)
SW3BIN (5)
I
I
3.6 V
4.8 V
Analog
Analog
Input to SW3B regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
35
36
SW3BLX (5)
SW3ALX (5)
O
O
4.8 V
4.8 V
Analog
Analog
Regulator 3B switch node connection
Regulator 3A switch node connection
Input to SW3A regulator. Bypass with at least a 4.7 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
37
38
SW3AIN (5)
SW3AFB (5)
I
I
4.8 V
3.6 V
Analog
Analog
Output voltage feedback for SW3A. Route this trace separately
from the high current path and terminate at the output
capacitance.
VGEN5 regulator output. Bypass with a 2.2 F ceramic output
capacitor.
39
40
41
VGEN5
VIN3
O
I
3.6 V
4.8 V
3.6 V
Analog
Analog
Analog
VGEN5, 6 input. Bypass with a 1.0 F decoupling capacitor as
close to the pin as possible.
VGEN6 regulator output. By pass with a 2.2 F ceramic output
capacitor.
VGEN6
O
42
43
LICELL
VSNVS
I/O
O
3.6 V
3.6 V
Analog
Analog
Coin cell supply input/output
LDO or coin cell output to processor
Boost regulator feedback. Connect this pin to the output rail close
to the load. Keep this trace away from other noisy traces and
planes.
44
45
SWBSTFB (5)
SWBSTIN (5)
I
I
5.5 V
4.8 V
Analog
Analog
Input to SWBST regulator. Bypass with at least a 2.2 F ceramic
capacitor and a 0.1 F decoupling capacitor as close to the pin as
possible.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
Pin Connections
Pin Definitions
Table 4. PF0100 Pin Definitions (continued)
Pin
Pin Number
Pin Name
Max Rating
Type
Definition
SWBST switch node connection
Function
46
47
SWBSTLX (5)
VDDOTP
O
7.5 V
Analog
Digital &
Analog
I
10 V(4)
Supply to program OTP fuses
48
49
50
51
52
53
54
55
56
GNDREF
VCORE
VIN
GND
-
GND
Ground reference for the main band gap regulator.
Analog Core supply
O
I
3.6 V
4.8 V
1.5 V
1.5 V
3.6 V
3.6 V
3.6 V
3.6 V
Analog
Analog
Analog
Analog
Digital
Digital
Analog
Digital
Main chip supply
VCOREDIG
VCOREREF
SDA
O
O
I/O
I
Digital Core supply
Main band gap reference
I2C data line (Open drain)
I2C clock
SCL
VDDIO
I
Supply for I2C bus. Bypass with 0.1 F ceramic capacitor
Power On/off from processor
PWRON
I
Expose pad. Functions as ground return for buck regulators. Tie
this pad to the inner and external ground planes through vias to
allow effective thermal dissipation.
-
EP
GND
-
GND
Notes
4. 10 V Maximum voltage rating during OTP fuse programming. 7.5 V Maximum DC voltage rated otherwise.
5. Unused switching regulators should be connected as follow: Pins SWxLX and SWxFB should be unconnected and Pin SWxIN should
be connected to VIN with a 0.1 F bypass capacitor.
PF0100
Analog Integrated Circuit Device Data
10
Freescale Semiconductor
General Product Characteristics
Absolute Maximum Ratings
4
General Product Characteristics
4.1
Absolute Maximum Ratings
Table 5. Absolute Maximum Ratings
All voltages are with respect to ground, unless otherwise noted. Exceeding these ratings may cause malfunction or permanent
damage to the device. The detailed maximum voltage rating per pin can be found in the pin list section.
Symbol
Description
Value
Unit
ELECTRICAL RATINGS
V
Main input supply voltage
-0.3 to 4.8
-0.3 to 10
-0.3 to 3.6
V
V
V
IN
V
OTP programming input supply voltage
Coin cell voltage
DDOTP
V
LICELL
ESD Ratings
V
Human Body Model(6)
Charge Device Model(6)
±2000
±500
V
ESD
Notes
6. ESD testing is performed in accordance with the Human Body Model (HBM) (CZAP = 100 pF, RZAP = 1500 ), and the Charge Device
Model (CDM), Robotic (CZAP = 4.0 pF).
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
General Product Characteristics
Thermal Characteristics
4.2
Thermal Characteristics
Table 6. Thermal Ratings
Symbol
Description (Rating)
Min.
Max.
Unit
THERMAL RATINGS
Ambient Operating Temperature Range
PF0100
PF0100A
PF0100AN
-40
-40
-40
85
85
105
TA
C
TJ
Operating Junction Temperature Range (7)
Storage Temperature Range
-40
-65
–
125
150
C
C
C
TST
TPPRT
Peak Package Reflow Temperature (8)(9)
Note 9
QFN56 THERMAL RESISTANCE AND PACKAGE DISSIPATION RATINGS
Junction to Ambient (10)(11)(12)
Natural Convection
Four layer board (2s2p)
Eight layer board (2s6p)
RJA
°C/W
°C/W
–
–
28
15
Junction to Ambient (@200 ft/min)(10)(12)
RJMA
Four layer board (2s2p)
–
–
–
22
10
RJB
Junction to Board(13)
°C/W
°C/W
RJCBOTTOM Junction to Case Bottom(14)
1.2
Junction to Package Top(15)
JT
–
2.0
°C/W
Natural Convection
Notes
7. Do not operate beyond 125 °C for extended periods of time. Operation above 150 °C may cause permanent damage to the IC. See
Table 7 for thermal protection features.
8. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause a malfunction or permanent damage to the device.
9. Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow
Temperature and Moisture Sensitivity Levels (MSL), Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes
and enter the core ID to view all orderable parts (i.e. MC33xxxD enter 33xxx), and review parametrics.
10. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance.
11. The Board uses the JEDEC specifications for thermal testing (and simulation) JESD51-7 and JESD51-5.
12. Per JEDEC JESD51-6 with the board horizontal.
13. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top
surface of the board near the package.
14. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1).
15. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per
JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT.
PF0100
Analog Integrated Circuit Device Data
12
Freescale Semiconductor
General Product Characteristics
Electrical Characteristics
4.2.1 Power Dissipation
During operation, the temperature of the die should not exceed the operating junction temperature noted in Table 6. To optimize
the thermal management and to avoid overheating, the PF0100 provides thermal protection. An internal comparator monitors the
die temperature. Interrupts THERM110I, THERM120I, THERM125I, and THERM130I will be generated when the respective
thresholds specified in Table 7 are crossed in either direction. The temperature range can be determined by reading the
THERMxxxS bits in register INTSENSE0.
In the event of excessive power dissipation, thermal protection circuitry will shut down the PF0100. This thermal protection will
act above the thermal protection threshold listed in Table 7. To avoid any unwanted power downs resulting from internal noise,
the protection is debounced for 8.0 ms. This protection should be considered as a fail-safe mechanism and therefore the system
should be configured such that this protection is not tripped under normal conditions.
Table 7. Thermal Protection Thresholds
Parameter
Thermal 110 °C Threshold (THERM110)
Min
Typ
Max
Units
100
110
115
120
2.0
110
120
125
130
–
120
130
135
140
4.0
°C
°C
°C
°C
°C
°C
Thermal 120 °C Threshold (THERM120)
Thermal 125 °C Threshold (THERM125)
Thermal 130 °C Threshold (THERM130)
Thermal Warning Hysteresis
Thermal Protection Threshold
130
140
150
4.3
Electrical Characteristics
4.3.1 General Specifications
Table 8. General PMIC Static Characteristics.
TMIN to TMAX (See Table 3), VIN = 2.8 to 4.5 V, VDDIO = 1.7 to 3.6 V, typical external component values and full load current
range, unless otherwise noted.
Pin Name
Parameter
Load Condition
Min
Max
Unit
VIL
VIH
–
0.0
0.8 * VSNVS
0.0
0.2 * VSNVS
V
V
V
V
V
V
V
V
V
V
V
V
V
V
PWRON
–
-2.0 mA
Open Drain
–
3.6
0.4
VOL
VOH
VIL
RESETBMCU
SCL
0.7* VIN
0.0
VIN
0.2 * VDDIO
3.6
VIH
–
0.8 * VDDIO
0.0
VIL
–
0.2 * VDDIO
3.6
VIH
–
0.8 * VDDIO
0.0
SDA
VOL
VOH
VOL
VOH
VOL
VOH
-2.0 mA
Open Drain
-2.0 mA
Open Drain
-2.0 mA
Open Drain
0.4
0.7*VDDIO
0.0
VDDIO
0.4
INTB
0.7* VIN
0.0
VIN
0.4
SDWNB
0.7* VIN
VIN
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
General Product Characteristics
Electrical Characteristics
Table 8. General PMIC Static Characteristics.
TMIN to TMAX (See Table 3), VIN = 2.8 to 4.5 V, VDDIO = 1.7 to 3.6 V, typical external component values and full load current
range, unless otherwise noted.
VIL
VIH
VIL
VIH
–
–
–
–
0.0
0.8 * VSNVS
0.0
0.2 * VSNVS
V
V
V
V
STANDBY
VDDOTP
3.6
0.3
1.7
1.1
PF0100
Analog Integrated Circuit Device Data
14
Freescale Semiconductor
General Product Characteristics
Electrical Characteristics
4.3.2 Current Consumption
Table 9. Current Consumption Summary
TMIN to TMAX (See Table 3), VIN = 3.6 V, VDDIO = 1.7 to 3.6 V, LICELL = 1.8 to 3.3 V, VSNVS = 3.0 V, typical external
component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VDDIO = 3.3 V, LICELL = 3.0 V,
VSNVS = 3.0 V and 25 °C, unless otherwise noted.
Mode
PF0100 Conditions
System Conditions
Typical
MAX
Unit
VSNVS from LICELL
Coin Cell
All other blocks off
VIN = 0.0 V
No load on VSNVS
4.0
7.0
A
(16),(18),(22)
VSNVSVOLT[2:0] = 110
VSNVS from VIN or LICELL
Wake-up from PWRON active
32 k RC on
All other blocks off
VIN UVDET
Off (17),(18)
MMPF0100
No load on VSNVS, PMIC able to wake-up
No load on VSNVS, PMIC able to wake-up
16
17
21
25
A
A
VSNVS from VIN or LICELL
Wake-up from PWRON active
32 k RC on
Off (17),(18)
MMPF0100A
All other blocks off
VIN UVDET
VSNVS from VIN
Wake-up from PWRON active
Trimmed reference active
SW3A/B PFM
Trimmed 16 MHz RC off
32 k RC on
122
122
220(21)
250(20)
No load on VSNVS. DDR memories in self
refresh
Sleep (18)
A
VREFDDR disabled
VSNVS from either VIN or LICELL
SW1A/B combined in PFM
SW1C in PFM
SW2 in PFM
SW3A/B combined in PFM
SW4 in PFM
No load on VSNVS. Processor enabled in
low power mode. All rails powered on
except boost (load = 0 mA)
297
297
450 (19)
Standby (18)
MMPF0100
A
SWBST off
1000 (21)
Trimmed 16 MHz RC enabled
Trimmed reference active
VGEN1-6 enabled
VREFDDR enabled
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
General Product Characteristics
Electrical Characteristics
Table 9. Current Consumption Summary (continued)
TMIN to TMAX (See Table 3), VIN = 3.6 V, VDDIO = 1.7 to 3.6 V, LICELL = 1.8 to 3.3 V, VSNVS = 3.0 V, typical external
component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VDDIO = 3.3 V, LICELL = 3.0 V,
VSNVS = 3.0 V and 25 °C, unless otherwise noted.
Mode
PF0100 Conditions
System Conditions
Typical
MAX
Unit
VSNVS from either VIN or LICELL
SW1A/B combined in PFM
SW1C in PFM
SW2 in PFM
SW3A/B combined in PFM
SW4 in PFM
No load on VSNVS. Processor enabled in
low power mode. All rails powered on
except boost (load = 0 mA)
297
297
450 (21)
550(20)
Standby (18)
MMPF0100A
A
SWBST off
Trimmed 16 MHz RC enabled
Trimmed reference active
VGEN1-6 enabled
VREFDDR enabled
Notes
16. Refer to Figure 4 for Coin Cell mode characteristics over temperature.
17. When VIN is below the UVDET threshold, in the range of 1.8 V VIN < 2.65 V, the quiescent current increases by 50 A, typically.
18. For PFM operation, headroom should be 300 mV or greater.
19. From 0 °C to 85 °C
20. From -40 °C to 105 °C, Applicable only to Extended Industrial parts.
21. From -40 °C to 85 °C, Applicable to Consumer, Industrial and Extended Industrial part numbers.
22. Additional current may be drawn in the coin cell mode when RESETBMCU is pulled up to VSNVS due an internal path from
RESETBMCU to VIN. The additional current is <30A with a pull up resistor of 100k. The i.MX6x processors have an internal pull up
from the POR_B pin to the VDD_SNVS_IN pin. For i.MX6x applications, if additional current in the coin cell mode is not desired, use an
external switch to disconnect the RESETBMCU path when VIN is removed. For non-i.MX6 applications, pull up RESETBMCU to a rail
that is off in the coin cell mode.
Coin Cell Mode
100
MMPF0100
10
MMPF0100A
1
‐40
‐20
0
20
40
60
80
Temperature(°C)
Figure 4. Coin cell Mode Current Vs Temperature
PF0100
Analog Integrated Circuit Device Data
16
Freescale Semiconductor
General Description
Features
5
General Description
The PF0100 is the Power Management Integrated Circuit (PMIC) designed primarily for use with Freescale’s i.MX6 series of
application processors.
5.1
Features
This section summarizes the PF0100 features.
• Input voltage range to PMIC: 2.8 - 4.5 V
• Buck regulators
•
Four to six channel configurable
• SW1A/B/C, 4.5 A (single); 0.3 to 1.875 V
• SW1A/B, 2.5 A (single/dual); SW1C 2.0 A (independent); 0.3 to 1.875 V
• SW2, 2.0 A; 0.4 to 3.3 V
• SW3A/B, 2.5 A (single/dual); 0.4 to 3.3 V
• SW3A, 1.25 A (independent); SW3B, 1.25 A (independent); 0.4 to 3.3 V
• SW4, 1.0 A; 0.4 to 3.3 V
• SW4, VTT mode provide DDR termination at 50% of SW3A
Dynamic voltage scaling
Modes: PWM, PFM, APS
Programmable output voltage
Programmable current limit
Programmable soft start
Programmable PWM switching frequency
Programmable OCP with fault interrupt
•
•
•
•
•
•
•
• Boost regulator
•
•
•
SWBST, 5.0 to 5.15 V, 0.6 A, OTG support
Modes: PFM and Auto
OCP fault interrupt
• LDOs
•
Six user programable LDO
• VGEN1, 0.80 to 1.55 V, 100 mA
• VGEN2, 0.80 to 1.55 V, 250 mA
• VGEN3, 1.8 to 3.3 V, 100 mA
• VGEN4, 1.8 to 3.3 V, 350 mA
• VGEN5, 1.8 to 3.3 V, 100 mA
• VGEN6, 1.8 to 3.3 V, 200 mA
Soft start
•
•
LDO/Switch supply
• VSNVS (1.0/1.1/1.2/1.3/1.5/1.8/3.0 V), 400 A
• DDR memory reference voltage
VREFDDR, 0.6 to 0.9 V, 10 mA
•
• 16 MHz internal master clock
• OTP(One time programmable) memory for device configuration
•
User programmable start-up sequence and timing
• Battery backed memory including coin cell charger
• I2C interface
• User programmable Standby, Sleep, and Off modes
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
General Description
Functional Block Diagram
5.2
Functional Block Diagram
MMPF0100 Functional Internal Block Diagram
OTP Startup Configuration
Power Generation
OTP Prototyping
Voltage
Switching Regulators
Linear Regulators
(Try before buy)
VGEN1
(0.8 to 1.55V, 100mA)
SW1A/B/C
(0.3 to 1.875V)
Configurable 4.5A or
2.5A+2.0A
Sequence and
timing
Phasing and
Frequency Selection
VGEN2
(0.8 to 1.55V, 250mA)
Bias & References
SW2
(0.4 to 3.3V, 2A)
Internal Core Voltage Reference
DDR Voltage Reference
VGEN3
(1.8 to 3.3V, 100mA)
VGEN4
(1.8 to 3.3V, 350mA)
SW3A/B
(0.4 to 3.3V)
Logic and Control
Configurable 2.5A or
1.25A+1.25A
VGEN5
Parallel MCU Interface
Regulator Control
(1.8 to 3.3V, 100mA)
I2C Communication & Registers
SW4
(0.4 to 3.3V, 1A)
VGEN6
(1.8 to 3.3V, 200mA)
Fault Detection and Protection
VSNVS
(1.0 to 3.0V, 400uA)
RTC supply with coin cell
charger
Boost Regulator
(5 to 5.15V, 600mA)
USB OTG Supply
Thermal
Current Limit
Short-Circuit
Figure 5. Functional Block Diagram
5.3
Functional Description
5.3.1 Power Generation
The PF0100 PMIC features four buck regulators (up to six independent outputs), one boost regulator, six general purpose LDOs,
one switch/LDO combination and a DDR voltage reference to supply voltages for the application processor and peripheral
devices.
The number of independent buck regulator outputs can be configured from four to six, thereby providing flexibility to operate with
higher current capability, or to operate as independent outputs for applications requiring more voltage rails with lower current
demands. Further, SW1 and SW3 regulators can be configured as single/dual phase and/or independent converters. One of the
buck regulators, SW4, can also operate as a tracking regulator when used for memory termination. The buck regulators provide
the supply to processor cores and to other low voltage circuits such as IO and memory. Dynamic voltage scaling is provided to
allow controlled supply rail adjustments for the processor cores and/or other circuitry.
Depending on the system power path configuration, the six general purpose LDO regulators can be directly supplied from the
main input supply or from the switching regulators to power peripherals, such as audio, camera, Bluetooth, Wireless LAN, etc. A
specific VREFDDR voltage reference is included to provide accurate reference voltage for DDR memories operating with or
without VTT termination. The VSNVS block behaves as an LDO, or as a bypass switch to supply the SNVS/SRTC circuitry on
the i.MX processors; VSNVS may be powered from VIN, or from a coin cell.
5.3.2 Control Logic
The PF0100 PMIC is fully programmable via the I2C interface. Additional communication is provided by direct logic interfacing
including interrupt and reset. Start-up sequence of the device is selected upon the initial OTP configuration explained in the Start-
up section, or by configuring the “Try Before Buy” feature to test different power up sequences before choosing the final OTP
configuration.
The PF0100 PMIC has the interfaces for the power buttons and dedicated signaling interfacing with the processor. It also ensures
supply of critical internal logic and other circuits from the coin cell in case of brief interruptions from the main battery. A charger
for the coin cell is included as well.
PF0100
Analog Integrated Circuit Device Data
18
Freescale Semiconductor
General Description
Functional Description
5.3.2.1
Interface Signals
PWRON
PWRON is an input signal to the IC that generates a turn-on event. It can be configured to detect a level, or an edge using the
PWRON_CFG bit. Refer to section Turn On Events for more details.
STANDBY
STANDBY is an input signal to the IC. When it is asserted the part enters standby mode and when de-asserted, the part exits
standby mode. STANDBY can be configured as active high or active low using the STANDBYINV bit. Refer to the section
Standby Mode for more details.
Note: When operating the PMIC at VIN 2.85 V and VSNVS is programmed for a 3.0 V output, a coin cell must be present to
provide VSNVS, or the PMIC will not reliably enter and exit the STANDBY mode.
RESETBMCU
RESETBMCU is an open-drain, active low output configurable for two modes of operation. In its default mode, it is de-asserted
2.0 to 4.0 ms after the last regulator in the start-up sequence is enabled; refer to Figure 6 as an example. In this mode, the signal
can be used to bring the processor out of reset, or as an indicator that all supplies have been enabled; it is only asserted for a
turn-off event.
When configured for its fault mode, RESETBMCU is de-asserted after the start-up sequence is completed only if no faults
occurred during start-up. At anytime, if a fault occurs and persists for 1.8 ms typically, RESETBMCU is asserted, LOW. The
PF0100 is turned off if the fault persists for more than 100 ms typically. The PWRON signal restarts the part, though if the fault
persists, the sequence described above will be repeated. To enter the fault mode, set bit OTP_PG_EN of register
OTP PWRGD EN to “1”. This register, 0xE8, is located on Extended Page 1 of the register map. To test the fault mode, the bit
may be set during TBB prototyping, or the mode may be permanently chosen by programming OTP fuses.
SDWNB
SDWNB is an open-drain, active low output that notifies the processor of an imminent PMIC shut down. It is asserted low for one
32 kHz clock cycle before powering down and is then de-asserted in the OFF state.
INTB
INTB is an open-drain, active low output. It is asserted when any fault occurs, provided that the fault interrupt is unmasked. INTB
is de-asserted after the fault interrupt is cleared by software, which requires writing a “1” to the fault interrupt bit.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
Functional Block Requirements and Behaviors
Start-up
6
Functional Block Requirements and Behaviors
6.1
Start-up
The PF0100 can be configured to start-up from either the internal OTP configuration, or with a hard-coded configuration built in
to the device. The internal hard-coded configuration is enabled by connecting the VDDOTP pin to VCOREDIG through a
100 kohm resistor. The OTP configuration is enabled by connecting VDDOTP to GND.
For NP devices, selecting the OTP configuration causes the PF0100 to not start-up. However, the PF0100 can be controlled
through the I2C port for prototyping and programming. Once programmed, the NP device will startup with the customer
programmed configuration.
6.1.1 Device Start-up Configuration
Table 10 shows the Default Configuration which can be accessed on all devices as described above, as well as the pre-
programmed OTP configurations.
Table 10. Start-up Configuration
Default
Configuration
Pre-programmed OTP Configuration
Registers
All Devices
F0
F1(23)
F2(23)
F3
F4
Default I2C Address
VSNVS_VOLT
SW1AB_VOLT
SW1AB_SEQ
SW1C_VOLT
SW1C_SEQ
0x08
0x08
3.0 V
1.375 V
1
0x08
0x08
0x08
0x08
3.0 V
3.0 V
3.0 V
3.0 V
3.0 V
1.375 V
1.375 V
1.375 V
1.375 V
1.375 V
1
1
1
2
2
1.375 V
1.375 V
2
1.375 V
1.375 V
1.375 V
1.375 V
1
1
1
2
2
SW2_VOLT
3.0 V
3.3 V
5
3.15 V
3.15 V
3.15 V
3.15 V
SW2_SEQ
2
2
2
1
1
SW3A_VOLT
SW3A_SEQ
1.5 V
1.5 V
3
1.2 V
1.5 V
1.2 V
1.5 V
3
4
4
4
4
SW3B_VOLT
SW3B_SEQ
1.5 V
1.5 V
3
1.2 V
1.5 V
1.2 V
1.5 V
3
4
4
4
4
SW4_VOLT
1.8 V
3.15 V
6
1.8 V
1.8 V
1.8 V
1.8 V
SW4_SEQ
3
3
3
3
3
SWBST_VOLT
SWBST_SEQ
VREFDDR_SEQ
VGEN1_VOLT
VGEN1_SEQ
VGEN2_VOLT
VGEN2_SEQ
VGEN3_VOLT
VGEN3_SEQ
-
5.0 V
13
5.0 V
5.0 V
5.0 V
5.0 V
-
6
6
6
6
3
3
4
4
4
4
-
1.5 V
9
1.2 V
1.2 V
1.2 V
1.2 V
-
4
-
4
-
4
-
4
-
1.5 V
1.5 V
10
2
-
-
-
-
-
2.5 V
11
-
-
-
-
-
-
-
-
-
PF0100
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
Functional Block Requirements and Behaviors
Start-up
Table 10. Start-up Configuration
Default
Configuration
Pre-programmed OTP Configuration
Registers
All Devices
F0
F1(23)
F2(23)
F3
F4
VGEN4_VOLT
1.8 V
1.8 V
1.8 V
1.8 V
1.8 V
1.8 V
VGEN4_SEQ
3
2.5 V
3
7
2.8 V
3
3
3
3
VGEN5_VOLT
VGEN5_SEQ
2.5 V
2.5 V
2.5 V
2.5 V
12
5
5
5
5
VGEN6_VOLT
VGEN6_SEQ
2.8 V
3
3.3 V
-
-
-
-
-
-
-
8
-
PU CONFIG, SEQ_CLK_SPEED
PU CONFIG, SWDVS_CLK
PU CONFIG, PWRON
SW1AB CONFIG
SW1C CONFIG
SW2 CONFIG
1.0 ms
6.25 mV/s
2.0 ms
1.5625 mV/s
1.0 ms
1.0 ms
12.5 mV/s
1.0 ms
12.5 mV/s
1.0 ms
12.5 mV/s
12.5 mV/s
Level sensitive
SW1AB Single Phase, SW1C Independent Mode, 2.0 MHz
2.0 MHz
2.0 MHz
SW3A CONFIG
SW3B CONFIG
SW4 CONFIG
SW3AB Single Phase, 2.0 MHz
2.0 MHz
No VTT, 2.0 MHz
PG EN
RESETBMCU in Default Mode
Notes
23. For designs using the i.MX 6-SoloLite, it is recommended to use the F3 OTP option instead of the F1 OTP option and F4 OTP option
instead of the F2 OTP option
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
Functional Block Requirements and Behaviors
Start-up
LICELL
UVDET
tr1
VIN
td1
1V
td2
tr2
VSNVS
td3
tr3
PWRON
SW1A/B
SW1C
td4
tr3
SW2
VGEN2
SW3A/B
td4
tr3
SW4
VREFDDR
VGEN4
VGEN5
td5
tr4
VGEN6
RESETBMCU
*VSNVS will start from 1.0 V if LICELL is valid before VIN.
Figure 6. Default Start-up Sequence
Table 11. Default Start-up Sequence Timing
Parameter
Description
Min
Typ
Max
Unit
tD1
tR1
tD2
tR2
Turn-on delay of VSNVS (24)
Rise time of VSNVS
–
–
–
–
5.0
3.0
–
–
–
–
ms
ms
ms
ms
User determined delay
Rise time of PWRON
1.0
(25)
Turn-on delay of first regulator
SEQ_CLK_SPEED[1:0] = 00
SEQ_CLK_SPEED[1:0] = 01(26)
SEQ_CLK_SPEED[1:0] = 10
SEQ_CLK_SPEED[1:0] = 11
–
–
–
–
2.0
2.5
4.0
7.0
–
–
–
–
tD3
ms
PF0100
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
Functional Block Requirements and Behaviors
Start-up
Table 11. Default Start-up Sequence Timing
Parameter
Description
Min
Typ
Max
Unit
tR3
Rise time of regulators(27)
Delay between regulators
–
0.2
–
ms
SEQ_CLK_SPEED[1:0] = 00
SEQ_CLK_SPEED[1:0] = 01
SEQ_CLK_SPEED[1:0] = 10
SEQ_CLK_SPEED[1:0] = 11
Rise time of RESETBMCU
–
–
–
–
–
–
0.5
1.0
2.0
4.0
0.2
2.0
–
–
–
–
–
–
tD4
ms
tR4
tD5
ms
ms
Turn-on delay of RESETBMCU
Notes
24. Assumes LICELL voltage is valid before VIN is applied. If LICELL is not valid before VIN is applied then VSNVS turn-on delay may
extend to a maximum of 24 ms.
25. Depends on the external signal driving PWRON.
26. Default configuration.
27. Rise time is a function of slew rate of regulators and nominal voltage selected.
6.1.2 One Time Programmability (OTP)
OTP allows the programming of start-up configurations for a variety of applications. Before permanently programming the IC by
programming fuses, a configuration may be prototyped by using the “Try Before Buy” (TBB) feature. Further, an error correction
code(ECC) algorithm is available to correct a single bit error and to detect multiple bit errors when fuses are programmed.
The parameters that can be configured by OTP are listed below.
• General: I2C slave address, PWRON pin configuration, start-up sequence and timing
• Buck regulators: Output voltage, dual/single phase or independent mode configuration, switching frequency, and soft
start ramp rate
• Boost regulator and LDOs: Output voltage
NOTE: When prototyping or programming fuses, the user must ensure that register settings are consistent with the hardware
configuration. This is most important for the buck regulators, where the quantity, size, and value of the inductors depend on the
configuration (single/dual phase or independent mode) and the switching frequency. Additionally, if an LDO is powered by a buck
regulator, it will be gated by the buck regulator in the start-up sequence.
6.1.2.1
Start-up Sequence and Timing
Each regulator has 5-bits allocated to program its start-up time slot from a turn on event; therefore, each can be placed from
position one to thirty-one in the start-up sequence. The all zeros code indicates that a regulator is not part of the start-up
sequence and will remain off. See Table 12. The delay between each position is equal; however, four delay options are available.
See Table 13. The start-up sequence will terminate at the last programmed regulator.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
Functional Block Requirements and Behaviors
Start-up
Table 12. Start-up Sequence
SWxx_SEQ[4:0]/
VGENx_SEQ[4:0]/
VREFDDR_SEQ[4:0]
Sequence
00000
Off
00001
SEQ_CLK_SPEED[1:0] * 1
00010
SEQ_CLK_SPEED[1:0] * 2
*
*
*
*
*
*
*
*
11111
SEQ_CLK_SPEED[1:0] * 31
Table 13. Start-up Sequence Clock Speed
SEQ_CLK_SPEED[1:0]
Time (s)
00
01
10
11
500
1000
2000
4000
6.1.2.2
PWRON Pin Configuration
The PWRON pin can be configured as either a level sensitive input (PWRON_CFG = 0), or as an edge sensitive input
(PWRON_CFG = 1). As a level sensitive input, an active high signal turns on the part and an active low signal turns off the part,
or puts it into Sleep mode. As an edge sensitive input, such as when connected to a mechanical switch, a falling edge will turn
on the part and if the switch is held low for greater than or equal to 4.0 seconds, the part will turn off or enter Sleep mode.
Table 14. PWRON Configuration
PWRON_CFG
Mode
PWRON pin HIGH = ON
PWRON pin LOW = OFF or Sleep mode
0
PWRON pin pulled LOW momentarily = ON
PWRON pin LOW for 4.0 seconds = OFF or Sleep mode
1
2
6.1.2.3
I C Address Configuration
The I2C device address can be programmed from 0x08 to 0x0F. This allows flexibility to change the I2C address to avoid bus
conflicts. Address bit, I2C_SLV_ADDR[3] in OTP_I2C_ADDR register is hard coded to “1” while the lower three LSBs of the I2C
address (I2C_SLV_ADDR[2:0]) are programmable as shown in Table 15.
Table 15. I2C Address Configuration
I2C_SLV_ADDR[3]
Hard Coded
I2C Device Address
(Hex)
I2C_SLV_ADDR[2:0]
1
1
1
000
001
010
0x08
0x09
0x0A
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
24
Functional Block Requirements and Behaviors
Start-up
Table 15. I2C Address Configuration
I2C_SLV_ADDR[3]
I2C_SLV_ADDR[2:0]
Hard Coded
I2C Device Address
(Hex)
1
1
1
1
1
011
100
101
110
111
0x0B
0x0C
0x0D
0x0E
0x0F
6.1.2.4
Soft Start Ramp Rate
The start-up ramp rate or soft start ramp rate can be chosen from the same options as shown in Dynamic Voltage Scaling.
6.1.3 OTP Prototyping
Before permanently programming fuses, it is possible to test the desired configuration by using the “Try Before Buy” feature. With
this feature, the configuration is loaded from the OTP registers. These registers merely serve as temporary storage for the values
to be written to the fuses, for the values read from the fuses, or for the values read from the default configuration. To avoid
confusion, these registers will be referred to as the TBBOTP registers. The portion of the register map that concerns OTP is
shown in Table 137 and Table 138.
The contents of the TBBOTP registers are initialized to zero when a valid VIN is first applied. The values that are then loaded
into the TBBOTP registers depend on the setting of the VDDOTP pin and on the value of the TBB_POR and FUSE_POR_XOR
bits. Refer to Table 16.
• If VDDOTP = VCOREDIG (1.5 V), the values are loaded from the default configuration.
• If VDDOTP = 0.0 V, TBB_POR = 0 and FUSE_POR_XOR = 1, the values are loaded from the fuses. In the MMPF0100,
FUSE_POR1, FUSE_POR2, and FUSE_POR3 are XOR’ed into the FUSE_POR_XOR bit. The FUSE_POR_XOR has to
be 1 for fuses to be loaded. This can be achieved by setting any one or all of the FUSE_PORx bits. In the MMPF0100A,
the XOR function is removed. It is required to set all of the FUSE_PORx bits to be able to load the fuses.
• If VDDOTP = 0.0 V, TBB_POR = 0 and FUSE_POR_XOR = 0, the TBBOTP registers remain initialized at zero.
The initial value of TBB_POR is always “0”; only when VDDOTP = 0.0 V and TBB_POR is set to “1” are the values from the
TBBOTP registers maintained and not loaded from a different source.
The contents of the TBBOTP registers are modified by I2C. To communicate with I2C, VIN must be valid and VDDIO, to which
SDA and SCL are pulled up, must be powered by a 1.7 to 3.6 V supply. VIN, or the coin cell voltage must be valid to maintain
the contents of the registers. To power on with the contents of the TBBOTP registers, the following conditions must exist; VIN is
valid, VDDOTP = 0.0 V, TBB_POR = 1 and there is a valid turn-on event. Refer to the application note AN4536 for an example
of prototyping.
6.1.4 Reading OTP Fuses
As described in the previous section, the contents of the fuses are loaded to the TBBOTP registers when the following conditions
are met; VIN is valid, VDDOTP = 0.0 V, TBB_POR = 0 and FUSE_POR_XOR = 1. If ECC were enabled at the time the fuses
were programmed, the error corrected values can be loaded into the TBBOTP registers if desired. Once the fuses are loaded
and a turn-on event occurs, the PMIC will power on with the configuration programmed in the fuses. For more details on reading
the OTP fuses, see application note AN4536.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
Functional Block Requirements and Behaviors
16 MHz and 32 kHz Clocks
6.1.5 Programming OTP Fuses
The parameters that can be programmed are shown in the TBBOTP registers in the Extended Page 1 of the register map. The
PF0100 offers ECC, the control registers for which functions are located in Extended Page 2 of the register map. There are ten
banks of twenty-six fuses each that can be programmed. Programming the fuses requires an 8.25 V, 100 mA supply powering
the VDDOTP pin, bypassed with 10 to 20 F of capacitance. For more details on programming the OTP fuses, see application
note AN4536.
Table 16. Source of Start-up Sequence
VDDOTP(V)
TBB_POR FUSE_POR_XOR
Start-up Sequence
0
0
0
0
1
x
0
1
x
x
None
OTP fuses
0
TBBOTP registers
Factory defined
1.5
6.2
16 MHz and 32 kHz Clocks
There are two clocks: a trimmed 16 MHz, RC oscillator and an untrimmed 32 kHz, RC oscillator. The 16 MHz oscillator is
specified within -8.0/+8.0%. The 32 kHz untrimmed clock is only used in the following conditions:
• VIN < UVDET
• All regulators are in SLEEP mode
• All regulators are in PFM switching mode
A 32 kHz clock, derived from the 16 MHz trimmed clock, is used when accurate timing is needed under the following conditions:
• During start-up, VIN > UVDET
• PWRON_CFG = 1, for power button debounce timing
In addition, when the 16 MHz is active in the ON mode, the debounce times in Table 27 are referenced to the 32 kHz derived
from the 16 MHz clock. The exceptions are the LOWVINI and PWRONI interrupts, which are referenced to the 32 kHz untrimmed
clock.
Table 17. 16 MHz Clock Specifications
TMIN to TMAX (See Table 3), VIN = 2.8 to 4.5 V, LICELL = 1.8 to 3.3 V and typical external component values. Typical values are
characterized at VIN = 3.6 V, LICELL = 3.0 V, and 25 °C, unless otherwise noted.
Parameters
Symbol
Min
Typ
Max
Units
Operating Voltage From VIN
16 MHz Clock Frequency
VIN16MHz
f16MHZ
f2MHZ
2.8
–
16
–
4.5
V
14.7
1.84
17.2
2.15
MHz
MHz
2.0 MHz Clock Frequency (28)
Notes
28. 2.0 MHz clock is derived from the 16 MHz clock.
6.2.1 Clock adjustment
The 16 MHz clock and hence the switching frequency of the regulators, can be adjusted to improve the noise integrity of the
system. By changing the factory trim values of the 16MHz clock, the user may add an offset as small as 3.0% of the nominal
frequency. Contact your Freescale representative for detailed information on this feature.
PF0100
Analog Integrated Circuit Device Data
26
Freescale Semiconductor
Functional Block Requirements and Behaviors
Bias and References Block Description
6.3
Bias and References Block Description
6.3.1 Internal Core Voltage References
All regulators use the main bandgap as the reference. The main bandgap is bypassed with a capacitor at VCOREREF. The
bandgap and the rest of the core circuitry are supplied from VCORE. The performance of the regulators is directly dependent on
the performance of the bandgap. No external DC loading is allowed on VCORE, VCOREDIG, or VCOREREF. VCOREDIG is
kept powered as long as there is a valid supply and/or valid coin cell. Table 18 shows the main characteristics of the core circuitry.
Table 18. Core Voltages Electrical Specifications(30)
TMIN to TMAX (See Table 3), VIN = 2.8 to 4.5 V, LICELL = 1.8 to 3.3 V, and typical external component values. Typical values are
characterized at VIN = 3.6 V, LICELL = 3.0 V, and 25 °C, unless otherwise noted.
Parameters
Symbol
Min
Typ
Max
Units
VCOREDIG (DIGITAL CORE SUPPLY)
Output Voltage
ON mode (29)
Coin cell mode and OFF
VCOREDIG
–
–
1.5
1.3
–
–
V
VCORE (ANALOG CORE SUPPLY)
Output Voltage
ON mode and charging(29)
OFF and Coin cell mode
VCORE
–
–
2.775
0.0
–
–
V
VCOREREF (BANDGAP / REGULATOR REFERENCE)
Output Voltage(29)
Absolute Accuracy
Temperature Drift
Notes
VCOREREF
VCOREREFACC
VCOREREFTACC
–
–
–
1.2
0.5
–
–
–
V
%
%
0.25
29. 3.0 V < VIN < 4.5 V, no external loading on VCOREDIG, VCORE, or VCOREREF. Extended operation down to UVDET, but no system
malfunction.
30. For information only.
6.3.1.1
External Components
Table 19. External Components for Core Voltages
Regulator
Capacitor Value (F)
VCOREDIG
VCORE
1.0
1.0
VCOREREF
0.22
6.3.2 VREFDDR Voltage Reference
VREFDDR is an internal PMOS half supply voltage follower capable of supplying up to 10 mA. The output voltage is at one half
the input voltage. Its typically used as the reference voltage for DDR memories. A filtered resistor divider is utilized to create a
low frequency pole. This divider then utilizes a voltage follower to drive the load.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
Functional Block Requirements and Behaviors
Bias and References Block Description
VINREFDDR
VINREFDDR
CHALF1
100 nf
VHALF
_
+
CHALF2
100 nf
Discharge
VREFDDR
VREFDDR
CREFDDR
1.0 uf
Figure 7. VREFDDR Block Diagram
6.3.2.1
VREFDDR Control Register
The VREFDDR voltage reference is controlled by a single bit in VREFDDCRTL register in Table 20.
Table 20. Register VREFDDCRTL - ADDR 0x6A
Name
UNUSED
Bit #
R/W Default
Description
3:0
–
R/W
–
0x00
0x00
0x00
UNUSED
Enable or disables VREFDDR output voltage
0 = VREFDDR Disabled
VREFDDREN
4
1 = VREFDDR Enabled
UNUSED
7:5
UNUSED
External Components
Table 21. VREFDDR External Components(31)
Capacitor
Capacitance (F)
VINREFDDR(32) to VHALF
VHALF to GND
VREFDDR
0.1
0.1
1.0
Notes
31. Use X5R or X7R capacitors.
32. VINREFDDR to GND, 1.0 F minimum
capacitance is provided by buck regulator output.
PF0100
Analog Integrated Circuit Device Data
28
Freescale Semiconductor
Functional Block Requirements and Behaviors
Bias and References Block Description
VREFDDR Specifications
Table 22. VREFDDR Electrical Characteristics
TMIN to TMAX (See Table 3), VIN = 3.6 V, IREFDDR = 0.0 mA, VINREFDDR = 1.5 V and typical external component values, unless
otherwise noted. Typical values are characterized at VIN = 3.6 V, IREFDDR = 0.0 mA, VINREFDDR = 1.5 V, and 25 °C, unless
otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VREFDDR
Operating Input Voltage Range
Operating Load Current Range
Current Limit
VINREFDDR
IREFDDR
1.2
0.0
–
–
1.8
10
V
mA
IREFDDRLIM
IREFDDRQ
10.5
–
15
25
–
mA
I
REFDDR when VREFDDR is forced to VINREFDDR/4
Quiescent Current(33)
8.0
A
ACTIVE MODE – DC
Output Voltage
1.2 V < VINREFDDR < 1.8 V
0.0 mA < IREFDDR < 10 mA
VREFDDR
–
VINREFDDR/2
–
V
Output Voltage Tolerance (TA = -40 to 85 °C)
1.2 V < VINREFDDR < 1.8 V
VREFDDRTOL
–1.0
–
1.0
%
0.6 mA IREFDDR 10 mA
Output Voltage Tolerance (TA = -40 to 105 °C), Applicable only to
the Extended Industrial version
VREFDDRTOL
–1.2
–
–
1.2
–
%
1.2 V < VINREFDDR < 1.8 V
0.6 mA IREFDDR 10 mA
Load Regulation
1.0 mA < IREFDDR < 10 mA
1.2 V < VINREFDDR < 1.8 V
VREFDDRLOR
0.40
mV/mA
ACTIVE MODE – AC
Turn-on Time
Enable to 90% of end value
tONREFDDR
–
–
–
–
100
10
s
V
INREFDDR = 1.2 V, 1.8 V
I
REFDDR = 0.0 mA
Turn-Off Time
Disable to 10% of initial value
INREFDDR = 1.2 V, 1.8 V
REFDDR = 0.0 mA
tOFFREFDDR
ms
V
I
Start-up Overshoot
INREFDDR = 1.2 V, 1.8 V
REFDDR = 0.0 mA
V
I
VREFDDROSH
–
–
1.0
5.0
6.0
–
%
Transient Load Response
VREFDDRTLR
mV
V
INREFDDR = 1.2 V, 1.8 V
Notes
33. When VREFDDR is off there is a quiescent current of 1.5 A typical.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
Functional Block Requirements and Behaviors
Power Generation
6.4
Power Generation
6.4.1 Modes of Operation
The operation of the PF0100 can be reduced to five states, or modes: ON, OFF, Sleep, Standby, and Coin Cell. Figure 8 shows
the state diagram of the PF0100, along with the conditions to enter and exit from each state.
Coin Cell
VIN < UVDET
VIN < UVDET
VIN > UVDET
PWRON = 0 held >= 4.0 sec
Any SWxOMODE bits=1
& PWRONRSTEN = 1
(PWRON_CFG=1)
Thermal shutdown
OFF
PWRON=1
& VIN > UVDET
(PWRON_CFG = 0)
Or
VIN < UVDET
Sleep
PWRON = 0
Any SWxOMODE bits=1
(PWRON_CFG=0)
Or
PWRON=0 held >= 4.0 sec
Any SWxOMODE bits=1
& PWRONRSTEN = 1
(PWRON_CFG=1)
PWRON= 0 < 4.0 sec
& VIN > UVDET
(PWRON_CFG=1)
PWRON = 0
All SWxOMODE bits= 0
(PWRON_CFG = 0)
Or
VIN < UVDET
PWRON = 0
Any SWxOMODE bits=1
(PWRON_CFG=0)
Or
PWRON=0 held >= 4.0 sec
Any SWxOMODE bits=1
& PWRONRSTEN = 1
(PWRON_CFG=1)
PWRON = 0 held >= 4.0 sec
All SWxOMODE bits= 0
& PWRONRSTEN = 1
(PWRON_CFG = 1)
PWRON=1
& VIN > UVDET
(PWRON_CFG =0)
Or
PWRON= 0 < 4.0 sec
& VIN > UVDET
(PWRON_CFG=1)
ON
Thermal shudown
PWRON = 0
All SWxOMODE bits= 0
(PWRON_CFG = 0)
Or
STANDBY asserted
STANDBY de-asserted
PWRON = 0 held >= 4.0 sec
All SWxOMODE bits= 0
& PWRONRSTEN = 1
(PWRON_CFG = 1)
Thermal shutdown
Standby
Figure 8. State Diagram
To complement the state diagram in Figure 8, a description of the states is provided in following sections. Note that VIN must
exceed the rising UVDET threshold to allow a power up. Refer to Table 29 for the UVDET thresholds. Additionally, I2C control is
not possible in the Coin Cell mode and the interrupt signal, INTB, is only active in Sleep, Standby, and ON states.
6.4.1.1
ON Mode
The PF0100 enters the On mode after a turn-on event. RESETBMCU is de-asserted, high, in this mode of operation.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
30
Functional Block Requirements and Behaviors
Power Generation
6.4.1.2
OFF Mode
The PF0100 enters the Off mode after a turn-off event. A thermal shutdown event also forces the PF0100 into the Off mode. Only
VCOREDIG and VSNVS are powered in the mode of operation. To exit the Off mode, a valid turn-on event is required.
RESETBMCU is asserted, LOW, in this mode.
6.4.1.3
Standby Mode
• Depending on STANDBY pin configuration, Standby is entered when the STANDBY pin is asserted. This is typically used
for low-power mode of operation.
• When STANDBY is de-asserted, Standby mode is exited.
A product may be designed to go into a Low-power mode after periods of inactivity. The STANDBY pin is provided for board level
control of going in and out of such deep sleep modes (DSM).
When a product is in DSM, it may be able to reduce the overall platform current by lowering the regulator output voltage, changing
the operating mode of the regulators or disabling some regulators. The configuration of the regulators in Standby is pre-
programmed through the I2C interface.
Note that the STANDBY pin is programmable for Active High or Active Low polarity, and that decoding of a Standby event will
take into account the programmed input polarity as shown in Table 23. When the PF0100 is powered up first, regulator settings
for the Standby mode are mirrored from the regulator settings for the ON mode. To change the STANDBY pin polarity to Active
Low, set the STANDBYINV bit via software first, and then change the regulator settings for Standby mode as required. For
simplicity, STANDBY will generally be referred to as active high throughout this document.
Table 23. Standby Pin and Polarity Control
STANDBY (Pin)(35)
STANDBYINV (I2C bit)(36)
STANDBY Control (34)
0
0
1
0
1
0
1
1
0
0
1
1
Notes
34. STANDBY = 0: System is not in Standby, STANDBY = 1: System is in Standby
35. The state of the STANDBY pin only has influence in On mode.
36. Bit 6 in Power Control Register (ADDR - 0x1B)
Since STANDBY pin activity is driven asynchronously to the system, a finite time is required for the internal logic to qualify and
respond to the pin level changes. A programmable delay is provided to hold off the system response to a Standby event. This
allows the processor and peripherals some time after a standby instruction has been received to terminate processes to facilitate
seamless entering into Standby mode.
When enabled (STBYDLY = 01, 10, or 11) per Table 24, STBYDLY will delay the Standby initiated response for the entire IC,
until the STBYDLY counter expires.
An allowance should be made for three additional 32 k cycles required to synchronize the Standby event.
Table 24. STANDBY Delay - Initiated Response
STBYDLY[1:0](37)
Function
00
01
10
11
No Delay
One 32 k period (default)
Two 32 k periods
Three 32 k periods
Notes
37. Bits [5:4] in Power Control Register (ADDR - 0x1B)
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
Functional Block Requirements and Behaviors
Power Generation
6.4.1.4
Sleep Mode
• Depending on PWRON pin configuration, Sleep mode is entered when PWRON is de-asserted and SWxOMODE bit is set.
• To exit Sleep mode, assert the PWRON pin.
In the Sleep mode, the regulator will use the set point as programmed by SW1xOFF[5:0] for SW1A/B/C and by SWxOFF[6:0] for
SW2, SW3A/B, and SW4. The activated regulators will maintain settings for this mode and voltage until the next turn-on event.
Table 25 shows the control bits in Sleep mode. During Sleep mode, interrupts are active and the INTB pin will report any
unmasked fault event.
Table 25. Regulator Mode Control
SWxOMODE
Off Operational Mode (Sleep) (38)
0
1
Off
PFM
Notes
38. For sleep mode, an activated switching regulator, should use the off
mode set point as programmed by SW1xOFF[5:0] for SW1A/B/C and
SWxOFF[6:0] for SW2, SW3A/B, and SW4.
6.4.1.5
Coin Cell Mode
In the Coin Cell state, the coin cell is the only valid power source (VIN = 0.0 V) to the PMIC. No turn-on event is accepted in the
Coin Cell state. Transition to the OFF state requires that VIN surpasses UVDET threshold. RESETBMCU is held low in this mode.
If the coin cell is depleted, a complete system reset will occur. At the next application of power and the detection of a Turn-on
event, the system will be re-initialized with all I2C bits including, those that reset on COINPORB are restored to their default
states.
PF0100
Analog Integrated Circuit Device Data
32
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.2 State Machine Flow Summary
Table 26 provides a summary matrix of the PF0100 flow diagram to show the conditions needed to transition from one state to
another.
Table 26. State Machine Flow Summary
Next State
STATE
OFF
X
Coin cell
IN < UVDET
X
Sleep
Standby
ON
PWRON_CFG = 0
PWRON = 1 & VIN > UVDET
or
OFF
Coin cell
Sleep
V
X
X
X
X
X
X
PWRON_CFG = 1
PWRON = 0 < 4.0 s
& VIN > UNDET
V
IN > UVDET
X
Thermal Shutdown
PWRON_CFG = 0
PWRON = 1 & VIN > UVDET
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
Any SWxOMODE = 1 &
PWRONRSTEN = 1
VIN < UVDET
PWRON_CFG = 1
PWRON = 0 < 4.0 s &
V
IN > UNDET
Thermal Shutdown
PWRON_CFG = 0
PWRON = 0
Any SWxOMODE = 1
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
Any SWxOMODE = 1 &
PWRONRSTEN = 1
PWRON_CFG = 0
PWRON = 0
All SWxOMODE = 0
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
All SWxOMODE = 0 &
PWRONRSTEN = 1
Standby
V
IN < UVDET
X
Standby de-asserted
Thermal Shutdown
PWRON_CFG = 0
PWRON = 0
Any SWxOMODE = 1
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
Any SWxOMODE = 1 &
PWRONRSTEN = 1
PWRON_CFG = 0
PWRON = 0
All SWxOMODE = 0
or
PWRON_CFG = 1
PWRON = 0 ≥ 4.0 s
All SWxOMODE = 0 &
PWRONRSTEN = 1
Standby
asserted
ON
V
IN < UVDET
X
6.4.2.1
Turn On Events
From OFF and Sleep modes, the PMIC is powered on by a turn-on event. The type of Turn-on event depends on the configuration
of PWRON. PWRON may be configured as an active high when PWRON_CFG = 0, or as the input of a mechanical switch when
PWRON_CFG = 1. VIN must be greater than UVDET for the PMIC to turn-on. When PWRON is configured as an active high and
PWRON is high (pulled up to VSNVS) before VIN is valid, a VIN transition from 0.0 V to a voltage greater than UVDET is also a
Turn-on event. See the State diagram, Figure 8, and the Table 26 for more details. Any regulator enabled in the Sleep mode will
remain enabled when transitioning from Sleep to ON, i.e., the regulator will not be turned off and then on again to match the start-
up sequence. The following is a more detailed description of the PWRON configurations:
• If PWRON_CFG = 0, the PWRON signal is high and VIN > UVDET, the PMIC will turn on; the interrupt and sense bits,
PWRONI and PWRONS respectively, will be set.
• If PWRON_CFG = 1, VIN > UVDET and PWRON transitions from high to low, the PMIC will turn on; the interrupt and sense
bits, PWRONI and PWRONS respectively, will be set.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
33
Functional Block Requirements and Behaviors
Power Generation
The sense bit will show the real time status of the PWRON pin. In this configuration, the PWRON input can be a mechanical
switch debounced through a programmable debouncer, PWRONDBNC[1:0], to avoid a response to a very short (i.e.,
unintentional) key press. The interrupt is generated for both the falling and the rising edge of the PWRON pin. By default, a 30 ms
interrupt debounce is applied to both falling and rising edges. The falling edge debounce timing can be extended with
PWRONDBNC[1:0] as defined in the table below. The interrupt is cleared by software, or when cycling through the OFF mode.
Table 27. PWRON Hardware Debounce Bit Settings
Turn On
Debounce (ms)
Falling Edge INT
Debounce (ms)
Rising Edge INT
Debounce (ms)
Bits
State
00
01
10
11
0.0
31.25
125
31.25
31.25
125
31.25
31.25
31.25
31.25
PWRONDBNC[1:0]
Notes
750
750
39. The sense bit, PWRONS, is not debounced and follows the state of the PWRON pin.
6.4.2.2
Turn Off Events
PWRON Pin
The PWRON pin is used to power off the PF0100. The PWRON pin can be configured with OTP to power off the PMIC under
the following two conditions:
1. PWRON_CFG bit = 0, SWxOMODE bit = 0 and PWRON pin is low.
2. PWRON_CFG bit = 1, SWxOMODE bit = 0, PWRONRSTEN = 1 and PWRON is held low for longer than 4.0
seconds. Alternatively, the system can be configured to restart automatically by setting the RESTARTEN bit.
Thermal Protection
If the die temperature surpasses a given threshold, the thermal protection circuit will power off the PMIC to avoid damage. A turn-
on event will not power on the PMIC while it is in thermal protection. The part will remain in Off mode until the die temperature
decreases below a given threshold. There are no specific interrupts related to this other than the warning interrupt. See Power
Dissipation section for more detailed information.
Undervoltage Detection
When the voltage at VIN drops below the undervoltage falling threshold, UVDET, the state machine will transition to the Coin Cell
mode.
6.4.3 Power Tree
The PF0100 PMIC features six buck regulators, one boost regulator, six general purpose LDOs, one switch/LDO combination,
and a DDR voltage reference to supply voltages for the application processor and peripheral devices. The buck regulators as
well as the boost regulator are supplied directly from the main input supply (VIN). The inputs to all of the buck regulators must be
tied to VIN, whether they are powered on or off. The six general use LDO regulators are directly supplied from the main input
supply or from the switching regulators depending on the application requirements. Since VREFDDR is intended to provide DDR
memory reference voltage, it should be supplied by any rail supplying voltage to DDR memories; the typical application
recommends the use of SW3 as the input supply for VREFDDR. VSNVS is supplied by either the main input supply or the coin
cell. Refer to Table 28 for a summary of all power supplies provided by the PF0100.
PF0100
Analog Integrated Circuit Device Data
34
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 28. Power Tree Summary
Supply
Output Voltage (V)
Step Size (mV)
Maximum Load Current (mA)
SW1A/B
SW1C
SW2
0.3 - 1.875
0.3 - 1.875
0.4 - 3.3
25
25
2500
2000
25/50
25/50
2000
SW3A/B
0.4 - 3.3
1250(40)
0.5*SW3A_OUT,
0.4 - 3.3
SW4
25/50
1000
SWBST
VGEN1
VGEN2
VGEN3
VGEN4
VGEN5
VGEN6
VSNVS
VREFDDR
5.00/5.05/5.10/5.15
0.80 – 1.55
0.80 – 1.55
1.8 – 3.3
50
50
600
100
250
100
350
100
200
0.4
50
100
100
100
100
NA
NA
1.8 – 3.3
1.8 – 3.3
1.8 – 3.3
1.0 - 3.0
0.5*SW3A_OUT
10
Notes
40. Current rating per independent phase, when SW3A/B is set in single or dual phase, current capability is up
to 2500 mA.
Figure 9 shows a simplified power map with various recommended options to supply the different block within the PF0100, as
well as the typical application voltage domain on the i.MX6X processor. Note that each application power tree is dependent upon
the system’s voltage and current requirements, therefore a proper input voltage should be selected for the regulators.
The minimum operating voltage for the main VIN supply is 2.8 V, for lower voltages proper operation is not guaranteed. However
at initial power up, the input voltage must surpass the rising UVDET threshold before proper operation is guaranteed. Refer to
the representative tables and text specifying each supply for information on performance metrics and operating ranges. Table 29
summarizes the UVDET thresholds.
Table 29. UVDET Threshold
UVDET Threshold
VIN
Rising
Falling
3.1 V
2.65 V
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
35
Functional Block Requirements and Behaviors
Power Generation
i.MX6X
MCU
SW1A
CORE
VDDARM_IN
(0.3 to 1.875 V), 1.25 A
SW1B
CORE
(0.3 to 1.875 V), 1.25 A
SW1C
SOC
(0.3 to 1.875 V), 2.0 A
VDDSOC_IN
VDDHIGH_IN
SW2
VDDHIGH
VIN
2.8 - 4.5 V
(0.4 to 3.3 V), 2.0 A
SW3A
DDR CORE
(0.4 to 3.3 V), 1.25 A
SW3B
DDR IO
VDD_DDR_IO
(0.4 to 3.3 V), 1.25 A
SW4
System/VTT
(0.4 to 3.3 V)
(0.5*VDDR)
1.0 A
SWBST
5.0 V, 0.6 A
LDO_3p0
VREFDDR
0.5*VDDR, 10 mA
SW3A/B
VIN
VSNVS
MUX /
VSNVS_IN
COIN
CHRG
1.0 to 3.0 V,
400 uA
Coincell
VGEN1
(0.80 to 1.55 V),
100 mA
USB_OTG
VIN
SW2
VINMAX = 3.4 V
VGEN2
(0.80 to 1.55 V),
250 mA
SW4
DDR3
VGEN3
(1.8 to 3.3 V),
100 mA
Peripherals
VIN
VINMAX = 3.6 V
SW2
VGEN4
(1.8 to 3.3 V),
350 mA
SW4
VGEN5
(1.8 to 3.3 V),
100 mA
VIN
VINMAX = 4.5 V
SW2
VGEN6
(1.8 to 3.3 V),
200 mA
SW4
Figure 9. PF0100 Typical Power Map
PF0100
Analog Integrated Circuit Device Data
36
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.4 Buck Regulators
Each buck regulator is capable of operating in PFM, APS, and PWM switching modes.
6.4.4.1
Current Limit
Each buck regulator has a programmable current limit. In an overcurrent condition, the current is limited cycle-by-cycle. If the
current limit condition persists for more than 8.0 ms, a fault interrupt is generated.
6.4.4.2
General Control
To improve system efficiency the buck regulators can operate in different switching modes. Changing between switching modes
can occur by any of the following means: I2C programming, exiting/entering the Standby mode, exiting/entering Sleep mode, and
load current variation. Available switching modes for buck regulators are presented in Table 30.
Table 30. Switching Mode Description
Mode
Description
OFF
The regulator is switched off and the output voltage is discharged.
In this mode, the regulator is always in PFM mode, which is useful at light loads for
optimized efficiency.
PFM
PWM
APS
In this mode, the regulator is always in PWM mode operation regardless of load conditions.
In this mode, the regulator moves automatically between pulse skipping mode and PWM
mode depending on load conditions.
During soft-start of the buck regulators, the controller transitions through the PFM, APS, and PWM switching modes. 3.0 ms
(typical) after the output voltage reaches regulation, the controller transitions to the selected switching mode. Depending on the
particular switching mode selected, additional ripple may be observed on the output voltage rail as the controller transitions
between switching modes.
Table 31 summarizes the Buck regulator programmability for Normal and Standby modes.
Table 31. Regulator Mode Control
SWxMODE[3:0]
Normal Mode
Standby Mode
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
Off
PWM
Off
Off
Reserved
PFM
Reserved
Off
APS
Off
PWM
PWM
PWM
APS
Reserved
APS
Reserved
APS
Reserved
Reserved
Reserved
APS
Reserved
Reserved
Reserved
PFM
PWM
PFM
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
37
Functional Block Requirements and Behaviors
Power Generation
Table 31. Regulator Mode Control
SWxMODE[3:0]
Normal Mode
Standby Mode
1110
1111
Reserved
Reserved
Reserved
Reserved
Transitioning between Normal and Standby modes can affect a change in switching modes as well as output voltage. The rate
of the output voltage change is controlled by the Dynamic Voltage Scaling (DVS), explained in Dynamic Voltage Scaling. For
each regulator, the output voltage options are the same for Normal and Standby modes.
When in Standby mode, the regulator outputs the voltage programmed in its standby voltage register and will operate in the mode
selected by the SWxMODE[3:0] bits. Upon exiting Standby mode, the regulator will return to its normal switching mode and its
output voltage programmed in its voltage register.
Any regulators whose SWxOMODE bit is set to “1” will enter Sleep mode if a PWRON turn-off event occurs, and any regulator
whose SWxOMODE bit is set to “0” will be turned off. In Sleep mode, the regulator outputs the voltage programmed in its off
(Sleep) voltage register and operates in the PFM mode. The regulator will exit the Sleep mode when a turn-on event occurs. Any
regulator whose SWxOMODE bit is set to “1” will remain on and change to its normal configuration settings when exiting the Sleep
state to the ON state. Any regulator whose SWxOMODE bit is set to “0” will be powered up with the same delay in the start-up
sequence as when powering On from Off. At this point, the regulator returns to its default ON state output voltage and switch
mode settings.
Table 25 shows the control bits in Sleep mode. When Sleep mode is activated by the SWxOMODE bit, the regulator will use the
set point as programmed by SW1xOFF[5:0] for SW1A/B/C and by SWxOFF[6:0] for SW2, SW3A/B, and SW4.
Dynamic Voltage Scaling
To reduce overall power consumption, processor core voltages can be varied depending on the mode or activity level of the
processor.
1. Normal operation: The output voltage is selected by I2C bits SW1x[5:0] for SW1A/B/C and SWx[6:0] for SW2, SW3A/B,
and SW4. A voltage transition initiated by I2C is governed by the DVS stepping rates shown in Table 34 and Table 35.
2. Standby Mode: The output voltage can be higher, or lower than in normal operation, but is typically selected to be the
lowest state retention voltage of a given processor; it is selected by I2C bits SW1xSTBY[5:0] for SW1A/B/C and by bits
SWxSTBY[6:0] for SW2, SW3A/B, and SW4. Voltage transitions initiated by a Standby event are governed by the
SW1xDVSSPEED[1:0] and SWxDVSSPEED[1:0] I2C bits shown in Table 34 and Table 35, respectively.
3. Sleep Mode: The output voltage can be higher or lower than in normal operation, but is typically selected to be the lowest
state retention voltage of a given processor; it is selected by I2C bits SW1xOFF[5:0] for SW1A/B/C and by bits
SWxOFF[6:0] for SW2, SW3A/B, and SW4. Voltage transitions initiated by a turn-off event are governed by the
SW1xDVSSPEED[1:0] and SWxDVSSPEED[1:0] I2C bits shown in Table 34 and Table 35, respectively.
Table 32, Table 33, Table 34, and Table 35 summarize the set point control and DVS time stepping applied to all regulators.
Table 32. DVS Control Logic for SW1A/B/C
STANDBY
Set Point Selected by
0
1
SW1x[5:0]
SW1xSTBY[5:0]
Table 33. DVS Control Logic for SW2, SW3A/B, and SW4
STANDBY
Set Point Selected by
0
1
SWx[6:0]
SWxSTBY[6:0]
PF0100
Analog Integrated Circuit Device Data
38
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 34. DVS Speed Selection for SW1A/B/C
SW1xDVSSPEED[1:0]
Function
00
01 (default)
10
25 mV step each 2.0 s
25 mV step each 4.0 s
25 mV step each 8.0 s
25 mV step each 16 s
11
Table 35. DVS Speed Selection for SW2, SW3A/B, and SW4
Function
SWx[6] = 0 or SWxSTBY[6] = 0
Function
SWx[6] = 1 or SWxSTBY[6] = 1
SWxDVSSPEED[1:0]
00
01 (default)
10
25 mV step each 2.0 s
25 mV step each 4.0 s
25 mV step each 8.0 s
25 mV step each 16 s
50 mV step each 4.0 s
50 mV step each 8.0 s
50 mV step each 16 s
50 mV step each 32 s
11
The regulators have a strong sourcing capability and sinking capability in PWM mode, therefore the fastest rising and falling
slopes are determined by the regulator in PWM mode. However, if the regulators are programmed in PFM or APS mode during
a DVS transition, the falling slope can be influenced by the load. Additionally, as the current capability in PFM mode is reduced,
controlled DVS transitions in PFM mode could be affected. Critically timed DVS transitions are best assured with PWM mode
operation.
The following diagram shows the general behavior for the regulators when initiated with I2C programming, or standby control.
During the DVS period the overcurrent condition on the regulator should be masked.
Requested
Set Point
Output Voltage
with light Load
Internally
Controlled Steps
Example
Output
Voltage
Actual Output
Voltage
Initial
Set Point
Actual
Output Voltage
Internally
Possible
Output Voltage
Window
Controlled Steps
Request for
Higher Voltage
Request for
Lower Voltage
Voltage
Change
Request
Initiated by I2C Programming, Standby Control
Figure 10. Voltage Stepping with DVS
Regulator Phase Clock
The SWxPHASE[1:0] bits select the phase of the regulator clock as shown in Table 36. By default, each regulator is initialized at
90 ° out of phase with respect to each other. For example, SW1x is set to 0 °, SW2 is set to 90 °, SW3A/B is set to 180 °, and
SW4 is set to 270 ° by default at power up.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
39
Functional Block Requirements and Behaviors
Power Generation
Table 36. Regulator Phase Clock Selection
Phase of Clock Sent to Regulator
SWxPHASE[1:0]
(degrees)
00
01
10
11
0
90
180
270
The SWxFREQ[1:0] register is used to set the desired switching frequency for each one of the buck regulators. Table 38 shows
the selectable options for SWxFREQ[1:0]. For each frequency, all phases will be available, this allows regulators operating at
different frequencies to have different relative switching phases. However, not all combinations are practical. For example,
2.0 MHz, 90 ° and 4.0 MHz, 180 ° are the same in terms of phasing. Table 37 shows the optimum phasing when using more than
one switching frequency.
Table 37. Optimum Phasing
Frequencies
Optimum Phasing
1.0 MHz
2.0 MHz
0 °
180 °
1.0 MHz
4.0 MHz
0 °
180 °
2.0 MHz
4.0 MHz
0 °
180 °
1.0 MHz
2.0 MHz
4.0 MHz
0 °
90 °
90 °
Table 38. Regulator Frequency Configuration
SWxFREQ[1:0]
Frequency
00
01
10
11
1.0 MHz
2.0 MHz
4.0 MHz
Reserved
Programmable Maximum Current
The maximum current, ISWxMAX, of each buck regulator is programmable. This allows the use of smaller inductors where lower
currents are required. Programmability is accomplished by choosing the number of paralleled power stages in each regulator.
The SWx_PWRSTG[2:0] bits on the Extended Page 2 of the register map control the number of power stages. See Table 39 for
the programmable options. Bit[0] must always be enabled to ensure the stage with the current sensor is chosen. The default
setting, SWx_PWRSTG[2:0] = 111, represents the highest maximum current. The current limit for each option is also scaled by
the percentage of power stages that are enabled.
PF0100
Analog Integrated Circuit Device Data
40
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 39. Programmable Current Configuration
% of Power Stages
Regulators
Control Bits
Rated Current (A)
Enabled
SW1AB_PWRSTG[2:0]
ISW1ABMAX
1.0
0
0
1
1
1
1
40%
80%
SW1AB
0
1
1
1
2.0
0
60%
1.5
1
100%
2.5
SW1C_PWRSTG[2:0]
ISW1CMAX
0.9
0
0
1
1
0
1
1
1
1
43%
58%
SW1C
1
1.2
0
86%
1.7
1
100%
2.0
SW2_PWRSTG[2:0]
ISW2MAX
0.75
0
0
1
1
0
1
1
1
1
38%
75%
SW2
1
1.5
0
63%
1.25
1
100%
2.0
SW3A_PWRSTG[2:0]
ISW3AMAX
0.5
0
0
1
1
0
1
1
1
1
40%
80%
SW3A
SW3B
SW4
1
1.0
0
60%
0.75
1
100%
1.25
SW3B_PWRSTG[2:0]
ISW3BMAX
0.5
0
0
1
1
0
1
1
1
1
40%
80%
1
1.0
0
60%
0.75
1
100%
1.25
SW4_PWRSTG[2:0]
ISW4MAX
0.5
0
0
1
1
0
1
0
1
1
1
1
1
50%
75%
0.75
75%
0.75
100%
1.0
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
41
Functional Block Requirements and Behaviors
Power Generation
6.4.4.3
SW1A/B/C
SW1/A/B/C are 2.5 to 4.5 A buck regulators that can be configured in various phasing schemes, depending on the desired cost/
performance trade-offs. The following configurations are available:
• SW1A/B/C single phase with one inductor
• SW1A/B as a single phase with one inductor and SW1C in independent mode with one inductor
• SW1A/B as a dual phase with two inductors and SW1C in independent mode with one inductor
The desired configuration is programmed by OTP by using SW1_CONFIG[1:0] bits in the register map Extended Page 1, as
shown in Table 40.
.
Table 40. SW1 Configuration
SW1_CONFIG[1:0]
Description
A/B/C Single Phase
00
A/B Single Phase
C Independent mode
01
A/B Dual Phase
C Independent mode
10
11
Reserved
PF0100
Analog Integrated Circuit Device Data
42
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
SW1A/B/C Single Phase
In this configuration, all phases A, B, and C, are connected together to a single inductor, thus, providing up to 4.50 A current
capability for high current applications. The feedback and all other controls are accomplished by use of pin SW1CFB and SW1C
control registers, respectively. Figure 11 shows the connection for SW1A/B/C in single phase mode.
During Single Phase mode operation, all three phases will use the same configuration for frequency, phase, and DVS speed set
in SW1CCONF register. However, the same configuration settings for frequency, phase, and DVS speed setting on SW1AB
registers should be used. The SW1FB pin should be left floating in this configuration.
VIN
SW1AIN
SW1ALX
SW1AMODE
ISENSE
CINSW1A
Controller
SW1A/B/C
Driver
LSW1
COSW1A
SW1AFAULT
Internal
I2C
Compensation
Z2
SW1FB
Z1
EA
VREF
DAC
VIN
SW1BIN
SW1BMODE
ISENSE
CINSW1B
Controller
I2C
Interface
SW1BLX
Driver
SW1BFAULT
SW1CMODE
VIN
SW1CIN
ISENSE
CINSW1C
Controller
SW1CLX
EP
Driver
SW1CFAULT
Internal
I2C
Compensation
Z2
SW1CFB
Z1
VREF
EA
DAC
Figure 11. SW1A/B/C Single Phase Block Diagram
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
43
Functional Block Requirements and Behaviors
Power Generation
SW1A/B Single Phase - SW1C Independent Mode
In this configuration, SW1A/B is connected as a single phase with a single inductor, while SW1C is used as an independent
output, using its own inductor and configurations parameters. This configuration allows reduced component count by using only
one inductor for SW1A/B. As mentioned before, SW1A/B and SW1C operate independently from one another, thus, they can be
operated with a different voltage set point for Normal, Standby, and Sleep modes, as well as switching mode selection and on/
off control. Figure 12 shows the physical connection for SW1A/B in single phase and SW1C as an independent output.
VIN
SW1AIN
SW1ALX
SW1AMODE
ISENSE
CINSW1A
Controller
SW1A/B
Driver
LSW1A
COSW1A
SW1AFAULT
Internal
I2C
Compensation
Z2
SW1FB
Z1
EA
VREF
DAC
VIN
SW1BIN
SW1BMODE
ISENSE
CINSW1B
Controller
I2C
Interface
SW1BLX
Driver
SW1BFAULT
SW1CMODE
VIN
SW1CIN
ISENSE
CINSW1C
Controller
SW1C
SW1CLX
EP
Driver
LSW1C
COSW1C
SW1CFAULT
Internal
I2C
Compensation
Z2
SW1CFB
Z1
VREF
EA
DAC
Figure 12. SW1A/B Single Phase, SW1C Independent Mode Block Diagram
Both SW1ALX and SW1BLX nodes operate at the same DVS, frequency, and phase configured by the SW1ABCONF register,
while SW1CLX node operates independently, using the configuration in the SW1CCONF register.
PF0100
Analog Integrated Circuit Device Data
44
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
SW1A/B Dual Phase - SW1C Independent Mode
In this mode, SW1A/B is connected in dual phase mode using one inductor per switching node, while SW1C is used as an
independent output using its own inductor and configuration parameters. This mode provides a smaller output voltage ripple on
the SW1A/B output. As mentioned before, SW1A/B and SW1C operate independently from one another, thus, they can be
operated with a different voltage set point for Normal, Standby, and Sleep modes, as well as switching mode selection and on/
off control. Figure 13 shows the physical connection for SW1A/B in dual phase and SW1C as an independent output.
VIN
SW1AIN
SW1ALX
SW1AMODE
ISENSE
CINSW1A
Controller
SW1AB
Driver
LSW1A
COSW1A
SW1AFAULT
Internal
I2C
Compensation
Z2
SW1FB
Z1
EA
VREF
DAC
VIN
SW1BIN
SW1BLX
SW1BMODE
ISENSE
CINSW1B
I2C
Interface
Controller
Driver
LSW1B
COSW1B
SW1BFAULT
SW1CMODE
VIN
SW1CIN
ISENSE
CINSW1C
Controller
SW1C
SW1CLX
EP
Driver
LSW1C
COSW1C
SW1CFAULT
Internal
I2C
Compensation
Z2
SW1CFB
Z1
VREF
EA
DAC
Figure 13. SW1A/B Dual Phase, SW1C Independent Mode Block Diagram
In this mode of operation, SW1ALX and SW1BLX nodes operate automatically at 180 ° phase shift from each other and use the
same frequency and DVS configured by SW1ABCONF register, while SW1CLX node operate independently using the
configuration in the SW1CCONF register.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
45
Functional Block Requirements and Behaviors
Power Generation
SW1A/B/C Setup and Control Registers
SW1A/B and SW1C output voltages are programmable from 0.300 to 1.875 V in steps of 25 mV. The output voltage set point is
independently programmed for Normal, Standby, and Sleep mode by setting the SW1x[5:0], SW1xSTBY[5:0], and
SW1xOFF[5:0] bits respectively. Table 41 shows the output voltage coding for SW1A/B or SW1C.
Note: Voltage set points of 0.6 V and below are not supported.
Table 41. SW1A/B/C Output Voltage Configuration
SW1x[5:0]
SW1x[5:0]
Set Point
SW1xSTBY[5:0]
SW1xOFF[5:0]
SW1x Output (V)
Set Point
SW1xSTBY[5:0]
SW1xOFF[5:0]
SW1x Output (V)
0
000000
000001
000010
000011
000100
000101
000110
000111
001000
001001
001010
001011
001100
001101
001110
001111
010000
010001
010010
010011
010100
010101
010110
010111
011000
011001
011010
011011
011100
011101
011110
011111
0.3000
0.3250
0.3500
0.3750
0.4000
0.4250
0.4500
0.4750
0.5000
0.5250
0.5500
0.5750
0.6000
0.6250
0.6500
0.6750
0.7000
0.7250
0.7500
0.7750
0.8000
0.8250
0.8500
0.8750
0.9000
0.9250
0.9500
0.9750
1.0000
1.0250
1.0500
1.0750
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
100000
100001
100010
100011
100100
100101
100110
100111
101000
101001
101010
101011
101100
101101
101110
101111
110000
110001
110010
110011
110100
110101
110110
110111
111000
111001
111010
111011
111100
111101
111110
111111
1.1000
1.1250
1.1500
1.1750
1.2000
1.2250
1.2500
1.2750
1.3000
1.3250
1.3500
1.3750
1.4000
1.4250
1.4500
1.4750
1.5000
1.5250
1.5500
1.5750
1.6000
1.6250
1.6500
1.6750
1.7000
1.7250
1.7500
1.7750
1.8000
1.8250
1.8500
1.8750
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
PF0100
Analog Integrated Circuit Device Data
46
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 42 provides a list of registers used to configure and operate SW1A/B/C and a detailed description on each one of these
register is provided in Table 43 through Table 52.
Table 42. SW1A/B/C Register Summary
Register
SW1ABVOLT
Address
Output
0x20
0x21
0x22
0x23
0x24
0x2E
0x2F
0x30
0x31
0x32
SW1AB Output voltage set point in normal operation
SW1AB Output voltage set point on Standby
SW1AB Output voltage set point on Sleep
SW1ABSTBY
SW1ABOFF
SW1ABMODE
SW1ABCONF
SW1CVOLT
SW1CSTBY
SW1COFF
SW1AB Switching Mode selector register
SW1AB DVS, Phase, Frequency and ILIM configuration
SW1C Output voltage set point in normal operation
SW1C Output voltage set point in Standby
SW1C Output voltage set point in Sleep
SW1CMODE
SW1CCONF
SW1C Switching Mode selector register
SW1C DVS, Phase, Frequency and ILIM configuration
Table 43. Register SW1ABVOLT - ADDR 0x20
Name
Bit #
R/W Default
Description
Sets the SW1AB output voltage during normal
operation mode. See Table 41 for all possible
configurations.
SW1AB
5:0
7:6
R/W
–
0x00
0x00
UNUSED
UNUSED
Table 44. Register SW1ABSTBY - ADDR 0x21
Name
Bit #
R/W Default
Description
Sets the SW1AB output voltage during Standby
mode. See Table 41 for all possible
configurations.
SW1ABSTBY
UNUSED
5:0
7:6
R/W
–
0x00
0x00
UNUSED
Table 45. Register SW1ABOFF - ADDR 0x22
Name
Bit #
R/W Default
Description
Sets the SW1AB output voltage during Sleep
mode. See Table 41 for all possible
configurations.
SW1ABOFF
5:0
7:6
R/W
–
0x00
0x00
UNUSED
UNUSED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
47
Functional Block Requirements and Behaviors
Power Generation
Table 46. Register SW1ABMODE - ADDR 0x23
Name
Bit #
R/W Default
Description
Sets the SW1AB switching operation mode.
See Table 31 for all possible configurations.
SW1ABMODE
UNUSED
3:0
4
R/W
–
0x80
0x00
UNUSED
Set status of SW1AB when in Sleep mode
SW1ABOMODE
UNUSED
5
R/W
–
0x00
0x00
0 = OFF
1 = PFM
7:6
UNUSED
Table 47. Register SW1ABCONF - ADDR 0x24
Name
Bit #
R/W Default
Description
SW1AB current limit level selection
0 = High level current limit
SW1ABILIM
0
R/W
0x00
1 = Low level current limit
UNUSED
1
R/W
R/W
0x00
0x00
Unused
SW1A/B switching frequency selector.
See Table 38.
SW1ABFREQ
3:2
SW1A/B Phase clock selection.
See Table 36.
SW1ABPHASE
5:4
7:6
R/W
R/W
0x00
0x00
SW1A/B DVS speed selection.
See Table 34.
SW1ABDVSSPEED
Table 48. Register SW1CVOLT - ADDR 0x2E
Name
Bit #
R/W Default
Description
Sets the SW1C output voltage during normal
operation mode. See Table 41 for all possible
configurations.
SW1C
5:0
7:6
R/W
–
0x00
0x00
UNUSED
UNUSED
Table 49. Register SW1CSTBY - ADDR 0x2F
Name
Bit #
R/W Default
Description
Sets the SW1C output voltage during Standby
mode. See Table 41 for all possible
configurations.
SW1CSTBY
5:0
7:6
R/W
–
0x00
0x00
UNUSED
UNUSED
Table 50. Register SW1COFF - ADDR 0x30
Name
Bit #
R/W Default
Description
Sets the SW1C output voltage during Sleep
mode. See Table 41 for all possible
configurations.
SW1COFF
5:0
7:6
R/W
–
0x00
0x00
UNUSED
UNUSED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
48
Functional Block Requirements and Behaviors
Power Generation
Table 51. Register SW1CMODE - ADDR 0x31
Name
Bit #
R/W Default
Description
Sets the SW1C switching operation mode.
See Table 30 for all possible configurations.
SW1CMODE
UNUSED
3:0
4
R/W
–
0x80
0x00
UNUSED
Set status of SW1C when in Sleep mode
SW1COMODE
UNUSED
5
R/W
–
0x00
0x00
0 = OFF
1 = PFM
7:6
UNUSED
Table 52. Register SW1CCONF - ADDR 0x32
Name
Bit #
R/W Default
Description
SW1C current limit level selection
0 = High level current limit
1 = Low level current limit
SW1CILIM
0
R/W
0x00
UNUSED
1
R/W
R/W
0x00
0x00
Unused
SW1C switching frequency selector.
See Table 38.
SW1CFREQ
3:2
SW1C Phase clock selection.
See Table 36.
SW1CPHASE
5:4
7:6
R/W
R/W
0x00
0x00
SW1C DVS speed selection.
See Table 34.
SW1CDVSSPEED
SW1A/B/C External Components
Table 53. SW1A/B/C External Component Recommendations
Mode
A/B/C Single
A/B Single - C
Independent Mode Independent Mode
A/B Dual - C
Components
Description
Phase
(41)
CINSW1A
SW1A Input capacitor
4.7 F
0.1 F
4.7 F
0.1 F
4.7 F
0.1 F
6 x 22 F
–
4.7 F
0.1 F
4.7 F
0.1 F
(41)
CIN1AHF
SW1A Decoupling input capacitor
SW1B Input capacitor
(41)
CINSW1B
4.7 F
4.7 F
(41)
CIN1BHF
SW1B Decoupling input capacitor
SW1C Input capacitor
0.1 F
0.1 F
(41)
CINSW1C
4.7 F
4.7 F
(41)
CIN1CHF
SW1C Decoupling input capacitor
SW1A/B Output capacitor
SW1C Output capacitor
0.1 F
0.1 F
(41)
COSW1AB
4 x 22 F
2 x 22 F
4 x 22 F
2 x 22 F
(41)
COSW1C
1.0 H
1.0 H
1.0 H
LSW1A
SW1A Inductor
SW1B Inductor
DCR = 12 m
DCR = 12 m
DCR = 60 m
I
SAT = 6.0 A
I
SAT = 4.5 A
I
SAT = 2.4 A
1.0 H
LSW1B
–
–
DCR = 60 m
SAT = 2.4 A
I
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
49
Functional Block Requirements and Behaviors
Power Generation
Table 53. SW1A/B/C External Component Recommendations
Mode
A/B/C Single
A/B Single - C
Independent Mode Independent Mode
A/B Dual - C
Components
Description
Phase
1.0 H
1.0 H
LSW1C
Notes
SW1C Inductor
–
DCR = 60 m
DCR = 60 m
ISAT = 2.4 A
I
SAT = 2.4 A
41. Use X5R or X7R capacitors.
SW1A/B/C Specifications
Table 54. SW1A/B/C Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA,
SW1x_PWRSTG[2:0] = [111], typical external component values, fSW1x = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA, SW1x_PWRSTG[2:0] = [111], and 25 °C, unless
otherwise noted.
Parameter
SW1A/B/C (SINGLE PHASE)
Symbol
Min
Typ
Max
Unit
VINSW1A
VINSW1B
VINSW1C
Operating Input Voltage
2.8
–
–
4.5
–
V
V
Nominal Output Voltage
Output Voltage Accuracy
VSW1ABC
Table 41
•
PWM, APS, 2.8 V < VIN < 4.5 V, 0 < ISW1ABC < 4.5 A
0.625 V VSW1ABC 1.450 V
1.475 V VSW1ABC 1.875 V
-25
-3.0%
–
–
25
3.0%
mV
%
VSW1ABCACC
•
PFM, steady state, 2.8 V < VIN < 4.5 V, 0 < ISW1ABC < 150 mA
-65
-45
-3.0%
–
–
–
65
45
3.0%
0.625 V < VSW1ABC < 0.675 V
0.7 V < VSW1ABC < 0.85 V
0.875 V < VSW1ABC < 1.875 V
Rated Output Load Current,
ISW1ABC
–
–
4500
mA
A
2.8 V < VIN < 4.5 V, 0.625 V < VSW1ABC < 1.875 V
Current Limiter Peak Current Detection
•
Current through Inductor
SW1ABILIM = 0
ISW1ABCLIM
7.1
5.3
10.5
7.9
13.7
10.3
SW1ABILIM = 1
Start-up Overshoot
ISW1ABC = 0 mA
DVS clk = 25 mV/4 s, VIN = VINSW1x = 4.5 V, VSW1ABC = 1.875 V
VSW1ABCOSH
–
–
66
mV
µs
Turn-on Time
Enable to 90% of end value
ISW1x = 0 mA
tONSW1ABC
–
–
500
DVS clk = 25 mV/4.0 s, VIN = VINSW1x = 4.5 V,
V
SW1ABC = 1.875 V
Switching Frequency
SW1xFREQ[1:0] = 00
SW1xFREQ[1:0] = 01
SW1xFREQ[1:0] = 10
–
–
–
1.0
2.0
4.0
–
–
–
fSW1ABC
MHz
PF0100
Analog Integrated Circuit Device Data
50
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 54. SW1A/B/C Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA,
SW1x_PWRSTG[2:0] = [111], typical external component values, fSW1x = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA, SW1x_PWRSTG[2:0] = [111], and 25 °C, unless
otherwise noted.
Parameter
SW1A/B/C (SINGLE PHASE) (CONTINUED)
Efficiency
Symbol
Min
Typ
Max
Unit
•
VIN = 3.6 V, fSW1ABC = 2.0 MHz, LSW1ABC = 1.0 H
–
–
–
–
–
–
77
82
86
84
80
68
–
–
–
–
–
–
PFM, 0.9 V, 1.0 mA
PFM, 1.2 V, 50 mA
APS, PWM, 1.2 V, 850 mA
APS, PWM, 1.2 V, 1275 mA
APS, PWM, 1.2 V, 2125 mA
APS, PWM, 1.2 V, 4500 mA
SW1ABC
%
Output Ripple
VSW1ABC
VSW1ABCLIR
VSW1ABCLOR
–
–
–
10
–
–
mV
mV
mV
Line Regulation (APS, PWM)
DC Load Regulation (APS, PWM)
Transient Load Regulation
20
20
–
•
Transient load = 0 to 2.25 A, di/dt = 100 mA/s
Overshoot
Undershoot
VSW1ABCLOTR
mV
–
–
–
–
50
50
Quiescent Current
PFM Mode
ISW1ABCQ
–
–
18
145
–
–
µA
APS Mode
Discharge Resistance
RSW1ABCDIS
–
600
–
SW1A/B (SINGLE/DUAL PHASE)
VINSW1A
VINSW1B
Operating Input Voltage
2.8
–
–
4.5
–
V
V
Nominal Output Voltage
Output Voltage Accuracy
VSW1AB
Table 41
•
PWM, APS, 2.8 V < VIN < 4.5 V, 0 < ISW1AB < 2.5 A
0.625 V VSW1AB 1.450 V
1.475 V VSW1AB 1.875 V
-25
-3.0%
-
-
25
3.0%
mV
%
VSW1ABACC
•
PFM, steady state, 2.8 V < VIN < 4.5 V, 0 < ISW1AB < 150 mA
-65
-45
-3.0%
–
–
–
65
45
3.0%
0.625 V < VSW1AB < 0.675 V
0.7 V < VSW1AB < 0.85 V
0.875 V < VSW1AB < 1.875 V
Rated Output Load Current, (43)
ISW1AB
–
–
2500
mA
2.8 V < VIN < 4.5 V, 0.625 V < VSW1AB < 1.875 V
Current Limiter Peak Current Detection (43)
•
SW1A/B Single Phase (current through inductor)
SW1ABILIM = 0
4.5
3.3
6.5
4.9
8.5
6.4
SW1ABILIM = 1
ISW1ABLIM
A
•
SW1A/B Dual Phase (current through inductor per phase)
SW1ABILIM = 0
SW1ABILIM = 1
2.2
1.6
3.2
2.4
4.3
3.2
Start-up Overshoot
ISW1AB = 0.0 mA
VSW1ABOSH
–
–
66
mV
DVS clk = 25 mV/4 s, VIN = VINSW1x = 4.5 V, VSW1AB = 1.875 V
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
51
Functional Block Requirements and Behaviors
Power Generation
Table 54. SW1A/B/C Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA,
SW1x_PWRSTG[2:0] = [111], typical external component values, fSW1x = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA, SW1x_PWRSTG[2:0] = [111], and 25 °C, unless
otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
SW1A/B (SINGLE/DUAL PHASE) (CONTINUED)
Turn-on Time
Enable to 90% of end value
tONSW1AB
–
–
500
µs
I
SW1AB = 0.0 mA
DVS clk = 25 mV/4 s, VIN = VINSW1x = 4.5 V, VSW1AB = 1.875 V
Switching Frequency
SW1ABFREQ[1:0] = 00
SW1ABFREQ[1:0] = 01
SW1ABFREQ[1:0] = 10
–
–
–
1.0
2.0
4.0
–
–
–
fSW1AB
MHz
Efficiency (Single Phase)
•
VIN = 3.6 V, fSW1AB = 2.0 MHz, LSW1AB = 1.0 H
–
–
–
–
–
–
82
84
86
87
82
71
–
–
–
–
–
–
PFM, 0.9 V, 1.0 mA
PFM, 1.2 V, 50 mA
APS, PWM, 1.2 V, 500 mA
APS, PWM, 1.2 V, 750 mA
APS, PWM, 1.2 V, 1250 mA
APS, PWM, 1.2 V, 2500 mA
SW1AB
%
Output Ripple
VSW1AB
VSW1ABLIR
VSW1ABLOR
–
–
–
10
–
–
mV
mV
mV
Line Regulation (APS, PWM)
DC Load Regulation (APS, PWM)
Transient Load Regulation
20
20
–
•
Transient load = 0 to 1.25 A, di/dt = 100 mA/s
Overshoot
Undershoot
VSW1ABLOTR
mV
µA
–
–
–
–
50
50
Quiescent Current
PFM Mode
ISW1ABQ
–
–
18
235
–
–
APS Mode
SW1A P-MOSFET RDSON
VINSW1A = 3.3 V
RONSW1AP
RONSW1AN
ISW1APQ
–
–
–
–
–
–
–
215
258
–
245
326
7.5
m
m
µA
SW1A N-MOSFET RDSON
VINSW1A = 3.3 V
SW1A P-MOSFET Leakage Current
VINSW1A = 4.5 V
SW1A N-MOSFET Leakage Current
VINSW1A = 4.5 V
ISW1ANQ
–
2.5
µA
SW1B P-MOSFET RDSON
VINSW1B = 3.3 V
RONSW1BP
RONSW1BN
ISW1BPQ
215
258
–
245
326
7.5
m
m
µA
SW1B N-MOSFET RDSON
VINSW1B = 3.3 V
SW1B P-MOSFET Leakage Current
VINSW1B = 4.5 V
SW1B N-MOSFET Leakage Current
VINSW1B = 4.5 V
ISW1BNQ
–
–
–
2.5
–
µA
Discharge Resistance
RSW1ABDIS
600
PF0100
Analog Integrated Circuit Device Data
52
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 54. SW1A/B/C Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA,
SW1x_PWRSTG[2:0] = [111], typical external component values, fSW1x = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA, SW1x_PWRSTG[2:0] = [111], and 25 °C, unless
otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
SW1C (INDEPENDENT)
Operating Input Voltage
Nominal Output Voltage
Output Voltage Accuracy
VINSW1C
VSW1C
2.8
–
–
4.5
–
V
V
Table 41
•
PWM, APS, 2.8 V < VIN < 4.5 V, 0 < ISW1C < 2.0 A
0.625 V VSW1C 1.450 V
1.475 V VSW1C 1.875 V
-25
-3.0%
–
–
25
3.0%
VSW1CACC
mV
•
PFM, steady state 2.8 V < VIN < 4.5 V, 0 < ISW1C < 50 mA
-65
-45
-3.0%
–
–
–
65
45
3.0%
0.625 V < VSW1C < 0.675 V
0.7 V < VSW1C < 0.85 V
0.875 V < VSW1C < 1.875 V
Rated Output Load Current
ISW1C
–
–
2000
mA
A
2.8 V < VIN < 4.5 V, 0.625 V < VSW1C < 1.875 V
Current Limiter Peak Current Detection
•
Current through Inductor
SW1CILIM = 0
ISW1CLIM
2.6(42)
1.95
4.0
3.0
5.2
3.9
SW1CILIM = 1
Start-up Overshoot
I
SW1C = 0 mA
VSW1COSH
–
–
–
–
66
mV
µs
DVS clk = 25 mV/4 s, VIN = VINSW1C = 4.5 V, VSW1C = 1.875 V
Turn-on Time
Enable to 90% of end value
SW1C = 0 mA
tONSW1C
500
I
DVS clk = 25 mV/4 s, VIN = VINSW1C = 4.5 V, VSW1C = 1.875 V
Switching Frequency
SW1CFREQ[1:0] = 00
SW1CFREQ[1:0] = 01
SW1CFREQ[1:0] = 10
–
–
–
1.0
2.0
4.0
–
–
–
fSW1C
MHz
Efficiency
•
VIN = 3.6 V, fSW1C = 2.0 MHz, LSW1C = 1.0 H
–
–
–
–
–
–
77
78
86
84
78
65
–
–
–
–
–
–
PFM, 0.9 V, 1.0 mA
PFM, 1.2 V, 50 mA
APS, PWM, 1.2 V, 400 mA
APS, PWM, 1.2 V, 600 mA
APS, PWM, 1.2 V, 1000 mA
APS, PWM, 1.2 V, 2000 mA
SW1C
%
Output Ripple
VSW1C
VSW1CLIR
VSW1CLOR
–
–
–
10
–
–
mV
mV
mV
Line Regulation (APS, PWM)
DC Load Regulation (APS, PWM)
Transient Load Regulation
20
20
–
•
Transient load = 0.0 mA to 1.0 A, di/dt = 100 mA/s
Overshoot
Undershoot
VSW1CLOTR
mV
µA
–
–
–
–
50
50
Quiescent Current
PFM Mode
ISW1CQ
–
–
22
145
–
–
APS Mode
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
53
Functional Block Requirements and Behaviors
Power Generation
Table 54. SW1A/B/C Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA,
SW1x_PWRSTG[2:0] = [111], typical external component values, fSW1x = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW1x = 3.6 V, VSW1x = 1.2 V, ISW1x = 100 mA, SW1x_PWRSTG[2:0] = [111], and 25 °C, unless
otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
SW1C (INDEPENDENT) (CONTINUED)
SW1C P-MOSFET RDSON
at VINSW1C = 3.3 V
RONSW1CP
RONSW1CN
ISW1CPQ
–
–
–
m
m
µA
184
206
SW1C N-MOSFET RDSON
at VINSW1C = 3.3 V
211
–
260
SW1C P-MOSFET Leakage Current
VINSW1C = 4.5 V
10.5
SW1C N-MOSFET Leakage Current
VINSW1C = 4.5 V
ISW1CNQ
–
–
–
3.5
–
µA
Discharge Resistance
RSW1CDIS
600
Notes
42. Meets 1.89 A current rating for VDDSOC_IN domain on i.MX6X processor.
43. Current rating of SW1AB supports the Power Virus mode of operation of the i.MX6X processor.
PF0100
Analog Integrated Circuit Device Data
54
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Figure 14. SW1AB Efficiency Waveforms: VIN = 4.2 V; VOUT = 1.375 V; Consumer Version
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
55
Functional Block Requirements and Behaviors
Power Generation
Figure 15. SW1AB Efficiency Waveforms: VIN = 4.2 V; VOUT = 1.375 V; Extended Industrial Version
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
56
Functional Block Requirements and Behaviors
Power Generation
Figure 16. SW1C Efficiency Waveforms: VIN = 4.2 V; VOUT = 1.375 V; Consumer Version
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
57
Functional Block Requirements and Behaviors
Power Generation
Figure 17. SW1C Efficiency Waveforms: VIN = 4.2 V; VOUT = 1.375 V; Extended Industrial Version
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
58
Functional Block Requirements and Behaviors
Power Generation
6.4.4.4
SW2
SW2 is a single phase, 2.0 A rated buck regulator. Table 30 describes the modes, and Table 31 show the options for the
SWxMODE[3:0] bits.
Figure 18 shows the block diagram and the external component connections for SW2 regulator.
VIN
SW2IN
SW2MODE
ISENSE
CINSW2
Controller
SW2
SW2LX
EP
Driver
LSW2
COSW2
SW2FAULT
I2C
Interface
Internal
I2C
Compensation
Z2
SW2FB
Z1
VREF
EA
DAC
Figure 18. SW2 Block Diagram
SW2 Setup and Control Registers
SW2 output voltage is programmable from 0.400 to 3.300 V; however, bit SW2[6] in register SW2VOLT is read-only during
normal operation. Its value is determined by the default configuration, or may be changed by using the OTP registers. Therefore,
once SW2[6] is set to “0”, the output will be limited to the lower output voltages from 0.400 to 1.975 V with 25 mV increments, as
determined by bits SW2[5:0]. Likewise, once bit SW2[6] is set to “1”, the output voltage will be limited to the higher output voltage
range from 0.800 to 3.300 V with 50 mV increments, as determined by bits SW2[5:0].
In order to optimize the performance of the regulator, it is recommended that only voltages from 2.000 to 3.300 V be used in the
high range, and the lower range be used for voltages from 0.400 to 1.975 V.
The output voltage set point is independently programmed for Normal, Standby, and Sleep mode by setting the SW2[5:0],
SW2STBY[5:0] and SW2OFF[5:0] bits, respectively. However, the initial state of bit SW2[6] will be copied into bits SW2STBY[6],
and SW2OFF[6] bits. Therefore, the output voltage range will remain the same in all three operating modes. Table 55 shows the
output voltage coding valid for SW2.
Note: Voltage set points of 0.6 V and below are not supported.
Table 55. SW2 Output Voltage Configuration
Low Output Voltage Range(44)
High Output Voltage Range
Set Point
SW2[6:0]
SW2 Output
Set Point
SW2[6:0]
SW2 Output
0
1
0000000
0000001
0000010
0000011
0000100
0000101
0000110
0000111
0001000
0001001
0001010
0.4000
0.4250
0.4500
0.4750
0.5000
0.5250
0.5500
0.5750
0.6000
0.6250
0.6500
64
65
66
67
68
69
70
71
72
73
74
1000000
1000001
1000010
1000011
1000100
1000101
1000110
1000111
1001000
1001001
1001010
0.8000
0.8500
0.9000
0.9500
1.0000
1.0500
1.1000
1.1500
1.2000
1.2500
1.3000
2
3
4
5
6
7
8
9
10
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
59
Functional Block Requirements and Behaviors
Power Generation
Table 55. SW2 Output Voltage Configuration (continued)
Low Output Voltage Range(44)
High Output Voltage Range
Set Point
SW2[6:0]
SW2 Output
Set Point
SW2[6:0]
SW2 Output
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
0001011
0001100
0001101
0001110
0001111
0010000
0010001
0010010
0010011
0010100
0010101
0010110
0010111
0011000
0011001
0011010
0011011
0011100
0011101
0011110
0011111
0100000
0100001
0100010
0100011
0100100
0100101
0100110
0100111
0101000
0101001
0101010
0101011
0101100
0101101
0101110
0101111
0.6750
0.7000
0.7250
0.7500
0.7750
0.8000
0.8250
0.8500
0.8750
0.9000
0.9250
0.9500
0.9750
1.0000
1.0250
1.0500
1.0750
1.1000
1.1250
1.1500
1.1750
1.2000
1.2250
1.2500
1.2750
1.3000
1.3250
1.3500
1.3750
1.4000
1.4250
1.4500
1.4750
1.5000
1.5250
1.5500
1.5750
75
76
1001011
1001100
1001101
1001110
1001111
1010000
1010001
1010010
1010011
1010100
1010101
1010110
1010111
1011000
1011001
1011010
1011011
1011100
1011101
1011110
1011111
1100000
1100001
1100010
1100011
1100100
1100101
1100110
1100111
1101000
1101001
1101010
1101011
1101100
1101101
1101110
1101111
1.3500
1.4000
1.4500
1.5000
1.5500
1.6000
1.6500
1.7000
1.7500
1.8000
1.8500
1.9000
1.9500
2.0000
2.0500
2.1000
2.1500
2.2000
2.2500
2.3000
2.3500
2.4000
2.4500
2.5000
2.5500
2.6000
2.6500
2.7000
2.7500
2.8000
2.8500
2.9000
2.9500
3.0000
3.0500
3.1000
3.1500
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
PF0100
Analog Integrated Circuit Device Data
60
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 55. SW2 Output Voltage Configuration (continued)
Low Output Voltage Range(44)
High Output Voltage Range
Set Point
SW2[6:0]
SW2 Output
Set Point
SW2[6:0]
SW2 Output
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
0110000
0110001
0110010
0110011
0110100
0110101
0110110
0110111
0111000
0111001
0111010
0111011
0111100
0111101
0111110
0111111
1.6000
1.6250
1.6500
1.6750
1.7000
1.7250
1.7500
1.7750
1.8000
1.8250
1.8500
1.8750
1.9000
1.9250
1.9500
1.9750
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
1110000
1110001
1110010
1110011
1110100
1110101
1110110
1110111
1111000
1111001
1111010
1111011
1111100
1111101
1111110
1111111
3.2000
3.2500
3.3000
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Notes
44. For voltages less than 2.0 V, only use set points 0 to 63.
Setup and control of SW2 is done through I2C registers listed in Table 56, and a detailed description of each one of the registers
is provided in Tables 57 to Table 61.
Table 56. SW2 Register Summary
Register
SW2VOLT
Address
Description
0x35
0x36
0x37
0x38
0x39
Output voltage set point on normal operation
Output voltage set point on Standby
Output voltage set point on Sleep
SW2STBY
SW2OFF
SW2MODE
SW2CONF
Switching Mode selector register
DVS, Phase, Frequency, and ILIM configuration
Table 57. Register SW2VOLT - ADDR 0x35
Name
Bit #
R/W Default
Description
Sets the SW2 output voltage during normal operation
mode. See Table 55 for all possible configurations.
SW2
SW2
5:0
R/W
0x00
Sets the operating output voltage range for SW2. Set
during OTP or TBB configuration only. See Table 55
for all possible configurations.
6
7
R
–
0x00
0x00
UNUSED
UNUSED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
61
Functional Block Requirements and Behaviors
Power Generation
Table 58. Register SW2STBY - ADDR 0x36
Name
SW2STBY
Bit #
R/W Default
Description
Sets the SW2 output voltage during Standby mode.
See Table 55 for all possible configurations.
5:0
R/W
0x00
Sets the operating output voltage range for SW2 on
Standby mode. This bit inherits the value configured
on bit SW2[6] during OTP or TBB configuration. See
Table 55 for all possible configurations.
SW2STBY
UNUSED
6
7
R
–
0x00
0x00
UNUSED
Table 59. Register SW2OFF - ADDR 0x37
Name
SW2OFF
Bit #
R/W Default
Description
Sets the SW2 output voltage during Sleep mode. See
Table 55 for all possible configurations.
5:0
R/W
0x00
Sets the operating output voltage range for SW2 on
Sleep mode. This bit inherits the value configured on
bit SW2[6] during OTP or TBB configuration. See
Table 55 for all possible configurations.
SW2OFF
UNUSED
6
7
R
–
0x00
0x00
UNUSED
Table 60. Register SW2MODE - ADDR 0x38
Name
SW2MODE
Bit #
R/W Default
Description
Sets the SW2 switching operation mode.
See Table 30 for all possible configurations.
3:0
4
R/W
–
0x80
0x00
UNUSED
UNUSED
Set status of SW2 when in Sleep mode
SW2OMODE
UNUSED
5
R/W
–
0x00
0x00
0 = OFF
1 = PFM
7:6
UNUSED
Table 61. Register SW2CONF - ADDR 0x39
Name
Bit #
R/W Default
Description
SW2 current limit level selection
0 = High level current limit
1 = Low level current limit
SW2ILIM
0
R/W
0x00
UNUSED
1
R/W
R/W
0x00
0x00
Unused
SW2 switching frequency selector.
See Table 38.
SW2FREQ
3:2
SW2 Phase clock selection.
See Table 36.
SW2PHASE
5:4
7:6
R/W
R/W
0x00
0x00
SW2 DVS speed selection.
See Table 35.
SW2DVSSPEED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
62
Functional Block Requirements and Behaviors
Power Generation
SW2 External Components
Table 62. SW2 External Component Recommendations
Components
Description
SW2 Input capacitor
Values
(45)
CINSW2
4.7 F
0.1 F
(45)
CIN2HF
COSW2
SW2 Decoupling input capacitor
SW2 Output capacitor
(45)
2 x 22 F
1.0 H
LSW2
SW2 Inductor
DCR = 50 m
I
SAT = 2.65 A
Notes
45. Use X5R or X7R capacitors.
SW2 Specifications
Table 63. SW2 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW2 = 3.6 V, VSW2 = 3.15 V, ISW2 = 100 mA,
SW2_PWRSTG[2:0] = [111], typical external component values, fSW2 = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW2 = 3.6 V, VSW2 = 3.15 V, ISW2 = 100 mA, SW2_PWRSTG[2:0] = [111], and 25 °C, unless otherwise
noted.
Parameter
SWITCH MODE SUPPLY SW2
Symbol
Min
Typ
Max
Unit
Operating Input Voltage(46)
Nominal Output Voltage
Output Voltage Accuracy
VINSW2
VSW2
2.8
–
–
4.5
–
V
V
Table 55
•
PWM, APS, 2.8 V < VIN < 4.5 V, 0 < ISW2 < 2.0 A
0.625 V < VSW2 < 0.85 V
0.875 V < VSW2 < 1.975 V
2.0 V < VSW2 < 3.3 V
-25
-3.0%
-6.0%
–
–
–
25
3.0%
6.0%
mV
%
VSW2ACC
•
PFM, 2.8 V < VIN < 4.5 V, 0 < ISW2 50 mA
-65
-45
-3.0%
-3.0%
–
–
–
–
65
45
3.0%
3.0%
0.625 V < VSW2 < 0.675 V
0.7 V < VSW2 < 0.85 V
0.875 V < VSW2 < 1.975 V
2.0 V < VSW2 < 3.3 V
Rated Output Load Current (47)
ISW2
–
–
2000
mA
A
2.8 V < VIN < 4.5 V, 0.625 V < VSW2 < 3.3 V
Current Limiter Peak Current Detection
•
Current through Inductor
SW2ILIM = 0
SW2ILIM = 1
ISW2LIM
2.8
2.1
4.0
3.0
5.2
3.9
Start-up Overshoot
I
SW2 = 0.0 mA
VSW2OSH
–
–
–
–
66
mV
µs
DVS clk = 25 mV/4 s, VIN = VINSW2 = 4.5 V
Turn-on Time
Enable to 90% of end value
SW2 = 0.0 mA
tONSW2
550
I
DVS clk = 50 mV/8 s, VIN = VINSW2 = 4.5 V
Switching Frequency
SW2FREQ[1:0] = 00
SW2FREQ[1:0] = 01
SW2FREQ[1:0] = 10
–
–
–
1.0
2.0
4.0
–
–
–
fSW2
MHz
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
63
Functional Block Requirements and Behaviors
Power Generation
Table 63. SW2 Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW2 = 3.6 V, VSW2 = 3.15 V, ISW2 = 100 mA,
SW2_PWRSTG[2:0] = [111], typical external component values, fSW2 = 2.0 MHz, unless otherwise noted. Typical values are
characterized at VIN = VINSW2 = 3.6 V, VSW2 = 3.15 V, ISW2 = 100 mA, SW2_PWRSTG[2:0] = [111], and 25 °C, unless otherwise
noted.
Parameter
SWITCH MODE SUPPLY SW2 (CONTINUED)
Efficiency
Symbol
Min
Typ
Max
Unit
•
VIN = 3.6 V, fSW2 = 2.0 MHz, LSW2 = 1.0 H
–
–
–
–
–
–
94
95
96
94
92
86
–
–
–
–
–
–
PFM, 3.15 V, 1.0 mA
PFM, 3.15 V, 50 mA
APS, PWM, 3.15 V, 400 mA
APS, PWM, 3.15 V, 600 mA
APS, PWM, 3.15 V, 1000 mA
APS, PWM, 3.15 V, 2000 mA
SW2
%
Output Ripple
VSW2
VSW2LIR
VSW2LOR
–
–
–
10
–
–
mV
mV
mV
Line Regulation (APS, PWM)
DC Load Regulation (APS, PWM)
Transient Load Regulation
20
20
–
•
Transient load = 0.0 mA to 1.0 A, di/dt = 100 mA/s
Overshoot
Undershoot
VSW2LOTR
mV
µA
–
–
–
–
50
50
Quiescent Current
PFM Mode
APS Mode (Low output voltage settings)
APS Mode (High output voltage settings)
–
–
–
23
145
305
–
–
–
ISW2Q
SW2 P-MOSFET RDSON
at VIN = VINSW2 = 3.3 V
RONSW2P
RONSW2N
ISW2PQ
–
–
–
190
212
–
209
255
12
m
m
µA
SW2 N-MOSFET RDSON
at VIN = VINSW2 = 3.3 V
SW2 P-MOSFET Leakage Current
VIN = VINSW2 = 4.5 V
SW2 N-MOSFET Leakage Current
ISW2NQ
–
–
–
4.0
–
µA
V
IN = VINSW2 = 4.5 V
Discharge Resistance
RSW2DIS
600
Notes
46. When output is set to > 2.6 V the output will follow the input down when VIN gets near 2.8 V.
47. The higher output voltages available depend on the voltage drop in the conduction path as given by the following equation:
(VINSW2 - VSW2) = ISW2* (DCR of Inductor +RONSW2P + PCB trace resistance).
PF0100
Analog Integrated Circuit Device Data
64
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Figure 19. SW2 Efficiency Waveforms: VIN = 4.2 V; VOUT = 3.0 V; Consumer Version
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
65
Functional Block Requirements and Behaviors
Power Generation
Figure 20. SW2 Efficiency Waveforms: VIN = 4.2 V; VOUT = 3.0 V; Extended Industrial Version
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
66
Functional Block Requirements and Behaviors
Power Generation
6.4.4.5
SW3A/B
SW3A/B are 1.25 to 2.5 A rated buck regulators, depending on the configuration. Table 30 describes the available switching
modes and Table 31 show the actual configuration options for the SW3xMODE[3:0] bits.
SW3A/B can be configured in various phasing schemes, depending on the desired cost/performance trade-offs. The following
configurations are available:
• A single phase
• A dual phase
• Independent regulators
The desired configuration is programmed in OTP by using the SW3_CONFIG[1:0] bits.Table 64 shows the options for the
SW3CFG[1:0] bits.
Table 64. SW3 Configuration
SW3_CONFIG[1:0]
Description
00
01
10
11
A/B Single Phase
A/B Single Phase
A/B Dual Phase
A/B Independent
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
67
Functional Block Requirements and Behaviors
Power Generation
SW3A/B Single Phase
In this configuration, SW3ALX and SW3BLX are connected in single phase with a single inductor a shown in Figure 21. This
configuration reduces cost and component count. Feedback is taken from the SW3AFB pin and the SW3BFB pin must be left
open. Although control is from SW3A, registers of both regulators, SW3A and SW3B, must be identically set.
VIN
SW3AIN
SW3ALX
SW3AMODE
ISENSE
CINSW3A
Controller
SW3
Driver
LSW3A
COSW3A
SW3AFAULT
Internal
I2C
Compensation
Z2
SW3AFB
SW3BIN
I2C
Interface
Z1
VREF
EA
DAC
VIN
SW3BMODE
ISENSE
CINSW3B
Controller
SW3BLX
Driver
SW3BFAULT
EP
I2C
Internal
Compensation
Z2
VREF
SW3BFB
Z1
DAC
EA
Figure 21. SW3A/B Single Phase Block Diagram
PF0100
Analog Integrated Circuit Device Data
68
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
SW3A/B Dual Phase
SW3A/B can be connected in dual phase configuration using one inductor per switching node, as shown in Figure 22. This mode
allows a smaller output voltage ripple. Feedback is taken from pin SW3AFB and pin SW3BFB must be left open. Although control
is from SW3A, registers of both regulators, SW3A and SW3B, must be identically set. In this configuration, the regulators switch
180 degrees apart.
VIN
SW3AIN
SW3ALX
SW3AMODE
ISENSE
CINSW3A
Controller
SW3
Driver
LSW3A
COSW3A
SW3AFAULT
Internal
I2C
Compensation
Z2
I2C
Interface
SW3AFB
SW3BIN
Z1
VREF
EA
DAC
VIN
SW3BMODE
ISENSE
CINSW3B
Controller
SW3BLX
EP
Driver
LSW3B
COSW3B
SW3BFAULT
I2C
Internal
Compensation
Z2
VREF
SW3BFB
Z1
DAC
EA
Figure 22. SW3A/B Dual Phase Block Diagram
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
69
Functional Block Requirements and Behaviors
Power Generation
SW3A - SW3B Independent Outputs
SW3A and SW3B can be configured as independent outputs as shown in Figure 23, providing flexibility for applications requiring
more voltage rails with less current capability. Each output is configured and controlled independently by its respective I2C
registers as shown in Table 66.
VIN
SW3AIN
SW3ALX
SW3AMODE
ISENSE
CINSW3A
Controller
SW3A
Driver
LSW3A
COSW3A
SW3AFAULT
Internal
I2C
Compensation
Z2
SW3AFB
SW3BIN
Z1
VREF
EA
DAC
VIN
I2C
Interface
SW3BMODE
ISENSE
CINSW3B
Controller
SW3B
SW3BLX
EP
Driver
LSW3B
COSW3B
SW3BFAULT
Internal
I2C
Compensation
Z2
SW3BFB
Z1
VREF
EA
DAC
Figure 23. SW3A/B Independent Output Block Diagram
SW3A/B Setup and Control Registers
SW3A/B output voltage is programmable from 0.400 to 3.300 V; however, bit SW3x[6] in register SW3xVOLT is read-only during
normal operation. Its value is determined by the default configuration, or may be changed by using the OTP registers. Therefore,
once SW3x[6] is set to “0”, the output will be limited to the lower output voltages from 0.40 to 1.975 V with 25 mV increments, as
determined by bits SW3x[5:0]. Likewise, once bit SW3x[6] is set to "1", the output voltage will be limited to the higher output
voltage range from 0.800 to 3.300 V with 50 mV increments, as determined by bits SW3x[5:0].
In order to optimize the performance of the regulator, it is recommended that only voltages from 2.00 to 3.300 V be used in the
high range and that that the lower range be used for voltages from 0.400 to 1.975 V.
The output voltage set point is independently programmed for Normal, Standby, and Sleep mode by setting the SW3x[5:0],
SW3xSTBY[5:0], and SW3xOFF[5:0] bits respectively; however, the initial state of the SW3x[6] bit will be copied into the
SW3xSTBY[6] and SW3xOFF[6] bits. Therefore, the output voltage range will remain the same on all three operating modes.
Table 65 shows the output voltage coding valid for SW3x.
Note: Voltage set points of 0.6 V and below are not supported.
PF0100
Analog Integrated Circuit Device Data
70
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 65. SW3A/B Output Voltage Configuration
Low Output Voltage Range(48)
High Output Voltage Range
Set Point
SW3x[6:0]
SW3x Output
Set Point
SW3x[6:0]
SW3xOutput
0
0000000
0000001
0000010
0000011
0000100
0000101
0000110
0000111
0001000
0001001
0001010
0001011
0001100
0001101
0001110
0001111
0010000
0010001
0010010
0010011
0010100
0010101
0010110
0010111
0011000
0011001
0011010
0011011
0011100
0011101
0011110
0011111
0100000
0100001
0100010
0100011
0.4000
0.4250
0.4500
0.4750
0.5000
0.5250
0.5500
0.5750
0.6000
0.6250
0.6500
0.6750
0.7000
0.7250
0.7500
0.7750
0.8000
0.8250
0.8500
0.8750
0.9000
0.9250
0.9500
0.9750
1.0000
1.0250
1.0500
1.0750
1.1000
1.1250
1.1500
1.1750
1.2000
1.2250
1.2500
1.2750
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
1000000
1000001
1000010
1000011
1000100
1000101
1000110
1000111
1001000
1001001
1001010
1001011
1001100
1001101
1001110
1001111
1010000
1010001
1010010
1010011
1010100
1010101
1010110
1010111
1011000
1011001
1011010
1011011
1011100
1011101
1011110
1011111
1100000
1100001
1100010
1100011
0.8000
0.8500
0.9000
0.9500
1.0000
1.0500
1.1000
1.1500
1.2000
1.2500
1.3000
1.3500
1.4000
1.4500
1.5000
1.5500
1.6000
1.6500
1.7000
1.7500
1.8000
1.8500
1.9000
1.9500
2.0000
2.0500
2.1000
2.1500
2.2000
2.2500
2.3000
2.3500
2.4000
2.4500
2.5000
2.5500
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
71
Functional Block Requirements and Behaviors
Power Generation
Table 65. SW3A/B Output Voltage Configuration
Low Output Voltage Range(48)
High Output Voltage Range
Set Point
SW3x[6:0]
SW3x Output
Set Point
SW3x[6:0]
SW3xOutput
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
0100100
0100101
0100110
0100111
0101000
0101001
0101010
0101011
0101100
0101101
0101110
0101111
0110000
0110001
0110010
0110011
0110100
0110101
0110110
0110111
0111000
0111001
0111010
0111011
0111100
0111101
0111110
0111111
1.3000
1.3250
1.3500
1.3750
1.4000
1.4250
1.4500
1.4750
1.5000
1.5250
1.5500
1.5750
1.6000
1.6250
1.6500
1.6750
1.7000
1.7250
1.7500
1.7750
1.8000
1.8250
1.8500
1.8750
1.9000
1.9250
1.9500
1.9750
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
1100100
1100101
1100110
1100111
1101000
1101001
1101010
1101011
1101100
1101101
1101110
1101111
1110000
1110001
1110010
1110011
1110100
1110101
1110110
1110111
1111000
1111001
1111010
1111011
1111100
1111101
1111110
1111111
2.6000
2.6500
2.7000
2.7500
2.8000
2.8500
2.9000
2.9500
3.0000
3.0500
3.1000
3.1500
3.2000
3.2500
3.3000
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Notes
48. For voltages less than 2.0 V, only use set points 0 to 63.
PF0100
Analog Integrated Circuit Device Data
72
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 66 provides a list of registers used to configure and operate SW3A/B. A detailed description on each of these register is
provided on Tables 67 through Table 76.
Table 66. SW3AB Register Summary
Register
SW3AVOLT
Address
Output
0x3C
0x3D
0x3E
0x3F
0x40
0x43
0x44
0x45
0x46
0x47
SW3A Output voltage set point on normal operation
SW3A Output voltage set point on Standby
SW3A Output voltage set point on Sleep
SW3ASTBY
SW3AOFF
SW3AMODE
SW3ACONF
SW3BVOLT
SW3BSTBY
SW3BOFF
SW3A Switching mode selector register
SW3A DVS, phase, frequency and ILIM configuration
SW3B Output voltage set point on normal operation
SW3B Output voltage set point on Standby
SW3B Output voltage set point on Sleep
SW3BMODE
SW3BCONF
SW3B Switching mode selector register
SW3B DVS, phase, frequency and ILIM configuration
Table 67. Register SW3AVOLT - ADDR 0x3C
Name
Bit #
R/W Default
Description
Sets the SW3A output voltage (Independent) or
SW3A/B output voltage (Single/Dual phase),
during normal operation mode. See Table 65 for
all possible configurations.
SW3A
SW3A
5:0
R/W
0x00
Sets the operating output voltage range for SW3A
(Independent) or SW3A/B (Single/Dual phase).
Set during OTP or TBB configuration only. See
Table 65 for all possible configurations.
6
7
R
–
0x00
0x00
UNUSED
UNUSED
Table 68. Register SW3ASTBY - ADDR 0x3D
Name
Bit #
R/W Default
Description
Sets the SW3A output voltage (Independent) or
SW3A/B output voltage (Single/Dual phase),
during Standby mode. See Table 65 for all
possible configurations.
SW3ASTBY
5:0
R/W
0x00
Sets the operating output voltage range for SW3A
(Independent) or SW3A/B (Single/Dual phase) on
Standby mode. This bit inherits the value
configured on bit SW3A[6] during OTP or TBB
configuration. See Table 65 for all possible
configurations.
SW3ASTBY
UNUSED
6
7
R
–
0x00
0x00
UNUSED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
73
Functional Block Requirements and Behaviors
Power Generation
Table 69. Register SW3AOFF - ADDR 0x3E
Name
Bit #
R/W Default
Description
Sets the SW3A output voltage (Independent) or
SW3A/B output voltage (Single/Dual phase),
during Sleep mode. See Table 65 for all possible
configurations.
SW3AOFF
5:0
R/W
0x00
Sets the operating output voltage range for SW3A
(Independent) or SW3A/B (Single/Dual phase) on
Sleep mode. This bit inherits the value configured
on bit SW3A[6] during OTP or TBB configuration.
See Table 65 for all possible configurations.
SW3AOFF
UNUSED
6
7
R
–
0x00
0x00
UNUSED
Table 70. Register SW3AMODE - ADDR 0x3F
Name
Bit #
R/W Default
Description
Sets the SW3A (Independent) or SW3A/B
(Single/Dual phase) switching operation mode.
See Table 30 for all possible configurations.
SW3AMODE
UNUSED
3:0
4
R/W
–
0x80
0x00
UNUSED
Set status of SW3A (Independent) or SW3A/B
(Single/Dual phase) when in Sleep mode.
SW3AOMODE
UNUSED
5
R/W
–
0x00
0x00
0 = OFF
1 = PFM
7:6
UNUSED
Table 71. Register SW3ACONF - ADDR 0x40
Name
Bit #
R/W Default
Description
SW3A current limit level selection
0 = High level current limit
1 = Low level current limit
SW3AILIM
0
R/W
0x00
UNUSED
1
R/W
R/W
0x00
0x00
Unused
SW3A switching frequency selector. See
Table 38.
SW3AFREQ
3:2
SW3APHASE
5:4
7:6
R/W
R/W
0x00
0x00
SW3A Phase clock selection. See Table 36.
SW3A DVS speed selection. See Table 35.
SW3ADVSSPEED
Table 72. Register SW3BVOLT - ADDR 0x43
Name
Bit #
R/W Default
Description
Sets the SW3B output voltage (Independent)
during normal operation mode. See Table 65 for
all possible configurations.
SW3B
SW3B
5:0
R/W
0x00
Sets the operating output voltage range for SW3B
(Independent). Set during OTP or TBB
configuration only. See Table 65 for all possible
configurations.
6
7
R
–
0x00
0x00
UNUSED
UNUSED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
74
Functional Block Requirements and Behaviors
Power Generation
Table 73. Register SW3BSTBY - ADDR 0x44
Name
Bit #
R/W Default
Description
Sets the SW3B output voltage (Independent)
during Standby mode. See Table 65 for all
possible configurations.
SW3BSTBY
5:0
R/W
0x00
Sets the operating output voltage range for SW3B
(Independent) on Standby mode. This bit inherits
the value configured on bit SW3B[6] during OTP
or TBB configuration. See Table 65 for all
possible configurations.
SW3BSTBY
UNUSED
6
7
R
–
0x00
0x00
UNUSED
Table 74. Register SW3BOFF - ADDR 0x45
Name
Bit #
R/W Default
Description
Sets the SW3B output voltage (Independent)
during Sleep mode. See Table 65 for all possible
configurations.
SW3BOFF
5:0
R/W
0x00
Sets the operating output voltage range for SW3B
(Independent) on Sleep mode. This bit inherits
the value configured on bit SW3B[6] during OTP
or TBB configuration. See Table 65 for all
possible configurations.
SW3BOFF
UNUSED
6
7
R
–
0x00
0x00
UNUSED
Table 75. Register SW3BMODE - ADDR 0x46
Name
Bit #
R/W Default
Description
Sets the SW3B (Independent) switching
operation mode. See Table 30 for all possible
configurations.
SW3BMODE
UNUSED
3:0
4
R/W
–
0x80
0x00
UNUSED
Set status of SW3B (Independent) when in Sleep
mode.
SW3BOMODE
UNUSED
5
R/W
–
0x00
0x00
0 = OFF
1 = PFM
7:6
UNUSED
Table 76. Register SW3BCONF - ADDR 0x47
Name
Bit #
R/W Default
Description
SW3B current limit level selection
0 = High level Current limit
1 = Low level Current limit
SW3BILIM
0
R/W
0x00
UNUSED
1
R/W
R/W
R/W
R/W
0x00
0x00
0x00
0x00
Unused
SW3BFREQ
SW3BPHASE
SW3BDVSSPEED
3:2
5:4
7:6
SW3B switching frequency selector. See Table 38.
SW3B Phase clock selection. See Table 36.
SW3B DVS speed selection. See Table 35.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
75
Functional Block Requirements and Behaviors
Power Generation
SW3A/B External Components
Table 77. SW3A/B External Component Requirements
Mode
SW3A/B Single
Phase
SW3A/B Dual
Phase
SW3A Independent
SW3B Independent
Components
Description
(49)
CINSW3A
SW3A Input capacitor
4.7 F
0.1 F
4.7 F
0.1 F
4 x 22 F
–
4.7 F
0.1 F
4.7 F
0.1 F
(49)
CIN3AHF
SW3A Decoupling input capacitor
SW3B Input capacitor
(49)
CINSW3B
4.7 F
4.7 F
(49)
CIN3BHF
SW3B Decoupling input capacitor
SW3A Output capacitor
0.1 F
0.1 F
(49)
COSW3A
2 x 22 F
2 x 22 F
2 x 22 F
2 x 22 F
(49)
COSW3B
SW3B Output capacitor
1.0 H
1.0 H
1.0 H
LSW3A
SW3A Inductor
SW3B Inductor
DCR = 50 m
DCR = 60 m
DCR = 60 m
I
SAT = 3.9 A
I
SAT = 3.0 A
I
SAT = 3.0 A
1.0 H
1.0 H
LSW3B
Notes
–
DCR = 60 m
SAT = 3.0 A
DCR = 60 m
SAT = 3.0 A
I
I
49. Use X5R or X7R capacitors.
SW3A/B Specifications
Table 78. SW3A/B Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], typical external component values, fSW3x = 2.0 MHz, single/dual phase and independent mode
unless, otherwise noted. Typical values are characterized at VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], and 25 °C, unless otherwise noted.
Parameter
SWITCH MODE SUPPLY SW3A/B
Symbol
Min
Typ
Max
Unit
Operating Input Voltage(50)
Nominal Output Voltage
Output Voltage Accuracy
VINSW3x
VSW3x
2.8
-
–
4.5
-
V
V
Table 65
•
PWM, APS 2.8 V < VIN < 4.5 V, 0 < ISW3x < ISW3xMAX
0.625 V < VSW3x < 0.85 V
0.875 V < VSW3x < 1.975 V
2.0 V < VSW3x < 3.3 V
-25
-3.0%
-6.0%
–
–
–
25
3.0%
6.0%
mV
%
VSW3xACC
•
PFM , steady state (2.8 V < VIN < 4.5 V, 0 < ISW3x < 50 mA)
-65
-45
-3.0%
-3.0%
–
–
–
–
65
45
3.0%
3.0%
0.625 V < VSW3x < 0.675 V
0.7 V < VSW3x < 0.85 V
0.875 V < VSW3x < 1.975 V
2.0 V < VSW3x < 3.3 V
Rated Output Load Current (51)
•
2.8 V < VIN < 4.5 V, 0.625 V < VSW3x < 3.3 V
ISW3x
mA
–
–
–
–
2500
1250
PWM, APS mode single/dual phase
PWM, APS mode independent (per phase)
PF0100
Analog Integrated Circuit Device Data
76
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 78. SW3A/B Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], typical external component values, fSW3x = 2.0 MHz, single/dual phase and independent mode
unless, otherwise noted. Typical values are characterized at VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], and 25 °C, unless otherwise noted.
Parameter
SWITCH MODE SUPPLY SW3A/B (CONTINUED)
Current Limiter Peak Current Detection
Symbol
Min
Typ
Max
Unit
•
Single phase (Current through inductor)
SW3xILIM = 0
3.5
2.7
5.0
3.8
6.5
4.9
SW3xILIM = 1
ISW3xLIM
A
•
Independent mode or Dual phase (Current through inductor per
phase)
SW3xILIM = 0
SW3xILIM = 1
1.8
1.3
2.5
1.9
3.3
2.5
Start-up Overshoot
SW3x = 0.0 mA
DVS clk = 25 mV/4 s, VIN = VINSW3x = 4.5 V
I
VSW3xOSH
–
–
–
–
66
mV
µs
Turn-on Time
Enable to 90% of end value
SW3x = 0 mA
tONSW3x
500
I
DVS clk = 25 mV/4 s, VIN = VINSW3x = 4.5 V
Switching Frequency
SW3xFREQ[1:0] = 00
SW3xFREQ[1:0] = 01
SW3xFREQ[1:0] = 10
–
–
–
1.0
2.0
4.0
–
–
–
fSW3x
MHz
Efficiency (Single Phase)
•
f
SW3 = 2.0 MHz, LSW3x 1.0 H
–
–
–
–
–
–
84
85
85
84
80
74
–
–
–
–
–
–
PFM, 1.5 V, 1.0 mA
PFM, 1.5 V, 50 mA
APS, PWM 1.5 V, 500 mA
APS, PWM 1.5 V, 750 mA
APS, PWM 1.5 V, 1250 mA
APS, PWM 1.5 V, 2500 mA
SW3AB
%
Output Ripple
VSW3x
VSW3xLIR
VSW3xLOR
–
–
–
10
–
–
mV
mV
mV
Line Regulation (APS, PWM)
DC Load Regulation (APS, PWM)
Transient Load Regulation
20
20
–
•
Transient Load = 0.0 mA to ISW3x/2, di/dt = 100 mA/s
Overshoot
Undershoot
VSW3xLOTR
mV
–
–
–
–
50
50
Quiescent Current
PFM Mode (Single/Dual Phase)
APS Mode (Single/Dual Phase)
PFM Mode (Independent mode)
APS Mode (SW3A Independent mode)
APS Mode (SW3B Independent mode)
–
–
–
–
–
22
300
50
250
150
–
–
–
–
–
ISW3xQ
µA
SW3A P-MOSFET RDSON
at VIN = VINSW3A = 3.3 V
RONSW3AP
RONSW3AN
ISW3APQ
–
–
–
m
m
µA
215
245
SW3A N-MOSFET RDSON
at VIN = VINSW3A = 3.3 V
258
–
326
7.5
SW3A P-MOSFET Leakage Current
VIN = VINSW3A = 4.5 V
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
77
Functional Block Requirements and Behaviors
Power Generation
Table 78. SW3A/B Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], typical external component values, fSW3x = 2.0 MHz, single/dual phase and independent mode
unless, otherwise noted. Typical values are characterized at VIN = VINSW3x = 3.6 V, VSW3x = 1.5 V, ISW3x = 100 mA,
SW3x_PWRSTG[2:0] = [111], and 25 °C, unless otherwise noted.
Parameter
SWITCH MODE SUPPLY SW3A/B (CONTINUED)
SW3A N-MOSFET Leakage Current
Symbol
Min
Typ
Max
Unit
ISW3ANQ
RONSW3BP
RONSW3BN
ISW3BPQ
–
–
–
–
–
2.5
µA
m
m
µA
V
IN = VINSW3A = 4.5 V
SW3B P-MOSFET RDSON
at VIN = VINSW3B = 3.3 V
215
245
SW3B N-MOSFET RDSON
at VIN = VINSW3B = 3.3 V
258
–
326
7.5
SW3B P-MOSFET Leakage Current
VIN = VINSW3B = 4.5 V
SW3B N-MOSFET Leakage Current
ISW3BPQ
–
–
–
2.5
–
µA
V
IN = VINSW3B = 4.5 V
Discharge Resistance
RSW3xDIS
600
Notes
50. When output is set to > 2.6 V the output will follow the input down when VIN gets near 2.8 V.
51. The higher output voltages available depend on the voltage drop in the conduction path as given by the following equation:
(VINSW3x - VSW3x) = ISW3x* (DCR of Inductor +RONSW3xP + PCB trace resistance).
PF0100
Analog Integrated Circuit Device Data
78
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Figure 24. SW3AB Efficiency Waveforms: VIN = 4.2 V; VOUT = 1.5 V; Consumer Version
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
79
Functional Block Requirements and Behaviors
Power Generation
Figure 25. SW3AB Efficiency Waveforms: VIN = 4.2 V; VOUT = 1.5 V; Extended Industrial Version
6.4.4.6
SW4
SW4 is a 1.0 A rated single phase buck regulator capable of operating in two modes. In its default mode, it operates as a normal
buck regulator with a programmable output between 0.400 and 3.300 V. It is capable of operating in the three available switching
modes: PFM, APS, and PWM, described on Table 30 and configured by the SW4MODE[3:0] bits, as shown in Table 31.
If the system requires DDR memory termination, SW4 can be used in its VTT mode. In the VTT mode, its reference voltage will
track the output voltage of SW3A, scaled by 0.5. Furthermore, when in VTT mode, only the PWM switching mode is allowed. The
VTT mode can be configured by use of VTT bit in the OTP_SW4_CONFIG register.
Figure 26 shows the block diagram and the external component connections for the SW4 regulator.
PF0100
Analog Integrated Circuit Device Data
80
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
VIN
SW4IN
SW4MODE
ISENSE
CINSW4
Controller
SW4
SW4LX
EP
Driver
LSW4
COSW4
SW4FAULT
I2C
Interface
Internal
I2C
Compensation
Z2
SW4FB
Z1
VREF
EA
DAC
Figure 26. SW4 Block Diagram
SW4 Setup and Control Registers
To set the SW4 in regulator or VTT mode, bit VTT of the register OTP_SW4_CONF register on Extended Page 1, is programmed
during OTP or TBB configuration; setting bit VTT to “1” will enable SW4 to operate in VTT mode and “0” in Regulator mode. See
One Time Programmability (OTP) for detailed information on OTP configuration.
In Regulator mode, the SW4 output voltage is programmable from 0.400 to 3.300 V; however, bit SW4[6] in the SW4VOLT
register is read-only during normal operation. Its value is determined by the default configuration, or may be changed by using
the OTP registers. Once SW4[6] is set to “0”, the output will be limited to the lower output voltages, from 0.400 to 1.975 V with
25 mV increments, as determined by the SW4[5:0] bits. Likewise, once the SW4[6] bit is set to "1", the output voltage will be
limited to the higher output voltage range from 0.800 to 3.300 V with 50 mV increments, as determined by the SW4[5:0] bits.
In order to optimize the performance of the regulator, it is recommended that only voltages from 2.000 to 3.300 V be used in the
high range and that that the lower range be used for voltages from 0.400 to 1.975 V.
The output voltage set point is independently programmed for Normal, Standby, and Sleep mode by setting the SW4[5:0],
SW4STBY[5:0], and SW4OFF[5:0] bits, respectively. However, the initial state of the SW4[6] bit will be copied into bits
SW4STBY[6], and SW4OFF[6] bits, so the output voltage range will remain the same on all three operating modes. Table 79
shows the output voltage coding valid for SW4.
Note: Voltage set points of 0.6 V and below are not supported, except in the VTT mode.
Table 79. SW4 Output Voltage Configuration
Low Output Voltage Range(52)
High Output Voltage Range
Set Point
SW4[6:0]
SW4 Output
Set Point
SW4[6:0]
SW4 Output
0
1
0000000
0000001
0000010
0000011
0000100
0000101
0000110
0000111
0001000
0001001
0001010
0001011
0.4000
0.4250
0.4500
0.4750
0.5000
0.5250
0.5500
0.5750
0.6000
0.6250
0.6500
0.6750
64
65
66
67
68
69
70
71
72
73
74
75
1000000
1000001
1000010
1000011
1000100
1000101
1000110
1000111
1001000
1001001
1001010
1001011
0.8000
0.8500
0.9000
0.9500
1.0000
1.0500
1.1000
1.1500
1.2000
1.2500
1.3000
1.3500
2
3
4
5
6
7
8
9
10
11
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
81
Functional Block Requirements and Behaviors
Power Generation
Table 79. SW4 Output Voltage Configuration (continued)
Low Output Voltage Range(52)
High Output Voltage Range
Set Point
SW4[6:0]
SW4 Output
Set Point
SW4[6:0]
SW4 Output
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
0001100
0001101
0001110
0001111
0010000
0010001
0010010
0010011
0010100
0010101
0010110
0010111
0011000
0011001
0011010
0011011
0011100
0011101
0011110
0011111
0100000
0100001
0100010
0100011
0100100
0100101
0100110
0100111
0101000
0101001
0101010
0101011
0101100
0101101
0101110
0101111
0110000
0.7000
0.7250
0.7500
0.7750
0.8000
0.8250
0.8500
0.8750
0.9000
0.9250
0.9500
0.9750
1.0000
1.0250
1.0500
1.0750
1.1000
1.1250
1.1500
1.1750
1.2000
1.2250
1.2500
1.2750
1.3000
1.3250
1.3500
1.3750
1.4000
1.4250
1.4500
1.4750
1.5000
1.5250
1.5500
1.5750
1.6000
76
77
1001100
1001101
1001110
1001111
1010000
1010001
1010010
1010011
1010100
1010101
1010110
1010111
1011000
1011001
1011010
1011011
1011100
1011101
1011110
1011111
1100000
1100001
1100010
1100011
1100100
1100101
1100110
1100111
1101000
1101001
1101010
1101011
1101100
1101101
1101110
1101111
1110000
1.4000
1.4500
1.5000
1.5500
1.6000
1.6500
1.7000
1.7500
1.8000
1.8500
1.9000
1.9500
2.0000
2.0500
2.1000
2.1500
2.2000
2.2500
2.3000
2.3500
2.4000
2.4500
2.5000
2.5500
2.6000
2.6500
2.7000
2.7500
2.8000
2.8500
2.9000
2.9500
3.0000
3.0500
3.1000
3.1500
3.2000
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
PF0100
Analog Integrated Circuit Device Data
82
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 79. SW4 Output Voltage Configuration (continued)
Low Output Voltage Range(52)
High Output Voltage Range
Set Point
SW4[6:0]
SW4 Output
Set Point
SW4[6:0]
SW4 Output
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
0110001
0110010
0110011
0110100
0110101
0110110
0110111
0111000
0111001
0111010
0111011
0111100
0111101
0111110
0111111
1.6250
1.6500
1.6750
1.7000
1.7250
1.7500
1.7750
1.8000
1.8250
1.8500
1.8750
1.9000
1.9250
1.9500
1.9750
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
1110001
1110010
1110011
1110100
1110101
1110110
1110111
1111000
1111001
1111010
1111011
1111100
1111101
1111110
1111111
3.2500
3.3000
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Notes
52. For voltages less than 2.0 V, only use set points 0 to 63.
Full setup and control of SW4 is done through the I2C registers listed on Table 80, and a detailed description of each one of the
registers is provided in Tables 81 to Table 85.
Table 80. SW4 Register Summary
Register
SW4VOLT
Address
Description
0x4A
0x4B
0x4C
0x4D
0x4E
Output voltage set point on normal operation
Output voltage set point on Standby
Output voltage set point on Sleep
SW4STBY
SW4OFF
SW4MODE
SW4CONF
Switching mode selector register
DVS, phase, frequency and ILIM configuration
Table 81. Register SW4VOLT - ADDR 0x4A
Name
Bit #
R/W Default
Description
Sets the SW4 output voltage during normal
operation mode. See Table 79 for all possible
configurations.
SW4
SW4
5:0
R/W
0x00
Sets the operating output voltage range for SW4.
Set during OTP or TBB configuration only. See
Table 79 for all possible configurations.
6
7
R
–
0x00
0x00
UNUSED
UNUSED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
83
Functional Block Requirements and Behaviors
Power Generation
Table 82. Register SW4STBY - ADDR 0x4B
Name
Bit #
R/W Default
Description
Sets the SW4 output voltage during Standby
mode. See Table 79 for all possible
configurations.
SW4STBY
5:0
R/W
0x00
Sets the operating output voltage range for SW4
on Standby mode. This bit inherits the value
configured on bit SW4[6] during OTP or TBB
configuration. See Table 79 for all possible
configurations.
SW4STBY
UNUSED
6
7
R
–
0x00
0x00
UNUSED
Table 83. Register SW4OFF - ADDR 0x4C
Name
SW4OFF
Bit #
R/W Default
Description
Sets the SW4 output voltage during Sleep mode.
See Table 79 for all possible configurations.
5:0
R/W
0x00
Sets the operating output voltage range for SW4
on Sleep mode. This bit inherits the value
configured on bit SW4[6] during OTP or TBB
configuration. See Table 79 for all possible
configurations.
SW4OFF
UNUSED
6
7
R
–
0x00
0x00
UNUSED
Table 84. Register SW4MODE - ADDR 0x4D
Name
SW4MODE
Bit #
R/W Default
Description
Sets the SW4 switching operation mode.
See Table 30 for all possible configurations.
3:0
4
R/W
–
0x80
0x00
UNUSED
UNUSED
Set status of SW4 when in Sleep mode
SW4OMODE
UNUSED
5
R/W
–
0x00
0x00
0 = OFF
1 = PFM
7:6
UNUSED
Table 85. Register SW4CONF - ADDR 0x4E
Name
Bit #
R/W Default
Description
SW4 current limit level selection
0 = High level Current limit
1 = Low level Current limit
SW4ILIM
0
R/W
0x00
UNUSED
1
R/W
R/W
R/W
R/W
0x00
0x00
0x00
0x00
Unused
SW4FREQ
3:2
5:4
7:6
SW4 switching frequency selector. See Table 38.
SW4 Phase clock selection. See Table 36.
SW4 DVS speed selection. See Table 35.
SW4PHASE
SW4DVSSPEED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
84
Functional Block Requirements and Behaviors
Power Generation
SW4 External Components
Table 86. SW4 External Component Requirements
Components
Description
SW4 Input capacitor
Values
(53)
CINSW4
4.7 F
0.1 F
(53)
CIN4HF
COSW4
SW4 Decoupling input capacitor
SW4 Output capacitor
(53)
2 x 22 F
1.0 H
LSW4
SW4 Inductor
DCR = 60 m
I
SAT = 3.0 A
Notes
53. Use X5R or X7R capacitors.
SW4 Specifications
Table 87. SW4 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW4 = 3.6 V, VSW4 = 1.8 V, ISW4 = 100 mA,
SW4_PWRSTG[2:0] = [101], typical external component values, fSW4 = 2.0 MHz, single/dual phase and independent mode
unless, otherwise noted. Typical values are characterized at VIN = VINSW4 = 3.6 V, VSW4 = 1.8 V, ISW4 = 100 mA,
SW4_PWRSTG[2:0] = [101], and 25 °C, unless otherwise noted.
Parameter
SWITCH MODE SUPPLY SW4
Symbol
Min
Typ
Max
Unit
Operating Input Voltage (54)
VINSW4
2.8
–
4.5
V
V
Nominal Output Voltage
Normal operation
VTT Mode
VSW4
–
–
Table 79
VSW3AFB/2
–
–
SWITCH MODE SUPPLY SW4 (CONTINUED)
Output Voltage Accuracy
•
PWM, APS, 2.8 V < VIN < 4.5 V, 0 < ISW4 < 1.0 A
0.625 V < VSW4 < 0.85 V
0.875 V < VSW4 < 1.975 V
2.0 V < VSW4 < 3.3 V
-25
-3.0
-6.0
–
–
–
25
3.0
6.0
mV
%
%
•
PFM, steady state, 2.8 V < VIN < 4.5 V, 0 < ISW4 < 50 mA
VSW4ACC
-65
-45
-3.0
-3.0
–
–
–
–
65
45
3.0
3.0
mV
mV
%
0.625 V < VSW4 < 0.675 V
0.7 V < VSW4 < 0.85 V
0.875 V < VSW4 < 1.975 V
2.0 V < VSW4 < 3.3 V
%
-40
–
–
–
40
mV
mA
•
VTT Mode , 2.8 V < VIN < 4.5 V, 0 < ISW4 < 1.0 A
Rated Output Load Current (55)
ISW4
1000
2.8 V < VIN < 4.5 V, 0.625 V < VSW4 < 3.3 V
Current Limiter Peak Current Detection
Current through inductor
SW4ILIM = 0
ISW4LIM
A
1.4
1.0
2.0
1.5
3.0
2.4
SW4ILIM = 1
Start-up Overshoot
I
SW4 = 0.0 mA
VSW4OSH
–
–
66
mV
DVS clk = 25 mV/4 s, VIN = VINSW4 = 4.5 V
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
85
Functional Block Requirements and Behaviors
Power Generation
Table 87. SW4 Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSW4 = 3.6 V, VSW4 = 1.8 V, ISW4 = 100 mA,
SW4_PWRSTG[2:0] = [101], typical external component values, fSW4 = 2.0 MHz, single/dual phase and independent mode
unless, otherwise noted. Typical values are characterized at VIN = VINSW4 = 3.6 V, VSW4 = 1.8 V, ISW4 = 100 mA,
SW4_PWRSTG[2:0] = [101], and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
Turn-on Time
Enable to 90% of end value
SW4 = 0.0 mA
tONSW4
–
–
500
µs
I
DVS clk = 25 mV/4 s, VIN = VINSW4 = 4.5 V
Switching Frequency
SW4FREQ[1:0] = 00
SW4FREQ[1:0] = 01
SW4FREQ[1:0] = 10
–
–
–
1.0
2.0
4.0
–
–
–
fSW4
MHz
Efficiency
•
f
SW4 = 2.0 MHz, LSW4 = 1.0 H
–
–
–
–
–
81
78
87
88
83
–
–
–
–
–
PFM, 1.8 V, 1.0 mA
PFM, 1.8 V, 50 mA
APS, PWM 1.8 V, 200 mA
APS, PWM 1.8 V, 500 mA
APS, PWM 1.8 V, 1000 mA
SW4
%
–
–
–
78
76
66
–
–
–
PWM 0.75 V, 200 mA
PWM 0.75 V, 500 mA
PWM 0.75 V, 1000 mA
Output Ripple
VSW4
VSW4LIR
VSW4LOR
–
–
–
10
–
–
mV
mV
mV
Line Regulation (APS, PWM)
DC Load Regulation (APS, PWM)
Transient Load Regulation
20
20
–
•
Transient Load = 0.0 mA to 500 mA, di/dt = 100 mA/s
Overshoot
Undershoot
VSW4LOTR
–
–
–
–
mV
50
50
SWITCH MODE SUPPLY SW4 (CONTINUED)
Quiescent Current
PFM Mode
ISW4Q
–
–
22
145
–
–
µA
APS Mode
SW4 P-MOSFET RDSON
at VIN = VINSW4 = 3.3 V
RONSW4P
RONSW4N
ISW4PQ
–
–
–
236
293
–
274
378
6.0
m
m
µA
SW4 N-MOSFET RDSON
at VIN = VINSW4 = 3.3 V
SW4 P-MOSFET Leakage Current
V
IN = VINSW4 = 4.5 V
SW4 N-MOSFET Leakage Current
VIN = VINSW4 = 4.5 V
ISW4NQ
–
–
–
2.0
–
µA
Discharge Resistance
RSW4DIS
600
Notes
54. When output is set to > 2.6 V the output will follow the input down when VIN gets near 2.8 V.
55. The higher output voltages available depend on the voltage drop in the conduction path as given by the following equation:
(VINSW4 - VSW4) = ISW4* (DCR of Inductor +RONSW4P + PCB trace resistance).
PF0100
Analog Integrated Circuit Device Data
86
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Figure 27. SW4 Efficiency Waveforms: VIN = 4.2 V; VOUT = 1.8 V; Consumer Version
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
87
Functional Block Requirements and Behaviors
Power Generation
Figure 28. SW4 Efficiency Waveforms: VIN = 4.2 V; VOUT = 1.8 V; Extended Industrial Version
6.4.5 Boost Regulator
SWBST is a boost regulator with a programmable output from 5.0 to 5.15 V. SWBST can supply the VUSB regulator for the USB
PHY in OTG mode, as well as the VBUS voltage. Note that the parasitic leakage path for a boost regulator will cause the
SWBSTOUT and SWBSTFB voltage to be a Schottky drop below the input voltage whenever SWBST is disabled. The switching
NMOS transistor is integrated on-chip. Figure 29 shows the block diagram and component connection for the boost regulator.
PF0100
Analog Integrated Circuit Device Data
88
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
VIN
CINBST
SWBSTIN
SWBSTLX
LBST
DBST
SWBSTMODE
VOBST
Driver
I2C
Interface
OC
SWBSTFAULT
Controller
RSENSE
EP
VREFSC
VREFUV
SC
UV
SWBSTFB
Internal
Compensation
COSWBST
Z2
Z1
EA
VREF
Figure 29. Boost Regulator Architecture
6.4.5.1
SWBST Setup and Control
Boost regulator control is done through a single register SWBSTCTL described in Table 88. SWBST is included in the power-up
sequence if its OTP power-up timing bits, SWBST_SEQ[4:0], are not all zeros.
Table 88. Register SWBSTCTL - ADDR 0x66
Name
Bit #
R/W
Default
Description
Set the output voltage for SWBST
00 = 5.000 V
SWBST1VOLT
1:0
R/W
0x00
01 = 5.050 V
10 = 5.100 V
11 = 5.150 V
Set the Switching mode on Normal operation
00 = OFF
SWBST1MODE
UNUSED
3:2
4
R
–
0x02
0x00
0x02
0x00
01 = PFM
10 = Auto (Default)(56)
11 = APS
UNUSED
Set the Switching mode on Standby
00 = OFF
SWBST1STBYMODE
6:5
7
R/W
–
01 = PFM
10 = Auto (Default)(56)
11 = APS
UNUSED
Notes
UNUSED
56. In Auto mode, the controller automatically switches between PFM and APS modes depending on the load current.
The SWBST regulator starts up by default in the Auto mode if SWBST is part of the startup sequence.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
89
Functional Block Requirements and Behaviors
Power Generation
6.4.5.2
SWBST External Components
Table 89. SWBST External Component Requirements
Components
Description
Values
(57)
CINBST
SWBST input capacitor
SWBST decoupling input capacitor
SWBST output capacitor
SWBST inductor
10 F
0.1 F
(57)
CINBSTHF
(57)
COBST
LSBST
DBST
2 x 22 F
2.2 H
SWBST boost diode
1.0 A, 20 V Schottky
Notes
57. Use X5R or X7R capacitors.
6.4.5.3
SWBST Specifications
Table 90. SWBST Electrical Specifications
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSWBST = 3.6 V, VSWBST = 5.0 V, ISWBST = 100 mA, typical
external component values, fSWBST = 2.0 MHz, otherwise noted. Typical values are characterized at VIN = VINSWBST = 3.6 V,
VSWBST = 5.0 V, ISWBST = 100 mA, and 25 °C, unless otherwise noted.
Parameters
SWITCH MODE SUPPLY SWBST
Symbol
Min
Typ
Max
Units
Input Voltage Range
VINSWBST
VSWBST
2.8
–
–
4.5
–
V
V
Nominal Output Voltage
Table 88
Output Voltage Accuracy
2.8 V VIN 4.5 V
VSWBSTACC
-4.0
–
–
–
3.0
%
0 < ISWBST < ISWBSTMAX
Output Ripple
2.8 V VIN 4.5 V
0 < ISWBST < ISWBSTMAX, excluding reverse recovery of
mV
Vp-p
VSWBST
120
Schottky diode
DC Load Regulation
mV/
mA
VSWBSTLOR
VSWBSTLIR
–
–
0.5
50
–
–
0 < ISWBST < ISWBSTMAX
DC Line Regulation
mV
mA
A
2.8 V VIN 4.5 V, ISWBST = ISWBSTMAX
Continuous Load Current
2.8 V VIN 3.0 V
ISWBST
–
–
–
–
500
600
3.0 V VIN 4.5 V
Quiescent Current
AUTO
ISWBSTQ
–
222
289
MOSFET on Resistance
Peak Current Limit (58)
Start-up Overshoot
RDSONBST
ISWBSTLIM
–
206
306
m
1400
2200
3200
mA
VSWBSTOSH
–
–
–
–
500
300
mV
mV
I
SWBST = 0.0 mA
Transient Load Response
SWBST from 1.0 to 100 mA in 1.0 µs
I
VSWBSTTR
Maximum transient Amplitude
Transient Load Response
I
SWBST from 100 to 1.0 mA in 1.0 µs
VSWBSTTR
–
–
300
mV
Maximum transient Amplitude
PF0100
Analog Integrated Circuit Device Data
90
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 90. SWBST Electrical Specifications (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = VINSWBST = 3.6 V, VSWBST = 5.0 V, ISWBST = 100 mA, typical
external component values, fSWBST = 2.0 MHz, otherwise noted. Typical values are characterized at VIN = VINSWBST = 3.6 V,
VSWBST = 5.0 V, ISWBST = 100 mA, and 25 °C, unless otherwise noted.
Parameters
Symbol
Min
Typ
Max
Units
Transient Load Response
SWBST from 1.0 to 100 mA in 1.0 µs
Time to settle 80% of transient
I
tSWBSTTR
–
–
500
µs
Transient Load Response
SWBST from 100 to 1.0 mA in 1.0 µs
I
tSWBSTTR
–
–
–
20
ms
µA
Time to settle 80% of transient
NMOS Off Leakage
ISWBSTHSQ
1.0
5.0
SWBSTIN = 4.5 V, SWBSTMODE [1:0] = 00
Turn-on Time
tONSWBST
fSWBST
–
–
–
–
2.0
–
ms
MHz
%
Enable to 90% of VSWBST, ISWBST = 0.0 mA
Switching Frequency
2.0
86
Efficiency
SWBST
–
ISWBST = ISWBSTMAX
Notes
58. Only in Auto mode.
6.4.6 LDO Regulators Description
This section describes the LDO regulators provided by the PF0100. All regulators use the main bandgap as reference. Refer to
Bias and References Block Description section for further information on the internal reference voltages.
A Low Power mode is automatically activated by reducing bias currents when the load current is less than I_Lmax/5. However,
the lowest bias currents may be attained by forcing the part into its Low Power mode by setting the VGENxLPWR bit. The use
of this bit is only recommended when the load is expected to be less than I_Lmax/50, otherwise performance may be degraded.
When a regulator is disabled, the output will be discharged by an internal pull-down. The pull-down is also activated when
RESETBMCU is low.
VINx
VINx
VREF
_
+
VGENxEN
VGENxLPWR
VGENx
VGENx
I2C
Interface
CGENx
VGENx
Discharge
Figure 30. General LDO Block Diagram
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
91
Functional Block Requirements and Behaviors
Power Generation
6.4.6.1
Transient Response Waveforms
Idealized stimulus and response waveforms for transient line and transient load tests are depicted in Figure 31. Note that the
transient line and load response refers to the overshoot, or undershoot only, excluding the DC shift.
IMAX
ILOAD
IMAX/10
1.0 us
1.0 us
Transient Load Stimulus
IL = IMAX/10
IL = IMAX
Overshoot
VOUT
Undershoot
VOUT Transient Load Response
VINx_INITIAL
VINx
VINx_FINAL
10 us
10 us
Transient Line Stimulus
VINx_FINAL
VINx_INITIAL
Overshoot
VOUT
Undershoot
VOUT Transient Line Response
Figure 31. Transient Waveforms
PF0100
Analog Integrated Circuit Device Data
92
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
6.4.6.2
Short-circuit Protection
All general purpose LDOs have short-circuit protection capability. The Short-circuit Protection (SCP) system includes debounced
fault condition detection, regulator shutdown, and processor interrupt generation, to contain failures and minimize the chance of
product damage. If a short-circuit condition is detected, the LDO will be disabled by resetting its VGENxEN bit, while at the same
time, an interrupt VGENxFAULTI will be generated to flag the fault to the system processor. The VGENxFAULTI interrupt is
maskable through the VGENxFAULTM mask bit.
The SCP feature is enabled by setting the REGSCPEN bit. If this bit is not set, the regulators will not automatically be disabled
upon a short-circuit detection. However, the current limiter will continue to limit the output current of the regulator. By default, the
REGSCPEN is not set; therefore, at start-up none of the regulators will be disabled if an overloaded condition occurs. A fault
interrupt, VGENxFAULTI, will be generated in an overload condition regardless of the state of the REGSCPEN bit. See Table 91
for SCP behavior configuration.
Table 91. Short-circuit Behavior
REGSCPEN[0]
Short-circuit Behavior
0
1
Current limit
Shutdown
6.4.6.3
LDO Regulator Control
Each LDO is fully controlled through its respective VGENxCTL register. This register enables the user to set the LDO output
voltage according to Table 92 for VGEN1 and VGEN2; and uses the voltage set point on Table 93 for VGEN3 through VGEN6.
Table 92. VGEN1, VGEN2 Output Voltage Configuration
Set Point
VGENx[3:0]
VGENx Output (V)
0
1
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
0.800
0.850
0.900
0.950
1.000
1.050
1.100
1.150
1.200
1.250
1.300
1.350
1.400
1.450
1.500
1.550
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
93
Functional Block Requirements and Behaviors
Power Generation
Table 93. VGEN3/ 4/ 5/ 6 Output Voltage Configuration
Set Point
VGENx[3:0]
VGENx Output (V)
0
1
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
1.80
1.90
2.00
2.10
2.20
2.30
2.40
2.50
2.60
2.70
2.80
2.90
3.00
3.10
3.20
3.30
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Besides the output voltage configuration, the LDOs can be enabled or disabled at anytime during normal mode operation, as well
as programmed to stay “ON” or be disabled when the PMIC enters Standby mode. Each regulator has associated I2C bits for
this. Table 94 presents a summary of all valid combinations of the control bits on VGENxCTL register and the expected behavior
of the LDO output.
Table 94. LDO Control
VGENxEN
VGENxLPWR
VGENxSTBY STANDBY(59)
VGENxOUT
0
1
1
1
1
1
X
0
1
X
0
1
X
0
0
1
1
1
X
X
X
0
Off
On
Low Power
On
1
Off
1
Low Power
Notes
59. STANDBY refers to a Standby event as described earlier.
PF0100
Analog Integrated Circuit Device Data
94
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
For more detail information, Table 95 through Table 100 provide a description of all registers necessary to operate all six general
purpose LDO regulators.
Table 95. Register VGEN1CTL - ADDR 0x6C
Name
Bit #
R/W Default
Description
Sets VGEN1 output voltage.
See Table 92 for all possible configurations.
VGEN1
3:0
R/W
–
0x80
0x00
0x00
Enables or Disables VGEN1 output
VGEN1EN
4
5
0 = OFF
1 = ON
Set VGEN1 output state when in Standby. Refer
to Table 94.
VGEN1STBY
R/W
Enable Low Power Mode for VGEN1. Refer to
Table 94.
VGEN1LPWR
UNUSED
6
7
R/W
–
0x00
0x00
UNUSED
Table 96. Register VGEN2CTL - ADDR 0x6D
Name
Bit #
R/W Default
Description
Sets VGEN2 output voltage.
See Table 92 for all possible configurations.
VGEN2
3:0
R/W
–
0x80
0x00
0x00
Enables or Disables VGEN2 output
VGEN2EN
4
5
0 = OFF
1 = ON
Set VGEN2 output state when in Standby. Refer
to Table 94.
VGEN2STBY
R/W
Enable Low Power Mode for VGEN2. Refer to
Table 94.
VGEN2LPWR
UNUSED
6
7
R/W
–
0x00
0x00
UNUSED
Table 97. Register VGEN3CTL - ADDR 0x6E
Name
Bit #
R/W Default
Description
Sets VGEN3 output voltage.
See Table 93 for all possible configurations.
VGEN3
3:0
R/W
–
0x80
0x00
0x00
Enables or Disables VGEN3 output
VGEN3EN
4
5
0 = OFF
1 = ON
Set VGEN3 output state when in Standby. Refer
to Table 94.
VGEN3STBY
R/W
Enable Low Power Mode for VGEN3. Refer to
Table 94.
VGEN3LPWR
UNUSED
6
7
R/W
–
0x00
0x00
UNUSED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
95
Functional Block Requirements and Behaviors
Power Generation
Table 98. Register VGEN4CTL - ADDR 0x6F
Name
Bit #
R/W Default
Description
Sets VGEN4 output voltage.
See Table 93 for all possible configurations.
VGEN4
3:0
R/W
–
0x80
0x00
0x00
Enables or Disables VGEN4 output
VGEN4EN
4
5
0 = OFF
1 = ON
Set VGEN4 output state when in Standby. Refer
to Table 94.
VGEN4STBY
R/W
Enable Low Power Mode for VGEN4. Refer to
Table 94.
VGEN4LPWR
UNUSED
6
7
R/W
–
0x00
0x00
UNUSED
Table 99. Register VGEN5CTL - ADDR 0x70
Name
Bit #
R/W Default
Description
Sets VGEN5 output voltage.
See Table 93 for all possible configurations.
VGEN5
3:0
R/W
–
0x80
0x00
0x00
Enables or Disables VGEN5 output
VGEN5EN
4
5
0 = OFF
1 = ON
Set VGEN5 output state when in Standby. Refer
to Table 94.
VGEN5STBY
R/W
Enable Low Power Mode for VGEN5. Refer to
Table 94.
VGEN5LPWR
UNUSED
6
7
R/W
–
0x00
0x00
UNUSED
Table 100. Register VGEN6CTL - ADDR 0x71
Name
Bit #
R/W Default
Description
Sets VGEN6 output voltage.
See Table 93 for all possible configurations.
VGEN6
3:0
R/W
–
0x80
0x00
0x00
Enables or Disables VGEN6 output
VGEN6EN
4
5
0 = OFF
1 = ON
Set VGEN6 output state when in Standby. Refer
to Table 94.
VGEN6STBY
R/W
Enable Low Power Mode for VGEN6. Refer to
Table 94.
VGEN6LPWR
UNUSED
6
7
R/W
–
0x00
0x00
UNUSED
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
96
Functional Block Requirements and Behaviors
Power Generation
6.4.6.4
External Components
Table 101 lists the typical component values for the general purpose LDO regulators.
Table 101. LDO External Components
Regulator
Output Capacitor (F)(60)
VGEN1
VGEN2
VGEN3
VGEN4
VGEN5
VGEN6
2.2
4.7
2.2
4.7
2.2
2.2
Notes
60. Use X5R/X7R ceramic capacitors.
6.4.6.5
VGEN1
LDO Specifications
Table 102. VGEN1 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN1 = 3.0 V, VGEN1[3:0] = 1111, IGEN1 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, IN1 = 3.0 V,
VGEN1[3:0] = 1111, IGEN1 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN1
Operating Input Voltage
Nominal Output Voltage
Operating Load Current
VGEN1 DC
VIN1
VGEN1NOM
IGEN1
1.75
–
–
Table 92
–
3.40
–
V
V
0.0
100
mA
Output Voltage Tolerance
1.75 V < VIN1 < 3.4 V
VGEN1TOL
-3.0
–
–
3.0
–
%
0.0 mA < IGEN1 < 100 mA
VGEN1[3:0] = 0000 to 1111
Load Regulation
mV/
mA
(VGEN1 at IGEN1 = 100 mA) - (VGEN1 at IGEN1 = 0.0 mA)
For any 1.75 V < VIN1 < 3.4 V
VGEN1LOR
0.15
Line Regulation
mV/
mA
(VGEN1 at VIN1 = 3.4 V) - (VGEN1 at VIN1 = 1.75 V)
For any 0.0 mA < IGEN1 < 100 mA
VGEN1LIR
IGEN1LIM
IGEN1OCP
–
0.30
167
–
–
Current Limit
122
115
200
200
mA
mA
I
GEN1 when VGEN1 is forced to VGEN1NOM/2
Overcurrent Protection Threshold
IGEN1 required to cause the SCP function to disable LDO when
REGSCPEN = 1
Quiescent Current
No load, Change in IVIN and IVIN1
When VGEN1 enabled
IGEN1Q
–
14
–
A
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
97
Functional Block Requirements and Behaviors
Power Generation
Table 102. VGEN1 Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN1 = 3.0 V, VGEN1[3:0] = 1111, IGEN1 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, IN1 = 3.0 V,
VGEN1[3:0] = 1111, IGEN1 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN1 AC AND TRANSIENT
PSRR(61)
•
IGEN1 = 75 mA, 20 Hz to 20 kHz
PSRRVGEN1
dB
50
37
60
45
–
–
VGEN1[3:0] = 0000 - 1101
VGEN1[3:0] = 1110, 1111
Output Noise Density
V
IN1 = 1.75 V, IGEN1 = 75 mA
dBV/
Hz
100 Hz – <1.0 kHz
1.0 kHz – <10 kHz
10 kHz – 1.0 MHz
NOISEVGEN1
–
–
–
-108
-118
-124
-100
-108
-112
Turn-on Slew Rate
•
10% to 90% of end value
•
1.75 V VIN1 3.4 V, IGEN1 = 0.0 mA
VGEN1[3:0] = 0000 to 0111
VGEN1[3:0] = 1000 to 1111
SLWRVGEN1
mVs
s
–
–
–
–
12.5
16.5
Turn-On Time
Enable to 90% of end value, VIN1 = 1.75 V, 3.4 V
GEN1 = 0.0 mA
GEN1tON
60
–
500
I
Turn-Off Time
Disable to 10% of initial value, VIN1 = 1.75 V
GEN1tOFF
GEN1OSHT
–
–
–
10
ms
%
IGEN1 = 0.0 mA
Start-Up Overshoot
1.0
2.0
VIN1 = 1.75 V, 3.4 V, IGEN1 = 0.0 mA
Transient Load Response
•
VIN1 = 1.75 V, 3.4 V
VGEN1LOTR
–
–
–
3.0
8.0
%
IGEN1 = 10 to 100 mA in 1.0 s. Peak of overshoot or undershoot
of VGEN1 with respect to final value
Refer to Figure 31
•
Transient Line Response
•
I
GEN1 = 75 mA
VIN1INITIAL = 1.75 V to VIN1FINAL = 2.25 V for
VGEN1[3:0] = 0000 to 1101
VGEN1LITR
5.0
mV
VIN1INITIAL = VGEN1+0.3 V to VIN1FINAL = VGEN1+0.8 V for
VGEN1[3:0] = 1110, 1111
•
Refer to Figure 31
Notes
61. The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied
separately from the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to
operate in the dropout region of the regulator under test.
PF0100
Analog Integrated Circuit Device Data
98
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
VGEN2
Table 103. VGEN2 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN1 = 3.0 V, VGEN2[3:0] = 1111, IGEN2 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6V, VIN1 = 3.0 V,
VGEN2[3:0] = 1111, IGEN2 = 10mA and 25°C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN2
Operating Input Voltage
Nominal Output Voltage
Operating Load Current
VIN1
VGEN2NOM
IGEN2
1.75
–
–
Table 92
–
3.40
–
V
V
0.0
250
mA
VGEN2 ACTIVE MODE - DC
Output VoltageTolerance
1.75 V < VIN1 < 3.4 V
VGEN2TOL
-3.0
–
3.0
%
0.0 mA < IGEN2 < 250 mA
VGEN2[3:0] = 0000 to 1111
Load Regulation
mV/
mA
(VGEN2 at IGEN2 = 250 mA) - (VGEN2 at IGEN2 = 0.0 mA)
For any 1.75 V < VIN1 < 3.4 V
VGEN2LOR
–
–
0.05
0.50
–
–
Line Regulation
mV/
mA
(VGEN2 at VIN1 = 3.4 V) - (VGEN2 at VIN1 = 1.75 V)
For any 0.0 mA < IGEN2 < 250 mA
VGEN2LIR
Current Limit
I
GEN2 when VGEN2 is forced to VGEN2NOM/2
IGEN2LIM
mA
MMPF0100
MMPF0100A
333
305
417
417
510
510
Overcurrent Protection Threshold
I
GEN2 required to cause the SCP function to disable LDO when
REGSCPEN = 1
MMPF0100
MMPF0100A
IGEN2OCP
mA
300
290
–
–
500
500
Quiescent Current
No load, Change in IVIN and IVIN1
When VGEN2 enabled
IGEN2Q
–
16
–
A
VGEN2 AC AND TRANSIENT
PSRR(62)
•
IGEN2 = 187.5 mA, 20 Hz to 20 kHz
PSRRVGEN2
dB
50
37
60
45
–
–
VGEN2[3:0] = 0000 - 1101
VGEN2[3:0] = 1110, 1111
Output Noise Density
IN1 = 1.75 V, IGEN2 = 187.5 mA
•
V
dBV/
Hz
NOISEVGEN2
–
–
–
-108
-118
-124
-100
-108
-112
100 Hz – <1.0 kHz
1.0 kHz – <10 kHz
10 kHz – 1.0 MHz
Turn-On Slew Rate
•
10% to 90% of end value
•
1.75 V VIN1 3.4 V, IGEN2 = 0.0 mA
VGEN2[3:0] = 0000 to 0111
VGEN2[3:0] = 1000 to 1111
SLWRVGEN2
mVs
s
–
–
–
–
12.5
16.5
Turn-On Time
Enable to 90% of end value, VIN1 = 1.75 V, 3.4 V
GEN2 = 0.0 mA
GEN2tON
60
–
500
I
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
99
Functional Block Requirements and Behaviors
Power Generation
Table 103. VGEN2 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN1 = 3.0 V, VGEN2[3:0] = 1111, IGEN2 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6V, VIN1 = 3.0 V,
VGEN2[3:0] = 1111, IGEN2 = 10mA and 25°C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN2 AC AND TRANSIENT (CONTINUED)
Turn-Off Time
Disable to 10% of initial value, VIN1 = 1.75 V
IGEN2 = 0.0 mA
GEN2tOFF
GEN2OSHT
–
–
–
10
ms
%
Start-up Overshoot
1.0
2.0
V
IN1 = 1.75 V, 3.4 V, IGEN2 = 0.0 mA
Transient Load Response
V
IN1 = 1.75 V, 3.4 V
I
GEN2 = 25 to 250 mA in 1.0 s
VGEN2LOTR
–
–
–
3.0
8.0
%
Peak of overshoot or undershoot of VGEN2 with respect to final
value
Refer to Figure 31
Transient Line Response
IGEN2 = 187.5 mA
VIN1INITIAL = 1.75 V to VIN1FINAL = 2.25 V for
VGEN2[3:0] = 0000 to 1101
VGEN2LITR
5.0
mV
VIN1INITIAL = VGEN2+0.3 V to VIN1FINAL = VGEN2+0.8 V for
VGEN2[3:0] = 1110, 1111
Refer to Figure 31
Notes
62. The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied
separately from the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to
operate in the dropout region of the regulator under test.
PF0100
Analog Integrated Circuit Device Data
100
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
VGEN3
Table 104. VGEN3 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN2 = 3.6 V, VGEN3[3:0] = 1111, IGEN3 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN2 = 3.6 V,
VGEN3[3:0] = 1111, IGEN3 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN3
Operating Input Voltage
2.8
VGEN3NOM
0.250
1.8 V VGEN3NOM 2.5 V
VIN2
–
–
3.6
3.6
V
+
2.6 V VGEN3NOM 3.3 V(63)
Nominal Output Voltage
Operating Load Current
VGEN3 DC
VGEN3NOM
IGEN3
–
Table 93
–
–
V
0.0
100
mA
Output Voltage Tolerance
VIN2MIN < VIN2 < 3.6 V
VGEN3TOL
-3.0
–
–
3.0
–
%
0.0 mA < IGEN3 < 100 mA
VGEN3[3:0] = 0000 to 1111
Load Regulation
mV/
mA
(VGEN3 at IGEN3 = 100 mA) - (VGEN3 at IGEN3 = 0.0 mA)
For any VIN2MIN < VIN2 < 3.6 V
VGEN3LOR
0.07
Line Regulation
mV/
mA
(VGEN3 at VIN2 = 3.6 V) - (VGEN3 at VIN2MIN
For any 0.0 mA < IGEN3 < 100 mA
)
VGEN3LIR
IGEN3LIM
IGEN3OCP
–
0.8
167
–
–
Current Limit
GEN3 when VGEN3 is forced to VGEN3NOM/2
127
120
200
200
mA
mA
I
Over-current Protection Threshold
GEN3 required to cause the SCP function to disable LDO when
I
REGSCPEN = 1
Quiescent Current
No load, Change in IVIN and IVIN2
When VGEN3 enabled
IGEN3Q
–
13
–
A
VGEN3 AC AND TRANSIENT
PSRR(64)
•
IGEN3 = 75 mA, 20 Hz to 20 kHz
PSRRVGEN3
dB
35
55
40
60
–
–
VGEN3[3:0] = 0000 - 1110, VIN2 = VIN2MIN + 100 mV
VGEN3[3:0] = 0000 - 1000, VIN2 = VGEN3NOM + 1.0 V
Output Noise Density
IN2 = VIN2MIN, IGEN3 = 75 mA
•
V
dBV/
Hz
NOISEVGEN3
–
–
–
-114
-129
-135
-102
-123
-130
100 Hz – <1.0 kHz
1.0 kHz – <10 kHz
10 kHz – 1.0 MHz
Turn-On Slew Rate
•
10% to 90% of end value
•
VIN2MINVIN2 3.6 V, IGEN3 = 0.0 mA
SLWRVGEN3
–
–
–
–
–
–
–
–
22.0
26.5
30.5
34.5
mVs
VGEN3[3:0] = 0000 to 0011
VGEN3[3:0] = 0100 to 0111
VGEN3[3:0] = 1000 to 1011
VGEN3[3:0] = 1100 to 1111
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
101
Functional Block Requirements and Behaviors
Power Generation
Table 104. VGEN3 Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN2 = 3.6 V, VGEN3[3:0] = 1111, IGEN3 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN2 = 3.6 V,
VGEN3[3:0] = 1111, IGEN3 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN3 AC AND TRANSIENT (CONTINUED)
Turn-On Time
Enable to 90% of end value, VIN2 = VIN2MIN, 3.6 V
GEN3tON
60
–
500
s
I
GEN3 = 0.0 mA
Turn-Off Time
Disable to 10% of initial value, VIN2 = VIN2MIN
IGEN3 = 0.0 mA
GEN3tOFF
GEN3OSHT
–
–
–
10
ms
%
Start-up Overshoot
1.0
2.0
V
IN2 = VIN2MIN, 3.6 V, IGEN3 = 0.0 mA
Transient Load Response
V
IN2 = VIN2MIN, 3.6 V
I
GEN3 = 10 to 100 mA in 1.0s
VGEN3LOTR
–
–
3.0
8.0
%
Peak of overshoot or undershoot of VGEN3 with respect to final
value. Refer to Figure 31
Transient Line Response
I
GEN3 = 75 mA
VIN2INITIAL = 2.8 V to VIN2FINAL = 3.3 V for
GEN3[3:0] = 0000 to 0111
VIN2INITIAL = VGEN3+0.3 V to VIN2FINAL = VGEN3+0.8 V for
VGEN3[3:0] = 1000 to 1010
VGEN3LITR
–
5.0
mV
VIN2INITIAL = VGEN3+0.25 V to VIN2FINAL = 3.6 V for
VGEN3[3:0] = 1011 to 1111
Refer to Figure 31
Notes
63. When the LDO Output voltage is set above 2.6 V, the minimum allowed input voltage needs to be at least the output voltage plus 0.25 V,
for proper regulation due to the dropout voltage generated through the internal LDO transistor.
64. The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied
separately from the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to
operate in the dropout region of the regulator under test. VIN2MIN refers to the minimum allowed input voltage for a particular output
voltage.
PF0100
Analog Integrated Circuit Device Data
102
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
VGEN4
Table 105. VGEN4 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN2 = 3.6 V, VGEN4[3:0] = 1111, IGEN4 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN2 = 3.6 V,
VGEN4[3:0] = 1111, IGEN4 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN4
Operating Input Voltage
2.8
VGEN4NOM
0.250
1.8 V VGEN4NOM 2.5 V
VIN2
–
–
3.6
3.6
V
+
2.6 V VGEN4NOM 3.3 V(65)
Nominal Output Voltage
Operating Load Current
VGEN4 DC
VGEN4NOM
IGEN4
–
Table 93
–
–
V
0.0
350
mA
Output Voltage Tolerance
VIN2MIN < VIN2 < 3.6 V
VGEN4TOL
-3.0
–
–
3.0
–
%
0.0 mA < IGEN4 < 350 mA
VGEN4[3:0] = 0000 to 1111
Load Regulation
mV/
mA
(VGEN4 at IGEN4 = 350 mA) - (VGEN4 at IGEN4 = 0.0 mA )
For any VIN2MIN < VIN2 < 3.6 V
VGEN4LOR
0.07
Line Regulation
mV/
mA
(VGEN4 at 3.6 V) - (VGEN4 at VIN2MIN
For any 0.0 mA < IGEN4 < 350 mA
)
VGEN4LIR
IGEN4LIM
IGEN4OCP
–
0.80
584.5
–
–
Current Limit
GEN4 when VGEN4 is forced to VGEN4NOM/2
435
420
700
700
mA
mA
I
Over-current Protection Threshold
GEN4 required to cause the SCP function to disable LDO when
I
REGSCPEN = 1
Quiescent Current
No load, Change in IVIN and IVIN2
When VGEN4 enabled
IGEN4Q
–
13
–
A
VGEN4 AC AND TRANSIENT
PSRR(66)
•
IGEN4 = 262.5 mA, 20 Hz to 20 kHz
PSRRVGEN4
dB
35
55
40
60
–
–
VGEN4[3:0] = 0000 - 1110, VIN2 = VIN2MIN + 100 mV
VGEN4[3:0] = 0000 - 1000, VIN2 = VGEN4NOM + 1.0 V
Output Noise Density
IN2 = VIN2MIN, IGEN4 = 262.5 mA
•
V
dBV/
Hz
NOISEVGEN4
–
–
–
-114
-129
-135
-102
-123
-130
100 Hz – <1.0 kHz
1.0 kHz – <10 kHz
10 kHz – 1.0 MHz
Turn-On Slew Rate
•
10% to 90% of end value
•
VIN2MIN VIN2 3.6 V, IGEN4 = 0.0 mA
SLWRVGEN4
–
–
–
–
–
–
–
–
22.0
26.5
30.5
34.5
mVs
VGEN4[3:0] = 0000 to 0011
VGEN4[3:0] = 0100 to 0111
VGEN4[3:0] = 1000 to 1011
VGEN4[3:0] = 1100 to 1111
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
103
Functional Block Requirements and Behaviors
Power Generation
Table 105. VGEN4 Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN2 = 3.6 V, VGEN4[3:0] = 1111, IGEN4 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN2 = 3.6 V,
VGEN4[3:0] = 1111, IGEN4 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN4 AC AND TRANSIENT (CONTINUED)
Turn-On Time
Enable to 90% of end value, VIN2 = VIN2MIN, 3.6 V
GEN4tON
60
–
500
s
I
GEN4 = 0.0 mA
Turn-Off Time
Disable to 10% of initial value, VIN2 = VIN2MIN
IGEN4 = 0.0 mA
GEN4tOFF
GEN4OSHT
–
–
–
10
ms
%
Start-up Overshoot
1.0
2.0
V
IN2 = VIN2MIN, 3.6 V, IGEN4 = 0.0 mA
Transient Load Response
V
IN2 = VIN2MIN, 3.6 V
I
GEN4 = 35 to 350 mA in 1.0 s
VGEN4LOTR
–
–
3.0
8.0
%
Peak of overshoot or undershoot of VGEN4 with respect to final
value. Refer to Figure 31
Transient Line Response
I
GEN4 = 262.5 mA
VIN2INITIAL = 2.8 V to VIN2FINAL = 3.3 V for
VGEN4[3:0] = 0000 to 0111
VIN2INITIAL = VGEN4+0.3 V to VIN2FINAL = VGEN4+0.8 V for
VGEN4[3:0] = 1000 to 1010
VGEN4LITR
–
5.0
mV
VIN2INITIAL = VGEN4+0.25 V to VIN2FINAL = 3.6 V for
VGEN4[3:0] = 1011 to 1111
Refer to Figure 31
Notes
65. When the LDO Output voltage is set above 2.6 V the minimum allowed input voltage need to be at least the output voltage plus 0.25 V
for proper regulation due to the dropout voltage generated through the internal LDO transistor.
66. The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied
separately from the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to
operate in the dropout region of the regulator under test. VIN2MIN refers to the minimum allowed input voltage for a particular output
voltage.
PF0100
Analog Integrated Circuit Device Data
104
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
VGEN5
Table 106. VGEN5 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN3 = 3.6 V, VGEN5[3:0] = 1111, IGEN5 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN3 = 3.6 V,
VGEN5[3:0] = 1111, IGEN5 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN5
Operating Input Voltage
2.8
VGEN5NOM
0.250
–
–
4.5
4.5
1.8 V VGEN5NOM 2.5 V
VIN3
V
+
2.6 V VGEN5NOM 3.3 V(67)
Nominal Output Voltage
Operating Load Current
VGEN5 ACTIVE MODE – DC
VGEN5NOM
IGEN5
–
Table 93
–
–
V
0.0
100
mA
Output Voltage Tolerance
VIN3MIN < VIN3 < 4.5 V
VGEN5TOL
-3.0
–
–
3.0
–
%
0.0 mA < IGEN5 < 100 mA
VGEN5[3:0] = 0000 to 1111
Load Regulation
mV/
mA
(VGEN5 at IGEN5 = 100 mA) - (VGEN5 at IGEN5 = 0.0 mA)
For any VIN3MIN < VIN3 < 4.5 mV
VGEN5LOR
0.10
Line Regulation
mV/
mA
(VGEN5 at VIN3 = 4.5 V) - (VGEN5 at VIN3MIN
For any 0.0 mA < IGEN5 < 100 mA
)
VGEN5LIR
IGEN5LIM
IGEN5OCP
–
0.50
167
–
–
Current Limit
GEN5 when VGEN5 is forced to VGEN5NOM/2
122
120
200
200
mA
mA
I
Over-current Protection threshold
GEN5 required to cause the SCP function to disable LDO when
I
REGSCPEN = 1
Quiescent Current
No load, Change in IVIN and IVIN3
When VGEN5 enabled
IGEN5Q
–
13
–
A
VGEN5 AC AND TRANSIENT
PSRR(68)
•
IGEN5 = 75 mA, 20 Hz to 20 kHz
PSRRVGEN5
dB
35
52
40
60
–
–
VGEN5[3:0] = 0000 - 1111, VIN3 = VIN3MIN + 100 mV
VGEN5[3:0] = 0000 - 1111, VIN3 = VGEN5NOM + 1.0 V
Output Noise Density
IN3 = VIN3MIN, IGEN5 = 75 mA
•
V
dBV/
Hz
NOISEVGEN5
–
–
–
-114
-129
-135
-102
-123
-130
100 Hz – <1.0 kHz
1.0 kHz – <10 kHz
10 kHz – 1.0 MHz
Turn-On Slew Rate
•
10% to 90% of end value
•
VIN3MIN VIN3 4.5 mV, IGEN5 = 0.0 mA
SLWRVGEN5
–
–
–
–
–
–
–
–
22.0
26.5
30.5
34.5
mVs
VGEN5[3:0] = 0000 to 0011
VGEN5[3:0] = 0100 to 0111
VGEN5[3:0] = 1000 to 1011
VGEN5[3:0] = 1100 to 1111
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
105
Functional Block Requirements and Behaviors
Power Generation
Table 106. VGEN5 Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN3 = 3.6 V, VGEN5[3:0] = 1111, IGEN5 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN3 = 3.6 V,
VGEN5[3:0] = 1111, IGEN5 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN5 ACTIVE MODE – DC (CONTINUED)
Turn-On Time
Enable to 90% of end value, VIN3 = VIN3MIN, 4.5 V
GEN5tON
60
–
500
s
I
GEN5 = 0.0 mA
Turn-Off Time
Disable to 10% of initial value, VIN3 = VIN3MIN
IGEN5 = 0.0 mA
GEN5tOFF
GEN5OSHT
–
–
–
10
ms
%
Start-Up Overshoot
1.0
2.0
V
IN3 = VIN3MIN, 4.5 V, IGEN5 = 0.0 mA
Transient Load Response
V
IN3 = VIN3MIN, 4.5 V
I
GEN5 = 10 to 100 mA in 1.0 s
VGEN5LOTR
–
–
3.0
8.0
%
Peak of overshoot or undershoot of VGEN5 with respect to final
value.
Refer to Figure 31
Transient Line Response
IGEN5 = 75 mA
VIN3INITIAL = 2.8 V to VIN3FINAL = 3.3 V for
VGEN5[3:0] = 0000 to 0111
VGEN5LITR
-
5.0
mV
VIN3INITIAL = VGEN5+0.3 V to VIN3FINAL = VGEN5+0.8 V for
VGEN5[3:0] = 1000 to 1111
Refer to Figure 31
Notes
67. When the LDO Output voltage is set above 2.6 V the minimum allowed input voltage need to be at least the output voltage plus 0.25 V
for proper regulation due to the dropout voltage generated through the internal LDO transistor.
68. The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied
separately from the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to
operate in the dropout region of the regulator under test. VIN3MIN refers to the minimum allowed input voltage for a particular output
voltage.
PF0100
Analog Integrated Circuit Device Data
106
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
VGEN6
Table 107. VGEN6 Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN3 = 3.6 V, VGEN6[3:0] = 1111, IGEN6 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN3 = 3.6 V,
VGEN6[3:0] = 1111, IGEN6 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN6
Operating Input Voltage
2.8
VGEN6NOM
0.250
–
–
4.5
4.5
1.8 V VGEN6NOM 2.5 V
VIN3
+
V
2.6 V VGEN6NOM 3.3 V(69)
Nominal Output Voltage
Operating Load Current
VGEN6 DC
VGEN6NOM
IGEN6
–
Table 93
–
–
V
0.0
200
mA
Output Voltage Tolerance
VIN3MIN < VIN3 < 4.5 V
VGEN6TOL
-3.0
–
3.0
%
0.0 mA < IGEN6 < 200 mA
VGEN6[3:0] = 0000 to 1111
Load Regulation
mV/
mA
(VGEN6 at IGEN6 = 200 mA) - (VGEN6 at IGEN6 = 0.0 mA)
For any VIN3MIN < VIN3 < 4.5 V
VGEN6LOR
–
–
0.10
0.50
–
–
Line Regulation
mV/
mA
(VGEN6 at VIN3 = 4.5 V) - (VGEN6 at VIN3MIN
For any 0.0 mA < IGEN6 < 200 mA
)
VGEN6LIR
Current Limit
GEN6 when VGEN6 is forced to VGEN6NOM/2
I
IGEN6LIM
mA
MMPF0100
MMPF0100A
232
232
333
333
400
475
Over Current Protection Threshold
I
GEN6 required to cause the SCP function to disable LDO when
REGSCPEN = 1
MMPF0100
MMPF0100A
IGEN6OCP
mA
220
220
–
–
400
475
Quiescent Current
No load, Change in IVIN and IVIN3
When VGEN6 enabled
IGEN6Q
–
13
–
A
VGEN6 AC AND TRANSIENT
PSRR(70)
•
IGEN6 = 150 mA, 20 Hz to 20 kHz
PSRRVGEN6
dB
35
52
40
60
–
–
VGEN6[3:0] = 0000 - 1111, VIN3 = VIN3MIN + 100 mV
VGEN6[3:0] = 0000 - 1111, VIN3 = VGEN6NOM + 1.0 V
Output Noise Density
IN3 = VIN3MIN, IGEN6 = 150 mA
•
V
dBV/
Hz
NOISEVGEN6
–
–
–
-114
-129
-135
-102
-123
-130
100 Hz – <1.0 kHz
1.0 kHz – <10 kHz
10 kHz – 1.0 MHz
Turn-On Slew Rate
•
10% to 90% of end value
•
VIN3MIN VIN3 4.5 V. IGEN6 = 0.0 mA
SLWRVGEN6
–
–
–
–
–
–
–
–
22.0
26.5
30.5
34.5
mVs
VGEN6[3:0] = 0000 to 0011
VGEN6[3:0] = 0100 to 0111
VGEN6[3:0] = 1000 to 1011
VGEN6[3:0] = 1100 to 1111
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
107
Functional Block Requirements and Behaviors
Power Generation
Table 107. VGEN6 Electrical Characteristics (continued)
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VIN3 = 3.6 V, VGEN6[3:0] = 1111, IGEN6 = 10 mA, typical
external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN3 = 3.6 V,
VGEN6[3:0] = 1111, IGEN6 = 10 mA, and 25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VGEN6 AC AND TRANSIENT (CONTINUED)
Turn-On Time
Enable to 90% of end value, VIN3 = VIN3MIN, 4.5 V
GEN6tON
60
–
500
s
I
GEN6 = 0.0 mA
Turn-Off Time
Disable to 10% of initial value, VIN3 = VIN3MIN
GEN6tOFF
GEN6OSHT
–
–
–
10
ms
%
IGEN6 = 0.0 mA
Start-Up Overshoot
1.0
2.0
V
IN3 = VIN3MIN, 4.5 V, IGEN6 = 0 mA
Transient Load Response
VIN3 = VIN3MIN, 4.5 V
I
GEN6 = 20 to 200 mA in 1.0 s
VGEN6LOTR
–
–
–
3.0
8.0
%
Peak of overshoot or undershoot of VGEN6 with respect to final
value. Refer to Figure 31
Transient Line Response
IGEN6 = 150 mA
VIN3INITIAL = 2.8 V to VIN3FINAL = 3.3 V for
VGEN6[3:0] = 0000 to 0111
VGEN6LITR
5.0
mV
VIN3INITIAL = VGEN6+0.3 V to VIN3FINAL = VGEN6+0.8 V for
VGEN6[3:0] = 1000 to 1111
Refer to Figure 31
Notes
69. When the LDO Output voltage is set above 2.6 V the minimum allowed input voltage need to be at least the output voltage plus 0.25 V
for proper regulation due to the dropout voltage generated through the internal LDO transistor.
70. The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied
separately from the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to
operate in the dropout region of the regulator under test. VIN3MIN refers to the minimum allowed input voltage for a particular output
voltage.
6.4.7 VSNVS LDO/Switch
VSNVS powers the low power, SNVS/RTC domain on the processor. It derives its power from either VIN, or coin cell, and cannot
be disabled. When powered by both, VIN takes precedence when above the appropriate comparator threshold. When powered
by VIN, VSNVS is an LDO capable of supplying seven voltages: 3.0, 1.8, 1.5, 1.3, 1.2, 1.1, and 1.0 V. The bits VSNVSVOLT[2:0]
in register VSNVS_CONTROL determine the output voltage. When powered by coin cell, VSNVS is an LDO capable of supplying
1.8, 1.5, 1.3, 1.2, 1.1, or 1.0 V as shown in Table 108. If the 3.0 V option is chosen with the coin cell, VSNVS tracks the coin cell
voltage by means of a switch, whose maximum resistance is 100 . In this case, the VSNVS voltage is simply the coin cell
voltage minus the voltage drop across the switch, which is 40 mV at a rated maximum load current of 400 A.
The default setting of the VSNVSVOLT[2:0] is 110, or 3.0 V, unless programmed otherwise in OTP. However, when the coin cell
is applied for the very first time, VSNVS will output 1.0 V. Only when VIN is applied thereafter will VSNVS transition to its default,
or programmed value if different. Upon subsequent removal of VIN, with the coin cell attached, VSNVS will change configuration
from an LDO to a switch for the “110” setting, and will remain as an LDO for the other settings, continuing to output the same
voltages as when VIN is applied, providing certain conditions are met as described in Table 108.
PF0100
Analog Integrated Circuit Device Data
108
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
PF0100
VIN
2.25 V (VTL0) -
4.5 V
LDO/SWITCH
Input
LICELL
Charger
VREF
Sense/
Selector
_
+
VSNVS
Z
Coin Cell
1.8 - 3.3 V
I2C Interface
Figure 32. VSNVS Supply Switch Architecture
Table 108 provides a summary of the VSNVS operation at different input voltage VIN and with or without coin cell connected to
the system.
Table 108. VSNVS Modes of Operation
VSNVSVOLT[2:0]
110
VIN
MODE
> VTH1
< VTL1
> VTH0
< VTL0
VIN LDO 3.0 V
Coin cell switch
VIN LDO
110
000 – 101
000 – 101
Coin cell LDO
VSNVS Control
The VSNVS output level is configured through the VSNVSVOLT[2:0]bits on VSNVSCTL register as shown in table Table 109.
Table 109. Register VSNVSCTL - ADDR 0x6B
Name
Bit #
R/W Default
Description
Configures VSNVS output voltage.(71)
000 = 1.0 V
001 = 1.1 V
010 = 1.2 V
VSNVSVOLT
2:0
7:3
R/W
0x80
0x00
011 = 1.3 V
100 = 1.5 V
101 = 1.8 V
110 = 3.0 V
111 = RSVD
UNUSED
Notes
–
UNUSED
71. Only valid when a valid input voltage is present.
VSNVS External Components
Table 110. VSNVS External Components
Capacitor
Value (F)
VSNVS
0.47
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
109
Functional Block Requirements and Behaviors
Power Generation
VSNVS Specifications
Table 111. VSNVS Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VSNVS = 3.0 V, ISNVS = 5.0 A, typical external
component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VSNVS = 3.0 V, ISNVS = 5.0 A, and
25 °C, unless otherwise noted.
Parameter
Symbol
Min
Typ
Max
Unit
VSNVS
Operating Input Voltage
Valid Coin Cell range
Valid VIN
VINSNVS
1.8
2.25
–
–
3.3
4.5
V
Operating Load Current
VINMIN < VIN < VINMAX
ISNVS
5.0
–
400
A
VSNVS DC, LDO
Output Voltage
•
•
•
5.0 A < ISNVS < 400 A (OFF)
3.20 V < VIN < 4.5 V, VSNVSVOLT[2:0] = 110
VTL0/VTH < VIN < 4.5 V, VSNVSVOLT[2:0] = [000] - [101]
-5.0%
-8.0%
3.0
1.0 - 1.8
7.0%
7.0%
5.0A < ISNVS < 400A (ON)
3.20 V < VIN < 4.5 V, VSNVSVOLT[2:0] = 110
UVDET < VIN < 4.5 V, VSNVSVOLT[2:0] = [000] - [101]
VSNVS
V
-5.0%
-4.0%
3.0
1.0 - 1.8
5.0%
4.0%
50A < ISNVS < 400 A (Coin Cell mode)
V
COIN-0.04
-8.0%
–
VCOIN
7.0%
2.84 V < VCOIN < 3.3 V, VSNVSVOLT[2:0] = 110
1.8 V < VCOIN < 3.3 V, VSNVSVOLT[2:0] = [000] - [101](72)
1.0 - 1.8
Dropout Voltage
VSNVSDROP
–
–
50
mV
VIN = VCOIN = 2.85 V, VSNVSVOLT[2:0] = 110, ISNVS = 400 A
Current Limit
MMPF0100
V
V
V
IN > VTH1, VSNVSVOLT[2:0] = 110
IN > VTH0, VSNVSVOLT[2:0] = 000 to 101
IN < VTL0, VSNVSVOLT[2:0] = 000 to 101
750
500
480
–
–
–
5900
5900
3600
ISNVSLIM
A
MMPF0100A
V
V
V
IN > VTH1, VSNVSVOLT[2:0] = 110
IN > VTH0, VSNVSVOLT[2:0] = 000 to 101
IN < VTL0, VSNVSVOLT[2:0] = 000 to 101
1100
500
480
–
–
–
6750
6750
4500
VIN Threshold (Coin Cell Powered to VIN Powered) VIN going high
with valid coin cell
V
V
VSNVSVOLT[2:0] = 000, 001, 010, 011, 100, 101
VTH0
2.25
2.40
2.55
VIN Threshold (VIN Powered to Coin Cell Powered) VIN going low
with valid coin cell
VSNVSVOLT[2:0] = 000, 001, 010, 011, 100, 101
VTL0
2.20
5.0
2.35
–
2.50
–
VIN Threshold Hysteresis for VTH1-VTL1
VIN Threshold Hysteresis for VTH0-VTL0
VHYST1
VHYST0
mV
mV
5.0
–
–
Output Voltage During Crossover
VSNVSVOLT[2:0] = 110
VCOIN > 2.9 V
VSNVSCROSS
2.80
–
–
V
Switch to LDO: VIN > 2.825 V, ISNVS = 100 A
LDO to Switch: VIN < 3.05 V, ISNVS = 100 A
PF0100
Analog Integrated Circuit Device Data
110
Freescale Semiconductor
Functional Block Requirements and Behaviors
Power Generation
Table 111. VSNVS Electrical Characteristics
All parameters are specified at TMIN to TMAX (See Table 3), VIN = 3.6 V, VSNVS = 3.0 V, ISNVS = 5.0 A, typical external
component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VSNVS = 3.0 V, ISNVS = 5.0 A, and
25 °C, unless otherwise noted.
Parameter
VSNVS AC AND TRANSIENT
Symbol
Min
Typ
Max
Unit
Turn-on Time(73),(74) (Load capacitor, 0.47 F)
VIN > UVDET to 90% of VSNVS
VCOIN = 0.0 V, ISNVS = 5.0 A
VSNVSVOLT[2:0] = 000 to 110
tONSNVS
–
–
–
24
70
ms
Start-up Overshoot
VSNVSVOLT[2:0] = 000 to 110
VSNVSOSH
40
mV
mV
V
ISNVS = 5.0 A
dVIN/dt = 50 mV/s
Transient Line Response ISNVS = 75% of ISNVSMAX
3.2 V < VIN < 4.5 V, VSNVSVOLT[2:0] = 110
–
–
32
22
–
–
VSNVSLITR
2.45 V < VIN < 4.5 V, VSNVSVOLT[2:0] = [000] - [101]
Transient Load Response
VSNVSVOLT[2:0] = 110
3.1 V (UVDETL)< VIN 4.5 V
2.8
–
–
–
ISNVS = 75 to 750 A
VSNVSVOLT[2:0] = 000 to 101
2.45 V < VIN 4.5 V
VTL0 > VIN, 1.8 V VCOIN 3.3 V
VSNVSLOTR
1.0
2.0
%
ISNVS = 40 to 400 A
Refer to Figure 31
VSNVS DC, SWITCH
Operating Input voltage
Valid Coin Cell range
VINSNVS
ISNVS
1.8
5.0
–
–
–
–
3.3
400
100
V
A
Operating Load Current
Internal Switch Rdson
RDSONSNVS
VCOIN = 2.6 V
VIN Threshold (VIN Powered to Coin Cell Powered)
VSNVSVOLT[2:0] = 110
VTL1
VTH1
2.825
2.85
2.90
2.95
3.00
3.1
V
V
VIN Threshold (Coin Cell Powered to VIN Powered)
VSNVSVOLT[2:0] = 110
Notes
72. For 1.8 V ISNVS limited to 100 A for VCOIN < 2.1 V
73. The start-up of VSNVS is not monotonic. It first rises to 1.0 V and then settles to its programmed value within the specified tr1 time.
74. From coin cell insertion to VSNVS =1.0 V, the delay time is typically 400 ms.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
111
Functional Block Requirements and Behaviors
Power Generation
6.4.7.1
Coin Cell Battery Backup
The LICELL pin provides for a connection of a coin cell backup battery or a “super” capacitor. If the voltage at VIN goes below
the VIN threshold (VTL1 and VTL0), contact-bounced, or removed, the coin cell maintained logic will be powered by the voltage
applied to LICELL. The supply for internal logic and the VSNVS rail will switch over to the LICELL pin when VIN goes below VTL1
or VTL0, even in the absence of a voltage at the LICELL pin, resulting in clearing of memory and turning off of VSNVS. When
system operation below VTL1 is required, for systems not utilizing a coin cell, connect the LICELL pin to any system voltage
between 1.8 and 3.0 V.
A small capacitor should be placed from LICELL to ground under all circumstances.
Coin Cell Charger Control
The coin cell charger circuit will function as a current-limited voltage source, resulting in the CC/CV taper characteristic typically
used for rechargeable Lithium-Ion batteries. The coin cell charger is enabled via the COINCHEN bit while the coin cell voltage is
programmable through the VCOIN[2:0] bits on register COINCTL on Table 113. The coin cell charger voltage is programmable.
In the ON state, the charger current is fixed at ICOINHI. In Sleep and Standby modes, the charger current is reduced to a typical
10 A. In the OFF state, coin cell charging is not available as the main battery could be depleted unnecessarily. The coin cell
charging will be stopped when VIN is below UVDET.
Table 112. Coin Cell Charger Voltage
VCOIN[2:0]
VCOIN (V)(75)
000
001
010
011
100
101
110
111
2.50
2.70
2.80
2.90
3.00
3.10
3.20
3.30
Notes
75. Coin cell voltages selected based on the
type of LICELL used on the system.
Table 113. Register COINCTL - ADDR 0x1A
Name
Bit #
R/W Default
Description
Coin cell charger output voltage selection.
See Table 112 for all options selectable through
these bits.
VCOIN
2:0
R/W
0x00
COINCHEN
UNUSED
3
R/W
–
0x00
0x00
Enable or disable the Coin cell charger
UNUSED
7:4
External Components
Table 114. Coin Cell Charger External Components
Component
Value
Units
LICELL Bypass Capacitor
100
nF
PF0100
Analog Integrated Circuit Device Data
112
Freescale Semiconductor
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Coin Cell Specifications
Table 115. Coin Cell Charger Specifications
Parameter
Typ
Unit
Voltage Accuracy
100
60
mV
A
%
Coin Cell Charge Current in On mode ICOINHI
Current Accuracy
30
2
6.5
Control Interface I C Block Description
The PF0100 contains an I2C interface port which allows access by a processor, or any I2C master, to the register set. Via these
registers the resources of the IC can be controlled. The registers also provide status information about how the IC is operating.
The SCL and SDA lines should be routed away from noisy signals and planes to minimize noise pick up. To prevent reflections
in the SCL and SDA traces from creating false pulses, the rise and fall times of the SCL and SDA signals must be greater than
20 ns. This can be accomplished by reducing the drive strength of the I2C master via software. The i.MX6 I2C driver defaults to
a 40 ohm drive strength. It is recommended to use a drive strength of 80 ohm or higher to increase the edge times. Alternatively,
this can be accomplished by using small capacitors from SCL and SDA to ground. For example, use 5.1 pF capacitors from SCL
and SDA to ground for bus pull-up resistors of 4.8 kohm.
2
6.5.1 I C Device ID
I2C interface protocol requires a device ID for addressing the target IC on a multi-device bus. To allow flexibility in addressing for
bus conflict avoidance, fuse programmability is provided to allow configuration for the lower 3 address LSB(s). Refer to One Time
Programmability (OTP) for more details. This product supports 7-bit addressing only; support is not provided for 10-bit or general
call addressing. Note, when the TBB bits for the I2C slave address are written, the next access to the chip, must then use the
new slave address; these bits take affect right away.
6.5.2 I2C Operation
The I2C mode of the interface is implemented generally following the Fast mode definition which supports up to 400 kbits/s
operation (exceptions to the standard are noted to be 7-bit only addressing and no support for General Call addressing.) Timing
diagrams, electrical specifications, and further details can be found in the I2C specification, which is available for download at:
http://www.nxp.com/acrobat_download/literature/9398/39340011.pdf
I2C read operations are also performed in byte increments separated by an ACK. Read operations also begin with the MSB and
each byte will be sent out unless a STOP command or NACK is received prior to completion.
The following examples show how to write and read data to and from the IC. The host initiates and terminates all communication.
The host sends a master command packet after driving the start condition. The device will respond to the host if the master
command packet contains the corresponding slave address. In the following examples, the device is shown always responding
with an ACK to transmissions from the host. If at any time a NACK is received, the host should terminate the current transaction
and retry the transaction.
Host can
also drive
another
Start instead
Packet
Type
Device
Master Driven Data
byte 0 )
Register Address
Address
(
of Stop
7
0
7
0
0
7
0
START
STOP
Host SDA
R / W
A
C
K
A
C
K
A
C
K
Slave SDA
Figure 33. I2C Write Example
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
113
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Host can also
drive another
Start instead of
Stop
Packet
Type
Device
Address
Register Address
Device Address
PMIC Driven Data
23
16
0
15
8
7
0
NA
CK
START
START
1
STOP
Host SDA
R/W
R/W
7
0
A
C
K
A
C
K
A
C
K
Slave SDA
Figure 34. I2C Read Example
6.5.3 Interrupt Handling
The system is informed about important events based on interrupts. Unmasked interrupt events are signaled to the processor by
driving the INTB pin low.
Each interrupt is latched so that even if the interrupt source becomes inactive, the interrupt will remain set until cleared. Each
interrupt can be cleared by writing a “1” to the appropriate bit in the Interrupt Status register; this will also cause the INTB pin to
go high. If there are multiple interrupt bits set the INTB pin will remain low until all are either masked or cleared. If a new interrupt
occurs while the processor clears an existing interrupt bit, the INTB pin will remain low.
Each interrupt can be masked by setting the corresponding mask bit to a 1. As a result, when a masked interrupt bit goes high,
the INTB pin will not go low. A masked interrupt can still be read from the Interrupt Status register. This gives the processor the
option of polling for status from the IC. The IC powers up with all interrupts masked, so the processor must initially poll the device
to determine if any interrupts are active. Alternatively, the processor can unmask the interrupt bits of interest. If a masked interrupt
bit was already high, the INTB pin will go low after unmasking.
The sense registers contain status and input sense bits so the system processor can poll the current state of interrupt sources.
They are read only, and not latched or clearable.
Interrupts generated by external events are debounced; therefore, the event needs to be stable throughout the debounce period
before an interrupt is generated. Nominal debounce periods for each event are documented in the INT summary Table 116 . Due
to the asynchronous nature of the debounce timer, the effective debounce time can vary slightly.
6.5.4 Interrupt Bit Summary
Table 116 summarizes all interrupt, mask, and sense bits associated with INTB control. For more detailed behavioral
descriptions, refer to the related chapters.
Table 116. Interrupt, Mask and Sense Bits
Interrupt
LOWVINI
Mask
LOWVINM
Sense
LOWVINS
Purpose
Trigger
Debounce Time (ms)
Low Input Voltage Detect
Sense is 1 if below 2.80 V threshold
H to L
3.9(76)
Power on button event
H to L
L to H
31.25(76)
31.25
PWRONI
PWRONM
PWRONS
Sense is 1 if PWRON is high.
Thermal 110 °C threshold
Sense is 1 if above threshold
THERM110
THERM120
THERM125
THERM130
SW1AFAULTI
SW1BFAULTI
THERM110M
THERM120M
THERM125M
THERM130M
SW1AFAULTM
SW1BFAULTM
THERM110S
THERM120S
THERM125S
THERM130S
SW1AFAULTS
SW1BFAULTS
Dual
Dual
3.9
3.9
3.9
3.9
8.0
8.0
Thermal 120 °C threshold
Sense is 1 if above threshold
Thermal 125 °C threshold
Sense is 1 if above threshold
Dual
Thermal 130 °C threshold
Sense is 1 if above threshold
Dual
Regulator 1A over-current limit
Sense is 1 if above current limit
L to H
L to H
Regulator 1B over-current limit
Sense is 1 if above current limit
PF0100
Analog Integrated Circuit Device Data
114
Freescale Semiconductor
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 116. Interrupt, Mask and Sense Bits (continued)
Interrupt
Mask
Sense
Purpose
Trigger
Debounce Time (ms)
Regulator 1C over-current limit
Sense is 1 if above current limit
SW1CFAULTI
SW1CFAULTM
SW1CFAULTS
L to H
8.0
Regulator 2 over-current limit
Sense is 1 if above current limit
SW2FAULTI
SW2FAULTM
SW2FAULTS
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Regulator 3A over-current limit
Sense is 1 if above current limit
SW3AFAULTI
SW3BFAULTI
SW4FAULTI
SW3AFAULTM
SW3BFAULTM
SW4FAULTM
SW3AFAULTS
SW3BFAULTS
SW4FAULTS
Regulator 3B over-current limit
Sense is 1 if above current limit
Regulator 4 over-current limit
Sense is 1 if above current limit
SWBST over-current limit
Sense is 1 if above current limit
SWBSTFAULTI
VGEN1FAULTI
VGEN2FAULTI
VGEN3FAULTI
VGEN4FAULTI
VGEN5FAULTI
VGEN6FAULTI
SWBSTFAULTM
VGEN1FAULTM
VGEN2FAULTM
VGEN3FAULTM
VGEN4FAULTM
VGEN5FAULTM
VGEN6FAULTM
OTP_ECCM
SWBSTFAULTS
VGEN1FAULTS
VGEN2FAULTS
VGEN3FAULTS
VGEN4FAULTS
VGEN1FAULTS
VGEN6FAULTS
OTP_ECCS
VGEN1 over-current limit
Sense is 1 if above current limit
VGEN2 over-current limit
Sense is 1 if above current limit
VGEN3 over-current limit
Sense is 1 if above current limit
VGEN4 over-current limit
Sense is 1 if above current limit
VGEN5 over-current limit
Sense is 1 if above current limit
VGEN6 over-current limit
Sense is 1 if above current limit
1 or 2 bit error detected in OTP registers
Sense is 1 if error detected
OTP_ECCI
Notes
76. Debounce timing for the falling edge can be extended with PWRONDBNC[1:0].
A full description of all interrupt, mask, and sense registers is provided in Tables 117 to 128.
Table 117. Register INTSTAT0 - ADDR 0x05
Name
PWRONI
Bit #
R/W
Default
Description
Power on interrupt bit
0
1
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
–
0
0
LOWVINI
Low-voltage interrupt bit
110 °C Thermal interrupt bit
120 °C Thermal interrupt bit
125 °C Thermal interrupt bit
130 °C Thermal interrupt bit
Unused
THERM110I
THERM120I
THERM125I
THERM130I
UNUSED
2
0
3
0
4
0
5
0
7:6
00
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
115
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 118. Register INTMASK0 - ADDR 0x06
Name
PWRONM
Bit #
R/W
Default
Description
0
1
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
–
1
1
Power on interrupt mask bit
Low-voltage interrupt mask bit
110 °C Thermal interrupt mask bit
120 °C Thermal interrupt mask bit
125 °C Thermal interrupt mask bit
130 °C Thermal interrupt mask bit
Unused
LOWVINM
THERM110M
THERM120M
THERM125M
THERM130M
UNUSED
2
1
3
1
4
1
5
1
7:6
00
Table 119. Register INTSENSE0 - ADDR 0x07
Name
Bit #
R/W
Default
Description
Power on sense bit
0 = PWRON low
1 = PWRON high
PWRONS
0
R
0
Low voltage sense bit
0 = VIN > 2.8 V
LOWVINS
1
2
3
4
R
R
R
R
0
0
0
0
1 = VIN 2.8 V
110 °C Thermal sense bit
0 = Below threshold
1 = Above threshold
THERM110S
THERM120S
THERM125S
120 °C Thermal sense bit
0 = Below threshold
1 = Above threshold
125 °C Thermal sense bit
0 = Below threshold
1 = Above threshold
130 °C Thermal sense bit
0 = Below threshold
1 = Above threshold
THERM130S
UNUSED
5
6
7
R
–
0
0
Unused
Additional VDDOTP voltage sense pin
0 = VDDOTP grounded
VDDOTPS
R
00
1 = VDDOTP to VCOREDIG or greater
Table 120. Register INTSTAT1 - ADDR 0x08
Name
Bit #
R/W
Default
Description
SW1AFAULTI
SW1BFAULTI
SW1CFAULTI
SW2FAULTI
SW3AFAULTI
SW3BFAULTI
SW4FAULTI
UNUSED
0
1
2
3
4
5
6
7
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
–
0
0
0
0
0
0
0
0
SW1A Over-current interrupt bit
SW1B Over-current interrupt bit
SW1C Over-current interrupt bit
SW2 Over-current interrupt bit
SW3A Over-current interrupt bit
SW3B Over-current interrupt bit
SW4 Over-current interrupt bit
Unused
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
116
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 121. Register INTMASK1 - ADDR 0x09
Name
Bit #
R/W
Default
Description
SW1AFAULTM
SW1BFAULTM
SW1CFAULTM
SW2FAULTM
SW3AFAULTM
SW3BFAULTM
SW4FAULTM
UNUSED
0
1
2
3
4
5
6
7
R/W
R/W
R/W
R/W
R/W
R/W
R/W
–
1
1
1
1
1
1
1
0
SW1A Over-current interrupt mask bit
SW1B Over-current interrupt mask bit
SW1C Over-current interrupt mask bit
SW2 Over-current interrupt mask bit
SW3A Over-current interrupt mask bit
SW3B Over-current interrupt mask bit
SW4 Over-current interrupt mask bit
Unused
Table 122. Register INTSENSE1 - ADDR 0x0A
Name
Bit #
R/W
Default
Description
SW1A Over-current sense bit
0 = Normal operation
SW1AFAULTS
0
R
0
1 = Above current limit
SW1B Over-current sense bit
0 = Normal operation
SW1BFAULTS
SW1CFAULTS
SW2FAULTS
SW3AFAULTS
SW3BFAULTS
1
2
3
4
5
R
R
R
R
R
0
0
0
0
0
1 = Above current limit
SW1C Over-current sense bit
0 = Normal operation
1 = Above current limit
SW2 Over-current sense bit
0 = Normal operation
1 = Above current limit
SW3A Over-current sense bit
0 = Normal operation
1 = Above current limit
SW3B Over-current sense bit
0 = Normal operation
1 = Above current limit
SW4 Over-current sense bit
0 = Normal operation
SW4FAULTS
UNUSED
6
7
R
–
0
0
1 = Above current limit
Unused
Table 123. Register INTSTAT3 - ADDR 0x0E
Name
Bit #
R/W
Default
Description
SWBSTFAULTI
UNUSED
0
6:1
7
R/W1C
–
0
0x00
0
SWBST over-current limit interrupt bit
Unused
OTP_ECCI
R/W1C
OTP error interrupt bit
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
117
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 124. Register INTMASK3 - ADDR 0x0F
Name
Bit #
R/W
Default
Description
SWBSTFAULTM
UNUSED
0
6:1
7
R/W
–
1
0x00
1
SWBST over-current limit interrupt mask bit
Unused
OTP_ECCM
R/W
OTP error interrupt mask bit
Table 125. Register INTSENSE3 - ADDR 0x10
Name
Bit #
R/W
Default
Description
SWBST over-current limit sense bit
0 = Normal operation
SWBSTFAULTS
UNUSED
0
6:1
7
R
–
0
0x00
0
1 = Above current limit
Unused
OTP error sense bit
0 = No error detected
1 = OTP error detected
OTP_ECCS
R
Table 126. Register INTSTAT4 - ADDR 0x11
Name
Bit #
R/W
Default
Description
VGEN1FAULTI
VGEN2FAULTI
VGEN3FAULTI
VGEN4FAULTI
VGEN5FAULTI
VGEN6FAULTI
UNUSED
0
1
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
R/W1C
–
0
0
VGEN1 Over-current interrupt bit
VGEN2 Over-current interrupt bit
VGEN3 Over-current interrupt bit
VGEN4 Over-current interrupt bit
VGEN5 Over-current interrupt bit
VGEN6 Over-current interrupt bit
Unused
2
0
3
0
4
0
5
0
7:6
00
Table 127. Register INTMASK4 - ADDR 0x12
Name
Bit #
R/W
Default
Description
VGEN1FAULTM
VGEN2FAULTM
VGEN3FAULTM
VGEN4FAULTM
VGEN5FAULTM
VGEN6FAULTM
UNUSED
0
1
R/W
R/W
R/W
R/W
R/W
R/W
–
1
1
VGEN1 Over-current interrupt mask bit
VGEN2 Over-current interrupt mask bit
VGEN3 Over-current interrupt mask bit
VGEN4 Over-current interrupt mask bit
VGEN5 Over-current interrupt mask bit
VGEN6 Over-current interrupt mask bit
Unused
2
1
3
1
4
1
5
1
7:6
00
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
118
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 128. Register INTSENSE4 - ADDR 0x13
Name
Bit #
R/W
Default
Description
VGEN1 Over-current sense bit
VGEN1FAULTS
0
R
0
0 = Normal operation
1 = Above current limit
VGEN2 Over-current sense bit
0 = Normal operation
VGEN2FAULTS
VGEN3FAULTS
VGEN4FAULTS
VGEN5FAULTS
1
2
3
4
R
R
R
R
0
0
0
0
1 = Above current limit
VGEN3 Over-current sense bit
0 = Normal operation
1 = Above current limit
VGEN4 Over-current sense bit
0 = Normal operation
1 = Above current limit
VGEN5 Over-current sense bit
0 = Normal operation
1 = Above current limit
VGEN6 Over-current sense bit
0 = Normal operation
VGEN6FAULTS
UNUSED
5
R
–
0
1 = Above current limit
7:6
00
Unused
6.5.5 Specific Registers
6.5.5.1
IC and Version Identification
The IC and other version details can be read via identification bits. These are hard-wired on chip and described in Tables 129 to
131.
Table 129. Register DEVICEID - ADDR 0x00
Name
DEVICEID
UNUSED
Bit #
R/W
Default
Description
Die version.
0000 = PF0100
3:0
7:4
R
–
0x00
0x01
Unused
Table 130. Register SILICON REV- ADDR 0x03
Name
Bit #
R/W
Default
Description
Represents the metal mask revision
Pass 0.0 = 0000
METAL_LAYER_REV
3:0
R
0x00
.
.
Pass 0.15 = 1111
Represents the full mask revision
Pass 1.0 = 0001
FULL_LAYER_REV
7:4
R
0x01
.
.
Pass 15.0 = 1111
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
119
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 131. Register FABID - ADDR 0x04
Name
Bit #
R/W
Default
Description
Allows for characterizing different options within
the same reticule
FIN
1:0
R
0x00
FAB
3:2
7:0
R
R
0x00
0x00
Represents the wafer manufacturing facility
Unused
Unused
6.5.5.2
Embedded Memory
There are four register banks of general purpose embedded memory to store critical data. The data written to MEMA[7:0],
MEMB[7:0], MEMC[7:0], and MEMD[7:0] is maintained by the coin cell when the main battery is deeply discharged, removed, or
contact-bounced. The contents of the embedded memory are reset by COINPORB. The banks can be used for any system need
for bit retention with coin cell backup.
Table 132. Register MEMA ADDR 0x1C
Name
Bit #
R/W
Default
Description
Description
Description
Description
MEMA
7:0
R/W
0
Memory bank A
Memory bank B
Memory bank C
Memory bank D
Table 133. Register MEMB ADDR 0x1D
Name
Bit #
R/W
Default
MEMB
7:0
R/W
0
Table 134. Register MEMC ADDR 0x1E
Name
Bit #
R/W
Default
MEMC
7:0
R/W
0
Table 135. Register MEMD ADDR 0x1F
Name
Bit #
R/W
Default
MEMD
7:0
R/W
0
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
120
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
6.5.6 Register Bitmap
The register map is comprised of thirty-two pages, and its address and data fields are each eight bits wide. Only the first two
pages can be accessed. On each page, registers 0 to 0x7F are referred to as 'functional', and registers 0x80 to 0xFF as
'extended'. On each page, the functional registers are the same, but the extended registers are different. To access registers on
Extended Page 1, one must first write 0x01 to the page register at address 0x7F, and to access registers Extended Page 2, one
must first write 0x02 to the page register at address 0x7F. To access the Functional Page from one of the extended pages, no
write to the page register is necessary.
Registers that are missing in the sequence are reserved; reading from them will return a value 0x00, and writing to them will have
no effect.
The contents of all registers are given in the tables defined in this chapter; each table is structure as follows:
Name: Name of the bit.
Bit #: The bit location in the register (7-0)
R/W: Read / Write access and control
• R is read-only access
• R/W is read and write access
• RW1C is read and write access with write 1 to clear
Reset: Reset signals are color coded based on the following legend.
Bits reset by SC and VCOREDIG_PORB
Bits reset by PWRON or loaded default or OTP configuration
Bits reset by DIGRESETB
Bits reset by PORB or RESETBMCU
Bits reset by VCOREDIG_PORB
Bits reset by POR or OFFB
Default: The value after reset, as noted in the Default column of the memory map.
• Fixed defaults are explicitly declared as 0 or 1.
• “X” corresponds to Read / Write bits that are initialized at start-up, based on the OTP fuse settings or default if
VDDOTP = 1.5 V. Bits are subsequently I2C modifiable, when their reset has been released. “X” may also refer to bits that
may have other dependencies. For example, some bits may depend on the version of the IC, or a value from an analog
block, for instance the sense bits for the interrupts.
6.5.6.1
Register map
Table 136. Functional Page
BITS[7:0]
Register
Name
Add
R/W
Default
7
6
5
4
3
2
1
0
–
0
–
0
–
0
–
1
DEVICE ID [3:0]
0
00
DeviceID
R
8'b0001_0000
0
0
0
FULL_LAYER_REV[3:0]
METAL_LAYER_REV[3:0]
03
04
05
SILICONREVID
FABID
R
R
8'b0001_0000
8'b0000_0000
X
–
0
–
0
X
–
0
–
0
X
X
–
0
X
0
X
X
X
–
FAB[1:0]
FIN[1:0]
0
0
0
LOWVINI
0
0
PWRONI
0
THERM130I
0
THERM125I
0
THERM120I
0
THERM110I
0
INTSTAT0
RW1C 8'b0000_0000
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
121
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 136. Functional Page (continued)
BITS[7:0]
Register
Name
Add
R/W
Default
7
6
5
4
3
2
1
0
–
–
THERM130M
THERM125M THERM120M THERM110M
LOWVINM
PWRONM
06
INTMASK0
R/W 8'b0011_1111
0
0
1
1
1
1
1
1
VDDOTPS
RSVD
THERM130S
x
THERM125S
x
THERM120S
THERM110S
x
LOWVINS
x
PWRONS
07
08
09
0A
INTSENSE0
INTSTAT1
R
8'b00xx_xxxx
0
–
0
–
0
–
0
0
x
x
SW4FAULTI
0
SW3BFAULTI SW3AFAULTI
SW2FAULTI
0
SW1CFAULTI SW1BFAULTI
SW1AFAULTI
0
RW1C 8'b0000_0000
R/W 8'b0111_1111
0
0
0
0
SW4FAULTM SW3BFAULTM SW3AFAULTM SW2FAULTM SW1CFAULTM SW1BFAULTM SW1AFAULTM
INTMASK1
INTSENSE1
1
1
1
1
1
1
1
SW4FAULTS SW3BFAULTS SW3AFAULTS SW2FAULTS SW1CFAULTS SW1BFAULTS SW1AFAULTS
R
8'b0xxx_xxxx
x
x
x
x
x
x
x
OTP_ECCI
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
SWBSTFAULTI
0E
0F
10
11
INTSTAT3
INTMASK3
INTSENSE3
INTSTAT4
RW1C 8'b0000_0000
R/W 8'b1000_0001
0
0
OTP_ECCM
SWBSTFAULTM
1
1
OTP_ECCS
SWBSTFAULTS
x
R
8'b0000_000x
0
–
0
VGEN6FAULTI VGEN5FAULTI VGEN4FAULTI VGEN3FAULTI VGEN2FAULTI VGEN1FAULTI
RW1C 8'b0000_0000
R/W 8'b0011_1111
0
0
0
0
0
0
VGEN6
FAULTM
VGEN5
FAULTM
VGEN4
FAULTM
VGEN3
FAULTM
VGEN2
FAULTM
VGEN1
FAULTM
–
0
–
0
–
0
–
0
12
13
INTMASK4
1
1
1
1
1
1
VGEN6
FAULTS
VGEN5
FAULTS
VGEN4
FAULTS
VGEN3
FAULTS
VGEN2
FAULTS
VGEN1
FAULTS
INTSENSE4
R
8'b00xx_xxxx
x
x
x
x
x
x
–
0
–
0
–
0
–
0
COINCHEN
0
VCOIN[2:0]
0
1A
1B
1C
1D
1E
1F
COINCTL
PWRCTL
MEMA
R/W 8'b0000_0000
R/W 8'b0001_0000
R/W 8'b0000_0000
R/W 8'b0000_0000
R/W 8'b0000_0000
R/W 8'b0000_0000
0
0
0
0
0
0
0
REGSCPEN STANDBYINV
STBYDLY[1:0]
PWRONBDBNC[1:0]
PWRONRSTEN RESTARTEN
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MEMA[7:0]
MEMB[7:0]
MEMC[7:0]
MEMD[7:0]
MEMB
MEMC
MEMD
PF0100
Analog Integrated Circuit Device Data
122
Freescale Semiconductor
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 136. Functional Page (continued)
BITS[7:0]
Register
Name
Add
R/W
Default
7
6
5
4
3
2
1
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
SW1AB[5:0]
20
SW1ABVOLT R/W/M 8'b00xx_xxxx
x
x
x
x
x
x
x
x
x
x
x
SW1ABSTBY[5:0]
21
22
23
24
SW1ABSTBY
SW1ABOFF
R/W 8'b00xx_xxxx
R/W 8'b00xx_xxxx
R/W 8'b0000_1000
R/W 8'bxx00_xx00
x
x
SW1ABOFF[5:0]
x
x
x
–
0
x
x
SW1ABOMODE
0
SW1ABMODE[3:0]
SW1ABMODE
SW1ABCONF
1
0
0
–
0
SW1ABDVSSPEED[1:0]
SW1BAPHASE[1:0]
SW1ABFREQ[1:0]
SW1ABILIM
0
x
x
0
0
x
x
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
SW1C[5:0]
2E
2F
30
31
32
SW1CVOLT
SW1CSTBY
SW1COFF
R/W 8'b00xx_xxxx
R/W 8'b00xx_xxxx
R/W 8'b00xx_xxxx
R/W 8'b0000_1000
R/W 8'bxx00_xx00
x
x
x
x
x
x
x
1
x
x
x
x
x
x
SW1CSTBY[5:0]
x
SW1COFF[5:0]
x
x
x
–
0
x
SW1COMODE
0
SW1CMODE[3:0]
SW1CMODE
SW1CCONF
0
0
–
0
0
SW1CILIM
0
SW1CDVSSPEED[1:0]
SW1CPHASE[1:0]
SW1CFREQ[1:0]
x
x
0
0
x
x
–
0
–
0
–
0
–
0
SW2[6:0]
35
36
37
38
39
SW2VOLT
SW2STBY
SW2OFF
R/W
R/W
R/W
8'b0xxx_xxxx
8'b0xxx_xxxx
8'b0xxx_xxxx
x
x
x
x
x
x
x
x
x
x
0
x
x
x
x
x
x
SW2STBY[6:0]
x
SW2OFF[6:0]
x
x
–
0
x
x
–
0
x
SW2OMODE
0
SW2MODE[3:0]
SW2MODE
SW2CONF
R/W 8'b0000_1000
R/W 8'bxx01_xx00
1
0
–
0
0
SW2ILIM
0
SW2DVSSPEED[1:0]
SW2PHASE[1:0]
SW2FREQ[1:0]
x
x
0
1
x
–
0
–
0
SW3A[6:0]
3C
3D
SW3AVOLT
SW3ASTBY
R/W
R/W
8'b0xxx_xxxx
8'b0xxx_xxxx
x
x
x
x
x
x
x
x
x
x
x
x
x
SW3ASTBY[6:0]
x
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
123
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 136. Functional Page (continued)
BITS[7:0]
Register
Name
Add
R/W
Default
7
6
5
4
3
2
1
0
–
0
SW3AOFF[6:0]
x
3E
SW3AOFF
R/W
8'b0xxx_xxxx
x
x
x
–
0
x
x
x
SW3AOMODE
0
SW3AMODE[3:0]
3F
40
SW3AMODE
SW3ACONF
R/W 8'b0000_1000
R/W 8'bxx10_xx00
0
0
1
x
0
0
–
0
0
SW3AILIM
0
SW3ADVSSPEED[1:0]
SW3APHASE[1:0]
SW3AFREQ[1:0]
x
x
1
0
x
–
0
–
0
–
0
–
0
SW3B[6:0]
43
44
45
46
47
SW3BVOLT
SW3BSTBY
SW3BOFF
R/W
R/W
R/W
8'b0xxx_xxxx
8'b0xxx_xxxx
8'b0xxx_xxxx
x
x
x
x
x
x
x
x
x
x
0
x
x
x
x
x
x
SW3BSTBY[6:0]
x
SW3BOFF[6:0]
x
x
–
0
x
x
–
0
x
SW3BOMODE
0
SW3BMODE[3:0]
SW3BMODE
SW3BCONF
R/W 8'b0000_1000
R/W 8'bxx10_xx00
1
0
–
0
0
SW3BILIM
0
SW3BDVSSPEED[1:0]
SW3BPHASE[1:0]
SW3BFREQ[1:0]
x
x
1
0
x
–
0
–
0
–
0
–
0
SW4[6:0]
4A
4B
4C
4D
4E
SW4VOLT
SW4STBY
SW4OFF
R/W
R/W
R/W
8'b0xxx_xxxx
8'b0xxx_xxxx
8'b0xxx_xxxx
x
x
x
x
x
x
x
x
x
x
0
x
x
x
x
x
x
SW4STBY[6:0]
x
SW4OFF[6:0]
x
x
–
0
x
x
–
0
x
SW4OMODE
0
SW4MODE[3:0]
SW4MODE
SW4CONF
R/W 8'b0000_1000
R/W 8'bxx11_xx00
1
0
–
0
0
SW4ILIM
0
SW4DVSSPEED[1:0]
SW4PHASE[1:0]
SW4FREQ[1:0]
x
x
1
1
x
–
0
SWBST1STBYMODE[1:0]
–
0
SWBST1MODE[1:0]
SWBST1VOLT[1:0]
66
SWBSTCTL
R/W 8'b0xx0_10xx
x
x
1
0
x
x
–
0
–
0
–
0
–
0
–
0
–
0
VREFDDREN
–
0
–
0
–
0
–
–
0
6A
6B
VREFDDRCTL
VSNVSCTL
R/W 8'b000x_0000
R/W 8'b0000_0xxx
x
–
0
0
VSNVSVOLT[2:0]
x
0
x
PF0100
Analog Integrated Circuit Device Data
124
Freescale Semiconductor
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 136. Functional Page (continued)
BITS[7:0]
Register
Name
Add
R/W
Default
7
6
5
4
3
2
1
0
–
0
–
0
–
0
–
0
–
0
–
0
VGEN1LPWR VGEN1STBY
VGEN1EN
VGEN1[3:0]
VGEN2[3:0]
VGEN3[3:0]
VGEN4[3:0]
VGEN5[3:0]
VGEN6[3:0]
6C
VGEN1CTL
R/W 8'b000x_xxxx
R/W 8'b000x_xxxx
R/W 8'b000x_xxxx
R/W 8'b000x_xxxx
R/W 8'b000x_xxxx
R/W 8'b000x_xxxx
0
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
VGEN2LPWR VGEN2STBY
VGEN2EN
6D
6E
6F
70
71
VGEN2CTL
VGEN3CTL
VGEN4CTL
VGEN5CTL
VGEN6CTL
0
0
x
VGEN3LPWR VGEN3STBY
VGEN3EN
0
0
x
VGEN4LPWR VGEN4STBY
VGEN4EN
0
0
x
VGEN5LPWR VGEN5STBY
VGEN5EN
0
0
x
VGEN6LPWR VGEN6STBY
VGEN6EN
x
0
0
–
0
–
0
–
0
PAGE[4:0]
0
7F
Page Register
R/W 8'b0000_0000
0
0
0
0
Table 137. Extended Page 1
BITS[7:0]
Address Register Name TYPE
Default
7
–
0
6
–
0
5
–
0
4
3
–
x
2
–
x
1
–
x
0
OTP FUSE
READ EN
–
x
OTP FUSE READ
80
84
R/W
R/W
8'b000x_xxx0
8'b0000_0000
EN
0
FORCE
PWRCTL
RL OTP
FUSE
RL TRIM
FUSE
START
0
RL PWBRTN
0
RL PWRCTL
0
RL OTP
0
RL OTP ECC
0
OTP LOAD MASK
0
0
0
–
x
–
x
–
x
–
x
–
x
–
x
–
x
–
x
–
x
–
x
–
x
–
x
ECC5_SE
ECC4_SE
ECC3_SE
ECC2_SE
ECC1_SE
8A
8B
8C
8D
OTP ECC SE1
OTP ECC SE2
OTP ECC DE1
OTP ECC DE2
R
R
R
R
8'bxxx0_0000
8'bxxx0_0000
8'bxxx0_0000
8'bxxx0_0000
0
0
0
0
0
ECC10_SE
ECC9_SE
ECC8_SE
ECC7_SE
ECC6_SE
0
0
0
0
0
ECC5_DE
ECC4_DE
ECC3_DE
ECC2_DE
ECC1_DE
0
0
ECC9_DE
0
0
ECC8_DE
0
0
ECC7_DE
0
0
ECC6_DE
0
ECC10_DE
0
–
0
–
0
SW1AB_VOLT[5:0]
OTP SW1AB
VOLT
A0
R/W
8'b00xx_xxxx
x
x
x
x
x
x
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
125
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 137. Extended Page 1 (continued)
BITS[7:0]
Address Register Name TYPE
Default
7
–
0
–
0
6
5
4
3
2
1
0
SW1AB_SEQ[4:0]
x
A1
A2
OTP SW1AB SEQ
R/W
R/W
8'b000x_xxXx
8'b0000_xxxx
0
–
0
0
–
0
x
–
0
x
X
x
SW1_CONFIG[1:0]
SW1AB_FREQ[1:0]
OTP SW1AB
CONFIG
x
x
x
x
–
0
–
0
–
0
–
0
SW1C_VOLT[5:0]
x
A8
A9
AA
OTP SW1C VOLT
OTP SW1C SEQ
R/W
R/W
R/W
8'b00xx_xxxx
8'b000x_xxxx
8'b0000_00xx
x
x
x
x
x
x
x
SW1C_SEQ[4:0]
0
–
0
0
–
0
x
–
0
x
–
0
x
–
0
SW1C_FREQ[1:0]
OTP SW1C
CONFIG
x
x
–
0
–
0
–
0
SW2_VOLT[5:0]
x
AC
AD
AE
OTP SW2 VOLT
OTP SW2 SEQ
R/W
R/W
R/W
8'b0xxx_xxxx
8'b000x_xxxx
8'b0000_00xx
x
–
0
–
0
x
x
x
x
x
x
x
SW2_SEQ[4:0]
0
–
0
x
–
0
x
–
0
x
–
0
SW2_FREQ[1:0]
OTP SW2
CONFIG
x
x
–
0
–
0
–
0
SW3A_VOLT[6:0]
x
B0
B1
B2
OTP SW3A VOLT
OTP SW3A SEQ
R/W
R/W
R/W
8'b0xxx_xxxx
8'b000x_xxxx
8'b0000_xxxx
x
–
0
–
0
x
x
x
x
x
x
x
SW3A_SEQ[4:0]
x
0
–
0
x
–
0
x
x
SW3_CONFIG[1:0]
SW3A_FREQ[1:0]
OTP SW3A
CONFIG
x
x
x
–
0
–
0
–
0
SW3B_VOLT[6:0]
x
B4
B5
B6
OTP SW3B VOLT
OTP SW3B SEQ
R/W
R/W
R/W
8'b0xxx_xxxx
8'b000x_xxxx
8'b0000_00xx
x
–
0
–
0
x
x
x
x
x
x
x
SW3B_SEQ[4:0]
0
–
0
x
–
0
x
–
0
x
–
0
SW3B_CONFIG[1:0]
OTP SW3B
CONFIG
x
x
–
0
–
0
SW4_VOLT[6:0]
x
B8
B9
OTP SW4 VOLT
OTP SW4 SEQ
R/W
R/W
8'b00xx_xxxx
8'b000x_xxxx
0
–
0
x
–
0
x
x
x
x
x
x
x
SW4_SEQ[4:0]
x
x
PF0100
Analog Integrated Circuit Device Data
126
Freescale Semiconductor
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 137. Extended Page 1 (continued)
BITS[7:0]
Address Register Name TYPE
Default
7
–
0
6
–
0
5
–
0
4
3
–
x
2
–
x
1
0
VTT
x
SW4_FREQ[1:0]
OTP SW4
CONFIG
BA
R/W
8'b000x_xxxx
x
x
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
SWBST_VOLT[1:0]
OTP SWBST
VOLT
BC
BD
R/W
R/W
8'b0000_00xx
8'b0000_xxxx
0
x
x
SWBST_SEQ[4:0]
x
OTP SWBST SEQ
0
x
x
x
–
0
–
0
–
0
–
0
–
0
VSNVS_VOLT[2:0]
x
OTP VSNVS
VOLT
C0
C4
R/W
R/W
8'b0000_0xxx
8'b000x_x0xx
0
x
x
–
0
–
0
–
0
VREFDDR_SEQ[4:0]
0
OTP VREFDDR
SEQ
x
x
x
–
0
–
0
–
0
–
0
–
0
–
0
–
0
VGEN1_VOLT[3:0]
OTP VGEN1
VOLT
C8
C9
R/W
R/W
8'b0000_xxxx
8'b000x_xxxx
x
x
x
x
x
x
VGEN1_SEQ[4:0]
x
OTP VGEN1 SEQ
x
x
–
0
–
0
–
0
–
0
–
0
–
0
–
0
VGEN2_VOLT[3:0]
OTP VGEN2
VOLT
CC
CD
R/W
R/W
8'b0000_xxxx
8'b000x_xxxx
x
x
x
x
x
x
VGEN2_SEQ[4:0]
x
OTP VGEN2 SEQ
x
x
–
0
–
0
–
0
–
0
–
0
–
0
–
0
VGEN3_VOLT[3:0]
OTP VGEN3
VOLT
D0
D1
R/W
R/W
8'b0000_xxxx
8'b000x_xxxx
x
x
x
x
x
x
VGEN3_SEQ[4:0]
x
OTP VGEN3 SEQ
x
x
–
0
–
0
–
0
–
0
–
0
–
0
–
0
VGEN4_VOLT[3:0]
OTP VGEN4
VOLT
D4
D5
R/W
R/W
8'b0000_xxxx
8'b000x_xxxx
x
x
x
x
x
x
VGEN4_SEQ[4:0]
x
OTP VGEN4 SEQ
x
x
–
0
–
0
–
0
–
0
–
0
–
0
–
0
VGEN5_VOLT[3:0]
OTP VGEN5
VOLT
D8
D9
R/W
R/W
8'b0000_xxxx
8'b000x_xxxx
x
x
x
x
x
x
VGEN5_SEQ[4:0]
x
OTP VGEN5 SEQ
x
x
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
127
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 137. Extended Page 1 (continued)
BITS[7:0]
Address Register Name TYPE
Default
7
6
5
4
3
2
1
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
VGEN6_VOLT[3:0]
OTP VGEN6
VOLT
DC
DD
R/W
R/W
8'b0000_xxxx
8'b000x_xxxx
x
x
x
x
x
x
VGEN6_SEQ[4:0]
x
OTP VGEN6 SEQ
x
x
PWRON_
CFG1
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
SWDVS_CLK1[1:0]
SEQ_CLK_SPEED1[1:0]
E0
E1
E2
OTP PU CONFIG1
OTP PU CONFIG2
OTP PU CONFIG3
R/W
R/W
R/W
8'b000x_xxxx
8'b000x_xxxx
8'b000x_xxxx
x
x
x
x
x
PWRON_
CFG2
SWDVS_CLK2[1:0]
SEQ_CLK_SPEED2[1:0]
x
x
x
x
x
PWRON_
CFG3
SWDVS_CLK3[1:0]
SEQ_CLK_SPEED3[1:0]
x
x
x
x
x
PWRON_CFG
_XOR
–
–
0
–
SWDVS_CLK3_XOR
SEQ_CLK_SPEED_XOR
OTP PU CONFIG
XOR
E3
R
8'b000x_xxxx
8'b0000_00x0
0
0
–
x
x
x
x
x
SOFT_FUSE
_POR
TBB_POR
–
–
–
FUSE_POR1
–
(77)
E4
OTP FUSE POR1
R/W
0
RSVD
0
0
RSVD
0
0
–
0
–
0
0
–
0
–
0
0
–
0
–
0
0
–
0
–
0
x
0
–
0
–
0
FUSE_POR2
E5
E6
OTP FUSE POR1
OTP FUSE POR1
R/W
R/W
8'b0000_00x0
8'b0000_00x0
x
RSVD
0
RSVD
0
FUSE_POR3
x
FUSE_POR_
XOR
RSVD
RSVD
–
–
–
–
–
OTP FUSE POR
XOR
E7
E8
R
8'b0000_00x0
0
–
0
0
–
0
0
–
0
0
–
0
0
–
0
0
–
0
x
–
x
0
OTP_PG_EN
0
OTP PWRGD EN R/W/M 8'b0000_000x
EN_ECC_
BANK5
EN_ECC_
BANK4
EN_ECC_
BANK3
EN_ECC_
BANK2
EN_ECC_
BANK1
–
0
–
0
–
0
–
0
–
0
–
0
F0
OTP EN ECCO
OTP EN ECC1
R/W
R/W
8'b000x_xxxx
8'b000x_xxxx
x
x
x
x
x
EN_ECC_
BANK10
EN_ECC_
BANK9
EN_ECC_
BANK8
EN_ECC_
BANK7
EN_ECC_
BANK6
F1
x
x
x
x
x
Notes
77. In the MMPF0100 FUSE_POR1, FUSE_POR2, and FUSE_POR3 are XOR’ed into the FUSE_POR_XOR bit. The FUSE_POR_XOR
has to be 1 for fuses to be loaded. This can be achieved by setting any one or all of the FUSE_PORx bits. In MMPF0100A, the XOR
function is removed. It is required to set all of the FUSE_PORx bits to be able to load the fuses.
PF0100
Analog Integrated Circuit Device Data
128
Freescale Semiconductor
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 137. Extended Page 1 (continued)
BITS[7:0]
Address Register Name TYPE
Default
7
–
0
–
0
–
0
–
0
6
–
0
–
0
–
0
–
0
5
–
0
–
0
–
0
–
0
4
3
2
1
0
x
x
–
0
–
0
–
0
–
0
RSVD
F4
F5
F6
F7
OTP SPARE2_4
OTP SPARE4_3
OTP SPARE6_2
OTP SPARE7_1
R/W
R/W
R/W
R/W
8'b0000_xxxx
8'b0000_0xxx
8'b0000_00xx
8'b0000_0xxx
x
–
0
–
0
–
0
x
x
RSVD
x
x
–
0
–
x
RSVD
x
–
x
x
RSVD
x
–
0
–
0
–
0
–
0
–
0
–
0
–
0
OTP_DONE
x
FE
FF
OTP DONE
R/W
R/W
8'b0000_000x
8'b0000_0xxx
I2C_SLV
ADDR[3]
–
0
–
0
–
0
–
0
I2C_SLV ADDR[2:0]
x
OTP I2C ADDR
1
x
x
Table 138. Extended Page 2
BITS[7:0]
Address Register Name TYPE
Default
7
6
5
4
3
2
1
0
RSVD
1
RSVD
1
RSVD
1
RSVD
1
RSVD
1
SW1AB_PWRSTG[2:0]
1
81
82
83
84
85
86
SW1AB PWRSTG
PWRSTG RSVD
SW1C PWRSTG
SW2 PWRSTG
SW3A PWRSTG
SW3B PWRSTG
R/W
R
8'b1111_1111
8'b0000_0000
8'b1111_1111
8'b1111_1111
8'b1111_1111
8'b1111_1111
1
0
1
1
1
1
1
0
1
1
1
1
PWRSTGRSVD
0
0
RSVD
1
0
RSVD
1
0
RSVD
1
0
0
RSVD
RSVD
SW1C_PWRSTG[2:0]
R
1
RSVD
1
1
RSVD
1
1
RSVD
1
RSVD
1
RSVD
1
SW2_PWRSTG[2:0]
R
1
RSVD
1
RSVD
1
RSVD
1
RSVD
1
RSVD
1
SW3A_PWRSTG[2:0]
R
1
RSVD
1
RSVD
1
RSVD
1
RSVD
1
RSVD
1
SW3B_PWRSTG[2:0]
1
R
FSLEXT_
THERM_
DISABLE
PWRGD_
SHDWN_
DISABLE
RSVD
RSVD
RSVD
SW4_PWRSTG[2:0]
87
88
SW4 PWRSTG
R
R
8'b0111_1111
8'b0000_0001
0
–
0
0
–
0
1
–
0
1
–
0
1
–
0
1
–
0
1
1
OTP_
PWRGD_EN
SHDWN_EN
PWRCTRL OTP
CTRL
0
1
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
129
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 138. Extended Page 2 (continued)
BITS[7:0]
Address Register Name TYPE
Default
7
6
5
4
3
2
1
0
I2C_WRITE_ADDRESS_TRAP[7:0]
I2C WRITE
ADDRESS TRAP
8D
8E
R/W
R/W
8'b0000_0000
0
0
RSVD
0
0
RSVD
0
0
0
0
0
0
LET_IT_
ROLL
I2C_TRAP_PAGE[4:0]
0
I2C TRAP PAGE
8'b0000_0000
0
0
0
0
0
0
0
I2C_WRITE_ADDRESS_COUNTER[7:0]
8F
90
I2C TRAP CNTR
IO DRV
R/W
R/W
8'b0000_0000
8'b00xx_xxxx
0
0
0
0
0
0
0
x
SDA_DRV[1:0]
SDWNB_DRV[1:0]
INTB_DRV[1:0]
RESETBMCU_DRV[1:0]
0
x
x
x
x
x
AUTO_ECC
_BANK5
AUTO_ECC AUTO_ECC_ AUTO_ECC AUTO_ECC_
–
0
–
0
–
0
–
0
–
0
–
0
_BANK4
BANK3
_BANK2
BANK1
DO
D1
OTP AUTO ECC0
OTP AUTO ECC1
R/W
R/W
8'b0000_0000
8'b0000_0000
0
0
0
0
0
AUTO_ECC_ AUTO_ECC AUTO_ECC_ AUTO_ECCB AUTO_ECC_
BANK10
_BANK9
BANK8
ANK7
BANK6
0
0
0
0
0
RSVD
(78)
D8
D9
Reserved
Reserved
–
–
8'b0000_0000
8'b0000_0000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
RSVD
(78)
ECC1_EN_ ECC1_CALC
ECC1_CIN_TBB[5:0]
TBB
_CIN
E1
OTP ECC CTRL1
OTP ECC CTRL2
OTP ECC CTRL3
OTP ECC CTRL4
OTP ECC CTRL5
OTP ECC CTRL6
OTP ECC CTRL7
R/W
R/W
R/W
R/W
R/W
R/W
R/W
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ECC2_EN_ ECC2_CALC
TBB
ECC2_CIN_TBB[5:0]
_CIN
E2
E3
E4
E5
E6
E7
0
0
0
0
ECC3_EN_ ECC3_CALC
TBB
ECC3_CIN_TBB[5:0]
_CIN
0
0
0
0
ECC4_EN_ ECC4_CALC
TBB
ECC4_CIN_TBB[5:0]
_CIN
0
0
0
0
ECC5_EN_ ECC5_CALC
TBB
ECC5_CIN_TBB[5:0]
_CIN
0
0
0
0
ECC6_EN_ ECC6_CALC
TBB
ECC6_CIN_TBB[5:0]
_CIN
0
0
0
0
ECC7_EN_ ECC7_CALC
TBB
ECC7_CIN_TBB[5:0]
_CIN
0
0
0
0
PF0100
Analog Integrated Circuit Device Data
130
Freescale Semiconductor
Functional Block Requirements and Behaviors
Control Interface I2C Block Description
Table 138. Extended Page 2 (continued)
BITS[7:0]
Address Register Name TYPE
Default
7
6
5
0
0
0
4
0
0
0
3
2
1
0
0
0
0
0
0
0
ECC8_EN_ ECC8_CALC
TBB
ECC8_CIN_TBB[5:0]
_CIN
E8
E9
EA
OTP ECC CTRL8
OTP ECC CTRL9
OTP ECC CTRL10
R/W
R/W
R/W
8'b0000_0000
0
0
0
0
ECC9_EN_ ECC9_CALC
TBB
ECC9_CIN_TBB[5:0]
_CIN
8'b0000_0000
8'b0000_0000
0
0
0
0
ECC10_EN_ ECC10_CAL
ECC10_CIN_TBB[5:0]
TBB
C_CIN
0
0
0
0
ANTIFUSE1_ ANTIFUSE1_ ANTIFUSE1_
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
BYPASS1
EN
LOAD
RW
F1
F2
F3
F4
F5
F6
F7
F8
F9
OTP FUSE CTRL1
OTP FUSE CTRL2
OTP FUSE CTRL3
OTP FUSE CTRL4
OTP FUSE CTRL5
OTP FUSE CTRL6
OTP FUSE CTRL7
OTP FUSE CTRL8
OTP FUSE CTRL9
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
8'b0000_0000
0
0
0
0
ANTIFUSE2_ ANTIFUSE2_ ANTIFUSE2_
BYPASS2
EN
LOAD
RW
0
0
0
0
ANTIFUSE3_ ANTIFUSE3_ ANTIFUSE3_
BYPASS3
EN
LOAD
RW
0
0
0
0
ANTIFUSE4_ ANTIFUSE4_ ANTIFUSE4_
BYPASS4
EN
LOAD
RW
0
0
0
0
ANTIFUSE5_ ANTIFUSE5_ ANTIFUSE5_
BYPASS5
EN
LOAD
RW
0
0
0
0
ANTIFUSE6_ ANTIFUSE6_ ANTIFUSE6_
BYPASS6
EN
LOAD
RW
0
0
0
0
ANTIFUSE7_ ANTIFUSE7_ ANTIFUSE7_
BYPASS7
EN
LOAD
RW
0
0
0
0
ANTIFUSE8_ ANTIFUSE8_ ANTIFUSE8_
BYPASS8
EN
LOAD
RW
0
0
0
0
ANTIFUSE9_ ANTIFUSE99 ANTIFUSE9_
BYPASS9
EN
_LOAD
RW
0
0
0
0
ANTIFUSE10 ANTIFUSE10 ANTIFUSE10
BYPASS10
0
_EN
_LOAD
_RW
OTP FUSE
CTRL10
FA
0
0
0
Notes
78. Do not write in reserved registers.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
131
Typical Applications
Introduction
7
Typical Applications
7.1
Introduction
Figure 35 provides a typical application diagram of the PF0100 PMIC together with its functional components. For details on
component references and additional components such as filters, refer to the individual sections.
7.1.1 Application Diagram
VIN1
SW1AB Output
SW1FB
1.0uF
2.2uF
4.7uF
Vin
VIN1
4.7uF
PF0100
VGEN1
100mA
SW1AIN
SW1ALX
VGEN1
O/P
Drive
1.0uH
SW1A/B
Single/Dual
2500 mA
Buck
VGEN2
250mA
VGEN2
4 x22uF
SW1BLX
SW1BIN
O/P
Drive
VIN2
1.0uF
2.2uF
VIN2
4.7uF
4.7uF
Vin
Vin
VGEN3
100mA
SW1C Output
VGEN3
1.0uH
SW1CLX
SW1CIN
O/P
Drive
SW1C
1750 mA
Buck
VGEN4
350mA
2 x 22uF
4.7uF
VGEN4
VIN3
SW1CFB
VIN3
SW1VSSSNS
Core Control logic
1.0uF
2.2uF
VGEN5
100mA
SW2 Output
1.0uH
VGEN5
VGEN6
SW2LX
SW2IN
SW2IN
SW2FB
Initialization State Machine
SW2
2000 mA
Buck
O/P
Drive
VGEN6
200mA
2.2uF
2 x 22uF
4.7uF
Vin
SW3AFB
OTP
Supplies
Control
SW3A Output
2 x 22uF
Vin
4.7uF
SW3AIN
SW3ALX
VDDOTP
O/P
Drive
VDDOTP
VDDIO
1.0uH
1.0uH
VDDIO
SW3A/B
Single/Dual
DDR
2500 mA
Buck
CONTROL
SW3BLX
SW3BIN
I2C
Interface
0.1uF
O/P
Drive
2 x 22uF
SCL
SDA
To
MCU
4.7uF
Vin
Vin
SW3BFB
SW3B Output
DVS CONTROL
SW3VSSSNS
DVS Control
SW4FB
SW4 Output
2 x 22uF
4.7uF
2.2uH
SW4
1000 mA
Buck
SW4IN
O/P
Drive
1.0uH
I2C
Register
map
SW4LX
1uF
Trim-In-Package
VCOREDIG
VCOREREF
GNDREF1
Vin
10uF
220nF
1uF
SWBSTLX
SWBSTIN
SWBSTFB
Reference
Generation
SWBST
Output
Clocks and
resets
SWBST
600 mA
Boost
O/P
Drive
Vin
VCORE
2 x 22uF
GNDREF
2.2uF
1uF
VREFDDR
VSW3A
VINREFDDR
100nF
100nF
Vin
Clocks
32kHz and 16MHz
Package Pin Legend
VHALF
Output Pin
Input Pin
Bi-directional Pin
VIN
1uF
Best
of
Supply
Li Cell
Charger
LICELL
100nF
VSNVS
Coin Cell
Battery
VSW2
VSW2
VSW2
VSW2
0.47uF
To/From
AP
Figure 35. Typical Application Schematic
PF0100
Analog Integrated Circuit Device Data
132
Freescale Semiconductor
Typical Applications
Introduction
7.1.2 Bill of Material
The following table provides a complete list of the recommended components on a full featured system using the PF0100 Device.
Critical components such as inductors, transistors, and diodes are provided with a recommended part number, but equivalent
components may be used.
(79)
Table 139. Bill of Material
Value
PMIC
Qty
Description
Part#
Manufacturer
Component/Pin
1
Power management IC
MMPF0100
Freescale
BUCK, SW1AB - (0.300-1.875 V), 2.5 A
4 x 4 x 2.1
1.0 H
1.0 H
1.0 H
1
–
–
ISAT = 4.5 A for 10% drop,
DCRMAX = 11.9 m
XFL4020-102MEB
LPS5015_102ML
FDSD0412-H-1R0M
Coilcraft
Coilcraft
Toko
Output Inductor
5 x 5 x 1.5
ISAT = 3.6 A for 10% drop,
DCRMAX = 50 m
Output Inductor
(Alternate)
4 x 4 x 1.2
Output inductor
(Alternate)
ISAT = 6.2 A, DCR = 37 m
22 F
4.7 F
0.1 F
4
2
1
10 V X5R 0805
10 V X5R 0603
10 V X5R 0402
LMK212BJ226MG-T
LMK107BJ475KA-T
C0402C104K8PAC
Taiyo Yuden
Taiyo Yuden
Kemet
Output capacitance
Input capacitance
Input capacitance
BUCK, SW1C- (0.300-1.875 V), 2.0 A
4 x 4 x 1.2
1.0 H
1.0 H
1.0 H
1
–
–
ISAT = 2.8 A for 10% drop,
DCRMAX = 60 m
LPS4012-102NL
XFL3012-102ML
FDSD0412-H-1R0M
Coilcraft
Coilcraft
Toko
Output Inductor
3x 3 1.2
ISAT = 2.5 A for 10% drop,
DCRMAX = 42 m
Output Inductor
(Alternate)
4 x 4 x 1.2
Output inductor
(Alternate)
ISAT = 6.2 A, DCR = 37 m
22 F
4.7 F
0.1 F
2
1
1
10 V X5R 0805
10 V X5R 0603
10 V X5R 0402
LMK212BJ226MG-T
LMK107BJ475KA-T
C0402C104K8PAC
Taiyo Yuden
Taiyo Yuden
Kemet
Output capacitance
Input capacitance
Input capacitance
BUCK, SW2- (0.400-3.300 V), 2.0 A
4 x 4 x 1.2
1.0 H
1.0 H
1.0 H
1
–
–
ISAT = 2.8 A for 10% drop,
DCRMAX = 60 m
LPS4012-102NL
XFL3012-102ML
FDSD0412-H-1R0M
Coilcraft
Coilcraft
Toko
Output Inductor
3x 3 1.2
ISAT = 2.5 A for 10% drop,
DCRMAX = 42 m
Output Inductor
(Alternate)
4 x 4 x 1.2
Output inductor
(Alternate)
ISAT = 6.2 A, DCR = 37 m
22 F
2
1
10 V X5R 0805
10 V X5R 0603
LMK212BJ226MG-T
LMK107BJ475KA-T
Taiyo Yuden
Taiyo Yuden
Output capacitance
Input capacitance
4.7 F
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
133
Typical Applications
Introduction
Table 139. Bill of Material (continued) (79)
Value
0.1 F
Qty
Description
Part#
Manufacturer
Kemet
Component/Pin
1
10 V X5R 0402
C0402C104K8PAC
Input capacitance
BUCK, SW3AB - (0.400-3.300 V), 2.5 A
4 x 4 x 2.1
1.0 H
1.0 H
1.0 H
1
–
–
ISAT = 4.5 A for 10% drop,
DCRMAX = 11.9 m
XFL4020-102MEB
LPS5015_102ML
FDSD0412-H-1R0M
Coilcraft
Coilcraft
Toko
Output Inductor
5 x 5 x 1.5
ISAT = 3.6 A for 10% drop,
DCRMAX = 50 m
Output Inductor
(Alternate)
4 x 4 x 1.2
Output inductor
(Alternate)
ISAT = 6.2 A, DCR = 37 m
22 F
4.7 F
0.1 F
4
2
1
10 V X5R 0805
10 V X5R 0603
10 V X5R 0402
LMK212BJ226MG-T
LMK107BJ475KA-T
C0402C104K8PAC
Taiyo Yuden
Taiyo Yuden
Kemet
Output capacitance
Input capacitance
Input capacitance
BUCK, SW4 - (0.400-3.300V), 1A
2.5 x 2 x 1
1.0 H
1.0 H
1.0 H
1
-
ISAT = 1.8 A for 30% drop,
DCRMAX = 84 m
VLS252010ET-1R0N
XPL2010_102ML
1239AS-H-1R0M
TDK
Output Inductor
2.2 x 2.1 x 1
ISAT = 1.2 A for 10% drop,
DCRMAX = 89 m
Output Inductor
(Alternate)
Coilcraft
Toko
2.5 x 2 x 1
Output inductor
(Alternate)
–
ISAT = 3.4 A, DCR = 60 m
22 F
4.7 F
0.1 F
2
1
1
10 V X5R 0805
10 V X5R 0603
10 V X5R 0402
LMK212BJ226MG-T
LMK107BJ475KA-T
C0402C104K8PAC
Taiyo Yuden
Taiyo Yuden
Kemet
Output capacitance
Input capacitance
Input capacitance
BOOST, SWBST - 5.0 V, 600 MA
3 x 3 x 1.5
2.2 H
2.2 H
1
–
ISAT = 2.0 A for 10% drop,
DCRMAX = 110 m
LPS3015-222ML
Coilcraft
Toko
Output Inductor
3 x 3 x 1.2
Output inductor
(Alternate)
FDSD0312-H-2R2M
ISAT = 3.1 A, DCR = 105 m
22 F
10 F
2.2 F
0.1 F
1.0 A
2
1
1
1
1
10 V X5R 0805
10 V X5R 0805
6.3 V X5R 0402
10 V X5R 0402
20 V SOD-123FL
LMK212BJ226MG-T
C2012X5R1A106MT
C0402C225M9PACTU
C0402C104K8PAC
MBR120VLSFT1G
Taiyo Yuden
TDK
Output capacitance
Input capacitance
Input capacitance
Input capacitance
Schottky Diode
Kemet
Kemet
ON Semiconductor
LDO, VGEN1 - (0.80-1.55), 100 MA
2.2 F
1.0 F
1
1
6.3 V X5R 0402
10 V X5R 0402
C0402C225M9PACTU
CC0402KRX5R6BB105
Kemet
Output capacitance
Input capacitance
Yageo America
PF0100
Analog Integrated Circuit Device Data
134
Freescale Semiconductor
Typical Applications
Introduction
Table 139. Bill of Material (continued) (79)
Value
Qty
Description
Part#
Manufacturer
Component/Pin
LDO, VGEN2 - (0.80-1.55), 250 MA
4.7 F
1
6.3 V X5R 0402
C0402X5R6R3-475MNP
Venkel
Output capacitance
LDO, VGEN3 - (1.80-3.30), 100 MA
2.2 F
1.0 F
1
1
6.3 V X5R 0402
10 V X5R 0402
C0402C225M9PACTU
CC0402KRX5R6BB105
Kemet
Output capacitance
Input capacitance
Yageo America
LDO, VGEN4 - (1.80-3.30), 350 MA
4.7 F
1
6.3 V X5R 0402
C0402X5R6R3-475MNP
Venkel
Output capacitance
LDO, VGEN5 - (1.80-3.30), 150 MA
2.2 F
1.0 F
1
1
6.3 V X5R 0402
10 V X5R 0402
C0402C225M9PACTU
CC0402KRX5R6BB105
Kemet
Output capacitance
Input capacitance
Yageo America
LDO, VGEN6 - (1.80-3.30), 200 MA
2.2 F
1
6.3 V X5R 0402
C0402C225M9PACTU
C1005X5R0J474K
Kemet
TDK
Output capacitance
Output capacitance
Output capacitance
LDO/SWITCH VSNVS - (1.1-3.3), 200 MA
0.47 F
1
6.3 V X5R 0402
REFERENCE, VREFDDR - (0.20-1.65V), 10 MA
1.0 F
0.1 F
1
2
10 V X5R 0402
10 V X5R 0402
CC0402KRX5R6BB105
C0402C104K8PAC
Yageo America
Kemet
VHALF,
VINREFDDR
INTERNAL REFERENCES, VCOREDIG, VCOREREF, VCORE
1.0 F
1
1
1
10 V X5R 0402
10 V X5R 0402
10 V X5R 0402
CC0402KRX5R6BB105
CC0402KRX5R6BB105
GRM155R61A224KE19D
Yageo America
Yageo America
Murata
VCOREDIG
VCORE
1.0 F
0.22 F
COIN CELL
0.1 F
VCOREREF
1
10 V X5R 0402
C0402C104K8PAC
Kemet
LICELL
MISCELLANEOUS
0.1 F
1.0 F
100 k
100 k
100 k
100 k
Notes
1
1
1
1
1
1
10 V X5R 0402
10 V X5R 0402
1/16 W 0402
1/16 W 0402
1/16 W 0402
1/16 W 0402
CD402C104K8PAC
CC0402KRX5R6BB105
RK73H1ETTP1003F
RK73H1ETTP1003F
RK73H1ETTP1003F
RK73H1ETTP1003F
Kemet
VDDIO
VIN
Yageo America
KOA SPEER
KOA SPEER
KOA SPEER
KOA SPEER
PWRON
RESETBMCU
SDWN
INTB
79. Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings
or tables. While Freescale offers component recommendations in this configuration, it is the customer’s responsibility to validate their
application.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
135
Typical Applications
PF0100 Layout Guidelines
7.2
PF0100 Layout Guidelines
7.2.1 General Board Recommendations
1. It is recommended to use an eight layer board stack-up arranged as follows:
• High current signal
• GND
• Signal
• Power
• Power
• Signal
• GND
• High current signal
2. Allocate TOP and BOTTOM PCB Layers for POWER ROUTING (high current signals), copper-pour the unused area.
3. Use internal layers sandwiched between two GND planes for the SIGNAL routing.
7.2.2 Component Placement
It is desirable to keep all component related to the power stage as close to the PMIC as possible, specially decoupling input and
output capacitors.
7.2.3 General Routing Requirements
1. Some recommended things to keep in mind for manufacturability:
•
•
•
•
Via in pads require a 4.5 mil minimum annular ring. Pad must be 9.0 mils larger than the hole
Maximum copper thickness for lines less than 5.0 mils wide is 0.6 oz copper
Minimum allowed spacing between line and hole pad is 3.5 mils
Minimum allowed spacing between line and line is 3.0 mils
2. Care must be taken with SWxFB pins traces. These signals are susceptible to noise and must be routed far away from
power, clock, or high power signals, like the ones on the SWxIN, SWx, SWxLX, SWBSTIN, SWBST, and SWBSTLX pins.
They could be also shielded.
3. Shield feedback traces of the regulators and keep them as short as possible (trace them on the bottom so the ground and
power planes shield these traces).
4. Avoid coupling traces between important signal/low noise supplies (like REFCORE, VCORE, VCOREDIG) from any
switching node (i.e. SW1ALX, SW1BLX, SW1CLX, SW2LX, SW3ALX, SW3BLX, SW4LX, and SWBSTLX).
5. Make sure that all components related to a specific block are referenced to the corresponding ground.
PF0100
Analog Integrated Circuit Device Data
136
Freescale Semiconductor
Typical Applications
PF0100 Layout Guidelines
7.2.4 Parallel Routing Requirements
1. I2C signal routing
•
CLK is the fastest signal of the system, so it must be given special care.
•
To avoid contamination of these delicate signals by nearby high power or high frequency signals, it is a good
practice to shield them with ground planes placed on adjacent layers. Make sure the ground plane is uniform
throughout the whole signal trace length.
Figure 36. Recommended Shielding for Critical Signals
•
These signals can be placed on an outer layer of the board to reduce their capacitance with respect to the ground
plane.
•
Care must be taken with these signals not to contaminate analog signals, as they are high frequency signals.
Another good practice is to trace them perpendicularly on different layers, so there is a minimum area of proximity
between signals.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
137
Typical Applications
PF0100 Layout Guidelines
7.2.5 Switching Regulator Layout Recommendations
1. Per design, the switching regulators in PF0100 are designed to operate with only one input bulk capacitor. However, it is
recommended to add a high frequency filter input capacitor (CIN_hf), to filter out any noise at the regulator input. This
capacitor should be in the range of 100 nF and should be placed right next to or under the IC, closest to the IC pins.
2. Make high-current ripple traces low-inductance (short, high W/L ratio).
3. Make high-current traces wide or copper islands.
4. Make high-current traces symetrical for dual–phase regulators (SW1, SW3).
VIN
SWxIN
CIN_HF
CIN
SWx
SWxLX
Driver Controller
L
COUT
SWxFB
Compensation
Figure 37. Generic Buck Regulator Architecture
Figure 38. Layout Example for Buck Regulators
PF0100
Analog Integrated Circuit Device Data
138
Freescale Semiconductor
Typical Applications
Thermal Information
7.3
Thermal Information
7.3.1 Rating Data
The thermal rating data of the packages has been simulated with the results listed in Table 6.
Junction to Ambient Thermal Resistance Nomenclature: the JEDEC specification reserves the symbol RθJA or θJA (Theta-JA)
strictly for junction-to-ambient thermal resistance on a 1s test board in natural convection environment. RθJMA or θJMA (Theta-
JMA) will be used for both junction-to-ambient on a 2s2p test board in natural convection and for junction-to-ambient with forced
convection on both 1s and 2s2p test boards. It is anticipated that the generic name, Theta-JA, will continue to be commonly used.
The JEDEC standards can be consulted at http://www.jedec.org.
7.3.2 Estimation of Junction Temperature
An estimation of the chip junction temperature TJ can be obtained from the equation:
TJ = TA + (RθJA x PD)
with:
TA = Ambient temperature for the package in °C
RJA = Junction to ambient thermal resistance in °C/W
PD = Power dissipation in the package in W
The junction to ambient thermal resistance is an industry standard value that provides a quick and easy estimation of thermal
performance. Unfortunately, there are two values in common usage: the value determined on a single layer board RθJA and the
value obtained on a four layer board RθJMA. Actual application PCBs show a performance close to the simulated four layer board
value although this may be somewhat degraded in case of significant power dissipated by other components placed close to the
device.
At a known board temperature, the junction temperature TJ is estimated using the following equation
TJ = TB + (RθJB x PD) with
TB = Board temperature at the package perimeter in °C
RθJB = Junction to board thermal resistance in °C/W
PD = Power dissipation in the package in W
When the heat loss from the package case to the air can be ignored, acceptable predictions of junction temperature can be made.
See Functional Block Requirements and Behaviors for more details on thermal management.
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
139
Packaging
Packaging Dimensions
8
Packaging
8.1
Packaging Dimensions
Package dimensions are provided in package drawings. To find the most current package outline drawing, go to
www.freescale.com and perform a keyword search for the drawing’s document number. See the Thermal Characteristics section
for specific thermal characteristics for each package.
Table 140. Package Drawing Information
Package
Suffix
Package Outline Drawing Number
98ASA00405D
56 QFN 8x8 mm - 0.5 mm pitch.
E-Type (full lead)
EP
56 QFN 8x8 mm - 0.5 mm pitch.
WF-Type (wettable flank)
ES
98ASA00589D
PF0100
Analog Integrated Circuit Device Data
140
Freescale Semiconductor
Packaging
Packaging Dimensions
EP SUFFIX
56-PIN QFN
98ASA00405D
ISSUE 0
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
141
Packaging
Packaging Dimensions
EP SUFFIX
56-PIN QFN
98ASA00405D
ISSUE 0
PF0100
Analog Integrated Circuit Device Data
142
Freescale Semiconductor
Packaging
Packaging Dimensions
EP SUFFIX
56-PIN QFN
98ASA00405D
ISSUE 0
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
143
Packaging
Packaging Dimensions
ES SUFFIX
56-PIN QFN
98ASA00589D
ISSUE A
PF0100
Analog Integrated Circuit Device Data
144
Freescale Semiconductor
Packaging
Packaging Dimensions
ES SUFFIX
56-PIN QFN
98ASA00589D
ISSUE A
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
145
Packaging
Packaging Dimensions
ES SUFFIX
56-PIN QFN
98ASA00589D
ISSUE A
PF0100
Analog Integrated Circuit Device Data
146
Freescale Semiconductor
Reference Section
Reference Documents
9
Reference Section
9.1
Reference Documents
Table 141. PF0100 Reference Documents
Reference
Description
AN4536
MMPF0100 OTP Programming Instructions
PF0100
Analog Integrated Circuit Device Data
Freescale Semiconductor
147
Revision History
Reference Documents
10 Revision History
REVISION
DATE
7/2011
8/2012
10/2012
5/2013
DESCRIPTION OF CHANGES
Preliminary specification release
•
•
•
1.0
2.0
3.0
4.0
NPI phase: prototype major updates throughout cycle
Initial production release
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Table 4. Added recommended pin connection when regulators are unused
Update Table 9. Current Consumption summary
Table 10. Removed VREFDDR_VOLT row
Removed automatic fuse programming feature
Updated Max frequency specification for the 16 MHz clock to 17.2 MHz
Table 17. Added specification for derived 2.0 Mhz clock
Added Clock adjustment
Table 22. Updated VREFDDR minimum Current limit specification
Updated Block diagram for all Switching Regulators
Updated current limit and overcurrent protection minimum specification on LDOS
Table 111. Update VTH0 and VTL0 specification on VSNVS
Updated Table 137, Address FF
Updated Table 138, address D8 and D9
Update Figure 35. Typical application diagram
Removed Part Identification section
•
•
Added part numbers to the ordering information for the MMPF0100A
Added corrections and notes to the document to accomodate the new part numbers, where
identified by MMPF0100A
5.0
7/2013
•
VIN Threshold (Coin Cell Powered to VIN Powered) Max. changed to 3.1
•
•
Removed LICELL connection to VIN on PF0100A
Removed 4.7 F LICELL bypass capacitor as coin cell replacement
6.0
7.0
8/2013
•
•
•
•
•
Updated typical and max Off Current
Add bypass capacitor in VDDIO
Added industrial part numbers PMPF0100xxANES
Added parts F3 and F4
Added Table 3, Ambient Temperature Range and updated specification headers
accordingly.
12/2013
•
•
•
•
•
Increased max standby and sleep currents on Extended Industrial parts.
Update output accuracy on SW1A/B, SW1C, SW2, SW3A/B and SW4.
Corrected the default value on DEVICEID register, bit4 (unused) from 0 to 1.
Corrected default register values on Table 118.
Added VDDIO capacitor to Miscellaneous in the BOM
•
Corrected VDDOTP maximum rating
8.0
4/2014
•
•
•
•
•
•
•
•
Corrected SWBSTFB maximum rating
Corrected inductor Isat for SW1ABC single phase mode from 4.5 A to 6.0 A
Added note to clarify SWBST default operation in Auto mode
Corrected default value of bits in SILICONREVID register in Table 136
Changed VSNVS current limit for PF0100A
Noted that voltage settings 0.6V and below are not supported
VSNVS Turn On Delay (td1) spec corrected from 15 ms to 5.0 ms
Updated per GPCN 16298
•
Corrected GPCN number in the revision history table (16220 changed to 16298)
6/2014
PF0100
Analog Integrated Circuit Device Data
148
Freescale Semiconductor
Information in this document is provided solely to enable system and software implementers to use Freescale products.
There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based
on the information in this document.
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no
warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance
may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by
customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others.
Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address:
freescale.com/SalesTermsandConditions.
Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off.
SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their
respective owners.
© 2014 Freescale Semiconductor, Inc.
Document Number: MMPF0100
Rev. 8.0
6/2014
相关型号：
©2020 ICPDF网 联系我们和版权申明