MPC603RZT200LX [NXP]
32-BIT, 200MHz, RISC PROCESSOR, PBGA255, 23 X 23 MM, 2.60 MM HEIGHT, 1.27 MM PITCH, PLASTIC, BGA-255;型号: | MPC603RZT200LX |
厂家: | NXP |
描述: | 32-BIT, 200MHz, RISC PROCESSOR, PBGA255, 23 X 23 MM, 2.60 MM HEIGHT, 1.27 MM PITCH, PLASTIC, BGA-255 时钟 外围集成电路 |
文件: | 总31页 (文件大小:471K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Document Number: MPC603E7TEC
Rev. 5, 09/2011
Freescale Semiconductor
Technical Data
PowerPC 603e RISC Microprocessor Family:
PID7t-603e Hardware Specifications
Contents
The PowerPC™ 603e microprocessor is an implementation
of the PowerPC family of reduced instruction set computing
1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
(RISC) microprocessors. In this document, the term ‘603e’
3. General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Electrical and Thermal Characteristics . . . . . . . . . . . . 4
is used as an abbreviation for the PowerPC 603e
microprocessor. The PowerPC 603e microprocessors are
available from Freescale as MPC603e.
5. Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6. Pinout Listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7. Package Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 17
8. System Design Information . . . . . . . . . . . . . . . . . . . . 20
The 603e is implemented in several semiconductor
fabrication processes. Different processes may require
9. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . 29
10. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
different supply voltages and may have other electrical
differences but will have the same functionality. As a
technical designator to distinguish between 603e
implementations in various processes, a prefix composed of
the processor version register (PVR) value and a process
identifier (PID) is assigned to the various implementations as
shown in Table 1.
This document describes the pertinent physical
characteristics of the PID7t-603e from Freescale. For
functional characteristics of the 603e, refer to the PowerPC
603e RISC Microprocessor User’s Manual.
To locate any published errata or updates for this document,
refer to the website at www.freescale.com.
© Freescale Semiconductor, Inc., 2011. All rights reserved.
Overview
Table 1. PowerPC 603e Microprocessors from Freescale
Technical
Designator
Core Voltage I/O Voltage
5-Volt
Tolerant
Process
Part Number
(V)
(V)
PID6-603e
0.5 µm CMOS, 4LM
3.3
2.5
2.5
3.3
3.3
3.3
Yes
Yes
Yes
MPC603E
XPC603P (end-of-life)
MPC603R
PID7v-603e 0.35 µm CMOS, 5LM
PID7t-603e 0.29 µm CMOS, 5LM
1 Overview
The 603e is a low-power implementation of the PowerPC microprocessor family of RISC
microprocessors. The 603e implements the 32-bit portion of the PowerPC architecture specification that
provides 32-bit effective addresses, integer data types of 8, 16, and 32 bits, and floating-point data types
of 32 and 64 bits. For 64-bit PowerPC microprocessors, the PowerPC architecture provides 64-bit integer
data types, 64-bit addressing, and other features required to complete the 64-bit architecture.
The 603e provides four software controllable power-saving modes. Three of the modes (the nap, doze, and
sleep) are static in nature, and progressively reduce the amount of power dissipated by the processor. The
fourth is a dynamic power management mode that causes the functional units in the 603e to automatically
enter a low-power mode when the functional units are idle without affecting operational performance,
software execution, or any external hardware.
The 603e is a superscalar processor capable of issuing and retiring as many as three instructions per clock.
Instructions can execute out of order for increased performance; however, the 603e makes completion
appear sequential.
The 603e integrates five execution units—an integer unit (IU), a floating-point unit (FPU), a branch
processing unit (BPU), a load/store unit (LSU), and a system register unit (SRU). The ability to execute
five instructions in parallel and the use of simple instructions with rapid execution times yield high
efficiency and throughput for 603e-based systems. Most integer instructions execute in one clock cycle.
The FPU is pipelined, so a single-precision multiply-add instruction can be issued every clock cycle.
The 603e provides independent on-chip, 16-Kbyte, four-way set-associative, physically addressed caches
for instructions and data and on-chip instruction and data memory management units (MMUs). The
MMUs contain 64-entry, two-way, set-associative data and instruction translation lookaside buffers
(DTLB and ITLB) that provide support for demand-paged virtual memory address translation and
variable-sized block translation. The TLBs and caches use a least-recently used (LRU) replacement
algorithm. The 603e also supports block address translation through the use of two independent instruction
and data block address translation (IBAT and DBAT) arrays of four entries each. Effective addresses are
compared simultaneously with all four entries in the BAT array during block translation. In accordance
with the PowerPC architecture, if an effective address hits in both the TLB and BAT array, the BAT
translation takes priority.
The 603e has a selectable 32- or 64-bit data bus and a 32-bit address bus. The 603e interface protocol
allows multiple masters to compete for system resources through a central external arbiter. The 603e
provides a three-state coherency protocol that supports the exclusive, modified, and invalid cache states.
This protocol is a compatible subset of the MESI (modified/exclusive/shared/invalid) four-state protocol
PID7t-603e Hardware Specifications, Rev. 5
2
Freescale Semiconductor
Features
and operates coherently in systems that contain four-state caches. The 603e supports single-beat and burst
data transfers for memory accesses, and supports memory-mapped I/O.
The 603e uses an advanced, 2.5/3.3-V CMOS process technology and maintains full interface
compatibility with TTL devices. The PID7t-603e is offered in both PBGA and CBGA packages. The
CBGA package supports speed bins of 200, 266, and 300 MHz. The PBGA package is a pin-compatible
drop in replacement for the CBGA; however, this package only supports speeds up to 200 MHz.
2 Features
This section summarizes features of the 603e’s implementation of the PowerPC architecture. Major
features of the 603e are as follows:
•
High-performance, superscalar microprocessor
— As many as three instructions issued and retired per clock
— As many as five instructions in execution per clock
— Single-cycle execution for most instructions
— Pipelined FPU for all single-precision and most double-precision operations
Five independent execution units and two register files
— BPU featuring static branch prediction
•
— A 32-bit IU
— Fully IEEE 754-compliant FPU for both single- and double-precision operations
— LSU for data transfer between data cache and GPRs and FPRs
— SRU that executes condition register (CR), special-purpose register (SPR) instructions, and
integer add/compare instructions
— 32 GPRs for integer operands
— 32 FPRs for single- or double-precision operands
•
High instruction and data throughput
— Zero-cycle branch capability (branch folding)
— Programmable static branch prediction on unresolved conditional branches
— Instruction fetch unit capable of fetching two instructions per clock from the instruction cache
— A six-entry instruction queue that provides lookahead capability
— Independent pipelines with feed-forwarding that reduces data dependencies in hardware
— 16-Kbyte data cache—four-way, set-associative physically addressed; LRU replacement
algorithm
— 16-Kbyte instruction cache—four-way, set-associative physically addressed; LRU
replacement algorithm
— Cache write-back or write-through operation programmable on a per page or per block basis
— BPU that performs CR lookahead operations
— Address translation facilities for 4-Kbyte page size, variable block size, and 256-Mbyte
segment size
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
3
General Parameters
— A 64-entry two-way, set-associative ITLB
— A 64-entry two-way, set-associative DTLB
— Four-entry data and instruction BAT arrays providing 128-Kbyte to 256-Mbyte blocks
— Software table search operations and updates supported through fast trap mechanism
— 52-bit virtual and 32-bit physical address
•
•
Facilities for enhanced system performance
— A 32- or 64-bit split-transaction external data bus with burst transfers
— Support for one-level address pipelining and out-of-order bus transactions
Integrated power management
— Low-power 2.5/3.3-volt design
— Internal processor/bus clock multiplier that provides 2:1, 2.5:1, 3:1, 3.5:1, 4:1, 4.5:1, 5:1, 5.5:1,
and 6:1 ratios
— Three power-saving modes: doze, nap, and sleep
— Automatic dynamic power reduction when internal functional units are idle
In-system testability and debugging features through JTAG boundary-scan capability
•
3 General Parameters
The following list provides a summary of the general parameters of the PID7t-603e:
Technology
Die size
0.29 µm CMOS, five-layer metal
2
5.65 mm x 7.7 mm (44 mm )
Transistor count
Logic design
Package
2.6 million
Fully-static
255 ceramic ball grid array (CBGA)
or 225 thin map plastic ball grid array (PBGA)
Core power supply
I/O power supply
2.5 ± 5% V dc
3.3 ± 5% V dc
4 Electrical and Thermal Characteristics
This section provides the AC and DC electrical specifications and thermal characteristics for the
PID7t-603e.
4.1
DC Electrical Characteristics
The tables in this section describe the PID7t-603e DC electrical characteristics. This table provides the
absolute maximum ratings.
PID7t-603e Hardware Specifications, Rev. 5
4
Freescale Semiconductor
Electrical and Thermal Characteristics
Table 2. Absolute Maximum Ratings
Symbol
Characteristic
Value
Unit
Core supply voltage
PLL supply voltage
I/O supply voltage
Input voltage
Vdd
AVdd
OVdd
Vin
–0.3 to 2.75
–0.3 to 2.75
–0.3 to 3.6
–0.3 to 5.5
–55 to 150
V
V
V
V
Storage temperature range
Tstg
°C
Note:
1. Functional and tested operating conditions are given in Table 3. Absolute maximum ratings are stress ratings only, and
functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause
permanent damage to the device.
2. Caution: Vin must not exceed OVdd by more than 2.5 V at any time, including during power-on reset.
3. Caution: OVdd must not exceed Vdd/AVdd by more than 1.2 V at any time, including during power-on reset.
4. Caution: Vdd/AVdd must not exceed OVdd by more than 0.4 V at any time, including during power-on reset.
This table provides the recommended operating conditions for the PID7t-603e.
Table 3. Recommended Operating Conditions
Characteristic
Symbol
Value
Unit
Core supply voltage
PLL supply voltage
I/O supply voltage
Input voltage
Vdd
AVdd
OVdd
Vin
2.375 to 2.625
2.375 to 2.625
3.135 to 3.465
GND to 5.5
V
V
V
V
Die-junction temperature
Tj
0 to 105
°C
Note: These are the recommended and tested operating conditions. Proper device operation outside of these conditions is not
guaranteed.
This table provides the package thermal characteristics for the PID7t-603e.
Table 4. Package Thermal Characteristics
Value Value
CBGA PBGA
Characteristic
Symbol
Rating
Package die junction-to-case thermal resistance (typical)
Package die junction-to-ball thermal resistance (typical)
JC
JB
0.095
3.5
8.0
13
°C/W
°C/W
Note: For more about thermal management, see Section 8, “System Design Information.”
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
5
Electrical and Thermal Characteristics
This table provides the DC electrical characteristics for the PID7t-603e.
Table 5. DC Electrical Specifications
Vdd = AVdd = 2.5 ± 5% V dc, OVdd = 3.3 ± 5% V dc, GND = 0 V dc, 0 Tj 105 °C
Characteristic
Symbol
Min
Max
Unit
Note
Input high voltage (all inputs except SYSCLK)
Input low voltage (all inputs except SYSCLK)
SYSCLK input high voltage
VIH
VIL
2.0
GND
2.4
GND
—
5.5
0.8
5.5
0.4
30
V
V
—
—
CVIH
CVIL
Iin
V
—
SYSCLK input low voltage
V
—
Input leakage current, Vin = 3.465 V
Vin = 5.5 V
µA
µA
µA
µA
V
1, 2
1, 2
1, 2
1, 2
—
Iin
—
300
30
Hi-Z (off-state) leakage current, Vin = 3.465 V
Vin = 5.5 V
ITSI
ITSI
VOH
VOL
Cin
—
—
300
—
Output high voltage, IOH = –7 mA
Output low voltage, IOL = 7 mA
2.4
—
0.4
10.0
15.0
V
—
Capacitance, Vin = 0 V, f = 1 MHz (excludes TS, ABB, DBB, and ARTRY)
Capacitance, Vin = 0 V, f = 1 MHz (for TS, ABB, DBB, and ARTRY)
Notes:
—
pF
pF
3
Cin
—
3
1. Excludes test signals (LSSD_MODE, L1_TSTCLK, L2_TSTCLK, and JTAG signals).
2. The leakage is measured for nominal OVdd and Vdd or both OVdd and Vdd must vary in the same direction (for example, both
OVdd and Vdd vary by either +5% or -5%).
3. Capacitance is periodically sampled rather than 100% tested.
This table provides the power consumption for the PID7t-603e.
Table 6. Power Consumption
Processor (CPU) Frequency
Unit
100 MHz 133 MHz 166 MHz 200 MHz 233 MHz 266 MHz 300 MHz
Full-On Mode (DPM Enabled)
Typical
1.1
1.6
1.6
2.4
2.1
3.2
2.5
4.0
3.0
4.6
3.5
5.3
4.0
6.0
W
W
Maximum
Doze Mode
Typical
0.55
50
0.7
60
50
0.9
75
55
1.1
85
65
1.3
100
75
1.5
120
90
1.8
130
100
W
Nap Mode
Typical
mW
mW
Sleep Mode
Typical
45
Sleep Mode—PLL Disabled
PID7t-603e Hardware Specifications, Rev. 5
6
Freescale Semiconductor
Electrical and Thermal Characteristics
Table 6. Power Consumption (continued)
Processor (CPU) Frequency
Unit
100 MHz 133 MHz 166 MHz 200 MHz 233 MHz 266 MHz 300 MHz
Typical
40
40
40
40
40
40
40
mW
Sleep Mode—PLL and SYSCLK Disabled
Typical
Maximum
Note:
15
25
15
25
15
25
15
25
15
25
15
80
15
mW
mW
100
1. These values apply for all valid PLL_CFG[0–3] settings and do not include output driver power (OVdd) or analog supply
power (AVdd). OVdd power is system dependent but is typically 10% of Vdd. Worst-case AVdd = 15 mW.
2. Typical power is an average value measured at Vdd = AVdd = 2.5 V, OVdd = 3.3V, in a system executing typical applications
and benchmark sequences.
3. Maximum power is measured at 2.625 V using a worst-case instruction mix.
4.2
AC Electrical Characteristics
This section provides the AC electrical characteristics for the PID7t-603e. These specifications are for 200,
266, and 300 MHz processor speed grades. The processor core frequency is determined by the bus
(SYSCLK) frequency and the settings of the PLL_CFG[0–3] signals. All timings are specified respective
to the rising edge of SYSCLK. PLL_CFG signals should be set prior to power up and not altered
afterwards.
4.2.1
Clock AC Specifications
This table provides the clock AC timing specifications as defined in Figure 1. After fabrication, parts are
sorted by maximum processor core frequency as shown in Section 4.2.1, “Clock AC Specifications,” and
tested for conformance to the AC specifications for that frequency. Parts are sold by maximum processor
core frequency; see Section 9, “Ordering Information.”
Table 7. Clock AC Timing Specifications
Vdd = AVdd = 2.5 ± 5% V dc, OVdd = 3.3 ± 5% V dc, GND = 0 V dc, 0 Tj 105 °C
200 MHz
PBGA
200 MHz
CBGA
266 MHz
CBGA
300 MHz
CBGA
Num
Characteristic
Unit
Note
Min
Max
Min
Max
Min
Max
Min
Max
Processor frequency
VCO frequency
100
300
25
200
400
66.67
40
80
300
25
200
400
66.67
40
150
300
25
266
532
75
180
360
33.3
13.3
—
300
600
75
MHz
MHz
MHz
ns
1, 6
1
SYSCLK frequency
SYSCLK cycle time
1
1
13.3
—
13.3
—
13.3
—
40
30
2, 3 SYSCLK rise and fall time
2.0
2.0
2.0
60.0
2.0
60.0
ns
2
3
4
SYSCLK duty cycle measured 40.0
at 1.4 V
60.0
40.0
60.0
40.0
40.0
%
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
7
Electrical and Thermal Characteristics
Table 7. Clock AC Timing Specifications (continued)
Vdd = AVdd = 2.5 ± 5% V dc, OVdd = 3.3 ± 5% V dc, GND = 0 V dc, 0 Tj 105 °C
200 MHz
PBGA
200 MHz
CBGA
266 MHz
CBGA
300 MHz
CBGA
Num
Characteristic
Unit
Note
Min
Max
Min
Max
Min
Max
Min
Max
SYSCLK jitter
PID7t internal PLL-relock time
—
—
±150
100
—
—
±150
100
—
—
±150
100
—
—
±150
100
ps
4
s
3, 5
Note:
1. Caution: The SYSCLK frequency and PLL_CFG[0–3] settings must be chosen such that the resulting SYSCLK (bus)
frequency, CPU (core) frequency, and PLL (VCO) frequency do not exceed their respective maximum or minimum operating
frequencies. Refer to the PLL_CFG[0–3] signal description in Section 8, “System Design Information,” for valid
PLL_CFG[0–3] settings.
2. Rise and fall times for the SYSCLK input are measured from 0.4 V to 2.4 V.
3. Timing is guaranteed by design and characterization, and is not tested.
4. Cycle-to-cycle jitter, and is guaranteed by design. The total input jitter (short term and long term combined) must be under
±150 ps to guarantee the input/output timing of Section 4.2.2, “Input AC Specifications,” and Section 4.2.3, “Output AC
Specifications.”
5. Relock timing is guaranteed by design and characterization, and is not tested. PLL-relock time is the maximum time required
for PLL lock after a stable Vdd, OVdd, AVdd, and SYSCLK are reached during the power-on reset sequence. This specification
also applies when the PLL has been disabled and subsequently re-enabled during sleep mode. Also note that HRESET must
be held asserted for a minimum of 255 bus clocks after the PLL-relock time (100 s) during the power-on reset sequence.
6. Operation below 150 MHz is supported only by PLL_CFG[0–3] = 0b0101. Refer to Section 8.1, “PLL Configuration” for
additional information.
This figure provides the SYSCLK input timing diagram.
1
4
4
2
3
CVih
VM
VM
VM
SYSCLK
CVil
VM = Midpoint Voltage (1.4 V)
Figure 1. SYSCLK Input Timing Diagram
4.2.2
Input AC Specifications
This table provides the input AC timing specifications for the PID7t-603e as defined in Figure 2 and
Figure 3.
PID7t-603e Hardware Specifications, Rev. 5
8
Freescale Semiconductor
Electrical and Thermal Characteristics
1
Table 8. Input AC Timing Specifications
Vdd = AVdd = 2.5 ± 5% V dc, OVdd = 3.3 ± 5% V dc, GND = 0 V dc, 0 Tj 105° C
200, 266, 300 MHz
Num
Characteristic
Unit
Notes
Min
Max
10a
10b
10c
Address/data/transfer attribute inputs valid to SYSCLK (input setup)
All other inputs valid to SYSCLK (input setup)
2.5
3.5
8
—
—
—
ns
ns
2
3
Mode select inputs valid to HRESET (input setup)
(for DRTRY, QACK and TLBISYNC)
tsysclk
4, 5, 6, 7
11a
11b
11c
SYSCLK to address/data/transfer attribute inputs invalid (input hold)
SYSCLK to all other inputs invalid (input hold)
1.0
1.0
0
—
—
—
ns
ns
ns
2
3
HRESET to mode select inputs invalid (input hold)
(for DRTRY, QACK, and TLBISYNC)
4, 6, 7
Note:
1. Input specifications are measured from the TTL level (0.8 or 2.0 V) of the signal in question to the 1.4 V of the rising edge of
the input SYSCLK. Input and output timings are measured at the pin.
2. Address/data/transfer attribute input signals are composed of the following—A[0–31], AP[0–3], TT[0–4], TC[0–1], TBST,
TSIZ[0–2], GBL, DH[0–31], DL[0–31], DP[0–7].
3. All other input signals are composed of the following—TS, ABB, DBB, ARTRY, BG, AACK, DBG, DBWO, TA, DRTRY, TEA,
DBDIS, HRESET, SRESET, INT, SMI, MCP, TBEN, QACK, TLBISYNC.
4. The setup and hold time is with respect to the rising edge of HRESET (see Figure 3).
5. tsysclk is the period of the external clock (SYSCLK) in nanoseconds (ns). The numbers given in the table must be multiplied
by the period of SYSCLK to compute the actual time duration (in nanoseconds) of the parameter in question.
6. These values are guaranteed by design, and are not tested.
7. This specification is for configuration mode only. Also note that HRESET must be held asserted for a minimum of 255 bus
clocks after the PLL-relock time during the power-on reset sequence.
This figure provides the input timing diagram for the PID7t-603e.
VM
SYSCLK
10a
10b
11a
11b
ALL INPUTS
VM = Midpoint Voltage (1.4 V)
Figure 2. Input Timing Diagram
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
9
Electrical and Thermal Characteristics
This figure provides the mode select input timing diagram for the PID7t-603e.
VM
HRESET
10c
11c
MODE PINS
VM = Midpoint Voltage (1.4 V)
Figure 3. Mode Select Input Timing Diagram
4.2.3
Output AC Specifications
This table provides the output AC timing specifications for the PID7t-603e as defined in Figure 4.
1
Table 9. Output AC Timing Specifications
Vdd = AVdd = 2.5 5% V dc, OVdd = 3.3 ± 5%, GND = 0 V dc, 0 Tj 105 °C, C = 50 pF (unless otherwise noted)
L
200, 266, 300 MHz
Num
Characteristic
Unit
Note
Min
Max
12
SYSCLK to output driven (output enable time)
1.0
—
—
—
—
9.0
ns
ns
ns
ns
—
3
13a
13b
14a
SYSCLK to output valid (5.5 V to 0.8 V—TS, ABB, ARTRY, DBB)
SYSCLK to output valid (TS, ABB, ARTRY, DBB)
8.0
5
SYSCLK to output valid (5.5 V to 0.8 V—all except TS, ABB,
ARTRY, DBB)
11.0
3
14b
15
16
17
18
19
20
21
SYSCLK to output valid (all except TS, ABB, ARTRY, DBB)
SYSCLK to output invalid (output hold)
—
9.0
—
ns
ns
5
2
1.0
SYSCLK to output high impedance (all except ARTRY, ABB, DBB)
SYSCLK to ABB, DBB, high impedance after precharge
SYSCLK to ARTRY high impedance before precharge
SYSCLK to ARTRY precharge enable
—
8.0
1.0
7.5
—
ns
—
—
tsysclk
ns
4, 6
—
—
0.2 * tsysclk + 1.0
ns
2, 4, 7
4, 7
5, 7
Maximum delay to ARTRY precharge
—
—
1.0
2.0
tsysclk
tsysclk
SYSCLK to ARTRY high impedance after precharge
PID7t-603e Hardware Specifications, Rev. 5
10
Freescale Semiconductor
Electrical and Thermal Characteristics
1
Table 9. Output AC Timing Specifications (continued)
Vdd = AVdd = 2.5 5% V dc, OVdd = 3.3 ± 5%, GND = 0 V dc, 0 Tj 105 °C, C = 50 pF (unless otherwise noted)
L
200, 266, 300 MHz
Num
Characteristic
Unit
Note
Min
Max
Note:
1. All output specifications are measured from the 1.4 V of the rising edge of SYSCLK to the TTL level (0.8 V or 2.0 V) of the
signal in question. Both input and output timings are measured at the pin (see Figure 4).
2. This minimum parameter assumes C = 0 pF.
L
3. SYSCLK to output valid (5.5 V to 0.8 V) includes the extra delay associated with discharging the external voltage from 5.5 V
to 0.8 V instead of from Vdd to 0.8 V (5-V CMOS levels instead of 3.3-V CMOS levels).
4. tsysclk is the period of the external bus clock (SYSCLK) in nanoseconds (ns). The numbers given in the table must be multiplied
by the period of SYSCLK to compute the actual time duration (in nanoseconds) of the parameter in question.
5. Output signal transitions from GND to 2.0 V or Vdd to 0.8 V.
6. Nominal precharge width for ABB and DBB is 0.5 tsysclk
7. Nominal precharge width for ARTRY is 1.0 tsysclk
.
.
This figure provides the output timing diagram for the PID7t-603e.
VM
VM
VM
14
SYSCLK
15
16
12
ALL OUTPUTS
(Except TS, ABB,
DBB, ARTRY)
13
15
16
13
TS
17
ABB, DBB
21
20
19
18
ARTRY
VM = Midpoint Voltage (1.4 V)
Figure 4. Output Timing Diagram
4.3
JTAG AC Timing Specifications
This table provides the JTAG AC timing specifications as defined in Figure 5–Figure 8.
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
11
Electrical and Thermal Characteristics
Table 10. JTAG AC Timing Specifications
Vdd = AVdd = 2.5 ± 5% V dc, OVdd = 3.3 ± 5%, GND = 0 V dc, 0 Tj 105° C, CL = 50 pF
Num
Characteristic
Min
Max
Unit
Note
TCK frequency of operation
TCK cycle time
0
62.5
25
0
16
—
—
3
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
—
—
—
—
1
1
2
TCK clock pulse width measured at 1.4 V
TCK rise and fall times
3
4
TRST setup time to TCK rising edge
TRST assert time
13
40
6
—
—
—
—
25
24
—
—
24
15
5
—
2
6
Boundary scan input data setup time
Boundary scan input data hold time
TCK to output data valid
7
27
4
2
8
3
9
TCK to output high impedance
TMS, TDI data setup time
TMS, TDI data hold time
3
3
10
11
12
13
Note:
0
—
—
—
—
25
4
TCK to TDO data valid
TCK to TDO high impedance
3
1. TRST is an asynchronous signal. The setup time is for test purposes only.
2. Non-test signal input timing with respect to TCK.
3. Non-test signal output timing with respect to TCK.
This figure provides the JTAG clock input timing diagram.
1
2
2
VM
VM
VM
TCK
3
3
VM = Midpoint Voltage (1.4 V)
Figure 5. JTAG Clock Input Timing Diagram
PID7t-603e Hardware Specifications, Rev. 5
12
Freescale Semiconductor
Electrical and Thermal Characteristics
This figure provides the TRST timing diagram.
VM
TCK
4
TRST
5
Figure 6. TRST Timing Diagram
This figure provides the boundary-scan timing diagram.
VM
VM
7
TCK
6
Data Inputs
Input Data Valid
8
Data Outputs
Output Data Valid
9
8
Data Outputs
Data Outputs
Output Data Valid
Figure 7. Boundary-Scan Timing Diagram
This figure provides the test access port timing diagram.
VM
TCK
VM
11
10
TDI, TMS
Input Data Valid
12
TDO
Output Data Valid
13
TDO
12
TDO
Output Data Valid
Figure 8. Test Access Port Timing Diagram
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
13
Pin Assignments
5 Pin Assignments
Part A of Figure 9 shows the pinout of the CBGA package as viewed from the top surface. Part B shows
the side profile of the CBGA package to indicate the direction of the top surface view. The PBGA package
has an identical pinout. Part C shows the side profile of the PBGA package to indicate the direction of the
top surface view.
Part A
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
Not to Scale
Part B
View
Substrate Assembly
Encapsulant
Die
PID7t-603e Hardware Specifications, Rev. 5
14
Freescale Semiconductor
Pinout Listings
Part C
View
Substrate Assembly
Mold Compound
Die
Figure 9. Pinout of the CBGA and PBGA Packages as Viewed from the Top Surface
6 Pinout Listings
This table provides the pinout listing for the 603e CBGA and PBGA packages.
Table 11. Pinout Listing for the 255-Pin CBGA and PBGA Packages
Signal Name
A[0–31]
Pin Number
Active I/O
C16, E04, D13, F02, D14, G01, D15, E02, D16, D04, E13, GO2, E15, H01, E16, H02,
F13, J01, F14, J02, F15, H03, F16, F04, G13, K01, G15, K02, H16, M01, J15, P01
High
I/O
AACK
L02
Low
Low
High
Low
Low
—
I
I/O
I/O
O
I/O
—
I
ABB
K04
AP[0–3]
APE
C01, B04, B03, B02
A04
J04
ARTRY
AVDD
A10
L01
BG
Low
Low
Low
Low
Low
—
BR
B06
E01
D08
A06
D07
B01, B05
J14
O
O
I
CI
CKSTP_IN
CKSTP_OUT
CLK_OUT
CSE[0–1]
DBB
O
O
O
I/O
I
High
Low
Low
Low
Low
High
DBG
N01
H15
G04
DBDIS
DBWO
DH[0–31]
I
I
P14, T16, R15, T15, R13, R12, P11, N11, R11,T12, T11, R10, P09, N09, T10, R09, T09,
P08, N08, R08, T08, N07, R07, T07, P06, N06, R06, T06, R05, N05, T05, T04
I/O
DL[0–31]
K13, K15, K16, L16, L15, L13, L14, M16, M15, M13, N16, N15, N13, N14, P16, P15,
R16, R14, T14, N10, P13, N12, T13, P03, N03, N04, R03, T01, T02, P04, T03, R04
High
I/O
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
15
Pinout Listings
Table 11. Pinout Listing for the 255-Pin CBGA and PBGA Packages (continued)
Signal Name Pin Number
DP[0–7] M02, L03, N02, L04, R01, P02, M04, R02
Active I/O
High
Low
Low
Low
—
I/O
O
DPE
A05
G16
F01
DRTRY
GBL
I
I/O
—
GND
C05, C12, E03, E06, E08, E09, E11, E14, F05, F07, F10, F12, G06, G08, G09, G11,
H05, H07, H10, H12, J05, J07, J10, J12, K06, K08, K09, K11, L05, L07, L10, L12, M03,
M06, M08, M09, M11, M14, P05, P12
HRESET
A07
B15
D11
D12
B10
C13
Low
Low
—
I
I
INT
L1_TSTCLK 1
L2_TSTCLK 1
LSSD_MODE 1
MCP
I
—
I
Low
Low
—
I
I
NC (No-Connect) B07, B08, C03, C06, C08, D05, D06, H04, J16
—
—
OVDD
C07, E05, E07, E10, E12, G03, G05, G12, G14, K03, K05, K12, K14, M05, M07, M10,
—
M12, P07, P10
PLL_CFG[0–3]
QACK
QREQ
RSRV
SMI
A08, B09, A09, D09
High
Low
Low
Low
Low
Low
—
I
I
D03
J03
O
O
I
D01
A16
B14
C09
H14
C02
A14
A02, A03
C11
A11
A12
H13
C04
B11
C10
SRESET
SYSCLK
TA
I
I
Low
High
Low
High
—
I
TBEN
TBST
I
I/O
O
I
TC[0–1]
TCK
TDI
High
High
Low
Low
High
Low
I
TDO
O
I
TEA
TLBISYNC
TMS
I
I
TRST
I
PID7t-603e Hardware Specifications, Rev. 5
16
Freescale Semiconductor
Package Descriptions
Table 11. Pinout Listing for the 255-Pin CBGA and PBGA Packages (continued)
Signal Name Pin Number
TS
Active I/O
J13
Low
High
High
Low
—
I/O
O
TSIZ[0–2]
TT[0–4]
WT
A13, D10, B12
B13, A15, B16, C14, C15
D02
I/O
O
2
VDD
F06, F08, F09, F11, G07, G10, H06, H08, H09, H11, J06, J08, J09, J11, K07, K10, L06,
L08, L09, L11
—
VOLTDETGND 3
F03
Low
O
Note:
1. These are test signals for factory use only and must be pulled up to OVdd for normal machine operation.
2. OVdd inputs supply power to the I/O drivers and Vdd inputs supply power to the processor core.
3. NC (no-connect) in the PID6-603e; internally tied to GND in the PID7v-603e and PID7t-603e CBGA and PBGA package to
indicate to the power supply that a low-voltage processor is present.
7 Package Descriptions
The following sections provide the CBGA and PBGA package parameters and the mechanical dimensions
for the 603e.
7.1
CBGA Package Description
The following sections provide the package parameters and mechanical dimensions for the CBGA
package.
7.1.1
Package Parameters
The package parameters are as provided in the following list. The package type is 21 mm x 21 mm,
255-lead ceramic ball grid array (CBGA).
Package outline
Interconnects
Pitch
21 mm x 21 mm
255
1.27 mm (50 mil)
Package height
Minimum: 2.45 mm
Maximum: 3.00 mm
Ball diameter
0.89 mm (35 mil)
10 lbs
Maximum heat sink force
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
17
Package Descriptions
7.1.2
Mechanical Dimensions of the CBGA Package
This figure provides the mechanical dimensions and bottom surface nomenclature of the CBGA package.
2X
0.200
A
A1 CORNER
– E –
– T –
0.150 T
B
P
2X
NOTES:
0.200
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
N
– F –
MILLIMETERS
MIN MAX
INCHES
MIN MAX
DIM
A
B
C
D
G
H
K
N
P
21.000 BSC
21.000 BSC
0.827 BSC
0.827 BSC
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
2.450
3.000
0.930
0.097
0.118
0.036
0.820
0.790
0.032
0.031
K
1.270 BSC
0.050 BSC
0.990
0.039
H
C
0.635 BSC
0.025 BSC
5.000
5.000
16.000
16.000
0.197
0.197
0.630
0.630
G
K
255X
D
S
S
S
F
T E
T
0.300
0.150
S
Figure 10. Mechanical Dimensions and Bottom Surface Nomenclature of the CBGA Package
7.2
PBGA Package Description
The following sections provide the package parameters and mechanical dimensions.
7.2.1
Package Parameters
The package type is 23 mm x 23 mm, 255-lead plastic ball grid array (PBGA).
Package outline
23 mm x 23 mm
PID7t-603e Hardware Specifications, Rev. 5
18
Freescale Semiconductor
Package Descriptions
Interconnects
Pitch
255
1.27 mm (50 mil)
Package height
Ball diameter
Maximum heat sink force
Minimum: 2.1 mm; Maximum: 2.6 mm
0.76 mm (30 mil)
5 lbs
7.2.2
Mechanical Dimensions of the PBGA Package
This figure shows the non-JEDEC package mechanical dimensions and bottom surface nomenclature.
NOTES:
D
A
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. DIMENSIONS IN MILLIMETERS.
3. DIMENSION b IS MEASURED AT THE MAXIMUM
SOLDER BALL DIAMETER, PARALLEL TO PRIMARY
DATUM C.
256X
0.20 C
D2
0.35 C
4. PRIMARY DATUM C AND THE SEATING PLANE ARE
MILLIMETERS
DIM MIN
MAX
2.60
0.70
1.20
0.70
0.90
A
A1
A2
A3
b
2.10
0.50
1.10
0.50
0.60
E
E2
D
D1
23.00 BSC
19.05 REF
19.60
23.00 BSC
19.05 REF
D2 19.40
E
E1
4X
0.20
E2 19.40
19.60
e
1.27 BSC
A2
A3
TOP VIEW
(D1)
B
A1
A
15X
e
C
SEATING
PLANE
T
R
P
N
M
L
SIDE VIEW
15X
e
K
J
H
G
F
(E1)
4X e /2
E
D
C
B
A
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
256X
b
M
0.30
0.15
C A B
C
BOTTOM VIEW
M
Figure 11. Package Dimensions for the Plastic Ball Grid Array (PBGA)—non-JEDEC Standard
Note that Table 11 lists the pinout to this non-JEDEC standard in order to be consistent with the CBGA
pinout. This figure shows the JEDEC package dimensions of the PBGA package.
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
19
System Design Information
NOTES:
D
A
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. DIMENSIONS IN MILLIMETERS.
3. DIMENSION b IS MEASURED AT THE MAXIMUM
SOLDER BALL DIAMETER, PARALLEL TO PRIMARY
DATUM C.
256X
0.20 C
D2
0.35 C
4. PRIMARY DATUM C AND THE SEATING PLANE ARE
MILLIMETERS
DIM MIN
MAX
2.60
0.70
1.20
0.70
0.90
A
A1
A2
A3
b
2.10
0.50
1.10
0.50
0.60
E
E2
D
D1
23.00 BSC
19.05 REF
19.60
23.00 BSC
19.05 REF
D2 19.40
E
E1
4X
0.20
E2 19.40
19.60
e
1.27 BSC
A2
A3
TOP VIEW
(D1)
B
A1
A
15X
e
C
SEATING
PLANE
U
T
SIDE VIEW
R
P
N
M
L
15X
e
K
J
(E1)
H
G
F
4X e /2
E
D
C
B
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17
256X
b
M
0.30
0.15
C A B
C
BOTTOM VIEW
M
CASE 1167-01
Figure 12. Package Dimensions for the Plastic Ball Grid Array (PBGA)—JEDEC Standard
Note that the pin numberings shown in Figure 12 do not match Table 11; the pinout of the non-JEDEC
standard package (and the CBGA pinout) is shown in Figure 11. Note that Figure 11 should be used in
conjunction with Table 11 for the complete pinout description.
8 System Design Information
This section provides electrical and thermal design recommendations for successful application of 603e.
PID7t-603e Hardware Specifications, Rev. 5
20
Freescale Semiconductor
System Design Information
8.1
PLL Configuration
The 603e PLL is configured by the PLL_CFG[0–3] signals. For a given SYSCLK (bus) frequency, the
PLL configuration signals set the internal CPU and VCO frequency of operation. The PLL configuration
for the PID7t-603e is shown in this table for nominal frequencies.
Table 12. PLL Configuration
CPU Frequency in MHz (VCO Frequency in MHz)
PLL_CFG[0:3]
Bus-to-Core Core-to-VCO
Bus
Bus
Bus
Bus
Bus
Bus
Bus
Multiplier
Multiplier
25 MHz 33.33 MHz 40 MHz 50 MHz 60 MHz 66.67 MHz 75 MHz
0100
0101
0110
1000
1110
1010
0111
1011
1001
1101
2x
2x
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
150
(300)
2x
2.5x
3x
4x
2x
2x
2x
2x
2x
2x
2x
2x
804
(320)
100
(400)
120
(480)
133
(532)
150
(600)
—
—
—
—
150
(300)
166
(333)
187
(375)
150
(300)
180
(360)
200
(400)
225
(450)
3.5x
4x
175
(350)
210
(420)
233 (466)
267 (533)
300 (600)
—
263
(525)
160
(320)
200
(400)
240
(480)
300
(600)
4.5x
5x
150
(300)
180
(360)
225
(450)
270
(540)
—
—
—
—
166
(333)
200
(400)
250
(500)
300
(600)
5.5x
6x
183 (366)
220
(440)
275
(550)
—
—
150
200
240
300
—
—
(300)
(400)
(480)
(600)
0011
1111
PLL bypass
Clock off
Note:
1. Some PLL configurations may select bus, CPU, or VCO frequencies which are not supported; see Section 4.2.1, “Clock
AC Specifications,” for valid SYSCLK and VCO frequencies.
2. In PLL-bypass mode, the SYSCLK input signal clocks the internal processor directly, the PLL is disabled, and the bus
mode is set for 1:1 mode operation. This mode is intended for factory use only.
Note: The AC timing specifications given in this document do not apply in PLL-bypass mode.
3. In clock-off mode, no clocking occurs inside the 603e regardless of the SYSCLK input.
4. 80 MHz operation is not supported for the PBGA package (see Table 7).
8.2
PLL Power Supply Filtering
The AV power signal is provided on the 603e to provide power to the clock generation phase-locked
dd
loop. To ensure stability of the internal clock, the power supplied to the AV input signal should be filtered
dd
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
21
System Design Information
using a circuit similar to the one shown in Figure 13. The circuit should be placed as close as possible to
the AV pin to ensure it filters out as much noise as possible. The 0.1 µF capacitor should be closest to
dd
the AV pin, followed by the 10 µF capacitor, and finally the 10 resistor to V . These traces should be
dd
dd
kept short and direct.
10
V
AV
dd
dd
10 µF
0.1 µF
GND
Figure 13. PLL Power Supply Filter Circuit
8.3
Decoupling Recommendations
Due to the 603e’s dynamic power management feature, large address, data buses, and high-operating
frequencies, it can generate transient power surges and high-frequency noise in its power supply,
especially while driving large capacitive loads. This noise must be prevented from reaching other
components in the 603e system. It requires a clean, tightly regulated source of power. Therefore, it is
recommended that the system designer places at least one decoupling capacitor at each V and OV pin
dd
dd
of the 603e. It is also recommended that these decoupling capacitors receive their power from separate
V , OV , and GND power planes in the PCB, utilizing short traces to minimize inductance.
dd
dd
These capacitors should vary in value from 220 pF to 10 F to provide both high- and low-frequency
filtering, and should be placed as close as possible to their associated V or OV pin. Suggested values
dd
dd
for the V pins are: 220 pF (ceramic), 0.01 µF (ceramic), and 0.1 µF (ceramic). Suggested values for the
dd
OV pins are: 0.01 µF (ceramic), 0.1 µF (ceramic), and 10 µF (tantalum). Only SMT capacitors should
dd
be used to minimize lead inductance.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the V and OV planes, to enable quick recharging of the smaller chip capacitors. These bulk
dd
dd
capacitors should also have a low ESR (equivalent series resistance) rating to ensure the quick response
time necessary. They should also be connected to the power and ground planes through two vias to
minimize inductance. Suggested bulk capacitors—100 µF (AVX TPS tantalum) or 330 µF (AVX TPS
tantalum).
8.4
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unused active low inputs should be tied to V . Unused active high inputs should be connected to
dd
GND. All NC (no-connect) signals must remain unconnected. Power and ground connections must be
made to all external V , OV , and GND pins of the 603e.
dd
dd
PID7t-603e Hardware Specifications, Rev. 5
22
Freescale Semiconductor
System Design Information
8.5
Pull-up Resistor Requirements
The 603e requires high-resistive (weak: 10 K) pull-up resistors on several control signals of the bus
interface to maintain the control signals in the negated state after they have been actively negated and
released by the 603e or other bus master. These signals are: TS, ABB, DBB, and ARTRY.
In addition, the 603e has three open-drain style outputs that require pull-up resistors (weak or stronger:
4.7 K–10 K) if they are used by the system. These signals are: APE, DPE, and CKSTP_OUT.
During inactive periods on the bus, the address and transfer attributes on the bus are not driven by any
master and may float in the high-impedance state for relatively long periods of time. Since the 603e must
continually monitor these signals for snooping, this float condition may cause excessive power draw by
the input receivers on the 603e. It is recommended that these signals be pulled up through weak (10 K)
pull-up resistors or restored in some manner by the system. The snooped address and transfer attribute
inputs are—A[0–31], AP[0–3], TT[0–4], TBST, and GBL.
The data bus input receivers are normally turned off when no read operation is in progress and do not
require pull-up resistors on the data bus.
8.6
Thermal Management Information
This section provides thermal management information for the CBGA and PBGA packages for air-cooled
applications. Proper thermal control design is primarily dependent upon the system-level design—the heat
sink, airflow and thermal interface material.
This figure shows the upper and lower limits of the die junction-to-ambient thermal resistance for both
package styles. The lower limit is shown for the case of a densely populated PCB with high thermal
loading of adjacent and neighboring components.
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
23
System Design Information
.
40
35
30
25
20
15
10
5
Typical Upper Limit
Typical Low er Limit
0
0
0.5
1
1.5
2
Airflow Velocity (m / s)
Figure 14. Typical Die Junction-to-Ambient Thermal Resistance
(21 mm CBGA and 23 mm WB-PBGA)
To reduce the die-junction temperature, heat sinks may be attached to the package by several
methods—adhesive, spring clip to holes in the printed-circuit board or package, and mounting clip and
screw assembly (both CBGA and PGBA packages); see Figure 15.
CAUTION
While choosing a heat sink attachment method, any attachment mechanism should not degrade the
package structural integrity and/or the package-to-board interconnect reliability. For additional general
information, see this paper—Investigation of Heat Sink Attach Methodologies and the Effects on Package
Structural Integrity and Interconnect Reliability.
PID7t-603e Hardware Specifications, Rev. 5
24
Freescale Semiconductor
System Design Information
CBGA Package
Heat Sink
Heat Sink
Clip
Adhesive
or
Thermal Interface Material
Printed-Circuit Board
Option
PBGA Package
Heat Sink
Heat Sink
Clip
Adhesive
or
Thermal Interface Material
Printed-Circuit Board
Option
Figure 15. Package Exploded Cross-Sectional View with Heat Sink
The board designer can choose between several types of commercially available heat sinks to place on the
603e. Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal
performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost.
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
25
System Design Information
8.6.1
Internal Package Conduction Resistance
For this packaging technology, the intrinsic thermal conduction resistance (as shown in Table 3) versus the
external thermal resistance paths are shown in this figure for a package with an attached heat sink mounted
to a PCB.
External Resistance
Radiation
Convection
Heat Sink
Thermal Interface Material
Die/Package
Die Junction
Internal Resistance
Package/Leads
Printed-Circuit Board
Radiation
Convection
External Resistance
(Note the internal versus external package resistance)
Figure 16. Package with Heat Sink Mounted to a Printed-Circuit Board
8.6.2
Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the
thermal contact resistance. For those applications where the heat sink is attached by spring clip
mechanism, as shown in Figure 17. The thermal performance of three thin-sheet thermal-interface
materials (silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function
of contact pressure. As shown, the performance of these thermal interface materials improves with
increasing contact pressure. The use of thermal grease significantly reduces the interface thermal
resistance. That is, the bare joint results in a thermal resistance approximately seven times greater than the
thermal grease joint. Therefore, the synthetic grease offers the best thermal performance, considering the
low-interface pressure. Of course, the selection of any thermal interface material depends on many
factors—thermal performance requirements, manufacturability, service temperature, dielectric properties,
cost, etc.
PID7t-603e Hardware Specifications, Rev. 5
26
Freescale Semiconductor
System Design Information
Silicone Sheet (0.006 inch)
Bare Joint
2
Floroether Oil Sheet (0.007 inch)
Graphite/Oil Sheet (0.005 inch)
Synthetic Grease
1.5
1
0.5
0
0
10
20
30
Contact Pressure (psi)
Figure 17. Thermal Performance of Select Thermal Interface Material
40
50
60
70
80
The board designer can choose between several types of thermal interface. Heat sink adhesive materials
should be selected based upon high conductivity, yet adequate mechanical strength to meet equipment
shock/vibration requirements.
8.6.3
Heat Sink Selection Example
For preliminary heat sink sizing, the die-junction temperature can be expressed as follows:
T = T + T + ( + + ) * P
d
Eqn. 1
j
a
r
jc
int
sa
where:
T is the die-junction temperature
j
T is the inlet cabinet ambient temperature
a
T is the air temperature rise within the computer cabinet
r
is the die junction-to-case thermal resistance
jc
is the adhesive or interface material thermal resistance
int
is the heat sink base-to-ambient thermal resistance
sa
P is the power dissipated by the device
d
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
27
System Design Information
During operation the die-junction temperatures (T ) should be maintained less than the value specified in
j
Table 3. The temperature of the air cooling the component greatly depends upon the ambient inlet air
temperature and the air temperature rise within the electronic cabinet. An electronic cabinet inlet-air
temperature (T ) may range from 30 to 40 °C. The air temperature rise within a cabinet (T ) may be in the
a
r
range of 5 to 10 °C. The thermal resistance of the thermal interface material ( ) is typically about
int
1 °C/W. Assuming a T of 30 °C, a T of 5 °C a CBGA package = 0.095, and a power consumption (P )
a
r
jc
d
of 3.0 Watts, the following expression for T is obtained:
j
Die-junction temperature: T = 30 °C + 5 °C + (0.095 °C/W + 1.0 °C/W + R ) * 3.0 W. For example, the
j
sa
heat sink-to-ambient thermal resistance (R ) versus airflow velocity is shown in this figure.
sa
8
Example: Pin-fin Heat Sink
7
(25 x 28 x 15 mm)
6
5
4
3
2
1
0
0.5
1
1.5
Approach Air Velocity (m/s)
Figure 18. Example of Heat Sink-to-Ambient Thermal Resistance Versus Airflow Velocity
2
2.5
3
3.5
Assuming an air velocity of 0.5 m/s, we have an effective R of 7 °C/W, thus
sa
T = 30°C + 5°C + (0.095 °C/W +1.0 °C/W + 7 °C/W) * 3.0 W,
Eqn. 2
j
resulting in a die-junction temperature of approximately 60 °C which is well within the maximum
operating temperature of the component.
For a PBGA package, and assuming a T of 30 °C, a T of 5 °C a PBGA package = 8, and a power
a
r
jc
consumption (P ) of 3.0 Watts, the following expression for die-junction temperature, T , is obtained as:
d
j
T = 30 °C + 5 °C + (8 °C/W + 1.0 °C/W + R ) * 3.0 W
Eqn. 3
j
sa
Assuming an air velocity of 0.5 m/s, we have an effective R of 7 °C/W, thus
sa
PID7t-603e Hardware Specifications, Rev. 5
28
Freescale Semiconductor
Ordering Information
T = 30°C + 5°C + (8 °C/W +1.0 °C/W + 7 °C/W) * 3.0 W,
Eqn. 4
j
resulting in a die-junction temperature of approximately 83 °C that is well within the maximum operating
temperature of the component. Commercially available heat sinks have different heat sink-to-ambient
thermal resistances, and may or may not need air flow.
Though the die junction-to-ambient and the heat sink-to-ambient thermal resistances are a common
figure-of-merit used for comparing the thermal performance of various microelectronic packaging
technologies, one should exercise caution when only using this metric in determining thermal management
because no single parameter can adequately describe three-dimensional heat flow. The final die-junction
operating temperature is not only a function of the component-level thermal resistance, but the
system-level design and its operating conditions. In addition to the component’s power consumption, a
number of factors affect the final operating die-junction temperature—airflow, board population (local
heat flux of adjacent components), heat sink efficiency, heat sink attach, heat sink placement, next-level
interconnect technology, system air temperature rise, altitude, etc.
Due to the complexity and the many variations of system-level boundary conditions for today’s
microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation, convection,
and conduction) may vary widely. For these reasons, we recommend using conjugate heat transfer models
for the board, as well as, system-level designs. To expedite system-level thermal analysis, several
“compact” thermal-package models are available within FLOTHERM®. These are available upon
request.
9 Ordering Information
This figure provides the part numbering nomenclature for the PID7t-603e. Note that the individual part
numbers correspond to a maximum processor core frequency. For available frequencies, contact your local
Freescale sales office.
In addition to the processor frequency, the part numbering scheme also consists of a part modifier and
application modifier. The part modifier indicates any enhancement(s) in the part from the original design.
The application modifier may specify special bus frequencies or application conditions. Each part number
also contains a revision code. This refers to the die mask revision number and is specified in the part
numbering scheme for identification purposes only.
MPC 603 R RX XXX X X
Product Code
Part Identifier
Revision Level
(Contact Freescale Sales Office)
Application Modifier
Part Modifier
(L = Any Valid PLL Configuration)
(T = Extended Termperature Range)
Processor Frequency
(R = Remapped, Enhanced, Low-Voltage)
Package
(RX = CBGA without Lid)
(ZT = PBGA Package)
(VG = Polymer Core CBGA without Lid)
Figure 19. Part Number Key
PID7t-603e Hardware Specifications, Rev. 5
Freescale Semiconductor
29
Revision History
10 Revision History
This table summarizes revision history for this document.
Table 13. Document Revision History
Substantive Change(s)
• Updated to new Freescale template.
Rev. Number
Date
5
9/2011
• Added package info, VG = Polymer Core CBGA without Lid on Figure 19.
• Deleted thermal heat sink and thermal interface vendor details from 8.6/-23 and 8.6.2/-26.
PID7t-603e Hardware Specifications, Rev. 5
30
Freescale Semiconductor
How to Reach Us:
Home Page:
www.freescale.com
email:
support@freescale.com
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
1-800-521-6274
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
480-768-2130
support@freescale.com
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
support@freescale.com
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals” must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku
Tokyo 153-0064, Japan
0120 191014
+81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong
+800 2666 8080
Semiconductor was negligent regarding the design or manufacture of the part.
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor
Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447
Freescale, the Freescale logo, CodeWarrior, PowerQUICC, and StarCore are
trademarks of Freescale Semiconductor, Inc. Reg. U.S. Pat. & Tm. Off. QUICC Engine
is a trademark of Freescale Semiconductor, Inc. All other product or service names are
the property of their respective owners. The Power Architecture and Power.org word
marks and the Power and Power.org logos and related marks are trademarks and
service marks licensed by Power.org.
© 2011 Freescale Semiconductor, Inc.
303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor
@hibbertgroup.com
Document Number: MPC603E7TEC
Rev. 5
09/2011
相关型号:
MPC603RZT233LX
RISC Microprocessor, 32-Bit, 233MHz, CMOS, PBGA255, 23 X 23 MM, 2.60 MM HEIGHT, 1.27 MM PITCH, PLASTIC, BGA-255
MOTOROLA
MPC603RZT233TX
32-BIT, 233MHz, RISC PROCESSOR, PBGA255, 23 X 23 MM, 2.60 MM HEIGHT, 1.27 MM PITCH, PLASTIC, BGA-255
MOTOROLA
MPC603RZT266TX
RISC Microprocessor, 32-Bit, 266MHz, CMOS, PBGA255, 23 X 23 MM, 2.60 MM HEIGHT, 1.27 MM PITCH, PLASTIC, BGA-255
MOTOROLA
MPC603RZT300TA
32-BIT, 300MHz, RISC PROCESSOR, PBGA255, 23 X 23 MM, 2.60 MM HEIGHT, 1.27 MM PITCH, PLASTIC, BGA-255
MOTOROLA
©2020 ICPDF网 联系我们和版权申明