NX3L1G66GW-Q100H [NXP]
NX3L1G66-Q100 - Low-ohmic single-pole single-throw analog switch TSSOP 5-Pin;型号: | NX3L1G66GW-Q100H |
厂家: | NXP |
描述: | NX3L1G66-Q100 - Low-ohmic single-pole single-throw analog switch TSSOP 5-Pin 光电二极管 |
文件: | 总18页 (文件大小:186K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
Rev. 1 — 28 October 2013
Product data sheet
1. General description
The NX3L1G66-Q100 is a low-ohmic single-pole single-throw analog switch. It has two
input/output terminals (Y and Z) and an active HIGH enable input pin (E). When E is LOW,
the analog switch is turned off.
Schmitt trigger action at the enable input (E) makes the circuit tolerant to slower input rise
and fall times. The NX3L1G66-Q100 allows signals with amplitude up to VCC to be
transmitted from Y to Z; or from Z to Y. Its low ON resistance (0.5 ) and flatness (0.13 )
ensures minimal attenuation and distortion of transmitted signals.
This product has been qualified to the Automotive Electronics Council (AEC) standard
Q100 (Grade 1) and is suitable for use in automotive applications.
2. Features and benefits
Automotive product qualification in accordance with AEC-Q100 (Grade 1)
Specified from 40 C to +85 C and from 40 C to +125 C
Wide supply voltage range from 1.4 V to 4.3 V
Very low ON resistance (peak):
1.6 (typical) at VCC = 1.4 V
1.0 (typical) at VCC = 1.65 V
0.55 (typical) at VCC = 2.3 V
0.50 (typical) at VCC = 2.7 V
0.50 (typical) at VCC = 4.3 V
High noise immunity
ESD protection:
MIL-STD-883, method 3015 Class 3A exceeds 7500 V
HBM JESD22-A114F Class 3A exceeds 7500 V
MM JESD22-A115-A exceeds 200 V (C = 200 pF, R = 0 )
CDM AEC-Q100-011 revision B exceeds 1000 V
IEC61000-4-2 contact discharge exceeds 4000 V for switch ports
CMOS low-power consumption
Latch-up performance exceeds 100 mA per JESD 78 Class II Level A
Direct interface with TTL levels at 3.0 V
Control input accepts voltages above supply voltage
High current handling capability (350 mA continuous current under 3.3 V supply)
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
3. Applications
Cell phone
PDA
Portable media player
4. Ordering information
Table 1.
Ordering information
Type number
Package
Temperature range Name
Description
Version
NX3L1G66GW-Q100 40 C to +125 C
TSSOP5 plastic thin shrink small outline package; 5 leads;
body width 1.25 mm
SOT353-1
5. Marking
Table 2.
Marking codes[1]
Type number
Marking code
NX3L1G66GW-Q100
DL
[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.
6. Functional diagram
Y
Z
E
Z
Y
E
001aag487
001aah372
Fig 1. Logic symbol
Fig 2. Logic diagram
7. Pinning information
7.1 Pinning
1;ꢀ/ꢁ*ꢂꢂꢃ4ꢁꢄꢄ
ꢀ
ꢁ
ꢂ
ꢃ
<
=
9
(
&&
ꢄ
*1'
DDDꢀꢁꢁꢂꢃꢄꢁ
Fig 3. Pin configuration SOT353-1 (TSSOP5)
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
2 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
7.2 Pin description
Table 3.
Symbol
Y
Pin description
Pin
1
Description
independent input or output
independent output or input
ground (0 V)
Z
2
GND
E
3
4
enable input (active HIGH)
not connected
n.c.
-
VCC
5
supply voltage
8. Functional description
Table 4.
Function table[1]
Input E
Switch
L
OFF-state
ON-state
H
[1] H = HIGH voltage level; L = LOW voltage level.
9. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
VCC
VI
Parameter
Conditions
enable input E
VI < 0.5 V
Min
0.5
0.5
0.5
50
-
Max
+4.6
+4.6
Unit
V
supply voltage
input voltage
[1]
[2]
V
VSW
IIK
switch voltage
input clamping current
VCC + 0.5 V
-
mA
ISK
switch clamping current VI < 0.5 V or VI > VCC + 0.5 V
50
350
mA
mA
ISW
switch current
VSW > 0.5 V or VSW < VCC + 0.5 V;
-
source or sink current
VSW > 0.5 V or VSW < VCC + 0.5 V;
pulsed at 1 ms duration, < 10 % duty cycle;
peak current
-
500
mA
Tstg
Ptot
storage temperature
total power dissipation
65
+150
250
C
[3]
Tamb = 40 C to +125 C
-
mW
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
[3] For TSSOP5 package: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K.
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
3 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
10. Recommended operating conditions
Table 6.
Recommended operating conditions
Symbol Parameter
Conditions
Min
1.4
0
Max
4.3
Unit
V
VCC
VI
supply voltage
input voltage
enable input E
4.3
V
[1]
[2]
VSW
Tamb
t/V
switch voltage
0
VCC
+125
200
V
ambient temperature
input transition rise and fall rate
40
-
C
ns/V
VCC = 1.4 V to 4.3 V
[1] To avoid sinking GND current from terminal Z when switch current flows in terminal Y, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current flows from terminal Y. In this case, there is no limit for
the voltage drop across the switch.
[2] Applies to control signal levels.
11. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
Tamb = 25 C
Tamb = 40 C to +125 C Unit
Min
Typ
Max
Min
Max
Max
(85 C) (125 C)
VIH
HIGH-level
input voltage
VCC = 1.4 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
VCC = 1.4 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
0.65VCC
-
-
-
-
-
-
-
-
-
-
0.65VCC
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
A
1.7
-
1.7
2.0
-
2.0
0.7VCC
-
0.35VCC
0.7
0.7VCC
VIL
LOW-level
input voltage
-
-
-
-
-
-
-
-
-
-
0.35VCC 0.35VCC
0.7
0.8
0.7
0.8
0.8
0.3VCC
-
0.3VCC 0.3VCC
II
input leakage enable input E;
0.5
1
current
VI = GND to 4.3 V;
VCC = 1.4 V to 4.3 V
IS(OFF)
OFF-state
leakage
current
Y port; see Figure 4
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
Z port; see Figure 5
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
5
-
-
50
50
500 nA
500 nA
10
IS(ON)
ON-state
leakage
current
-
-
-
-
5
-
-
50
50
500 nA
500 nA
10
ICC
supply current VI = VCC or GND;
VSW = GND or VCC
VCC = 3.6 V
VCC = 4.3 V
-
-
-
-
100
150
-
-
690
800
6000 nA
7000 nA
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
4 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
Tamb = 25 C
Tamb = 40 C to +125 C Unit
Min
Typ
Max
Min
Max
Max
(85 C) (125 C)
CI
input
capacitance
-
-
-
1.0
35
-
-
-
-
-
-
-
-
-
-
-
-
pF
pF
pF
CS(OFF) OFF-state
capacitance
CS(ON)
ON-state
110
capacitance
11.1 Test circuits
V
CC
V
CC
nE
nZ
nE
nZ
V
V
IH
IL
nY
nY
I
I
S
S
GND
GND
V
V
V
V
O
I
O
I
001aag488
001aag489
VI = 0.3 V or VCC 0.3 V; VO = VCC 0.3 V or 0.3 V.
VI = 0.3 V or VCC 0.3 V; VO = open circuit.
Fig 4. Test circuit for measuring OFF-state leakage
current
Fig 5. Test circuit for measuring ON-state leakage
current
11.2 ON resistance
Table 8.
ON resistance
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 7 to Figure 13.
Symbol Parameter Conditions Tamb = 40 C to +85 C Tamb = 40 C to +125 C Unit
Min
Typ[1]
Max
Min
Max
RON(peak) ON resistance VI = GND to VCC
;
(peak)
I
SW = 100 mA; see Figure 6
VCC = 1.4 V
-
-
-
-
-
1.6
1.0
3.7
1.6
-
-
-
-
-
4.1
1.7
0.9
0.9
0.9
VCC = 1.65 V
VCC = 2.3 V
0.55
0.5
0.8
VCC = 2.7 V
0.75
0.75
VCC = 4.3 V
0.5
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
5 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
Table 8.
ON resistance …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 7 to Figure 13.
Symbol Parameter Conditions Tamb = 40 C to +85 C Tamb = 40 C to +125 C Unit
Min
Typ[1]
Max
Min
Max
[2]
RON(flat)
ON resistance VI = GND to VCC;
(flatness)
ISW = 100 mA
VCC = 1.4 V
VCC = 1.65 V
VCC = 2.3 V
VCC = 2.7 V
VCC = 4.3 V
-
-
-
-
-
1.0
0.5
3.3
1.2
0.3
0.3
0.4
-
-
-
-
-
3.6
1.3
0.15
0.13
0.2
0.35
0.35
0.45
[1] Typical values are measured at Tamb = 25 C.
[2] Flatness is defined as the difference between the maximum and minimum value of ON resistance measured at identical VCC and
temperature.
11.3 ON resistance test circuit and graphs
001aag564
1.6
R
ON
(Ω)
1.2
V
SW
(1)
0.8
0.4
0
V
CC
(2)
E
Z
V
IH
(3)
(4)
(5)
Y
(6)
GND
V
I
I
SW
0
1
2
3
4
5
V (V)
I
001aah375
RON = VSW / ISW
.
(1) VCC = 1.5 V.
(2) VCC = 1.8 V.
(3) VCC = 2.5 V.
(4)
VCC = 2.7 V.
(5) VCC = 3.3 V.
(6) VCC = 4.3 V.
Measured at Tamb = 25 C.
Fig 6. Test circuit for measuring ON resistance
Fig 7. Typical ON resistance as a function of input
voltage
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
6 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
001aag565
001aag566
1.6
1.0
R
(Ω)
ON
R
(Ω)
ON
0.8
1.2
(1)
(2)
(3)
(4)
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
0.8
0.4
0
0
1
2
3
0
1
2
3
V (V)
I
V (V)
I
(1) Tamb = 125 C.
(2) amb = 85 C.
(1) Tamb = 125 C.
(2) amb = 85 C.
T
T
(3) Tamb = 25 C.
(4) Tamb = 40 C.
(3) Tamb = 25 C.
(4) Tamb = 40 C.
Fig 8. ON resistance as a function of input voltage;
VCC = 1.5 V
Fig 9. ON resistance as a function of input voltage;
VCC = 1.8 V
001aag567
001aag568
1.0
1.0
R
ON
R
ON
(Ω)
(Ω)
0.8
0.8
0.6
0.4
0.2
0
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
0
1
2
3
0
1
2
3
V (V)
V (V)
I
I
(1) Tamb = 125 C.
(2) amb = 85 C.
(1) Tamb = 125 C.
(2) amb = 85 C.
T
T
(3) Tamb = 25 C.
(4) Tamb = 40 C.
(3) Tamb = 25 C.
(4) Tamb = 40 C.
Fig 10. ON resistance as a function of input voltage;
VCC = 2.5 V
Fig 11. ON resistance as a function of input voltage;
VCC = 2.7 V
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
7 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
001aag569
001aaj896
1.0
1.0
R
ON
R
ON
(Ω)
(Ω)
0.8
0.8
(1)
(2)
(3)
(4)
0.6
0.4
0.2
0
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
0
1
2
3
4
0
1
2
3
4
5
V (V)
I
V (V)
I
(1) Tamb = 125 C.
(2) amb = 85 C.
(1) Tamb = 125 C.
(2) amb = 85 C.
T
T
(3) Tamb = 25 C.
(4) Tamb = 40 C.
(3) Tamb = 25 C.
(4) Tamb = 40 C.
Fig 12. ON resistance as a function of input voltage;
VCC = 3.3 V
Fig 13. ON resistance as a function of input voltage;
VCC = 4.3 V
12. Dynamic characteristics
Table 9.
Dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit, see Figure 15.
Symbol Parameter
Conditions
Tamb = 25 C
Tamb = 40 C to +125 C Unit
Min Typ[1] Max
Min
Max
Max
(85 C) (125 C)
ten
enable time
E to Z or Y; see Figure 14
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
E to Z or Y; see Figure 14
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
-
27
22
17
14
14
41
33
26
23
23
-
-
-
-
-
43
34
27
24
24
48
36
30
26
26
ns
ns
ns
ns
ns
tdis
disable time
-
-
-
-
-
9
7
4
4
4
18
13
8
-
-
-
-
-
19
15
9
21
16
10
9
ns
ns
ns
ns
ns
8
8
8
8
9
[1] Typical values are measured at Tamb = 25 C and VCC = 1.5 V, 1.8 V, 2.5 V, 3.3 V and 4.3 V respectively.
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
8 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
12.1 Waveform and test circuits
V
I
E input
V
M
GND
t
t
en
dis
V
OH
V
V
X
X
Y output
OFF to HIGH
HIGH to OFF
GND
switch
switch
switch
disabled
enabled
disabled
001aah875
Measurement points are given in Table 10.
Logic level: VOH is the typical output voltage that occurs with the output load.
Fig 14. Enable and disable times
Table 10. Measurement points
Supply voltage
VCC
Input
VM
Output
VX
1.4 V to 4.3 V
0.5VCC
0.9VOH
V
CC
E
Y/Z
Z/Y
G
C
L
V
V
V
R
L
V
EXT
= 1.5 V
I
O
001aah377
Test data is given in Table 11.
Definitions test circuit:
RL = Load resistance.
CL = Load capacitance including jig and probe capacitance.
EXT = External voltage for measuring switching times.
V
Fig 15. Load circuit for switching times
Table 11. Test data
Supply voltage
VCC
Input
Load
CL
VI
tr, tf
2.5 ns
RL
1.4 V to 4.3 V
VCC
35 pF
50
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
9 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
12.2 Additional dynamic characteristics
Table 12. Additional dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise
specified); tr = tf 2.5 ns.
Symbol Parameter
Conditions
Tamb = 25 C
Unit
Min
Typ
Max
[1]
THD
total harmonic
distortion
fi = 20 Hz to 20 kHz; RL = 32 ; see Figure 16
VCC = 1.4 V; VI = 1 V (p-p)
VCC = 1.65 V; VI = 1.2 V (p-p)
VCC = 2.3 V; VI = 1.5 V (p-p)
VCC = 2.7 V; VI = 2 V (p-p)
VCC = 4.3 V; VI = 2 V (p-p)
RL = 50 ; see Figure 17
-
-
-
-
-
0.15
0.10
0.02
0.02
0.02
-
-
-
-
-
%
%
%
%
%
[1]
[1]
f(3dB)
3 dB frequency
response
VCC = 1.4 V to 4.3 V
-
-
60
-
-
MHz
dB
iso
isolation (OFF-state)
crosstalk voltage
fi = 100 kHz; RL = 50 ; see Figure 18
VCC = 1.4 V to 4.3 V
90
Vct
between digital inputs and switch;
fi = 1 MHz; CL = 50 pF; RL = 50 ; see Figure 19
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
0.2
0.2
-
-
V
V
Qinj
charge injection
fi = 1 MHz; CL = 0.1 nF; RL = 1 M; Vgen = 0 V;
Rgen = 0 ; see Figure 20
VCC = 1.5 V
VCC = 1.8 V
VCC = 2.5 V
VCC = 3.3 V
VCC = 4.3 V
-
-
-
-
-
3
3
3
3
6
-
-
-
-
-
pC
pC
pC
pC
pC
[1] fi is biased at 0.5VCC
.
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
10 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
12.3 Test circuits
V
0.5V
CC
CC
E
V
R
L
IH
Y/Z
Z/Y
f
D
i
001aah378
Fig 16. Test circuit for measuring total harmonic distortion
V
0.5V
CC
CC
E
V
R
L
IH
Y/Z
Z/Y
f
dB
i
001aah379
To obtain 0 dBm level at output, adjust fi voltage. Increase fi frequency until dB meter reads 3 dB.
Fig 17. Test circuit for measuring the frequency response when channel is in ON-state
0.5V
V
0.5V
CC
R
CC
CC
R
E
V
IL
L
L
Y/Z
Z/Y
f
dB
i
001aah380
To obtain 0 dBm level at input, adjust fi voltage.
Fig 18. Test circuit for measuring isolation (OFF-state)
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
11 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
V
CC
E
Y/Z
Z/Y
G
V
R
L
R
L
C
L
V
V
O
I
0.5V
0.5V
CC
CC
001aah383
a. Test circuit
logic
input (E)
off
on
off
V
O
V
ct
001aah381
b. Input and output pulse definitions
Fig 19. Test circuit for measuring crosstalk voltage between digital inputs and switch
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
12 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
V
CC
E
R
gen
Y/Z
Z/Y
G
C
L
V
V
V
R
L
V
gen
I
O
GND
001aah385
a. Test circuit
logic
input (E)
off
on
off
V
O
V
O
001aah384
b. Input and output pulse definitions
Definition: Qinj = VO CL.
VO = output voltage variation.
Rgen = generator resistance.
V
gen = generator voltage.
Fig 20. Test circuit for measuring charge injection
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
13 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
13. Package outline
TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm
SOT353-1
D
E
A
X
c
y
H
v
M
A
E
Z
5
4
A
2
A
(A )
3
A
1
θ
L
L
p
1
3
e
w M
b
p
detail X
e
1
0
1.5
3 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(1)
(1)
A
A
A
b
c
D
E
e
e
1
H
L
L
p
UNIT
v
w
y
Z
θ
1
2
3
p
E
max.
0.1
0
1.0
0.8
0.30
0.15
0.25
0.08
2.25
1.85
1.35
1.15
2.25
2.0
0.46
0.21
0.60
0.15
7°
0°
mm
1.1
0.65
1.3
0.15
0.425
0.3
0.1
0.1
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
00-09-01
03-02-19
SOT353-1
MO-203
SC-88A
Fig 21. Package outline SOT353-1 (TSSOP5)
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
14 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
14. Abbreviations
Table 13. Abbreviations
Acronym
CDM
CMOS
ESD
Description
Charged-Device Model
Complementary Metal-Oxide Semiconductor
ElectroStatic Discharge
Human Body Model
HBM
MIL
Military
MM
Machine Model
PDA
Personal Digital Assistant
Transistor-Transistor Logic
TTL
15. Revision history
Table 14. Revision history
Document ID
Release date
20131028
Data sheet status
Change notice
Supersedes
NX3L1G66_Q100 v.1
Product data sheet
-
-
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
15 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
Suitability for use in automotive applications — This NXP
16.2 Definitions
Semiconductors product has been qualified for use in automotive
applications. Unless otherwise agreed in writing, the product is not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer's own
risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
16 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
NX3L1G66_Q100
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 1 — 28 October 2013
17 of 18
NXP Semiconductors
NX3L1G66-Q100
Low-ohmic single-pole single-throw analog switch
18. Contents
1
2
3
4
5
6
General description. . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
7
7.1
7.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 2
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
8
Functional description . . . . . . . . . . . . . . . . . . . 3
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3
Recommended operating conditions. . . . . . . . 4
9
10
11
Static characteristics. . . . . . . . . . . . . . . . . . . . . 4
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ON resistance. . . . . . . . . . . . . . . . . . . . . . . . . . 5
ON resistance test circuit and graphs. . . . . . . . 6
11.1
11.2
11.3
12
Dynamic characteristics . . . . . . . . . . . . . . . . . . 8
Waveform and test circuits . . . . . . . . . . . . . . . . 9
Additional dynamic characteristics . . . . . . . . . 10
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
12.1
12.2
12.3
13
14
15
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 14
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 15
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 15
16
Legal information. . . . . . . . . . . . . . . . . . . . . . . 16
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 16
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
16.1
16.2
16.3
16.4
17
18
Contact information. . . . . . . . . . . . . . . . . . . . . 17
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2013.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 28 October 2013
Document identifier: NX3L1G66_Q100
相关型号:
©2020 ICPDF网 联系我们和版权申明