NX3L2467 [NXP]
Dual low-ohmic double-pole double-throw analog switch; 双低电阻双刀双掷模拟开关型号: | NX3L2467 |
厂家: | NXP |
描述: | Dual low-ohmic double-pole double-throw analog switch |
文件: | 总24页 (文件大小:225K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NX3L2467
Dual low-ohmic double-pole double-throw analog switch
Rev. 3 — 29 December 2010
Product data sheet
1. General description
The NX3L2467 is a dual low-ohmic double-pole double-throw analog switch suitable for
use as an analog or digital multiplexer/demultiplexer. It consists of four switches, each
with two independent input/outputs (nY0 and nY1) and a common input/output (nZ). The
two digital inputs (1S and 2S) are used to select the switch position. 1S is used in
selecting the independent inputs/outputs switched to 1Z and 2Z, and 2S is used in
selecting the independent inputs/outputs switched to 3Z and 4Z. Schmitt trigger action at
the digital inputs makes the circuit tolerant to slower input rise and fall times. Low
threshold digital inputs allows this device to be driven by 1.8 V logic levels in 3.3 V
applications without significant increase in supply current ICC. This makes it possible for
the NX3L467 to switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for
logic level translation. The NX3L2467 allows signals with amplitude up to VCC to be
transmitted from nZ to nY0 or nY1; or from nY0 or nY1 to nZ. Its low ON resistance (0.5 )
and flatness (0.13 ) ensures minimal attenuation and distortion of transmitted signals.
2. Features and benefits
Wide supply voltage range from 1.4 V to 4.3 V
Very low ON resistance (peak):
1.7 (typical) at VCC = 1.4 V
1.0 (typical) at VCC = 1.65 V
0.6 (typical) at VCC = 2.3 V
0.5 (typical) at VCC = 2.7 V
0.5 (typical) at VCC = 4.3 V
Break-before-make switching
High noise immunity
ESD protection:
HBM JESD22-A114F Class 3A exceeds 4000 V
MM JESD22-A115-A exceeds 200 V
CDM AEC-Q100-011 revision B exceeds 1000 V
IEC61000-4-2 contact discharge exceeds 6000 V for switch ports
CMOS low-power consumption
Latch-up performance exceeds 100 mA per JESD 78B Class II Level A
1.8 V control logic at VCC = 3.6 V
Control input accepts voltages above supply voltage
Very low supply current, even when input is below VCC
High current handling capability (350 mA continuous current under 3.3 V supply)
Specified from 40 C to +85 C and from 40 C to +125 C
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
3. Applications
Cell phone
PDA
Portable media player
4. Ordering information
Table 1.
Ordering information
Type number Package
Temperature range Name
Description
Version
NX3L2467PW 40 C to +125 C
TSSOP16
plastic thin shrink small outline package; 16 leads;
body width 4.4 mm
SOT403-1
NX3L2467HR 40 C to +125 C
HXQFN16U plastic thermal enhanced extremely thin quad flat
package; no leads; 16 terminals; UTLP based;
body 3 3 0.5 mm
SOT1039-1
SOT1161-1
NX3L2467GU 40 C to +125 C
XQFN16
plastic, extremely thin quad flat package; no leads;
16 terminals; body 1.80 2.60 0.50 mm
5. Marking
Table 2.
Marking codes
Type number
NX3L2467PW
NX3L2467HR
NX3L2467GU
Marking code
X3L2467
D67
D67
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
2 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
6. Functional diagram
1Y1
1Z
1Y0
1Z
1Y1
1Y0
1S
2Y0
2Z
2Y1
1S
2Y1
3Y0
3Z
3Y1
2Z
4Y0
4Z
4Y1
2S
2Y0
001aak174
001aak175
Fig 1. Logic symbol
Fig 2. Logic diagram
7. Pinning information
7.1 Pinning
terminal 1
index area
NX3L2467
1Y0
1S
1
2
3
4
12 4Z
11 4Y1
10 2S
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1Y1
1Z
V
CC
NX3L2467
4Y0
4Z
2Y1
2Z
1Y0
1S
4Y1
2S
9
3Y0
2Y1
2Z
3Y0
3Z
2Y0
GND
3Y1
001aak176
Transparent top view
001aak177
Fig 3. Pin configuration SOT403-1 (TSSOP16)
Fig 4. Pin configuration SOT1039-1 (HXQFN16U)
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
3 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
terminal 1
index area
1Y0
1
2
3
4
12 4Z
1S
2Y1
2Z
11 4Y1
NX3L2467
10 2S
9
3Y0
001aam031
Transparent top view
Fig 5. Pin configuration SOT1161-1 (XQFN16)
7.2 Pin description
Table 3.
Symbol
Pin description
Pin
Description
SOT1039-1 and SOT1161-1
SOT403-1
3, 7, 11, 15
4, 12
1Y0, 2Y0, 3Y0, 4Y0
1S, 2S
1, 5, 9, 13
2, 10
independent input or output
select input
1Y1, 2Y1, 3Y1, 4Y1
1Z, 2Z, 3Z, 4Z
GND
15, 3, 7, 11
16, 4, 8, 12
6
1, 5, 9, 13
2, 6, 10, 14
8
independent input or output
common output or input
ground (0 V)
VCC
14
16
supply voltage
8. Functional description
Table 4.
Function table[1]
Input nS
Channel on
nY0
L
H
nY1
[1] H = HIGH voltage level; L = LOW voltage level.
9. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
VCC
Parameter
Conditions
Min
0.5
0.5
0.5
Max
+4.6
+4.6
Unit
V
supply voltage
input voltage
switch voltage
[1]
[2]
VI
select input nS
V
VSW
VCC + 0.5 V
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
4 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
Table 5.
Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
IIK
Parameter
Conditions
Min
Max
-
Unit
mA
mA
mA
input clamping current
VI < 0.5 V
50
ISK
switch clamping current VI < 0.5 V or VI > VCC + 0.5 V
-
-
50
350
ISW
switch current
VSW > 0.5 V or VSW < VCC + 0.5 V;
source or sink current
VSW > 0.5 V or VSW < VCC + 0.5 V;
pulsed at 1 ms duration, < 10 % duty cycle;
peak current
-
500
mA
Tstg
Ptot
storage temperature
total power dissipation
65
+150
C
Tamb = 40 C to +125 C
TSSOP16
[3]
[4]
[5]
-
-
-
500
250
250
mW
mW
mW
HXQFN16U
XQFN16
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
[3] For TSSOP16 package: above 60 C the value of Ptot derates linearly with 5.5 mW/K above.
[4] For HXQFN16U package: above 135 C the value of Ptot derates linearly with 16.9 mW/K.
[5] For XQFN16 package: above 133 C the value of Ptot derates linearly with 14.5 mW/K.
10. Recommended operating conditions
Table 6.
Recommended operating conditions
Symbol Parameter
Conditions
Min
1.4
0
Max
4.3
Unit
V
VCC
VI
supply voltage
input voltage
select input nS
4.3
V
[1]
[2]
VSW
Tamb
t/V
switch voltage
0
VCC
+125
200
V
ambient temperature
input transition rise and fall rate
40
-
C
ns/V
VCC = 1.4 V to 4.3 V
[1] To avoid sinking GND current from terminal nZ when switch current flows in terminal nYn, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no GND current will flow from terminal nYn. In this case, there
is no limit for the voltage drop across the switch.
[2] Applies to control signal levels.
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
5 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
11. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
Tamb = 25 C
Tamb = 40 C to +125 C Unit
Min
Typ
Max
Min
Max
Max
(85 C) (125 C)
VIH
HIGH-level
input voltage
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
0.9
0.9
1.1
1.3
1.4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.9
0.9
1.1
1.3
1.4
-
-
-
-
-
V
V
V
V
V
V
V
V
V
V
A
-
-
-
-
-
-
-
-
-
VIL
LOW-level
input voltage
0.3
0.4
0.4
0.5
0.6
-
0.3
0.4
0.4
0.5
0.6
0.5
0.3
0.3
0.4
0.5
0.6
1
-
-
-
-
-
-
-
-
II
input leakage select input nS;
-
-
current
VI = GND to 4.3 V;
VCC = 1.4 V to 4.3 V
IS(OFF)
OFF-state
leakage
current
nY0 and nY1 port;
see Figure 6
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
5
-
-
50
50
500 nA
500 nA
10
IS(ON)
ON-state
leakage
current
nZ port;
VCC = 1.4 V to 3.6 V;
see Figure 7
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
5
-
-
50
50
500 nA
500 nA
10
ICC
supply current VI = VCC or GND;
VSW = GND or VCC
VCC = 3.6 V
VCC = 4.3 V
-
-
-
-
100
150
-
-
500
800
5000 nA
6000 nA
ICC
additional
supply current
VSW = GND or VCC
VI = 2.6 V; VCC = 4.3 V
VI = 2.6 V; VCC = 3.6 V
VI = 1.8 V; VCC = 4.3 V
VI = 1.8 V; VCC = 3.6 V
VI = 1.8 V; VCC = 2.5 V
-
-
-
-
-
-
2.0
0.35
7.0
2.5
50
4.0
0.7
10.0
4.0
200
-
-
-
-
-
-
-
7
1
7
1
A
A
A
A
nA
pF
15
5
15
5
300
-
500
-
CI
input
1.0
capacitance
CS(OFF) OFF-state
capacitance
-
-
35
-
-
-
-
-
-
-
-
pF
pF
CS(ON)
ON-state
130
capacitance
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
6 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
11.1 Test circuits
switch nS
V
CC
1
2
V
IH
V
IL
nS
nZ
nY0
nY1
1
2
V
IL
or V
IH
switch
I
S
V
V
O
I
GND
012aaa000
VI = 0.3 V or VCC 0.3 V; VO = VCC 0.3 V or 0.3 V.
Fig 6. Test circuit for measuring OFF-state leakage current
switch nS
V
CC
1
2
V
IH
V
IL
nS
nZ
nY0
nY1
1
2
V
IL
or V
IH
switch
I
S
V
V
I
O
GND
012aaa001
VI = 0.3 V or VCC 0.3 V; VO = VCC 0.3 V or 0.3 V.
Fig 7. Test circuit for measuring ON-state leakage current
11.2 ON resistance
Table 8.
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 9 to Figure 15.
ON resistance[1]
Symbol Parameter Conditions Tamb = 40 C to +85 C Tamb = 40 C to +125 C Unit
Min
Typ[2]
Max
Min
Max
RON(peak) ON resistance VI = GND to VCC
;
(peak)
ISW = 100 mA; see Figure 8
VCC = 1.4 V
-
-
-
-
-
1.7
1.0
0.6
0.5
0.5
3.7
1.6
-
-
-
-
-
4.1
1.7
0.9
0.9
0.9
VCC = 1.65 V
VCC = 2.3 V
0.8
VCC = 2.7 V
0.75
0.75
VCC = 4.3 V
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
7 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
Table 8.
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 9 to Figure 15.
ON resistance[1]
Symbol Parameter Conditions Tamb = 40 C to +85 C Tamb = 40 C to +125 C Unit
Min
Typ[2]
Max
Min
Max
[3]
RON
ON resistance VI = GND to VCC;
mismatch
between
channels
ISW = 100 mA
VCC = 1.4 V; VSW = 0.4 V
VCC = 1.65 V; VSW = 0.5 V
VCC = 2.3 V; VSW = 0.7 V
VCC = 2.7 V; VSW = 0.8 V
VCC = 4.3 V; VSW = 0.8 V
-
-
-
-
-
0.18
0.18
0.07
0.07
0.07
0.3
0.2
0.1
0.1
0.1
-
-
-
-
-
0.3
0.3
0.13
0.13
0.13
[4]
RON(flat)
ON resistance VI = GND to VCC;
(flatness)
I
SW = 100 mA
VCC = 1.4 V
VCC = 1.65 V
VCC = 2.3 V
VCC = 2.7 V
VCC = 4.3 V
-
-
-
-
-
1.0
0.5
3.3
1.2
0.3
0.3
0.4
-
-
-
-
-
3.6
1.3
0.15
0.13
0.2
0.35
0.35
0.45
[1] For NX3L2467PW (TSSOP16 package), all ON resistance values are up to 0.05 higher.
[2] Typical values are measured at Tamb = 25 C.
[3] Measured at identical VCC, temperature and input voltage.
[4] Flatness is defined as the difference between the maximum and minimum value of ON resistance measured at identical VCC and
temperature.
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
8 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
11.3 ON resistance test circuit and graphs
001aag564
1.6
R
ON
(Ω)
1.2
(1)
V
SW
V
0.8
0.4
0
switch nS
(2)
V
CC
1
2
V
V
IL
(3)
(4)
nS
nZ
IH
(5)
nY0
nY1
1
2
V
IL
or V
IH
(6)
switch
V
I
SW
I
GND
0
1
2
3
4
5
V (V)
I
012aaa002
RON = VSW / ISW
.
(1) VCC = 1.5 V.
(2) CC = 1.8 V.
V
(3) VCC = 2.5 V.
(4) VCC = 2.7 V.
(5)
(6) VCC = 4.3 V.
Measured at Tamb = 25 C.
VCC = 3.3 V.
Fig 8. Test circuit for measuring ON resistance
Fig 9. Typical ON resistance as a function of input
voltage
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
9 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
001aag565
001aag566
1.6
1.0
R
(Ω)
ON
R
(Ω)
ON
0.8
1.2
(1)
(2)
(3)
(4)
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
0.8
0.4
0
0
1
2
3
0
1
2
3
V (V)
I
V (V)
I
(1) Tamb = 125 C.
(2) amb = 85 C.
(1) Tamb = 125 C.
(2) amb = 85 C.
T
T
(3) Tamb = 25 C.
(4) Tamb = 40 C.
(3) Tamb = 25 C.
(4) Tamb = 40 C.
Fig 10. ON resistance as a function of input voltage;
VCC = 1.5 V
Fig 11. ON resistance as a function of input voltage;
VCC = 1.8 V
001aag567
001aag568
1.0
1.0
R
ON
R
ON
(Ω)
(Ω)
0.8
0.8
0.6
0.4
0.2
0
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
0
1
2
3
0
1
2
3
V (V)
V (V)
I
I
(1) Tamb = 125 C.
(2) amb = 85 C.
(1) Tamb = 125 C.
(2) amb = 85 C.
T
T
(3) Tamb = 25 C.
(4) Tamb = 40 C.
(3) Tamb = 25 C.
(4) Tamb = 40 C.
Fig 12. ON resistance as a function of input voltage;
VCC = 2.5 V
Fig 13. ON resistance as a function of input voltage;
VCC = 2.7 V
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
10 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
001aag569
001aaj896
1.0
1.0
R
ON
R
ON
(Ω)
(Ω)
0.8
0.8
(1)
(2)
(3)
(4)
0.6
0.4
0.2
0
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
0
1
2
3
4
0
1
2
3
4
5
V (V)
I
V (V)
I
(1) Tamb = 125 C.
(2) amb = 85 C.
(1) Tamb = 125 C.
(2) amb = 85 C.
T
T
(3) Tamb = 25 C.
(4) Tamb = 40 C.
(3) Tamb = 25 C.
(4) Tamb = 40 C.
Fig 14. ON resistance as a function of input voltage;
VCC = 3.3 V
Fig 15. ON resistance as a function of input voltage;
VCC = 4.3 V
12. Dynamic characteristics
Table 9.
Dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit see Figure 18.
Symbol Parameter
Conditions
Tamb = 25 C
Tamb = 40 C to +125 C Unit
Min Typ[1] Max
Min
Max
Max
(85 C) (125 C)
ten
enable time
nS to nZ or nYn;
see Figure 16
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
-
41
30
20
19
19
90
70
45
40
40
-
-
-
-
-
120
80
120
90
ns
ns
ns
ns
ns
50
55
45
45
50
50
tdis
disable time
nS to nZ or nYn;
see Figure 16
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
-
24
15
9
70
55
25
20
20
-
-
-
-
-
80
60
30
25
25
90
65
35
30
30
ns
ns
ns
ns
ns
8
8
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
11 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
Table 9.
Dynamic characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit see Figure 18.
Symbol Parameter
Conditions
Tamb = 25 C
Tamb = 40 C to +125 C Unit
Min Typ[1] Max
Min
Max
Max
(85 C) (125 C)
[2]
tb-m
break-before-make see Figure 17
time
VCC = 1.4 V to 1.6 V
-
-
-
-
-
20
17
13
11
11
-
-
-
-
-
9
7
4
3
2
-
-
-
-
-
-
-
-
-
-
ns
ns
ns
ns
ns
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
[1] Typical values are measured at Tamb = 25 C and VCC = 1.5 V, 1.8 V, 2.5 V, 3.3 V and 4.3 V respectively.
[2] Break-before-make guaranteed by design.
12.1 Waveform and test circuits
V
I
V
nS input
M
t
GND
t
en
dis
V
OH
V
X
V
X
nZ output
OFF to HIGH
HIGH to OFF
nY1 connected to V
EXT
GND
t
t
en
dis
V
OH
V
X
V
X
nZ output
nY0 connected to V
EXT
HIGH to OFF
OFF to HIGH
012aaa003
GND
Measurement points are given in Table 10.
Logic level: VOH is typical output voltage level that occurs with the output load.
Fig 16. Enable and disable times
Table 10. Measurement points
Supply voltage
VCC
Input
VM
Output
VX
1.4 V to 4.3 V
0.5VCC
0.9VOH
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
12 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
V
CC
nS
nZ
nY0
nY1
G
V
EXT
= 1.5 V
V
V
R
L
C
L
V
I
O
GND
012aaa004
a. Test circuit
V
I
0.5V
I
0.9V
O
0.9V
O
V
O
t
b-m
001aag572
b. Input and output measurement points
Fig 17. Test circuit for measuring break-before-make timing
V
CC
nS
nZ
nY0
nY1
1
2
switch
G
V
V
V
R
L
C
L
V
EXT
= 1.5 V
I
O
GND
012aaa005
Test data is given in Table 11.
Definitions test circuit:
RL = Load resistance.
CL = Load capacitance including jig and probe capacitance.
VEXT = External voltage for measuring switching times.
Fig 18. Test circuit for measuring switching times
Table 11. Test data
Supply voltage
VCC
Input
VI
Load
CL
tr, tf
2.5 ns
RL
1.4 V to 4.3 V
VCC
35 pF
50
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
13 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
12.2 Additional dynamic characteristics
Table 12. Additional dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise
specified); tr = tf 2.5 ns; Tamb = 25 C.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
[1]
THD
total harmonic
distortion
fi = 20 Hz to 20 kHz; RL = 32 ; see Figure 19
VCC = 1.4 V; VI = 1 V (p-p)
VCC = 1.65 V; VI = 1.2 V (p-p)
VCC = 2.3 V; VI = 1.5 V (p-p)
VCC = 2.7 V; VI = 2 V (p-p)
VCC = 4.3 V; VI = 2 V (p-p)
RL = 50 ; see Figure 20
VCC = 1.4 V to 4.3 V
-
-
-
-
-
0.15
-
-
-
-
-
%
%
%
%
%
0.10
0.02
0.02
0.02
[1]
[1]
f(3dB)
3 dB frequency
response
-
-
60
-
-
MHz
dB
iso
isolation (OFF-state)
crosstalk voltage
fi = 100 kHz; RL = 50 ; see Figure 21
VCC = 1.4 V to 4.3 V
90
Vct
between digital inputs and switch;
fi = 1 MHz; CL = 50 pF; RL = 50 ; see Figure 22
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
0.2
0.3
-
-
V
V
[1]
Xtalk
Qinj
crosstalk
between switches;
fi = 100 kHz; RL = 50 ; see Figure 23
VCC = 1.4 V to 4.3 V
-
90
-
dB
charge injection
fi = 1 MHz; CL = 0.1 nF; RL = 1 M; Vgen = 0 V;
Rgen = 0 ; see Figure 24
VCC = 1.5 V
VCC = 1.8 V
VCC = 2.5 V
VCC = 3.3 V
VCC = 4.3 V
-
-
-
-
-
3
4
-
-
-
-
-
pC
pC
pC
pC
pC
6
9
15
[1] fi is biased at 0.5VCC
.
12.3 Test circuits
V
CC
0.5V
CC
switch nS
R
L
1
2
V
IL
nS
nZ
nY0
nY1
1
2
V
IL
or V
IH
switch
V
IH
f
D
i
GND
012aaa006
Fig 19. Test circuit for measuring total harmonic distortion
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
14 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
V
CC
0.5V
CC
switch nS
R
L
1
2
V
IL
nS
nZ
nY0 1
nY1 2
V
IL
or V
IH
switch
V
IH
f
dB
i
GND
012aaa007
Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads 3 dB.
Fig 20. Test circuit for measuring the frequency response when channel is in ON-state
0.5V
V
CC
0.5V
CC
CC
switch nS
R
L
R
L
1
2
V
IH
nS
nZ
nY0
nY1
1
2
V
IL
or V
IH
switch
V
IL
f
dB
i
GND
012aaa008
Adjust fi voltage to obtain 0 dBm level at input.
Fig 21. Test circuit for measuring isolation (OFF-state)
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
15 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
switch nS
V
CC
1
2
V
IL
V
IH
nS
nZ
nY0
nY1
1
2
switch
0.5V
logic
input
G
V
I
R
L
R
L
C
L
V
O
V
0.5V
CC
CC
012aaa009
a. Test circuit
logic
input (nS)
off
on
off
V
ct
V
O
012aaa010
b. Input and output pulse definitions
Fig 22. Test circuit for measuring crosstalk voltage between digital inputs and switch
0.5V
CC
CHANNEL
ON
R
L
nY0 or nZ
nZ or nY0
f
50 Ω
V
V
i
O1
0.5V
CC
nS
V
IL
R
L
nY0 or nZ
nZ or nY0
R
50 Ω
i
CHANNEL
OFF
V
V
O2
001aak178
20 log10 (VO2 / VO1) or 20 log10 (VO1 / VO2).
Fig 23. Test circuit for measuring crosstalk between switches
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
16 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
V
CC
nS
nZ
nY0
nY1
1
2
switch
R
gen
G
V
V
O
R
L
C
L
I
V
gen
GND
012aaa011
a. Test circuit
logic
input
(nS) off
on
off
V
O
ΔV
O
012aaa012
b. Input and output pulse definitions
Definition: Qinj = VO CL.
VO = output voltage variation.
Rgen = generator resistance.
Vgen = generator voltage.
Fig 24. Test circuit for measuring charge injection
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
17 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
13. Package outline
HXQFN16U: plastic thermal enhanced extremely thin quad flat package; no leads;
16 terminals; UTLP based; body 3 x 3 x 0.5 mm
SOT1039-1
D
B
A
terminal 1
index area
E
A
A
1
detail X
e
1
e
1/2 e
C
M
v
C A
C
B
b
L
1
y
1
y
M
w
C
5
8
L
9
4
1
e
E
h
e
2
1/2 e
12
terminal 1
index area
16
13
X
D
h
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
A
b
D
D
h
E
E
h
e
e
1
e
2
L
L
v
w
y
y
1
1
1
max
0.05 0.35
0.00 0.25
3.1
2.9
1.95
1.75
3.1
2.9
1.95
1.75
0.35
0.25
0.1
0.0
mm
0.5
0.5
1.5
1.5
0.1
0.05 0.05
0.1
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
- - -
JEDEC
JEITA
07-11-14
07-12-01
SOT1039-1
- - -
Fig 25. Package outline SOT1039-1 (HXQFN16U)
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
18 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1
D
E
A
X
c
y
H
v
M
A
E
Z
9
16
Q
(A )
3
A
2
A
A
1
pin 1 index
θ
L
p
L
1
8
detail X
w
M
b
p
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(2)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
Z
θ
1
2
3
p
E
p
max.
8o
0o
0.15
0.05
0.95
0.80
0.30
0.19
0.2
0.1
5.1
4.9
4.5
4.3
6.6
6.2
0.75
0.50
0.4
0.3
0.40
0.06
mm
1.1
0.65
0.25
1
0.2
0.13
0.1
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-18
SOT403-1
MO-153
Fig 26. Package outline SOT403-1 (TSSOP16)
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
19 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
XQFN16: plastic, extremely thin quad flat package; no leads;
16 terminals; body 1.80 x 2.60 x 0.50 mm
SOT1161-1
X
D
B
A
E
terminal 1
index area
A
A
1
A
3
detail X
e
1
C
v
C A
C
B
e
b
y
1
y
w
C
5
8
L
4
1
9
e
e
2
12
terminal 1
index area
16
13
L
1
0
1
2 mm
scale
Dimensions
(1)
Unit
A
A
1
A
3
b
D
E
e
e
e
2
L
L
1
v
w
y
y
1
1
max 0.5 0.05
mm nom
min
0.25 1.9 2.7
0.127 0.20 1.8 2.6 0.4 1.2 1.2 0.40 0.50 0.1 0.05 0.05 0.05
0.15 1.7 2.5 0.35 0.45
0.45 0.55
0.00
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
sot1161-1_po
References
Outline
version
European
projection
Issue date
IEC
- - -
JEDEC
- - -
JEITA
- - -
09-12-28
09-12-29
SOT1161-1
Fig 27. Package outline SOT1161-1 (XQFN16)
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
20 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
14. Abbreviations
Table 13. Abbreviations
Acronym
CDM
Description
Charged Device Model
CMOS
ESD
Complementary Metal-Oxide Semiconductor
ElectroStatic Discharge
HBM
Human Body Model
MM
Machine Model
PDA
Personal Digital Assistant
15. Revision history
Table 14. Revision history
Document ID
NX3L2467 v.3
Modifications:
NX3L2467 v.2
Modifications:
Release date
20101229
Data sheet status
Change notice
Supersedes
Product data sheet
-
NX3L2467 v.2
• Section 2: IEC61000-4-2 added.
20100519 Product data sheet
-
NX3L2467 v.1
• Added type number NX3L2467GU (XQFN16 / SOT1161 package).
• Figure 1 changed: pin numbers removed from logic symbol.
NX3L2467 v.1
20090623
Product data sheet
-
-
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
21 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
suitable for use in medical, military, aircraft, space or life support equipment,
16.2 Definitions
nor in applications where failure or malfunction of an NXP Semiconductors
product can reasonably be expected to result in personal injury, death or
severe property or environmental damage. NXP Semiconductors accepts no
liability for inclusion and/or use of NXP Semiconductors products in such
equipment or applications and therefore such inclusion and/or use is at the
customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use in automotive applications — This NXP
Semiconductors product has been qualified for use in automotive
applications. The product is not designed, authorized or warranted to be
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
22 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
NX3L2467
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 3 — 29 December 2010
23 of 24
NX3L2467
NXP Semiconductors
Dual low-ohmic double-pole double-throw analog switch
18. Contents
1
2
3
4
5
6
General description. . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3
7
7.1
7.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
8
Functional description . . . . . . . . . . . . . . . . . . . 4
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recommended operating conditions. . . . . . . . 5
9
10
11
Static characteristics. . . . . . . . . . . . . . . . . . . . . 6
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ON resistance. . . . . . . . . . . . . . . . . . . . . . . . . . 7
ON resistance test circuit and graphs. . . . . . . . 9
11.1
11.2
11.3
12
Dynamic characteristics . . . . . . . . . . . . . . . . . 11
Waveform and test circuits . . . . . . . . . . . . . . . 12
Additional dynamic characteristics . . . . . . . . . 14
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
12.1
12.2
12.3
13
14
15
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 21
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 21
16
Legal information. . . . . . . . . . . . . . . . . . . . . . . 22
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 22
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
16.1
16.2
16.3
16.4
17
18
Contact information. . . . . . . . . . . . . . . . . . . . . 23
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2010.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 29 December 2010
Document identifier: NX3L2467
相关型号:
©2020 ICPDF网 联系我们和版权申明