P89C51RB2 [NXP]
80C51 8-bit Flash microcontroller family; 80C51的8位闪存微控制器系列型号: | P89C51RB2 |
厂家: | NXP |
描述: | 80C51 8-bit Flash microcontroller family |
文件: | 总56页 (文件大小:312K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
P89C51RB2Hxx
P89C51RC2Hxx
P89C51RD2Hxx
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
Product data
Supersedes data of 2001 Jun 27
2002 May 24
Philips
Semiconductors
Philips Semiconductors
Preliminary data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOGIC SYMBOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PINNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plastic Dual In-Line Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plastic Leaded Chip Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plastic Quad Flat Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL FUNCTION REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL FUNCTION REGISTERS (CONTINUED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OSCILLATOR CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOW POWER MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stop Clock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER-ON FLAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Design Consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ONCEE Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmable Clock-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIMER 2 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-Reload Mode (Up or Down Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Baud Rate Generator Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of Baud Rate Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer/Counter 2 Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enhanced UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Address Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Priority Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reduced EMI Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reduced EMI Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUXR (8EH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dual DPTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUXR1 (A2H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DPTR Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmable Counter Array (PCA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCA Capture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16-bit Software Timer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Speed Output Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pulse Width Modulator Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCA Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Expanded Data RAM Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HARDWARE WATCHDOG TIMER (ONE-TIME ENABLED WITH RESET-OUT FOR P89C51RB2/RC2/RD2HXX) . . . .
Using the WDT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
3
4
4
4
4
4
5
7
8
8
8
9
9
9
9
9
9
9
9
10
10
10
10
13
14
14
15
15
18
20
20
20
20
20
20
21
24
24
24
24
27
29
30
30
i
2002 May 24
Philips Semiconductors
Preliminary data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC ELECTRICAL CHARACTERISTICS (6 CLOCK MODE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC ELECTRICAL CHARACTERISTICS (12 CLOCK MODE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXPLANATION OF THE AC SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FLASH EPROM MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATURES – IN-SYSTEM PROGRAMMING (ISP) AND IN-APPLICATION PROGRAMMING (IAP) . . . . . . . . . . . . . . . .
CAPABILITIES OF THE PHILIPS 89C51RX2HXX FLASH-BASED MICROCONTROLLERS . . . . . . . . . . . . . . . . . . . . . . .
Flash organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flash Programming and Erasure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-On Reset Code Execution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Activation of the Boot Loader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In-System Programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the In-System Programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In Application Programming Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Watchdog Timer (WDT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REVISION HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
32
33
34
35
40
40
40
40
40
40
40
41
41
42
42
46
46
48
52
ii
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
DESCRIPTION
FEATURES
The P89C51RB2/RC2/RD2Hxx device contains a non-volatile
16KB/32KB/64KB Flash program memory that is both parallel
programmable and serial In-System and In-Application
Programmable. In-System Programming (ISP) allows the user to
download new code while the microcontroller sits in the application.
In-Application Programming (IAP) means that the microcontroller
fetches new program code and reprograms itself while in the
system. This allows for remote programming over a modem link.
A default serial loader (boot loader) program in ROM allows serial
In-System programming of the Flash memory via the UART without
the need for a loader in the Flash code. For In-Application
Programming, the user program erases and reprograms the Flash
memory by use of standard routines contained in ROM.
• 80C51 Central Processing Unit
• On-chip Flash Program Memory with In-System Programming
(ISP) and In-Application Programming (IAP) capability
• Boot ROM contains low level Flash programming routines for
downloading via the UART
• Can be programmed by the end-user application (IAP)
• Parallel programming with 87C51 compatible hardware interface
to programmer
• Six clocks per machine cycle operation (standard)
• 12 clocks per machine cycle operation (optional)
• Speed up to 20 MHz with 6 clock cycles per machine cycle
(40 MHz equivalent performance); up to 33 MHz with 12 clocks
per machine cycle
This device executes one machine cycle in 6 clock cycles, hence
providing twice the speed of a conventional 80C51. An OTP
configuration bit lets the user select conventional 12 clock timing
if desired.
• Fully static operation
This device is a Single-Chip 8-Bit Microcontroller manufactured in
advanced CMOS process and is a derivative of the 80C51
microcontroller family. The instruction set is 100% compatible with
the 80C51 instruction set.
• RAM expandable externally to 64 kbytes
• Four interrupt priority levels
• Seven interrupt sources
• Four 8-bit I/O ports
The device also has four 8-bit I/O ports, three 16-bit timer/event
counters, a multi-source, four-priority-level, nested interrupt structure,
an enhanced UART and on-chip oscillator and timing circuits.
• Full-duplex enhanced UART
– Framing error detection
The added features of the P89C51RB2/RC2/RD2Hxx makes it a
powerful microcontroller for applications that require pulse width
modulation, high-speed I/O and up/down counting capabilities such
as motor control.
– Automatic address recognition
• Power control modes
– Clock can be stopped and resumed
– Idle mode
– Power down mode
• Programmable clock out
• Second DPTR register
• Asynchronous port reset
• Low EMI (inhibit ALE)
• Programmable Counter Array (PCA)
– PWM
– Capture/compare
1
2002 May 24
853-2349 28312
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
ORDERING INFORMATION
MEMORY
FREQUENCY (MHz)
DWG #
TEMPERATURE
RANGE (°C)
AND PACKAGE
PART ORDER
NUMBER
VOLTAGE
RANGE
FLASH
RAM
6 CLOCK
MODE
12 CLOCK
MODE
1
2
P89C51RB2HBA
P89C51RB2HBBD
P89C51RC2HBP
P89C51RC2HBA
P89C51RC2HFA
P89C51RC2HBBD
P89C51RC2HFBD
P89C51RD2HBP
P89C51RD2HBA
P89C51RD2HBBD
16 kB
16 kB
32 kB
32 kB
32 kB
32 kB
32 kB
64 kB
64 kB
64 kB
512 B
512 B
512 B
512 B
512 B
512 B
512 B
1 kB
0 to +70, PLCC
0 to +70, LQFP
0 to +70, PDIP
0 to +70, PLCC
–40 to +85, PLCC
0 to +70, LQFP
–40 to +85, LQFP
0 to +70, PDIP
0 to +70, PLCC
0 to +70, LQFP
4.5–5.5 V
4.5–5.5 V
4.5–5.5 V
4.5–5.5 V
4.75–5.25 V
4.5–5.5 V
4.75–5.25 V
4.5–5.5 V
4.5–5.5 V
4.5–5.5 V
0 to 20 MHz
0 to 20 MHz
0 to 20 MHz
0 to 20 MHz
0 to 20 MHz
0 to 20 MHz
0 to 20 MHz
0 to 20 MHz
0 to 20 MHz
0 to 20 MHz
0 to 33 MHz
0 to 33 MHz
0 to 33 MHz
0 to 33 MHz
0 to 33 MHz
0 to 33 MHz
0 to 33 MHz
0 to 33 MHz
0 to 33 MHz
0 to 33 MHz
SOT187-2
SOT389-1
SOT129-1
SOT187-2
SOT187-2
SOT389-1
SOT389-1
SOT129-1
SOT187-2
SOT389-1
3
4
5
6
7
8
9
1 kB
10
1 kB
2
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
BLOCK DIAGRAM
P0.0–P0.7
P2.0–P2.7
PORT 0
DRIVERS
PORT 2
DRIVERS
V
V
CC
SS
RAM ADDR
REGISTER
PORT 0
LATCH
PORT 2
LATCH
FLASH
RAM
8
B
STACK
POINTER
ACC
REGISTER
PROGRAM
ADDRESS
REGISTER
TMP1
TMP2
BUFFER
ALU
SFRs
TIMERS
P.C.A.
PC
INCRE-
MENTER
PSW
8
16
PROGRAM
COUNTER
PSEN
ALE
DPTR’S
MULTIPLE
TIMING
AND
CONTROL
EAV
PP
RST
PORT 1
LATCH
PORT 3
LATCH
PD
OSCILLATOR
PORT 1
DRIVERS
PORT 3
DRIVERS
XTAL1
XTAL2
P1.0–P1.7
P3.0–P3.7
SU01065
3
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
LOGIC SYMBOL
Plastic Leaded Chip Carrier
6
1
40
V
V
SS
CC
XTAL1
7
39
ADDRESS AND
DATA BUS
LCC
XTAL2
RST
17
29
T2
T2EX
18
28
EA/V
PP
Pin Function
Pin Function
Pin Function
PSEN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
NIC*
P1.0/T2
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
P3.4/T0
P3.5/T1
P3.6/WR
P3.7/RD
XTAL2
XTAL1
V
SS
NIC*
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
P2.5/A13
P2.6/A14
31
32
33
34
35
36
37
38
39
40
41
42
43
44
P2.7/A15
PSEN
ALE/PROG
NIC*
ALE/PROG
RxD
P1.1/T2EX
P1.2/ECI
P1.3/CEX0
P1.4/CEX1
P1.5/CEX2
P1.6/CEX3
P1.7/CEX4
RST
P3.0/RxD
NIC*
P3.1/TxD
P3.2/INT0
P3.3/INT1
TxD
INT0
EA/V
PP
INT1
T0
T1
WR
RD
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
ADDRESS BUS
SU01302
V
CC
* NO INTERNAL CONNECTION
PINNING
Plastic Dual In-Line Package
SU00023
Plastic Quad Flat Pack
T2/P1.0
40
39
V
CC
1
2
3
44
34
T2EX/P1.1
P0.0/AD0
ECI/P1.2
38 P0.1/AD1
37 P0.2/AD2
1
33
23
CEX0/P1.3
CEX1/P1.4
4
5
36
P0.3/AD3
35 P0.4/AD4
34
LQFP
CEX2/P1.5
CEX3/P1.6
CEX4/P1.7
RST
6
7
8
9
11
P0.5/AD5
33 P0.6/AD6
32
12
Pin Function
22
P0.7/AD7
Pin Function
Pin Function
DUAL
IN-LINE
PACKAGE
31 EA/V
RxD/P3.0 10
TxD/P3.1 11
INT0/P3.2 12
PP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
P1.5/CEX2
P1.6/CEX3
P1.7/CEX4
RST
P3.0/RxD
NIC*
P3.1/TxD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
P3.6/WR
P3.7/RD
XTAL2
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V
31
32
33
34
35
36
37
38
39
40
41
42
43
44
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
SS
30
NIC*
ALE/PROG
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
P2.5/A13
P2.6/A14
P2.7/A15
PSEN
29 PSEN
28
13
INT1/P3.3
P2.7/A15
27 P2.6/A14
26
T0/P3.4 14
T1/P3.5 15
WR/P3.6 16
RD/P3.7 17
XTAL2 18
XTAL1 19
V
CC
P2.5/A13
NIC*
P1.0/T2
P1.1/T2EX
P1.2/ECI
P1.3/CEX0
P1.4/CEX1
25 P2.4/A12
24 P2.3/A11
ALE/PROG
NIC*
EA/V
PP
23
22
P2.2/A10
P2.1/A9
P2.0/A8
XTAL1
P0.7/AD7
SU01400
* NO INTERNAL CONNECTION
21
V
20
SS
SU00021
4
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
PIN DESCRIPTIONS
PIN NUMBER
MNEMONIC
TYPE
NAME AND FUNCTION
PDIP
20
PLCC
22
LQFP
16
V
SS
I
I
Ground: 0 V reference.
V
CC
40
44
38
Power Supply: This is the power supply voltage for normal, idle, and power-down
operation.
P0.0–0.7
39–32
1–8
43–36
2–9
37–30
I/O
Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s
written to them float and can be used as high-impedance inputs. Port 0 is also the
multiplexed low-order address and data bus during accesses to external program
and data memory. In this application, it uses strong internal pull-ups when emitting 1s.
P1.0–P1.7
40–44,
1–3
I/O
Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups on all pins.
Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, port 1 pins that are externally pulled low will
source current because of the internal pull-ups. (See DC Electrical Characteristics:
I ).
IL
Alternate functions for P89C51RB2/RC2/RD2Hxx Port 1 include:
1
2
40
I/O
T2 (P1.0): Timer/Counter 2 external count input/Clockout (see Programmable
Clock-Out)
2
3
4
5
6
7
8
3
4
5
6
7
8
9
41
42
43
44
1
I
T2EX (P1.1): Timer/Counter 2 Reload/Capture/Direction Control
ECI (P1.2): External Clock Input to the PCA
I
I/O
I/O
I/O
I/O
I/O
CEX0 (P1.3): Capture/Compare External I/O for PCA module 0
CEX1 (P1.4): Capture/Compare External I/O for PCA module 1
CEX2 (P1.5): Capture/Compare External I/O for PCA module 2
CEX3 (P1.6): Capture/Compare External I/O for PCA module 3
CEX4 (P1.7): Capture/Compare External I/O for PCA module 4
2
3
P2.0–P2.7
21–28
24–31
18–25
I/O
Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that
have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, port 2 pins that are externally being pulled low will source current
because of the internal pull-ups. (See DC Electrical Characteristics: I ). Port 2
IL
emits the high-order address byte during fetches from external program memory
and during accesses to external data memory that use 16-bit addresses (MOVX
@DPTR). In this application, it uses strong internal pull-ups when emitting 1s.
During accesses to external data memory that use 8-bit addresses (MOV @Ri),
port 2 emits the contents of the P2 special function register.
P2.7 must be a “I” to program and erase the device.
P3.0–P3.7
10–17
11,
13–19
5, 7–13
I/O
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that
have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, port 3 pins that are externally being pulled low will source current
because of the pull-ups. (See DC Electrical Characteristics: I ). Port 3 also serves
IL
the special features of the P89C51RB2/RC2/RD2Hxx, as listed below:
10
11
12
13
14
15
16
17
11
13
14
15
16
17
18
19
5
7
I
O
I
RxD (P3.0): Serial input port
TxD (P3.1): Serial output port
8
INT0 (P3.2): External interrupt
9
I
INT1 (P3.3): External interrupt
10
11
12
13
I
T0 (P3.4): Timer 0 external input
I
T1 (P3.5): Timer 1 external input
O
O
WR (P3.6): External data memory write strobe
RD (P3.7): External data memory read strobe
RST
ALE
9
10
4
I
Reset: A high on this pin for two machine cycles while the oscillator is running,
resets the device. An internal resistor to V permits a power-on reset using only
SS
an external capacitor to V
.
CC
30
33
27
O
Address Latch Enable: Output pulse for latching the low byte of the address
during an access to external memory. In normal operation, ALE is emitted twice
every machine cycle, and can be used for external timing or clocking. Note that one
ALE pulse is skipped during each access to external data memory. ALE can be
disabled by setting SFR auxiliary.0. With this bit set, ALE will be active only during a
MOVX instruction.
5
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
PIN NUMBER
MNEMONIC
TYPE
NAME AND FUNCTION
PDIP
PLCC
LQFP
PSEN
29
32
26
O
Program Store Enable: The read strobe to external program memory. When
executing code from the external program memory, PSEN is activated twice each
machine cycle, except that two PSEN activations are skipped during each access
to external data memory. PSEN is not activated during fetches from internal
program memory.
EA/V
31
35
29
I
External Access Enable/Programming Supply Voltage: EA must be externally
held low to enable the device to fetch code from external program memory
locations. If EA is held high, the device executes from internal program memory.
The value on the EA pin is latched when RST is released and any subsequent
changes have no effect. This pin also receives the programming supply voltage
PP
(V ) during Flash programming.
PP
XTAL1
19
18
21
20
15
14
I
Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock
generator circuits.
XTAL2
O
Crystal 2: Output from the inverting oscillator amplifier.
NOTE:
To avoid “latch-up” effect at power-on, the voltage on any pin (other than V ) must not be higher than V + 0.5 V or less than V – 0.5 V.
PP
CC
SS
6
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
SPECIAL FUNCTION REGISTERS
DIRECT
ADDRESS
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
RESET
VALUE
SYMBOL
DESCRIPTION
MSB
E7
–
LSB
E0
ACC*
AUXR#
AUXR1#
B*
Accumulator
E0H
8EH
A2H
F0H
E6
–
E5
E4
–
E3
–
E2
–
E1
00H
EXTRAM
Auxiliary
–
AO
xxxxxx00B
xxxxxxx0B
00H
ENBOOT
Auxiliary 1
B register
–
–
–
GF2
F3
0
–
DPS
F0
F7
F6
F5
F4
F2
F1
CCAP0H# Module 0 Capture High
CCAP1H# Module 1 Capture High
CCAP2H# Module 2 Capture High
CCAP3H# Module 3 Capture High
CCAP4H# Module 4 Capture High
CCAP0L# Module 0 Capture Low
CCAP1L# Module 1 Capture Low
CCAP2L# Module 2 Capture Low
CCAP3L# Module 3 Capture Low
CCAP4L# Module 4 Capture Low
FAH
FBH
FCH
FDH
FEH
EAH
EBH
ECH
EDH
EEH
xxxxxxxxB
xxxxxxxxB
xxxxxxxxB
xxxxxxxxB
xxxxxxxxB
xxxxxxxxB
xxxxxxxxB
xxxxxxxxB
xxxxxxxxB
xxxxxxxxB
CCAPM0# Module 0 Mode
CCAPM1# Module 1 Mode
CCAPM2# Module 2 Mode
CCAPM3# Module 3 Mode
CCAPM4# Module 4 Mode
DAH
DBH
DCH
DDH
DEH
–
–
–
–
–
ECOM CAPP
ECOM CAPP
ECOM CAPP
ECOM CAPP
ECOM CAPP
CAPN
CAPN
CAPN
CAPN
CAPN
MAT
MAT
MAT
MAT
MAT
TOG
TOG
TOG
TOG
TOG
PWM
PWM
PWM
PWM
PWM
ECCF
ECCF
ECCF
ECCF
ECCF
x0000000B
x0000000B
x0000000B
x0000000B
x0000000B
DF
CF
DE
CR
DD
–
DC
DB
DA
D9
D8
CCON*#
CH#
CL#
PCA Counter Control
PCA Counter High
PCA Counter Low
D8H
F9H
E9H
CCF4
CCF3
CCF2
CCF1
CCF0
00x00000B
00H
00H
CMOD#
PCA Counter Mode
D9H
CIDL
WDTE
–
–
–
CPS1
CPS0
ECF
00xxx000B
DPTR:
DPH
DPL
Data Pointer (2 bytes)
Data Pointer High
Data Pointer Low
83H
82H
00H
00H
AF
EA
BF
–
AE
EC
AD
ET2
BD
AC
ES
AB
ET1
BB
AA
EX1
BA
A9
ET0
B9
A8
EX0
B8
IE*
Interrupt Enable 0
Interrupt Priority
A8H
B8H
B7H
00H
BE
BC
PS
IP*
PPC
B6
PT2
B5
PT1
B3
PX1
B2
PT0
B1
PX0
B0
x0000000B
x0000000B
B7
–
B4
IPH#
Interrupt Priority High
PPCH
PT2H
PSH
PT1H
PX1H
PT0H
PX0H
87
AD7
97
86
AD6
96
85
AD5
95
84
AD4
94
83
AD3
93
82
AD2
92
81
AD1
91
80
AD0
90
P0*
P1*
P2*
P3*
Port 0
Port 1
Port 2
80H
90H
A0H
FFH
FFH
FFH
CEX4
A7
CEX3
A6
CEX2
A5
CEX1
A4
CEX0
A3
ECI
A2
T2EX
A1
T2
A0
AD15
B7
AD14
B6
AD13
B5
AD12
B4
AD11
B3
AD10
B2
AD9
B1
AD8
B0
Port 3
B0H
87H
RD
WR
T1
T0
INT1
INT0
TxD
RxD
FFH
1
PCON#
Power Control
SMOD1 SMOD0
–
POF
GF1
GF0
PD
IDL
00xxx000B
*
SFRs are bit addressable.
#
–
SFRs are modified from or added to the 80C51 SFRs.
Reserved bits.
1. Reset value depends on reset source.
7
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
SPECIAL FUNCTION REGISTERS (CONTINUED)
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
DIRECT
ADDRESS
RESET
VALUE
SYMBOL
DESCRIPTION
MSB
LSB
D7
CY
D6
AC
D5
F0
D4
D3
D2
D1
F1
D0
P
PSW*
Program Status Word
D0H
RS1
RS0
OV
00000000B
RCAP2H#
RCAP2L#
Timer 2 Capture High
Timer 2 Capture Low
CBH
CAH
00H
00H
SADDR# Slave Address
SADEN# Slave Address Mask
A9H
B9H
00H
00H
SBUF
Serial Data Buffer
99H
xxxxxxxxB
9F
9E
9D
9C
9B
9A
99
TI
98
RI
SM0/FE
SCON*
SP
Serial Control
Stack Pointer
98H
81H
SM1
SM2
REN
TB8
RB8
00H
07H
8F
8E
8D
8C
8B
8A
89
88
TCON*
Timer Control
88H
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
00H
CF
TF2
–
CE
EXF2
–
CD
RCLK
–
CC
TCLK
–
CB
EXEN2
–
CA
TR2
–
C9
C8
T2CON*
Timer 2 Control
C8H
C9H
C/T2
T2OE
CP/RL2 00H
DCEN xxxxxx00B
T2MOD# Timer 2 Mode Control
TH0
TH1
TH2#
TL0
TL1
TL2#
Timer High 0
Timer High 1
Timer High 2
Timer Low 0
Timer Low 1
Timer Low 2
8CH
8DH
CDH
8AH
8BH
CCH
00H
00H
00H
00H
00H
00H
TMOD
Timer Mode
89H
A6H
GATE
C/T
M1
M0
GATE
C/T
M1
M0
00H
WDTRST Watchdog Timer Reset
*
SFRs are bit addressable.
#
–
SFRs are modified from or added to the 80C51 SFRs.
Reserved bits.
OSCILLATOR CHARACTERISTICS
RESET
XTAL1 and XTAL2 are the input and output, respectively, of an
inverting amplifier. The pins can be configured for use as an
on-chip oscillator.
A reset is accomplished by holding the RST pin high for at least two
machine cycles (12 oscillator periods in 6 clock mode, or 24 oscillator
periods in 12 clock mode), while the oscillator is running. To ensure a
good power-on reset, the RST pin must be high long enough to allow
the oscillator time to start up (normally a few milliseconds) plus two
To drive the device from an external clock source, XTAL1 should be
driven while XTAL2 is left unconnected. Minimum and maximum
high and low times specified in the data sheet must be observed.
machine cycles. At power-on, the voltage on V and RST must
CC
come up at the same time for a proper start-up. Ports 1, 2, and 3 will
asynchronously be driven to their reset condition when a voltage
This device is configured at the factory to operate using 6 clock
periods per machine cycle, referred to in this datasheet as “6 clock
mode”. (This yields performance equivalent to twice that of standard
80C51 family devices). It may be optionally configured on
commercially-available EPROM programming equipment to operate
at 12 clocks per machine cycle, referred to in this datasheet as
“12 clock mode”. Once 12 clock mode has been configured, it
cannot be changed back to 6 clock mode.
above V
(min.) is applied to RESET.
IH1
The value on the EA pin is latched when RST is deasserted and has
no further effect.
8
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
LOW POWER MODES
Stop Clock Mode
Design Consideration
The static design enables the clock speed to be reduced down to
0 MHz (stopped). When the oscillator is stopped, the RAM and
Special Function Registers retain their values. This mode allows
step-by-step utilization and permits reduced system power
consumption by lowering the clock frequency down to any value. For
lowest power consumption the Power Down mode is suggested.
• When the idle mode is terminated by a hardware reset, the device
normally resumes program execution, from where it left off, up to
two machine cycles before the internal reset algorithm takes
control. On-chip hardware inhibits access to internal RAM in this
event, but access to the port pins is not inhibited. To eliminate the
possibility of an unexpected write when Idle is terminated by reset,
the instruction following the one that invokes Idle should not be
one that writes to a port pin or to external memory.
Idle Mode
In the idle mode (see Table 1), the CPU puts itself to sleep while all
of the on-chip peripherals stay active. The instruction to invoke the
idle mode is the last instruction executed in the normal operating
mode before the idle mode is activated. The CPU contents, the
on-chip RAM, and all of the special function registers remain intact
during this mode. The idle mode can be terminated either by any
enabled interrupt (at which time the process is picked up at the
interrupt service routine and continued), or by a hardware reset
which starts the processor in the same manner as a power-on reset.
ONCE Mode
The ONCE (“On-Circuit Emulation”) Mode facilitates testing and
debugging of systems without the device having to be removed from
the circuit. The ONCE Mode is invoked by:
1. Pull ALE low while the device is in reset and PSEN is high;
2. Hold ALE low as RST is deactivated.
While the device is in ONCE Mode, the Port 0 pins go into a float
state, and the other port pins and ALE and PSEN are weakly pulled
high. The oscillator circuit remains active. While the device is in this
mode, an emulator or test CPU can be used to drive the circuit.
Normal operation is restored when a normal reset is applied.
Power-Down Mode
To save even more power, a Power Down mode (see Table 1) can
be invoked by software. In this mode, the oscillator is stopped and
the instruction that invoked Power Down is the last instruction
executed. The on-chip RAM and Special Function Registers retain
Programmable Clock-Out
A 50% duty cycle clock can be programmed to come out on P1.0.
This pin, besides being a regular I/O pin, has two alternate
functions. It can be programmed:
their values down to 2.0 V and care must be taken to return V to
CC
the minimum specified operating voltages before the Power Down
Mode is terminated.
1. to input the external clock for Timer/Counter 2, or
Either a hardware reset or external interrupt can be used to exit from
Power Down. Reset redefines all the SFRs but does not change the
on-chip RAM. An external interrupt allows both the SFRs and the
on-chip RAM to retain their values.
2. to output a 50% duty cycle clock ranging from 122 Hz to 8 MHz at
a 16 MHz operating frequency (61 Hz to 4 MHz in 12 clock mode).
To configure the Timer/Counter 2 as a clock generator, bit C/T2 (in
T2CON) must be cleared and bit T20E in T2MOD must be set. Bit
TR2 (T2CON.2) also must be set to start the timer.
To properly terminate Power Down, the reset or external interrupt
should not be executed before V is restored to its normal
CC
operating level and must be held active long enough for the
oscillator to restart and stabilize (normally less than 10 ms).
The Clock-Out frequency depends on the oscillator frequency and
the reload value of Timer 2 capture registers (RCAP2H, RCAP2L)
as shown in this equation:
With an external interrupt, INT0 and INT1 must be enabled and
configured as level-sensitive. Holding the pin low restarts the oscillator
but bringing the pin back high completes the exit. Once the interrupt
is serviced, the next instruction to be executed after RETI will be the
one following the instruction that put the device into Power Down.
Oscillator Frequency
n (65536 + RCAP2H, RCAP2L)
n =
2 in 6 clock mode
4 in 12 clock mode
POWER-ON FLAG
The Power-On Flag (POF) is set by on-chip circuitry when the V
Where (RCAP2H,RCAP2L) = the content of RCAP2H and RCAP2L
taken as a 16-bit unsigned integer.
CC
level on the P89C51RB2/RC2/RD2Hxx rises from 0 to 5 V. The POF
bit can be set or cleared by software allowing a user to determine if
the reset is the result of a power-on or a warm start after
In the Clock-Out mode Timer 2 roll-overs will not generate an
interrupt. This is similar to when it is used as a baud-rate generator.
It is possible to use Timer 2 as a baud-rate generator and a clock
generator simultaneously. Note, however, that the baud-rate and the
Clock-Out frequency will be the same.
powerdown. The V level must remain above 3 V for the POF to
CC
remain unaffected by the V level.
CC
Table 1. External Pin Status During Idle and Power-Down Mode
MODE
PROGRAM MEMORY
Internal
ALE
PSEN
PORT 0
Data
PORT 1
Data
PORT 2
Data
PORT 3
Data
Idle
Idle
1
1
0
0
1
1
0
0
External
Float
Data
Address
Data
Data
Power-down
Power-down
Internal
Data
Data
Data
External
Float
Data
Data
Data
9
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
Counter Enable) which is located in the T2MOD register (see
Figure 3). When reset is applied the DCEN=0 which means Timer 2
will default to counting up. If DCEN bit is set, Timer 2 can count up
or down depending on the value of the T2EX pin.
TIMER 2 OPERATION
Timer 2
Timer 2 is a 16-bit Timer/Counter which can operate as either an
event timer or an event counter, as selected by C/T2* in the special
function register T2CON (see Figure 1). Timer 2 has three operating
modes: Capture, Auto-reload (up or down counting), and Baud Rate
Generator, which are selected by bits in the T2CON as shown in
Table 2.
Figure 4 shows Timer 2 which will count up automatically since
DCEN=0. In this mode there are two options selected by bit EXEN2
in T2CON register. If EXEN2=0, then Timer 2 counts up to 0FFFFH
and sets the TF2 (Overflow Flag) bit upon overflow. This causes the
Timer 2 registers to be reloaded with the 16-bit value in RCAP2L
and RCAP2H. The values in RCAP2L and RCAP2H are preset by
software means.
Capture Mode
In the capture mode there are two options which are selected by bit
EXEN2 in T2CON. If EXEN2=0, then timer 2 is a 16-bit timer or
counter (as selected by C/T2* in T2CON) which, upon overflowing
sets bit TF2, the timer 2 overflow bit. This bit can be used to
generate an interrupt (by enabling the Timer 2 interrupt bit in the
IE register). If EXEN2= 1, Timer 2 operates as described above, but
with the added feature that a 1- to -0 transition at external input
T2EX causes the current value in the Timer 2 registers, TL2 and
TH2, to be captured into registers RCAP2L and RCAP2H,
respectively. In addition, the transition at T2EX causes bit EXF2 in
T2CON to be set, and EXF2 like TF2 can generate an interrupt
(which vectors to the same location as Timer 2 overflow interrupt.
The Timer 2 interrupt service routine can interrogate TF2 and EXF2
to determine which event caused the interrupt). The capture mode is
illustrated in Figure 2 (There is no reload value for TL2 and TH2 in
this mode. Even when a capture event occurs from T2EX, the
counter keeps on counting T2EX pin transitions or osc/6 pulses
(osc/12 in 12 clock mode).).
If EXEN2=1, then a 16-bit reload can be triggered either by an
overflow or by a 1-to-0 transition at input T2EX. This transition also
sets the EXF2 bit. The Timer 2 interrupt, if enabled, can be
generated when either TF2 or EXF2 are 1.
In Figure 5 DCEN=1 which enables Timer 2 to count up or down.
This mode allows pin T2EX to control the direction of count. When a
logic 1 is applied at pin T2EX Timer 2 will count up. Timer 2 will
overflow at 0FFFFH and set the TF2 flag, which can then generate
an interrupt, if the interrupt is enabled. This timer overflow also
causes the 16-bit value in RCAP2L and RCAP2H to be reloaded
into the timer registers TL2 and TH2.
When a logic 0 is applied at pin T2EX this causes Timer 2 to count
down. The timer will underflow when TL2 and TH2 become equal to
the value stored in RCAP2L and RCAP2H. Timer 2 underflow sets
the TF2 flag and causes 0FFFFH to be reloaded into the timer
registers TL2 and TH2.
Auto-Reload Mode (Up or Down Counter)
The external flag EXF2 toggles when Timer 2 underflows or overflows.
This EXF2 bit can be used as a 17th bit of resolution if needed. The
EXF2 flag does not generate an interrupt in this mode of operation.
In the 16-bit auto-reload mode, Timer 2 can be configured (as either
a timer or counter [C/T2* in T2CON]) then programmed to count up
or down. The counting direction is determined by bit DCEN (Down
(MSB)
(LSB)
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
C/T2
CP/RL2
Symbol
Position
Name and Significance
TF2
T2CON.7
T2CON.6
Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set
when either RCLK or TCLK = 1.
EXF2
Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and
EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2
interrupt routine. EXF2 must be cleared by software. EXF2 does not cause an interrupt in up/down
counter mode (DCEN = 1).
RCLK
TCLK
T2CON.5
T2CON.4
T2CON.3
Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock
in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.
Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock
in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.
EXEN2
Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative
transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to
ignore events at T2EX.
TR2
T2CON.2
T2CON.1
Start/stop control for Timer 2. A logic 1 starts the timer.
C/T2
Timer or counter select. (Timer 2)
0 = Internal timer (OSC/6 in 6-clock mode or OSC/12 in 12-clock mode)
1 = External event counter (falling edge triggered).
CP/RL2
T2CON.0
Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When
cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when
EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload
on Timer 2 overflow.
SU01251
Figure 1. Timer/Counter 2 (T2CON) Control Register
10
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
Table 2. Timer 2 Operating Modes
RCLK + TCLK
CP/RL2
TR2
1
MODE
0
0
1
X
0
1
16-bit Auto-reload
1
16-bit Capture
Baud rate generator
(off)
X
X
1
0
OSC
÷ n*
C/T2 = 0
TL2
(8 BITS)
TH2
(8 BITS)
TF2
C/T2 = 1
T2 Pin
Control
TR2
Capture
Transition
Detector
Timer 2
Interrupt
RCAP2L
RCAP2H
T2EX Pin
EXF2
Control
EXEN2
SU01252
* n = 6 in 6-clock mode, or 12 in 12-clock mode.
Figure 2. Timer 2 in Capture Mode
T2MOD
Address = 0C9H
Not Bit Addressable
—
Reset Value = XXXX XX00B
—
6
—
5
—
4
—
3
—
2
T2OE
1
DCEN
0
Bit
7
Symbol
Function
—
Not implemented, reserved for future use.*
Timer 2 Output Enable bit.
T2OE
DCEN
Down Count Enable bit. When set, this allows Timer 2 to be configured as an up/down counter.
*
User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features.
In that case, the reset or inactive value of the new bit will be 0, and its active value will be 1. The value read from a reserved bit is
indeterminate.
SU00729
Figure 3. Timer 2 Mode (T2MOD) Control Register
11
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
OSC
÷ n*
C/T2 = 0
TL2
(8 BITS)
TH2
(8 BITS)
C/T2 = 1
T2 PIN
CONTROL
TR2
RELOAD
TRANSITION
DETECTOR
RCAP2L
RCAP2H
TF2
TIMER 2
INTERRUPT
T2EX PIN
EXF2
CONTROL
EXEN2
SU01253
* n = 6 in 6-clock mode, or 12 in 12-clock mode.
Figure 4. Timer 2 in Auto-Reload Mode (DCEN = 0)
(DOWN COUNTING RELOAD VALUE)
FFH
FFH
TOGGLE
EXF2
÷ n*
OSC
C/T2 = 0
C/T2 = 1
OVERFLOW
TL2
TH2
TF2
INTERRUPT
T2 PIN
CONTROL
TR2
COUNT
DIRECTION
1 = UP
0 = DOWN
RCAP2L
RCAP2H
(UP COUNTING RELOAD VALUE)
T2EX PIN
* n = 6 in 6-clock mode, or 12 in 12-clock mode.
SU01254
Figure 5. Timer 2 Auto Reload Mode (DCEN = 1)
12
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
Timer 1
Overflow
÷ 2
“0”
“0”
“1”
OSC
C/T2 = 0
SMOD
RCLK
“1”
TL2
(8-bits)
TH2
(8-bits)
C/T2 = 1
T2 Pin
Control
RX Clock
÷ 16
÷ 16
“1”
“0”
TR2
Reload
TCLK
Transition
Detector
RCAP2L
RCAP2H
TX Clock
Timer 2
Interrupt
T2EX Pin
EXF2
Control
EXEN2
Note availability of additional external interrupt.
SU01213
Figure 6. Timer 2 in Baud Rate Generator Mode
The baud rates in modes 1 and 3 are determined by Timer 2’s
overflow rate given below:
Table 3. Timer 2 Generated Commonly Used
Baud Rates
Timer 2 Overflow Rate
Modes 1 and 3 Baud Rates +
Baud Rate
Timer 2
16
Osc Freq
12 clock
mode
6 clock
mode
The timer can be configured for either “timer” or “counter” operation.
In many applications, it is configured for “timer” operation (C/T2*=0).
Timer operation is different for Timer 2 when it is being used as a
baud rate generator.
RCAP2H
RCAP2L
375 k
9.6 k
2.8 k
2.4 k
1.2 k
300
110
300
110
750 k
19.2 k
5.6 k
4.8 k
2.4 k
600
220
600
220
12 MHz
12 MHz
12 MHz
12 MHz
12 MHz
12 MHz
12 MHz
6 MHz
FF
FF
FF
FF
FE
FB
F2
FD
F9
FF
D9
B2
64
C8
1E
AF
8F
57
Usually, as a timer it would increment every machine cycle (i.e.,
1
1
/ the oscillator frequency in 6 clock mode, / the oscillator
6
12
frequency in 12 clock mode). As a baud rate generator, it increments
OSC
at the oscillator frequency in 6 clock mode (
Thus the baud rate formula is as follows:
/ in 12 clock mode).
2
Modes 1 and 3 Baud Rates =
Oscillator Frequency
6 MHz
[ n * [65536 + (RCAP2H, RCAP2L)]]
* n =
16 in 6 clock mode
32 in 12 clock mode
Baud Rate Generator Mode
Bits TCLK and/or RCLK in T2CON (Table 3) allow the serial port
transmit and receive baud rates to be derived from either Timer 1 or
Timer 2. When TCLK= 0, Timer 1 is used as the serial port transmit
baud rate generator. When TCLK= 1, Timer 2 is used as the serial
port transmit baud rate generator. RCLK has the same effect for the
serial port receive baud rate. With these two bits, the serial port can
have different receive and transmit baud rates – one generated by
Timer 1, the other by Timer 2.
Where: (RCAP2H, RCAP2L)= The content of RCAP2H and
RCAP2L taken as a 16-bit unsigned integer.
The Timer 2 as a baud rate generator mode shown in Figure 6, is
valid only if RCLK and/or TCLK = 1 in T2CON register. Note that a
rollover in TH2 does not set TF2, and will not generate an interrupt.
Thus, the Timer 2 interrupt does not have to be disabled when
Timer 2 is in the baud rate generator mode. Also if the EXEN2
(T2 external enable flag) is set, a 1-to-0 transition in T2EX
(Timer/counter 2 trigger input) will set EXF2 (T2 external flag) but
will not cause a reload from (RCAP2H, RCAP2L) to (TH2,TL2).
Therefore when Timer 2 is in use as a baud rate generator, T2EX
can be used as an additional external interrupt, if needed.
Figure 6 shows the Timer 2 in baud rate generation mode. The baud
rate generation mode is like the auto-reload mode,in that a rollover in
TH2 causes the Timer 2 registers to be reloaded with the 16-bit value
in registers RCAP2H and RCAP2L, which are preset by software.
13
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
When Timer 2 is in the baud rate generator mode, one should not try
to read or write TH2 and TL2. As a baud rate generator, Timer 2 is
incremented every state time (osc/2) or asynchronously from pin T2;
under these conditions, a read or write of TH2 or TL2 may not be
accurate. The RCAP2 registers may be read, but should not be
written to, because a write might overlap a reload and cause write
and/or reload errors. The timer should be turned off (clear TR2)
before accessing the Timer 2 or RCAP2 registers.
If Timer 2 is being clocked internally, the baud rate is:
fOSC
Baud Rate +
[ n * [65536 + (RCAP2H, RCAP2L)]]
* n =
16 in 6 clock mode
32 in 12 clock mode
Where f
= Oscillator Frequency
OSC
To obtain the reload value for RCAP2H and RCAP2L, the above
equation can be rewritten as:
Table 3 shows commonly used baud rates and how they can be
obtained from Timer 2.
fOSC
RCAP2H, RCAP2L + 65536 + ǒ
Ǔ
Summary of Baud Rate Equations
Timer 2 is in baud rate generating mode. If Timer 2 is being clocked
through pin T2(P1.0) the baud rate is:
n * Baud Rate
Timer/Counter 2 Set-up
Timer 2 Overflow Rate
Except for the baud rate generator mode, the values given for T2CON
do not include the setting of the TR2 bit. Therefore, bit TR2 must be
set, separately, to turn the timer on. see Table 4 for set-up of Timer 2
as a timer. Also see Table 5 for set-up of Timer 2 as a counter.
Baud Rate +
16
Table 4. Timer 2 as a Timer
T2CON
MODE
INTERNAL CONTROL
(Note 1)
EXTERNAL CONTROL
(Note 2)
16-bit Auto-Reload
00H
01H
34H
24H
14H
08H
09H
36H
26H
16H
16-bit Capture
Baud rate generator receive and transmit same baud rate
Receive only
Transmit only
Table 5. Timer 2 as a Counter
TMOD
MODE
INTERNAL CONTROL
(Note 1)
EXTERNAL CONTROL
(Note 2)
16-bit
02H
03H
0AH
0BH
Auto-Reload
NOTES:
1. Capture/reload occurs only on timer/counter overflow.
2. Capture/reload occurs on timer/counter overflow and a 1-to-0 transition on T2EX (P1.1) pin except when Timer 2 is used in the baud rate
generator mode.
14
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
Slave 1
SADDR
SADEN
Given
=
=
=
1100 0000
1111 1110
1100 000X
Enhanced UART
The UART operates in all of the usual modes that are described in
the first section of Data Handbook IC20, 80C51-Based 8-Bit
Microcontrollers. In addition the UART can perform framing error
In the above example SADDR is the same and the SADEN data is
used to differentiate between the two slaves. Slave 0 requires a 0 in
bit 0 and it ignores bit 1. Slave 1 requires a 0 in bit 1 and bit 0 is
ignored. A unique address for Slave 0 would be 1100 0010 since
slave 1 requires a 0 in bit 1. A unique address for slave 1 would be
1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be
selected at the same time by an address which has bit 0 = 0 (for
slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed
with 1100 0000.
detect by looking for missing stop bits, and automatic address
recognition. The UART also fully supports multiprocessor
communication as does the standard 80C51 UART.
When used for framing error detect the UART looks for missing stop
bits in the communication. A missing bit will set the FE bit in the
SCON register. The FE bit shares the SCON.7 bit with SM0 and the
function of SCON.7 is determined by PCON.6 (SMOD0) (see
Figure 7). If SMOD0 is set then SCON.7 functions as FE. SCON.7
functions as SM0 when SMOD0 is cleared. When used as FE
SCON.7 can only be cleared by software. Refer to Figure 8.
In a more complex system the following could be used to select
slaves 1 and 2 while excluding slave 0:
Automatic Address Recognition
Slave 0
Slave 1
Slave 2
SADDR
SADEN
Given
=
=
=
1100 0000
1111 1001
1100 0XX0
Automatic Address Recognition is a feature which allows the UART
to recognize certain addresses in the serial bit stream by using
hardware to make the comparisons. This feature saves a great deal
of software overhead by eliminating the need for the software to
examine every serial address which passes by the serial port. This
feature is enabled by setting the SM2 bit in SCON. In the 9 bit UART
modes, mode 2 and mode 3, the Receive Interrupt flag (RI) will be
automatically set when the received byte contains either the “Given”
address or the “Broadcast” address. The 9-bit mode requires that
the 9th information bit is a 1 to indicate that the received information
is an address and not data. Automatic address recognition is shown
in Figure 9.
SADDR
SADEN
Given
=
=
=
1110 0000
1111 1010
1110 0X0X
SADDR
SADEN
Given
=
=
=
1110 0000
1111 1100
1110 00XX
In the above example the differentiation among the 3 slaves is in the
lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be
uniquely addressed by 1110 0110. Slave 1 requires that bit 1 = 0 and
it can be uniquely addressed by 1110 and 0101. Slave 2 requires
that bit 2 = 0 and its unique address is 1110 0011. To select Slaves 0
and 1 and exclude Slave 2 use address 1110 0100, since it is
necessary to make bit 2 = 1 to exclude slave 2.
The 8 bit mode is called Mode 1. In this mode the RI flag will be set
if SM2 is enabled and the information received has a valid stop bit
following the 8 address bits and the information is either a Given or
Broadcast address.
Mode 0 is the Shift Register mode and SM2 is ignored.
The Broadcast Address for each slave is created by taking the
logical OR of SADDR and SADEN. Zeros in this result are trended
as don’t-cares. In most cases, interpreting the don’t-cares as ones,
the broadcast address will be FF hexadecimal.
Using the Automatic Address Recognition feature allows a master to
selectively communicate with one or more slaves by invoking the
Given slave address or addresses. All of the slaves may be
contacted by using the Broadcast address. Two special Function
Registers are used to define the slave’s address, SADDR, and the
address mask, SADEN. SADEN is used to define which bits in the
SADDR are to b used and which bits are “don’t care”. The SADEN
mask can be logically ANDed with the SADDR to create the “Given”
address which the master will use for addressing each of the slaves.
Use of the Given address allows multiple slaves to be recognized
while excluding others. The following examples will help to show the
versatility of this scheme:
Upon reset SADDR (SFR address 0A9H) and SADEN (SFR
address 0B9H) are leaded with 0s. This produces a given address
of all “don’t cares” as well as a Broadcast address of all “don’t
cares”. This effectively disables the Automatic Addressing mode and
allows the microcontroller to use standard 80C51 type UART drivers
which do not make use of this feature.
Slave 0
SADDR
SADEN
Given
=
=
=
1100 0000
1111 1101
1100 00X0
15
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
SCON Address = 98H
Reset Value = 0000 0000B
Bit Addressable
SM0/FE
SM1
SM2
REN
TB8
RB8
Tl
Rl
Bit:
7
6
5
4
3
2
1
0
(SMOD0 = 0/1)*
Symbol
FE
Function
Framing Error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid
frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit.
SM0
SM1
Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0)
Serial Port Mode Bit 1
SM0
SM1
Mode
Description
Baud Rate**
0
0
1
0
1
0
0
1
2
shift register
8-bit UART
9-bit UART
f
/6 (6-clock mode) or f
/12 (12-clock mode)
OSC
OSC
variable
f
f
/32 or f
/64 or f
/16 (6-clock mode) or
/32 (12-clock mode)
OSC
OSC
OSC
OSC
1
1
3
9-bit UART
variable
SM2
Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the
received 9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address.
In Mode 1, if SM2 = 1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a
Given or Broadcast Address. In Mode 0, SM2 should be 0.
REN
TB8
RB8
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired.
In modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received.
In Mode 0, RB8 is not used.
Tl
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the
other modes, in any serial transmission. Must be cleared by software.
Rl
Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in
the other modes, in any serial reception (except see SM2). Must be cleared by software.
NOTE:
*SMOD0 is located at PCON6.
**f = oscillator frequency
OSC
SU01255
Figure 7. SCON: Serial Port Control Register
16
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
D0
D1
D2
D3
D4
D5
D6
D7
D8
START
BIT
DATA BYTE
ONLY IN
MODE 2, 3
STOP
BIT
SET FE BIT IF STOP BIT IS 0 (FRAMING ERROR)
SM0 TO UART MODE CONTROL
SCON
(98H)
SM0 / FE
SMOD1
SM1
SM2
REN
POF
TB8
LVF
RB8
GF0
TI
RI
PCON
(87H)
SMOD0
–
GF1
IDL
0 : SCON.7 = SM0
1 : SCON.7 = FE
SU00044
Figure 8. UART Framing Error Detection
D0
D1
D2
D3
D4
D5
D6
D7
D8
SCON
(98H)
SM0
SM1
SM2
REN
1
TB8
X
RB8
TI
RI
1
1
1
0
1
RECEIVED ADDRESS D0 TO D7
PROGRAMMED ADDRESS
COMPARATOR
IN UART MODE 2 OR MODE 3 AND SM2 = 1:
INTERRUPT IF REN=1, RB8=1 AND “RECEIVED ADDRESS” = “PROGRAMMED ADDRESS”
– WHEN OWN ADDRESS RECEIVED, CLEAR SM2 TO RECEIVE DATA BYTES
– WHEN ALL DATA BYTES HAVE BEEN RECEIVED: SET SM2 TO WAIT FOR NEXT ADDRESS.
SU00045
Figure 9. UART Multiprocessor Communication, Automatic Address Recognition
17
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
The priority scheme for servicing the interrupts is the same as that
for the 80C51, except there are four interrupt levels rather than two
as on the 80C51. An interrupt will be serviced as long as an interrupt
of equal or higher priority is not already being serviced. If an
interrupt of equal or higher level priority is being serviced, the new
interrupt will wait until it is finished before being serviced. If a lower
priority level interrupt is being serviced, it will be stopped and the
new interrupt serviced. When the new interrupt is finished, the lower
priority level interrupt that was stopped will be completed.
Interrupt Priority Structure
The P89C51RB2/RC2/RD2Hxx has a 7 source four-level interrupt
structure (see Table 6).
There are 3 SFRs associated with the four-level interrupt. They are
the IE, IP, and IPH. (See Figures 10, 11, and 12.) The IPH (Interrupt
Priority High) register makes the four-level interrupt structure
possible. The IPH is located at SFR address B7H. The structure of
the IPH register and a description of its bits is shown in Figure 12.
The function of the IPH SFR, when combined with the IP SFR,
determines the priority of each interrupt. The priority of each
interrupt is determined as shown in the following table:
PRIORITY BITS
INTERRUPT PRIORITY LEVEL
IPH.x
IP.x
0
0
0
1
1
Level 0 (lowest priority)
Level 1
1
0
Level 2
1
Level 3 (highest priority)
Table 6.
Interrupt Table
SOURCE
POLLING PRIORITY
REQUEST BITS
HARDWARE CLEAR?
VECTOR ADDRESS
1
2
X0
T0
1
2
3
4
5
IE0
TP0
IE1
N (L) Y (T)
03H
0BH
13H
1BH
33H
Y
X1
N (L) Y (T)
T1
TF1
Y
N
PCA
CF, CCFn
n = 0–4
SP
T2
6
7
RI, TI
N
N
23H
2BH
TF2, EXF2
NOTES:
1. L = Level activated
2. T = Transition activated
7
6
5
4
3
2
1
0
IE (0A8H)
EA
EC
ET2
ES
ET1
EX1
ET0
EX0
Enable Bit = 1 enables the interrupt.
Enable Bit = 0 disables it.
BIT
SYMBOL FUNCTION
IE.7
EA
Global disable bit. If EA = 0, all interrupts are disabled. If EA = 1, each interrupt can be individually
enabled or disabled by setting or clearing its enable bit.
PCA interrupt enable bit
Timer 2 interrupt enable bit.
Serial Port interrupt enable bit.
Timer 1 interrupt enable bit.
External interrupt 1 enable bit.
Timer 0 interrupt enable bit.
IE.6
IE.5
IE.4
IE.3
IE.2
IE.1
IE.0
EC
ET2
ES
ET1
EX1
ET0
EX0
External interrupt 0 enable bit.
SU01290
Figure 10. IE Registers
18
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
7
6
5
4
3
2
1
0
IP (0B8H)
–
PPC
PT2
PS
PT1
PX1
PT0
PX0
Priority Bit = 1 assigns high priority
Priority Bit = 0 assigns low priority
BIT
IP.7
IP.6
IP.5
IP.4
IP.3
IP.2
IP.1
IP.0
SYMBOL FUNCTION
–
–
PPC
PT2
PS
PT1
PX1
PT0
PX0
PCA interrupt priority bit
Timer 2 interrupt priority bit.
Serial Port interrupt priority bit.
Timer 1 interrupt priority bit.
External interrupt 1 priority bit.
Timer 0 interrupt priority bit.
External interrupt 0 priority bit.
SU01291
Figure 11. IP Registers
7
6
5
4
3
2
1
0
IPH (B7H)
–
PPCH
PT2H
PSH
PT1H
PX1H
PT0H
PX0H
Priority Bit = 1 assigns higher priority
Priority Bit = 0 assigns lower priority
BIT
SYMBOL FUNCTION
IPH.7
IPH.6
IPH.5
IPH.4
IPH.3
IPH.2
IPH.1
IPH.0
–
–
PPCH
PT2H
PSH
PT1H
PX1H
PT0H
PX0H
PCA interrupt priority bit
Timer 2 interrupt priority bit high.
Serial Port interrupt priority bit high.
Timer 1 interrupt priority bit high.
External interrupt 1 priority bit high.
Timer 0 interrupt priority bit high.
External interrupt 0 priority bit high.
SU01292
Figure 12. IPH Registers
19
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
be quickly toggled simply by executing an INC AUXR1 instruction
without affecting the GF2 bit.
Reduced EMI Mode
The AO bit (AUXR.0) in the AUXR register when set disables the
ALE output.
The ENBOOT bit determines whether the BOOTROM is enabled
or disabled. This bit will automatically be set if the status byte is
non zero during reset or PSEN is pulled low, ALE floats high, and
Reduced EMI Mode
EA > V on the falling edge of reset. Otherwise, this bit will be
cleared during reset.
IH
AUXR (8EH)
7
–
6
–
5
–
4
–
3
–
2
–
1
0
EXTRAM
AO
AUXR.1
AUXR.0
EXTRAM
AO
DPS
BIT0
Turns off ALE output.
AUXR1
DPTR1
DPTR0
Dual DPTR
DPH
DPL
The dual DPTR structure (see Figure 13) is a way by which the chip
will specify the address of an external data memory location. There
are two 16-bit DPTR registers that address the external memory,
and a single bit called DPS = AUXR1/bit0 that allows the program
code to switch between them.
(83H)
(82H)
EXTERNAL
DATA
MEMORY
SU00745A
Figure 13.
• New Register Name: AUXR1#
• SFR Address: A2H
DPTR Instructions
• Reset Value: xxxxxxx0B
The instructions that refer to DPTR refer to the data pointer that is
currently selected using the AUXR1/bit 0 register. The six
instructions that use the DPTR are as follows:
AUXR1 (A2H)
7
–
6
–
5
4
–
3
2
0
1
–
0
INC DPTR
Increments the data pointer by 1
ENBOOT
GF2
DPS
MOV DPTR, #data16 Loads the DPTR with a 16-bit constant
Where:
DPS = AUXR1/bit0 = Switches between DPTR0 and DPTR1.
MOV A, @ A+DPTR
MOVX A, @ DPTR
Move code byte relative to DPTR to ACC
Move external RAM (16-bit address) to
ACC
Select Reg
DPS
DPTR0
DPTR1
0
1
MOVX @ DPTR , A
JMP @ A + DPTR
Move ACC to external RAM (16-bit
address)
Jump indirect relative to DPTR
The DPS bit status should be saved by software when switching
between DPTR0 and DPTR1.
The data pointer can be accessed on a byte-by-byte basis by
specifying the low or high byte in an instruction which accesses the
SFRs. See Application Note AN458 for more details.
The GF2 bit is a general purpose user-defined flag. Note that bit 2 is
not writable and is always read as a zero. This allows the DPS bit to
20
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
PCA is shut off by clearing this bit. The CF bit (CCON.7) is set when
the PCA counter overflows and an interrupt will be generated if the
ECF bit in the CMOD register is set, The CF bit can only be cleared
by software. Bits 0 through 4 of the CCON register are the flags for
the modules (bit 0 for module 0, bit 1 for module 1, etc.) and are set
by hardware when either a match or a capture occurs. These flags
also can only be cleared by software. The PCA interrupt system
shown in Figure 16.
Programmable Counter Array (PCA)
The Programmable Counter Array available on the
P89C51RB2/RC2/RD2Hxx is a special 16-bit Timer that has five
16-bit capture/compare modules associated with it. Each of the
modules can be programmed to operate in one of four modes: rising
and/or falling edge capture, software timer, high-speed output, or
pulse width modulator. Each module has a pin associated with it in
port 1. Module 0 is connected to P1.3(CEX0), module 1 to
P1.4(CEX1), etc. The basic PCA configuration is shown in Figure
14.
Each module in the PCA has a special function register associated
with it. These registers are: CCAPM0 for module 0, CCAPM1 for
module 1, etc. (see Figure 19). The registers contain the bits that
control the mode that each module will operate in. The ECCF bit
(CCAPMn.0 where n=0, 1, 2, 3, or 4 depending on the module)
enables the CCF flag in the CCON SFR to generate an interrupt
when a match or compare occurs in the associated module. PWM
(CCAPMn.1) enables the pulse width modulation mode. The TOG
bit (CCAPMn.2) when set causes the CEX output associated with
the module to toggle when there is a match between the PCA
counter and the module’s capture/compare register. The match bit
MAT (CCAPMn.3) when set will cause the CCFn bit in the CCON
register to be set when there is a match between the PCA counter
and the module’s capture/compare register.
The PCA timer is a common time base for all five modules and can
be programmed to run at: 1/6 the oscillator frequency, 1/2 the
oscillator frequency, the Timer 0 overflow, or the input on the ECI pin
(P1.2). The timer count source is determined from the CPS1 and
CPS0 bits in the CMOD SFR as follows (see Figure 17):
CPS1 CPS0 PCA Timer Count Source
0
0
1/6 oscillator frequency (6 clock mode);
1/12 oscillator frequency (12 clock mode)
1/2 oscillator frequency (6 clock mode);
1/4 oscillator frequency (12 clock mode)
Timer 0 overflow
0
1
1
1
0
1
External Input at ECI pin
The next two bits CAPN (CCAPMn.4) and CAPP (CCAPMn.5)
determine the edge that a capture input will be active on. The CAPN
bit enables the negative edge, and the CAPP bit enables the positive
edge. If both bits are set both edges will be enabled and a capture will
occur for either transition. The last bit in the register ECOM
In the CMOD SFR are three additional bits associated with the PCA.
They are CIDL which allows the PCA to stop during idle mode,
WDTE which enables or disables the watchdog function on
module 4, and ECF which when set causes an interrupt and the
PCA overflow flag CF (in the CCON SFR) to be set when the PCA
timer overflows. These functions are shown in Figure 15.
(CCAPMn.6) when set enables the comparator function. Figure 20
shows the CCAPMn settings for the various PCA functions.
The watchdog timer function is implemented in module 4 (see
Figure 24).
There are two additional registers associated with each of the PCA
modules. They are CCAPnH and CCAPnL and these are the
registers that store the 16-bit count when a capture occurs or a
compare should occur. When a module is used in the PWM mode
these registers are used to control the duty cycle of the output.
The CCON SFR contains the run control bit for the PCA and the
flags for the PCA timer (CF) and each module (refer to Figure 18).
To run the PCA the CR bit (CCON.6) must be set by software. The
16 BITS
P1.3/CEX0
P1.4/CEX1
P1.5/CEX2
P1.6/CEX3
MODULE 0
MODULE 1
MODULE 2
MODULE 3
MODULE 4
16 BITS
PCA TIMER/COUNTER
TIME BASE FOR PCA MODULES
MODULE FUNCTIONS:
16-BIT CAPTURE
16-BIT TIMER
P1.7/CEX4
SU00032
16-BIT HIGH SPEED OUTPUT
8-BIT PWM
WATCHDOG TIMER (MODULE 4 ONLY)
Figure 14. Programmable Counter Array (PCA)
21
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
TO PCA
MODULES
OSC/6 (6 CLOCK MODE)
OR
OSC/12 (12 CLOCK MODE)
OSC/2 (6 CLOCK MODE)
OR
OSC/4 (12 CLOCK MODE)
OVERFLOW
INTERRUPT
CH
CL
16–BIT UP COUNTER
TIMER 0 OVERFLOW
EXTERNAL INPUT
(P1.2/ECI)
00
01
10
11
DECODE
IDLE
CMOD
(C1H)
CIDL
CF
WDTE
––
––
––
––
CPS1
CCF2
CPS0
ECF
CCON
(C0H)
CR
CCF4
CCF3
CCF1
CCF0
SU01256
Figure 15. PCA Timer/Counter
CCON
(C0H)
CF
CR
––
CCF4
CCF3
CCF2
CCF1
CCF0
PCA TIMER/COUNTER
MODULE 0
IE.7
EA
IE.6
EC
TO
MODULE 1
MODULE 2
INTERRUPT
PRIORITY
DECODER
MODULE 3
MODULE 4
CCAPMn.0
ECCFn
CMOD.0
ECF
SU01097
Figure 16. PCA Interrupt System
22
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
CMOD Address = D9H
Reset Value = 00XX X000B
CIDL
WDTE
–
–
–
CPS1
CPS0
ECF
Bit:
Function
7
6
5
4
3
2
1
0
Symbol
CIDL
Counter Idle control: CIDL = 0 programs the PCA Counter to continue functioning during idle Mode. CIDL = 1 programs
it to be gated off during idle.
WDTE
–
Watchdog Timer Enable: WDTE = 0 disables Watchdog Timer function on PCA Module 4. WDTE = 1 enables it.
Not implemented, reserved for future use.*
CPS1
CPS0
PCA Count Pulse Select bit 1.
PCA Count Pulse Select bit 0.
CPS1
CPS0
Selected PCA Input**
0
0
1
1
0
1
0
1
0
1
2
3
Internal clock, f
/6 in 6-clock mode (f
/2 in 6-clock mode (f
/12 in 12-clock mode)
/4 in 12-clock mode)
OSC
OSC
OSC
Internal clock, f
OSC
Timer 0 overflow
External clock at ECI/P1.2 pin
(max. rate = f /4 in 6-clock mode, f
/8 in 12-clock mode)
OCS
OSC
ECF
PCA Enable Counter Overflow interrupt: ECF = 1 enables CF bit in CCON to generate an interrupt. ECF = 0 disables
that function of CF.
NOTE:
*
User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive
value of the new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.
**
f
= oscillator frequency
OSC
SU01318
Figure 17. CMOD: PCA Counter Mode Register
CCON Address = D8H
Bit Addressable
CF
Reset Value = 00X0 0000B
CR
–
CCF4
CCF3
CCF2
CCF1
CCF0
Bit:
7
6
5
4
3
2
1
0
Symbol
CF
Function
PCA Counter Overflow flag. Set by hardware when the counter rolls over. CF flags an interrupt if bit ECF in CMOD is
set. CF may be set by either hardware or software but can only be cleared by software.
CR
PCA Counter Run control bit. Set by software to turn the PCA counter on. Must be cleared by software to turn the PCA
counter off.
–
Not implemented, reserved for future use*.
CCF4
CCF3
CCF2
CCF1
CCF0
PCA Module 4 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
PCA Module 3 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
PCA Module 2 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
PCA Module 1 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
PCA Module 0 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
NOTE:
*
User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive
value of the new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.
SU01319
Figure 18. CCON: PCA Counter Control Register
23
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
CCAPMn Address
CCAPM0
CCAPM1
CCAPM2
CCAPM3
CCAPM4
0DAH
0DBH
0DCH
0DDH
0DEH
Reset Value = X000 0000B
Not Bit Addressable
–
ECOMn CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
Bit:
7
6
5
4
3
2
1
0
Symbol
Function
–
Not implemented, reserved for future use*.
ECOMn
CAPPn
CAPNn
MATn
Enable Comparator. ECOMn = 1 enables the comparator function.
Capture Positive, CAPPn = 1 enables positive edge capture.
Capture Negative, CAPNn = 1 enables negative edge capture.
Match. When MATn = 1, a match of the PCA counter with this module’s compare/capture register causes the CCFn bit
in CCON to be set, flagging an interrupt.
TOGn
Toggle. When TOGn = 1, a match of the PCA counter with this module’s compare/capture register causes the CEXn
pin to toggle.
PWMn
ECCFn
Pulse Width Modulation Mode. PWMn = 1 enables the CEXn pin to be used as a pulse width modulated output.
Enable CCF interrupt. Enables compare/capture flag CCFn in the CCON register to generate an interrupt.
NOTE:
*User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features In that case, the reset or inactive
value of the new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.
SU01320
Figure 19. CCAPMn: PCA Modules Compare/Capture Registers
–
X
X
X
X
X
X
X
X
ECOMn CAPPn CAPNn
MATn
TOGn
PWMn
ECCFn
MODULE FUNCTION
0
X
X
X
1
1
1
1
0
1
0
1
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
1
1
0
1
0
0
0
0
0
1
0
X
0
0
0
0
0
0
1
0
0
X
X
X
X
X
0
No operation
16-bit capture by a positive-edge trigger on CEXn
16-bit capture by a negative trigger on CEXn
16-bit capture by a transition on CEXn
16-bit Software Timer
16-bit High Speed Output
8-bit PWM
X
Watchdog Timer
Figure 20. PCA Module Modes (CCAPMn Register)
PCA Capture Mode
counter and the module’s capture registers. To activate this mode
the TOG, MAT, and ECOM bits in the module’s CCAPMn SFR must
be set (see Figure 23).
To use one of the PCA modules in the capture mode either one or
both of the CCAPM bits CAPN and CAPP for that module must be
set. The external CEX input for the module (on port 1) is sampled for
a transition. When a valid transition occurs the PCA hardware loads
the value of the PCA counter registers (CH and CL) into the
module’s capture registers (CCAPnL and CCAPnH). If the CCFn bit
for the module in the CCON SFR and the ECCFn bit in the CCAPMn
SFR are set then an interrupt will be generated. Refer to Figure 21.
Pulse Width Modulator Mode
All of the PCA modules can be used as PWM outputs. Figure 24
shows the PWM function. The frequency of the output depends on
the source for the PCA timer. All of the modules will have the same
frequency of output because they all share the PCA timer. The duty
cycle of each module is independently variable using the module’s
capture register CCAPLn. When the value of the PCA CL SFR is
less than the value in the module’s CCAPLn SFR the output will be
low, when it is equal to or greater than the output will be high. When
CL overflows from FF to 00, CCAPLn is reloaded with the value in
CCAPHn. the allows updating the PWM without glitches. The PWM
and ECOM bits in the module’s CCAPMn register must be set to
enable the PWM mode.
16-bit Software Timer Mode
The PCA modules can be used as software timers by setting both
the ECOM and MAT bits in the modules CCAPMn register. The PCA
timer will be compared to the module’s capture registers and when a
match occurs an interrupt will occur if the CCFn (CCON SFR) and
the ECCFn (CCAPMn SFR) bits for the module are both set (see
Figure 22).
High Speed Output Mode
In this mode the CEX output (on port 1) associated with the PCA
module will toggle each time a match occurs between the PCA
24
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
CCON
CF
CR
––
CCF4
CCF3
CCF2
CCF1
CCF0
(D8H)
PCA INTERRUPT
(TO CCFn)
PCA TIMER/COUNTER
CH
CL
CAPTURE
CEXn
CCAPnH
CCAPnL
CCAPMn, n= 0 to 4
(DAH–DEH)
––
ECOMn
0
CAPPn
CAPNn
MATn
0
TOGn
0
PWMn
ECCFn
0
SU01507
Figure 21. PCA Capture Mode
CCON
(D8H)
CF
CR
––
CCF4
CCF3
CCF2
CCF1
CCF0
WRITE TO
CCAPnH
RESET
PCA INTERRUPT
CCAPnH
CCAPnL
WRITE TO
CCAPnL
(TO CCFn)
0
1
ENABLE
MATCH
16–BIT COMPARATOR
CH
CL
PCA TIMER/COUNTER
CCAPMn, n= 0 to 4
(DAH–DEH)
––
ECOMn
CAPPn
0
CAPNn
0
MATn
TOGn
0
PWMn
0
ECCFn
SU01508
Figure 22. PCA Compare Mode
25
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
CCON
(D8H)
CF
CR
––
CCF4
CCF3
CCF2
CCF1
CCF0
WRITE TO
CCAPnH
RESET
PCA INTERRUPT
CCAPnH
CCAPnL
WRITE TO
CCAPnL
(TO CCFn)
0
1
MATCH
ENABLE
16–BIT COMPARATOR
TOGGLE
CEXn
CH
CL
PCA TIMER/COUNTER
CCAPMn, n: 0..4
(DAH–DEH)
––
ECOMn
CAPPn
0
CAPNn
0
MATn
TOGn
PWMn
0
ECCFn
1
SU01509
Figure 23. PCA High Speed Output Mode
CCAPnH
CCAPnL
0
CL < CCAPnL
ENABLE
8–BIT
CEXn
COMPARATOR
CL >= CCAPnL
1
CL
OVERFLOW
PCA TIMER/COUNTER
CCAPMn, n: 0..4
(DAH–DEH)
––
ECOMn
CAPPn
0
CAPNn
MATn
0
TOGn
0
PWMn
ECCFn
0
0
SU01510
Figure 24. PCA PWM Mode
26
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
CMOD
(D9H)
CIDL
WDTE
––
––
MODULE 4
MATCH
––
CPS1
CPS0
ECF
WRITE TO
CCAP4L
RESET
CCAP4H
CCAP4L
WRITE TO
CCAP4H
1
0
ENABLE
16–BIT COMPARATOR
RESET
CH
CL
PCA TIMER/COUNTER
CCAPM4
(DEH)
––
ECOMn
CAPPn
0
CAPNn
0
MATn
1
TOGn
X
PWMn
0
ECCFn
X
SU01511
Figure 25. PCA Watchdog Timer mode (Module 4 only)
PCA Watchdog Timer
The first two options are more reliable because the watchdog
timer is never disabled as in option #3. If the program counter ever
goes astray, a match will eventually occur and cause an internal
reset. The second option is also not recommended if other PCA
modules are being used. Remember, the PCA timer is the time
base for all modules; changing the time base for other modules
would not be a good idea. Thus, in most applications the first
solution is the best option.
An on-board watchdog timer is available with the PCA to improve the
reliability of the system without increasing chip count. Watchdog
timers are useful for systems that are susceptible to noise, power
glitches, or electrostatic discharge. Module 4 is the only PCA module
that can be programmed as a watchdog. However, this module can
still be used for other modes if the watchdog is not needed.
Figure 25 shows a diagram of how the watchdog works. The user
pre-loads a 16-bit value in the compare registers. Just like the other
compare modes, this 16-bit value is compared to the PCA timer
value. If a match is allowed to occur, an internal reset will be
generated. This will not cause the RST pin to be driven high.
Figure 26 shows the code for initializing the watchdog timer.
Module 4 can be configured in either compare mode, and the WDTE
bit in CMOD must also be set. The user’s software then must
periodically change (CCAP4H,CCAP4L) to keep a match from
occurring with the PCA timer (CH,CL). This code is given in the
WATCHDOG routine in Figure 26.
In order to hold off the reset, the user has three options:
1. periodically change the compare value so it will never match the
PCA timer,
This routine should not be part of an interrupt service routine,
because if the program counter goes astray and gets stuck in an
infinite loop, interrupts will still be serviced and the watchdog will
keep getting reset. Thus, the purpose of the watchdog would be
2. periodically change the PCA timer value so it will never match
the compare values, or
3. disable the watchdog by clearing the WDTE bit before a match
occurs and then re-enable it.
defeated. Instead, call this subroutine from the main program within
16
2
count of the PCA timer.
27
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
INIT_WATCHDOG:
MOV CCAPM4, #4CH
MOV CCAP4L, #0FFH
MOV CCAP4H, #0FFH
; Module 4 in compare mode
; Write to low byte first
; Before PCA timer counts up to
; FFFF Hex, these compare values
; must be changed
ORL CMOD, #40H
; Set the WDTE bit to enable the
; watchdog timer without changing
; the other bits in CMOD
;
;********************************************************************
;
; Main program goes here, but CALL WATCHDOG periodically.
;
;********************************************************************
;
WATCHDOG:
CLR EA
; Hold off interrupts
MOV CCAP4L, #00
MOV CCAP4H, CH
SETB EA
; Next compare value is within
; 255 counts of the current PCA
; timer value
RET
Figure 26. PCA Watchdog Timer Initialization Code
28
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
For example:
MOV @R0,acc
Expanded Data RAM Addressing
The P89C51RB2/RC2/RD2Hxx has internal data memory that is
mapped into four separate segments: the lower 128 bytes of RAM,
upper 128 bytes of RAM, 128 bytes Special Function Register (SFR),
and 256 bytes expanded RAM (ERAM) (768 bytes for the RD2).
where R0 contains 0A0H, accesses the data byte at address 0A0H,
rather than P2 (whose address is 0A0H).
The ERAM can be accessed by indirect addressing, with EXTRAM
bit cleared and MOVX instructions. This part of memory is physically
located on-chip, logically occupies the first 256/768-bytes of external
data memory in the P89C51RB2/RC2/P89C51RD2
The four segments are:
1. The Lower 128 bytes of RAM (addresses 00H to 7FH) are
directly and indirectly addressable.
2. The Upper 128 bytes of RAM (addresses 80H to FFH) are
indirectly addressable only.
With EXTRAM = 0, the ERAM is indirectly addressed, using the
MOVX instruction in combination with any of the registers R0, R1 of
the selected bank or DPTR. An access to ERAM will not affect ports
P0, P3.6 (WR#) and P3.7 (RD#). P2 SFR is output during external
addressing. For example, with EXTRAM = 0,
3. The Special Function Registers, SFRs, (addresses 80H to FFH)
are directly addressable only.
4. The 256/768-bytes expanded RAM (ERAM, 00H – 1FFH/2FFH)
are indirectly accessed by move external instruction, MOVX, and
with the EXTRAM bit cleared, see Figure 27.
MOVX @R0,acc
where R0 contains 0A0H, access the ERAM at address 0A0H rather
than external memory. An access to external data memory locations
higher than the ERAM will be performed with the MOVX DPTR
instructions in the same way as in the standard 80C51, so with P0
and P2 as data/address bus, and P3.6 and P3.7 as write and read
timing signals. Refer to Figure 28.
The Lower 128 bytes can be accessed by either direct or indirect
addressing. The Upper 128 bytes can be accessed by indirect
addressing only. The Upper 128 bytes occupy the same address
space as the SFR. That means they have the same address, but are
physically separate from SFR space.
With EXTRAM = 1, MOVX @Ri and MOVX @DPTR will be similar
to the standard 80C51. MOVX @ Ri will provide an 8-bit address
multiplexed with data on Port 0 and any output port pins can be
used to output higher order address bits. This is to provide the
external paging capability. MOVX @DPTR will generate a 16-bit
address. Port 2 outputs the high-order eight address bits (the
contents of DPH) while Port 0 multiplexes the low-order eight
address bits (DPL) with data. MOVX @Ri and MOVX @DPTR will
generate either read or write signals on P3.6 (WR) and P3.7 (RD).
When an instruction accesses an internal location above address
7FH, the CPU knows whether the access is to the upper 128 bytes
of data RAM or to SFR space by the addressing mode used in the
instruction. Instructions that use direct addressing access SFR
space. For example:
MOV 0A0H,#data
accesses the SFR at location 0A0H (which is P2). Instructions that
use indirect addressing access the Upper 128 bytes of data RAM.
The stack pointer (SP) may be located anywhere in the 256 bytes
RAM (lower and upper RAM) internal data memory. The stack may
not be located in the ERAM.
AUXR
Address = 8EH
Reset Value = xxxx xx00B
Not Bit Addressable
—
—
6
—
5
—
4
—
3
—
2
EXTRAM
AO
Bit:
Function
Disable/Enable ALE
7
1
0
Symbol
AO
AO
Operating Mode
1
1
0
ALE is emitted at a constant rate of / the oscillator frequency (6 clock mode; / f
in 12 clock mode).
3
6
OSC
1
ALE is active only during a MOVX or MOVC instruction.
EXTRAM
Internal/External RAM access using MOVX @Ri/@DPTR
EXTRAM
Operating Mode
0
1
Internal ERAM access using MOVX @Ri/@DPTR
External data memory access.
—
Not implemented, reserved for future use*.
NOTE:
*User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the new
bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.
SU01258
Figure 27. AUXR: Auxiliary Register
29
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
FF
FF
FFFF
UPPER
128 BYTES
INTERNAL RAM
SPECIAL
FUNCTION
REGISTER
EXTERNAL
DATA
MEMORY
80
80
ERAM
256 or 768 BYTES
LOWER
128 BYTES
INTERNAL RAM
100
00
00
0000
SU01293
Figure 28. Internal and External Data Memory Address Space with EXTRAM = 0
HARDWARE WATCHDOG TIMER (ONE-TIME ENABLED WITH RESET-OUT FOR P89C51RB2/RC2/RD2Hxx)
The WDT is intended as a recovery method in situations where the CPU may be subjected to software upset. The WDT consists of a 14-bit
counter and the WatchDog Timer reset (WDTRST) SFR. The WDT is disabled at reset. To enable the WDT, user must write 01EH and 0E1H in
sequence to the WDTRST, SFR location 0A6H. When WDT is enabled, it will increment every machine cycle while the oscillator is running and
there is no way to disable the WDT except through reset (either hardware reset or WDT overflow reset). When WDT overflows, it will drive an
output reset HIGH pulse at the RST-pin (see the note below).
Using the WDT
To enable the WDT, user must write 01EH and 0E1H in sequence to the WDTRST, SFR location 0A6H. When WDT is enabled, the user needs to
service it by writing 01EH and 0E1H to WDTRST to avoid WDT overflow. The 14-bit counter overflows when it reaches 16383 (3FFFH) and this
will reset the device. When WDT is enabled, it will increment every machine cycle while the oscillator is running. This means the user must reset
the WDT at least every 16383 machine cycles. To reset the WDT, the user must write 01EH and 0E1H to WDTRST. WDTRST is a write only
register. The WDT counter cannot be read or written. When WDT overflows, it will generate an output RESET pulse at the reset pin (see note
below). The RESET pulse duration is 98 × T
(6 clock mode; 196 in 12 clock mode), where T
= 1/f . To make the best use of the WDT, it
OSC
OSC
OSC
should be serviced in those sections of code that will periodically be executed within the time required to prevent a WDT reset.
30
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
1, 2, 3
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Operating temperature under bias
RATING
0 to +70 or –40 to +85
–65 to +150
0 to +13.0
–0.5 to +6.5
15
UNIT
°C
°C
V
Storage temperature range
Voltage on EA/V pin to V
PP
SS
Voltage on any other pin to V
V
SS
Maximum I per I/O pin
mA
W
OL
Power dissipation (based on package heat transfer limitations, not device power consumption)
1.5
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section
of this specification is not implied.
2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static
charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.
3. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to V unless otherwise noted.
SS
31
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
DC ELECTRICAL CHARACTERISTICS
T
amb
= 0°C to +70°C; V = 5 V ± 10% or –40°C to +85°C; 5 V ±5%; V = 0 V
CC SS
LIMITS
TEST
CONDITIONS
SYMBOL
PARAMETER
UNIT
1
MIN
TYP
MAX
0.2V –0.1
V
V
V
Input low voltage
4.5 V < V < 5.5 V
–0.5
V
V
V
IL
CC
CC
Input high voltage (ports 0, 1, 2, 3, EA)
Input high voltage, XTAL1, RST
0.2V +0.9
V
CC
V
CC
+0.5
+0.5
IH
CC
0.7V
IH1
CC
V
OL
= 4.5 V
= 1.6 mA
CC
8
V
V
V
V
Output low voltage, ports 1, 2, 3
0.4
V
V
V
OL
2
I
I
V
CC
= 4.5 V
7, 8
Output low voltage, port 0, ALE, PSEN
0.45
OL1
OH
2
= 3.2 mA
OL
V
CC
= 4.5 V
= –30 µA
3
Output high voltage, ports 1, 2, 3
V
V
– 0.7
– 0.7
CC
I
OH
Output high voltage (port 0 in external bus mode),
V
CC
= 4.5 V
= –3.2 mA
V
OH1
CC
9
3
ALE , PSEN
I
OH
I
I
Logical 0 input current, ports 1, 2, 3
Logical 1-to-0 transition current, ports 1, 2, 3
Input leakage current, port 0
V
V
= 0.4 V
= 2.0 V
–1
–75
–650
±10
µA
µA
µA
IL
IN
IN
6
TL
See Note 4
I
I
0.45 < V < V – 0.3
LI
IN
CC
Power supply current (see Figure 36):
Active mode (see Note 5)
See Note 5
CC
Idle mode (see Note 5)
Power-down mode or clock stopped (see
Figure 42 for conditions)
T
= 0°C to 70°C
= –40°C to +85°C
< 1
60
40
50
µA
µA
mA
amb
T
amb
Programming and erase mode
Internal reset pull-down resistor
f
= 20 MHz
osc
R
C
40
225
15
kΩ
RST
IO
10
Pin capacitance (except EA)
pF
NOTES:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5 V.
2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V s of ALE and ports 1 and 3. The noise is due
OL
to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
worst cases (capacitive loading > 100 pF), the noise pulse on the ALE pin may exceed 0.8 V. In such cases, it may be desirable to qualify
ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. I can exceed these conditions provided that no
OL
single output sinks more than 5 mA and no more than two outputs exceed the test conditions.
3. Capacitive loading on ports 0 and 2 may cause the V on ALE and PSEN to momentarily fall below the V –0.7 specification when the
OH
CC
address bits are stabilizing.
4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when V is approximately 2 V.
IN
5. See Figures 39 through 42 for I test conditions and Figure 36 for I vs Freq.
CC
CC
Active mode:
Idle mode:
6. This value applies to T
I
I
= (2.8 × FREQ. + 8)mA in 6 clock mode; (1.4 × FREQ. + 8)mA in 12 clock mode.
= (1.2 × FREQ. +1.0)mA in 6 clock mode; (0.6 × FREQ. +1.0)mA in 12 clock mode.
= 0°C to +70°C.
CC(MAX)
CC(MAX)
amb
7. Load capacitance for port 0, ALE, and PSEN = 100 pF, load capacitance for all other outputs = 80 pF.
8. Under steady state (non-transient) conditions, I must be externally limited as follows:
OL
Maximum I per port pin:
15 mA (*NOTE: This is 85°C specification.)
OL
Maximum I per 8-bit port:
26 mA
71 mA
OL
Maximum total I for all outputs:
OL
If I exceeds the test condition, V may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
OL
OL
test conditions.
9. ALE is tested to V
, except when ALE is off then V is the voltage specification.
OH
OH1
10.Pin capacitance is characterized but not tested. Pin capacitance is less than 25 pF. Pin capacitance of ceramic package is less than 15 pF
(except EA is 25 pF).
32
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
AC ELECTRICAL CHARACTERISTICS (6 CLOCK MODE)
1, 2, 3
T
= 0°C to +70°C; V = 5 V ± 10% or –40°C to +85°C, V = 5 V ±5%, V = 0V
amb
CC CC SS
4
4
VARIABLE CLOCK
MIN MAX
20 MHz CLOCK
SYMBOL FIGURE
PARAMETER
MIN
MAX
UNIT
MHz
ns
1/t
CLCL
29
29
29
29
29
29
29
29
29
29
29
29
Oscillator frequency
ALE pulse width
0
20
t
t
t
t
t
t
t
t
t
t
t
t
–40
10
5
LHLL
CLCL
Address valid to ALE low
Address hold after ALE low
ALE low to valid instruction in
ALE low to PSEN low
0.5t
0.5t
–20
ns
AVLL
LLAX
LLIV
CLCL
CLCL
–20
5
ns
2t
–65
35
15
ns
CLCL
0.5t
1.5t
–20
–45
5
ns
LLPL
PLPH
PLIV
PXIX
PXIZ
AVIV
PLAZ
CLCL
PSEN pulse width
30
ns
CLCL
PSEN low to valid instruction in
Input instruction hold after PSEN
Input instruction float after PSEN
Address to valid instruction in
PSEN low to address float
1.5t
–60
ns
CLCL
0
0
ns
0.5t
2.5t
–20
–80
5
ns
CLCL
45
10
ns
CLCL
10
ns
Data Memory
t
t
t
t
t
t
t
t
t
t
t
t
t
t
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
31
RD pulse width
3t
3t
–100
–100
50
50
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
RLRH
WLWH
RLDV
RHDX
RHDZ
LLDV
CLCL
WR pulse width
CLCL
RD low to valid data in
Data hold after RD
Data float after RD
ALE low to valid data in
Address to valid data in
ALE low to RD or WR low
2.5t
–90
35
CLCL
0
0
t
–20
5
CLCL
4t
CLCL
–150
–165
50
4.5t
60
AVDV
LLWL
CLCL
1.5t
–50 1.5t
+50
25
25
0
125
CLCL
CLCL
Address valid to WR low or RD low
Data valid to WR transition
Data hold after WR
2t
–75
AVWL
QVWX
WHQX
QVWH
RLAZ
WHLH
CLCL
0.5t
–25
–20
CLCL
CLCL
0.5t
5
Data valid to WR high
3.5t
–130
CLCL
45
30, 31
30, 31
RD low to address float
RD or WR high to ALE high
0
0
0.5t
–20 0.5t
+20
5
45
CLCL
CLCL
External Clock
t
t
t
t
33
33
33
33
High time
Low time
Rise time
Fall time
20
20
t
–t
ns
ns
ns
ns
CHCX
CLCX
CLCH
CHCL
CLCL CLCX
t
–t
CLCL CHCX
5
5
Shift Register
t
t
t
t
t
32
32
32
32
32
Serial port clock cycle time
6t
300
117
20
ns
ns
ns
ns
ns
XLXL
CLCL
Output data setup to clock rising edge
Output data hold after clock rising edge
Input data hold after clock rising edge
Clock rising edge to input data valid
5t
–133
CLCL
QVXH
XHQX
XHDX
XHDV
t
–30
CLCL
0
0
5t
CLCL
–133
117
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100 pF, load capacitance for all other outputs = 80 pF.
3. Interfacing the microcontroller to devices with float times up to 45 ns is permitted. This limited bus contention will not cause damage to
Port 0 drivers.
4. Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.
33
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
AC ELECTRICAL CHARACTERISTICS (12 CLOCK MODE)
1, 2, 3
T
= 0°C to +70°C; VCC = 5 V ± 10% or –40°C to +85°C, V = 5 V ±5%, V = 0 V
amb
CC SS
4
4
VARIABLE CLOCK
33 MHz CLOCK
SYMBOL FIGURE
PARAMETER
MIN
MAX
MIN
MAX
UNIT
MHz
ns
1/t
CLCL
29
29
29
29
29
29
29
29
29
29
29
29
Oscillator frequency
ALE pulse width
0
33
t
t
t
t
t
t
t
t
t
t
t
2t
–40
21
5
LHLL
CLCL
Address valid to ALE low
Address hold after ALE low
ALE low to valid instruction in
ALE low to PSEN low
t
t
–25
ns
AVLL
LLAX
LLIV
CLCL
CLCL
–25
5
ns
4t
3t
–65
–60
55
30
ns
CLCL
t
–25
5
ns
LLPL
PLPH
PLIV
PXIX
PXIZ
AVIV
PLAZ
CLCL
PSEN pulse width
3t
–45
45
ns
CLCL
PSEN low to valid instruction in
Input instruction hold after PSEN
Input instruction float after PSEN
Address to valid instruction in
PSEN low to address float
ns
CLCL
0
0
ns
t
–25
5
ns
CLCL
5t
–80
70
10
ns
CLCL
10
ns
Data Memory
t
t
t
t
t
t
t
t
t
t
t
t
t
t
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
30, 31
31
RD pulse width
6t
–100
–100
82
82
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
RLRH
WLWH
RLDV
RHDX
RHDZ
LLDV
CLCL
WR pulse width
6t
CLCL
RD low to valid data in
Data hold after RD
5t
2t
–90
–28
60
CLCL
0
0
Data float after RD
32
90
CLCL
ALE low to valid data in
Address to valid data in
ALE low to RD or WR low
Address valid to WR low or RD low
Data valid to WR transition
Data hold after WR
8t
–150
–165
CLCL
CLCL
9t
105
140
AVDV
LLWL
3t
–50
–75
3t
CLCL
+50
40
45
0
CLCL
4t
AVWL
QVWX
WHQX
QVWH
RLAZ
WHLH
CLCL
t
–30
–25
CLCL
CLCL
t
5
Data valid to WR high
RD low to address float
RD or WR high to ALE high
7t
–130
80
CLCL
30, 31
30, 31
0
0
t
–25
t
+25
5
55
CLCL
CLCL
External Clock
t
t
t
t
33
33
33
33
High time
Low time
Rise time
Fall time
17
17
t
–t
ns
ns
ns
ns
CHCX
CLCX
CLCH
CHCL
CLCL CLCX
t
–t
CLCL CHCX
5
5
Shift Register
t
t
t
t
t
32
32
32
32
32
Serial port clock cycle time
12t
360
167
50
ns
ns
ns
ns
ns
XLXL
CLCL
Output data setup to clock rising edge
Output data hold after clock rising edge
Input data hold after clock rising edge
Clock rising edge to input data valid
10t –133
CLCL
QVXH
XHQX
XHDX
XHDV
2t
CLCL
–80
0
0
10t
–133
167
CLCL
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100 pF, load capacitance for all other outputs = 80 pF.
3. Interfacing the microcontroller to devices with float times up to 45 ns is permitted. This limited bus contention will not cause damage to
Port 0 drivers.
4. Parts are tested to 3.5 MHz, but guaranteed to operate down to 0 Hz.
34
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
EXPLANATION OF THE AC SYMBOLS
Each timing symbol has five characters. The first character is always
P – PSEN
‘t’ (= time). The other characters, depending on their positions,
indicate the name of a signal or the logical status of that signal. The
designations are:
Q – Output data
R – RD signal
t – Time
A – Address
V – Valid
C – Clock
W– WR signal
D – Input data
X – No longer a valid logic level
Z – Float
H – Logic level high
I – Instruction (program memory contents)
L – Logic level low, or ALE
Examples: t
= Time for address valid to ALE low.
= Time for ALE low to PSEN low.
AVLL
LLPL
t
t
LHLL
ALE
t
t
LLPL
AVLL
t
PLPH
t
LLIV
t
PLIV
PSEN
t
LLAX
t
PXIZ
t
PLAZ
t
PXIX
A0–A7
INSTR IN
A0–A7
PORT 0
PORT 2
t
AVIV
A0–A15
A8–A15
SU00006
Figure 29. External Program Memory Read Cycle
ALE
PSEN
RD
t
WHLH
t
LLDV
t
t
LLWL
RLRH
t
RHDZ
t
LLAX
t
t
RLDV
AVLL
t
RLAZ
t
RHDX
A0–A7
FROM RI OR DPL
PORT 0
PORT 2
DATA IN
A0–A7 FROM PCL
INSTR IN
t
AVWL
t
AVDV
P2.0–P2.7 OR A8–A15 FROM DPF
A0–A15 FROM PCH
SU00025
Figure 30. External Data Memory Read Cycle
35
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
ALE
t
WHLH
PSEN
t
t
WLWH
LLWL
WR
t
LLAX
t
t
WHQX
t
AVLL
QVWX
t
QVWH
A0–A7
FROM RI OR DPL
PORT 0
PORT 2
DATA OUT
A0–A7 FROM PCL
INSTR IN
t
AVWL
P2.0–P2.7 OR A8–A15 FROM DPF
A0–A15 FROM PCH
SU00026
Figure 31. External Data Memory Write Cycle
INSTRUCTION
ALE
0
1
2
3
4
5
6
7
8
t
XLXL
CLOCK
t
XHQX
t
QVXH
OUTPUT DATA
0
1
2
3
4
5
6
7
WRITE TO SBUF
t
XHDX
t
SET TI
VALID
XHDV
INPUT DATA
CLEAR RI
VALID
VALID
VALID
VALID
VALID
VALID
VALID
SET RI
SU00027
Figure 32. Shift Register Mode Timing
V
–0.5
CC
0.7V
CC
CC
0.45V
0.2V
–0.1
t
CHCX
t
t
t
CHCL
CLCX
CLCH
t
CLCL
SU00009
Figure 33. External Clock Drive
36
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
V
–0.5
CC
V
V
+0.1V
LOAD
V
V
–0.1V
TIMING
REFERENCE
POINTS
OH
0.2V
0.2V
+0.9
–0.1
CC
V
LOAD
CC
–0.1V
LOAD
+0.1V
OL
0.45V
NOTE:
NOTE:
For timing purposes, a port is no longer floating when a 100mV change from
load voltage occurs, and begins to float when a 100mV change from the loaded
AC inputs during testing are driven at V –0.5 for a logic ‘1’ and 0.45V for a logic ‘0’.
Timing measurements are made at V min for a logic ‘1’ and V max for a logic ‘0’.
CC
IH
IL
V
/V level occurs. I /I ≥ ±20mA.
OH OL
OH OL
SU00717
SU00718
Figure 34. AC Testing Input/Output
Figure 35. Float Waveform
70
60
50
89C51Rx2Hxx
MAXIMUM ACTIVE I
CC
40
TYPICAL ACTIVE I
CC
I
(mA)
CC
30
20
MAXIMUM IDLE
10
TYPICAL IDLE
2
4
6
8
10
12
14
16
18
20
Frequency at XTAL1 (MHz, 6 clock mode)
SU01662
Figure 36. I vs. FREQ
CC
Valid only within frequency specifications of the device under test
37
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
V
–0.5
CC
0.2V
0.2V
+0.9
–0.1
CC
CC
0.45V
NOTE:
AC inputs during testing are driven at V –0.5 for a logic ‘1’ and 0.45V for a logic ‘0’.
CC
Timing measurements are made at V min for a logic ‘1’ and V max for a logic ‘0’.
IH
IL
SU00010
Figure 37. AC Testing Input/Output
V
V
+0.1V
LOAD
V
V
–0.1V
TIMING
REFERENCE
POINTS
OH
V
LOAD
–0.1V
LOAD
+0.1V
OL
NOTE:
For timing purposes, a port is no longer floating when a 100mV change from load voltage occurs,
and begins to float when a 100mV change from the loaded V /V level occurs. I /I ≥ ±20mA.
OH OL
OH OL
SU00011
Figure 38. Float Waveform
38
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
V
V
–0.5
CC
CC
CC
0.5V
I
CC
t
CHCX
t
t
t
CHCL
CLCX
CLCH
V
CC
P0
V
V
CC
t
CLCL
89C51RB2Hxx
89C51RC2Hxx
89C51RD2Hxx
RST
SU01297
EA
Figure 41. Clock Signal Waveform for I Tests in Active
(NC)
XTAL2
CC
and Idle Modes.
CLOCK SIGNAL
XTAL1
t
= t
= 10 ns
CHCL
CLCL
V
SS
V
CC
CC
SU01294
I
CC
Figure 39. I Test Condition, Active Mode.
CC
V
CC
P0
All other pins are disconnected
RST
EA
V
89C51RB2Hxx
89C51RC2Hxx
89C51RD2Hxx
V
CC
CC
I
CC
(NC)
XTAL2
XTAL1
V
CC
P0
RST
EA
V
V
SS
89C51RB2Hxx
89C51RC2Hxx
89C51RD2Hxx
SU01296
(NC)
XTAL2
XTAL1
Figure 42. I Test Condition, Power Down Mode.
CC
CLOCK SIGNAL
All other pins are disconnected; V = 2V to 5.5V
CC
V
SS
SU01295
Figure 40. I Test Condition, Idle Mode.
CC
All other pins are disconnected
39
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
FLASH EPROM MEMORY
CAPABILITIES OF THE PHILIPS 89C51Rx2Hxx
FLASH-BASED MICROCONTROLLERS
GENERAL DESCRIPTION
Flash organization
The P89C51RB2/RC2/RD2Hxx Flash memory augments EPROM
functionality with in-circuit electrical erasure and programming. The
Flash can be read and written as bytes. The Chip Erase operation will
erase the entire program memory. The Block Erase function can
erase any Flash block. In-system programming and standard parallel
programming are both available. On-chip erase and write timing
generation contribute to a user friendly programming interface.
The P89C51RB2/RC2/RD2Hxx contains 16KB/32KB/64KB of Flash
program memory. This memory is organized as 5 separate blocks.
The first two blocks are 8 kbytes in size, filling the program memory
space from address 0 through 3FFF hex. The final three blocks are
16 kbytes in size and occupy addresses from 4000 through FFFF
hex.
Figure 43 depicts the Flash memory configurations.
The P89C51RB2/RC2/RD2Hxx Flash reliably stores memory
contents even after 10,000 erase and program cycles. The cell is
designed to optimize the erase and programming mechanisms. In
addition, the combination of advanced tunnel oxide processing and
low internal electric fields for erase and programming operations
produces reliable cycling. The P89C51RB2/RC2/RD2Hxx uses a
Flash Programming and Erasure
There are three methods of erasing or programming of the Flash
memory that may be used. First, the Flash may be programmed or
erased in the end-user application by calling low-level routines
through a common entry point in the Boot ROM. The end-user
application, though, must be executing code from a different block
than the block that is being erased or programmed. Second, the
on-chip ISP boot loader may be invoked. This ISP boot loader will, in
turn, call low-level routines through the same common entry point in
the Boot ROM that can be used by the end-user application. Third,
the Flash may be programmed or erased using the parallel method
by using a commercially available EPROM programmer. The parallel
programming method used by these devices is similar to that used
by EPROM 87C51, but it is not identical, and the commercially
available programmer will need to have support for these devices.
+5 V V supply to perform the Program/Erase algorithms.
PP
FEATURES – IN-SYSTEM PROGRAMMING (ISP)
AND IN-APPLICATION PROGRAMMING (IAP)
• Flash EPROM internal program memory with Block Erase.
• Internal 1-kbyte fixed boot ROM, containing low-level in-system
programming routines and a default serial loader. User program
can call these routines to perform In-Application Programming
(IAP). The Boot ROM can be turned off to provide access to the
full 64-kbyte Flash memory.
Boot ROM
When the microcontroller programs its own Flash memory, all of the
low level details are handled by code that is permanently contained
in a 1-kbyte Boot ROM that is separate from the Flash memory.
A user program simply calls the common entry point with appropriate
parameters in the Boot ROM to accomplish the desired operation.
Boot ROM operations include things like: erase block, program byte,
verify byte, program security lock bit, etc. The Boot ROM overlays
the program memory space at the top of the address space from
FC00 to FFFF hex, when it is enabled. The Boot ROM may be
turned off so that the upper 1 kbyte of Flash program memory are
accessible for execution.
• Boot vector allows user provided Flash loader code to reside
anywhere in the Flash memory space. This configuration provides
flexibility to the user.
• Default loader in Boot ROM allows programming via the serial port
without the need for a user provided loader.
• Up to 64 kbytes external program memory if the internal program
memory is disabled (EA = 0).
• Programming and erase voltage +5 V (+12 V tolerant).
• Read/Programming/Erase using ISP/IAP:
– Byte Programming (20 ms).
– Typical quick erase times:
Block Erase (8 kbytes or 16 kbytes) in 10 seconds.
Full Erase (64 kbytes) in 20 seconds.
• Parallel programming with 87C51 compatible hardware interface
to programmer.
• In-system programming.
• Programmable security for the code in the Flash.
• 10,000 minimum erase/program cycles for each byte.
• 10-year minimum data retention.
40
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
FFFF
FFFF
BOOT ROM
FC00
(1 kB)
BLOCK 4
16 kB
89C51RD2Hxx
C000
BLOCK 3
16 kB
PROGRAM
ADDRESS
8000
BLOCK 2
16 kB
89C51RC2Hxx
4000
BLOCK 1
8 kB
2000
89C51RB2Hxx
BLOCK 0
8 kB
0000
SU01298
Figure 43. Flash Memory Configurations
connected) at the falling edge of RESET. This is the same effect as
having a non-zero status byte. This allows an application to be built
that will normally execute the end user’s code but can be manually
forced into ISP operation.
Power-On Reset Code Execution
The P89C51RB2/RC2/RD2Hxx contains two special Flash registers:
the BOOT VECTOR and the STATUS BYTE. At the falling edge of
reset, the P89C51RB2/RC2/RD2Hxx examines the contents of the
Status Byte. If the Status Byte is set to zero, power-up execution
starts at location 0000H, which is the normal start address of the
user’s application code. When the Status Byte is set to a value other
than zero, the contents of the Boot Vector is used as the high byte of
the execution address and the low byte is set to 00H. The factory
default setting is 0FCH, corresponds to the address 0FC00H for the
factory masked-ROM ISP boot loader. A custom boot loader can be
written with the Boot Vector set to the custom boot loader.
If the factory default setting for the Boot Vector (0FCH) is changed, it
will no longer point to the ISP masked-ROM boot loader code. If this
happens, the only way it is possible to change the contents of the
Boot Vector is through the parallel programming method, provided
that the end user application does not contain a customized loader
that provides for erasing and reprogramming of the Boot Vector and
Status Byte.
After programming the Flash, the status byte should be programmed
to zero in order to allow execution of the user’s application code
beginning at address 0000H.
NOTE: When erasing the Status Byte or Boot Vector, both
bytes are erased at the same time. It is necessary to reprogram
the Boot Vector after erasing and updating the Status Byte.
Hardware Activation of the Boot Loader
The boot loader can also be executed by holding PSEN LOW, P2.7,
P2.6 high, EA greater than V (such as +5 V), and ALE HIGH (or not
IH
41
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
V
CC
V
+5 V (+12 V tolerant)
PP
RST
V
+5 V
TxD
RxD
CC
TxD
RxD
XTAL2
V
89C51RB2Hxx
SS
89C51RC2Hxx
89C51RD2Hxx
XTAL1
P2.7
P2.6
“1”
“1”
V
SS
SU01299
Figure 44. In-System Programming with a Minimum of Pins
the first byte in the record. If there are zero bytes in the record, this
In-System Programming (ISP)
field is often set to 0000. The “RR” string indicates the record type.
A record type of “00” is a data record. A record type of “01” indicates
the end-of-file mark. In this application, additional record types will
be added to indicate either commands or data for the ISP facility.
The maximum number of data bytes in a record is limited to 16
(decimal). ISP commands are summarized in Table 7.
The In-System Programming (ISP) is performed without removing
the microcontroller from the system. The In-System Programming
(ISP) facility consists of a series of internal hardware resources
coupled with internal firmware to facilitate remote programming of
the P89C51RB2/RC2/RD2Hxx through the serial port. This firmware
is provided by Philips and embedded within each
P89C51RB2/RC2/RD2Hxx device.
As a record is received by the P89C51RB2/RC2/RD2Hxx, the
information in the record is stored internally and a checksum
calculation is performed. The operation indicated by the record type
is not performed until the entire record has been received. Should
an error occur in the checksum, the P89C51RB2/RC2/RD2Hxx will
send an “X” out the serial port indicating a checksum error. If the
checksum calculation is found to match the checksum in the record,
then the command will be executed. In most cases, successful
reception of the record will be indicated by transmitting a “.”
character out the serial port (displaying the contents of the internal
program memory is an exception).
The Philips In-System Programming (ISP) facility has made in-circuit
programming in an embedded application possible with a minimum
of additional expense in components and circuit board area.
The ISP function uses five pins: TxD, RxD, V , V , and V (see
Figure 44). Only a small connector needs to be available to interface
your application to an external circuit in order to use this feature.
SS
CC
PP
The V supply should be adequately decoupled and V not
PP
PP
allowed to exceed datasheet limits.
Using the In-System Programming (ISP)
In the case of a Data Record (record type 00), an additional check is
made. A “.” character will NOT be sent unless the record checksum
matched the calculated checksum and all of the bytes in the record
were successfully programmed. For a data record, an “X” indicates
that the checksum failed to match, and an “R” character indicates
that one of the bytes did not properly program. It is necessary to
send a type 02 record (specify oscillator frequency) to the
The ISP feature allows for a wide range of baud rates to be used in
your application, independent of the oscillator frequency. It is also
adaptable to a wide range of oscillator frequencies. This is
accomplished by measuring the bit-time of a single bit in a received
character. This information is then used to program the baud rate in
terms of timer counts based on the oscillator frequency. The ISP
feature requires that an initial character (an uppercase U) be sent to
the P89C51RB2/RC2/RD2Hxx to establish the baud rate. The ISP
firmware provides auto-echo of received characters.
P89C51RB2/RC2/RD2Hxx before programming data.
The ISP facility was designed to that specific crystal frequencies
were not required in order to generate baud rates or time the
programming pulses. The user thus needs to provide the
P89C51RB2/RC2/RD2Hxx with information required to generate the
proper timing. Record type 02 is provided for this purpose.
Once baud rate initialization has been performed, the ISP firmware
will only accept Intel Hex-type records. Intel Hex records consist of
ASCII characters used to represent hexadecimal values and are
summarized below:
WinISP, a software utility to implement ISP programming with a PC,
is available on Philips Semiconductors’ website. In addition, at the
website is a listing of third party commercially available serial and
parallel programmers.
:NNAAAARRDD..DDCC<crlf>
In the Intel Hex record, the “NN” represents the number of data
bytes in the record. The P89C51RB2/RC2/RD2Hxx will accept up to
16 (10H) data bytes. The “AAAA” string represents the address of
42
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
Table 7. Intel-Hex Records Used by In-System Programming
RECORD TYPE
COMMAND/DATA FUNCTION
00
Program Data
:nnaaaa00dd....ddcc
Where:
Nn
Aaaa
= number of bytes (hex) in record
= memory address of first byte in record
dd....dd = data bytes
cc
= checksum
Example:
:10008000AF5F67F0602703E0322CFA92007780C3FD
01
02
End of File (EOF), no operation
:xxxxxx01cc
Where:
xxxxxx
cc
= required field, but value is a “don’t care”
= checksum
Example:
:00000001FF
Specify Oscillator Frequency
:01xxxx02ddcc
Where:
xxxx
dd
cc
= required field, but value is a “don’t care”
= integer oscillator frequency rounded down to nearest MHz
= checksum
Example:
:0100000210ED
(dd = 10h = 16, used for 16.0–16.9 MHz)
43
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
RECORD TYPE
COMMAND/DATA FUNCTION
03
Miscellaneous Write Functions
:nnxxxx03ffssddcc
Where:
nn
xxxx
03
ff
ss
dd
cc
= number of bytes (hex) in record
= required field, but value is a “don’t care”
= Write Function
= subfunction code
= selection code
= data input (as needed)
= checksum
Subfunction Code = 01 (Erase Blocks)
ff = 01
ss = block code as shown below:
block 0, 0k to 8k, 00H
block 1, 8k to 16k, 20H
block 2, 16k to 32k, 40H
block 3, 32k to 48k, 80H
block 4, 48k to 64k, C0H
Example:
:0200000301C03A erase block 4
Subfunction Code = 04 (Erase Boot Vector and Status Byte)
ff = 04
ss = don’t care
Example:
:020000030400F7 erase boot vector and status byte
Subfunction Code = 05 (Program Security Bits)
ff = 05
ss = 00 program security bit 1 (inhibit writing to Flash)
01 program security bit 2 (inhibit Flash verify)
02 program security bit 3 (disable external memory)
Example:
:020000030501F5 program security bit 2
Subfunction Code = 06 (Program Status Byte or Boot Vector)
ff = 06
ss = 00 program status byte
01 program boot vector
Example:
:030000030601FCF7 program boot vector with 0FCH
Subfunction Code = 07 (Full Chip Erase)
Erases all blocks, security bits, and sets status and boot vector to default values
ff = 07
ss = don’t care
dd = don’t care
Example:
:0100000307F5 full chip erase
04
Display Device Data or Blank Check – Record type 04 causes the contents of the entire Flash array to be sent out
the serial port in a formatted display. This display consists of an address and the contents of 16 bytes starting with that
address. No display of the device contents will occur if security bit 2 has been programmed. Data to the serial port is
initiated by the reception of any character and terminated by the reception of any character.
General Format of Function 04
:05xxxx04sssseeeeffcc
Where:
05
xxxx
04
ssss
eeee
ff
= number of bytes (hex) in record
= required field, but value is a “don’t care”
= “Display Device Data or Blank Check” function code
= starting address
= ending address
= subfunction
00 = display data
01 = blank check
= checksum
cc
Example:
:0500000440004FFF0069 display 4000–4FFF
44
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
RECORD TYPE
COMMAND/DATA FUNCTION
05
Miscellaneous Read Functions
General Format of Function 05
:02xxxx05ffsscc
Where:
02
xxxx
05
=
=
=
=
number of bytes (hex) in record
required field, but value is a “don’t care”
“Miscellaneous Read” function code
ffss
subfunction and selection code
0000 = read signature byte – manufacturer id (15H)
0001 = read signature byte – device id # 1
0002 = read signature byte – device id # 2
(C2H)
0700 = read security bits
0701 = read status byte
0702 = read boot vector
cc
= checksum
Example:
:020000050001F8 read signature byte – device id # 1
06
Direct Load of Baud Rate
General Format of Function 06
:02xxxx06hhllcc
Where:
02
xxxx
06
hh
ll
=
=
=
=
=
=
number of bytes (hex) in record
required field, but value is a “don’t care”
”Direct Load of Baud Rate” function code
high byte of Timer 2
low byte of Timer 2
checksum
cc
Example:
:02000006F500F3
45
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
Using the Watchdog Timer (WDT)
In Application Programming Method
The 89C51Rx2 devices support the use of the WDT in IAP. The user
specifies that the WDT is to be fed by setting the most significant bit
of the function parameter passed in R1 prior to calling PGM_MTP.
The WDT function is only supported for Block Erase when using
Quick Block Erase. The Quick Block Erase is specified by
performing a Block Erase with register R0 = 0. Requesting a WDT
feed during IAP should only be performed in applications that use
the WDT since the process of feeding the WDT will start the WDT if
the WDT was not running.
Several In Application Programming (IAP) calls are available for use by
an application program to permit selective erasing and programming of
Flash sectors. All calls are made through a common interface,
PGM_MTP. The programming functions are selected by setting up
the microcontroller’s registers before making a call to PGM_MTP at
FFF0H. The oscillator frequency is an integer number rounded down
to the nearest megahertz. For example, set R0 to 11 for 11.0592 MHz.
Results are returned in the registers. The IAP calls are shown in
Table 8.
Table 8. IAP calls
IAP CALL
PARAMETER
PROGRAM DATA BYTE
Input Parameters:
R0 = osc freq (integer)
R1 = 02h
R1 = 82h (WDT feed)
DPTR = address of byte to program
ACC = byte to program
Return Parameter
ACC = 00 if pass, !00 if fail
ERASE BLOCK
Input Parameters:
R0 = osc freq (integer)
R0 = 0 (Quick Erase)
R1 = 01h
R1 = 81h (WDT feed)
DPH = block code as shown below:
block 0, 0k to 8k, 00H
block 1, 8k to 16k, 20H
block 2, 16k to 32k, 40H
block 3, 32k to 48k, 80H
block 4, 48k to 64k, C0H
DPL = 00h
Return Parameter
none
ERASE BOOT VECTOR
Input Parameters:
R0 = osc freq (integer)
R1 = 04h
R1 = 84h (WDT feed)
DPH = 00h
DPL = don’t care
Return Parameter
none
PROGRAM SECURITY BIT
Input Parameters:
R0 = osc freq (integer)
R1 = 05h
R1 = 85h (WDT feed)
DPH = 00h
DPL = 00h – security bit # 1 (inhibit writing to Flash)
01h – security bit # 2 (inhibit Flash verify)
02h – security bit # 3 (disable external memory)
Return Parameter
none
PROGRAM STATUS BYTE
Input Parameters:
R0 = osc freq (integer)
R1 = 06h
R1 = 86h (WDT feed)
DPH = 00h
DPL = 00h – program status byte
ACC = status byte
Return Parameter
ACC = status byte
46
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
IAP CALL
PARAMETER
PROGRAM BOOT VECTOR
Input Parameters:
R0 = osc freq (integer)
R1 = 06h
R1 = 86h (WDT feed)
DPH = 00h
DPL = 01h – program boot vector
ACC = boot vector
Return Parameter
ACC = boot vector
READ DEVICE DATA
Input Parameters:
R1 = 03h
R1 = 83h (WDT feed)
DPTR = address of byte to read
Return Parameter
ACC = value of byte read
READ MANUFACTURER ID
Input Parameters:
R0 = osc freq (integer)
R1 = 00h
R1 = 80h (WDT feed)
DPH = 00h
DPL = 00h (manufacturer ID)
Return Parameter
ACC = value of byte read
READ DEVICE ID # 1
READ DEVICE ID # 2
READ SECURITY BITS
READ STATUS BYTE
READ BOOT VECTOR
Input Parameters:
R0 = osc freq (integer)
R1 = 00h
R1 = 80h (WDT feed)
DPH = 00h
DPL = 01h (device ID # 1)
Return Parameter
ACC = value of byte read
Input Parameters:
R0 = osc freq (integer)
R1 = 00h
R1 = 80h (WDT feed)
DPH = 00h
DPL = 02h (device ID # 2)
Return Parameter
ACC = value of byte read
Input Parameters:
R0 = osc freq (integer)
R1 = 07h
R1 = 87h (WDT feed)
DPH = 00h
DPL = 00h (security bits)
Return Parameter
ACC = value of byte read
Input Parameters:
R0 = osc freq (integer)
R1 = 07h
R1 = 87h (WDT feed)
DPH = 00h
DPL = 01h (status byte)
Return Parameter
ACC = value of byte read
Input Parameters:
R0 = osc freq (integer)
R1 = 07h
R1 = 87h (WDT feed)
DPH = 00h
DPL = 02h (boot vector)
Return Parameter
ACC = value of byte read
47
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
Security
The security feature protects against software piracy and prevents the contents of the Flash from being read. The Security Lock bits are located
in Flash. The P89C51RB2/RC2/RD2Hxx has three programmable security lock bits that will provide different levels of protection for the on-chip
code and data (see Table 9).
Table 9.
1
SECURITY LOCK BITS
PROTECTION DESCRIPTION
LEVEL
LB1
LB2
LB3
1
0
0
0
MOVC instructions executed from external program memory are disabled from fetching code
bytes from internal memory.
2
3
1
1
1
0
1
1
0
0
1
Block erase is disabled. Erase or programming of the status byte or boot vector is disabled.
Verify of code memory is disabled.
4
External execution is disabled.
NOTES:
1. Security bits are independent of each other. Full-chip erase may be performed regardless of the state of the security bits.
2. Any other combination of lock bits is undefined.
3. Setting LBx doesn’t prevent programming of unprogrammed bits.
48
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
DIP40: plastic dual in-line package; 40 leads (600 mil)
SOT129-1
49
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
PLCC44: plastic leaded chip carrier; 44 leads
SOT187-2
50
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
LQFP44: plastic low profile quad flat package; 44 leads; body 10 x 10 x 1.4 mm
SOT389-1
51
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
REVISION HISTORY
Date
CPCN
Description
2002 May 24
9397 750 09594
– “Hxx” added to the device type throughout the document
– Corrected SFR addresses in PCA chapter (Figures 21–25)
– P2.6 must be high to activate the Boot Loader by hardware (page 41)
– Deleted North America-specific part numbers
2001 Jun 27
9397 750 08525
Previous release
52
2002 May 24
Philips Semiconductors
Product data
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RB2/P89C51RC2/
P89C51RD2Hxx
Data sheet status
Product
status
Definitions
[1]
Data sheet status
[2]
Objective data
Development
This data sheet contains data from the objective specification for product development.
Philips Semiconductors reserves the right to change the specification in any manner without notice.
Preliminary data
Product data
Qualification
Production
This data sheet contains data from the preliminary specification. Supplementary data will be
published at a later date. Philips Semiconductors reserves the right to change the specification
without notice, in order to improve the design and supply the best possible product.
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply.
Changes will be communicated according to the Customer Product/Process Change Notification
(CPCN) procedure SNW-SQ-650A.
[1] Please consult the most recently issued data sheet before initiating or completing a design.
[2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL
http://www.semiconductors.philips.com.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Righttomakechanges—PhilipsSemiconductorsreservestherighttomakechanges, withoutnotice, intheproducts, includingcircuits,standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Koninklijke Philips Electronics N.V. 2002
Contact information
All rights reserved. Printed in U.S.A.
For additional information please visit
http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
Date of release: 05-02
9397 750 09594
For sales offices addresses send e-mail to:
sales.addresses@www.semiconductors.philips.com.
Document order number:
Philips
Semiconductors
相关型号:
P89C51RB2BA
80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
NXP
P89C51RB2BB
80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
NXP
P89C51RB2BBD
IC 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP44, 10 X 10 X 1.40 MM, PLASTIC, LQFP-44, Microcontroller
NXP
P89C51RB2BP
80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
NXP
P89C51RB2FA
80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
NXP
P89C51RB2FB
80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
NXP
©2020 ICPDF网 联系我们和版权申明