PCD3311CT-T [NXP]
暂无描述;INTEGRATED CIRCUITS
DATA SHEET
PCD3311C; PCD3312C
DTMF/modem/musical-tone
generators
1996 Nov 21
Product specification
Supersedes data of May 1990
File under Integrated Circuits, IC03
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
CONTENTS
15
16
17
DEFINITIONS
LIFE SUPPORT APPLICATIONS
PURCHASE OF PHILIPS I2C COMPONENTS
1
2
3
4
5
6
FEATURES
GENERAL DESCRIPTION
QUICK REFERENCE DATA
ORDERING INFORMATION
BLOCK DIAGRAM
PINNING INFORMATION
6.1
6.2
6.3
6.4
6.5
6.6
Pinning PCD3311CP
Pin description PCD3311CP
Pinning PCD3311CT
Pin description PCD3311CT
Pinning PCD3312C
Pin description PCD3312C
7
FUNCTIONAL DESCRIPTION
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
General
Clock/oscillator connection
Mode selection (PCD3311C)
Data inputs (PCD3311C)
Strobe input (PCD3311C )
I2C-bus clock and data inputs
Address input
I2C-bus data configuration
Tone output
Power-on reset
Tables of Input and output
8
I2C-BUS INTERFACE
8.1
Bit transfer
8.2
8.3
8.4
Start and stop conditions
System configuration
Acknowledge
8.5
8.5.1
8.5.2
Timing specifications
Standard mode
Low-speed mode
9
HANDLING
10
11
12
13
14
LIMITING VALUES
CHARACTERISTICS
APPLICATION INFORMATION
PACKAGE OUTLINES
SOLDERING
14.1
Introduction
14.2
DIP
14.2.1
14.2.2
14.3
Soldering by dipping or by wave
Repairing soldered joints
SO
14.3.1
14.3.2
14.3.3
Reflow soldering
Wave soldering
Repairing soldered joints
1996 Nov 21
2
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
used, and a separate microcontroller is required to control
the devices.
1
FEATURES
• DTMF, modem and musical tone generation
• Stabilized output voltage level
Both the devices can interface to I2C-bus compatible
microcontrollers for serial input. The PCD3311C can also
interface directly to all standard microcontrollers,
accepting a binary coded parallel input.
• Low output distortion with on-chip filtering conforming to
CEPT recommendations
• Latched inputs for data bus applications
• I2C-bus compatible
• Selection of parallel or serial (I2C-bus) data input
With their on-chip voltage reference the PCD3311C and
PCD3312C provide constant output amplitudes which are
independent of the operating supply voltage and ambient
temperature.
(PCD3311C).
An on-chip filtering system assures a very low total
harmonic distortion in accordance with CEPT
recommendations.
2
GENERAL DESCRIPTION
The PCD3311C and PCD3312C are single-chip silicon
gate CMOS integrated circuits. They are intended
principally for use in telephone sets to provide the
dual-tone multi-frequency (DTMF) combinations required
for tone dialling systems. The various audio output
frequencies are generated from an on-chip 3.58 MHz
quartz crystal-controlled oscillator. A separate crystal is
In addition to the standard DTMF frequencies the devices
can also provide:
• Twelve standard frequencies used in simplex modem
applications for data rates from 300 to 1200 bits per
second
• Two octaves of musical scales in steps of semitones.
3
QUICK REFERENCE DATA
SYMBOL
VDD
IDD
Istb
PARAMETER
MIN.
2.5
TYP.
MAX.
6.0
UNIT
operating supply voltage
operating supply current
standby current
−
−
−
V
−
0.9
3
mA
µA
mV
mV
dB
dB
°C
−
VHG(RMS) DTMF HIGH group output voltage level (RMS value)
VLG(RMS) DTMF LOW group output voltage level (RMS value)
158
125
1.85
−
192
150
2.10
−25
−
205
160
2.35
−
Gv
pre-emphasis (voltage gain) of group
total harmonic distortion
THD
Tamb
operating ambient temperature
−25
+70
4
ORDERING INFORMATION
PACKAGE
TYPE NUMBER
NAME
DESCRIPTION
VERSION
PCD3311CP
PCD3311CT
PCD3312CP
PCD3312CT
DIP14
SO16
DIP8
SO8
plastic dual in-line package; 14 leads (300 mil)
SOT27-1
SOT162-1
SOT97-1
SOT176-1
plastic small outline package; 16 leads; body width 7.5 mm
plastic dual in-line package; 8 leads (300 mil)
plastic small outline package; 8 leads; body width 7.5 mm
1996 Nov 21
3
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
5
BLOCK DIAGRAM
V
V
OSCI
1(3)
OSCO
2(4)
DD
14(2)
SS
13(1)
CLOCK
GENERATOR
OSCILLATOR
3
MODE
HIGH
GROUP
DIVIDER
DAC
HIGH
4
D5
D4
12
SWITCHED
CAPACITOR
BANDGAP
VOLTAGE
11
INPUT
CONTROL
LOGIC
DIVIDER
SELECTION
(ROM)
D3
(5)6
TONE
10
D2
ADDER
9(8)
8(7)
REFERENCE
SWITCHED RESISTOR
CAPACITOR CAPACITOR
D1/SDA
D0/SCL
DAC
LOW
LOW
GROUP
DIVIDER
5
PCD3311C
PCD3312C
STROBE
7(6)
MGG543
A
0
The un-parenthesised numbers are for the PCD3311CP, those in parenthesis for the PCD3312C.
Fig.1 Block diagram.
6
PINNING INFORMATION
Pinning PCD3311CP
6.2
Pin description PCD3311CP
6.1
SYMBOL
PIN
1
TYPE
DESCRIPTION
oscillator input
OSCI
I
O
I
OSCO
MODE
2
oscillator output
3
mode select input (selects
I2C or parallel data input)
handbook, halfpage
OSCI
OSCO
MODE
D5
1
2
3
4
5
6
7
V
V
14
13
12
11
10
9
DD
SS
D5
4
5
I
I
parallel data input
STROBE
strobe input (for loading
data in parallel mode)
D4
TONE
A0
6
7
8
9
O
I
frequency output (DTMF,
modem, musical tones)
D3
PCD3311CP
D2
STROBE
TONE
A0
slave address input (to be
connected to VDD
D1/SDA
D0/SCL
or VSS
)
D0/SCL
D1/SDA
I
parallel data input or
I2C-bus clock line
8
MGG508
I
parallel data input or
I2C-bus data line
D2 − D4
VSS
10 − 12
13
I
parallel data inputs
negative supply
positive supply
P
P
Fig.2 Pin configuration PCD3311CP.
VDD
14
1996 Nov 21
4
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
6.3
Pinning PCD3311CT
6.4
Pin description PCD3311CT
SYMBOL
PIN TYPE
DESCRIPTION
oscillator input
OSCI
1
2
3
I
O
I
OSCO
MODE
oscillator output
mode select input (selects
I2C or parallel data input)
handbook, halfpage
OSCI
OSCO
MODE
D5
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
V
DD
SS
D5
4
5
6
I
−
I
parallel data input
not connected
n.c.
D4
STROBE
strobe input (for loading
data in parallel mode)
n.c.
PCD3311CT
TONE
A0
7
8
O
I
frequency output (DTMF,
modem, musical tones)
D3
n.c.
D2
STROBE
TONE
A0
slave address input (to be
connected to VDD or VSS
D1/SDA
D0/SCL
)
D0/SCL
D1/SDA
9
I
parallel data input or
I2C-bus clock line
MGG509
10
I
parallel data input or
I2C-bus data line
D2, D3
n.c.
11, 12
13
I
parallel data inputs
not connected
−
I
D4
14
parallel data input
negative supply
positive supply
VSS
15
P
P
Fig.3 Pin configuration PCD3311CT.
VDD
16
6.5
Pinning PCD3312C
6.6
Pin description PCD3312C
SYMBOL
VSS
PIN TYPE
DESCRIPTION
negative supply
1
2
3
4
5
P
P
I
VDD
positive supply
oscillator input
oscillator output
OSCI
OSCO
TONE
O
O
handbook, halfpage
V
V
1
2
3
4
8
7
6
5
SDA
SS
frequency output (DTMF,
modem, musical tones)
SCL
A0
DD
PCD3312C
A0
6
I
slave address input (to be
OSCI
connected to VDD or VSS
I2C-bus clock line
I2C-bus data line
)
TONE
OSCO
SCL
SDA
7
8
I
I
MGG510
Fig.4 Pin configuration PCD3312C.
1996 Nov 21
5
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
7
FUNCTIONAL DESCRIPTION
7.4
Data inputs (PCD3311C)
Inputs D0, D1, D2, D3, D4 and D5 are used in the parallel
data input mode of the PCD3311C. Inputs D0 and D1 are
also used in serial input mode when they act as the SCL
and SDA inputs respectively. Inputs D0 and D1 have no
internal pull-down or pull-up resistors and must not be left
open in any application. Inputs D2, D3, D4 and D5 have
internal pull-down.
7.1
General (see Fig.1)
The Input Control Logic decodes the input data to
determine whether DTMF, modem or musical tones are
selected; and which particular tone or combination of
tones is required.
A code representing the required tones is sent to the
Divider Selection ROM which selects the correct division
ratio in both of the Frequency Dividers (or in one divider, if
only a single tone is required).
D4 and D5 are used to select between DTMF dual, DTMF
single, modem and musical tones (see Table 1). D0, D1,
D2 and D3 select the tone combination or single tone
within the selected application. They also, in combination
with D4, select the standby mode. See Tables 2, 3, 4
and 5.
The Oscillator circuit provides a square wave of frequency
3.58 MHz. Each Frequency Divider divides the frequency
of the Oscillator to give a serial digital square wave with a
frequency simply related to that of the required tone.
PCD 3312C has no parallel data pins as data input is via
the I2C-bus.
The output from each Frequency Divider goes to a DAC,
which is also fed by a clock derived from the oscillator.
Using these two signals, the DAC produces an
Table 1 Use of D5 and D4 to select application
approximate sine wave of the required frequency, with an
amplitude derived from the Voltage Reference.
D5
D4
APPLICATION
LOW LOW DTMF single tones; musical tones;
standby
The output from the DAC goes to an Adder where, for
DTMF, it is combined with the output from the other DAC.
LOW HIGH DTMF dual tones (all 16 combinations)
HIGH LOW modem tones
The output from the Adder goes through two stages of Low
Pass Filters to give a smoothed tone (single or dual), and
finally to the TONE output.
HIGH HIGH musical tones
7.5
Strobe input (PCD3311C )
7.2
Clock/oscillator connection
The STROBE input (with internal pull-down) allows the
loading of parallel data into D0 to D5 when MODE is HIGH.
The timebase for the PCD3311C and PCD3312C is a
crystal-controlled oscillator, requiring a 3.58 MHz quartz
crystal to be connected between OSCI and OSCO.
Alternatively, the OSCI input can be driven from an
external clock of 3.58 MHz.
The data inputs must be stable preceding the
positive-going edge of the strobe pulse (active HIGH).
Input data are loaded at the negative-going edge of the
strobe pulse and then the corresponding tone (or standby
mode) is provided at the TONE output. The output remains
unchanged until the negative-going edge of the next
STROBE pulse (for new data) is received. Figure 5 is an
example of the timing relationship between STROBE and
the data inputs.
7.3
Mode selection (PCD3311C)
The MODE input selects the data input mode for the
PCD3311C. When MODE is connected to VDD (HIGH),
data can be received in the parallel mode. When
connected to VSS (LOW) or left open, data can be received
via the serial I2C-bus.
When MODE is LOW, data is received serially via the
I2C-bus.
PCD 3312C has no MODE input as data input is via the
I2C-bus only.
1996 Nov 21
6
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
t
SPW
t
90%
10%
STROBE
DH
t
DS
D0
D1
D2
D3
D4
D5
t
(ON)
tone
TONE
oscillator OFF
oscillator ON
no output tone
oscillator ON
output tones
MGG511
Fig.5 Timing of STROBE, parallel data inputs and TONE output (770 Hz + 1477 Hz in example) in the parallel
mode (MODE = HIGH).
7.6
I2C-bus clock and data inputs
7.8
I2C-bus data configuration (see Fig.6)
SCL and SDA are the serial clock and serial data inputs
according to the I2C-bus specification, see Chapter 8.
The PCD3311C and PCD3312C are always slave
receivers in the I2C-bus configuration. The R/W bit in is
thus always LOW, indicating that the master
(microcontroller) is writing.
SCL and SDA must be pulled up externally to VDD
.
For the PCD3311C, SCL and SDA are combined with
parallel inputs D0 and D1 respectively - D0/SCL and
D1/SDA operate serially only when MODE is LOW.
The slave address in the serial mode consists of 7 bits: 6
bits internally fixed, 1 externally set via A0. in the serial
mode, the same input data codes are used as in the
parallel mode. See Tables 2, 3, 4 and 5.
7.7
Address input
Address input A0 defines the least significant bit of the
I2C-bus address of the device (see Fig.6). The first 6 bits
of the address are fixed internally. By tying the A0 of each
device to VDD (HIGH) and VSS (LOW) respectively, two
different PCD3311C or PCD3312C devices can be
individually addressed on the bus.
7.9
Tone output
The single and dual tones provided at the TONE output are
first filtered by an on-chip switched-capacitor filter,
followed by an active RC low-pass filter. The filtered tones
fulfil the CEPT recommendations for total harmonic
distortion of DTMF tones. An on-chip reference voltage
provides output tone levels independent of the supply
voltage. Tables 3, 4 and 5 give the frequency deviation of
the output tones with respect to the standard DTMF,
modem and music frequencies.
Whether one or two devices are used, A0 must be
connected to VDD or VSS
.
1996 Nov 21
7
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
acknowledge
from slave
acknowledge
from slave
MSB
0
R/W
0
S
1
0
0
1
0
A0
A
X
X
D5 D4 D3 D2 D1 D0
A
P
slave address
data
internal STROBE
for data latching
MGG512
Fig.6 I2C-bus data format.
7.10 Power-on reset
In order to avoid an undefined state when the power is switched ON, the devices have an internal reset circuit which sets
the standby mode (oscillator OFF).
7.11 TABLES OF INPUT AND OUTPUT
The specified output tones are obtained when a 3.579545 MHz crystal is used.
In each table, the logical states for the input data lines are related to voltage levels as follows:
1 = HIGH = VDD
0 = LOW = VSS
X = don’t care
Table 2 Input data for no output tone, TONE in 3-state
D5
X
D4
0
D3
0
D2
0
D1
0
D0
0
HEX(1)
00 or 20
01 or 21
02 or 22
03 or 23
OSCILLATOR
ON
X
0
0
0
0
1
OFF
OFF
OFF
X
0
0
0
1
0
X
0
0
0
1
1
Note
1. The alternative HEX values depend on the value of D5.
1996 Nov 21
8
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
Table 3 Input data and output for DTMF tones
TONE
OUTPUT
FREQ.
STANDARD
FREQUENCY
FREQUENCY
DEVIATION
D5
D4
D3
D2
D1
D0
HEX
SYMBOL
Hz
Hz
%
Hz
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
08
09
0A
0B
0C
0D
0E
0F
10
11
−
−
−
−
−
−
−
−
0
1
2
3
4
5
6
7
8
9
A
B
C
D
*
697
697.90
+0.13 +0.90
+0.06 +0.46
−0.18 −1.55
+0.24 +2.23
−0.21 −2.55
+0.42 +5.66
+0.35 +5.21
+0.32 +5.24
770
770.46
852
850.45
941
943.23
1209
1206.45
1336
1341.66
1477
1482.21
1633
1638.24
941+1336
697+1209
697+1336
697+1477
770+1209
770+1336
770+1477
852+1209
852+1336
852+1477
697+1633
770+1633
852+1633
941+1633
941+1209
941+1477
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
#
Table 4 Input data and output for modem tones
TONE
OUTPUT
FREQ.
STANDARD
FREQUENCY
FREQUENCY
DEVIATION
TELECOM.
STANDARD
D5
D4
D3
D2
D1
D0
HEX
Hz
Hz
%
Hz
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
1
1
0
0
0
1
0
1
0
1
24
25
26
27
28
29
1300
2100
1200
2200
980
1296.94
2103.14
1197.17
2192.01
978.82
−0.24 −3.06
+0.15 +3.14
−0.24 −2.83
−0.36 −7.99
−0.12 −1.18
−0.08 −0.97
V.23
Bell 202
V.21
1180
1179.03
1996 Nov 21
9
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
TONE
OUTPUT
FREQ.
STANDARD
FREQUENCY
FREQUENCY
DEVIATION
TELECOM.
STANDARD
D5
D4
D3
D2
D1
D0
HEX
Hz
Hz
%
Hz
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
0
0
1
1
1
1
1
1
0
0
1
1
0
1
0
1
0
1
2A
2B
2C
2D
2E
2F
1070
1270
1650
1850
2 025
2225
1 073.33
1265.30
1655.66
1852.77
2021.20
2223.32
+0.31 +3.33
−0.37 −4.70
+0.34 +5.66
+0.15 +2.77
−0.19 −3.80
−0.08 −1.68
Bell 103
V.21
Bell 103
Table 5 Input/output for musical tones
STD. FREQ.
BASED ON
A4 = 440 Hz
TONE
OUTPUT
FREQUENCY
D5
D4
D3
D2
D1
D0
HEX
NOTE
Hz
Hz
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
0
0
1
1
0
0
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
0
0
0
1
1
0
0
0
0
0
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
0
1
1
0
1
0
0
0
1
1
1
0
1
0
1
0
1
0
1
0
1
0
1
1
0
1
0
0
0
1
0
1
1
1
0
1
30
31
32
33
34
35
36
37
38
39
3A
29
3B
3C
3D
0E
3E
2C
3F
04
05
25
2F
06
07
D#5
622.3
659.3
622.5
659.5
E5
F5
698.5
697.9
F#5
G5
740.0
741.1
784.0
782.1
G#5
A5
830.6
832.3
880.0
879.3
A#5
B5
932.3
931.9
987.8
985.0
C6
1046.5
1108.7
1174.7
1244.5
1318.5
1396.9
1480.0
1568.0
1661.2
1760.0
1864.7
1975.5
2093.0
2217.5
2349.3
2489.0
1044.5
1111.7
1179.0
1245.1
1318.9
1402.1
1482.2
1572.0
1655.7
1768.5
1875.1
1970.0
2103.1
2223.3
2358.1
2470.4
C#6
D6
D#6
E6
F6
F#6
G6
G#6
A6
A#6
B6
C7
C#7
D7
D#7
1996 Nov 21
10
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
8
I2C-BUS INTERFACE
The I2C-bus is for two-way communication between different ICs or modules. It uses only two lines, a serial data line
(SDA) and a serial clock line (SCL), both of which are bi-directional. Both lines must be connected to a positive supply
via a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus
is not busy.
8.1
Bit transfer (see Fig.7)
One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period
of the clock pulse as changes in the data line at this time will be interpreted as control signals.
SDA
SCL
data line
stable;
data valid
change
of data
allowed
MBC621
Fig.7 Bit transfer.
8.2
Start and stop conditions (see Fig.8)
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line, while the
clock is HIGH is defined as the start condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is
defined as the stop condition (P).
SDA
SCL
SDA
SCL
S
P
STOP condition
START condition
MBC622
Fig.8 Start and stop conditions.
1996 Nov 21
11
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
8.3
System configuration (see Fig.9)
A device generating a message is a ‘transmitter’, a device receiving a message is the ‘receiver’. The device that controls
message transfer is the ‘master’ and the devices that are controlled by the master are the ‘slaves’.
SDA
SCL
MASTER
TRANSMITTER /
RECEIVER
SLAVE
TRANSMITTER /
RECEIVER
MASTER
TRANSMITTER /
RECEIVER
SLAVE
RECEIVER
MASTER
TRANSMITTER
MBA605
Fig.9 System configuration.
8.4
Acknowledge
The number of data bytes transferred between the start and stop conditions from transmitter to receiver is not limited.
Each byte of eight bits is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the
transmitter whereas the master generates an extra acknowledge after the reception of each byte. Also a master must
generate an acknowledge after reception of each byte that has been clocked out of the slave transmitter. The device that
acknowledges has to pull down the SDA line during the acknowledge-related clock pulse. Set-up and hold times must
be taken into account to ensure that the SDA line is stable LOW during the whole HIGH period of the
acknowledge-related clock pulse. A master receiver must signal an end of data to the transmitter by not generating an
acknowledge on the last byte that has been clocked out of the slave. In this event the transmitter must leave the data
line HIGH to enable the master to generate the stop condition.
DATA OUTPUT
BY TRANSMITTER
not acknowledge
DATA OUTPUT
BY RECEIVER
acknowledge
SCL FROM
MASTER
1
2
8
9
S
clock pulse for
acknowledgement
START
CONDITION
MBC602
Fig.10 Acknowledgment on the I2C-bus.
1996 Nov 21
12
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
8.5
Timing specifications
The PCD3311C and PCD3312C accept data input from a microcontroller and are ‘slave receivers’ when operating via
the I2C-bus. They support the ‘standard’ and ‘low-speed’ modes of the I2C-bus, but not the ‘fast’ mode detailed in “The
I2C-bus and how to use it” document order no. 9398 393 40011. The timing requirements for the devices are described
in Sections 8.5.1 and 8.5.2.
8.5.1
STANDARD MODE
Masters generate a bus clock with a maximum frequency of 100 kHz. Detailed timing is shown in Fig.11, where the two
signal levels are LOW = VIL and HIGH = VIH, see Chapter 11. Figure 12 shows a complete data transfer in standard
mode. The time symbols are explained in Table 6.
SDA
t
t
f
t
BUF
LOW
SCL
SDA
t
HIGH
t
t
HD;STA
r
t
HD;DAT
t
SU;DAT
MBC764
t
SU;STA
t
SU;STO
Fig.11 Standard mode timing.
1996 Nov 21
13
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
SDA
SCL
1 - 7
8
9
1 - 7
8
9
1 - 7
8
9
ACK
START ADDRESS R/W
CONDITION
ACK
DATA
START ADDRESS R/W
CONDITION
ACK
STOP
MBC765
Clock LOW minimum = 4.7 µs; clock HIGH minimum = 4 µs.
The dashed line is the acknowledgment of the receiver.
Mark-to-space ratio = 1 : 1 (LOW-to-HIGH).
Maximum number of bytes is unrestricted.
Premature termination of transfer is allowed by generation of STOP condition.
Acknowledge clock bit must be provided by master.
Fig.12 Complete data transfer in standard mode.
Table 6 Explanation of time symbols used in Fig.11
SYMBOL
fSCL
PARAMETER
SCL clock frequency
tolerable pulse spike width
bus free time
REMARKS
MIN. MAX. UNIT
0
100
100
−
kHz
ns
tSW
−
tBUF
The time that the bus is free (SDA is HIGH)
before a new transmission is initiated by SDA
going LOW.
4.7
µs
tSU;STA
tHD;STA
set-up time repeated START
hold time START condition
Only valid for repeated start code.
4.7
−
−
µs
µs
The time between SDA going LOW and the first 4.0
valid negative-going transition of SCL.
tLOW
tHIGH
tr
SCL LOW time
The LOW period of the SCL clock.
The HIGH period of the SCL clock.
4.7
4.0
−
−
µs
µs
µs
µs
ns
ns
µs
SCL HIGH time
−
rise time SDA and SCL
fall time SDA and SCL
data set-up time
1.0
0.3
−
tf
−
tSU;DAT
tHD;DAT
tSU;STO
250
0
data hold time
−
set-up time STOP condition
4.0
−
8.5.2
LOW-SPEED MODE
Masters generate a bus clock with a maximum frequency of 2 kHz; a minimum LOW period of 105 µs and a minimum
HIGH period of 365 µs. The mark-to-space ratio is 1 : 3 LOW-to-HIGH. Detailed timing is shown in Fig.13, where the two
signal levels are LOW = VIL and HIGH = VIH, see Chapter 11. Figure 14 shows a complete data transfer in low-speed
mode.The time symbols are explained in Table 7.
1996 Nov 21
14
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
SDA
t
t
f
t
LOW
BUF
SCL
SDA
t
t
t
t
r
HIGH
HD;STA
SU;DAT
t
HD;DAT
t
SU;STA
t
SU;STO
MGG545
Fig.13 Low-speed mode timing.
SDA
R/W
SCL
START
CONDITION
START BYTE
DUMMY
ACKNOWLEDGE START
CONDITION
REPEATED
ADDRESS
ACKNOWLEDGE STOP
CONDITION
MGG546
Clock LOW minimum = 130 µs ±25 µs; clock HIGH minimum 390 µs ±25 µs.
Mark-to-space ratio = 1 : 3 (LOW-to-HIGH).
Start byte 0000 0001.
Maximum number of bytes = 6.
Premature termination of transfer not allowed.
Acknowledge clock bit must be provided by master.
Fig.14 Complete data transfer in low speed mode.
15
1996 Nov 21
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
Table 7 Explanation of time symbols used in Fig.13
SYMBOL
PARAMETER
SCL clock frequency
REMARKS
MIN. MAX. UNIT
fSCL
tSW
0
2
kHz
ns
tolerable pulse spike width
bus free time
−
100
−
tBUF
The time that the bus is free (SDA is
HIGH) before a new transmission is
initiated by SDA going LOW.
105
µs
tSU;STA
tHD;STA
set-up time repeated START
hold time START condition
Only valid for repeated start code.
105
365
155
415
µs
µs
The time between SDA going LOW and
the first valid negative-going transition of
SCL.
tLOW
tHIGH
tr
SCL LOW time
The LOW period of the SCL clock.
The HIGH period of the SCL clock.
105
365
−
155
−
µs
µs
µs
µs
ns
ns
µs
SCL HIGH time
rise time SDA and SCL
fall time SDA and SCL
data set-up time
1.0
0.3
−
tf
−
tSU;DAT
tHD;DAT
tSU;STO
250
0
data hold time
−
set-up time STOP condition
105
155
9
HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, it is good practice to take
normal precautions appropriate to handling MOS devices (see “Handbook IC03, Section: General, Handling MOS
devices”).
1996 Nov 21
16
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
10 LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
MIN.
−0.8
MAX.
+8.0
UNIT
VDD
VI
supply voltage
V
V
all input voltages
DC input current
DC output current
total power dissipation
−0.8
−10
−10
−
VDD + 0.8
+10
II
mA
mA
mW
mW
mA
mA
°C
IO
+10
Ptot
PO
IDD
ISS
Tstg
Tamb
300
power dissipation per output
supply current through pin VDD
supply current through pin VSS
storage temperature
−
50
−50
−50
−65
−25
+50
+50
+150
+70
operating ambient temperature
°C
11 CHARACTERISTICS
VDD = 2.5 to 6.0 V; VSS = 0 V; Tamb = −25 to +70 °C; all voltages with respect to VSS; fxtal = 3.58 MHz (gmL);
maximum series resistance = 50 Ω; unless otherwise specified.
SYMBOL
PARAMETER
operating supply voltage
MIN.
2.5
TYP
MAX.
6.0
UNIT
VDD
IDD
−
V
operating supply current (note 1)
no output tone
−
−
−
−
50
0.5
0.6
−
100
0.8
0.9
3
µA
single output tone
mA
mA
µA
dual output tone
Istb
static standby current (note 2)
Inputs/outputs (SDA)
D0 TO D5; MODE; STROBE
VIL
VIH
LOW level input voltage
HIGH level input voltage
0
−
−
0.3VDD
VDD
V
V
0.7VDD
D2 TO D5 MODE; STROBE; A0
IIL
pull-down input current; VI = VDD
−30
−150
−300
nA
SCL (D0); SDA (D1)
IOL
fSCL
Ci
LOW level output current (SDA); VOL = 0.4 V
3
−
−
−
−
−
−
−
−
mA
kHz
pF
SCL clock frequency
100
7
input capacitance; VI = VSS
allowable input spike pulse width
ti
100
ns
1996 Nov 21
17
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
SYMBOL
PARAMETER
MIN.
TYP
MAX.
UNIT
TONE output (see test circuit, Fig.15)
VHG(RMS)
VLG(RMS)
VDC
DTMF output voltage (RMS), HIGH group
158
192
205
mV
DTMF output voltage (RMS), LOW group
DC voltage level
125
−
150
1⁄2 VDD
160
−
mV
V
Gv
voltage gain (pre-emphasis) of group
Total Harmonic Distortion; Tamb = 25 °C
dual tone (note 3)
1.85
2.10
2.35
dB
THD
−
−
−
−25
−29
0.1
−
dB
dB
kΩ
modem tone (note 4)
−
Zo
output impedance
0.5
OSCI input
VOSC(p-p)
maximum allowable amplitude at OSCI
−
−
VDD − VSS
V
Timing (VDD = 3 V)
tOSC(ON)
tTONE(ON)
tSPW
oscillator start-up time
−
3
−
−
−
−
−
ms
ms
ns
TONE start-up time (note 5)
STROBE pulse width (note 6)
data set-up time (note 6)
data hold time (note 6)
−
0.5
−
400
150
100
tDS
−
ns
tDH
−
ns
Notes
1. Oscillator ON; VDD = 3 V; crystal connected between OSCI and OSCO; D0/SCL and D1/SDA connected via
resistance of 5.6 kΩ to VDD; all other pins left open.
2. As note 1, but with oscillator OFF.
3. Related to the level of the LOW group frequency component, according to CEPT recommendations.
4. Related to the level of the fundamental frequency.
5. Oscillator must be running.
6. Values are referenced to the 10% and 90% levels of the relevant pulse amplitudes, with a total voltage swing from
VSS to VDD.
handbook, halfpage
1 µF
V
DD
TONE
PCD3311C
PCD3312C
50 pF
10 kΩ
V
SS
MGG513
Fig.15 TONE output test circuit.
18
1996 Nov 21
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
MGG515
MGG514
300
1.6
handbook, halfpage
handbook, halfpage
T
=
amb
I
stb
I
DD
−25 ˚C
(µA)
T
=
(µA)
amb
−25 ˚C
1.2
+25 ˚C
+70 ˚C
200
+25 ˚C
+70 ˚C
0.8
0.4
0
100
0
0
2
4
6
8
2
6
8
0
4
V
(V)
DD
V
(V)
DD
Fig.17 Operating supply current as a function of
supply voltage; oscillator ON, no output at
TONE.
Fig.16 Standby supply current as a function of
supply voltage; oscillator OFF.
MGG517
MGG516
6
1.5
handbook, halfpage
handbook, halfpage
T
=
amb
T
= −25 ˚C
amb
−25 ˚C
I
I
I
DD
+25 ˚C
+70 ˚C
(µA)
(mA)
+25 ˚C
+70 ˚C
4
1
2
0
0.5
0
0
0
1
2
3
2
4
6
8
(V)
V (V)
V
I
DD
Fig.18 Operating supply current as a function of
supply voltage; oscillator ON, dual tone at
TONE.
Fig.19 Pull-down input current as a function of
input voltage; VDD = 3 V.
1996 Nov 21
19
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
MGG518
MGG519
−11
0.4
handbook, halfpage
handbook, halfpage
V
TONE
V
T
=
TONE
amb
(dBm)
(dB)
−25 ˚C
+25 ˚C
HIGH GROUP
−12
T
=
amb
0
+70 ˚C
−25 ˚C
+25 ˚C
−13
−14
−15
−0.4
−0.8
+70 ˚C
−25 ˚C
+25 ˚C
LOW GROUP
+70 ˚C
6
5
4
3
0
2
4
6
10
10
10
10
R
(Ω)
V
(V)
L
DD
Fig.20 DTMF output voltage levels as a function of
Fig.21 Dual tone output voltage level as a function
of output load resistance.
operating supply voltage; RL = 1 MΩ.
MGG520
0
level
(dBm)
−20
CS203
−40
−60
−80
−100
0
1
2
3
4
5
frequency (kHz)
MGG521
0
level
(dBm)
−20
−40
−60
−80
CS203
−100
0
10
20
30
40
50
frequency (kHz)
Fig.22 Typical frequency spectrum of a dual tone signal after flat-band amplification of 6 dB.
20
1996 Nov 21
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
12 APPLICATION INFORMATION
V
V
DD
handbook, halfpage
SS
mute
1
4
7
2
5
8
0
3
6
9
A
B
C
D
GENERAL
PURPOSE
MICROCONTROLLER
(4 or 8-BIT)
data bus
OSCI OSCO STROBE
D0
PCD3311C
TONE
D5
MODE
V
V
SS
DD
MBH669
Fig.23 PCD3311C driven by microcontroller with parallel data bus.
V
V
DD
handbook, halfpage
SS
mute
1
4
7
2
5
8
0
3
6
9
A
B
C
D
TELEPHONY
MICROCONTROLLER
PCF84C21A
OSCI OSCO
3.58 MHz
2
4 pF
I C bus
OSCI OSCO
SCL
SDA
PCD3312C
TONE
A
V
V
DD
0
SS
MGG544
Fig.24 PCD3312C driven by microcontroller PCF84C21A. The PCF84C21A is a single-chip 8-bit microcontroller
with 2 kbytes ROM and I2C-bus. The same application is possible with the PCD3311C with MODE = VSS
.
1996 Nov 21
21
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
13 PACKAGE OUTLINES
DIP14: plastic dual in-line package; 14 leads (300 mil)
SOT27-1
D
M
E
A
2
A
A
1
L
c
e
w M
Z
b
1
(e )
1
b
M
H
14
8
pin 1 index
E
1
7
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
(1)
A
A
A
2
(1)
(1)
Z
1
UNIT
mm
b
b
c
D
E
e
e
L
M
M
H
w
1
1
E
max.
min.
max.
max.
1.73
1.13
0.53
0.38
0.36
0.23
19.50
18.55
6.48
6.20
3.60
3.05
8.25
7.80
10.0
8.3
4.2
0.51
3.2
2.54
0.10
7.62
0.30
0.254
0.01
2.2
0.068
0.044
0.021
0.015
0.014
0.009
0.77
0.73
0.26
0.24
0.14
0.12
0.32
0.31
0.39
0.33
inches
0.17
0.020
0.13
0.087
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
92-11-17
95-03-11
SOT27-1
050G04
MO-001AA
1996 Nov 21
22
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
SO16: plastic small outline package; 16 leads; body width 7.5 mm
SOT162-1
D
E
A
X
c
H
v
M
A
E
y
Z
16
9
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
8
detail X
e
w
M
b
p
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
max.
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
θ
1
2
3
p
E
p
Z
0.30
0.10
2.45
2.25
0.49
0.36
0.32
0.23
10.5
10.1
7.6
7.4
10.65
10.00
1.1
0.4
1.1
1.0
0.9
0.4
mm
2.65
1.27
0.050
1.4
0.25
0.01
0.25
0.1
0.25
0.01
8o
0o
0.012 0.096
0.004 0.089
0.019 0.013 0.41
0.014 0.009 0.40
0.30
0.29
0.42
0.39
0.043 0.043
0.016 0.039
0.035
0.016
inches 0.10
0.055
0.01 0.004
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
92-11-17
95-01-24
SOT162-1
075E03
MS-013AA
1996 Nov 21
23
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
DIP8: plastic dual in-line package; 8 leads (300 mil)
SOT97-1
D
M
E
A
2
A
A
1
L
c
w M
Z
b
1
e
(e )
1
M
H
b
b
2
8
5
pin 1 index
E
1
4
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
(1)
A
A
A
2
(1)
(1)
Z
1
w
UNIT
mm
b
b
b
c
D
E
e
e
L
M
M
H
1
2
1
E
max.
min.
max.
max.
1.73
1.14
0.53
0.38
1.07
0.89
0.36
0.23
9.8
9.2
6.48
6.20
3.60
3.05
8.25
7.80
10.0
8.3
4.2
0.51
3.2
2.54
0.10
7.62
0.30
0.254
0.01
1.15
0.068 0.021 0.042 0.014
0.045 0.015 0.035 0.009
0.39
0.36
0.26
0.24
0.14
0.12
0.32
0.31
0.39
0.33
inches
0.17
0.020
0.13
0.045
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
92-11-17
95-02-04
SOT97-1
050G01
MO-001AN
1996 Nov 21
24
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
SO8: plastic small outline package; 8 leads; body width 7.5 mm
SOT176-1
D
E
A
X
c
y
H
v
M
A
E
Z
8
5
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
4
detail X
e
w
M
b
p
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
θ
1
2
3
p
E
Z
max.
0.3
0.1
2.45
2.25
0.49
0.36
0.32
0.23
7.65
7.45
7.6
7.4
10.65
10.00
1.1
0.45
1.1
1.0
2.0
1.8
mm
2.65
0.25
0.01
1.27
0.050
1.45
0.057
0.25
0.01
0.25
0.1
8o
0o
0.012 0.096
0.004 0.089
0.019 0.013 0.30
0.014 0.009 0.29
0.30
0.29
0.42
0.39
0.043 0.043
0.018 0.039
0.079
0.071
inches 0.10
0.01 0.004
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
91-08-13
95-02-25
SOT176-1
1996 Nov 21
25
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
14 SOLDERING
14.1 Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
14.3.2 WAVE SOLDERING
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
14.2 DIP
14.2.1 SOLDERING BY DIPPING OR BY WAVE
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
• The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
14.2.2 REPAIRING SOLDERED JOINTS
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
14.3.3 REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
14.3 SO
14.3.1 REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
1996 Nov 21
26
Philips Semiconductors
Product specification
DTMF/modem/musical-tone generators
PCD3311C; PCD3312C
15 DEFINITIONS
Data sheet status
Objective specification
Preliminary specification
Product specification
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
16 LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
17 PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
1996 Nov 21
27
Philips Semiconductors – a worldwide company
Argentina: see South America
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Belgium: see The Netherlands
Brazil: see South America
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Portugal: see Spain
Romania: see Italy
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 247 9145, Fax. +7 095 247 9144
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Colombia: see South America
Czech Republic: see Austria
Slovakia: see Austria
Slovenia: see Italy
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 1949
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580/xxx
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66,
Chung Hsiao West Road, Sec. 1, P.O. Box 22978,
TAIPEI 100, Tel. +886 2 382 4443, Fax. +886 2 382 4444
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180,
Tel. +972 3 645 0444, Fax. +972 3 649 1007
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Uruguay: see South America
Vietnam: see Singapore
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
Middle East: see Italy
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Internet: http://www.semiconductors.philips.com
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
© Philips Electronics N.V. 1996
SCA52
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
417021/1200/02/pp28
Date of release: 1996 Nov 21
Document order number: 9397 750 01155
相关型号:
©2020 ICPDF网 联系我们和版权申明