PIMXRT506LXVN4A [NXP]
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products;![PIMXRT506LXVN4A](http://pdffile.icpdf.com/pdf2/p00353/img/icpdf/PIMXRT106ADJ_2172426_icpdf.jpg)
型号: | PIMXRT506LXVN4A |
厂家: | ![]() |
描述: | i.MX RT1015 Crossover Processors Data Sheet for Consumer Products |
文件: | 总71页 (文件大小:1093K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
Document Number: IMXRT1015CEC
Rev. 2, 03/2021
NXP Semiconductors
Data Sheet: Technical Data
MIMXRT1015DAF5A
i.MX RT1015 Crossover
Processors Data Sheet
for Consumer Products
Package Information
Plastic Package
100-Pin LQFP, 14 x 14 mm, 0.5 mm pitch
Ordering Information
See Table 1 on page 4
1 i.MX RT1015 introduction
The i.MX RT1015 is a processor of i.MX RT family
featuring NXP’s advanced implementation of the Arm
1. i.MX RT1015 introduction . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2. Ordering information . . . . . . . . . . . . . . . . . . . . . . . 4
2. Architectural overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Modules list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1. Special signal considerations . . . . . . . . . . . . . . . 12
3.2. Recommended connections for unused analog
®
®
Cortex -M7 core, which operates at speeds up to 500
MHz to provide high CPU performance and real-time
response.
The i.MX RT1015 processor has 128 KB on-chip RAM,
which can be flexibly configured as TCM or
interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4. Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1. Chip-level conditions . . . . . . . . . . . . . . . . . . . . . . 14
4.2. System power and clocks . . . . . . . . . . . . . . . . . . 20
4.3. I/O parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.4. System modules . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.5. External memory interface . . . . . . . . . . . . . . . . . 36
4.6. Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.7. Analog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.8. Communication interfaces . . . . . . . . . . . . . . . . . . 51
4.9. Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5. Boot mode configuration . . . . . . . . . . . . . . . . . . . . . . . . 57
5.1. Boot mode configuration pins . . . . . . . . . . . . . . . 57
5.2. Boot device interface allocation . . . . . . . . . . . . . . 57
6. Package information and contact assignments . . . . . . . 60
6.1. 14 x 14 mm package information . . . . . . . . . . . . 60
7. Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
general-purpose on-chip RAM. The i.MX RT1015
integrates advanced power management module with
DCDC and LDO that reduces complexity of external
power supply and simplifies power sequencing. The
i.MX RT1015 also provides various memory interfaces,
including Quad SPI, and a wide range of connectivity
interfaces including UART, SPI, I2C, and USB; for
connecting peripherals including Bluetooth™, and GPS.
The i.MX RT1015 also has rich audio features, including
SPDIF and I2S audio interface. Various analog IP
integration, including ADC, temperature sensor, etc.
NXP reserves the right to change the production detail specifications as may be required
to permit improvements in the design of its products.
© 2019-2021 NXP B.V.
i.MX RT1015 introduction
The i.MX RT1015 is specifically useful for applications such as:
•
•
•
•
•
Industrial
Motor Control
Home Appliance
Audio
IoT
1.1
Features
The i.MX RT1015 processors are based on Arm Cortex-M7 Core™ Platform, which has the following
features:
•
Supports single Arm Cortex-M7 with:
— 16 KB L1 Instruction Cache
— 16 KB L1 Data Cache
— Full featured Floating Point Unit (FPU) with support of the VFPv5 architecture
— Support the Armv7-M Thumb instruction set
Integrated MPU, up to 16 individual protection regions
Up to 128 KB I-TCM and D-TCM in total
•
•
•
•
•
Frequency of 500 MHz
Cortex M7 CoreSight™ components integration for debug
Frequency of the core, as per Table 9, "Operating ranges," on page 16.
The SoC-level memory system consists of the following additional components:
— Boot ROM (96 KB)
— On-chip RAM (128 KB)
– Configurable RAM size up to 128 KB shared with CM7 TCM
•
•
External memory interfaces:
— SPI NOR/NAND FLASH
— Parallel NOR FLASH with XIP support
— Single/Dual channel Quad SPI FLASH with XIP support
Timers and PWMs:
— Two General Programmable Timers
– 4-channel generic 32-bit resolution timer
– Each support standard capture and compare operation
— Four Periodical Interrupt Timers
– Generic 32-bit resolution timer
– Periodical interrupt generation
— One Quad Timer
– 4-channel generic 16-bit resolution timer
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
2
NXP Semiconductors
i.MX RT1015 introduction
– Each support standard capture and compare operation
– Quadrature decoder integrated
— One FlexPWM
– Up to 8 individual PWM channels
– 16-bit resolution PWM suitable for Motor Control applications
— One Quadrature Encoder/Decoder
Each i.MX RT1015 processor enables the following interfaces to external devices (some of them are
muxed and not available simultaneously):
•
Audio:
— S/PDIF input and output
— Three synchronous audio interface (SAI) modules supporting I2S, AC97, TDM, and
codec/DSP interfaces
— MQS interface for medium quality audio via GPIO pads
Connectivity:
•
— One USB 2.0 OTG controller with integrated PHY interface
— Four universal asynchronous receiver/transmitter (UARTs) modules
— Two I2C modules
— Two SPI modules
•
GPIO and Pin Multiplexing:
— General-purpose input/output (GPIO) modules with interrupt capability
— Input/output multiplexing controller (IOMUXC) to provide centralized pad control
— 57 GPIOs
— One FlexIO
The i.MX RT1015 processors integrate advanced power management unit and controllers:
•
•
•
Full PMIC integration, including on-chip DCDC and LDOs
Temperature sensor with programmable trip points
GPC hardware power management controller
The i.MX RT1015 processors support the following system debug:
•
•
•
Arm CortexM7 CoreSight debug and trace architecture
Trace Port Interface Unit (TPIU) to support off-chip real-time trace
Support for 5-pin (JTAG) and SWD debug interfaces selected by eFuse
Security functions are enabled and accelerated by the following hardware:
•
•
High Assurance Boot (HAB)
Data Co-Processor (DCP):
— AES-128, ECB, and CBC mode
— SHA-1 and SHA-256
— CRC-32
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
3
i.MX RT1015 introduction
•
Bus Encryption Engine (BEE)
— AES-128, ECB, and CTR mode
— On-the-fly QSPI Flash decryption
True random number generation (TRNG)
Secure Non-Volatile Storage (SNVS)
— Secure real-time clock (RTC)
— Zero Master Key (ZMK)
•
•
•
Secure JTAG Controller (SJC)
NOTE
The actual feature set depends on the part numbers as described in Table 1.
Functions such as display and camera interfaces, connectivity interfaces,
and security features are not offered on all derivatives.
1.2
Ordering information
Table 1 provides examples of orderable part numbers covered by this data sheet.
Table 1. Ordering information
Junction
Temperature Tj (C)
Part Number
Feature
Features supports:
Package
MIMXRT1015DAF5A
14 x 14 mm, 0.5 mm pitch,
0 to +95
• 500 MHz, consumer grade for general 100-pin LQFP
purpose
• 128K RAM
• USB OTG x1
• SAI x3
• SPDIF x1
• General Purpose Timer x2
• PWM x1
• UART x4
• I2C x2
• SPI x2
• ADC x1
• MQS x1
• FlexIO x1
• QTimer x1
• ENC x1
• DCDC
• TRNG x1
• Quad-SPI x1
• WDOG x4
• Security RTC
• 57 GPIOs
Figure 1 describes the part number nomenclature so that characteristics of a specific part number can be
identified (for example, cores, frequency, temperature grade, fuse options, and silicon revision). The
primary characteristic which describes which data sheet applies to a specific part is the temperature grade
(junction) field.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
4
NXP Semiconductors
i.MX RT1015 introduction
Ensure to have the proper data sheet for specific part by verifying the temperature grade (junction) field
and matching it to the proper data sheet. If there are any questions, visit the web page nxp.com/IMXRT or
contact an NXP representative for details.
M
IMX X X
@
##
%
+
VV
$
A
Qualification Level
M
Silicon Rev
A
A
B
Prototype Samples
Mass Production
Special
P
M
S
A0
A1
Core Frequency
400 MHz
$
4
5
6
Part # series
XX
i.MX RT
RT
500 MHz
@
1
Family
600 MHz
First Generation RT family
Reserved
Package Type
VV
2-8
225MAPBGA, 13 x 13 mm, 0.8 mm pitch
VN
Sub-Family
RT101x
##
196MAPBGA, 12 x 12 mm, 0.8 mm pitch
196MAPBGA, 10 x 10 mm, 0.65 mm pitch
169MAPBGA, 11 x 11 mm, 0.8 mm pitch
169MAPBGA, 9 x 9 mm, 0.65 mm pitch
144LQFP, 20 x 20 mm, 0.5 mm pitch
100LQFP, 14 x 14 mm, 0.5 mm pitch
80LQFP, 12 x 12 mm, 0.5 mm pitch
VJ
VL
JM
FP
AG
AF
AE
01
02
04
05
06
RT102x
RT104x
Tie
%
1
RT105x
Standard Feature
Full Feature
RT106x
2
4MB Flash SIP
Enhanced Feature
Far Field AFE
4
5
Temperature (Tj)
+
D
C
X
A
F
L
Consumer: 0 to + 95 °C
Facial Recognition
Local Voice Control (audio input models)
Industrial: -40 to +105 °C
Extended Industrial: -40 to +125 eC
Local Voice Control (text input models)
S
Figure 1. Part number nomenclature—i.MX RT10XX family
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
5
Architectural overview
2 Architectural overview
The following subsections provide an architectural overview of the i.MX RT1015 processor system.
2.1
Block diagram
1
Figure 2 shows the functional modules in the i.MX RT1015 processor system .
System Control
CPU Platform
Connectivity
Secure JTAG
ARM Cortex-M7
UART x4
PLL / OSC
16 KB D-cache
NVIC
16 KB I-cache
FPU MPU
4 x 4 Keypad
I2C x2
RTC and Reset
Enhanced DMA
IOMUX
Up to 128 KB TCM
SPI x2
GP Timer x6
(GPT x2 + PIT x4)
External Memory
GPIO
Quadrature ENC x1
QuadTimer x1
Dual-Channel Quad-SPI
(FlexSPI)
I2S / SAI x3
FlexPWM x1
USB2.0 OTG with PHY
S/PDIF Tx/Rx
Security
Watch Dog x4
HAB
eFUSE
Internal Memory
128 KB OCRAM
shared with TCM
ADC
Secure RTC
Ciphers and RNG
ADC (9-Channel) x1
96 KB ROM
DCDC
Power Management
LDO
Temp Monitor
.
Figure 2. i.MX RT1015 system block diagram
1. Some modules shown in this block diagram are not offered on all derivatives. See Table 1 for details.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
6
NXP Semiconductors
Modules list
3 Modules list
The i.MX RT1015 processors contain a variety of digital and analog modules. Table 2 describes these
modules in alphabetical order.
Table 2. i.MX RT1015 modules list
Block mnemonic
Block name
Subsystem
Analog
Brief description
ADC1
Analog to Digital
Converter
The ADC is a 12-bit general purpose analog to digital
converter.
AOI
Arm
And-Or-Inverter
Arm Platform
Cross Trigger
The AOI provides a universal boolean function
generator using a four team sum of products expression
with each product term containing true or complement
values of the four selected inputs (A, B, C, D).
Arm
The Arm Core Platform includes 1x Cortex-M7 core. It
also includes associated sub-blocks, such as Nested
Vectored Interrupt Controller (NVIC), Floating-Point
Unit (FPU), Memory Protection Unit (MPU), and
CoreSight debug modules.
BEE
Bus Encryption Engine
Security
On-The-Fly FlexSPI Flash Decryption
CCM
GPC
SRC
Clock Control Module,
General Power
Controller, System Reset
Controller
Clocks, Resets, and These modules are responsible for clock and reset
Power Control
distribution in the system, and also for the system
power management.
CSU
DAP
Central Security Unit
Debug Access Port
Security
The Central Security Unit (CSU) is responsible for
setting comprehensive security policy within the i.MX
RT1015 platform.
System Control
Peripherals
The DAP provides real-time access for the debugger
without halting the core to:
• System memory and peripheral registers
• All debug configuration registers
The DAP also provides debugger access to JTAG scan
chains. The DAP module is internal to the Cortex-M7
Core Platform.
DCDC
DCDC Converter
Analog
The DCDC module is used for generating power supply
for core logic. Main features are:
• Adjustable high efficiency regulator
• Supports 3.3 V input voltage
• Supports nominal run and low power standby modes
• Supports at 0.9 ~ 1.3 V output in run mode
• Supports at 0.9 ~ 1.0 V output in standby mode
• Over current and over voltage detection
eDMA
enhanced Direct Memory System Control
Access Peripherals
There is an enhanced DMA (eDMA) engine and two
DMA_MUX.
• The eDMA is a 32 channel DMA engine, which is
capable of performing complex data transfers with
minimal intervention from a host processor.
• The DMA_MUX is capable of multiplexing up to 128
DMA request sources to the 32 DMA channels of
eDMA.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
7
Modules list
Table 2. i.MX RT1015 modules list (continued)
Block mnemonic
Block name
Subsystem
Brief description
ENC
Quadrature
Encoder/Decoder
Timer Peripherals
The enhanced quadrature encoder/decoder module
provides interfacing capability to position/speed
sensors. There are five input signals: PHASEA,
PHASEB, INDEX, TRIGGER, and HOME. This module
is used to decode shaft position, revolution count, and
speed.
EWM
External Watchdog
Monitor
Timer Peripherals
The EWM modules is designed to monitor external
circuits, as well as the software flow. This provides a
back-up mechanism to the internal WDOG that can
reset the system. The EWM differs from the internal
WDOG in that it does not reset the system. The EWM,
if allowed to time-out, provides an independent trigger
pin that when asserted resets or places an external
circuit into a safe mode.
FlexIO1
Flexible Input/output
Connectivity and
Communications
The FlexIO is capable of supporting a wide range of
protocols including, but not limited to: UART, I2C, SPI,
I2S, camera interface, display interface, PWM
waveform generation, etc. The module can remain
functional when the chip is in a low power mode
provided the clock it is using remain active.
FlexPWM1
FlexRAM
Pulse Width Modulation Timer Peripherals
The pulse-width modulator (PWM) contains four PWM
sub-modules, each of which is set up to control a single
half-bridge power stage. Fault channel support is
provided. The PWM module can generate various
switching patterns, including highly sophisticated
waveforms.
RAM
Memories
The i.MX RT1015 has 128 KB of on-chip RAM which
could be flexible allocated to I-TCM, D-TCM, and
on-chip RAM (OCRAM) in a 32 KB granularity. The
FlexRAM is the manager of the 128 KB on-chip RAM
array. Major functions of this blocks are: interfacing to
I-TCM and D-TCM of Arm core and OCRAM controller;
dynamic RAM arrays allocation for I-TCM, D-TCM, and
OCRAM.
FlexSPI
Quad Serial Peripheral
Interface
Connectivity and
Communications
FlexSPI acts as an interface to one or two external
serial flash devices, each with up to four bidirectional
data lines.
GPIO1
GPIO2
GPIO3
GPIO5
General Purpose I/O
Modules
System Control
Peripherals
Used for general purpose input/output to external ICs.
Each GPIO module supports up to 32 bits of I/O.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
8
Modules list
Table 2. i.MX RT1015 modules list (continued)
Block mnemonic
Block name
General Purpose Timer
Subsystem
Brief description
GPT1
GPT2
Timer Peripherals
Each GPT is a 32-bit “free-running” or “set and forget”
mode timer with programmable prescaler and compare
and capture register. A timer counter value can be
captured using an external event and can be configured
to trigger a capture event on either the leading or trailing
edges of an input pulse. When the timer is configured to
operate in “set and forget” mode, it is capable of
providing precise interrupts at regular intervals with
minimal processor intervention. The counter has output
compare logic to provide the status and interrupt at
comparison. This timer can be configured to run either
on an external clock or on an internal clock.
KPP
Keypad Port
Human Machine
Interfaces
The KPP is a 16-bit peripheral that can be used as a
keypad matrix interface or as general purpose
input/output (I/O). It supports 4 x 4 external key pad
matrix. Main features are:
• Multiple-key detection
• Long key-press detection
• Standby key-press detection
• Supports a 2-point and 3-point contact key matrix
LPI2C1
LPI2C2
Low Power
Inter-integrated Circuit
Connectivity and
Communications
The LPI2C is a low power Inter-Integrated Circuit (I2C)
module that supports an efficient interface to an I2C bus
as a master.
The I2C provides a method of communication between
a number of external devices. More detailed
information, see Section 4.8.2, LPI2C module timing
parameters.
LPSPI1
LPSPI2
Low Power Serial
Peripheral Interface
Connectivity and
Communications
The LPSPI is a low power Serial Peripheral Interface
(SPI) module that support an efficient interface to an
SPI bus as a master and/or a slave.
• It can continue operating while the chip is in stop
modes, if an appropriate clock is available
• Designed for low CPU overhead, with DMA off
loading of FIFO register access
LPUART1
LPUART2
LPUART3
LPUART4
UART Interface
Connectivity
Peripherals
Each of the UART modules support the following serial
data transmit/receive protocols and configurations:
• 7- or 8-bit data words, 1 or 2 stop bits, programmable
parity (even, odd or none)
• Programmable baud rates up to 20 Mbps.
MQS
Medium Quality Sound
Multimedia
Peripherals
MQS is used to generate 2-channel medium quality
PWM-like audio via two standard digital GPIO pins.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
9
Modules list
Table 2. i.MX RT1015 modules list (continued)
Block mnemonic
Block name
Subsystem
Brief description
QuadTimer1
QuadTimer
Timer Peripherals
The quad-timer provides four timer channels with a
variety of controls affecting both individual and
multi-channel features.Specific features include
up/down count, cascading of counters, programmable
module, count once/repeated, counter preload,
compare registers with preload, shared use of input
signals, prescaler controls, independent
capture/compare, fault input control, programmable
input filters, and multi-channel synchronization.
ROMCP
ROM Controller with
Patch
Memories and
The ROMCP acts as an interface between the Arm
Memory Controllers advanced high-performance bus and the ROM. The
on-chip ROM is only used by the Cortex-M7 core during
boot up. Size of the ROM is 96 KB.
RTC OSC
RTWDOG
Real Time Clock
Oscillator
Clock Sources and The RTC OSC provides the clock source for the
Control
Real-Time Clock module. The RTC OSC module, in
conjunction with an external crystal, generates a 32.768
kHz reference clock for the RTC.
Watch Dog
Timer Peripherals
The RTWDG module is a high reliability independent
timer that is available for system to use. It provides a
safety feature to ensure software is executing as
planned and the CPU is not stuck in an infinite loop or
executing unintended code. If the WDOG module is not
serviced (refreshed) within a certain period, it resets the
MCU. Windowed refresh mode is supported as well.
SAI1
SAI2
SAI3
Synchronous Audio
Interface
Multimedia
Peripherals
The SAI module provides a synchronous audio
interface (SAI) that supports full duplex serial interfaces
with frame synchronization, such as I2S, AC97, TDM,
and codec/DSP interfaces.
SA-TRNG
SJC
StandaloneTrueRandom Security
Number Generator
The SA-TRNG is hardware accelerator that generates
a 512-bit entropy as needed by an entropy consuming
module or by other post processing functions.
System JTAG Controller System Control
Peripherals
The SJC provides JTAG interface, which complies with
JTAG TAP standards, to internal logic. The i.MX
RT1015 processors use JTAG port for production,
testing, and system debugging. In addition, the SJC
provides BSR (Boundary Scan Register) standard
support, which complies with IEEE1149.1 and
IEEE1149.6 standards.
The JTAG port is accessible during platform initial
laboratory bring-up, for manufacturing tests and
troubleshooting, as well as for software debugging by
authorized entities. The i.MX RT1015 SJC incorporates
three security modes for protecting against
unauthorized accesses. Modes are selected through
eFUSE configuration.
SNVS
Secure Non-Volatile
Storage
Security
Secure Non-Volatile Storage, including Secure Real
Time Clock, Security State Machine, and Master Key
Control.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
10
Modules list
Table 2. i.MX RT1015 modules list (continued)
Block name Subsystem Brief description
Multimedia
Block mnemonic
SPDIF
Sony Philips Digital
Interconnect Format
A standard audio file transfer format, developed jointly
by the Sony and Phillips corporations. Has Transmitter
and Receiver functionality.
Peripherals
Temp Monitor
USBO2
Temperature Monitor
Analog
The temperature sensor implements a temperature
sensor/conversion function based on a
temperature-dependent voltage to time conversion.
Universal Serial Bus 2.0 Connectivity
Peripherals
USBO2 (USB OTG1) contains:
• One high-speed OTG 2.0 module with integrated HS
USB PHYs
• Support eight Transmit (TX) and eight Receive (Rx)
endpoints, including endpoint 0
WDOG1
WDOG2
Watch Dog
Cross BAR
Timer Peripherals
The Watch Dog Timer supports two comparison points
during each counting period. Each of the comparison
points is configurable to evoke an interrupt to the Arm
core, and a second point evokes an external event on
the WDOG line.
XBAR
Cross Trigger
Each crossbar switch is an array of muxes with shared
inputs. Each mux output provides one output of the
crossbar. The number of inputs and the number of
muxes/outputs are user configurable and registers are
provided to select which of the shared inputs are routed
to each output.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
11
Modules list
3.1
Special signal considerations
Table 3 lists special signal considerations for the i.MX RT1015 processors. The signal names are listed in
alphabetical order.
The package contact assignments can be found in Section 6, Package information and contact
assignments. Signal descriptions are provided in the i.MX RT1015 Reference Manual (IMXRT1015RM).
Table 3. Special signal considerations
Signal name
Remarks
DCDC_PSWITCH
PAD is in DCDC_IN domain and connected the ground to bypass DCDC.
To enable DCDC function, assert to DCDC_IN with at least 1ms delay for DCDC_IN rising edge.
RTC_XTALI/RTC_XTALO If the user wishes to configure RTC_XTALI and RTC_XTALO as an RTC oscillator, a 32.768 kHz
crystal, (100 k ESR, 10 pF load) should be connected between RTC_XTALI and RTC_XTALO.
Keep in mind the capacitors implemented on either side of the crystal are about twice the crystal
load capacitor. To hit the exact oscillation frequency, the board capacitors need to be reduced to
account for board and chip parasitics. The integrated oscillation amplifier is self biasing, but
relatively weak. Care must be taken to limit parasitic leakage from RTC_XTALI and RTC_XTALO
to either power or ground (>100 M). This will debias the amplifier and cause a reduction of
startup margin. Typically RTC_XTALI and RTC_XTALO should bias to approximately 0.5 V.
If it is desired to feed an external low frequency clock into RTC_XTALI the RTC_XTALO pin must
remain unconnected or driven with a complimentary signal. The logic level of this forcing clock
should not exceed VDD_SNVS_CAP level and the frequency should be <100 kHz under typical
conditions.
In case when high accuracy real time clock are not required system may use internal low
frequency ring oscillator. It is recommended to connect RTC_XTALI to GND and keep
RTC_XTALO unconnected.
XTALI/XTALO
A 24.0 MHz crystal should be connected between XTALI and XTALO. External load capacitance
value depends on the typical load capacitance of crystal used and PCB design.
The crystal must be rated for a maximum drive level of 250 W. An ESR (equivalent series
resistance) of typical 80 is recommended. NXP SDK software requires 24 MHz on
XTALI/XTALO.
The crystal can be eliminated if an external 24 MHz oscillator is available in the system. In this
case, XTALO must be directly driven by the external oscillator and XTALI mounted with 18 pF
capacitor. The logic level of this forcing clock cannot exceed NVCC_PLL level.
If this clock is used as a reference for USB, then there are strict frequency tolerance and jitter
requirements. See OSC24M chapter and relevant interface specifications chapters for details.
GPANAIO
This signal is reserved for NXP manufacturing use only. This output must remain unconnected.
JTAG_nnnn
The JTAG interface is summarized in Table 4. Use of external resistors is unnecessary. However,
if external resistors are used, the user must ensure that the on-chip pull-up/down configuration is
followed. For example, do not use an external pull down on an input that has on-chip pull-up.
JTAG_TDO is configured with a keeper circuit such that the non-connected condition is eliminated
if an external pull resistor is not present. An external pull resistor on JTAG_TDO is detrimental and
should be avoided.
JTAG_MOD is referenced as SJC_MOD in the i.MX RT1015 reference manual. Both names refer
to the same signal. JTAG_MOD must be externally connected to GND for normal operation.
Termination to GND through an external pull-down resistor (such as 1 k) is allowed. JTAG_MOD
set to hi configures the JTAG interface to mode compliant with IEEE1149.1 standard. JTAG_MOD
set to low configures the JTAG interface for common SW debug adding all the system TAPs to the
chain.
NC
These signals are No Connect (NC) and should be disconnected by the user.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
12
NXP Semiconductors
Modules list
Table 3. Special signal considerations (continued)
Signal name
POR_B
Remarks
This cold reset negative logic input resets all modules and logic in the IC.
May be used in addition to internally generated power on reset signal (logical AND, both internal
and external signals are considered active low).
ONOFF
ONOFF can be configured in debounce, off to on time, and max time-out configurations. The
debounce and off to on time configurations supports 0, 50, 100 and 500 ms. Debounce is used to
generate the power off interrupt. While in the ON state, if ONOFF button is pressed longer than
the debounce time, the power off interrupt is generated. Off to on time supports the time it takes
to request power on after a configured button press time has been reached. While in the OFF
state, if ONOFF button is pressed longer than the off to on time, the state will transition from OFF
to ON. Max time-out configuration supports 5, 10, 15 seconds and disable. Max time-out
configuration supports the time it takes to request power down after ONOFF button has been
pressed for the defined time.
TEST_MODE
WAKEUP
TEST_MODE is for NXP factory use. The user can leave this signal floating or tie it to ground.
A GPIO powered by SNVS domain power supply which can be configured as wakeup source in
SNVS mode.
Table 4. JTAG controller interface summary
JTAG
I/O type
On-chip termination
100 kpull-down
JTAG_TCK
JTAG_TMS
JTAG_TDI
Input
Input
47 kpull-up
47 kpull-up
Keeper
Input
JTAG_TDO
JTAG_TRSTB
JTAG_MOD
3-state output
Input
47 kpull-up
100 kpull-down
Input
3.2
Recommended connections for unused analog interfaces
Table 5 shows the recommended connections for unused analog interfaces.
Table 5. Recommended connections for unused analog interfaces
Recommendations
if unused
Module
Pad name
USB
ADC
USB_OTG1_CHD_B, USB_OTG1_DN, USB_OTG1_DP, USB_OTG1_VBUS
VDDA_ADC_3P3
Not connected
VDDA_ADC_3P3
must be powered
even if the ADC is
not used.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
13
Electrical characteristics
4 Electrical characteristics
This section provides the device and module-level electrical characteristics for the i.MX RT1015
processors.
4.1
Chip-level conditions
This section provides the device-level electrical characteristics for the IC. See Table 6 for a quick reference
to the individual tables and sections.
Table 6. i.MX RT1015 chip-Level conditions
For these characteristics
Topic appears
Absolute maximum ratings
Thermal resistance
on page 14
on page 15
on page 16
on page 17
on page 18
on page 19
on page 19
Operating ranges
External clock sources
Maximum supply currents
Low power mode supply currents
USB PHY current consumption
4.1.1
Absolute maximum ratings
CAUTION
Stress beyond those listed under Table 7 may cause permanent damage to the device. These are stress
ratings only. Functional operation of the device at these or any other conditions beyond those indicated
under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated
conditions for extended periods may affect device reliability.
Table 7 shows the absolute maximum operating ratings.
Table 7. Absolute maximum ratings
Parameter Description
Core supplies input voltage
Symbol
VDD_SOC_IN
Min
Max
Unit
-0.3
-0.3
-0.3
-0.3
1.6
3.7
3.6
3.6
V
V
V
V
VDD_HIGH_IN supply voltage
Power for DCDC
VDD_HIGH_IN
DCDC_IN
Supply input voltage to Secure Non-Volatile Storage VDD_SNVS_IN
and Real Time Clock
USB VBUS supply
USB_OTG1_VBUS
VDDA_ADC
—
3
5.5
3.6
3.6
V
V
V
Supply for 12-bit ADC
IO supply for GPIO bank (3.3 V mode)
NVCC_GPIO
3
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
14
Electrical characteristics
Table 7. Absolute maximum ratings (continued)
ESD Damage Immunity:
Vesd
Human Body Model (HBM)
Charge Device Model (CDM)
—
—
1000
500
V
Input/Output Voltage range
Storage Temperature range
Vin/Vout
-0.5
-40
OVDD + 0.31
150
V
TSTORAGE
o C
1
OVDD is the I/O supply voltage.
4.1.2
Thermal resistance
Following sections provide the thermal resistance data.
4.1.2.1 14 x 14 mm package thermal resistance
Table 8 displays the 14 x 14 mm LQFP package thermal resistance data.
Table 8. 14 x 14 mm package thermal resistance data
Rating
Test Conditions
Single-layer board (1s)
Symbol
RJA
Value
Unit
oC/W
Notes
1,2
Junction to Ambient
Natural convection
63
52
53
46
1,2
1,3
1,3
Junction to Ambient
Natural convection
Four-layer board (2s2p)
RJA
oC/W
oC/W
oC/W
Junction to Ambient (@200 Single layer board (1s)
ft/min)
RJMA
RJMA
Junction to Ambient (@200 Four layer board (2s2p)
ft/min)
4
5
6
Junction to Board
—
RJB
RJC
JT
36
19
3
oC/W
oC/W
oC/W
Junction to Case
—
Junction to Package Top
Natural Convection
1
Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal
resistance.
2
3
4
5
6
Per JEDEC JESD51-2 with natural convection for horizontally oriented board. Board meets JESD51-9 specification for 1s or
2s2p board, respectively.
Per JEDEC JESD51-6 with forced convection for horizontally oriented board. Board meets JESD51-9 specification for 1s or
2s2p board, respectively.
Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method
1012.1).
Thermal characterization parameter indicating the temperature difference between package top and the junction temperature
per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
15
Electrical characteristics
4.1.3
Operating ranges
Table 9 provides the operating ranges of the i.MX RT1015 processors. For details on the chip's power
structure, see the “Power Management Unit (PMU)” chapter of the i.MX RT1015 Reference Manual
(IMXRT1015RM).
Table 9. Operating ranges
Parameter
Description
Operating
Conditions
Symbol
Min
Typ Max1 Unit
Comment
Run Mode
VDD_SOC_IN
VDD_SOC_IN
Overdrive
1.25
1.15
—
—
1.3
1.3
V
V
—
—
M7 core at 396
MHz
M7 core at 132
MHz
1.15
0.925
1.15
—
—
—
1.3
1.3
1.3
M7 core at 24
MHz
IDLE Mode
VDD_SOC_IN
M7 core
V
—
operation at 396
MHz or below
SUSPEND (DSM) VDD_SOC_IN
Mode
—
0.925
—
1.3
V
V
Refer to Table 12 Low power mode
current and power consumption
SNVS Mode
VDD_SOC_IN
DCDC_IN
—
—
—
0
1.3
3.6
3.6
—
—
Power for DCDC
3.0
3.0
3.3
—
VDD_HIGH
VDD_HIGH_IN2
V
V
Must match the range of voltages
that the rechargeable backup
battery supports.
internal regulator
Backup battery
supply range
VDD_SNVS_IN3
—
2.40
—
3.6
Can be combined with
VDDHIGH_IN, if the system does
not require keeping real time and
other data on OFF state.
USB supply
voltages
USB_OTG1_VBUS —
4.40
3.0
—
5.5
3.6
V
V
—
GPIO supplies
A/D converter
NVCC_GPIO
—
3.3
All digital I/O supplies
(NVCC_xxxx) must be powered
(unless otherwise specified in this
data sheet) under normal
conditions whether the associated
I/O pins are in use or not.
VDDA_ADC_3P3
—
3.0
3.3
3.6
V
VDDA_ADC_3P3 must be
powered even if the ADC is not
used.
VDDA_ADC_3P3 cannot be
powered when the other SoC
supplies (except VDD_SNVS_IN)
are off.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
16
Electrical characteristics
Table 9. Operating ranges (continued)
System frequency/ FSYS/FBUS
Bus frequency
—
500/ 396/ 24/
MHz
—
125
132
24
Temperature Operating Ranges
Junction
temperature
Tj
Standard
Commercial
0
—
95
oC
See the application note, i.MX
RT1015 Product Lifetime Usage
Estimates for information on
product lifetime (power-on years)
for this processor.
1
2
3
Applying the maximum voltage results in maximum power consumption and heat generation. NXP recommends a voltage set
point = (Vmin + the supply tolerance). This result in an optimized power/speed ratio.
Applying the maximum voltage results in shorten lifetime. 3.6 V usage limited to < 1% of the use profile. Reset of profile limited
to below 3.49 V.
In setting VDD_SNVS_IN voltage with regards to Charging Currents and RTC, refer to the i.MX RT1015 Hardware
Development Guide (IMXRT1015HDG).
4.1.4
External clock sources
Each i.MX RT1015 processor has two external input system clocks: a low frequency (RTC_XTALI) and
a high frequency (XTALI).
The RTC_XTALI is used for low-frequency functions. It supplies the clock for wake-up circuit,
power-down real time clock operation, and slow system and watch-dog counters. The clock input can be
connected to either external oscillator or a crystal using internal oscillator amplifier. Additionally, there is
an internal ring oscillator, which can be used instead of the RTC_XTALI if accuracy is not important.
The system clock input XTALI is used to generate the main system clock. It supplies the PLLs and other
peripherals. The system clock input can be connected to either external oscillator or a crystal using internal
oscillator amplifier.
Table 10 shows the interface frequency requirements.
Table 10. External input clock frequency
Parameter Description
Symbol
Min
Typ
Max
Unit
RTC_XTALI Oscillator1,2
XTALI Oscillator2,4
fckil
fxtal
—
—
32.7683/32.0
24
—
—
kHz
MHz
1
External oscillator or a crystal with internal oscillator amplifier.
2
The required frequency stability of this clock source is application dependent. For recommendations, see the Hardware
Development Guide for i.MX RT1015 Crossover Processors (IMXRT1015HDG).
3
4
Recommended nominal frequency 32.768 kHz.
External oscillator or a fundamental frequency crystal with internal oscillator amplifier.
The typical values shown in Table 10 are required for use with NXP SDK to ensure precise time keeping
and USB operation. For RTC_XTALI operation, two clock sources are available.
•
On-chip 40 kHz ring oscillator—this clock source has the following characteristics:
— Approximately 25 µA more Idd than crystal oscillator
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
17
Electrical characteristics
— Approximately ±50% tolerance
— No external component required
— Starts up quicker than 32 kHz crystal oscillator
External crystal oscillator with on-chip support circuit:
•
— At power up, ring oscillator is utilized. After crystal oscillator is stable, the clock circuit
switches over to the crystal oscillator automatically.
— Higher accuracy than ring oscillator
— If no external crystal is present, then the ring oscillator is utilized
The decision of choosing a clock source should be taken based on real-time clock use and precision
time-out.
4.1.5
Maximum supply currents
The data shown in Table 11 represent a use case designed specifically to show the maximum current
consumption possible. All cores are running at the defined maximum frequency and are limited to L1
cache accesses only to ensure no pipeline stalls. Although a valid condition, it would have a very limited
practical use case, if at all, and be limited to an extremely low duty cycle unless the intention was to
specifically show the worst case power consumption.
See the i.MX RT1015 Power Consumption Measurement Application Note for more details on typical
power consumption under various use case definitions.
Table 11. Maximum supply currents
Power Rail
Conditions
Max Current
Unit
DCDC_IN
Max power for chip at 95 oC with core 90
mark run on FlexRAM
mA
VDD_HIGH_IN
VDD_SNVS_IN
Include internal loading in analog
—
50
mA
A
250
25
USB_OTG1_VBUS
VDDA_ADC_3P3
25 mA for each active USB interface
mA
mA
3.3 V power supply for 12-bit ADC, 600 40
A typical, 750 A max, for each ADC.
100 Ohm max loading for touch panel,
cause 33 mA current.
NVCC_GPIO
Imax = N x C x V x (0.5 x F)
Where:
N—Number of IO pins supplied by the power line
C—Equivalent external capacitive load
V—IO voltage
(0.5 x F)—Data change rate. Up to 0.5 of the clock rate (F).
In this equation, Imax is in Amps, C in Farads, V in Volts, and F in Hertz.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
18
Electrical characteristics
4.1.6
Low power mode supply currents
Table 12 shows the current core consumption (not including I/O) of i.MX RT1015 processors in selected
low power modes.
Table 12. Low power mode current and power consumption
Mode
Test Conditions
Supply
Typical1
Units
mA
SYSTEM IDLE
• LDO_ARM and LDO_SOC set to the Bypass
mode
• LDO_2P5 set to 2.5 V, LDO_1P1 set to 1.1 V
• CPU in WFI, CPU clock gated
• 24 MHz XTAL is ON
• System PLL is active, other PLLs are power down
• Peripheral clock gated, but remain powered
DCDC_IN (3.3 V)
VDD_HIGH_IN (3.3 V)
VDD_SNVS_IN (3.3 V)
Total
3.82
5.93
0.025
32.258
mW
mA
LOW POWER IDLE
• LDO_SOC is in the Bypass mode, LDO_ARM is DCDC_IN (3.3 V)
in the PG mode
• LDO_2P5 and LDO_1P1 are set to Weak mode
• CPU in Power Gate mode
• All PLLs are power down
• 24 MHz XTAL is off, 24 MHz RCOSC used as
clock source
• Peripheral are powered off
1.13
0.287
0.046
4.828
VDD_HIGH_IN (3.3 V)
VDD_SNVS_IN (3.3 V)
Total
mW
mA
SUSPEND
(DSM)
• LDO_SOC is in the Bypass mode, LDO_ARM is DCDC_IN (3.3 V)
in the PG mode
• LDO_2P5 and LDO_1P1 are shut off
0.19
0.09
VDD_HIGH_IN (3.3 V)
• CPU in Power Gate mode
• All PLLs are power down
• 24 MHz XTAL is off, 24 MHz RCOSC is off
• All clocks are shut off, except 32 kHz RTC
• Peripheral are powered off
VDD_SNVS_IN (3.3 V)
0.018
1.019
Total
mW
mA
SNVS (RTC)
• All SOC digital logic, analog module are shut off DCDC_IN (0 V)
0
• 32 kHz RTC is alive
VDD_HIGH_IN (0 V)
0
VDD_SNVS_IN (3.3 V)
Total
0.018
0.059
mW
1
The typical values shown here are for information only and are not guaranteed. These values are average values measured
on a typical process wafer at 25oC.
4.1.7
USB PHY current consumption
Power down mode
4.1.7.1
In power down mode, everything is powered down, including the USB VBUS valid detectors in typical
condition. Table 13 shows the USB interface current consumption in power down mode.
Table 13. USB PHY current consumption in power down mode
VDD_USB_CAP (3.0 V)
5.1 A
VDD_HIGH_CAP (2.5 V)
1.7 A
NVCC_PLL (1.1 V)
< 0.5 A
Current
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
19
Electrical characteristics
NOTE
The currents on the VDD_HIGH_CAP and VDD_USB_CAP were
identified to be the voltage divider circuits in the USB-specific level
shifters.
4.2
System power and clocks
This section provide the information about the system power and clocks.
4.2.1
Power supplies requirements and restrictions
The system design must comply with power-up sequence, power-down sequence, and steady state
guidelines as described in this section to guarantee the reliable operation of the device. Any deviation
from these sequences may result in the following situations:
•
•
•
Excessive current during power-up phase
Prevention of the device from booting
Irreversible damage to the processor (worst-case scenario)
4.2.1.1
Power-up sequence
The below restrictions must be followed:
•
•
•
•
•
VDD_SNVS_IN supply must be turned on before any other power supply or be connected
(shorted) with VDD_HIGH_IN supply.
If a coin cell is used to power VDD_SNVS_IN, then ensure that it is connected before any other
supply is switched on.
When internal DCDC is enabled, external delay circuit is required to delay the
“DCDC_PSWITCH” signal 1 ms after DCDC_IN is stable.
Need to ensure DCDC_IN ramps to 3.0 V within 0.2 x RC, RC is from external delay circuit used
for DCDC_PSWITCH and RC must be longer than 1 ms.
POR_B should be held low during the entire power up sequence.
NOTE
The POR_B input (if used) must be immediately asserted at power-up and
remain asserted until after the last power rail reaches its working voltage. In
the absence of an external reset feeding the POR_B input, the internal POR
module takes control. See the i.MX RT1015 Reference Manual
(IMXRT1015RM) for further details and to ensure that all necessary
requirements are being met.
NOTE
Need to ensure that there is no back voltage (leakage) from any supply on
the board towards the 3.3 V supply (for example, from the external
components that use both the 1.8 V and 3.3 V supplies).
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
20
NXP Semiconductors
Electrical characteristics
NOTE
USB_OTG1_VBUS and VDDA_ADC_3P3 are not part of the power
supply sequence and may be powered at any time.
4.2.1.2
Power-down sequence
The following restrictions must be followed:
•
VDD_SNVS_IN supply must be turned off after any other power supply or be connected (shorted)
with VDD_HIGH_IN supply.
•
If a coin cell is used to power VDD_SNVS_IN, then ensure that it is removed after any other supply
is switched off.
4.2.1.3
Power supplies usage
All I/O pins should not be externally driven while the I/O power supply for the pin (NVCC_xxx) is OFF.
This can cause internal latch-up and malfunctions due to reverse current flows. For information about I/O
power supply of each pin, see “Power Rail” columns in pin list tables of Section 6, Package information
and contact assignments.”
4.2.2
Integrated LDO voltage regulator parameters
Various internal supplies can be powered ON from internal LDO voltage regulators. All the supply pins
named *_CAP must be connected to external capacitors. The on-board LDOs are intended for internal use
only and should not be used to power any external circuitry. See the i.MX RT1015 Reference Manual
(IMXRT1015RM) for details on the power tree scheme.
NOTE
The *_CAP signals should not be powered externally. These signals are
intended for internal LDO operation only.
4.2.2.1
Digital regulators (LDO_SNVS)
There are one digital LDO regulator (“Digital”, because of the logic loads that they drive, not because of
their construction). The advantages of the regulator is to reduce the input supply variation because of its
input supply ripple rejection and its on-die trimming. This translates into more stable voltage for the
on-chip logics.
The regulator has two basic modes:
•
Power Gate. The regulation FET is switched fully off limiting the current draw from the supply.
The analog part of the regulator is powered down here limiting the power consumption.
•
Analog regulation mode. The regulation FET is controlled such that the output voltage of the
regulator equals the programmed target voltage. The target voltage is fully programmable in 25 mV
steps.
For additional information, see the i.MX RT1015 Reference Manual (IMXRT1015RM).
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
21
Electrical characteristics
4.2.2.2
Regulators for analog modules
LDO_1P1
4.2.2.2.1
The LDO_1P1 regulator implements a programmable linear-regulator function from VDD_HIGH_IN (see
Table 9 for minimum and maximum input requirements). Typical Programming Operating Range is 1.0 V
to 1.2 V with the nominal default setting as 1.1 V. The LDO_1P1 supplies the USB Phy, and PLLs. A
programmable brown-out detector is included in the regulator that can be used by the system to determine
when the load capability of the regulator is being exceeded to take the necessary steps. Current-limiting
can be enabled to allow for in-rush current requirements during start-up, if needed. Active-pull-down can
also be enabled for systems requiring this feature.
For information on external capacitor requirements for this regulator, see the Hardware Development
Guide for i.MX RT1015 Crossover Processors (IMXRT1015HDG).
For additional information, see the i.MX RT1015 Reference Manual (IMXRT1015RM).
4.2.2.2.2
LDO_2P5
The LDO_2P5 module implements a programmable linear-regulator function from VDD_HIGH_IN (see
Table 9 for minimum and maximum input requirements). Typical Programming Operating Range is 2.25 V
to 2.75 V with the nominal default setting as 2.5 V. LDO_2P5 supplies the USB PHY, E-fuse module, and
PLLs. A programmable brown-out detector is included in the regulator that can be used by the system to
determine when the load capability of the regulator is being exceeded, to take the necessary steps.
Current-limiting can be enabled to allow for in-rush current requirements during start-up, if needed.
Active-pull-down can also be enabled for systems requiring this feature. An alternate self-biased
low-precision weak-regulator is included that can be enabled for applications needing to keep the output
voltage alive during low-power modes where the main regulator driver and its associated global bandgap
reference module are disabled. The output of the weak-regulator is not programmable and is a function of
the input supply as well as the load current. Typically, with a 3 V input supply the weak-regulator output
is 2.525 V and its output impedance is approximately 40 .
For information on external capacitor requirements for this regulator, see the Hardware Development
Guide for i.MX RT1015 Crossover Processors (IMXRT1015HDG).
For additional information, see the i.MX RT1015 Reference Manual (IMXRT1015RM).
4.2.2.2.3
LDO_USB
The LDO_USB module implements a programmable linear-regulator function from the USB VUSB
voltages (4.4 V–5.5 V) to produce a nominal 3.0 V output voltage. A programmable brown-out detector
is included in the regulator that can be used by the system to determine when the load capability of the
regulator is being exceeded, to take the necessary steps. This regulator has a built in power-mux that allows
the user to select to run the regulator from USB VBUS supply. Current limit is also included to help the
system meet in-rush current targets.
For information on external capacitor requirements for this regulator, see the Hardware Development
Guide for i.MX RT1015 Crossover Processors (IMXRT1015HDG).
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
22
NXP Semiconductors
Electrical characteristics
For additional information, see the i.MX RT1015 Reference Manual (IMXRT1015RM).
4.2.2.2.4 DCDC
DCDC can be configured to operate on power-save mode when the load current is less than 50 mA. During
the power-save mode, the converter operates with reduced switching frequency in PFM mode and with a
minimum quiescent current to maintain high efficiency.
DCDC can detect the peak current in the P-channel switch. When the peak current exceeds the threshold,
DCDC will give an alert signal, and the threshold can be configured. By this way, DCDC can roughly
detect the current loading.
DCDC also includes the following protection functions:
•
Over current protection. In run mode, DCDC shuts down when detecting abnormal large current in
the P-type power switch. In power save mode, DCDC stop charging inductor when detecting large
current in the P-type power switch. The threshold is also different in run mode and in power save
mode: the former is 1 A–2A, and the latter is 200 mA–250 mA.
•
•
Over voltage protection. DCDC shuts down when detecting the output voltage is too high.
Low voltage detection. DCDC shuts down when detecting the input voltage is too low.
For additional information, see the i.MX RT1015 Reference Manual (IMXRT1015RM).
4.2.3
PLL’s electrical characteristics
This section provides PLL electrical characteristics.
4.2.3.1
Audio/Video PLL’s electrical parameters
Table 14. Audio/video PLL’s electrical parameters
Parameter Value
Clock output range
Reference clock
Lock time
650 MHz–1.3 GHz
24 MHz
< 11250 reference cycles
4.2.3.2
System PLL
Table 15. System PLL’s electrical parameters
Parameter
Value
Clock output range
Reference clock
Lock time
528 MHz PLL output
24 MHz
< 11250 reference cycles
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
23
Electrical characteristics
4.2.3.3
Ethernet PLL
Table 16. Ethernet PLL’s electrical parameters
Parameter
Value
Clock output range
Reference clock
Lock time
1 GHz
24 MHz
< 11250 reference cycles
4.2.3.4
USB PLL
Table 17. USB PLL’s electrical parameters
Parameter
Value
Clock output range
Reference clock
Lock time
480 MHz PLL output
24 MHz
< 383 reference cycles
4.2.4
On-chip oscillators
OSC24M
4.2.4.1
This block implements an amplifier that when combined with a suitable quartz crystal and external load
capacitors implement an oscillator. The oscillator is powered from NVCC_PLL.
The system crystal oscillator consists of a Pierce-type structure running off the digital supply. A straight
forward biased-inverter implementation is used.
4.2.4.2
OSC32K
This block implements an amplifier that when combined with a suitable quartz crystal and external load
capacitors implement a low power oscillator. It also implements a power mux such that it can be powered
from either a ~3 V backup battery (VDD_SNVS_IN) or VDD_HIGH_IN such as the oscillator consumes
power from VDD_HIGH_IN when that supply is available and transitions to the backup battery when
VDD_HIGH_IN is lost.
In addition, if the clock monitor determines that the OSC32K is not present, then the source of the 32 K
will automatically switch to a crude internal ring oscillator. The frequency range of this block is
approximately 10–45 kHz. It highly depends on the process, voltage, and temperature.
The OSC32k runs from VDD_SNVS_CAP supply, which comes from the
VDD_HIGH_IN/VDD_SNVS_IN. The target battery is a ~3 V coin cell. Proper choice of coin cell type
is necessary for chosen VDD_HIGH_IN range. Appropriate series resistor (Rs) must be used when
connecting the coin cell. Rs depends on the charge current limit that depends on the chosen coin cell. For
example, for Panasonic ML621:
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
24
NXP Semiconductors
Electrical characteristics
•
•
Average Discharge Voltage is 2.5 V
Maximum Charge Current is 0.6 mA
For a charge voltage of 3.2 V, Rs = (3.2-2.5)/0.6 m = 1.17 k.
Table 18. OSC32K main characteristics
Min
Typ
Max Comments
Fosc
—
32.768 KHz
—
This frequency is nominal and determined mainly by the crystal selected.
32.0 K would work as well.
Current consumption
—
4 A
—
The 4 A is the consumption of the oscillator alone (OSC32k). Total supply
consumption will depend on what the digital portion of the RTC consumes.
The ring oscillator consumes 1 A when ring oscillator is inactive, 20 A
when the ring oscillator is running. Another 1.5 A is drawn from vdd_rtc in
the power_detect block. So, the total current is 6.5 A on vdd_rtc when the
ring oscillator is not running.
Bias resistor
—
14 M
—
This integrated bias resistor sets the amplifier into a high gain state. Any
leakage through the ESD network, external board leakage, or even a
scope probe that is significant relative to this value will debias the amp. The
debiasing will result in low gain, and will impact the circuit's ability to start
up and maintain oscillations.
Crystal Properties
Cload
—
—
10 pF
—
Usually crystals can be purchased tuned for different Cloads. This Cload
value is typically 1/2 of the capacitances realized on the PCB on either side
of the quartz. A higher Cload will decrease oscillation margin, but
increases current oscillating through the crystal.
ESR
50 k
100 k Equivalent series resistance of the crystal. Choosing a crystal with a higher
value will decrease the oscillating margin.
4.3
I/O parameters
This section provide parameters on I/O interfaces.
4.3.1
I/O DC parameters
This section includes the DC parameters of the following I/O types:
•
•
XTALI and RTC_XTALI (Clock Inputs) DC Parameters
General Purpose I/O (GPIO)
NOTE
The term ‘NVCC_XXXX’in this section refers to the associated supply rail
of an input or output.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
25
Electrical characteristics
Figure 3. Circuit for parameters Voh and Vol for I/O cells
4.3.1.1
XTALI and RTC_XTALI (clock inputs) DC parameters
Table 19 shows the DC parameters for the clock inputs.
1
Table 19. XTALI and RTC_XTALI DC parameters
Symbol Test Conditions Min
Parameter
Max
Unit
XTALI high-level DC input voltage
XTALI low-level DC input voltage
Vih
Vil
—
—
—
—
0.8 x NVCC_PLL
NVCC_PLL
V
V
V
V
0
0.2
1.1
0.2
RTC_XTALI high-level DC input voltage
RTC_XTALI low-level DC input voltage
Vih
Vil
0.8
0
1
The DC parameters are for external clock input only.
4.3.1.2
Single voltage general purpose I/O (GPIO) DC parameters
Table 20 shows DC parameters for GPIO pads. The parameters in Table 20 are guaranteed per the
operating ranges in Table 9, unless otherwise noted.
Table 20. Single voltage GPIO DC parameters
Parameter
Symbol
VOH
Test Conditions
Min
Max
Units
High-level output voltage1
Ioh = -0.1 mA (ipp_dse =
001,010)
NVCC_XXXX -
0.2
–
V
Ioh= -1 mA
(ipp_dse = 011,100,101,110,111)
Low-level output voltage1
VOL
Iol = 0.1 mA (ipp_dse = 001,010) –
Iol= 1 mA
0.2
V
(ipp_dse = 011,100,101,110,111)
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
26
Electrical characteristics
Table 20. Single voltage GPIO DC parameters (continued)
Parameter
Symbol
Test Conditions
Min
Max
Units
High-level output current
IOH
VDDE = 3.3 V, VOH = VDDE - 0.45
—
mA
V, ipp_dse as follows:
001
010
011
110
101
110
111
-1
-1
-2
-2
-2
-4
-4
Low-level output current
IOL
VDDE = 3.3 V, VOL = 0.45 V,
—
mA
ipp_dse as follows:
001
010
011
110
101
110
111
1
1
2
2
2
4
4
High-Level input voltage1,2
Low-Level input voltage1,2
VIH
—
—
0.7 x
NVCC_XXXX
NVCC_XXXX
V
VIL
0
0.3 x
V
NVCC_XXXX
Input Hysteresis
(NVCC_XXXX= 1.8V)
VHYS_LowV NVCC_XXXX = 1.8 V
DD
250
250
—
—
—
mV
mV
mV
mV
Input Hysteresis
(NVCC_XXXX=3.3V)
VHYS_High NVCC_XXXX = 3.3 V
VDD
Schmitt trigger VT+2,3
Schmitt trigger VT-2,3
VTH+
—
0.5 x
NVCC_XXXX
VTH-
—
—
0.5 x
NVCC_XXXX
Pull-up resistor (22_k PU)
Pull-up resistor (22_k PU)
Pull-up resistor (47_k PU)
Pull-up resistor (47_k PU)
Pull-up resistor (100_k PU)
Pull-up resistor (100_k PU)
RPU_22K
RPU_22K
RPU_47K
RPU_47K
Vin = 0 V
—
—
—
—
—
—
—
—
-1
212
1
A
A
A
A
A
A
A
A
A
k
Vin = NVCC_XXXX
Vin = 0 V
100
1
Vin = NVCC_XXXX
RPU_100K Vin = 0 V
48
1
RPU_100K Vin = NVCC_XXXX
Pull-down resistor (100_k PD) RPD_100K Vin = NVCC_XXXX
Pull-down resistor (100_k PD) RPD_100K Vin = 0V
48
1
Input current (no PU/PD)
Keeper Circuit Resistance
IIN
VI = 0, VI = NVCC_XXXX
1
R_Keeper
VI =0.3 x NVCC_XXXX, VI = 0.7 105
x NVCC_XXXX
175
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
27
Electrical characteristics
1
Overshoot and undershoot conditions (transitions above NVCC_XXXX and below GND) on switching pads must be held
below 0.6 V, and the duration of the overshoot/undershoot must not exceed 10% of the system clock cycle. Overshoot/
undershoot must be controlled through printed circuit board layout, transmission line impedance matching, signal line
termination, or other methods. Non-compliance to this specification may affect device reliability or cause permanent damage
to the device.
2
To maintain a valid level, the transition edge of the input must sustain a constant slew rate (monotonic) from the current DC
level through to the target DC level, Vil or Vih. Monotonic input transition time is from 0.1 ns to 1 s.
3
Hysteresis of 250 mV is guaranteed over all operating conditions when hysteresis is enabled.
4.3.2
I/O AC parameters
This section includes the AC parameters of the following I/O types:
General Purpose I/O (GPIO)
Figure 4 shows load circuit for output, and Figure 5 show the output transition time waveform.
•
From Output
Under Test
Test Point
CL
CL includes package, probe and fixture capacitance
Figure 4. Load circuit for output
OVDD
0 V
80%
20%
80%
20%
tr
Output (at pad)
tf
Figure 5. Output transition time waveform
4.3.2.1
General purpose I/O AC parameters
The I/O AC parameters for GPIO in slow and fast modes are presented in the Table 21 and Table 22,
respectively. Note that the fast or slow I/O behavior is determined by the appropriate control bits in the
IOMUXC control registers.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
28
NXP Semiconductors
Electrical characteristics
Table 21. General purpose I/O AC parameters 1.8 V mode
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Output Pad Transition Times, rise/fall
(Max Drive, ipp_dse=111)
tr, tf
15 pF Cload, slow slew rate
15 pF Cload, fast slew rate
2.72/2.79
1.51/1.54
—
—
Output Pad Transition Times, rise/fall
(High Drive, ipp_dse=101)
tr, tf
tr, tf
tr, tf
trm
15 pF Cload, slow slew rate
15 pF Cload, fast slew rate
3.20/3.36
1.96/2.07
—
—
—
—
ns
ns
Output Pad Transition Times, rise/fall
(Medium Drive, ipp_dse=100)
15 pF Cload, slow slew rate
15 pF Cload, fast slew rate
3.64/3.88
2.27/2.53
Output Pad Transition Times, rise/fall
(Low Drive. ipp_dse=011)
15 pF Cload, slow slew rate
15 pF Cload, fast slew rate
4.32/4.50
3.16/3.17
—
—
—
—
Input Transition Times1
—
25
1
Hysteresis mode is recommended for inputs with transition times greater than 25 ns.
Table 22. General purpose I/O AC parameters 3.3 V mode
Parameter
Symbol
Test condition
Min
Typ
Max
Unit
Output Pad Transition Times, rise/fall tr, tf
(Max Drive, ipp_dse=101)
15 pF Cload, slow slew rate
15 pF Cload, fast slew rate
1.70/1.79
1.06/1.15
—
—
Output Pad Transition Times, rise/fall tr, tf
(High Drive, ipp_dse=011)
15 pF Cload, slow slew rate
15 pF Cload, fast slew rate
2.35/2.43
1.74/1.77
—
—
—
—
ns
Output Pad Transition Times, rise/fall tr, tf
(Medium Drive, ipp_dse=010)
15 pF Cload, slow slew rate
15 pF Cload, fast slew rate
3.13/3.29
2.46/2.60
Output Pad Transition Times, rise/fall tr, tf
(Low Drive. ipp_dse=001)
15 pF Cload, slow slew rate
15 pF Cload, fast slew rate
5.14/5.57
4.77/5.15
—
—
—
—
ns
ns
Input Transition Times1
trm
—
25
1
Hysteresis mode is recommended for inputs with transition times greater than 25 ns.
4.3.3
Output buffer impedance parameters
This section defines the I/O impedance parameters of the i.MX RT1015 processors for the following I/O
types:
•
Single Voltage General Purpose I/O (GPIO)
NOTE
GPIO I/O output driver impedance is measured with “long” transmission
line of impedance Ztl attached to I/O pad and incident wave launched into
transmission line. Rpu/Rpd and Ztl form a voltage divider that defines
specific voltage of incident wave relative to NVCC_XXXX. Output driver
impedance is calculated from this voltage divider (see Figure 6).
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
29
Electrical characteristics
OVDD
PMOS (Rpu)
Ztl , L = 20 inches
ipp_do
pad
predriver
Cload = 1p
NMOS (Rpd)
OVSS
U,(V)
(do)
Vin
VDD
t,(ns)
0
OVDD
Vref
U,(V)
Vout (pad)
Vref2
Vref1
t,(ns)
0
Vovdd - Vref1
Vref1
Vref2
Vovdd - Vref2
Rpu =
Ztl
Rpd =
Ztl
Figure 6. Impedance matching load for measurement
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
30
Electrical characteristics
4.3.3.1
Single voltage GPIO output buffer impedance
Table 23 shows the GPIO output buffer impedance (NVCC_XXXX 1.8 V).
Table 23. GPIO output buffer average impedance (NVCC_XXXX 1.8 V)
Symbol Drive strength (DSE) Typ value
Parameter
Unit
001
010
011
100
101
110
111
260
130
88
65
52
Output Driver
Impedance
Rdrv
43
37
Table 24 shows the GPIO output buffer impedance (NVCC_XXXX 3.3 V).
Table 24. GPIO Output buffer average impedance (NVCC_XXXX 3.3 V)
Parameter
Symbol Drive strength (DSE) Typ value
Unit
001
010
011
100
101
110
111
157
78
53
39
32
26
23
Output Driver
Impedance
Rdrv
4.4
System modules
This section contains the timing and electrical parameters for the modules in the i.MX RT1015 processor.
4.4.1
Reset timings parameters
Figure 7 shows the reset timing and Table 25 lists the timing parameters.
POR_B
(Input)
CC1
Figure 7. Reset timing diagram
Table 25. Reset timing parameters
ID
CC1
Parameter
Min Max
Unit
Duration of POR_B to be qualified as valid.
1
—
RTC_XTALI cycle
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
31
Electrical characteristics
4.4.2
WDOG reset timing parameters
Figure 8 shows the WDOG reset timing and Table 26 lists the timing parameters.
WDOGn_B
(Output)
CC3
Figure 8. WDOGn_B timing diagram
Table 26. WDOGn_B timing parameters
ID
CC3
Parameter
Duration of WDOGn_B Assertion
Min
Max
Unit
1
—
RTC_XTALI cycle
NOTE
RTC_XTALI is approximately 32 kHz. RTC_XTALI cycle is one period or
approximately 30 s.
NOTE
WDOGn_B output signals (for each one of the Watchdog modules) do not
have dedicated pins, but are muxed out through the IOMUX. See the IOMUX
manual for detailed information.
4.4.3
SCAN JTAG Controller (SJC) timing parameters
Figure 9 depicts the SJC test clock input timing. Figure 10 depicts the SJC boundary scan timing.
Figure 11 depicts the SJC test access port. Signal parameters are listed in Table 27.
SJ1
SJ2
SJ2
JTAG_TCK
(Input)
VM
VM
VIH
VIL
SJ3
SJ3
Figure 9. Test clock input timing diagram
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
32
Electrical characteristics
JTAG_TCK
(Input)
VIH
SJ5
VIL
SJ4
Input Data Valid
Data
Inputs
SJ6
Data
Outputs
Output Data Valid
SJ7
SJ6
Data
Outputs
Data
Outputs
Output Data Valid
Figure 10. Boundary scan (JTAG) timing diagram
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
33
Electrical characteristics
JTAG_TCK
(Input)
VIH
SJ9
VIL
SJ8
Input Data Valid
JTAG_TDI
JTAG_TMS
(Input)
SJ10
SJ11
SJ10
JTAG_TDO
(Output)
Output Data Valid
JTAG_TDO
(Output)
JTAG_TDO
(Output)
Output Data Valid
Figure 11. Test access port timing diagram
JTAG_TCK
(Input)
SJ13
JTAG_TRST_B
(Input)
SJ12
Figure 12. JTAG_TRST_B timing diagram
Table 27. JTAG timing
All frequencies
Min Max
ID
Parameter1,2
Unit
1
SJ0
JTAG_TCK frequency of operation 1/(3•TDC
)
0.001
45
22.5
—
22
—
—
3
MHz
SJ1
SJ2
SJ3
SJ4
SJ5
SJ6
SJ7
SJ8
JTAG_TCK cycle time in crystal mode
ns
ns
ns
ns
ns
ns
ns
ns
2
JTAG_TCK clock pulse width measured at VM
JTAG_TCK rise and fall times
Boundary scan input data set-up time
Boundary scan input data hold time
JTAG_TCK low to output data valid
JTAG_TCK low to output high impedance
JTAG_TMS, JTAG_TDI data set-up time
5
—
—
40
40
—
24
—
—
5
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
34
Electrical characteristics
Table 27. JTAG timing (continued)
Parameter1,2
All frequencies
Min Max
ID
Unit
SJ9
JTAG_TMS, JTAG_TDI data hold time
JTAG_TCK low to JTAG_TDO data valid
JTAG_TCK low to JTAG_TDO high impedance
JTAG_TRST_B assert time
25
—
—
44
44
—
—
ns
SJ10
SJ11
SJ12
SJ13
ns
ns
ns
ns
—
100
40
JTAG_TRST_B set-up time to JTAG_TCK low
= target frequency of SJC
1
T
DC
2
VM = mid-point voltage
4.4.4
Debug trace timing specifications
Table 28. Debug trace operating behaviors
Symbol
Description
Min
Max
Unit
T1
T2
T3
T4
T5
T6
T7
T8
ARM_TRACE_CLK frequency of operation
ARM_TRACE_CLK period
Low pulse width
—
1/T1
6
70
—
—
—
1
MHz
MHz
ns
High pulse width
6
ns
Clock and data rise time
Clock and data fall time
Data setup
—
—
2
ns
1
ns
—
—
ns
Data hold
0.7
ns
!2-?42!#%?#,+
4ꢀ
T6
T4
4ꢂ
4ꢁ
Figure 13. ARM_TRACE_CLK specifications
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
35
Electrical characteristics
ARM_TRACE_CLK
ARM_TRACE0-3
T7
T8
T7
T8
Figure 14. Trace data specifications
4.5
External memory interface
The following sections provide information about external memory interfaces.FlexSPI parameters
Measurements are with a load 15 pf and input slew rate of 1 V/ns.
4.5.1
FlexSPI input/read timing
There are four sources for the internal sample clock for FlexSPI read data:
• Dummy read strobe generated by FlexSPI controller and looped back internally
(FlexSPIn_MCR0[RXCLKSRC] = 0x0)
• Dummy read strobe generated by FlexSPI controller and looped back through the
DQS pad (FlexSPIn_MCR0[RXCLKSRC] = 0x1)
• Read strobe provided by memory device and input from DQS pad
(FlexSPIn_MCR0[RXCLKSRC] = 0x3)
The following sections describe input signal timing for each of these four internal sample clock sources.
4.5.1.0.1
SDR mode with FlexSPIn_MCR0[RXCLKSRC] = 0x0, 0x1
Table 29. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0X0
Symbol
Parameter
Frequency of operation
Min
Max
Unit
—
—
8.67
0
60
—
—
MHz
ns
TIS
TIH
Setup time for incoming data
Hold time for incoming data
ns
Table 30. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0X1
Symbol
Parameter
Frequency of operation
Min
Max
Unit
—
—
2
133
—
MHz
ns
TIS
TIH
Setup time for incoming data
Hold time for incoming data
1
—
ns
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
36
Electrical characteristics
SCK
TIS
TIH
TIS
TIH
SIO[0:7]
Internal Sample Clock
Figure 15. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0X0, 0X1
NOTE
Timing shown is based on the memory generating read data on the SCK
falling edge, and FlexSPI controller sampling read data on the falling edge.
4.5.1.0.2
SDR mode with FlexSPIn_MCR0[RXCLKSRC] = 0x3
There are two cases when the memory provides both read data and the read strobe in SDR mode:
• A1–Memory generates both read data and read strobe on SCK rising edge (or falling
edge)
• A2–Memory generates read data on SCK falling edge and generates read strobe on
SCK rising edgeSCK rising edge
Table 31. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3 (Case A1)
Value
Symbol
Parameter
Unit
Min
Max
—
Frequency of operation
—
—
—
-2
166
—
—
2
MHz
ns
TSCKD
Time from SCK to data valid
Time from SCK to DQS
TSCKDQS
ns
TSCKD - TSCKDQS
Time delta between TSCKD and TSCKDQS
ns
SCK
TSCKD
TSCKD
SIO[0:7]
TSCKDQS
TSCKDQS
DQS
Figure 16. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0X3 (Case A1)
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
37
Electrical characteristics
NOTE
Timing shown is based on the memory generating read data and read strobe
on the SCK rising edge. The FlexSPI controller samples read data on the
DQS falling edge.
Table 32. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3 (Case A2)
Value
Symbol
Parameter
Unit
Min
Max
—
Frequency of operation
—
—
—
-2
166
—
—
2
MHz
ns
TSCKD
Time from SCK to data valid
Time from SCK to DQS
TSCKDQS
ns
TSCKD - TSCKDQS
Time delta between TSCKD and TSCKDQS
ns
SCK
TSCKD
TSCKD
TSCKD
SIO[0:7]
TSCKDQS
TSCKDQS
TSCKDQS
DQS
Internal Sample Clock
Figure 17. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0X3 (Case A2)
NOTE
Timing shown is based on the memory generating read data on the SCK
falling edge and read strobe on the SCK rising edge. The FlexSPI controller
samples read data on a half cycle delayed DQS falling edge.
4.5.1.0.3
DDR mode with FlexSPIn_MCR0[RXCLKSRC] = 0x0, 0x1
Table 33. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x0
Symbol
Parameter
Frequency of operation
Min
Max
Unit
—
—
8.67
0
30
—
—
MHz
ns
TIS
TIH
Setup time for incoming data
Hold time for incoming data
ns
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
38
Electrical characteristics
Table 34. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x1
Symbol
Parameter
Frequency of operation
Min
Max
Unit
—
—
2
66
—
—
MHz
ns
TIS
TIH
Setup time for incoming data
Hold time for incoming data
1
ns
SCLK
TIS
TIH
TIS
TIH
SIO[0:7]
Internal Sample Clock
Figure 18. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x0, 0x1
4.5.1.0.4
DDR mode with FlexSPIn_MCR0[RXCLKSRC] = 0x3
There are two cases when the memory provides both read data and the read strobe in DDR mode:
• B1–Memory generates both read data and read strobe on SCK edge
• B2–Memory generates read data on SCK edge and generates read strobe on SCK2
edge
Table 35. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3 (Case B1)
Symbol
Parameter
Frequency of operation
Min
Max
Unit
—
—
—
—
-1
166
—
—
1
MHz
ns
TSCKD
Time from SCK to data valid
Time from SCK to DQS
TSCKDQS
ns
TSCKD - TSCKDQS
Time delta between TSCKD and TSCKDQS
ns
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
39
Electrical characteristics
SCK
TSCKD
SIO[0:7]
TSCKDQS
DQS
Figure 19. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3 (Case B1)
Table 36. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3 (Case B2)
Symbol
Parameter
Frequency of operation
Min
Max
Unit
—
—
—
-1
166
—
1
MHz
ns
TSCKD
Time from SCK to data valid
TSCKD - TSCKDQS
Time delta between TSCKD and TSCKDQS
ns
SCK
SIO[0:7]
SCK2
TSCKD
TSCK2DQS
DQS
Figure 20. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3 (Case B2)
4.5.1.1
FlexSPI output/write timing
The following sections describe output signal timing for the FlexSPI controller including control signals
and data outputs.
4.5.1.1.1
SDR mode
Table 37. FlexSPI output timing in SDR mode
Symbol
Parameter
Min
Max
Unit
—
Frequency of operation
SCK clock period
—
6.0
—
1661
—
MHz
ns
Tck
TDVO
TDHO
Output data valid time
Output data hold time
1
ns
-1
—
ns
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
40
Electrical characteristics
Table 37. FlexSPI output timing in SDR mode (continued)
Symbol
Parameter
Min
Max
Unit
TCSS
TCSH
Chip select output setup time
Chip select output hold time
3 x TCK -1
—
—
ns
ns
3 x TCK + 2
1
The actual maximum frequency supported is limited by the FlexSPIn_MCR0[RXCLKSRC] configuration used. Please refer to the FlexSPI SDR input timing
specifications.
NOTE
TCSS and TCSH are configured by the FlexSPIn_FLSHAxCR1
register, the default values are shown above. Please refer to the i.MX
RT1015 Reference Manual (IMXRT1015RM) for more details.
SCK
TCSH
T
CSS
T
CK
CS
TDVO
TDVO
SIO[0:7]
TDHO
TDHO
Figure 21. FlexSPI output timing in SDR mode
4.5.1.1.2
DDR mode
Table 38. FlexSPI output timing in DDR mode
Symbol
Parameter
Min
Max
Unit
—
Frequency of operation1
—
166
—
MHz
ns
Tck
SCK clock period (FlexSPIn_MCR0[RXCLKSRC] = 0x0)
Output data valid time
6.0
—
TDVO
TDHO
TCSS
TCSH
2.2
—
ns
Output data hold time
0.8
ns
Chip select output setup time
Chip select output hold time
3 x TCK / 2 - 0.7
3 x TCK / 2 + 0.8
—
ns
—
ns
1
The actual maximum frequency supported is limited by the FlexSPIn_MCR0[RXCLKSRC] configuration used. Please refer to the FlexSPI SDR input timing
specifications.
NOTE
TCSS and TCSH are configured by the FlexSPIn_FLSHAxCR1
register, the default values are shown above. Please refer to the i.MX
RT1015 Reference Manual (IMXRT1015RM) for more details.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
41
Electrical characteristics
SCK
T
CSS
T
CK
TCSH
CS
TDVO
TDVO
SIO[0:7]
TDHO
TDHO
Figure 22. FlexSPI output timing in DDR mode
4.6
Audio
This section provide information about SAI/I2S and SPDIF.
4.6.1
SAI/I2S switching specifications
This section provides the AC timings for the SAI in master (clocks driven) and slave (clocks input) modes.
All timings are given for non-inverted serial clock polarity (SAI_TCR[TSCKP] = 0, SAI_RCR[RSCKP]
= 0) and non-inverted frame sync (SAI_TCR[TFSI] = 0, SAI_RCR[RFSI] = 0). If the polarity of the clock
and/or the frame sync have been inverted, all the timings remain valid by inverting the clock signal
(SAI_BCLK) and/or the frame sync (SAI_FS) shown in the figures below.
Table 39. Master mode SAI timing
Num
Characteristic
SAI_MCLK cycle time
Min
2 x tsys
Max
Unit
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
—
ns
SAI_MCLK pulse width high/low
SAI_BCLK cycle time
40%
4 x tsys
40%
—
60%
—
MCLK period
ns
SAI_BCLK pulse width high/low
SAI_BCLK to SAI_FS output valid
SAI_BCLK to SAI_FS output invalid
SAI_BCLK to SAI_TXD valid
60%
15
BCLK period
ns
ns
ns
ns
ns
ns
0
—
—
15
SAI_BCLK to SAI_TXD invalid
0
—
SAI_RXD/SAI_FS input setup before SAI_BCLK
SAI_RXD/SAI_FS input hold after SAI_BCLK
15
—
0
—
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
42
Electrical characteristics
Figure 23. SAI timing—master modes
Table 40. Slave mode SAI timing
Num
Characteristic
SAI_BCLK cycle time (input)
Min
4 x tsys
Max
Unit
S11
S12
S13
S14
S15
S16
S17
S18
—
ns
SAI_BCLK pulse width high/low (input)
SAI_FS input setup before SAI_BCLK
SAI_FA input hold after SAI_BCLK
40%
10
2
60%
—
BCLK period
ns
ns
ns
ns
ns
ns
—
SAI_BCLK to SAI_TXD/SAI_FS output valid
SAI_BCLK to SAI_TXD/SAI_FS output invalid
SAI_RXD setup before SAI_BCLK
—
0
20
—
10
2
—
SAI_RXD hold after SAI_BCLK
—
Figure 24. SAI timing—slave modes
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
43
Electrical characteristics
4.6.2
SPDIF timing parameters
The Sony/Philips Digital Interconnect Format (SPDIF) data is sent using the bi-phase marking code. When
encoding, the SPDIF data signal is modulated by a clock that is twice the bit rate of the data signal.
Table 41 and Figure 25 and Figure 26 show SPDIF timing parameters for the Sony/Philips Digital
Interconnect Format (SPDIF), including the timing of the modulating Rx clock (SPDIF_SR_CLK) for
SPDIF in Rx mode and the timing of the modulating Tx clock (SPDIF_ST_CLK) for SPDIF in Tx mode.
Table 41. SPDIF timing parameters
Timing parameter range
Characteristics
Symbol
Unit
Min
Max
SPDIF_IN Skew: asynchronous inputs, no specs apply
—
—
0.7
ns
ns
SPDIF_OUT output (Load = 50pf)
• Skew
• Transition rising
• Transition falling
—
—
—
—
—
—
1.5
24.2
31.3
SPDIF_OUT1 output (Load = 30pf)
• Skew
• Transition rising
—
—
—
ns
—
—
—
1.5
13.6
18.0
• Transition falling
Modulating Rx clock (SPDIF_SR_CLK) period
SPDIF_SR_CLK high period
srckp
40.0
16.0
16.0
40.0
16.0
16.0
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
srckph
srckpl
stclkp
stclkph
stclkpl
SPDIF_SR_CLK low period
Modulating Tx clock (SPDIF_ST_CLK) period
SPDIF_ST_CLK high period
SPDIF_ST_CLK low period
srckp
srckpl
srckph
VM
SPDIF_SR_CLK
VM
(Output)
Figure 25. SPDIF_SR_CLK timing diagram
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
44
Electrical characteristics
stclkp
stclkpl
VM
stclkph
VM
SPDIF_ST_CLK
(Input)
Figure 26. SPDIF_ST_CLK timing diagram
4.7
Analog
The following sections provide information about analog interfaces.
4.7.1
DCDC
Table 42 introduces the DCDC electrical specification.
Table 42. DCDC electrical specifications
Buck mode only, one output
3.3 V
Mode
Notes
Input voltage
Output voltage
Max loading
± 10%
1.1 V
Configurable 0.8 ~ 1.575 with 25 mV one step
500 mA
—
Loading in low power modes
Efficiency
200 A ~ 30 mA
90% max
—
@150 mA
Low power mode
Run mode
Open loop mode
Ripple is about 15 mV
Configurable by register
• Always continuous mode
• Support discontinuous mode
Inductor
4.7 H
33 F
1.6 V
—
—
Capacitor
Over voltage protection
Detect VDDSOC, when the voltage is higher
than 1.6 V, shutdown DCDC.
Over Current protection
Low battery detection
1 A
Detect the peak current
• Run mode: when the current is larger than
1 A, shutdown DCDC.
• Stop mode: when the current is larger than
250 mA, stop charging the inductor.
2.6 V
Detect the battery, when battery is lower than
2.6 V, shutdown DCDC.
4.7.2
A/D converter
This section introduces information about A/D converter.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
45
Electrical characteristics
4.7.2.1
12-bit ADC electrical characteristics
The section provide information about 12-bit ADC electrical characteristics.
4.7.2.1.1
12-bit ADC operating conditions
Table 43. 12-bit ADC operating conditions
Typ1
Characteristic
Conditions
Absolute
Symb
Min
Max
Unit
Comment
Supply voltage
VDDA
3.0
-
3.6
V
—
—
Delta to VDD
(VDD-VDDA)2
VDDA
-100
0
100
mV
Ground voltage
Delta to VSS
VSSAD
-100
0
100
mV
—
(VSS-VSSAD)
Ref Voltage High
Ref Voltage Low
Input Voltage
—
VDDA
VSS
1.13
VSS
VSS
—
VDDA
VSS
—
VDDA
VSS
VDDA
2
V
—
—
—
—
—
—
—
—
V
—
VADIN
CADIN
RADIN
V
Input Capacitance
Input Resistance
8/10/12 bit modes
ADLPC=0, ADHSC=1
ADLPC=0, ADHSC=0
ADLPC=1, ADHSC=0
1.5
5
pF
—
7
kohms
kohms
kohms
kohms
—
12.5
25
15
—
30
Analog Source
Resistance
12 bit mode fADCK
40MHz ADLSMP=0,
=
RAS
—
—
1
Tsamp=150
ns
ADSTS=10, ADHSC=1
RAS depends on Sample Time Setting (ADLSMP, ADSTS) and ADC Power Mode (ADHSC, ADLPC). See charts for Minimum
Sample Time vs RAS
ADC Conversion Clock ADLPC=0, ADHSC=1
fADCK
4
4
4
—
—
—
40
30
20
MHz
MHz
MHz
—
—
—
Frequency
12 bit mode
ADLPC=0, ADHSC=0
12 bit mode
ADLPC=1, ADHSC=0
12 bit mode
1
2
Typical values assume VDDAD = 3.0 V, Temp = 25°C, fADCK=20 MHz unless otherwise stated. Typical values are for reference
only and are not tested in production.
DC potential differences
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
46
NXP Semiconductors
Electrical characteristics
Figure 27. 12-bit ADC input impedance equivalency diagram
12-bit ADC characteristics
Table 44. 12-bit ADC characteristics (V
= V
, V
= V
)
SSAD
REFH
DDA
REFL
Characteristic
Conditions1
Symb
IDDA
Min
Typ2
Max
Unit
Comment
Supply Current
ADLPC=1,
ADHSC=0
—
250
350
400
0.01
—
µA
ADLSMP= 0,ADSTS
= 10, ADCO = 1
ADLPC=0,
ADHSC=0
ADLPC=0,
ADHSC=1
Supply Current
Stop, Reset, Module IDDA
Off
—
0.8
µA
—
ADC Asynchronous
Clock Source
ADHSC=0
ADHSC=1
fADACK
—
—
10
20
—
—
MHz
tADACK = 1/fADACK
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
47
Electrical characteristics
Table 44. 12-bit ADC characteristics (V
= V
, V
= V
) (continued)
Unit Comment
REFH
DDA
REFL
SSAD
Characteristic
Conditions1
Symb
Min
Typ2
Max
Sample Cycles
ADLSMP=0,
Csamp
—
2
—
cycles
—
ADSTS=00
ADLSMP=0,
ADSTS=01
4
ADLSMP=0,
ADSTS=10
6
ADLSMP=0,
ADSTS=11
8
ADLSMP=1,
ADSTS=00
12
16
20
24
28
30
32
34
38
42
46
50
ADLSMP=1,
ADSTS=01
ADLSMP=1,
ADSTS=10
ADLSMP=1,
ADSTS=11
Conversion Cycles
ADLSMP=0
ADSTS=00
Cconv
—
—
cycles
—
ADLSMP=0
ADSTS=01
ADLSMP=0
ADSTS=10
ADLSMP=0
ADSTS=11
ADLSMP=1
ADSTS=00
ADLSMP=1
ADSTS=01
ADLSMP=1
ADSTS=10
ADLSMP=1,
ADSTS=11
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
48
Electrical characteristics
) (continued)
Table 44. 12-bit ADC characteristics (V
= V
, V
= V
REFL SSAD
REFH
DDA
Characteristic
Conditions1
Symb
Tconv
Min
Typ2
0.7
Max
Unit
Comment
Conversion Time
ADLSMP=0
—
—
µs
Fadc = 40 MHz
ADSTS=00
ADLSMP=0
ADSTS=01
0.75
0.8
ADLSMP=0
ADSTS=10
ADLSMP=0
ADSTS=11
0.85
0.95
1.05
1.15
1.25
ADLSMP=1
ADSTS=00
ADLSMP=1
ADSTS=01
ADLSMP=1
ADSTS=10
ADLSMP=1,
ADSTS=11
Total Unadjusted
Error
12 bit mode
10 bit mode
8 bit mode
TUE
—
—
—
3.4
1.5
1.2
—
—
—
LSB
1 LSB =
AVGE = 1, AVGS = 11
(VREFH
VREFL)/2
N
-
Differential
Non-Linearity
12 bit mode
10bit mode
8 bit mode
DNL
INL
—
—
—
—
—
—
—
—
—
—
—
—
0.76
0.36
0.14
2.78
0.61
0.14
-1.14
-0.25
-0.19
-1.06
-0.03
-0.02
10.7
—
—
—
—
—
—
—
—
—
—
—
—
—
LSB
LSB
LSB
LSB
AVGE = 1, AVGS = 11
AVGE = 1, AVGS = 11
AVGE = 1, AVGS = 11
AVGE = 1, AVGS = 11
Integral Non-Linearity 12 bit mode
10bit mode
8 bit mode
Zero-Scale Error
Full-Scale Error
12 bit mode
10bit mode
8 bit mode
12 bit mode
10bit mode
8 bit mode
EZS
EFS
Effective Number of 12 bit mode
Bits
ENOB
SINAD
10.1
Bits
dB
AVGE = 1, AVGS = 11
AVGE = 1, AVGS = 11
Signal to Noise plus See ENOB
Distortion
SINAD = 6.02 x ENOB + 1.76
1
All accuracy numbers assume the ADC is calibrated with VREFH=VDDAD
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
49
Electrical characteristics
2
Typical values assume VDDAD = 3.0 V, Temp = 25°C, Fadck=20 MHz unless otherwise stated. Typical values are for reference
only and are not tested in production.
NOTE
The ADC electrical spec is met with the calibration enabled configuration.
Figure 28. Minimum Sample Time Vs Ras (Cas = 2 pF)
Figure 29. Minimum Sample Time Vs Ras (Cas = 5 pF)
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
50
NXP Semiconductors
Electrical characteristics
Figure 30. Minimum Sample Time Vs Ras (Cas = 10 pF)
4.8
Communication interfaces
The following sections provide the information about communication interfaces.
4.8.1
LPSPI timing parameters
The Low Power Serial Peripheral Interface (LPSPI) provides a synchronous serial bus with master and
slave operations. Many of the transfer attributes are programmable. The following tables provide timing
characteristics for classic LPSPI timing modes.
All timing is shown with respect to 20% V and 80% V thresholds, unless noted, as well as input
DD
DD
signal transitions of 3 ns and a 30 pF maximum load on all LPSPI pins.
Table 45. LPSPI Master mode timing
Number
Symbol
Description
Frequency of operation
Min.
Max.
Units
Note
1
1
2
3
4
5
6
7
8
9
fSCK
tSCK
tLead
tLag
tWSCK
tSU
—
fperiph / 2
Hz
ns
2
SCK period
2 x tperiph
—
—
—
—
—
—
8
Enable lead time
1
tperiph
tperiph
ns
—
—
—
—
—
—
—
Enable lag time
1
Clock (SCK) high or low time
Data setup time (inputs)
Data hold time (inputs)
Data valid (after SCK edge)
Data hold time (outputs)
tSCK / 2 - 3
10
2
ns
tHI
ns
tV
—
0
ns
tHO
—
ns
1
2
Absolute maximum frequency of operation (fop) is 30 MHz. The clock driver in the LPSPI module for fperiph must be
guaranteed this limit is not exceeded.
tperiph = 1 / fperiph
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
51
Electrical characteristics
1
PCS
(OUTPUT)
3
2
4
SCK
(CPOL=0)
(OUTPUT)
5
5
SCK
(CPOL=1)
(OUTPUT)
6
7
SIN
(INPUT)
2
LSB IN
BIT 6 . . . 1
MSB IN
8
9
SOUT
(OUTPUT)
2
BIT 6 . . . 1
MSB OUT
LSB OUT
1. If configured as an output.
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure 31. LPSPI Master mode timing (CPHA = 0)
1
PCS
(OUTPUT)
2
4
3
SCK
(CPOL=0)
(OUTPUT)
5
5
7
SCK
(CPOL=1)
(OUTPUT)
6
SIN
(INPUT)
MSB IN2
BIT 6 . . . 1
LSB IN
9
8
MASTER MSB OUT2
SOUT
(OUTPUT)
PORT DATA
BIT 6 . . . 1
PORT DATA
MASTER LSB OUT
1.If configured as output
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure 32. LPSPI Master mode timing (CPHA = 1)
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
52
Electrical characteristics
s
Table 46. LPSPI Slave mode timing
Number
Symbol
Description
Frequency of operation
Min.
Max.
Units
Note
1
1
2
fSCK
tSCK
tLead
tLag
tWSCK
tSU
0
fperiph / 2
—
Hz
ns
2
SCK period
2 x tperiph
3
Enable lead time
1
—
tperiph
tperiph
ns
—
—
—
—
4
Enable lag time
1
—
5
Clock (SCK) high or low time
Data setup time (inputs)
Data hold time (inputs)
Slave access time
tSCK / 2 - 5
—
6
2.7
3.8
—
—
—
0
—
ns
7
tHI
—
ns
—
3
8
ta
tperiph
tperiph
14.5
—
ns
4
9
tdis
Slave MISO disable time
Data valid (after SCK edge)
Data hold time (outputs)
ns
10
11
tV
ns
—
—
tHO
ns
1
Absolute maximum frequency of operation (fop) is 30 MHz. The clock driver in the LPSPI module for fperiph must be
guaranteed this limit is not exceeded.
2
3
4
tperiph = 1 / fperiph
Time to data active from high-impedance state
Hold time to high-impedance state
PCS
(INPUT)
2
4
SCK
(CPOL=0)
(INPUT)
5
5
3
SCK
(CPOL=1)
(INPUT)
9
8
10
11
11
see
note
SEE
NOTE
SIN
(OUTPUT)
BIT 6 . . . 1
SLAVE MSB
7
SLAVE LSB OUT
6
SOUT
(INPUT)
LSB IN
MSB IN
BIT 6 . . . 1
NOTE: Not defined
Figure 33. LPSPI Slave mode timing (CPHA = 0)
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
53
Electrical characteristics
PCS
(INPUT)
4
2
3
SCK
(CPOL=0)
(INPUT)
5
5
SCK
(CPOL=1)
(INPUT)
11
9
10
SLAVE MSB OUT
see
note
SIN
(OUTPUT)
BIT 6 . . . 1
BIT 6 . . . 1
SLAVE LSB OUT
LSB IN
8
6
7
SOUT
MSB IN
(INPUT)
Figure 34. LPSPI Slave mode timing (CPHA = 1)
4.8.2
LPI2C module timing parameters
This section describes the timing parameters of the LPI2C module.
Table 47. LPI2C module timing parameters
Symbol
Description
Standard mode (Sm)
Min
Max
100
Unit
Notes
1, 2
fSCL
SCL clock frequency
0
0
0
0
0
kHz
Fast mode (Fm)
400
Fast mode Plus (Fm+)
Ultra Fast mode (UFm)
High speed mode (Hs-mode)
1000
5000
3400
1
Hs-mode is only supported in slave mode.
See General switching specifications.
2
4.8.2.1
Bus operation condition for 3.3 V and 1.8 V signaling
Signaling level of SD/eMMC4.3 and eMMC4.4/4.41 modes is 3.3 V. Signaling level of SDR104/SDR50
mode is 1.8 V. The DC parameters for the NVCC_SD1 supply are identical to those shown in Table 20,
"Single voltage GPIO DC parameters," on page 26.
4.8.3
LPUART electrical specifications
Please refer to Section 4.3.2.1, General purpose I/O AC parameters.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
54
NXP Semiconductors
Electrical characteristics
4.8.4
USB PHY parameters
This section describes the USB-OTG PHY parameters.
The USB PHY meets the electrical compliance requirements defined in the Universal Serial Bus Revision
2.0 OTG with the following amendments.
•
USB ENGINEERING CHANGE NOTICE
— Title: 5V Short Circuit Withstand Requirement Change
— Applies to: Universal Serial Bus Specification, Revision 2.0
Errata for USB Revision 2.0 April 27, 2000 as of 12/7/2000
USB ENGINEERING CHANGE NOTICE
•
•
— Title: Pull-up/Pull-down resistors
— Applies to: Universal Serial Bus Specification, Revision 2.0
USB ENGINEERING CHANGE NOTICE
•
•
— Title: Suspend Current Limit Changes
— Applies to: Universal Serial Bus Specification, Revision 2.0
USB ENGINEERING CHANGE NOTICE
— Title: USB 2.0 Phase Locked SOFs
— Applies to: Universal Serial Bus Specification, Revision 2.0
On-The-Go and Embedded Host Supplement to the USB Revision 2.0 Specification
— Revision 2.0 plus errata and ecn June 4, 2010
Battery Charging Specification (available from USB-IF)
— Revision 1.2, December 7, 2010
•
•
— Portable device only
4.9
Timers
This section provide information on timers.
4.9.1
Pulse Width Modulator (PWM) characteristics
This section describes the electrical information of the PWM.
Table 48. PWM timing parameters
Parameter
Symbo
Min
Typ
Max
Unit
PWM Clock Frequency
Power-up Time
—
80
—
—
120
—
MHz
tpu
25
s
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
55
Electrical characteristics
4.9.2
Quad timer timing
Table 49 listed the timing parameters.
Table 49. Quad Timer Timing
Min1
Characteristic
Symbo
Max
Unit
See Figure
Timer input period
TIN
TINHL
TOUT
2T + 6
—
—
—
—
ns
ns
ns
ns
Timer input high/low period
Timer output period
1T + 3
33
Timer output high/low period
TOUTHL
16.7
1
T = clock cycle. For 60 MHz operation, T = 16.7 ns.
4IMER )NPUTS
4
4
).(,
).(,
4
).
4IMER /UTPUTS
4
4
/54(,
/54(,
4
/54
Figure 35. Quad timer timing
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
56
Boot mode configuration
5 Boot mode configuration
This section provides information on boot mode configuration pins allocation and boot devices interfaces
allocation.
5.1
Boot mode configuration pins
Table 50 provides boot options, functionality, fuse values, and associated pins. Several input pins are also
sampled at reset and can be used to override fuse values, depending on the value of BT_FUSE_SEL fuse.
The boot option pins are in effect when BT_FUSE_SEL fuse is ‘0’ (cleared, which is the case for an
unblown fuse). For detailed boot mode options configured by the boot mode pins, see the i.MX RT1015
Fuse Map document and the System Boot chapter in i.MX RT1015 Reference Manual (IMXRT1015RM).
Table 50. Fuses and associated pins used for boot
Pad
Default setting on reset
eFuse name
Details
GPIO_EMC_16
GPIO_EMC_17
GPIO_EMC_18
GPIO_EMC_19
GPIO_EMC_20
GPIO_EMC_21
GPIO_EMC_22
GPIO_EMC_23
GPIO_EMC_24
GPIO_EMC_25
GPIO_EMC_26
GPIO_EMC_27
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
100 K pull-down
src.BOOT_MODE0
src.BOOT_MODE1
src.BT_CFG[0]
src.BT_CFG[1]
src.BT_CFG[2]
src.BT_CFG[3]
src.BT_CFG[4]
src.BT_CFG[5]
src.BT_CFG[6]
src.BT_CFG[7]
src.BT_CFG[8]
src.BT_CFG[9]
Boot Options, Pin value overrides fuse
settings for BT_FUSE_SEL = ‘0’.
Signal Configuration as Fuse Override
Input at Power Up.
These are special I/O lines that control
the boot up configuration during
product development. In production,
the boot configuration can be
controlled by fuses.
5.2
Boot device interface allocation
The following tables list the interfaces that can be used by the boot process in accordance with the specific
boot mode configuration. The tables also describe the interface’s specific modes and IOMUXC allocation,
which are configured during boot when appropriate.
Table 51. Boot through FlexSPI
PAD Name
GPIO_SD_B1_00
IO Function
flexspi.B_DATA[3]
Mux Mode
Comments
ALT 1
ALT 1
ALT 1
ALT 1
—
—
—
—
GPIO_SD_B1_03
GPIO_SD_B1_04
GPIO_SD_B1_02
flexspi.B_DATA[2]
flexspi.B_DATA[1]
flexspi.B_DATA[0]
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
57
Boot mode configuration
PAD Name
Table 51. Boot through FlexSPI (continued)
IO Function Mux Mode
flexspi.B_SCLK
Comments
GPIO_SD_B1_01
GPIO_SD_B0_05
GPIO_SD_B0_04
GPIO_SD_B0_01
GPIO_SD_B1_05
GPIO_SD_B1_11
GPIO_SD_B0_00
GPIO_SD_B1_07
GPIO_SD_B1_08
GPIO_SD_B1_10
GPIO_SD_B1_09
GPIO_SD_B1_06
ALT 1
ALT 6
ALT 6
ALT 6
ALT 1
ALT 1
ALT 6
ALT 1
ALT 1
ALT 1
ALT 1
ALT 1
—
—
—
—
—
—
—
—
—
—
—
—
flexspi.B_DQS
flexspi.B_SS0_B
flexspi.B_SS1_B
flexspi.A_DQS
flexspi.A_SS0_B
flexspi.A_SS1_B
flexspi.A_SCLK
flexspi.A_DATA[0]
flexspi.A_DATA[1]
flexspi.A_DATA[2]
flexspi.A_DATA[3]
Table 52. Boot through FlexSPI (second option)
IO Function Mux Mode
flexspi.A_DATA[3]
PAD Name
Comments
GPIO_AD_B1_00
GPIO_AD_B1_01
GPIO_AD_B1_02
GPIO_AD_B1_03
GPIO_AD_B1_04
GPIO_AD_B1_05
ALT 1
ALT 1
ALT 1
ALT 1
ALT 1
ALT 1
—
—
—
—
—
—
flexspi.A_SCLK
flexspi.A_DATA[0]
flexspi.A_DATA[2]
flexspi.A_DATA[1]
flexspi.A_SS0_B
Table 53. FlexSPI reset
PAD Name
IO Function
Mux Mode
Mux Mode
Comments
Comments
GPIO_AD_B1_13
gpio1.IO[29]
ALT 5
—
Table 54. Boot through SPI-1
IO Function
PAD Name
GPIO_AD_B0_10
GPIO_AD_B0_11
GPIO_AD_B0_12
GPIO_AD_B0_13
lpspi1.SCK
lpspi1.PCS0
lpspi1.SDO
lpspi1.SDI
ALT 1
—
—
—
—
ALT 1
ALT 1
ALT 1
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
58
Boot mode configuration
Comments
Table 55. Boot through SPI-2
IO Function
PAD Name
GPIO_SD_B1_07
Mux Mode
Mux Mode
Mux Mode
lpspi2.SCK
lpspi2.SDO
lpspi2.SDI
ALT 4
—
—
—
—
GPIO_SD_B1_08
GPIO_SD_B1_09
GPIO_SD_B1_06
ALT 4
ALT 4
ALT 4
lpspi2.PCS0
Table 56. Boot through UART1
IO Function
PAD Name
Comments
GPIO_AD_B0_06
GPIO_AD_B0_07
GPIO_AD_B0_08
GPIO_AD_B0_09
lpuart1.TX
ALT 2
—
—
—
—
lpuart1.RX
ALT 2
ALT 2
ALT 2
lpuart1.CTS_B
lpuart1.RTS_B
Table 57. Boot through UART2
IO Function
PAD Name
Comments
GPIO_AD_B1_06
GPIO_AD_B1_07
GPIO_AD_B1_08
GPIO_AD_B1_09
lpuart2.CTS_B
lpuart2.RTS_B
lpuart2.TX
ALT 2
—
—
—
—
ALT 2
ALT 2
ALT 2
lpuart2.RX
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
59
Package information and contact assignments
6 Package information and contact assignments
This section includes the contact assignment information and mechanical package drawing.
6.1
14 x 14 mm package information
14 x 14 mm, 0.5 mm pitch, ball matrix
6.1.1
Figure 36 shows the top and side views of the 14 x 14 mm LQFP package.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
60
NXP Semiconductors
Package information and contact assignments
ꢁ
ꢊM
ꢋꢅꢆM ꢇM
3M ꢃꢁM
ꢃꢈM <'6:M
ꢀEM
ꢉ
ꢀEM
ꢁꢂꢃꢁM %M ꢄꢅꢆM ꢇM
3M
7'0M ꢌM '0ꢇꢍFꢎKM
ꢀꢀꢁꢀꢀ
ꢀꢂꢁ ꢃꢄꢅꢂꢆꢁ ꢁꢇꢁꢈꢉꢊ
ꢀꢁ
ꢇꢈꢉ
ꢀꢁꢁꢁꢁꢁꢁꢂꢃꢄꢅꢆꢆꢆꢆꢆ
A'ꢍDM ꢋ
L
ꢀꢁ ꢄꢅꢆ
ꢂꢃ
ꢇꢃ
ꢀꢁꢂꢃꢄꢌꢃHꢏM
ꢀꢁ
ꢂ
ꢁ
:ꢍꢊ<'0#M ꢀꢁ ꢀꢈꢉꢁ ꢊꢋꢌꢃ ꢍꢎꢏꢐꢃ
ꢀ
ꢌꢁꢐEM
ꢁM
ꢑꢒꢓ
ꢀꢁꢂꢃꢄꢅ
ꢉM
IM
JM
Jꢔ
6+ꢊ0ꢍM
ꢑꢅꢒꢆꢃ ꢄꢅꢆꢇꢃ
Figure 36. 14 x 14 mm LQFP, case x package top and side Views
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
61
Package information and contact assignments
6.1.2
14 x 14 mm supplies contact assignments and functional contact
assignments
Table 58 shows the device connection list for ground, sense, and reference contact signals.
Table 58. 14 x 14 mm supplies contact assignment
Supply Rail Name
Pin(s) Position(s)
Remark
DCDC_IN
23
27
24
25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DCDC_IN_Q
DCDC_GND
DCDC_LP
DCDC_PSWITCH 26
NVCC_GPIO
NGND_KEL0
NVCC_PLL
5, 20, 58, 71, 80, 95
43
50
44
48
VDD_HIGH_CAP
VDD_HIGH_IN
VDD_SNVS_CAP 35
VDD_SNVS_IN
VDD_SOC_IN
VDD_USB_CAP
VDDA_ADC_3P3
VSS
34
18, 28, 69, 81, 91
40
51
19, 29, 39, 49, 59, 70, 79, 92
Table 59 shows an alpha-sorted list of functional contact assignments for the 14 x 14 mm package.
Table 59. 14 x 14 mm functional contact assignments
Default Setting
14 x 14
Pin
Power
Group
Pin
Type
Pin Name
Default
Mode
Default
Function
Input/
Output
Value
GPIO_AD_B0_00
GPIO_AD_B0_01
GPIO_AD_B0_02
GPIO_AD_B0_03
GPIO_AD_B0_04
78
77
76
75
74
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
Digital
GPIO
ALT0
ALT0
ALT0
ALT0
ALT0
jtag_mux.TMS
Input
Input
Input
Input
Input
47 K PU
Digital
GPIO
jtag_mux.TCK
jtag_mux.MOD
jtag_mux.TDI
jtag_mux.TDO
100 K PD
100 K PD
47 K PU
Keeper
Digital
GPIO
Digital
GPIO
Digital
GPIO
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
62
Package information and contact assignments
Table 59. 14 x 14 mm functional contact assignments (continued)
GPIO_AD_B0_05
GPIO_AD_B0_06
GPIO_AD_B0_07
GPIO_AD_B0_08
GPIO_AD_B0_09
GPIO_AD_B0_10
GPIO_AD_B0_11
GPIO_AD_B0_12
GPIO_AD_B0_13
GPIO_AD_B0_14
GPIO_AD_B0_15
GPIO_AD_B1_10
GPIO_AD_B1_11
GPIO_AD_B1_12
GPIO_AD_B1_13
GPIO_AD_B1_14
GPIO_AD_B1_15
GPIO_EMC_041
GPIO_EMC_05
73
72
68
67
66
65
64
63
62
61
60
57
56
55
54
53
52
7
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
Digital
GPIO
ALT0
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
jtag_mux.TRSTB
GPIO1.IO[6]
GPIO1.IO[7]
GPIO1.IO[8]
GPIO1.IO[9]
GPIO1.IO[10]
GPIO1.IO[11]
GPIO1.IO[12]
GPIO1.IO[13]
GPIO1.IO[14]
GPIO1.IO[15]
GPIO1.IO[26]
GPIO1.IO[27]
GPIO1.IO[28]
GPIO1.IO[29]
GPIO1.IO[30]
GPIO1.IO[31]
GPIO2.IO[4]
GPIO2.IO[5]
GPIO2.IO[6]
GPIO2.IO[7]
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
47 K PU
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
6
Digital
GPIO
GPIO_EMC_06
4
Digital
GPIO
GPIO_EMC_07
3
Digital
GPIO
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
63
Package information and contact assignments
Table 59. 14 x 14 mm functional contact assignments (continued)
GPIO_EMC_08
GPIO_EMC_09
GPIO_EMC_16
GPIO_EMC_17
GPIO_EMC_18
GPIO_EMC_19
GPIO_EMC_20
GPIO_EMC_21
GPIO_EMC_22
GPIO_EMC_23
GPIO_EMC_24
GPIO_EMC_25
GPIO_EMC_26
GPIO_EMC_27
GPIO_EMC_32
GPIO_EMC_33
GPIO_EMC_34
GPIO_EMC_35
GPIO_SD_B1_00
GPIO_SD_B1_01
GPIO_SD_B1_02
2
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
Digital
GPIO
ALT5
ALT5
ALT6
ALT6
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
GPIO2.IO[8]
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Keeper
Keeper
100 k PD
100 k PD
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
1
Digital
GPIO
GPIO2.IO[9]
100
99
98
97
96
94
93
90
89
88
87
86
85
84
83
82
22
21
17
Digital
GPIO
src.BOOT_MODE[0]
src.BOOT_MODE[1]
GPIO2.IO[18]
GPIO2.IO[19]
GPIO2.IO[20]
GPIO2.IO[21]
GPIO2.IO[22]
GPIO2.IO[23]
GPIO2.IO[24]
GPIO2.IO[25]
GPIO2.IO[26]
GPIO2.IO[27]
GPIO3.IO[0]
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
GPIO3.IO[1]
Digital
GPIO
GPIO3.IO[2]
Digital
GPIO
GPIO3.IO[3]
Digital
GPIO
GPIO3.IO[20]
GPIO3.IO[21]
GPIO3.IO[22]
Digital
GPIO
Digital
GPIO
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
64
Package information and contact assignments
Table 59. 14 x 14 mm functional contact assignments (continued)
GPIO_SD_B1_03
GPIO_SD_B1_04
GPIO_SD_B1_05
GPIO_SD_B1_06
GPIO_SD_B1_07
GPIO_SD_B1_08
GPIO_SD_B1_09
GPIO_SD_B1_10
GPIO_SD_B1_11
ONOFF
16
15
14
13
12
11
10
9
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
NVCC_GPIO
VDD_SNVS_IN
VDD_SNVS_IN
VDD_SNVS_IN
Digital
GPIO
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT5
ALT0
ALT0
ALT0
GPIO3.IO[23]
GPIO3.IO[24]
GPIO3.IO[25]
GPIO3.IO[26]
GPIO3.IO[27]
GPIO3.IO[28]
GPIO3.IO[29]
GPIO3.IO[30]
GPIO3.IO[31]
src.RESET_B
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
Keeper
100 K PU
100 K PU
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
Digital
GPIO
8
Digital
GPIO
30
33
31
Digital
GPIO
PMIC_ON_REQ
POR_B
Digital
GPIO
snvs_lp.PMIC_ON_REQ Input
Digital
GPIO
src.POR_B
Output 100 K PU
RTC_XTALI
RTC_XTALO
TEST_MODE
36
37
32
—
—
—
—
—
—
—
—
—
—
—
—
VDD_SNVS_IN
Digital
GPIO
ALT0
tcu.TEST_MODE
Input
100 K PD
USB_OTG1_CHD_B
USB_OTG1_DN
USB_OTG1_DP
USB_OTG1_VBUS
XTALI
45
41
42
38
46
47
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
XTALO
1
This pin output is in a high level until the system reset is complete.
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
65
Package information and contact assignments
6.1.3
14 x 14 mm package pin assignments
Figure 37 shows the pin assignments of the 14 x 14 mm package.
ꢉ
ꢇꢀ
ꢇꢈ
ꢇꢂ
ꢇꢁ
ꢇꢉ
ꢇꢄ
ꢃꢅ
ꢃꢆ
ꢃꢇ
ꢃꢃ
ꢃꢀ
ꢃꢈ
ꢃꢂ
ꢃꢁ
ꢃꢉ
ꢃꢄ
ꢀꢅ
ꢀꢆ
ꢀꢇ
ꢀꢃ
ꢀꢀ
ꢀꢈ
ꢀꢂ
ꢀꢁ
ꢀꢉ
'0)/?%-#?ꢄꢅ
'0)/?%-#?ꢄꢆ
'0)/?%-#?ꢄꢇ
'0)/?%-#?ꢄꢃ
.6##?'0)/
'0)/?!$?"ꢄ?ꢄꢂ
'0)/?!$?"ꢄ?ꢄꢈ
'0)/?!$?"ꢄ?ꢄꢀ
'0)/?!$?"ꢄ?ꢄꢃ
.6##?'0)/
ꢁ
ꢂ
ꢈ
ꢀ
ꢃ
633
'0)/?%-#?ꢄꢀ
'0)/?%-#?ꢄꢈ
'0)/?3$?"ꢉ?ꢉꢉ
'0)/?3$?"ꢉ?ꢉꢄ
'0)/?3$?"ꢉ?ꢄꢅ
'0)/?3$?"ꢉ?ꢄꢆ
'0)/?3$?"ꢉ?ꢄꢇ
'0)/?3$?"ꢉ?ꢄꢃ
'0)/?3$?"ꢉ?ꢄꢀ
'0)/?3$?"ꢉ?ꢄꢈ
'0)/?3$?"ꢉ?ꢄꢂ
'0)/?3$?"ꢉ?ꢄꢁ
6$$?3/#?).
633
ꢇ
6$$?3/#?).
ꢆ
'0)/?!$?"ꢄ?ꢄꢇ
'0)/?!$?"ꢄ?ꢄꢆ
'0)/?!$?"ꢄ?ꢄꢅ
'0)/?!$?"ꢄ?ꢉꢄ
'0)/?!$?"ꢄ?ꢉꢉ
'0)/?!$?"ꢄ?ꢉꢁ
'0)/?!$?"ꢄ?ꢉꢂ
'0)/?!$?"ꢄ?ꢉꢈ
'0)/?!$?"ꢄ?ꢉꢀ
633
ꢅ
ꢉꢄ
ꢉꢉ
ꢉꢁ
ꢉꢂ
ꢉꢈ
ꢉꢀ
ꢉꢃ
ꢉꢇ
ꢉꢆ
ꢉꢅ
ꢁꢄ
ꢁꢉ
ꢁꢁ
ꢁꢂ
ꢁꢈ
ꢁꢀ
.6##?'0)/
'0)/?!$?"ꢉ?ꢉꢄ
'0)/?!$?"ꢉ?ꢉꢉ
'0)/?!$?"ꢉ?ꢉꢁ
'0)/?!$?"ꢉ?ꢉꢂ
'0)/?!$?"ꢉ?ꢉꢈ
'0)/?!$?"ꢉ?ꢉꢀ
6$$!?!$#?ꢂ0ꢂ
.6##?'0)/
'0)/?3$?"ꢉ?ꢄꢉ
'0)/?3$?"ꢉ?ꢄꢄ
$#$#?).
$#$#?'.$
$#$#?,0
Figure 37. The pin assignments of the 14 x 14 mm package
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
66
Revision history
7 Revision history
Table 60 provides a revision history for this data sheet.
Table 60. i.MX RT1015 data sheet document revision history
Rev. Number
Date
Substantive Change(s)
Rev. 2
03/2021
• Updated the M7 Core and external memory descriptions in the Section 1.1, Features
• Updated the Figure 1, "Part number nomenclature—i.MX RT10XX family"
• Updated the frequency of RTC OSC and baud rates of LPUART in the Table 2, i.MX
RT1015 modules list
• Updated the descriptions about TEST_MODE in the Table 3, Special signal
considerations
• Added system and bus frequencies in the Table 9, Operating ranges
• Updated the test conditions and max current of DCDC_IN in the Table 11, Maximum
supply currents
• Added a note in the Section 4.2.1.1, Power-up sequence
• Updated the value of reference clock in the Table 16, Ethernet PLL’s electrical
parameters
• Added the high-level and low-level output current in the Table 20, Single voltage GPIO
DC parameters
• Added a footnote for GPIO_EMC_04 in the Table 59, 14 x 14 mm functional contact
assignments
Rev. 1
04/2019
03/2019
• Updated the SNVS descriptions in the Table 2, i.MX RT1015 modules list
• Updated the Section 4.8.1, LPSPI timing parameters
Rev. 0.1
• Added audio information in the Section 1, i.MX RT1015 introduction
• Updated FlexPWMs and Quadrature Encoder/Decoder in the Section 1.1, Features
• Updated the Table 1, Ordering information
• Updated keypad and GP timer numbers in the Figure 2, "i.MX RT1015 system block
diagram"
• Changed keypad to 4 x 4 in the Table 2, i.MX RT1015 modules list
• Removed the USB OTG2 from the Table 2, i.MX RT1015 modules list, Table 7, Absolute
maximum ratings, and Section 4.2.1.1, Power-up sequence
• Updated on-chip termination information for the JTAG_TCK and JTAG_MOD in the
Table 4, JTAG controller interface summary
• Updated descriptions in the Section 4.2.2.2.3, LDO_USB
• Changed the 528 MHz PLL to System PLL in the Table 15, System PLL’s electrical
parameters
• Changed the 480 MHz PLL to USB PLL in the Table 17, USB PLL’s electrical
parameters
Rev. 0
01/2019
• Initial version
i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021
NXP Semiconductors
67
How To Reach Us
Home Page:
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However,
NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the consequences of use of such information. NXP
Semiconductors takes no responsibility for the content in this document if provided by an information source outside
of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special
or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related
to the removal or replacement of any products or rework charges) whether or not such damages are based on tort
(including negligence), warranty, breach of contract or any other legal theory.
nxp.com
Web Support:
nxp.com/support
Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate
and cumulative liability towards customer for the products described herein shall be limited in accordance with the
Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes - NXP Semiconductors reserves the right to make changes to information published in this
document, including without limitation specifications and product descriptions, at any time and without notice. This
document supersedes and replaces all information supplied prior to the publication hereof.
Security — Customer understands that all NXP products may be subject to unidentified or documented vulnerabilities.
Customer is responsible for the design and operation of its applications and products throughout their lifecycles to
reduce the effect of these vulnerabilities on customer’s applications and products. Customer’s responsibility also
extends to other open and/or proprietary technologies supported by NXP products for use in customer’s applications.
NXP accepts no liability for any vulnerability. Customer should regularly check security updates from NXP and follow
up appropriately.
Customer shall select products with security features that best meet rules, regulations, and standards of the intended
application and make the ultimate design decisions regarding its products and is solely responsible for compliance
with all legal, regulatory, and security related requirements concerning its products, regardless of any information or
support that may be provided by NXP. NXP has a Product Security Incident Response Team (PSIRT) (reachable
at PSIRT@nxp.com) that manages the investigation, reporting, and solution release to security vulnerabilities of
NXP products.
Suitability for use in automotive applications — This NXP Semiconductors product has been qualified for use in
automotive applications. Unless otherwise agreed in writing, the product is not designed, authorized or warranted to
be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure
or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death
or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion
and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use
is at the customer's own risk.
Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors
product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in
accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion
and/or use of non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive
specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b) whenever customer uses the product for
automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk,
and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting
from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard
warranty and NXP Semiconductors’ product specifications.
Suitability for use – Automotive Product (Functional Safety) Suitability for use in automotive applications —This NXP
product has been qualified for use in automotive applications. It has been developed in accordance with ISO 26262,
and has been ASIL-classified accordingly. If this product is used by customer in the development of, or for incorporation
into, products or services (a) used in safety critical applications or (b) in which failure could lead to death, personal
injury, or severe physical or environmental damage (such products and services hereinafter referred to as “Critical
Table continues on the next page...
Applications”), then customer makes the ultimate design decisions regarding its products and is solely responsible
for compliance with all legal, regulatory, safety, and security related requirements concerning its products, regardless
of any information or support that may be provided by NXP. As such, customer assumes all risk related to use of
any products in Critical Applications and NXP and its suppliers shall not be liable for any such use by customer.
Accordingly, customer will indemnify and hold NXP harmless from any claims, liabilities, damages and associated
costs and expenses (including attorneys’ fees) that NXP may incur related to customer’s incorporation of any product
in a Critical Application.
Non-automotive products for restricted use in automotive onlySuitability for use in automotive applications — The use
of this NXP Semiconductors product is restricted to automotive applications only. It has not been fully qualified for use
in automotive applications. The customer of this NXP Semiconductors product therefore understands and accepts that:
•
•
The Customer shall only use this NXP Semiconductors product for automotive applications.
This product was not originally designed for automotive use. It will therefore, not be possible to achieve the levels
of quality and failure analysis that are normally associated with products explicitly designed for automotive use.
•
•
•
With respect to test-coverage, this product is not fully compliant to AEC-Q100.
All product manufacturing locations are certified according to ISO/TS16949.
Unless otherwise agreed in writing, the product is not designed, authorized or warranted to be suitable for use in
life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of
an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property
or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at
the customer's own risk.
Applications — Applications that are described herein for any of these products are for illustrative purposes only.
NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use
without further testing or modification.
Customers are responsible for the design and operation of their applications and products using NXP Semiconductors
products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit
for the customer’s applications and products planned, as well as for the planned application and use of customer’s
third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks
associated with their applications and products.
NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on
any weakness or default in the customer’s applications or products, or the application or use by customer’s third party
customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using
NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or
use by customer’s third party customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of
IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation
of the device at these or any other conditions above those given in the Recommended operating conditions section (if
present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting
values will permanently and irreversibly affect the quality and reliability of the device.
Terms and conditions of commerical sale — NXP Semiconductors products are sold subject to the general terms
and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a
valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the
respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general
terms and conditions with regard to the purchase of NXP Semiconductors products by customer.
Table continues on the next page...
No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that
is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other
industrial or intellectual property rights.
Hazardous voltage — Although basic supply voltages of the product may be much lower, circuit voltages up to 60 V
may appear when operating this product, depending on settings and application. Customers incorporating or otherwise
using these products in applications where such high voltages may appear during operation, assembly, test etc. of such
application, do so at their own risk. Customers agree to fully indemnify NXP Semiconductors for any damages resulting
from or in connection with such high voltages. Furthermore, customers are drawn to safety standards (IEC 950, EN 60
950, CENELEC, ISO, etc.) and other (legal) requirements applying to such high voltages.
Bare die — All die are tested on compliance with their related technical specifications as stated in this data sheet up
to the point of wafer sawing and are handled in accordance with the NXP Semiconductors storage and transportation
conditions. If there are data sheet limits not guaranteed, these will be separately indicated in the data sheet. There are
no post-packing tests performed on individual die or wafers.
NXP Semiconductors has no control of third party procedures in the sawing, handling, packing or assembly of the die.
Accordingly, NXP Semiconductors assumes no liability for device functionality or performance of the die or systems
after third party sawing, handling, packing or assembly of the die. It is the responsibility of the customer to test and
qualify their application in which the die is used. All die sales are conditioned upon and subject to the customer entering
into a written die sale agreement with NXP Semiconductors through its legal department.
Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and
Characteristics sections of this document, and as such is not complete, exhaustive or legally binding.
Export control — This document as well as the item(s) described herein may be subject to export control regulations.
Export might require a prior authorization from competent authorities.
Evaluation products —This product is provided on an “as is” and “with all faults” basis for evaluation purposes only.
NXP Semiconductors, its affiliates and their suppliers expressly disclaim all warranties, whether express, implied or
statutory, including but not limited to the implied warranties of non-infringement, merchantability and fitness for a
particular purpose. The entire risk as to the quality, or arising out of the use or performance, of this product remains with
customer. In no event shall NXP Semiconductors, its affiliates or their suppliers be liable to customer for any special,
indirect, consequential, punitive or incidental damages (including without limitation damages for loss of business,
business interruption, loss of use, loss of data or information, and the like) arising out the use of or inability to use the
product, whether or not based on tort (including negligence), strict liability, breach of contract, breach of warranty or
any other theory, even if advised of the possibility of such damages.
Notwithstanding any damages that customer might incur for any reason whatsoever (including without limitation, all
damages referenced above and all direct or general damages), the entire liability of NXP Semiconductors, its affiliates
and their suppliers and customer’s exclusive remedy for all of the foregoing shall be limited to actual damages incurred
by customer based on reasonable reliance up to the greater of the amount actually paid by customer for the product
or five dollars (US$5.00). The foregoing limitations, exclusions and disclaimers shall apply to the maximum extent
permitted by applicable law, even if any remedy fails of its essential purpose.
Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail
in case of any discrepancy between the translated and English versions.
NXP, the NXP logo, NXP SECURE CONNECTIONS FOR A SMARTER WORLD, COOLFLUX,EMBRACE,
GREENCHIP, HITAG, ICODE, JCOP, LIFE, VIBES, MIFARE, MIFARE CLASSIC, MIFARE DESFire, MIFARE
PLUS, MIFARE FLEX, MANTIS, MIFARE ULTRALIGHT, MIFARE4MOBILE, MIGLO, NTAG, ROADLINK, SMARTLX,
SMARTMX, STARPLUG, TOPFET, TRENCHMOS, UCODE, Freescale, the Freescale logo, CodeWarrior, ColdFire,
ColdFire+, the Energy Efficient Solutions logo, Kinetis, Layerscape, mobileGT, PEG, PowerQUICC, Processor Expert,
QorIQ, QorIQ Qonverge, SafeAssure, the SafeAssure logo, StarCore, Symphony, VortiQa, Vybrid, Airfast, BeeKit,
BeeStack, CoreNet, Flexis, MXC, Platform in a Package, QUICC Engine, Tower, TurboLink, EdgeScale, EdgeLock,
eIQ, and Immersive3D are trademarks of NXP B.V. All other product or service names are the property of their
respective owners. AMBA, Arm, Arm7, Arm7TDMI, Arm9, Arm11, Artisan, big.LITTLE, Cordio, CoreLink, CoreSight,
Table continues on the next page...
Cortex, DesignStart, DynamIQ, Jazelle, Keil, Mali, Mbed, Mbed Enabled, NEON, POP, RealView, SecurCore,
Socrates, Thumb, TrustZone, ULINK, ULINK2, ULINK-ME, ULINK-PLUS, ULINKpro, µVision, Versatile are trademarks
or registered trademarks of Arm Limited (or its subsidiaries) in the US and/or elsewhere. The related technology may
be protected by any or all of patents, copyrights, designs and trade secrets. All rights reserved. Oracle and Java are
registered trademarks of Oracle and/or its affiliates. M, M Mobileye and other Mobileye trademarks or logos appearing
herein are trademarks of Mobileye Vision Technologies Ltd. in the United States, the EU and/or other jurisdictions.
©
NXP B.V. 2021.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 29 April 2021
Document identifier: IMXRT1015CEC
相关型号:
©2020 ICPDF网 联系我们和版权申明