S87C652-5A44-T [NXP]
IC 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQCC44, Microcontroller;型号: | S87C652-5A44-T |
厂家: | NXP |
描述: | IC 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQCC44, Microcontroller 微控制器和处理器 外围集成电路 装置 PC 可编程只读存储器 时钟 |
文件: | 总24页 (文件大小:195K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
87C652/87C654
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
Product specification
Replaces data sheets 87C652 of 1998 May 01 and 87C654 of 1998 May 01
IC20 Data Handbook
1999 Jul 23
Philips
Semiconductors
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
DESCRIPTION
PIN CONFIGURATIONS
The 87C652/87C654 single-chip 8-Bit
microcontroller is manufactured in an
advanced CMOS process and is a derivative
of the 80C51 microcontroller family. The
87C652/87C654 has the same instruction
set as the 80C51. Three versions of the
derivative exist:
40
V
CC
P1.0
P1.1
P1.2
1
2
3
39 P0.0/AD0
38 P0.1/AD1
37
P1.3
P1.4
4
5
P0.2/AD2
36 P0.3/AD3
35
P0.4/AD4
80C652—ROMless
83C652/83C654—8 Kbyte, 16 Kbyte ROM
87C652/87C654—8 Kbyte, 16 Kbyte OTP
P1.5
SCL/P1.6
SDA/P1.7
RST
6
7
8
9
FEATURES
• 80C51 central processing unit
34 P0.5/AD5
33 P0.6/AD6
32 P0.7/AD7
The ROMless and ROM are in separate
datasheets.
• 16k × 8 EPROM or 8k x 8 EPROM
expandable externally to 64k bytes
PLASTIC
DUAL
IN-LINE
This device provides architectural
31 EA/V
PP
RxD/P3.0 10
TxD/P3.1 11
INT0/P3.2 12
enhancements that make it applicable in a
variety of applications for general control
systems. The 87C654 contains a non-volatile
16k × 8 EPROM and the 87C652 contains an
8k x 8 EPROM. Both have a volatile 256 × 8
read/write data memory, four 8-bit I/O ports,
two 16-bit timer/event counters (identical to
the timers of the 80C51), a multi-source,
two-priority-level, nested interrupt structure,
• 256 × 8 RAM, expandable externally to
PACKAGE
30 ALE/PROG
29 PSEN
64k bytes
• Two standard 16-bit timer/counters
• Four 8-bit I/O ports
13
28
INT1/P3.3
P2.7/A15
27 P2.6/A14
26 P2.5/A13
25 P2.4/A12
T0/P3.4 14
T1/P3.5 15
WR/P3.6 16
RD/P3.7 17
XTAL2 18
XTAL1 19
2
• I C-bus serial I/O port with byte oriented
master and slave functions
• Full-duplex UART facilities
2
an I C interface, UART and on-chip oscillator
24
P2.3/A11
23 P2.2/A10
22
and timing circuits. For systems that require
extra capability, the 87C652/87C654 can be
expanded using standard TTL compatible
memories and logic.
• Power control modes
– Idle mode
P2.1/A9
21 P2.0/A8
– Power-down mode
V
20
SS
• Extended temperature range
• OTP package available
The device also functions as an arithmetic
processor having facilities for both binary and
BCD arithmetic plus bit-handling capabilities.
The instruction set consists of over 100
instructions: 49 one-byte, 45 two-byte and 17
three-byte. With a 16 MHz crystal, 58% of the
instructions are executed in 0.75 µs and 40%
in 1.5 µs. Multiply and divide instructions
require 3 µs.
SU00259
• Two speed ranges
– 16 MHz
– 20 MHz
ORDERING INFORMATION
FREQ
MHz
Drawing
Number
EPROM
TEMPERATURE RANGE °C AND PACKAGE
S87C654-4N40
S87C654-4A44
S87C654–4B44
S87C654-5N40
S87C654-5A44
S87C654-5B44
S87C654–7N40
S87C654–7A44
S87C652-4N40
S87C652-4A44
S87C652-4B44
S87C652-5A44
NOTES:
0 to +70, Plastic Dual In-line Package
0 to +70, Plastic Leaded Chip Carrier
0 to +70, Plastic Quad Flat Pack
16
16
16
16
16
16
20
20
16
16
16
16
SOT129-1
SOT187-2
SOT307-2
SOT129-1
SOT187-2
SOT307-2
SOT129-1
SOT187-2
SOT129-1
SOT187-2
SOT307-2
SOT187-2
–40 to +85, Plastic Dual In-line Package
–40 to +85, Plastic Leaded Chip Carrier
–40 to +85, Plastic Quad Flat Pack
0 to +70, Plastic Dual In-line Package
0 to +70, Plastic Leaded Chip Carrier
0 to +70, Plastic Dual In-line Package
0 to +70, Plastic Leaded Chip Carrier
0 to +70, Plastic Quad Flat Pack
–40 to +85, Plastic Leaded Chip Carrier
1. For ROM see 83C654 data sheet and 83C652/80C652 data sheet
2
1999 Jul 23
853-1689 22042
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
BLOCK DIAGRAM
FREQUENCY
REFERENCE
COUNTERS
T0 T1
XTAL2
XTAL1
OSCILLATOR
PROGRAM
MEMORY
(16K x 8
DATA
TWO 16-BIT
TIMER/EVENT
COUNTERS
AND
MEMORY
TIMING
(256 x 8 RAM)
EPROM)
SDA
SHARED
2
I C SERIAL I/O
CPU
WITH
PORT 1
SCL
INTERNAL
INTERRUPTS
64K BYTE BUS
EXPANSION
CONTRTOL
PROG SERIAL PORT
FULL DUPLEX UART
SYNCHRONOUS SHIFT
PROGRAMMABLE I/O
SERIAL IN
SERIAL OUT
INT0
INT1
CONTROL
PARALLEL PORTS,
ADDRESS/DATA BUS
AND I/O PINS
SHARED WITH
PORT 3
EXTERNAL
INTERRUPTS
SU00271
LOGIC SYMBOL
V
V
CC SS
RST
XTAL1
XTAL2
V
/EA
PP
PSEN
PROG/ALE
SCL
SDA
RxD
TxD
INT0
INT1
T0
T1
WR
RD
SU00262
3
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
PLASTIC LEADED CHIP
CARRIER PIN FUNCTIONS
PLASTIC QUAD FLAT PACK
PIN FUNCTIONS
44
34
6
1
40
7
39
1
33
23
LCC
PQFP
11
17
29
18
28
12
22
Pin
1
Function
NC*
Pin
Function
NC*
Pin
1
Function
P1.5
Pin
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Function
P2.5/A13
P2.6/A14
P2.7/A15
PSEN
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
2
P1.0
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
P2.5/A13
P2.6/A14
P2.7/A15
PSEN
2
P1.6/SCL
P1.7/SDA
RST
3
P1.1
3
4
P1.2
4
5
P1.3
5
P3.0/RxD
NC*
ALE/PROG
NC*
6
P1.4
6
7
P1.5
7
P3.1/TxD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
P3.6/WR
P3.7/RD
XTAL2
EA/V
PP
8
P1.6/SCL
P1.7/SDA
RST
8
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
9
9
10
11
12
13
14
15
16
17
18
19
20
21
22
10
11
12
13
14
15
16
17
18
19
20
21
22
P3.0/RxD
NC*
ALE/PROG
NC*
P3.1/TxD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
P3.6/WR
P3.7/RD
XTAL2
XTAL1
EA/V
PP
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
XTAL1
V
V
CC
SS
NC*
NC*
P1.0
P1.1
P1.2
P.13
P1.4
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
V
V
CC
SS
SU00261
* NO INTERNAL CONNECTION
SU00260
* NO INTERNAL CONNECTION
4
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
PIN DESCRIPTIONS
PIN NUMBER
MNEMONIC DIP
LCC
22
QFP
16
TYPE NAME AND FUNCTION
V
SS
V
CC
20
40
I
I
Ground: 0 V reference.
44
38
Power Supply: This is the power supply voltage for normal, idle, and power-down operation.
P0.0–0.7
39–32 43–36 37–30
I/O
Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to them
float and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order
address and data bus during accesses to external program and data memory. In this
application, it uses strong internal pull-ups when emitting 1s. Port 0 also outputs the code
bytes during program verification in the 87C654. External pull-ups are required during
program verification.
P1.0–P1.7
1–8
2–9
40–44,
1–3
I/O
Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups, except P1.6 and P1.7
which are open drain. Port 1 pins that have 1s written to them are pulled high by the internal
pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will
source current because of the internal pull-ups. (See DC Electrical Characteristics: I ).
IL
Port 1 also receives the low-order address byte during program memory verification.
Alternate functions include:
2
P1.6
P1.7
7
8
8
9
2
3
I/O
I/O
SCL: I C-bus serial port clock line.
2
SDA: I C-bus serial port data line.
P2.0–P2.7
21–28 24–31 18–25
I/O
Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs,
port 2 pins that are externally being pulled low will source current because of the internal
pull-ups. (See DC Electrical Characteristics: I ). Port 2 emits the high-order address byte
IL
during fetches from external program memory and during accesses to external data memory
that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal
pull-ups when emitting 1s. During accesses to external data memory that use 8-bit
addresses (MOV @Ri), port 2 emits the contents of the P2 special function register.
P3.0–P3.7
10–17
11,
5,
I/O
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs,
port 3 pins that are externally being pulled low will source current because of the pull-ups.
13–19 7–13
(See DC Electrical Characteristics: I ). Port 3 also serves the special features of the 80C51
IL
family, as listed below:
10
11
12
13
14
15
16
17
11
13
14
15
16
17
18
19
5
7
8
I
O
I
I
I
I
O
O
RxD (P3.0): Serial input port
TxD (P3.1): Serial output port
INT0 (P3.2): External interrupt
INT1 (P3.3): External interrupt
T0 (P3.4): Timer 0 external input
T1 (P3.5): Timer 1 external input
WR (P3.6): External data memory write strobe
RD (P3.7): External data memory read strobe
9
10
11
12
13
RST
9
10
4
I
Reset: A high on this pin for two machine cycles while the oscillator is running, resets the
device. An internal diffused resistor to V permits a power-on reset using only an external
SS
capacitor to V
.
CC
ALE/PROG
30
33
27
I/O
Address Latch Enable/Program Pulse: Output pulse for latching the low byte of the
address during an access to external memory. In normal operation, ALE is emitted at a
constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking.
Note that one ALE pulse is skipped during each access to external data memory. This pin is
also the program pulse input (PROG) during EPROM programming.
PSEN
29
31
32
35
26
29
O
I
Program Store Enable: The read strobe to external program memory. When the 87C654 is
executing code from the external program memory, PSEN is activated twice each machine
cycle, except that two PSEN activations are skipped during each access to external data
memory. PSEN is not activated during fetches from internal program memory.
EA/V
External Access Enable/Programming Supply Voltage: EA must be externally held low to
enable the device to fetch code from external program memory locations 0000H and 1FFFH
for 87C652 and 3FFFH for 87C654. If EA is held high, the device executes from internal
program memory unless the program counter contains an address greater than 3FFFH. This
PP
pin also receives the 12.75 V programming supply voltage (V ) during EPROM programming.
PP
XTAL1
19
18
21
20
15
14
I
Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator
circuits.
XTAL2
O
Crystal 2: Output from the inverting oscillator amplifier.
NOTE:
To avoid “latch-up” effect at power-on, the voltage on any pin at any time must not be higher than V + 0.5 V or V – 0.5 V, respectively.
CC
SS
5
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
Table 1.
8XC652/654 Special Function Registers
DIRECT
ADDRESS MSB
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
RESET
VALUE
SYMBOL
DESCRIPTION
LSB
E0
ACC*
B*
Accumulator
B register
E0H
F0H
E7
F7
E6
F6
E5
F5
E4
F4
E3
F3
E2
F2
E1
F1
00H
F0
00H
DPTR:
Data pointer
(2 bytes)
DPH
DPL
Data pointer high
Data pointer low
83H
82H
00H
00H
AF
EA
AE
BE
AD
ES1
BD
AC
ES0
BC
AB
ET1
BB
AA
EX1
BA
A9
ET0
B9
A8
EX0
B8
IE*#
IP*#
P0*
Interrupt enable
Interrupt priority
Port 0
A8H
B8H
80H
90H
A0H
0x000000B
xx000000B
FFH
BF
–
PS1
85
PS0
84
PT1
83
PX1
82
PT0
81
PX0
80
87
86
AD6
96
AD7
97
AD5
95
AD4
94
AD3
93
AD2
92
AD1
91
AD0
90
P1*#
P2*
Port 1
SDA
A7
SCL
A6
FFH
A5
A13
B5
A4
A12
B4
A3
A11
B3
A2
A10
B2
A1
A9
A0
A8
Port 2
A15
B7
A14
B6
FFH
B1
B0
P3*
Port 3
B0H
87H
RD
SMOD
9F
WR
–
T1
T0
INT1
GF1
9B
INT0
GF0
9A
TXD
PD
99
RXD
IDL
98
FFH
PCON#
Power control
–
–
0xxx0000B
9E
9D
SM2
9C
REN
S0CON*# Serial 0 port control
98H
99H
SM0
SM1
TB8
RB8
TI
RI
00H
S0BUF#
Serial 0 data buffer
xxxxxxxxB
D7
CY
D6
AC
D5
F0
D4
D3
D2
D1
F1
D0
P
PSW*
S1DAT#
SP
Program status word
Serial 1 data
D0H
DAH
81H
RS1
RS0
OV
00H
00H
07H
00H
Stack pointer
S1ADR#
Serial 1 address
DBH
GC
SLAVE ADDRESS
S1STA#
Serial 1 status
D9H
D8H
SC4
DF
SC3
DE
SC2
DD
SC1
DC
SC0
0
0
0
F8H
DB
SI
DA
AA
8A
IT1
D9
D8
S1CON*# Serial 1 control
CR2
8F
ENS1
8E
STA
8D
STO
8C
CR1
89
CR0
88
00000000B
8B
IE1
TCON*
TH1
Timer control
Timer high 1
Timer high 0
Timer low 1
Timer low 0
Timer mode
88H
8DH
8CH
8BH
8AH
89H
TF1
TR1
TF0
TR0
IE0
IT0
00H
00H
00H
00H
00H
00H
TH0
TL1
TL0
TMOD
GATE
C/T
M1
M0
GATE
C/T
M1
M0
*
#
SFRs are bit addressable.
SFRs are modified from or added to the 80C51 SFRs.
6
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
milliseconds) plus two machine cycles. At
power-down is the last instruction executed.
Only the contents of the on-chip RAM are
preserved. A hardware reset is the only way
to terminate the power-down mode. The
control bits for the reduced power modes are
in the special function register PCON. Table 2
shows the state of the I/O ports during low
current operating modes.
OSCILLATOR
CHARACTERISTICS
XTAL1 and XTAL2 are the input and output,
respectively, of an inverting amplifier. The
pins can be configured for use as an on-chip
oscillator, as shown in the Logic Symbol.
power-on, the voltage on V and RST must
CC
come up at the same time for a proper
start-up.
Idle Mode
In the idle mode, the CPU puts itself to sleep
while all of the on-chip peripherals stay
active. The instruction to invoke the idle
mode is the last instruction executed in the
normal operating mode before the idle mode
is activated. The CPU contents, the on-chip
RAM, and all of the special function registers
remain intact during this mode. The idle
mode can be terminated either by any
enabled interrupt (at which time the process
is picked up at the interrupt service routine
and continued), or by a hardware reset which
starts the processor in the same manner as a
power-on reset.
To drive the device from an external clock
source, XTAL1 should be driven while XTAL2
is left unconnected. There are no
requirements on the duty cycle of the
external clock signal, because the input to
the internal clock circuitry is through a
divide-by-two flip-flop. However, minimum
and maximum high and low times specified in
the data sheet must be observed.
2
I C SERIAL
COMMUNICATION—SIO1
2
2
The I C serial port is identical to the I C
serial port on the 8XC552. The operation of
this subsystem is described in detail in the
8XC552 section of this manual.
Reset
Note that in both the 8XC652/4 and the
2
A reset is accomplished by holding the RST
8XC552 the I C pins are alternate functions
pin high for at least two machine cycles (24
oscillator periods), while the oscillator is
running. To insure a good power-on reset, the
RST pin must be high long enough to allow
the oscillator time to start up (normally a few
to port pins P1.6 and P1.7. Because of this,
P1.6 and P1.7 on these parts do not have a
pull-up structure as found on the 80C51.
Therefore P1.6 and P1.7 have open drain
outputs on the 8XC652/4.
Power-Down Mode
In the power-down mode, the oscillator is
stopped and the instruction to invoke
Table 2. External Pin Status During Idle and Power-Down Mode
PROGRAM
MEMORY
MODE
ALE
PSEN
PORT 0
PORT 1
PORT 2
PORT 3
Idle
Idle
Internal
1
1
0
0
1
1
0
0
Data
Float
Data
Float
Data
Data
Data
Data
Data
Address
Data
Data
Data
Data
Data
External
Internal
Power-down
Power-down
External
Data
Serial Control Register (S1CON) – See Table 3
S1CON (D8H)
CR2
ENS1
STA
STO
SI
AA
CR1
CR0
Bits CR0, CR1 and CR2 determine the serial clock frequency that is generated in the master mode of operation.
Table 3. Serial Clock Rates
BIT FREQUENCY (kHz) AT fOSC
6 MHZ
12 MHz
16 MHz
20 MHz
f
DIVIDED BY
CR2
CR1
CR0
OSC
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
23
27
31.25
37
6.25
50
100
47
54
62.5
75
12.5
100
200
62.5
71
83.3
100
17
78
89
104
125
21
166
334
256
224
192
160
960
120
60
1
1
1
1
1
133
1
1
1
267
0.25 < 62.5
0 to 255
0.5 < 62.5
0 to 254
0.65 < 55.6
0 to 253
0.81 < 69.4
0 to 253
96 × (256 – (reload value Timer 1))
(Reload value range: 0 – 254 in mode 2)
NOTE:
2
2
1. These frequencies exceed the upper limit of 100kHz of the I C-bus specification and cannot be used in an I C-bus application.
7
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
1, 2, 3
ABSOLUTE MAXIMUM RATINGS
PARAMETER
RATING
–65 to +150
–0.5 to + 13
–0.5 to + 6.5
±5
UNIT
°C
V
Storage temperature range
Voltage on EA/V to V
PP
SS
Voltage on any other pin to V
V
SS
Input, output current on any single pin
mA
W
Power dissipation (based on package heat transfer
limitations, not device power consumption)
1
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent
damage to the device. This is a stress rating only and functional operation of the device at
these or any conditions other than those described in the AC and DC Electrical
Characteristics section of this specification is not implied.
2. This product includes circuitry specifically designed for the protection of its internal devices
from the damaging effects of excessive static charge. Nonetheless, it is suggested that
conventional precautions be taken to avoid applying greater than the rated maxima.
3. Parameters are valid over operating temperature range unless otherwise specified. All
voltages are with respect to V unless otherwise noted.
SS
DEVICE SPECIFICATIONS
SUPPLY VOLTAGE
(V)
FREQUENCY
(MHz)
TEMPERATURE
RANGE
TYPE
MIN.
MAX.
MIN.
MAX.
(°C)
S87C652-4 and
S87C654-4
4.5
5.5
3.5
16
0 to +70
S87C652-5 and
S87C654-5
4.5
4.5
5.5
5.5
3.5
3.5
16
20
–40 to +85
0 to +70
S87C654–7
8
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
DC ELECTRICAL CHARACTERISTICS
V
SS
= 0 V
TEST
LIMITS
SYMBOL
PARAMETER
Input low voltage,
PART TYPE
CONDITIONS
MIN.
MAX.
0.2V –0.1
UNIT
V
IL
0 to +70°C
–40 to +85°C
–0.5
–0.5
V
V
CC
except EA, P1.6/SCL, P1.7/SDA
0.2V –0.15
CC
V
IL1
Input low voltage to EA
0 to +70°C
–40 to +85°C
–0.5
–0.5
0.2V –0.3
V
V
CC
0.2V –0.35
CC
1
V
V
Input low voltage to P1.6/SCL, P1.7/SDA
–0.5
0.3V
V
IL2
CC
Input high voltage,
0 to +70°C
–40 to +85°C
0.2V +0.9
V
CC
V
CC
+0.5
+0.5
V
V
IH
CC
except XTAL1, RST, P1.6/SCL, P1.7/SDA
Input high voltage, XTAL1, RST
0.2V +1.0
CC
V
IH1
0 to +70°C
–40 to +85°C
0.7V
V
CC
V
CC
+0.5
+0.5
V
V
CC
0.7V +0.1
CC
1
V
V
Input high voltage, P1.6/SCL, P1.7/SDA
0.7V
6.0
V
V
IH2
CC
2, 3
Output low voltage, ports 1, 2, 3,
except P1.6/SCL, P1.7/SDA
I
I
= 1.6mA
0.45
OL
OL
2, 3
V
OL1
V
OL2
V
OH
Output low voltage, port 0, ALE, PSEN
Output low voltage, P1.6/SCL, P1.7/SDA
Output high voltage, ports 1, 2, 3
= 3.2mA
0.45
0.4
V
V
OL
I
= 3.0mA
OL
0 to +70°C
–40 to +85°C
I
I
= –60µA
= –25µA
2.4
0.75V
V
V
OH
OH
CC
V
OH1
Output high voltage; port 0 in external bus mode,
ALE, PSEN, RST
0 to +70°C
–40 to +85°C
I
I
= –400µA
= –150µA
2.4
0.75V
V
V
OH
OH
4
CC
I
IL
Logical 0 input current, ports 1, 2, 3, 4,
except P1.6/SCL, P1.7/SDA
0 to +70°C
–40 to +85°C
V
IN
= 0.45V
–50
–75
µA
µA
I
Logical 1-to-0 transition current, ports 1, 2, 3,
except P1.6/SCL, P1.7/SDA
0 to +70°C
–40 to +85°C
See note 5
0.45V < V < V
CC
–650
–750
µA
µA
TL
I
I
Input leakage current, port 0
±10
±10
µA
L1
I
Input leakage current, P1.6/SCL, P1.7/SDA
0V < V < 6.0V
µA
µA
L2
I
0V < V < 6.0V
CC
I
Power supply current:
See note 6
CC
V
CC
=6.0V
7
Active mode @ 16 MHz
Idle mode @ 16 MHz
25
6
50
135
mA
mA
µA
8
9, 10
Power down mode
0 to +70°C
–40 to +85°C
9, 10
Power down mode
µA
R
C
Internal reset pull-down resistor
Pin capacitance
50
150
10
kΩ
RST
IO
Freq.=1 MHz
pF
NOTES:
2
1. The input threshold voltage of P1.6 and P1.7 (SIO1) meets the I C specification, so an input voltage below 0.3V will be recognized as a
CC
logic 0 while an input voltage above 0.7V will be recognized as a logic 1.
CC
2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V s of ALE and ports 1 and 3. The noise is due
OL
to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
worst cases (capacitive loading > 100 pF), the noise pulse on the ALE pin may exceed 0.8 V. In such cases, it may be desirable to qualify
ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. I can exceed these conditions provided that no
OL
single output sinks more than 5 mA and no more than two outputs exceed the test conditions.
3. Under steady state (non-transient) conditions, I must be externally limited as follows: Maximum I = 10 mA per port pin; Maximum
OL
OL
I
OL
= 26 mA total for Port 0; Maximum I = 15 mA total for Ports 1, 2, and 3; Maximum I = 71 mA total for all output pins. If I exceeds
OL OL OL
the test conditions, V may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions.
OL
4. Capacitive loading on ports 0 and 2 may cause the V on ALE and PSEN to momentarily fall below the 0.9V specification when the
OH
CC
address bits are stabilizing.
5. Pins of ports 1 , 2, and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when V is approximately 2 V.
IN
6. See Figures 9 through 11 for I test conditions.
CC
7. The operating supply current is measured with all output pins disconnected; XTAL1 driven with t = t = 10ns;
r
f
V
IL
= V + 0.5 V; V = V –0.5 V; XTAL2 not connected; EA = RST = Port 0 = P1.6 = P1.7 = V ; f
= 16 MHz. See Figure 9.
SS
IH
CC
CC CLK
8. The idle mode supply current is measured with all output pins disconnected; XTAL1 driven with t = t = 10 ns; V = V + 0.5 V;
r
f
IL
SS
V
IH
= V –0.5 V; XTAL2 not connected; Port 0 = P1.6 = P1.7 = V ; EA = RST = V ; f
= 16 MHz. See Figure 10.
CC
CC
SS CLK
9. The power-down current is measured with all output pins disconnected; XTAL2 not connected; Port 0 = P1.6 = P1.7 = V
;
CC
EA = RST = V . See Figure 11.
SS
10.2V ≤ V ≤ V max.
PD
CC
9
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
1, 2
AC ELECTRICAL CHARACTERISTICS
16 MHz CLOCK
VARIABLE CLOCK
SYMBOL
1/t
FIGURE
PARAMETER
MIN
MAX
MIN
MAX
UNIT
2
Oscillator frequency Speed Versions
3.5
16
MHz
CLCL
87C654
–4, –5
t
t
t
t
t
t
t
t
t
t
t
2
2
2
2
2
2
2
2
2
2
2
ALE pulse width
Address valid to ALE low
85
8
2t
–40
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
LHLL
CLCL
t
–55
AVLL
LLAX
LLIV
CLCL
CLCL
Address hold after ALE low
ALE low to valid instruction in
ALE low to PSEN low
28
t
–35
150
83
4t
3t
–100
CLCL
23
t
–40
LLPL
PLPH
PLIV
PXIX
PXIZ
AVIV
PLAZ
CLCL
PSEN pulse width
143
3t
CLCL
–45
PSEN low to valid instruction in
Input instruction hold after PSEN
Input instruction float after PSEN
Address to valid instruction in
PSEN low to address float
–105
CLCL
0
0
38
208
10
t
–25
CLCL
5t
CLCL
–105
10
Data Memory
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
Address valid to ALE low
RD pulse width
28
t
6t
6t
–35
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
AVLL
CLCL
CLCL
CLCL
275
275
–100
–100
RLRH
WLWH
RLDV
RHDX
RHDZ
LLDV
AVDV
LLWL
AVWL
QVWX
DW
WR pulse width
RD low to valid data in
Data hold after RD
148
5t
–165
CLCL
0
0
Data float after RD
55
2t
–70
CLCL
ALE low to valid data in
Address to valid data in
ALE low to RD or WR low
Address valid to WR low or RD low
Data valid to WR transition
Data setup time before WR
Data hold after WR
350
398
238
8t
CLCL
9t
CLCL
–150
–165
138
120
3
3t
–50
3t
+50
CLCL
CLCL
4t
–130
–60
CLCL
CLCL
CLCL
CLCL
t
288
13
7t
t
–150
–50
WHQX
RLAZ
WHLH
RD low to address float
RD or WR high to ALE high
0
0
23
103
t
–40
t
+40
CLCL
CLCL
Shift Register
3
t
t
t
t
t
5
5
5
5
5
Serial port clock cycle time
0.75
492
80
12t
µs
ns
ns
ns
ns
XLXL
CLCL
3
Output data setup to clock rising edge
10t
–133
QVXH
XHQX
XHDX
XHDV
CLCL
3
Output data hold after clock rising edge
2t
CLCL
–117
3
Input data hold after clock rising edge
0
0
3
Clock rising edge to input data valid
492
10t
–133
CLCL
External Clock
3
t
t
t
t
6
6
6
6
High time
20
20
20
20
t
t
ns
ns
ns
ns
CHCX
CLCX
CLCH
CHCL
CLCL – LOW
3
Low time
t
t
CLCL – HIGH
3
Rise time
20
20
20
3
Fall time
20
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100 pF, load capacitance for all other outputs = 80 pF.
3. These values are characterized but not 100% production tested.
10
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
1, 2
AC ELECTRICAL CHARACTERISTICS
20 MHz CLOCK
VARIABLE CLOCK
SYMBOL
1/t
FIGURE
PARAMETER
MIN
MAX
MIN
MAX
UNIT
2
Oscillator frequency: Speed Versions
3.5
20
MHz
CLCL
87C654
–7, –8
t
t
t
t
t
t
t
t
t
t
t
2
2
2
2
2
2
2
2
2
2
2
ALE pulse width
Address valid to ALE low
60
25
25
2t
–40
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
LHLL
CLCL
t
–25
AVLL
LLAX
LLIV
CLCL
CLCL
Address hold after ALE low
ALE low to valid instruction in
ALE low to PSEN low
t
–25
135
90
4t
3t
–65
CLCL
25
t
–25
LLPL
PLPH
PLIV
PXIX
PXIZ
AVIV
PLAZ
CLCL
PSEN pulse width
105
3t
CLCL
–45
PSEN low to valid instruction in
Input instruction hold after PSEN
Input instruction float after PSEN
Address to valid instruction in
PSEN low to address float
–60
CLCL
0
0
25
170
10
t
–25
CLCL
5t
CLCL
–80
10
Data Memory
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
Address valid to ALE low
RD pulse width
25
t
6t
6t
–25
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
AVLL
CLCL
CLCL
CLCL
200
200
–100
–100
RLRH
WLWH
RLDV
RHDX
RHDZ
LLDV
AVDV
LLWL
AVWL
QVWX
DW
WR pulse width
RD low to valid data in
Data hold after RD
160
5t
2t
–90
–28
CLCL
0
0
Data float after RD
72
CLCL
ALE low to valid data in
Address to valid data in
ALE low to RD or WR low
Address valid to WR low or RD low
Data valid to WR transition
Data setup time before WR
Data hold after WR
250
285
200
8t
–150
–165
CLCL
CLCL
9t
100
125
20
3t
–50
–75
3t
CLCL
+50
CLCL
4t
CLCL
t
CLCL
7t
CLCL
t
CLCL
–30
220
25
–130
–25
WHQX
RLAZ
WHLH
RD low to address float
RD or WR high to ALE high
0
0
25
75
t
–25
t
+25
CLCL
CLCL
Shift Register
3
t
t
t
t
t
5
5
5
5
5
Serial port clock cycle time
0.6
367
40
0
12t
µs
ns
ns
ns
ns
XLXL
CLCL
3
Output data setup to clock rising edge
10t
–133
–60
QVXH
XHQX
XHDX
XHDV
CLCL
3
Output data hold after clock rising edge
2t
CLCL
3
Input data hold after clock rising edge
0
3
Clock rising edge to input data valid
367
10t
–133
CLCL
External Clock
3
t
t
t
t
6
6
6
6
High time
17
17
17
17
t
t
ns
ns
ns
ns
CHCX
CLCX
CLCH
CHCL
CLCL – LOW
3
Low time
t
t
CLCL – HIGH
3
Rise time
20
20
20
3
Fall time
20
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100 pF, load capacitance for all other outputs = 80 pF.
3. These values are characterized but not 100% production tested.
11
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
2
AC ELECTRICAL CHARACTERISTICS – I C INTERFACE
SYMBOL
PARAMETER
INPUT
OUTPUT
SCL TIMING CHARACTERISTICS
1
t
t
t
t
t
; STA START condition hold time
≥ 14 t
> 4.0 µs
HD
CLCL
CLCL
CLCL
1
SCL LOW time
SCL HIGH time
SCL rise time
SCL fall time
≥ 16 t
≥ 14 t
> 4.7 µs
LOW
HIGH
RC
1
> 4.0 µs
2
≤ 1 µs
–
3
≤ 0.3 µs
< 0.3 µs
FC
SDA TIMING CHARACTERISTICS
t
t
t
t
t
t
t
t
t
; DAT1
; DAT2
; DAT3
; DAT
Data set-up time
≥ 250 ns
≥ 250 ns
≥ 250 ns
≥ 0 ns
> 20 t
– t
SU
SU
SU
HD
SU
SU
CLCL
RD
FC
1
SDA set-up time (before rep. START cond.)
SDA set-up time (before STOP cond.)
Data hold time
> 1 µs
> 8 t
CLCL
> 8 t
– t
CLCL
1
; STA
Repeated START set-up time
STOP condition set-up time
Bus free time
≥ 14 t
≥ 14 t
≥ 14 t
> 4.7 µs
> 4.0 µs
> 4.7 µs
CLCL
CLCL
CLCL
1
1
; STO
BUF
RD
2
SDA rise time
≤ 1µs
≤ 0.3µs
–
3
SDA fall time
< 0.3 µs
FD
NOTES:
1. At 100 kbit/s. At other bit rates this value is inversely proportional to the bit-rate of 100 kbit/s.
2. Determined by the external bus-line capacitance and the external bus-line pull-resistor, this must be < 1 µs.
3. Spikes on the SDA and SCL lines with a duration of less than 3 t
will be filtered out. Maximum capacitance on bus-lines SDA and
CLCL
SCL = 400 pF.
4. t
= 1/f
= one oscillator clock period at pin XTAL1. For 62 ns < t
< 285 ns (16 MHz) > f
> 3.5 MHz) the SI01 interface meets
OSC
CLCL
OSC
CLCL
2
the I C-bus specification for bit-rates up to 100 kbit/s.
2
TIMING SIO1 (I C) INTERFACE
repeated START condition
STOP condition
START or repeated START condition
START condition
t
SU;STA
t
RD
0.7 V
CC
SDA
(INPUT/OUTPUT)
0.3 V
CC
t
BUF
t
t
t
FC
FD
RC
t
SU;STO
0.7 V
CC
SCL
(INPUT/OUTPUT)
0.3 V
CC
t
SU;DAT3
t
t
t
t
SU;DAT1
t
t
HD;STA
LOW
HIGH
HD;DAT
SU;DAT2
SU00107A
12
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
EXPLANATION OF THE AC SYMBOLS
Each timing symbol has five characters. The
first character is always ‘t’ (= time). The other
characters, depending on their positions,
indicate the name of a signal or the logical
status of that signal. The designations are:
A – Address
Q – Output data
R – RD signal
– Time
V – Valid
W – WR signal
t
X – No longer a valid logic level
Z – Float
C – Clock
D – Input data
H – Logic level high
Examples: t
= Time for address valid
to ALE low.
AVLL
I
– Instruction (program memory contents)
t
= Time for ALE low
to PSEN low.
LLPL
L – Logic level low, or ALE
P – PSEN
t
LHLL
ALE
t
t
LLPL
AVLL
t
PLPH
t
LLIV
t
PLIV
PSEN
t
LLAX
t
PXIZ
t
PLAZ
t
PXIX
A0–A7
INSTR IN
A0–A7
PORT 0
PORT 2
t
AVIV
A0–A15
A8–A15
SU00006
Figure 1. External Program Memory Read Cycle
ALE
PSEN
RD
t
WHLH
t
LLDV
t
t
LLWL
RLRH
t
RHDZ
t
LLAX
t
t
RLDV
AVLL
t
RLAZ
t
RHDX
A0–A7
FROM RI OR DPL
PORT 0
PORT 2
DATA IN
A0–A7 FROM PCL
INSTR IN
t
AVWL
t
AVDV
P2.0–P2.7 OR A8–A15 FROM DPH
A8–A15 FROM PCH
SU00177
Figure 2. External Data Memory Read Cycle
13
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
ALE
t
WHLH
PSEN
t
t
WLWH
LLWL
WR
t
t
t
LLAX
WHQX
t
AVLL
QVWX
t
DW
A0–A7
FROM RI OR DPL
PORT 0
PORT 2
DATA OUT
A0–A7 FROM PCL
INSTR IN
t
AVWL
P2.0–P2.7 OR A8–A15 FROM DPH
A8–A15 FROM PCH
SU00213
Figure 3. External Data Memory Write Cycle
INSTRUCTION
ALE
0
1
2
3
4
5
6
7
8
t
XLXL
CLOCK
t
XHQX
t
QVXH
OUTPUT DATA
0
1
2
3
4
5
6
7
WRITE TO SBUF
t
XHDX
t
SET TI
VALID
XHDV
INPUT DATA
CLEAR RI
VALID
VALID
VALID
VALID
VALID
VALID
VALID
SET RI
SU00027
Figure 4. Shift Register Mode Timing
V
–0.5
CC
0.7V
CC
CC
0.45V
0.2V
–0.1
t
CHCX
t
t
t
CHCL
CLCX
CLCH
t
CLCL
SU00009
Figure 5. External Clock Drive
14
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
V
–0.5
CC
0.2V
0.2V
+0.9
–0.1
CC
CC
0.45V
NOTE:
AC inputs during testing are driven at V –0.5 for a logic ‘1’ and 0.45V for a logic ‘0’.
CC
Timing measurements are made at V min for a logic ‘1’ and V max for a logic ‘0’.
IH
IL
SU00010
Figure 6. AC Testing Input/Output
V
V
+0.1V
LOAD
V
V
–0.1V
TIMING
REFERENCE
POINTS
OH
V
LOAD
–0.1V
LOAD
+0.1V
OL
NOTE:
For timing purposes, a port is no longer floating when a 100mV change from load voltage occurs,
and begins to float when a 100mV change from the loaded V /V level occurs. I /I ≥ ±20mA.
OH OL
OH OL
SU00011
Figure 7. Float Waveform
V
CC
CC
I
CC
V
CC
V
V
CC
P0
RST
EA
P1.6
P1.7
87C652/4
*
*
(NC)
XTAL2
XTAL1
CLOCK SIGNAL
V
SS
SU00272
Figure 8. I Test Condition, Active Mode
CC
All other pins are disconnected
NOTE:
Ports 1.6 and 1.7 should be connected to V through resistors of sufficiently high value such that the sink current into these pins does not
*
CC
exceed the I
specification.
OL1
15
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
V
CC
CC
I
CC
V
CC
P0
V
RST
EA
87C652/4
P1.6
P1.7
*
(NC)
CLOCK SIGNAL
XTAL2
XTAL1
*
V
SS
SU00273
Figure 9. I Test Condition, Idle Mode
CC
All other pins are disconnected
V
–0.5
CC
0.7V
CC
CC
0.45V
0.2V
–0.1
t
CHCX
t
t
t
CHCL
CLCX
CLCH
t
CLCL
SU00009
Figure 10. Clock Signal Waveform for I Tests in Active and Idle Modes
CC
t
= t
= 10 ns
CHCL
CLCH
V
CC
CC
I
CC
V
CC
V
RST
EA
P0
87C652/4
P1.6
P1.7
(NC)
XTAL2
XTAL1
*
*
V
SS
SU00274
Figure 11. I Test Condition, Power Down Mode
CC
All other pins are disconnected. V = 2 V to 5.5 V
CC
NOTE:
Ports 1.6 and 1.7 should be connected to V through resistors of sufficiently high value such that the sink current into these pins does not
*
CC
exceed the I
specification.
OL1
16
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
shown in Figure 12. The code byte to be
programmed into that location is applied to
port 0. RST, PSEN and pins of ports 2 and 3
specified in Table 4 are held at the ‘Program
Code Data’ levels indicated in Table 4. The
ALE/PROG is pulsed low 25 times as shown
in Figure 13.
program verification. The address of the
program memory locations to be read is
applied to ports 1 and 2 as shown in
Figure 14. The other pins are held at the
‘Verify Code Data’ levels indicated in Table 4.
The contents of the address location will be
emitted on port 0. External pull-ups are
required on port 0 for this operation.
EPROM CHARACTERISTICS
The 87C652/87C654 is programmed by using
a modified Quick-Pulse Programming
algorithm. It differs from older methods in the
value used for V (programming supply
PP
voltage) and in the width and number of the
ALE/PROG pulses.
To program the encryption table, repeat the 25
pulse programming sequence for addresses 0
through 1FH, using the ‘Pgm Encryption Table’
levels. Do not forget that after the encryption
table is programmed, verification cycles will
produce only encrypted data.
The 87C652/87C654 contains two signature
bytes that can be read and used by an
EPROM programming system to identify the
device. The signature bytes identify the device
as an 87C652/87C654 manufactured by
Philips Components.
If the encryption table has been programmed,
the data presented at port 0 will be the
exclusive NOR of the program byte with one
of the encryption bytes. The user will have to
know the encryption table contents in order to
correctly decode the verification data. The
encryption table itself cannot be read out.
To program the lock bits, repeat the 25 pulse
programming sequence using the ‘Pgm Lock
Bit’ levels. After one lock bit is programmed,
further programming of the code memory and
encryption table is disabled. However, the
other lock bit can still be programmed.
Table 4 shows the logic levels for reading the
signature byte, and for programming the
program memory, the encryption table, and
the lock bits. The circuit configuration and
waveforms for quick-pulse programming are
shown in Figures 12 and 13. Figure 14 shows
the circuit configuration for normal program
memory verification.
Reading the Signature Bytes
The signature bytes are read by the same
procedure as a normal verification of
locations 030H and 031H, except that P3.6
and P3.7 need to be pulled to a logic low. The
values are:
(030H) = 15H indicates manufactured by
Philips
(031H) = 99H
Note that the EA/V pin must not be allowed
PP
to go above the maximum specified V level
PP
for any amount of time. Even a narrow glitch
above that voltage can cause permanent
Quick-Pulse Programming
The setup for microcontroller quick-pulse
programming is shown in Figure 12. Note
that the 87C652/87C654 is running with a
4 to 6 MHz oscillator. The reason the
oscillator needs to be running is that the
device is executing internal address and
program data transfers.
damage to the device. The V source
PP
should be well regulated and free of glitches
and overshoot.
Program/Verify Algorithms
Any algorithm in agreement with the
conditions listed in Table 4, and which
satisfies the timing specifications, is suitable.
Program Verification
If lock bit 2 has not been programmed, the
on-chip program memory can be read out for
The address of the EPROM location to be
programmed is applied to ports 1 and 2, as
Table 4. EPROM Programming Modes
MODE
Read signature
RST
PSEN
ALE/PROG
EA/V
P2.7
P2.6
P3.7
P3.6
PP
1
1
1
1
1
1
0
0
0
0
0
0
1
1
0
1
0
1
1
1
0
0
0
0
1
1
0
1
1
1
1
0
0
1
1
0
1
0
Program code data
Verify code data
Pgm encryption table
Pgm lock bit 1
0*
1
V
PP
1
0*
0*
0*
V
PP
PP
PP
V
V
Pgm lock bit 2
NOTES:
1. ‘0’ = Valid low for that pin, ‘1’ = valid high for that pin.
2. V = 12.75 V ±0.25 V.
PP
3. V = 5 V±10% during programming and verification.
CC
*
ALE/PROG receives 25 programming pulses while V is held at 12.75 V. Each programming pulse is low for 100 µs (±10 µs) and high for a
PP
minimum of 10 µs.
Trademark phrase of Intel Corporation.
17
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
+5V
V
CC
P0
A0–A7
PGM DATA
+12.75V
P1
1
1
1
RST
P3.6
EA/V
PP
25 100µs PULSES TO GROUND
ALE/PROG
PSEN
0
1
P3.7
87C652/4
XTAL2
P2.7
0
P2.6
4–6MHz
XTAL1
A8–A13
P2.0–P2.5
V
SS
SU00275
Figure 12. Programming Configuration
25 PULSES
1
0
ALE/PROG:
ALE/PROG:
10µs MIN
100µs+10
1
0
SU00018
Figure 13. PROG Waveform
+5V
V
CC
P0
A0–A7
PGM DATA
P1
1
1
1
RST
P3.6
1
1
EA/V
PP
ALE/PROG
PSEN
0
P3.7
87C652/4
0 ENABLE
XTAL2
P2.7
0
P2.6
4–6MHz
XTAL1
A8–A13
P2.0–P2.5
V
SS
SU00276
Figure 14. Program Verification
18
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
EPROM PROGRAMMING AND VERIFICATION CHARACTERISTICS
T
amb
= 21°C to +27°C, V = 5V±10%, V = 0V (See Figure 15)
CC SS
SYMBOL
PARAMETER
MIN
MAX
13.0
50
UNIT
V
V
PP
Programming supply voltage
Programming supply current
Oscillator frequency
12.5
I
PP
mA
MHz
1/t
CLCL
4
6
t
t
t
t
t
t
t
t
t
t
t
t
Address setup to PROG low
Address hold after PROG
Data setup to PROG low
Data hold after PROG
48t
AVGL
CLCL
CLCL
CLCL
CLCL
CLCL
48t
48t
48t
48t
GHAX
DVGL
GHDX
EHSH
SHGL
GHSL
GLGH
AVQV
ELQZ
EHQZ
GHGL
P2.7 (ENABLE) high to V
PP
V
PP
V
PP
setup to PROG low
hold after PROG
10
10
90
µs
µs
µs
PROG width
110
Address to data valid
48t
CLCL
CLCL
CLCL
ENABLE low to data valid
Data float after ENABLE
PROG high to PROG low
48t
48t
0
10
µs
PROGRAMMING*
ADDRESS
VERIFICATION*
ADDRESS
P1.0–P1.7
P2.0–P2.3
t
AVQV
PORT 0
DATA IN
DATA OUT
t
t
GHDX
GHAX
t
t
DVGL
AVGL
ALE/PROG
t
t
t
GHGL
GLGH
t
SHGL
GHSL
LOGIC 1
LOGIC 1
EA/V
PP
LOGIC 0
t
t
t
EHSH
ELQV
EHQZ
P2.7
ENABLE
SU00270
*
FOR PROGRAMMING VERIFICATION SEE FIGURE 12.
FOR VERIFICATION CONDITIONS SEE FIGURE 14.
Figure 15. EPROM Programming and Verification
2
2
Purchase of Philips I C components conveys a license under the Philips’ I C patent
2
to use the components in the I C system provided the system conforms to the
I C specifications defined by Philips. This specification can be ordered using the
2
code 9398 393 40011.
19
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
DIP40: plastic dual in-line package; 40 leads (600 mil)
SOT129-1
20
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
PLCC44: plastic leaded chip carrier; 44 leads
SOT187-2
21
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
QFP44: plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm
SOT307-2
22
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
NOTES
23
1999 Jul 23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller
8K/16K, 256 OTP, I2C
87C652/87C654
Data sheet status
[1]
Data sheet
status
Product
status
Definition
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make changes at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Righttomakechanges—PhilipsSemiconductorsreservestherighttomakechanges, withoutnotice, intheproducts, includingcircuits,standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Copyright Philips Electronics North America Corporation 1999
All rights reserved. Printed in U.S.A.
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Date of release: 07-99
Document order number:
9397-750-06607
Philips
Semiconductors
相关型号:
©2020 ICPDF网 联系我们和版权申明