SA57026DD-T [NXP]
IC VREG 3.3 V FIXED POSITIVE LDO REGULATOR, 0.3 V DROPOUT, PDSO7, SOP-7, Fixed Positive Single Output LDO Regulator;
| 型号： | SA57026DD-T |
| 厂家： | 
NXP |
| 描述： | IC VREG 3.3 V FIXED POSITIVE LDO REGULATOR, 0.3 V DROPOUT, PDSO7, SOP-7, Fixed Positive Single Output LDO Regulator 光电二极管 输出元件 调节器 |
| 文件： | 总8页 (文件大小：79K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
SA57026
300 mA LDO with ON/OFF control and
independent delayed RESET function
Product data
2001 Oct 03
File under Integrated Circuits, Standard Analog
Philips
Semiconductors
Philips Semiconductors
Product data
300 mA LDO with ON/OFF control and
independent delayed RESET function
SA57026
GENERAL DESCRIPTION
The SA57026 has an extremely precise fixed output with a typical
accuracy of ±2%. It is designed to provide very low dropout and low
noise in CD-ROM drives, battery-operated systems, and portable
computers applications. This regulator consists of an internal
voltage reference, an error amplifier, a driver with current limiter, and
a thermal shut-down mechanism.
An Active-LOW RESET is assered when the detected voltage
(V ) falls below the reset voltage threshold. The RESET output
DET
remains low for 30 µs (typical) when zero capacitance connected to
Cd pin. The reset time delay can be adjusted by replacing
cpacitance values from Cd pin to Ground.
The device is available in the SOP-7B package.
FEATURES
APPLICATIONS
• Very low dropout voltage: 500 mV typ. (I = 50 mA)
• CD-ROM drives
out
• High precision output voltage: ±2%
• Output current capacity: 300 mA
• Electronic notebooks, PDAs and palmtop computers
• Cameras, VCRs and camcorders
• PCMCIA cards
• Low noise: 40 mV
typ. @ 20 Hz to 80 KHz and for C = 10 nF
n
rms
• Extremely good line regulation: 10 mV typical
• Extremely good load regulation: 20 mV typical
• Modems
• Battery-operated or hand-held instruments
• Low temperature drift co-efficient to V : ±100 ppm/°C
out
• Internal current limit and thermal shut-down circuits
• Adjustment-free reset detection voltage: 4.2 V typ.
• Delay time can be adjusted by external capacitor
• Wide operating temperature range: –40 °C to +85 °C
BLOCK DIAGRAM
4
5
V
V
IN
OUT
ON/OFF
3
THERMAL
PROTECT
2
RESET
GND
1
7
Cd
SL01528
Figure 1. Block diagram.
2
2001 Oct 03
853–2292 27197
Philips Semiconductors
Product data
300 mA LDO with ON/OFF control and
independent delayed RESET function
SA57026
ORDERING INFORMATION
PACKAGE
TEMPERATURE
RANGE
TYPE NUMBER
NAME
DESCRIPTION
SA57026
SOP-7B
small outline 7-pin surface mount (see dimensional drawing)
–40 to +85 °C
NOTE:
Part number marking
The device has two reset threshold options.
Part number
Marking
A L U
XX
SA57026D 3.3 V
SA57026F 3.3 V
Output voltage (Typ.)
Reset threshold (Typ.)
SA57026DD
SA57026FD
4.20 V
3.90 V
A L V
PIN CONFIGURATION
PIN DESCRIPTION
PIN
1
SYMBOL
DESCRIPTION
GND
Ground.
GND
RESET
ON/OFF
1
2
3
4
7
6
5
Cd
2
RESET RESET signal output pin. The output remains
low while V is below the reset voltage
DET
SA57026
GND
threshold, and for an extnerl set time delay
Cd pin after V
threshold.
rises above reset
DET
V
V
OUT
IN
3
ON/OFF Output voltage on/off control pin. Connect to
if not used.
V
IN
SL01529
ON/OFF = LOW: Voltage output (Pin 5) OFF
ON/OFF = HIGH: Voltage output (Pin 5) ON
Figure 2. Pin configuration.
4
5
6
7
V
Voltage supply input pin.
Regulated voltage output pin.
Ground pin and heat sink.
IN
V
OUT
GND
Cd
Reset delay time capacitor pin.
RESET pin output delay time can be set by
capacitance connected to the Cd pin.
t
t
= 100000 x C
PLH
PLH
: transmission delay time (s).
C: capacitor value (F).
MAXIMUM RATINGS
SYMBOL
PARAMETER
MIN.
–0.3
0
MAX.
UNIT
V
V
Supply voltage
+10
400
IN
I
Output current
mA
°C
OUT
T
Operating temperature
Storage temperature
Power dissipation (Note 1)
–40
–40
–
+85
+125
800
oper
T
stg
°C
P
D
mW
NOTE:
1. When mounted on a 25 × 40 × 1 mm glass epoxy board.
3
2001 Oct 03
Philips Semiconductors
Product data
300 mA LDO with ON/OFF control and
independent delayed RESET function
SA57026
ELECTRICAL CHARACTERISTICS
T
amb
= 25 °C; V
= 1.6 V, unless otherwise specified.
ON/OFF
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
3
MAX.
UNIT
mA
mA
µA
I
I
I
No-load input current 1
No-load input current 2
Input current (OFF)
V
V
= 5 V; I
= 4 V; I
= 0 mA
= 0 mA
–
–
–
8
–
–
ccq1
ccq2
ccq3
IN
OUT
OUT
4
IN
V
= 5 V; V
= 0.4 V
ON/OFF
250
IN
Regulator
V
IN
= 5 V; I
= 30 mA
OUT
V
OUT
Output voltage
SA57026D
SA57025F
3.25
3.25
3.30
3.30
3.35
3.35
V
V
V
Input/output differential voltage
Line regulation
V
= 3.2 V; I = 150 mA
OUT
–
–
–
–
0.15
10
0.3
20
120
–
V
mV
IO
IN
V1
V2
∆V
V
= 4.4 to 5.5 V; I
= 30 mA
IN
OUT
Load regulation
V
IN
= 5 V; I
= 0 to 300 mA
OUT
20
mV
/∆T
V
OUT
Temperature coefficient
T = –20 to +85 °C; V = 5 V
j
100
ppm/°C
OUT
IN
(Note 1)
RR
Ripple rejection (Note 1)
V
IN
= 5 V; f = 120 Hz; V
= 1 V ;
p–p
–
–
50
40
80
120
10
dB
ripple
I
= 30 mA
OUT
V
n
Output noise voltage (Note 1)
V
= 5 V; f = 20 to 80 kHz;
µV
rms
IN
V
ripple
= 1 V ; I
= 30 mA
p–p OUT
I
ON/OFF terminal current
HIGH threshold voltage
LOW threshold voltage
V
= 1.6 V
–
5
–
–
µA
ON
ON/OFF
V
th(H)
V
th(L)
1.6
–0.3
V
+0.3
V
V
IN
0.4
Reset
V
DET
Detection voltage
V
IN
= HIGH-to-LOW
SA57026D
4.11
3.81
4.20
3.90
4.29
3.99
V
V
SA57025F
∆V /∆T
V
temperature coefficient (Note 1)
T = –20 to +85 °C
–
100
–
100
–
–
200
200
±0.1
–
ppm/°C
mV
S
S
j
∆V
Hysteresis voltage
V
= HIGH-to-LOW-to-HIGH
S
IN
V
OL
LOW-level output voltage
Output leakage current
V
= 3.9 V; R = 4.7 kΩ
100
–
mV
IN
L
I
I
I
V
IN
= 5 V
–
µA
LO
LOW-level output current 1
LOW-level output current 2 (Note 1)
V
IN
= 3.9 V; R = 0 Ω
5
–
mA
OL1
OL2
L
V
= 3.9 V; R = 0 Ω;
3
–
–
mA
IN
L
T
amb
= –20 to +80 °C
t
LOW-to-HIGH transmission delay
time (Note 1)
Cd = 0.0 µF
–
30
90
µs
PLH
t
t
Reset delay time
V
IN
= 4 V to 5 V; Cd = 0.1 µF
5
–
10
30
20
90
ms
PLH1
HIGH-to-LOW transmission delay
time (Note 1)
µs
PHL
V
OPL
Threshold operating voltage
V
OL
= 0.4 V
–
0.65
0.85
V
NOTE:
1. The parameter is guaranteed by design.
4
2001 Oct 03
Philips Semiconductors
Product data
300 mA LDO with ON/OFF control and
independent delayed RESET function
SA57026
APPLICATION INFORMATION
RESET output delay operation with an external capacitor from
Cd pin to GND
Input capacitor
An input capacitor of ≥1 µF is required to eliminate the AC coupling
When the supply voltage crosses the release voltage (V
) from a
DET
noise. This capacitor must be located as close as possible to V or
IN
low value to a value higher than the released voltage (V
), the Cd
DET
GND pin (not more than 1 cm) and returned to a clean analog
ground. Any good quality ceramic, tantalum or film capacitor will
work.
pin voltage starts to increase (charges up the external capacitor).
While the RESET output remains at LOW state condition until the
Cd pin voltage reaches the threshold operating voltage (V
) 0.4 V
OPL
Output capacitor
typical; after that, the RESET output is reversed to HIGH state
condition.
Phase compensation is made for securing stable operation, even if
the load current varies. For this reason, an output capacitor with
good frequency characteristics is needed. Set it as close to the
circuit as possible, with wires as short as possible.
The transmission delay time (t
) can be set with the capacitance
PLH
Cd of an external cpacitor as shown in Equation (1):
tPLH + 106 C
Eqn. (1)
Tha value of the output capacitance has to be at least 47 µF
connected from V
to GND. When operating from sources other
OUT
(Time is expressed in seconds; capacitance in Farads.)
than batteries, supply-noise rejection and transient response can be
improved by increasing the value of the input and output capacitors
and employing passive filtering techniques.
PCB layout
The component placement around the LDO should be done carefully
to achieve good dynamic line and load response. The input and
noise capacitors should be kept close to the LDO.
ON/OFF
The regulator is fully enabled when a logic HIGH is applied to this
input. The regulator enters shutdown when a logic LOW is appplied
to this input. During shutdown, regulator output voltage falls to zero,
RESET remains valid and supply current is reduced to 5 µA (typ). If
The rise in junction temperature depends on how efficiently the heat
is carried away from the junction to ambient. The junction to lead
thermal impedance is a characteristic of the package and fixed. The
thermal impedance between lead to ambient can be reduced by
increasing the copper area on the PCB. Increase the input, output
and ground trace area to reduce the junction-to-ambient impedance.
the function is not to be used, the ON/OFF pin should be tied to V
.
IN
RESET output
The SA57066 has an Active-LOW RESET output. The RESET
output is driven Active-LOW within 30 µs typical (when Cd is zero
capacitance). The time delay can be adjusted up to 10 ms typical
(when Cd is 0.1 µF) of V
falling through the reset voltage
DET
threshold. RESET is maintained Active-HIGH after V
thre reset threshold.
rises above
DET
V
IN
V
OUT
4
2
5
7
R
C
1 µF
SA57026
4.7 kΩ
C
OUT
47 µF
Cd
RESET
R
3
1
6
C
0.1 µF
ON/OFF
SL01530
Figure 3. Typical application circuit.
5
2001 Oct 03
Philips Semiconductors
Product data
300 mA LDO with ON/OFF control and
independent delayed RESET function
SA57026
PACKING METHOD
The SA57026 is packed in reels, as shown in Figure 4.
GUARD
BAND
TAPE
TAPE DETAIL
REEL
ASSEMBLY
COVER TAPE
CARRIER TAPE
BARCODE
LABEL
BOX
SL01305
Figure 4. Tape and reel packing method
6
2001 Oct 03
Philips Semiconductors
Product data
300 mA LDO with ON/OFF control and
independent delayed RESET function
SA57026
SOP-7B: small outline 7-pin surface mount package
5.0± 0.3
1.67 ±0.2
5
7
±
4.4 0.2
PIN #1
4
1.27
0.895 MAX
1.55± 0.15
0.05± 0.05
0.10
±
0.4 0.1
0.12
NOTE
1. Controlling dimensions are in millimeters (mm).
7
2001 Oct 03
Philips Semiconductors
Product data
300 mA LDO with ON/OFF control and
independent delayed RESET function
SA57026
Data sheet status
Product
status
Definitions
[1]
Data sheet status
[2]
Objective data
Development
This data sheet contains data from the objective specification for product development.
Philips Semiconductors reserves the right to change the specification in any manner without notice.
Preliminary data
Product data
Qualification
Production
This data sheet contains data from the preliminary specification. Supplementary data will be
published at a later date. Philips Semiconductors reserves the right to change the specification
without notice, in order to improve the design and supply the best possible product.
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply.
Changes will be communicated according to the Customer Product/Process Change Notification
(CPCN) procedure SNW-SQ-650A.
[1] Please consult the most recently issued data sheet before initiating or completing a design.
[2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest
information is available on the Internet at URL http://www.semiconductors.philips.com.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Righttomakechanges—PhilipsSemiconductorsreservestherighttomakechanges, withoutnotice, intheproducts, includingcircuits,standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Copyright Philips Electronics North America Corporation 2001
All rights reserved. Printed in U.S.A.
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Date of release: 10-01
Document order number:
9397 750 08968
Philips
Semiconductors
相关型号：
SA57026FD
IC VREG 3.3 V FIXED POSITIVE LDO REGULATOR, 0.3 V DROPOUT, PDSO7, 4.40 MM, PLASTIC, SOP-7, Fixed Positive Single Output LDO Regulator
NXP
©2020 ICPDF网 联系我们和版权申明