SAA1501 [NXP]
Battery charge level indicator; 电池电量指示
| 型号： | SAA1501 |
| 厂家： | 
NXP |
| 描述： | Battery charge level indicator |
| 文件： | 总20页 (文件大小：374K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
DATA SHEET
SAA1501T
Battery charge level indicator
December 1994
Objective specification
File under Integrated Circuits, IC11
Philips Semiconductors
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
FEATURES
GENERAL DESCRIPTION
• High level of integration to allow assembly in intelligent
battery packs
The SAA1501T is intended to be used as a battery monitor
and charge current control circuit in rechargeable battery
systems.
• Accurate charge and discharge account
The SAA1501T is processed in BiCMOS technology
where the benefits of mixed bipolar and CMOS technology
is fully utilized to achieve high accuracy measurements
and digital signal processing in the same device. The
general function of the integrated circuit is a Coulomb
counter. During battery charging, the charge current and
charge time are registered in a Coulomb counter. During
discharge, the discharge current and time are recorded.
The momentary charge amount of the batteries can be
displayed either on an LCD screen or on an LED bargraph.
Using the SAA1501T, intelligent batteries or intelligent
battery powered systems can be easily designed with only
a few external components.
• Large dynamic range of charge and discharge currents
• Independent settings of charge and discharge efficiency
• 2 V minimum supply voltage (2 cell operation)
• Temperature protection of batteries during charging
• Temperature controlled self-discharge
• Accurate charge current regulation
• Two charge amount display modes, LCD and LED.
QUICK REFERENCE DATA
SYMBOL
VCC
PARAMETER
supply voltage
CONDITIONS
MIN.
2.0
TYP.
3.0
MAX.
4.3
UNIT
V
ICC
supply current
VCC = 3 V;
Ic = Id = 60 µA
−
−
−
1.2
1.7
100
−
mA
ICCstb
fosc
supply current in standby mode
fixed oscillator frequency
VCC = 3 V;
VCSI = VDSI = 0 V
−
µA
Cosc = 820 pF;
4.2
kHz
Rref = 51.5 kΩ
Vi(s)
input sense voltage (pins 9 and 10)
operating ambient temperature
0
0
−
−
V
CC − 1.6 V
Tamb
+70
°C
ORDERING INFORMATION
PACKAGE
TYPE NUMBER
NAME
DESCRIPTION
VERSION
SAA1501T
SO24
plastic small outline package; 24 leads; body width 7.5 mm
SOT137-1
December 1994
2
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
BLOCK DIAGRAM
December 1994
3
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
PINNING
SYMBOL PIN
DESCRIPTION
supply voltage
VCC
EN
Ccy
CCC
Ich
1
2
3
4
5
enable output
duty cycle capacitor output
charge counter capacitor output
maximum average charge current
setting input
Rref
6
7
current reference resistor input
RDCC
discharge current conversion resistor
input
RCCC
8
charge current conversion resistor
input
CSI
9
charge sense input
DSI
10 discharge sense input
RTEMP1
RTEMP2
Cosc
BUZ
FULL
L100
L80
11 temperature sensing resistor 1 input
12 temperature sensing resistor 2 input
13 oscillator capacitor input
14 buzzer output
15 battery full indication output
16 100% segment indication output
17 80% segment indication output
18 60% segment indication output
19 40% segment indication output
20 20% segment indication output
21 LCD back plane drive
L60
L40
L20
BP
BLI
22 battery low indicator LED output
23 power-on LED output
POL
GND
Fig.2 Pin configuration.
24 power ground
December 1994
4
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
FUNCTIONAL DESCRIPTION
Protections
The most important function of the SAA1501T is the
charge account in rechargeable battery systems. Both
NiCd and NiMH batteries in all sizes can be used. The
system can operate alone as a charge monitor with a
charge amount display function or, can operate in
conjunction with a charger. If the SAA1501T operates
together with a charger, it delivers a control signal at output
EN, for charge current regulation or for battery voltage
regulation.
In the temperature control block, the absolute temperature
is used as a protection to end the fast charge cycle. Fast
charging at high temperature is not permitted because of
degradation of the battery cells. If the batteries are
disconnected, an open-battery condition is recognized and
the SAA1501T enters the standby mode.
Mode detection
The mode detector detects whether there are any charge
or discharge currents, whether the system is powered,
whether loads are connected or whether the system is in
the standby mode. If power is connected, the power-on
LED (POL) is on. In the standby mode, the Coulomb
counter will count down in accordance with the
self-discharge speed of the batteries, which is temperature
controlled. The following subsections describe the various
blocks of the block diagram in more detail.
Fast charging systems and charge current regulation
The SAA1501T is especially designed to be used in fast
charging systems. In fast charging systems, the charge
time is lowered by raising the charge current. Signal EN
controls the charger current. The counters register the
state of charge of the batteries and at the 80% level the
charge current is reduced via a smaller duty cycle
regulation of signal EN. The second (slow) level fully
charges the batteries which is not possible with the first
(fast) level. After the slow charge mode the counter
switches over to an even smaller duty cycle of EN and thus
enters the third (trickle) charge mode, to overcome the
self-discharge of the batteries.
Supply and reference
During the period when VCC rises from 0 V to the internal
reset level, all counters are reset. The internal reset is
released before VCC reaches 1.7 V. The operating supply
voltage ranges from 2 V to the open battery level of
4.3 V (min). The characteristics are guaranteed at
Current sensing and charge account
VCC = 3 V. In order to protect the SAA1501T against high
The charge current is sensed by means of a very low
resistance (e.g. 70 mΩ) sense resistor Rsc (see Fig.8) to
save power at high charge rates. Via the V/I charge
converter and external resistor RCCC (see Fig.8), the
sensed voltage is converted into a charge current Ic (the
same is applicable for the discharge current). In the I/F
converter the charge current is converted into a frequency
for up-counting the counter. For the discharge current (Id)
the converted frequency is used for down-counting. The
up and down counting is registered in counters CNT1 and
CNT2, depending on the actual charge and discharge
current levels of the batteries. This is called dynamic
charge account.
supply voltages during open battery in a flyback converter,
a voltage clamp circuit is made active at 6.35 V (typ). The
clamping current must not exceed 80 mA. A band gap
reference block is included to generate accurate voltages
i.e. for the oscillator. Moreover, together with Rref, accurate
currents are generated which are used in the I/F and V/I
converters and the oscillator block. In the standby mode
only the oscillator and the digital parts are active to limit the
discharge current of the batteries to a current level of less
than 100 mA. The circuits that are needed temporarily are
switched on and off during standby (see “Timing
characteristics” tsom).
Voltage-to-current charge and discharge
Charge display
In the V/I converter, the input charge current is translated
into acceptable levels for the circuit. The conversion
formula is:
The charge amount represented by the Coulomb counter
can be displayed via an LCD screen or via an LED
bargraph. If the charge amount is reduced to 0%, the
battery low indicator (BLI) LED is turned on at the end of a
battery discharge session. A flashing BLI, in combination
with a repeating buzzer alarm, informs the user about the
low charge state. A new charge session should then be
started.
(Icharge × Rsc
)
Ic
=
; where RCCC > Rsc (see Fig.7)
---------------------------------------
RCCC
December 1994
5
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
With RCCC, the charge efficiency can be manipulated
depending on the charge level. The restriction of the
SAA1501T is a maximum average charge current of 60 µA
and a minimum momentary charge current of 0.6 µA. The
same formula is applicable for the discharge current. The
discharge efficiency can now also be changed by RDCC
depending on the discharge current levels, but
independent of the charge current. As both sense levels
are referenced to ground, the sensing elements could be
combined into one. The outputs are used combined as
1⁄6 × (Ic − Id) in the I/F converter and combined as (Ic − Id)
in the pulse width modulator block and made separately
available in the mode detector. The conversion is made
lower by a factor of 6 in the I/F converter block, thereby
enabling the use of poor leakage capacitors on pin 4. All
V/I converter pins are sensitive to capacitive loading
(Cout × Rconv < 1 ms), the conversion resistors should be
mounted as close as possible to the output pins.
to the trickle charge mode to overcome the self-discharge
of the batteries. The top-up charge volume of
CNT2 = 0.2 × CNT1 = 0.2 C (where Q is rated as Ampere
hours of the battery). The slow and trickle charge current
levels are dependent on the k-factor. Signal EN controls
the external charger e.g. TEA1400 (see Fig.8). When an
LED bargraph display is used, the LED currents are also
considered as a battery discharge current, and therefore
influence the duty cycle of the charge current regulation
signal EN. The SAA1501T also enables temperature
protection. In the event that the battery temperature
exceeds a certain maximum temperature level
(Tbattery > Tmax), which can be set by an external NTC
resistor, the SAA1501T switches to the slow charge mode.
In the standby mode (self-discharge mode), which is
recognized by the SAA1501T in the mode detector when
both the charge and discharge currents are zero
(Ic = Id = 0), the self-discharge of the batteries is registered
by counting down in 200 days (based on fosc = 4 kHz) if
Tbattery < Tself or in 100 days (based on fosc = 4 kHz) if
Tbattery > Tself. Tself is also set by means of an external NTC
resistor.
I/F converter
This block produces up-counts while charging and
down-counts while discharging. The I/F converter
translates the charge/discharge currents into a frequency.
This frequency is determined by
Band gap generation
From the band gap voltage block, two reference voltages
are derived Vref and Vmax. Voltage Vref at pin Rref sets the
reference currents, Iref1 (I/F converter); Iref2 (mode
detector) and Iref3 (oscillator). Voltage Vmax sets the
current Imax which is used in the pulse width modulation
block to accurately control the charge current.
(I c (d) × Rsense × 6 )
f =
-----------------------------------------------------------------------------------
(C CC × ∆Vosc × RCCC (RDCC)
)
During the time period ‘t’, the charge current, expressed as
a ‘Charge Parcel’, will be counted in the Coulomb counters
(CNT1 and CNT2). During discharge the ‘Charge Parcel’ is
the product of the discharge current and the ‘t’ from the I/F
converter generated frequency. The momentary contents
of the Coulomb counter is a multiple of the ‘Charge
Parcels’.
Charge current regulation
While charging, the SAA1501T produces a charge current
regulation signal EN in the pulse width modulation block
which is used for controlling an external charger. This
digital signal EN is derived from the signal produced at pin
Ccy. The duty cycle is determined by
Coulomb counters CNT1 and CNT2
The SAA1501T has been designed for average maximum
charge and discharge current levels of 5 C and minimum
charge and discharge current levels of 0.05 C. This means
that counter CNT1 will be full, or empty, after a minimum
time period of 12 minutes at maximum charge and
discharge currents at the recommended oscillator
k × Imax
δ =
-------------------
Ic – Id
in which the value of k depends on the state of the
counters CNT1 and CNT2:
frequency. Higher charge and discharge rates than 5 C
are possible, but only by changing the oscillator frequency.
It should be noted that the self-discharge time and the
display functions are influenced by a higher oscillator
frequency. The SAA1501T enables top-up charging in
order to account for the decrease of charge efficiency at
high charge rates. The SAA1501T switches to the slow
charge mode at full recognition when CNT1 is at its
maximum. As soon as the batteries are completely full
(when CNT2 is at its maximum), the SAA1501T switches
CNT1 is not full; k = 1 (fast charging).
CNT1 is full; CNT2 is not full; k = 0.1 (slow charging).
CNT1 and CNT2 are full; k = 0.025 (trickle charging).
December 1994
6
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
Mode detector
Prescaler/controller
This block differentiates between the available modes of
operation. The modes are given below:
In the prescaler, a new system clock is created (CLK)
which is used for all timing blocks. Many frequencies are
derived from the basic oscillator at the standard frequency
of 4 kHz (1/Tosc), such as the self-discharge times and the
modulation frequency for the buzzer, the drive voltage
frequency for the LCD screen and the pulse trains for
temperature measurements and power/load sensing
measurements in the mode detector.
Charge mode; power charge (POCH).
Discharge mode; battery load (BATLD).
Power load mode (POLD); the batteries are charged
while the load is also active.
Self discharge mode; (STANDBY).
To detect power in a regulated system (see Fig.8) the EN
signal is used for sensing. The POCH mode is recognized
when the converted charge current Ic > Iref2 (when in the
power mode, change of mode can only be recognised if
EN is HIGH). The BATLD mode is recognized when
Id > Iref2; the POLD mode is recognized when Ic > Iref2 and
Id > Iref2; the standby mode is recognized when Ic < Iref2
and Id < Iref2. In the standby mode, if the advised frequency
(4 kHz) is applied, it takes 0.5 s to determine another
mode (in all other modes, a change of mode is sensed
continuously). In all other modes an eventual change of
mode is done continuously. To save supply current during
standby, the V/I converters are switched off. With the
specific fixed intervals, the SAA1501T checks whether
power or load is connected again. This checking is
synchronized by the sensing signal of the V/I converters.
The SAA1501T can handle a DC charge current as well as
a discontinuous charge current (SMSP charger). The load
current can also be DC or interrupted, e.g. produced by a
motor. The digital filtering of both signals, to overcome
faulty mode detections, restricts the conditions in which
power and load are recognized. Because of the very
sensitive input detection level of the mode detector for a
charge current (power) in combination with the high
interference levels of motor driving, the detection level for
power (Ic > Iref2) is raised by a factor of 25 when the
batteries are loaded.
Temperature
In the temperature control block two temperature
measurements are performed. In order to switch off fast
charging when the battery temperature exceeds an
adjustable maximum temperature (Tmax), a maximum
temperature measurement is performed. A second
temperature measurement is performed in the standby
mode. This temperature measurement is input to the
temperature control block to switch over the self-discharge
rate from a count down of 200 days (based on fosc = 4 kHz)
if Tbattery < Tself, to a count down rate of 100 days (based
on fosc = 4 kHz) if Tbattery > Tself. In all modes the
temperature is measured periodical. The temperature
circuit which controls the above mentioned functions is a
bridge configuration synthesis, as illustrated in Fig.3.
Oscillator
As the oscillator has to operate in all modes, including the
standby mode, the current consumption of the oscillator
must be very low. The same applies for the band gap
generator block, because the band gap delivers accurate
reference voltages and currents to the oscillator block.
Apart from the low current consumption, the accuracy of
the period time is important. The period time of the
oscillator is:
(VH – VL)
tosc = 2 × Cosc
×
= 5.6 × Cosc × Rref
--------------------------
Fig.3 Temperature circuit.
Iref3
December 1994
7
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
The BLI sequence is as follows. If during discharge the
charge state falls below 0%, the red BLI LED is turned on.
Changing mode from discharge to standby means that the
BLI LED and the buzzer (BUZ) are activated as indicated
in Fig.4. If after a 0% passing recharge is activated, the red
BLI LED is turned on again for as long as the counter
remains below 10%. Switch-over in the 0 to 10% range to
standby will activate BLI and BUZ again.
Display decoder driver
The counters are used to output the battery charge
amount via a decoder and driver stage to the display
outputs L100, L80, L60, L40 and L20 to drive an LCD
screen or an LED bargraph. A 64 Hz (based on
fosc = 4 kHz) block signal at output BP (back plane) must
be connected to the back plane of the LCD bar. If pin BP
is connected to ground, the display outputs L20 to L100
will produce signals for an LED bargraph. Output signal
POL (power-on LED) indicates when the batteries are in
the charge mode. When the counter is not at its maximum
state, POL is on and flickers at 2 Hz (based on
fosc = 4 kHz) when the counter is at its maximum. The
waveforms illustrated in Fig.4 depict operation of the
monitor display. The outputs BLI (battery low indication),
BUZ (buzzer) and FULL indicate the extreme status
(empty or full) of the counters and the batteries. The
waveforms of the signals BLI and BUZ if one switches over
from BATLD to standby when BLI is active, are given in
Fig.4.
The LEDs of the LED bargraph are activated as a result of
each operational mode change, starting with a step-up
pattern. Step-up means that LEDs are activated
successively one after the other, in accordance with the
charge status each 1⁄8 s (based on fosc = 4 kHz). After the
step-up, the LEDs will be on for 8 s (based on
fosc = 4 kHz), except for the POCH mode, where the LEDs
will be on continuously to inform the user about the charge
state of the batteries. The LCD display is, apart from the
LED mode, always visible.
Figure 5 shows the legend for Fig.6. Figure 6 shows the
operation of the monitor display.
BUZ
Fig.4 BLI and buzzer timing.
December 1994
8
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
a test pin. Raising the voltage above 1 V during the set-up
time will activate the test. The test mode can only be
started in the standby mode. In the test mode all counters
are reset and will be active successively in the sequence
BLI, L20, L40, L60, L80, L100 and FULL with an interval
period determined by Tosc. The test mode can be exited via
the following methods:
Open battery protection
Open battery protection is active when VCC = 4.5 V (typ.).
The SAA1501T will then react as if the system is in the
standby mode. This means that the LEDs are turned off in
the LED mode, in the LCD mode the flickering is stopped
and the enable pin (EN) is switched to floating.
Power-on; the Coulomb counter retains the latest data
displayed.
Testing
A user test facility is built-in for checking if the LCD and/or
LED displays are mounted correctly. Pin RCCC is used as
Automatically after the test cycle time; the Coulomb
counter is reset.
Fig.5 Legend for Fig.6.
December 1994
9
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
Fig.6 Charge state of counter shown by LCD or LED display.
December 1994
10
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134). All voltages with respect to GND (pin 24); input
currents are positive; pins 5, 6 and 21 are not allowed to be voltage driven; the voltage ratings are valid provided other
ratings are not being violated.
SYMBOL
VCC
PARAMETER
supply voltage
CONDITIONS
MIN.
−0.5
MAX.
+5.5
UNIT
V
V
V
Vn1
Vn2
input voltage at pins 9 to 12
−0.5
−0.5
+1.0
VCC
input voltage at pins 2 to 4, 13 to 20, 22
and 23
∆V
voltage difference between pins 10 and
7 and between pins 9 and 8
−2.0
+2.0
V
ICC
IGND
In
supply current
−
80
mA
mA
mA
W
power ground supply current
supply current at pins 5 to 8
total power dissipation
storage temperature
−
−80
−1
−
Ptot
Tstg
Tj
Tamb = 70 °C
−
0.75
+150
+150
+75
−55
−
°C
junction temperature
°C
Tamb
operating ambient temperature
−10
°C
QUALITY SPECIFICATION
In accordance with SNW-FQ-611 part E. The numbers of the quality specification can be found in the “Quality Reference
Handbook”. The Handbook can be ordered using the code 9398 510 63011.
THERMAL CHARACTERISTICS
SYMBOL
Rth j-a
PARAMETER
VALUE
UNIT
thermal resistance from junction to ambient in free air
75
K/W
December 1994
11
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
CHARACTERISTICS
VCC = 3 V; Tamb = 25 °C; Rref = 51.5 kΩ (0.1%); Cosc = 820 pF (0.1%); RCCC = RDCC = 3.65 kΩ (0.1%); Rmax = 3.48 kΩ
(0.1%); Iref = Vref/Rref; Imax = Vmax/Rmax; the minimum and maximum values are 4 sigma limits; unless otherwise
specified.
SYMBOL
Supply
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
VCC
supply voltage
note 1
2.0
3.0
4.3
V
VCC(ir)
supply voltage internal
reset
−
1.2
1.7
V
ICC
supply current
Ic = Id = 60 µA
0.6
−
−
1.7
mA
mA
ICCstb
supply current in standby VCSI = VDSI = 0 V
mode
−
100
Vref
Iref
reference voltage
reference current
maximum voltage
note 2
204
3.5
204
0
211
−
217
8
mV
µA
notes 1 and 2
note 2
Vmax
TC
211
217
mV
temperature coefficient of T = 0 to 100 °C
25 × 10−6 100 × 10−6 °C
reference voltage
Vclamp
clamping level voltage
ICC = 50 mA
5.8
6.3
6.8
V
Voltage-to-current charge/discharge
I4
voltage-to-current
charge/discharge current
accuracy
V9 = 7 mV; V4 = 1.5 V
V10 = 7 mV; V4 = 1.5 V
V9 = 200 mV; V4 = 1.5 V
V10 = 200 mV; V4 = 1.5 V
−259
262
−324
328
−389
394
nA
nA
µA
µA
µA
−8.93
8.93
−9.13
9.13
−9.32
9.32
I3
voltage-to-current
V9 = 7 mV; Rmax = 400 kΩ; −1.55
−1.94
−2.32
charge/discharge current k = 0.025
accuracy
V
10 = 7 mV; Rmax = 400 kΩ; 1.57
1.97
−54.7
54.7
1.0
2.36
−56
56
µA
µA
µA
%
k = 0.025
V9 = 200 mV;
Rmax = 400 kΩ; k = 0.025
−53.5
53.5
−
V10 = 200 mV;
Rmax = 400 kΩ; k = 0.025
I4/I3
relative current accuracy V9 = V10 = 200 mV
2.5
of voltage-to-current in
charge counter capacitor
Vi(s)
input sense voltage at
pins 9 and 10
VCC(max) = 3.7 V; note 1
3.7 < VCC < 4.4 V; note 1
0
−
−
−
V
CC − 1.6
V
−
2.1
60
V
Io(s)
Vos
DC output sense current
(pins 8 and 7)
0.6
µA
offset voltage
−
−
1.8
mV
December 1994
12
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
I/F converter
a
multiplication factor for
Iref1
Iref1 = a × Iref
(where a is constant);
V4 = 1.26 V; idle mode
2.35
2.5
2.65
Vclamp
clamping voltage (pin 4)
Ic = 0; Id = 60 µA;
I4 = 10 µA
0.7
0.9
1.1
V
VCCC(H)
VCCC(L)
HIGH level reference
voltage (pin 4)
1.58
1.26
1.66
1.33
1.74
1.4
V
V
LOW level reference
voltage (pin 4)
Pulse width modulator
ACC
Imax
accuracy for Imax at Ccy
15 < Imax < 60 µA
−
−
±3
%
maximum DC current
k factor
Imax = Vmax/Rmax; note 1
0.6
−
60
mA
Id/Imax
k = 1; Vd = 1.5 V; idle mode 0.95
0.98
0.099
1.01
0.104
k = 0.1; Vd = 1.5 V; idle
mode
0.094
0.023
0.7
k = 0.025; Vd = 1.5 V;
idle mode
0.025
0.9
−
0.027
1.1
VCCY
VCCY
start up-clamping voltage Id = 10 µA; Ic = 0
(pin 3)
V
V
clamping voltage (pin 3)
open-circuit at pin 3;
pin 5 = VCC
−
VCC − 0.6
;
±(Ic − Id) = 60 µA
VCCY(H)
VCCY(L)
HIGH level switching
voltage
1.60
1.28
−
1.77
1.32
−
1.86
1.37
1
V
LOW level switching
voltage
V
IZ
3-state enable current
V2 = 1.5 V
µA
Mode detector
Iref2
mode detection level at
pins 7 and 8
I
ref2 ≥ e × Iref
(where e is constant)
ref4 ≥ Iref2
in modes POLD and BATLD
−
−
0.15Iref
25Iref2
−
−
Iref4
mode detection level at
pin 7
I
;
Oscillator (pin 13)
Qc
Qd
∆Q
charge amount
I
ref1(sink) × Tclk
142
142
0.95
150
150
1.0
158
158
1.05
nC
nC
discharge amount
Iref1(source) × Tclk
difference between
charge and discharge
charge amount
b
multiplication factor for
Iref3
Iref3 = b × Iref
(where b is constant)
−
−
0.75
440
−
−
∆Vosc
voltage swing
mV
HIGH-to-LOW transition
December 1994
13
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
SYMBOL
fosc
PARAMETER
CONDITIONS
MIN.
3.9
TYP.
4.3
MAX.
4.7
UNIT
kHz
oscillator frequency
Temperature control (pins 11 and 12)
Vi input voltage
0
−
900
10.3
17
mV
ITEMP2/ITEMP1 detection at Tmax
ITEMP2/ITEMP1 detection at Tself
V11 = V12 = 300 mV
V11 = V12 = 300 mV
9.7
15
10.0
16
c
multiplication factor for
ITEMP1 = c × Iref
0.45
0.54
0.63
ITEMP1
(where c is constant);
VTEMP1 = VTEMP2 = 300 mV
d
multiplication factor for
ITEMP2
ITEMP2 = d × Iref
(where d is constant);
VTEMP1 = VTEMP2 = 300 mV
4.5
5.4
6.3
Open battery protection
VCC(ob)
Testing
Vtest
open-battery level voltage
4.3
1.0
7
4.5
−
4.65
2.0
12
V
test level voltage
V
Display decoder driver
IOL1 LOW level output current
VOL = 0.6 V; L40 to L100 off;
10
mA
(pin 20 LED),
(LED 20 is on)
VCC = 2.4 V
IOBP
output LED sense current
(pin 21 LED),
V
OBP = 0.1 V; L40 to L100
63
82
100
µA
off; VCC = 2.4 V
(LED 20 is on)
ILED(CF)
IOL2
LED current
compensation factor
IOL1/IOBP; VCC = 2.4 V
110
7.5
121
11
132
14
LOW level output current all LEDs on; VOL = 0.7 V;
mA
(pins 20 to 16 LED),
(all LEDs are on)
VCC = 2.8 V
IOBP(tot)
ILED(CF)
IOL
total output sense current VOBP = 0.1 V; VCC = 2.8 V;
350
115
350
0.9
7
452
125
480
1.2
560
135
640
1.7
µA
(pins 21)
L20 to L100 on
LED current
5IOL2/IOBP(tot)
compensation factor
output current
VOL = 0.5 V; VCC = 2.8 V
µA
mA
mA
µA
µA
µA
(pins 20 to 16 LCD)
IOL(14,15)
IOL(22,23)
IOL(21)
IOH
LOW level output current VOL = 0.4 V; VCC = 2.4 V
(pins 14 and 15)
LOW level output current VOL = 0.4 V; VCC = 2.1 V
(pins 22 and 23 LED)
10
12
LOW level output current VOL = 0.4 V; VCC = 2.8 V
(pin 21 LCD)
572
261
239
849
378
378
1214
526
565
HIGH level output current VOH = 2.4 V; VCC = 2.8 V
(pins 20 to 16 LED)
IOH(21)
HIGH level output current VOH = 2.4 V; VCC = 2.8 V
(pin 21 LED)
December 1994
14
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
SYMBOL
VOH(14)
PARAMETER
CONDITIONS
MIN.
0.7
TYP.
1.6
MAX.
2.5
UNIT
µA
HIGH level output current VOH = 2 V; VCC = 2.4 V
(pin 14)
IOH(15)
IOH(22,23)
ILO
HIGH level output current VOH = 2 V; VCC = 2.4 V
(pin 15)
0.99
260
−
1.67
450
−
2.69
708
±1
mA
µA
µA
HIGH level output current VOH = 2.4 V; VCC = 2.4 V
(pins 22 and 23)
output leakage current
(pin 21)
VOH = 0 to VCC
Notes
1. Not measured by the industrial measuring program, but guaranteed by design.
2. Internally detected from band gap generator.
December 1994
15
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
TIMING CHARACTERISTICS
SYMBOL
Tosc
PARAMETER
oscillator cycle time
clock cycle time
CONDITIONS
VALUE
note 1
Tosc = 2Cosc × Vosc/Iref3
Tclk
64tosc
tsom
sense operation mode time
note 2
note 2
1.5 × 27Tosc
212Tosc
tsom(p)
sense operation mode period
time
trec
recognition time
power; note 3
load; note 4
>32tosc
>20tosc
235Tosc
tself
self discharge counter time
Tbattery > Tself
(100 days at fosc = 4 kHz)
Tbattery > Tself
(200 days at fosc = 4 kHz)
236Tosc
27Tosc
tbattery(s)
tbattery(p)
battery temperature
measurement sense time
battery temperature
216Tosc
measurement period time
tsu
display test set-up time
interval display test time
period display test time
LED set-up time
211Tosc < t < 1.5 × 218Tosc
210Tosc
1.5 × 218Tosc
29Tosc
tid
tpd
tsu:LED
tLED(ON)
LEDs-on time
after change of mode
(except POCH mode)
215Tosc
fBP
drive voltage frequency for back
plane
2−4Tosc
fBUZ
modulation frequency for auto
buzzer
1⁄2Tosc
Notes
V
1. tosc = 2Cosc
×
osc ; where Vosc = 440 mV and Iref3 = 0.75.
-----------
Iref3
2. Applies to all converters and enable signal.
3. For charge current AC or DC: f > 1⁄2fosc
.
4. For discharge current AC: f > 1⁄4fosc
.
December 1994
16
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
APPLICATION INFORMATION
Fig.7 Battery pack application diagram; with camcorder.
Fig.8 State-of-charge indicator and charge current regulation.
17
December 1994
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
PACKAGE OUTLINE
15.6
15.2
7.6
7.4
A
10.65
10.00
0.1 S
S
0.9
0.4
(4x)
24
13
1.1
1.0
2.45
2.25
2.65
0.3
0.1
0.32
2.35
0.23
pin 1
index
1.1
0.5
o
0 to 8
1
12
detail A
MBC235 - 1
0.49
0.36
0.25 M
(24x)
1.27
Dimensions in mm.
Fig.9 Plastic small outline package; 24 leads; body width 7.5 mm (SO24; SOT137-1).
December 1994
18
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
applied to the substrate by screen printing, stencilling or
pressure-syringe dispensing before device placement.
SOLDERING
Plastic small-outline packages
BY WAVE
Several techniques exist for reflowing; for example,
thermal conduction by heated belt, infrared, and
vapour-phase reflow. Dwell times vary between 50 and
300 s according to method. Typical reflow temperatures
range from 215 to 250 °C.
During placement and before soldering, the component
must be fixed with a droplet of adhesive. After curing the
adhesive, the component can be soldered. The adhesive
can be applied by screen printing, pin transfer or syringe
dispensing.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 min at 45 °C.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder bath is
10 s, if allowed to cool to less than 150 °C within 6 s.
Typical dwell time is 4 s at 250 °C.
REPAIRING SOLDERED JOINTS (BY HAND-HELD SOLDERING
IRON OR PULSE-HEATED SOLDER TOOL)
Fix the component by first soldering two, diagonally
opposite, end pins. Apply the heating tool to the flat part of
the pin only. Contact time must be limited to 10 s at up to
300 °C. When using proper tools, all other pins can be
soldered in one operation within 2 to 5 s at between 270
and 320 °C. (Pulse-heated soldering is not recommended
for SO packages.)
A modified wave soldering technique is recommended
using two solder waves (dual-wave), in which a turbulent
wave with high upward pressure is followed by a smooth
laminar wave. Using a mildly-activated flux eliminates the
need for removal of corrosive residues in most
applications.
For pulse-heated solder tool (resistance) soldering of VSO
packages, solder is applied to the substrate by dipping or
by an extra thick tin/lead plating before package
placement.
BY SOLDER PASTE REFLOW
Reflow soldering requires the solder paste (a suspension
of fine solder particles, flux and binding agent) to be
DEFINITIONS
Data sheet status
Objective specification
Preliminary specification
Product specification
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
December 1994
19
Philips Semiconductors – a worldwide company
Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428)
BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Pakistan: Philips Electrical Industries of Pakistan Ltd.,
Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton,
KARACHI 75600, Tel. (021)587 4641-49,
Fax. (021)577035/5874546.
Tel. (02)805 4455, Fax. (02)805 4466
Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. (02)810 0161, Fax. (02)817 3474
Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213,
Tel. (01)60 101-1236, Fax. (01)60 101-1211
Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands,
Portugal: PHILIPS PORTUGUESA, S.A.,
Tel. (31)40 783 749, Fax. (31)40 788 399
Rua dr. António Loureiro Borges 5, Arquiparque - Miraflores,
Apartado 300, 2795 LINDA-A-VELHA,
Tel. (01)4163160/4163333, Fax. (01)4163174/4163366.
Brazil: Rua do Rocio 220 - 5th floor, Suite 51,
CEP: 04552-903-SÃO PAULO-SP, Brazil.
P.O. Box 7383 (01064-970).
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. (65)350 2000, Fax. (65)251 6500
South Africa: S.A. PHILIPS Pty Ltd.,
Tel. (011)821-2333, Fax. (011)829-1849
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS:
Tel. (800) 234-7381, Fax. (708) 296-8556
Chile: Av. Santa Maria 0760, SANTIAGO,
195-215 Main Road Martindale, 2092 JOHANNESBURG,
P.O. Box 7430 Johannesburg 2000,
Tel. (011)470-5911, Fax. (011)470-5494.
Tel. (02)773 816, Fax. (02)777 6730
Colombia: IPRELENSO LTDA, Carrera 21 No. 56-17,
77621 BOGOTA, Tel. (571)249 7624/(571)217 4609,
Fax. (571)217 4549
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. (032)88 2636, Fax. (031)57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. (9)0-50261, Fax. (9)0-520971
France: 4 Rue du Port-aux-Vins, BP317,
92156 SURESNES Cedex,
Tel. (01)4099 6161, Fax. (01)4099 6427
Germany: P.O. Box 10 63 23, 20043 HAMBURG,
Tel. (040)3296-0, Fax. (040)3296 213.
Greece: No. 15, 25th March Street, GR 17778 TAVROS,
Tel. (01)4894 339/4894 911, Fax. (01)4814 240
Hong Kong: PHILIPS HONG KONG Ltd., 6/F Philips Ind. Bldg.,
24-28 Kung Yip St., KWAI CHUNG, N.T.,
Spain: Balmes 22, 08007 BARCELONA,
Tel. (03)301 6312, Fax. (03)301 42 43
Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM,
Tel. (0)8-632 2000, Fax. (0)8-632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. (01)488 2211, Fax. (01)481 77 30
Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West
Road, Sec. 1. Taipeh, Taiwan ROC, P.O. Box 22978,
TAIPEI 100, Tel. (02)388 7666, Fax. (02)382 4382.
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong,
Bangkok 10260, THAILAND,
Tel. (662)398-0141, Fax. (662)398-3319.
Turkey:Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. (0212)279 2770, Fax. (0212)269 3094
United Kingdom: Philips Semiconductors LTD.,
276 Bath road, Hayes, MIDDLESEX UB3 5BX,
Tel. (081)73050000, Fax. (081)7548421
United States:811 East Arques Avenue, SUNNYVALE,
CA 94088-3409, Tel. (800)234-7381, Fax. (708)296-8556
Uruguay: Coronel Mora 433, MONTEVIDEO,
Tel. (852)424 5121, Fax. (852)428 6729
India: Philips INDIA Ltd, Shivsagar Estate, A Block ,
Dr. Annie Besant Rd. Worli, Bombay 400 018
Tel. (022)4938 541, Fax. (022)4938 722
Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4,
P.O. Box 4252, JAKARTA 12950,
Tel. (02)70-4044, Fax. (02)92 0601
Tel. (021)5201 122, Fax. (021)5205 189
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. (01)640 000, Fax. (01)640 200
For all other countries apply to: Philips Semiconductors,
International Marketing and Sales, Building BE-p,
P.O. Box 218, 5600 MD, EINDHOVEN, The Netherlands,
Telex 35000 phtcnl, Fax. +31-40-724825
Italy: PHILIPS SEMICONDUCTORS S.r.l.,
Piazza IV Novembre 3, 20124 MILANO,
Tel. (0039)2 6752 2531, Fax. (0039)2 6752 2557
Japan: Philips Bldg 13-37, Kohnan2-chome, Minato-ku, TOKYO 108,
SCD35
© Philips Electronics N.V. 1994
Tel. (03)3740 5028, Fax. (03)3740 0580
Korea: (Republic of) Philips House, 260-199 Itaewon-dong,
All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
Yongsan-ku, SEOUL, Tel. (02)794-5011, Fax. (02)798-8022
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,
SELANGOR, Tel. (03)750 5214, Fax. (03)757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TX 79905,
Tel. 9-5(800)234-7381, Fax. (708)296-8556
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB
The information presented in this document does not form part of any quotation
or contract, is believed to be accurate and reliable and may be changed without
notice. No liability will be accepted by the publisher for any consequence of its
use. Publication thereof does not convey nor imply any license under patent- or
other industrial or intellectual property rights.
Tel. (040)783749, Fax. (040)788399
Printed in The Netherlands
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. (09)849-4160, Fax. (09)849-7811
373061/1500/01/pp20
Date of release: December 1994
9397 743 50011
Norway: Box 1, Manglerud 0612, OSLO,
Tel. (022)74 8000, Fax. (022)74 8341
Document order number:
Philips Semiconductors
相关型号：
SAA1501TD-T
IC POWER SUPPLY MANAGEMENT CKT, PDSO24, 7.70 MM, PLASTIC, SOT137-1, SOP-24, Power Management Circuit
NXP
©2020 ICPDF网 联系我们和版权申明