SC28L92A1B-S [NXP]
IC 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQFP44, 10 X 10 MM, 1.75 MM HEIGHT, PLASTIC, SOT-307-2, QFP-44, Serial IO/Communication Controller;
| 型号： | SC28L92A1B-S |
| 厂家： | 
NXP |
| 描述： | IC 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQFP44, 10 X 10 MM, 1.75 MM HEIGHT, PLASTIC, SOT-307-2, QFP-44, Serial IO/Communication Controller 微控制器和处理器 串行IO控制器 通信控制器 外围集成电路 数据传输 PC 时钟 |
| 文件： | 总44页 (文件大小：287K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
SC28L92
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
Product specification
2000 Jan 21
Supersedes data of 1999 May 07
IC19 Data Handbook
Philips
Semiconductors
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
DESCRIPTION
• 16-bit programmable Counter/Timer
The SC28L92 is a pin and function replacement for the SCC2692
and SC26C92 operating at 3.3 or 5 volts supply with added features
and deeper FIFOs. Its configuration on power up is that of the
SC26C92. Its differences from the 2692 are: 16 character receiver, 16
character transmit FIFOs, watch dog timer for each receiver, mode
register 0 is added, extended baud rate and overall faster speeds,
programmable receiver and transmitter interrupts. (Neither the
SC26C92 nor the SCC2692 is being discontinued.)
• Programmable baud rate for each receiver and transmitter
selectable from:
– 28 fixed rates: 50 to 230.4k baud
– Other baud rates to MHz at 16X
– Programmable user-defined rates derived from a programmable
counter/timer
– External 1X or 16X clock
Pin programming will allow the device to operate with either the
Motorola or Intel bus interface. The bit 3 of the MR0a register allows
the device to operate in an 8 byte FIFO mode if strict compliance
with the SC26C92 FIFO structure is required.
• Parity, framing, and overrun error detection
• False start bit detection
• Line break detection and generation
The Philips Semiconductors SC28L92 Dual Universal Asynchronous
Receiver/Transmitter (DUART) is a single-chip CMOS-LSI
communications device that provides two full-duplex asynchronous
receiver/transmitter channels in a single package. It interfaces
directly with microprocessors and may be used in a polled or
interrupt driven system with modem and DMA interface.
• Programmable channel mode
– Normal (full-duplex)
– Automatic echo
– Local loop back
– Remote loop back
The operating mode and data format of each channel can be
programmed independently. Additionally, each receiver and
transmitter can select its operating speed as one of 28 fixed baud
rates; a 16X clock derived from a programmable counter/timer, or an
external 1X or 16X clock. The baud rate generator and counter/timer
can operate directly from a crystal or from external clock inputs. The
ability to independently program the operating speed of the receiver
and transmitter make the DUART particularly attractive for
dual-speed channel applications such as clustered terminal
systems.
– Multi-drop mode (also called ‘wake-up’ or ‘9-bit’)
• Multi-function 7-bit input port (includes IACKN)
– Can serve as clock or control inputs
– Change of state detection on four inputs
– Inputs have typically >100k pull-up resistors
– Change of state detectors for modem control
• Multi-function 8-bit output port
– Individual bit set/reset capability
Each receiver and transmitter is buffered by 8 or 16 character FIFOs
to minimize the potential of receiver overrun, transmitter underrun
and to reduce interrupt overhead in interrupt driven systems. In
addition, a flow control capability is provided via RTS/CTS signaling
to disable a remote transmitter when the receiver buffer is full.
– Outputs can be programmed to be status/interrupt signals
– FIFO status for DMA interface
• Versatile interrupt system
– Single interrupt output with eight maskable interrupting
conditions
Also provided on the SC28L92 are a multipurpose 7-bit input port
and a multipurpose 8-bit output port. These can be used as general
purpose I/O ports or can be assigned specific functions (such as
clock inputs or status/interrupt outputs) under program control.
– Output port can be configured to provide a total of up to six
separate interrupt outputs that may be wire ORed.
– Each FIFO can be programmed for four different interrupt levels
– Watch dog timer for each receiver
The SC28L92 is available in two package versions: a 44-pin PLCC
and 44-pin plastic quad flat pack (PQFP).
• Maximum data transfer rates:
1X – 1Mb/sec, 16X – 1Mb/sec
• Automatic wake-up mode for multi-drop applications
• Start-end break interrupt/status
• Detects break which originates in the middle of a character
• On-chip crystal oscillator
FEATURES
• Member of IMPACT family: 3.3 to 5.0 volt , –40°C to +85°C and
68K for 80xxx bus interface for all devices.
• Dual full-duplex independent asynchronous receiver/transmitters
• 16 character FIFOs for each receiver and transmitter
• Pin programming selects 68K or 80xxx bus interface
• Power down mode
• Receiver time-out mode
• Programmable data format
– 5 to 8 data bits plus parity
• Single +3.3V or +5V power supply
• Powers up to emulate SC26C92
– Odd, even, no parity or force parity
– - 1, 1.5 or 2 stop bits programmable in 1/16-bit increments
2
2000 Jan 21
853–2161 23016
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
ORDERING INFORMATION
INDUSTRIAL
= +3.3 +5V ±10%,
V
CC
DESCRIPTION
44-Pin Plastic Leaded Chip Carrier (PLCC)
44-Pin Plastic Quad Flat Pack (PQFP)
T
amb
= –40 to +85°C
DRAWING NUMBER
SC28L92A1A
SC28L92A1B
SOT187–2
SOT307-2
3
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
PIN CONFIGURATION DIAGRAM
80XXX PIN CONFIGURATION
44
34
6
40
1
7
39
1
33
23
PLCC
PQFP
11
29
17
18
28
12
22
Pin
1
Function
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Function
GND
GND
INTRN
D6
Pin
Function
x2
Pin
1
Function
NC
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Function
Pin
Function
OP2
A3
31
32
33
34
35
36
37
38
39
40
41
42
43
44
OP5
OP7
D1
31
32
33
34
35
36
37
38
39
40
41
42
43
44
2
IP0
RESET
CEN
IP2
2
A0
OP0
3
WRN
RDN
RxDB
TxDB
OP1
OP3
OP5
OP7
I/M
3
IP3
TxDA
NC
4
4
A1
D3
5
D4
IP6
5
IP1
D5
RxDA
X1/CLK
X2
6
D2
IP5
6
A2
D7
7
D0
IP4
7
A3
V
SS
8
NC
V
V
CC
8
IP0
NC
RESET
CEN
IP2
9
OP6
OP4
OP2
OP0
TxDA
RxDA
x1/clk
CC
9
WRN
RDN
RxDB
I/M
INTRN
D6
10
11
12
13
14
15
A0
IP3
A1
IP1
A2
10
11
12
13
14
15
D4
IP6
D1
D2
IP5
D3
TxDB
OP1
OP3
D0
IP4
D5
OP6
OP4
V
CC
D7
SD00672
SD00671
4
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
PIN CONFIGURATION DIAGRAM
68XXX PIN CONFIGURATION
44
34
6
40
1
7
39
1
33
23
PLCC
PQFP
11
29
17
18
28
12
22
Pin
1
Function
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Function
GND
GND
INTRN
D6
Pin
Function
x2
Pin
1
Function
NC
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Function
Pin
Function
OP2
A3
31
32
33
34
35
36
37
38
39
40
41
42
43
44
OP5
OP7
D1
31
32
33
34
35
36
37
38
39
40
41
42
43
44
2
IP0
RESETN
CEN
2
A0
OP0
3
R/WN
DACKN
RxDB
TxDB
OP1
OP3
OP5
OP7
I/M
3
IP3
TxDA
NC
4
IP2
4
A1
D3
5
D4
IACKN
IP5
5
IP1
D5
RxDA
X1/CLK
X2
6
D2
6
A2
D7
7
D0
IP4
7
A3
V
SS
8
NC
V
V
CC
8
IP0
NC
RESETN
CEN
9
OP6
OP4
OP2
OP0
TxDA
RxDA
x1/clk
CC
9
R/WN
DACKN
RxDB
I/M
INTRN
D6
10
11
12
13
14
15
A0
IP3
A1
IP1
A2
10
11
12
13
14
15
IP2
D4
IACKN
IP5
D1
D2
D3
TxDB
OP1
OP3
D0
IP4
D5
OP6
OP4
V
CC
D7
SD00674
SD00673
5
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
8
CHANNEL A
D0–D7
RDN
BUS BUFFER
16 BYTE TRANSMIT
FIFO
TxDA
RxDA
TRANSMIT
SHIFT REGISTER
OPERATION CONTROL
16 BYTE RECEIVE
FIFO
WRN
CEN
ADDRESS
DECODE
WATCH DOG TIMER
4
A0–A3
RESET
RECEIVE SHIFT
REGISTER
R/W CONTROL
MRA0, 1, 2
CRA
SRA
INTERRUPT CONTROL
IMR
TxDB
RxDB
INTRN
CHANNEL B
(AS ABOVE)
ISR
GP
INPUT PORT
CHANGE OF
STATE
DETECTORS (4)
TIMING
7
IP0-IP6
BAUD RATE
GENERATOR
IPCR
ACR
CLOCK
SELECTORS
COUNTER/
TIMER
OUTPUT PORT
FUNCTION
SELECT LOGIC
8
OP0-OP7
X1/CLK
X2
XTAL OSC
OPCR
OPR
CSRA
CSRB
ACR
CTL
CTU
V
CC
V
SS
SD00685
Figure 1. Block Diagram (80XXX mode)
6
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
8
CHANNEL A
D0–D7
BUS BUFFER
16 BYTE TRANSMIT
FIFO
TxDA
RxDA
TRANSMIT
SHIFT REGISTER
OPERATION CONTROL
R/WN
16 BYTE RECEIVE
FIFO
IACKN
CEN
ADDRESS
DECODE
WATCH DOG TIMER
4
A0–A3
RESETN
RECEIVE SHIFT
REGISTER
R/W CONTROL
MRA0, 1, 2
CRA
SRA
INTERRUPT CONTROL
IMR
TxDB
RxDB
INTRN
CHANNEL B
(AS ABOVE)
ISR
IVR
DACKN
INPUT PORT
CHANGE OF
STATE
DETECTORS (4)
TIMING
6
IP0-IP5
BAUD RATE
GENERATOR
IPCR
ACR
CLOCK
SELECTORS
COUNTER/
TIMER
OUTPUT PORT
FUNCTION
SELECT LOGIC
8
OP0-OP7
X1/CLK
X2
XTAL OSC
OPCR
OPR
CSRA
CSRB
ACR
CTL
CTU
V
CC
V
SS
SD00694
Figure 2. Block Diagram (68XXX mode)
7
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
PIN CONFIGURATION FOR 80XXX BUS INTERFACE (INTEL )
PIN
TYPE
SYMBOL
I/M
NAME AND FUNCTION
I
Bus Configuration: When high or not connected configures the bus interface to the Conditions shown in this table.
D0–D7
I/O
Data Bus: Bi-directional 3-State data bus used to transfer commands, data and status between the DUART and the
CPU. D0 is the least significant bit.
CEN
I
Chip Enable: Active-Low input signal. When Low, data transfers between the CPU and the DUART are enabled on
D0–D7 as controlled by the WRN, RDN and A0–A3 inputs. When High, places the D0–D7 lines in the 3-State
condition.
WRN
RDN
I
I
Write Strobe: When Low and CEN is also Low, the contents of the data bus is loaded into the addressed register. The
transfer occurs on the rising edge of the signal.
Read Strobe: When Low and CEN is also Low, causes the contents of the addressed register to be presented on the
data bus. The read cycle begins on the falling edge of RDN.
A0–A3
I
I
Address Inputs: Select the DUART internal registers and ports for read/write operations.
RESET
Reset: A High level clears internal registers (SRA, SRB, IMR, ISR, OPR, OPCR), puts OP0–OP7 in the High state,
stops the counter/timer, and puts Channels A and B in the inactive state, with the TxDA and TxDB outputs in the mark
(High) state. Sets MR pointer to MR1. See Figure 4
INTRN
X1/CLK
X2
O
I
Interrupt Request: Active-Low, open-drain, output which signals the CPU that one or more of the eight maskable
interrupting conditions are true. This pin requires a pullup device.
Crystal 1: Crystal or external clock input. A crystal or clock of the specified limits must be supplied at all times. When a
crystal is used, a capacitor must be connected from this pin to ground (see Figure 11).
O
Crystal 2: Connection for other side of the crystal. When a crystal is used, a capacitor must be connected from this pin
to ground (see Figure 11). If X1/CLK is driven from an external source, this pin must be left open.
RxDA
RxDB
TxDA
I
I
Channel A Receiver Serial Data Input: The least significant bit is received first. “Mark” is High; “space” is Low.
Channel B Receiver Serial Data Input: The least significant bit is received first. “Mark” is High; “space” is Low.
O
Channel A Transmitter Serial Data Output: The least significant bit is transmitted first. This output is held in the “mark”
condition when the transmitter is disabled, idle or when operating in local loop back mode. “Mark” is High; “space” is Low.
TxDB
OP0
OP1
O
O
O
Channel B Transmitter Serial Data Output: The least significant bit is transmitted first. This output is held in the ‘mark’
condition when the transmitter is disabled, idle, or when operating in local loop back mode. ‘Mark’ is High; ‘space’ is Low.
Output 0: General purpose output or Channel A request to send (RTSAN, active-Low). Can be deactivated
automatically on receive or transmit.
Output 1: General-purpose output or Channel B request to send (RTSBN, active-Low). Can be deactivated
automatically on receive or transmit.
OP2
OP3
O
O
Output 2: General purpose output, or Channel A transmitter 1X or 16X clock output, or Channel A receiver 1X clock output.
Output 3: General purpose output or open-drain, active-Low counter/timer output or Channel B transmitter 1X clock
output, or Channel B receiver 1X clock output.
OP4
OP5
OP6
OP7
IP0
O
O
O
O
I
Output 4: General purpose output or Channel A open-drain, active-Low, RxA interrupt ISR[1] output.
Output 5: General-purpose output or Channel B open-drain, active-Low, RxB interrupt ISR[5] output.
Output 6: General purpose output or Channel A open-drain, active-Low, TxA interrupt ISR[0] output.
Output 7: General-purpose output, or Channel B open-drain, active-Low, TxB interrupt ISR[4] output.
Input 0: General purpose input or Channel A clear to send active-Low input (CTSAN).
Input 1: General purpose input or Channel B clear to send active-Low input (CTSBN).
Input 2: General-purpose input or counter/timer external clock input.
IP1
I
IP2
I
IP3
I
Input 3: General purpose input or Channel A transmitter external clock input (TxCA). When the external clock is used
by the transmitter, the transmitted data is clocked on the falling edge of the clock.
IP4
IP5
IP6
I
I
I
Input 4: General purpose input or Channel A receiver external clock input (RxCA). When the external clock is used by
the receiver, the received data is sampled on the rising edge of the clock.
Input 5: General purpose input or Channel B transmitter external clock input (TxCB). When the external clock is used
by the transmitter, the transmitted data is clocked on the falling edge of the clock.
Input 6: General purpose input or Channel B receiver external clock input (RxCB). When the external clock is used by
the receiver, the received data is sampled on the rising edge of the clock.
V
Pwr
Pwr
Power Supply: +3.3 or +5V supply input ±10%
CC
GND
Ground
8
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
PIN CONFIGURATION FOR 68XXX BUS INTERFACE (MOTOROLA )
PIN
TYPE
SYMBOL
I/M
NAME AND FUNCTION
I
Bus Configuration: When low configures the bus interface to the Conditions shown in this table.
D0–D7
I/O
Data Bus: Bi-directional 3-State data bus used to transfer commands, data and status between the DUART and the
CPU. D0 is the least significant bit.
CEN
I
Chip Enable: Active-Low input signal. When Low, data transfers between the CPU and the DUART are enabled on
D0–D7 as controlled by the R/WN and A0–A3 inputs. When High, places the D0–D7 lines in the 3-State condition.
R/WN
I
I
Read/Write: Input Signal. When CEN is low R/WN high input indicates a read cycle; when low indicates a write cycle.
IACKN
Interrupt Acknowledge: Active low input indicating an interrupt acknowledge cycle. Usually asserted by the CPU in
response to an interrupt request. When asserted places the interrupt vector on the bus and asserts DACKN.
DACKN
O
Data Transfer Acknowledge: A3-State active -low output asserted in a write, read, or interrupt acknowledge cycle to
indicate proper transfer of data between the CPU and the DUART.
A0–A3
I
I
Address Inputs: Select the DUART internal registers and ports for read/write operations.
RESETN
Reset: A low level clears internal registers (SRA, SRB, IMR, ISR, OPR, OPCR), puts OP0–OP7 in the High state,
stops the counter/timer, and puts Channels A and B in the inactive state, with the TxDA and TxDB outputs in the mark
(High) state. Sets MR pointer to MR1. See Figure 4
INTRN
X1/CLK
X2
O
I
Interrupt Request: Active-Low, open-drain, output which signals the CPU that one or more of the eight maskable
interrupting conditions are true. This pin requires a pullup.
Crystal 1: Crystal or external clock input. A crystal or clock of the specified limits must be supplied at all times. When
a crystal is used, a capacitor must be connected from this pin to ground (see Figure 11).
O
Crystal 2: Connection for other side of the crystal. When a crystal is used, a capacitor must be connected from this
pin to ground (see Figure 11). If X1/CLK is driven from an external source, this pin must be left open.
RxDA
RxDB
TxDA
I
I
Channel A Receiver Serial Data Input: The least significant bit is received first. “Mark” is High, “space” is Low.
Channel B Receiver Serial Data Input: The least significant bit is received first. “Mark” is High, “space” is Low.
O
Channel A Transmitter Serial Data Output: The least significant bit is transmitted first. This output is held in the “mark”
condition when the transmitter is disabled, idle or when operating in local loop back mode. “Mark” is High; “space” is Low.
TxDB
OP0
OP1
OP2
OP3
O
O
O
O
O
Channel B Transmitter Serial Data Output: The least significant bit is transmitted first. This output is held in the ‘mark’
condition when the transmitter is disabled, idle, or when operating in local loop back mode. ‘Mark’ is High; ‘space’ is Low.
Output 0: General purpose output or Channel A request to send (RTSAN, active-Low). Can be deactivated
automatically on receive or transmit.
Output 1: General-purpose output or Channel B request to send (RTSBN, active-Low). Can be deactivated
automatically on receive or transmit.
Output 2: General purpose output, or Channel A transmitter 1X or 16X clock output, or Channel A receiver 1X clock
output.
Output 3: General purpose output or open-drain, active-Low counter/timer output or Channel B transmitter 1X clock
output, or Channel B receiver 1X clock output.
OP4
OP5
OP6
OP7
IP0
O
O
O
O
I
Output 4: General purpose output or Channel A open-drain, active-Low, RxA interrupt ISR [1] output.
Output 5: General-purpose output or Channel B open-drain, active-Low, RxB interrupt ISR[5] output.
Output 6: General purpose output or Channel A open-drain, active-Low, TxA interrupt ISR[0] output.
Output 7: General-purpose output, or Channel B open-drain, active-Low, TxB interrupt ISR[4] output.
Input 0: General purpose input or Channel A clear to send active-Low input (CTSAN).
Input 1: General purpose input or Channel B clear to send active-Low input (CTSBN).
Input 2: General-purpose input or counter/timer external clock input.
IP1
I
IP2
I
IP3
I
Input 3: General purpose input or Channel A transmitter external clock input (TxCA). When the external clock is used
by the transmitter, the transmitted data is clocked on the falling edge of the clock.
IP4
IP5
I
I
Input 4: General purpose input or Channel A receiver external clock input (RxCA). When the external clock is used by
the receiver, the received data is sampled on the rising edge of the clock.
Input 5: General purpose input or Channel B transmitter external clock input (TxCB). When the external clock is used
by the transmitter, the transmitted data is clocked on the falling edge of the clock.
V
Pwr
Pwr
Power Supply: +3.3 or +5V supply input ±10%
CC
GND
Ground
9
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
1
ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
RATING
Note 4
UNIT
°C
2
T
Operating ambient temperature range
amb
T
Storage temperature range
–65 to +150
–0.5 to +7.0
°C
stg
3
V
Voltage from V to GND
V
CC
CC
3
V
P
P
Voltage from any pin to GND
–0.5 to V +0.5
V
S
CC
Package power dissipation (PLCC44)
Package power dissipation (PQFP44)
Derating factor above 25_C (PLCC44)
Derating factor above 25_C (PQFP44)
2.4
1.78
19
W
D
W
D
mW/°C
mW/°C
14
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other condition above those indicated in the operation section of this specification is not
implied.
2. For operating at elevated temperatures, the device must be derated based on +150°C maximum junction temperature.
3. This product includes circuitry specifically designed for the protection of its internal devices from damaging effects of excessive static
charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying any voltages larger than the rated maxima.
4. Parameters are valid over specified temperature and voltage range.
1, 2, 3
DC ELECTRICAL CHARACTERISTICS
V
= 5V ± 10%, T
= –40°C to +85°C, unless otherwise specified.
CC
amb
LIMITS
Typ
SYMBOL
PARAMETER
TEST CONDITIONS
Min
Max
UNIT
V
V
V
V
Input low voltage
0.8
V
V
V
V
IL
Input high voltage (except X1/CLK)
Input high voltage (X1/CLK)
Output low voltage
2.4
1.5
2.4
0.2
IH
IH
OL
0.8*V
CC
0.4
I
OL
= 2.4mA
4
V
I
Output high voltage (except OD outputs)
V
-0.5
V
I
= -400µA
OH
CC
OH
X1/CLK input current - power down
X1/CLK input low current - operating
X1/CLK input high current - operating
Input leakage current:
0.5
0.05
0.5
0
µA
µA
µA
V
= 0 to V
IX1PD
IN
CC
I
I
V
IN
= 0
–130
0
ILX1
V
= V
130
IHX1
IN
CC
All except input port pins
V
= 0 to V
= 0 to V
–0.5
–8
0.05
0.05
+0.5
+0.5
0.5
µA
µA
µA
µA
µA
µA
I
IN
CC
CC
I
5
Input port pins
V
IN
I
I
I
I
Output off current high, 3-State data bus
Output off current low, 3-State data bus
V
= V
IN CC
OZH
OZL
ODL
ODH
V
IN
= 0V
–0.5
–0.5
Open-drain output low current in off-state
Open-drain output high current in off-state
V
IN
= 0
V
= V
0.5
IN
CC
6
Power supply current
Operating mode
CMOS input levels
CMOS input levels
7
25
5
mA
I
CC
Power down mode
≤1
mA
NOTES:
1. Parameters are valid over specified temperature and voltage range.
2. All voltage measurements are referenced to ground (GND). For testing, all inputs swing between 0.4V and 3.0V with a transition time of
5ns maximum. For X1/CLK, this swing is between 0.4V and 0.8*V . All time measurements are referenced at input voltages of 0.8V and
CC
2.0V and output voltages of 0.8V and 2.0V, as appropriate.
3. Typical values are at +25°C, typical supply voltages, and typical processing parameters.
4. Test conditions for outputs: C = 125pF, except open drain outputs. Test conditions for open drain outputs: C = 125pF,
L
L
constant current source = 2.6mA.
5. Input port pins have active pull-up transistors that will source a typical 2µA from V when the input pins are at V
.
SS
CC
Input port pins at V source 0.0µA.
CC
6. All outputs are disconnected. Inputs are switching between CMOS levels of V -0.2V and V + 0.2V.
CC
SS
10
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
1, 2, 3
DC ELECTRICAL CHARACTERISTICS
V
= 3.3V ± 10%, T
= –40°C to +85°C, unless otherwise specified.
CC
amb
LIMITS
Typ
SYMBOL
PARAMETER
TEST CONDITIONS
Min
Max
0.2*V
UNIT
V
V
V
Input low voltage
Input high voltage
Output low voltage
0.65
1.7
V
V
V
IL
CC
0.8*V
IH
OL
CC
0.2
0.4
I
OL
= 2.4mA
4
V
I
Output high voltage (except OD outputs)
V
–0.5
V –0.2
CC
V
I
= –400µA
OH
CC
OH
X1/CLK input current - power down
X1/CLK input low current - operating
X1/CLK input high current - operating
Input leakage current:
–0.5
–80
0
0.05
+0.5
0
µA
µA
µA
V
= 0 to V
IX1PD
IN
CC
I
I
V
IN
= 0
ILX1
V
= V
80
IHX1
IN
CC
All except input port pins
V
V
= 0 to V
= 0 to V
–0.5
–8
0.05
0.5
+0.5
+0.5
0.5
µA
µA
µA
µA
µA
µA
I
IN
CC
CC
I
5
Input port pins
IN
I
I
I
I
Output off current high, 3-State data bus
Output off current low, 3-State data bus
V
= V
IN CC
OZH
OZL
ODL
ODH
V
IN
= 0V
–0.5
–0.5
Open-drain output low current in off-state
Open-drain output high current in off-state
V
IN
= 0
V
= V
0.5
IN
CC
6
Power supply current
Operating mode
CMOS input levels
CMOS input levels
5
mA
I
CC
Power down mode
≤1
5.0
mA
NOTES:
1. Parameters are valid over specified temperature and voltage range.
2. All voltage measurements are referenced to ground (GND). For testing, all inputs swing between 0.4V and 3.0V with a transition time of
5ns maximum. For X1/CLK, this swing is between 0.4V and 0.8*V . All time measurements are referenced at input voltages of 0.8V and
CC
2.0V and output voltages of 0.8V and 2.0V, as appropriate.
3. Typical values are at +25°C, typical supply voltages, and typical processing parameters.
4. Test conditions for outputs: C = 125pF, except open drain outputs. Test conditions for open drain outputs: C = 125pF,
L
L
constant current source = 2.6mA.
5. Input port pins have active pull-up transistors that will source a typical 2µA from V when the input pins are at V
.
SS
CC
Input port pins at V source 0.0µA.
CC
6. All outputs are disconnected. Inputs are switching between CMOS levels of V –0.2V and V +0.2V.
CC
SS
11
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
1, 2, 3
AC CHARACTERISTICS (5 VOLT)
V
= 5.0V ± 10%, T
= –40°C to +85°C, unless otherwise specified.
CC
amb
4
LIMITS
SYMBOL
Reset Timing (See Figure 4)
Reset pulse width
PARAMETER
UNIT
Min
Typ
Max
t
100
18
ns
RES
5
Bus Timing (See Figure 5)
t
A0–A3 setup time to RDN, WRN Low
10
20
0
6
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
*AS
*AH
*CS
*CH
t
t
A0–A3 hold time from RDN, WRN low
12
CEN setup time to RDN, WRN low
t
CEN Hold time from RDN. WRN low
0
t
WRN, RDN pulse width (Low time)
15
8
*RW
t
Data valid after RDN low (125pF load. See Figure 3 for smaller loads.)
40
55
20
*DD
6
t
RDN low to data bus active
0
*DA
t
Data bus floating after RDN or CEN high
*DF
7
t
RDN or CEN high to data bus invalid
0
25
0
*DI
*DS
*DH
t
Data bus setup time before WRN or CEN high (write cycle)
Data hold time after WRN high
17
–12
10
t
5, 7
t
High time between read and/or write cycles
15
*RWD
5
Port Timing (See Figure 9)
t
Port in setup time before RDN low (Read IP ports cycle)
Port in hold time after RDN high
0
0
–20
–20
40
ns
ns
ns
*PS
*PH
*PD
t
t
OP port valid after WRN or CEN high (OPR write cycle)
60
Interrupt Timing (See Figure 10)
INTRN (or OP3–OP7 when used as interrupts) negated from:
t
*IR
Read RxFIFO (RxRDY/FFULL interrupt)
Write TxFIFO (TxRDY interrupt)
40
40
40
40
40
40
60
60
60
60
60
60
ns
ns
ns
ns
ns
ns
Reset Command (delta break change interrupt)
Stop C/T command (Counter/timer interrupt
Read IPCR (delta input port change interrupt)
Write IMR (Clear of change interrupt mask bit(s))
Clock Timing (See Figure 11)
t
f
X1/CLK high or low time
30
0.1
30
0
20
3.686
10
ns
MHz
ns
*CLK
*CLK
*CTC
*CTC
8
X1/CLK frequency
8
8
f
f
C/T Clk (IP2) high or low time (C/T external clock input)
8
C/T Clk (IP2) frequency
MHz
ns
t
RxC high or low time (16X)
RxC Frequency (16X)
30
0
10
10
*RX
*RX
16
1
MHz
MHz
ns
f
8, 9
RxC Frequency (1x)
0
t
f
TxC High or low time (16X)
TxC frequency (16X)
30
*TX
16
1
MHz
MHz
*TX
8, 9
TxC frequency (1X)
0
Transmitter Timing, external clock (See Figure 12)
t
t
TxD output delay from TxC low (TxC input pin)
40
6
60
30
ns
ns
*TXD
*TCS
Output delay from TxC output pin low to TxD data output
12
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
4
LIMITS
SYMBOL
PARAMETER
Min
Typ
Max
UNIT
Receiver Timing, external clock (See Figure 13)
t
RxD data setup time to RxC high
RxD data hold time from RxC high
50
50
40
40
ns
ns
*RXS
*RXH
t
10
68000 or Motorola bus timing (See Figures 6, 7, 8)
10
t
DACKN Low (read cycle) from X1 High
15
15
8
20
20
10
ns
ns
ns
ns
DCR
t
DACKN Low (write cycle) from X1 High
DCW
t
DACKN High impedance from CEN or IACKN High
CEN or IACKN setup time to X1 High for minimum DACKN cycle
DAT
t
10
8
CSC
NOTES:
1. Parameters are valid over specified temperature and voltage range.
2. All voltage measurements are referenced to ground (GND). For testing, all inputs swing between 0.4 V and 3.0 V with a transition time of
5 ns maximum. For X1/CLK this swing is between 0.4 V and 0.8*V . All time measurements are referenced at input voltages of 0.8 V and
CC
2.0 V and output voltages of 0.8 V and 2.0 V, as appropriate.
3. Test conditions for outputs: CL = 125 pF, except open drain outputs. Test conditions for open drain outputs: C = 125 pF,
L
constant current source = 2.6mA.
4. Typical values are the average values at +25°C and 5V.
5. Timing is illustrated and referenced to the WRN and RDN Inputs. Also, CEN may be the “strobing” input. CEN and RDN (also CEN and
WRN) are ORed internally. The signal asserted last initiates the cycle and the signal negated first terminates the cycle.
6. Guaranteed by characterization of sample units.
7. If CEN is used as the “strobing” input, the parameter defines the minimum High times between one CEN and the next. The RDN signal must
be negated for t
to guarantee that any status register changes are valid.
RWD
8. Minimum frequencies are not tested but are guaranteed by design.
9. Clocks for 1X mode should maintain a 60/40 duty cycle or better.
10.Minimum DACKN time is t
= t
+ t
+ two positive edges of the X1 clock. For faster bus cycles, the 80XXX bus timing may be used
DCR
DSC
DCR
while in the 68XXX mode. It is not necessary to wait for DACKN to insure the proper operation of the SC28C92. In all cases the data will be
written to the SC28L92 on the falling edge of DACKN or the rise of CEN. The fall of CEN initializes the bus cycle. The rise of CEN ends the
bus cycle. DACKN low or CEN high completes the write cycle.
60
V
= 3.3V @ +25°C
CC
55
50
45
40
35
30
25
20
15
10
5
5.0V @ +25°C
T
dd
(ns)
12 pF
30 pF
100 pF
100
125 pF
230 pF
0
0
20
40
60
80
120
pF
140
160
180
200
220
240
SD00684
NOTES:
Bus cycle times:
(80XXX mode): t + t
= 70ns @ 5V, 40ns @ 3.3V + rise and fall time of control signals
RWD
DD
(68XXX mode) = t
+ t
+ 1 cycle of the X1 clock @ 5V + rise and fall time of control signals
CSC
DAT
Figure 3. Port Timing vs. Capacitive Loading at typical conditions
13
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
1, 2, 3
AC CHARACTERISTICS (3.3 VOLT)
V
= 3.3V ± 10%, T
= –40°C to +85°C, unless otherwise specified.
CC
amb
4
LIMITS
SYMBOL
Reset Timing (See Figure 4)
Reset pulse width
PARAMETER
UNIT
Min
Typ
Max
t
100
20
ns
RES
5
Bus Timing (See Figure 5)
t
A0–A3 setup time to RDN, WRN Low
10
25
0
6
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
*AS
*AH
*CS
*CH
t
t
A0–A3 hold time from RDN, WRN low
16
CEN setup time to RDN, WRN low
t
CEN Hold time from RDN. WRN low
0
t
WRN, RDN pulse width (Low time)
20
10
46
*RW
t
Data valid after RDN low (125pF load. See Figure 3 for smaller loads.)
75
20
*DD
6
t
RDN low to data bus active
0
*DA
t
Data bus floating after RDN or CEN high
15
*DF
7
t
RDN or CEN high to data bus invalid
0
25
0
*DI
*DS
*DH
t
Data bus setup time before WRN or CEN high (write cycle)
Data hold time after WRN high
20
–15
10
t
5, 7
t
High time between read and/or write cycles
20
*RWD
5
Port Timing (See Figure 9)
t
Port in setup time before RDN low (Read IP ports cycle)
Port in hold time after RDN high
0
0
–20
–20
50
ns
ns
ns
*PS
*PH
*PD
t
t
OP port valid after WRN or CEN high (OPR write cycle)
70
Interrupt Timing (See Figure 10)
INTRN (or OP3–OP7 when used as interrupts) negated from:
t
*IR
Read RxFIFO (RxRDY/FFULL interrupt)
Write TxFIFO (TxRDY interrupt)
40
40
40
40
40
40
60
60
60
60
60
60
ns
ns
ns
ns
ns
ns
Reset Command (delta break change interrupt)
Stop C/T command (Counter/timer interrupt
Read IPCR (delta input port change interrupt)
Write IMR (Clear of change interrupt mask bit(s))
Clock Timing (See Figure 11)
t
f
X1/CLK high or low time
30
0.1
30
0
25
3.686
15
ns
MHz
ns
*CLK
*CLK
*CTC
*CTC
8
X1/CLK frequency
8
8
f
f
C/T Clk (IP2) high or low time (C/T external clock input)
8
C/T Clk (IP2) frequency
MHz
ns
t
RxC high or low time (16X)
RxC Frequency (16X)
30
0
10
15
*RX
*RX
16
1
MHz
MHz
ns
f
8, 9
RxC Frequency (1x)
0
t
f
TxC High or low time (16X)
TxC frequency (16X)
30
*TX
16
1
MHz
MHz
*TX
8, 9
TxC frequency (1X)
0
Transmitter Timing, external clock (See Figure 12)
t
t
TxD output delay from TxC low (TxC input pin)
40
8
60
30
ns
ns
*TXD
*TCS
Output delay from TxC output pin low to TxD data output
14
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
4
LIMITS
SYMBOL
PARAMETER
Min
Typ
Max
UNIT
Receiver Timing, external clock (See Figure 13)
t
RxD data setup time to RxC high
RxD data hold time from RxC high
50
50
10
10
ns
ns
*RXS
*RXH
t
10
68000 or Motorola bus timing (See Figures 6, 7, 8)
10
t
DACKN Low (read cycle) from X1 High
18
18
10
10
25
25
15
ns
ns
ns
ns
DCR
t
DACKN Low (write cycle) from X1 High
DCW
t
DACKN High impedance from CEN or IACKN High
CEN or IACKN setup time to X1 High for minimum DACKN cycle
DAT
t
15
CSC
NOTES:
1. Parameters are valid over specified temperature and voltage range.
2. All voltage measurements are referenced to ground (GND). For testing, all inputs swing between 0.4 V and 3.0 V with a transition time of
5 ns maximum. For X1/CLK this swing is between 0.4 V and 0.8*V . All time measurements are referenced at input voltages of 0.8 V and
CC
2.0 V and output voltages of 0.8 V and 2.0 V, as appropriate.
3. Test conditions for outputs: CL = 125 pF, except open drain outputs. Test conditions for open drain outputs: C = 125 pF,
L
constant current source = 2.6mA.
4. Typical values are the average values at +25°C and 3.3V.
5. Timing is illustrated and referenced to the WRN and RDN Inputs. Also, CEN may be the “strobing” input. CEN and RDN (also CEN and
WRN) are ORed internally. The signal asserted last initiates the cycle and the signal negated first terminates the cycle.
6. Guaranteed by characterization of sample units.
7. If CEN is used as the “strobing” input, the parameter defines the minimum High times between one CEN and the next. The RDN signal must
be negated for t
to guarantee that any status register changes are valid.
RWD
8. Minimum frequencies are not tested but are guaranteed by design.
9. Clocks for 1X mode should maintain a 60/40 duty cycle or better.
10.Minimum DACKN time is t
= t
+ t
+ two positive edges of the X1 clock. For faster bus cycles, the 80XXX bus timing may be used
DCR
DSC
DCR
while in the 68XXX mode. It is not necessary to wait for DACKN to insure the proper operation of the SC28C92. In all cases the data will be
written to the SC28L92 on the falling edge of DACKN or the rise of CEN. The fall of CEN initializes the bus cycle. The rise of CEN ends the
bus cycle. DACKN low or CEN high completes the write cycle.
15
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
Block Diagram
TIMING CIRCUITS
Crystal Clock
The SC28L92 DUART consists of the following eight major sections:
data bus buffer, operation control, interrupt control, timing,
communications Channels A and B, input port and output port. Refer
to the Block Diagram.
The timing block consists of a crystal oscillator, a baud rate
generator, a programmable 16-bit counter/timer, and four clock
selectors. The crystal oscillator operates directly from a crystal
connected across the X1/CLK and X2 inputs. If an external clock of
the appropriate frequency is available, it may be connected to
X1/CLK. The clock serves as the basic timing reference for the Baud
Rate Generator (BRG), the counter/timer, and other internal circuits.
A clock signal within the limits specified in the specifications section
of this data sheet must always be supplied to the DUART. If an
external clock is used instead of a crystal, X1 should be driven using
a configuration similar to the one in Figure 11. Nominal crystal rate is
3.6864 MHz. Rates up to 8 MHz may be used.
Data Bus Buffer
The data bus buffer provides the interface between the external and
internal data buses. It is controlled by the operation control block to
allow read and write operations to take place between the controlling
CPU and the DUART.
Operation Control
The operation control logic receives operation commands from the
CPU and generates appropriate signals to internal sections to
control device operation. It contains address decoding and read and
write circuits to permit communications with the microprocessor via
the data bus.
BRG
The baud rate generator operates from the oscillator or external
clock input and is capable of generating 28 commonly used data
communications baud rates ranging from 50 to 38.4K baud.
Programming bit 0 of MR0 to a “1” gives additional baud rates of
57.6kB, 115.2kB and 230.4kB (531kHz with X1 at 8.5MHz). These
will be in the 16X mode. A 3.6864 MHz crystal or external clock
must be used to get the standard baud rates. The clock outputs from
the BRG are at 16X the actual baud rate. The counter/timer can be
used as a timer to produce a 16X clock for any other baud rate by
counting down the crystal clock or an external clock. The four clock
selectors allow the independent selection, for each receiver and
transmitter, of any of these baud rates or external timing signal.
Interrupt Control
A single active-Low interrupt output (INTRN) is provided which is
activated upon the occurrence of any of eight internal events.
Associated with the interrupt system are the Interrupt Mask Register
(IMR) and the Interrupt Status Register (ISR). The IMR can be
programmed to select only certain conditions to cause INTRN to be
asserted. The ISR can be read by the CPU to determine all currently
active interrupting conditions. Outputs OP3–OP7 can be
programmed to provide discrete interrupt outputs for the transmitter,
receivers, and counter/timer. When OP3 to OP7 are programmed as
interrupts, their output buffers are changed to the open drain active
low configuration. The OP pins may be used for DMA and modem
control as well. (See output port notes).
Counter/Timer
The counter timer is a 16–bit programmable divider that operates in
one of three modes: counter, timer, time out. In the timer mode it
generates a square wave. In the counter mode it generates a time
delay. In the time out mode it monitors the time between received
characters. The C/T uses the numbers loaded into the
Counter/Timer Lower Register (CTLR) and the Counter/Timer Upper
Register (CTUR) as its divisor.
FIFO Configuration
Each receiver and transmitter has a 16 byte FIFO. These FIFOs
may be configured to operate at a fill capacity of either 8 or 16 bytes.
This feature may be used if it is desired to operate the 28L92 in strict
compliance with the 26C92. The 8 byte/16 byte mode is controlled
by the MR0[3] bit. A 0 value for this bit sets the 8 bit mode ( the
default); a 1 sets the 16 byte mode.
The counter/timer clock source and mode of operation (counter or
timer) is selected by the Auxiliary Control Register bits 6 to 4
(ACR[6:4]). The output of the counter/timer may be used for a baud
rate and/or may be output to the OP pins for some external function
that may be totally unrelated to data transmission. The
counter/timer also sets the counter/timer ready bit in the Interrupt
Status Register (ISR) when its output transitions from 1 to 0. A
register read address (see Table 1) is reserved to issue a start
counter/timer command and a second register read address is
reserved to issue a stop command. The value of D(7:0) is ignored.
The START command always loads the contents of CTUR, CTLR to
the counting registers. The STOP command always resets the ISR
(3) bit in the interrupt status register.
The FIFO fill interrupt level automatically follow the programming of
the MR0[3] bit. See Tables 3 and 4.
68XXX mode
When the I/M pin is connected to V
SC28L92 switches to the bus interface compatible with the Motorola
bus interfaces. Several of the pins change their function as follows:
(ground), the operation of the
CC
Ip6 becomes IACKN input
RDN becomes DACKN
WRN becomes R/WN
The interrupt vector is enabled and the interrupt vector will be placed
on the data bus when IACKN is asserted low. The interrupt vector
register is located at address 0xC. The contents of this register are
set to 0x0F on the application of RESETN.
Timer Mode
In the timer mode a symmetrical square wave is generated whose
half period is equal in time to division of the selected counter/timer
clock frequency by the 16–bit number loaded in the CTLR CTUR.
Thus, the frequency of the counter/timer output will be equal to the
counter/timer clock frequency divided by twice the value of the
CTUR CTLR. While in the timer mode the ISR bit 3 (ISR[3]) will be
set each time the counter/timer transitions from 1 to 0. (High to low)
The generation of DACKN uses two positive edges of the X1 clock
as the DACKN delay from the falling edge of CEN. If the CEN is
withdrawn before two edges of the X1 clock occur, the
generation of DACKN is terminated. Systems not strictly requiring
DACKN may use the 68XXX mode with the bus timing of the 80XXX
mode greatly decreasing the bus cycle time.
16
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
This continues regardless of issuance of the stop counter command.
ISR[3] is reset by the stop counter command.
the counter until the next character is received. The counter timer is
controlled with six commands: Start/Stop C/T, Read/Write
Counter/Timer lower register and Read/Write Counter/Timer upper
register. These commands have slight differences depending on the
mode of operation. Please see the detail of the commands under
the CTLR CTUR Register descriptions.
NOTE: Reading of the CTU and CTL registers in the timer mode is
not meaningful. When the C/T is used to generate a baud rate and
the C/T is selected through the CSR then the receivers and/or
transmitter will be operating in the 16x mode. Calculation for the
number ‘n’ to program the counter timer upper and lower registers is
shown below. N=2 x 16 x Baud rate desired/(C/T Clock Frequency
Often this division will result in a non–integer number; 26.3 for
example. One can only program integer numbers to a digital divider.
Therefore 26 would be chosen. This gives a baud rate error of
0.3/26.3 which is 1.14%; well within the ability of the asynchronous
mode of operation.
Time Out Mode Caution
When operating in the special time out mode, it is possible to
generate what appears to be a “false interrupt”, i.e., an interrupt
without a cause. This may result when a time–out interrupt occurs
and then, BEFORE the interrupt is serviced, another character is
received, i.e., the data stream has started again. (The interrupt
latency is longer than the pause in the data stream.) In this case,
when a new character has been receiver, the counter/timer will be
restarted by the receiver, thereby withdrawing its interrupt. If, at this
time, the interrupt service begins for the previously seen interrupt, a
read of the ISR will show the “Counter Ready” bit not set. If nothing
else is interrupting, this read of the ISR will return a x’00 character.
This action may present the appearance of a spurious interrupt.
Counter Mode
In the counter mode the counter/timer counts the value of the CTLR
CTUR down to zero and then sets the ISR[3] bit and sets the
counter/timer output from 1 to 0. It then rolls over to 65,365 and
continues counting with no further observable effect. Reading the
C/T in the counter mode outputs the present state of the C/T. If the
C/T is not stopped, a read of the C/T may result in changing data on
the data bus.
Communications Channels A and B
Each communications channel of the SC28L92 comprises a
full-duplex asynchronous receiver/transmitter (UART). The operating
frequency for each receiver and transmitter can be selected
independently from the baud rate generator, the counter/timer, or
from an external input. The transmitter accepts parallel data from the
CPU, converts it to a serial bit stream, inserts the appropriate start,
stop, and optional parity bits and outputs a composite serial stream
of data on the TxD output pin. The receiver accepts serial data on
the RxD pin, converts this serial input to parallel format, checks for
start bit, stop bit, parity bit (if any), or break condition and sends an
assembled character to the CPU via the receive FIFO. Three status
bits (Break Received, Framing and Parity Errors) are also FIFOed
with each data character.
Timeout Mode
The timeout mode uses the received data stream to control the
counter. The time–out mode forces the C/T into the timer mode.
Each time a received character is transferred from the shift register
to the RxFIFO, the counter is restarted. If a new character is not
received before the counter reaches zero count, the counter ready
bit is set, and an interrupt can be generated. This mode can be
used to indicate when data has been left in the Rx FIFO for more
than the programmed time limit. If the receiver has been
programmed to interrupt the CPU when the receive FIFO is full, and
the message ends before the FIFO is full, the CPU will not be
interrupted for the remaining characters in the RxFIFO.
Input Port
By programming the C/T such that it would time out in just over one
character time, the above situation could be avoided. The
processor would be interrupted any time the data stream had
stopped for more than one character time. NOTE: This is very
similar to the watch dog time of MR0. The difference is in the
programmability of the delay time and that the watchdog timer is
restarted by either a receiver load to the RxFIFO or a system read
from it.
The inputs to this unlatched 7-bit (6-bit for 68xxx mode) port can be
read by the CPU by performing a read operation at address H’D’. A
High input results in a logic 1 while a Low input results in a logic 0.
D7 will always read as a logic 1. The pins of this port can also serve
as auxiliary inputs to certain portions of the DUART logic, modem
and DMA.
Four change-of-state detectors are provided which are associated
with inputs IP3, IP2, IP1 and IP0. A High-to-Low or Low-to-High
transition of these inputs, lasting longer than 25–50 µs, will set the
corresponding bit in the input port change register. The bits are
cleared when the register is read by the CPU. Any change-of-state
can also be programmed to generate an interrupt to the CPU.
This mode is enabled by writing the appropriate command to the
command register. Writing an ‘Ax’ to CRA or CRB will invoke the
timeout mode for that channel. Writing a ‘Cx’ to CRA or CRB will
disable the timeout mode. Only one receiver should use this mode
at a time. However, if both are on, the timeout occurs after both
receivers have been inactive for the timeout period. The start of the
C/T will be on the logical or of the two receivers.
The input port change of state detection circuitry uses a 38.4 kHz
sampling clock derived from one of the baud rate generator taps. This
results in a sampling period of slightly more than 25 µs (this assumes
that the clock input is 3.6864 MHz). The detection circuitry, in order to
guarantee that a true change in level has occurred, requires two
successive samples at the new logic level be observed. As a
consequence, the minimum duration of the signal change is 25 µs if
the transition occurs “coincident with the first sample pulse”. The
50 µs time refers to the situation in which the change-of-state is “just
missed” and the first change-of-state is not detected until 25 µs later.
The timeout mode disables the regular START/STOP counter
commands and puts the C/T into counter mode under the control of
the received data stream. Each time a received character is
transferred from the shift register to the RxFIFO, the C/T is stopped
after one C/T clock, reloaded with the value in CTUR and CTLR and
then restarted on the next C/T clock. If the C/T is allowed to end the
count before a new character has been received, the counter ready
Bit, ISR[3], will be set. If IMR [3] is set, this will generate an
interrupt. Since receiving a character restarts the C/T, the receipt of
a character after the C/T has timed out will clear the counter ready
bit, ISR [3], and the interrupt. Invoking the ‘Set Timeout Mode On’
command, CRx=‘Ax’, will also clear the counter ready bit and stop
Output Port
The output ports are controlled from six places: the OPCR, OPR,
MR, Command, SOPR and ROPR registers. The OPCR register
17
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
controls the source of the data for the output ports OP2 through
OP7. The data source for output ports OP0 and OP1 is controlled by
the MR and CR registers. When the OPR is the source of the data
for the output ports, the data at the ports is inverted from that in the
OPR register. The content of the OPR register is controlled by the
“Set Output Port Bits Command” and the “Reset Output Bits
Command”. These commands are at E and F, respectively. When
these commands are used, action takes place only at the bit
locations where ones exist. For example, a one in bit location 5 of
the data word used with the “Set Output Port bits” command will
result in OPR5 being set to one. The OP5 would then be set to zero
has returned to the low state. CTS going high during the serialization
of a character will not affect that character.
The transmitter can also control the RTSN outputs, OP0 or OP1 via
MR2[5]. When this mode of operation is set, the meaning of the OP0
or OP1 signals will usually be ‘end of message’. See description of
the MR2[5] bit for more detail. This feature may be used to
automatically “turn around” a transceiver in simplex systems.
Receiver
The SC28L92 is conditioned to receive data when enabled through
the command register. The receiver looks for a High-to-Low
(mark-to-space) transition of the start bit on the RxD input pin. If a
transition is detected, the state of the RxD pin is sampled each 16X
clock for 7-1/2 clocks (16X clock mode) or at the next rising edge of
the bit time clock (1X clock mode). If RxD is sampled High, the start
bit is invalid and the search for a valid start bit begins again. If RxD
is still Low, a valid start bit is assumed and the receiver continues to
sample the input at one bit time intervals at the theoretical center of
the bit, until the proper number of data bits and parity bit (if any)
have been assembled, and one stop bit has been detected. The
least significant bit is received first. The data is then transferred to
the Receive FIFO and the RxRDY bit in the SR is set to a 1. This
condition can be programmed to generate an interrupt at OP4 or
OP5 and INTRN. If the character length is less than 8 bits, the most
significant unused bits in the RxFIFO are set to zero.
(V ). Similarly, a one in bit position 5 of the data word associated
SS
with the “Reset Output Ports Bits” command would set OPR5 to
zero and, hence, the pin OP5 to a one (V ).
DD
These pins along with the IP pins and their change of state detectors
are often used for modem and DMA control.
OPERATION
Transmitter
The SC28L92 is conditioned to transmit data when the transmitter is
enabled through the command register. The SC28L92 indicates to
the CPU that it is ready to accept a character by setting the TxRDY
bit in the status register. This condition can be programmed to
generate an interrupt request at OP6 or OP7 and INTRN. When the
transmitter is initially enabled the TxRDY and TxEMPT bits will be
set in the status register. When a character is loaded to the transmit
FIFO the TxEMPT bit will be reset. The TxEMPT will not set until: 1)
the transmit FIFO is empty and the transmit shift register has
finished transmitting the stop bit of the last character written to the
transmit FIFO, or 2) the transmitter is disabled and then re-enabled.
The TxRDY bit is set whenever the transmitter is enabled and the
TxFIFO is not full. Data is transferred from the holding register to
transmit shift register when it is idle or has completed transmission
of the previous character. Characters cannot be loaded into the
TxFIFO while the transmitter is disabled.
After the stop bit is detected, the receiver will immediately look for
the next start bit. However, if a non-zero character was received
without a stop bit (framing error) and RxD remains Low for one half
of the bit period after the stop bit was sampled, then the receiver
operates as if a new start bit transition had been detected at that
point (one-half bit time after the stop bit was sampled).
The parity error, framing error, and overrun error (if any) are strobed
into the SR from the next byte to be read from the Rx FIFO. If a
break condition is detected (RxD is Low for the entire character
including the stop bit), a character consisting of all zeros will be
loaded into the RxFIFO and the received break bit in the SR is set to
1. The RxD input must return to high for two (2) clock edges of the
X1 crystal clock for the receiver to recognize the end of the break
condition and begin the search for a start bit.
The transmitter converts the parallel data from the CPU to a serial
bit stream on the TxD output pin. It automatically sends a start bit
followed by the programmed number of data bits, an optional parity
bit, and the programmed number of stop bits. The least significant
bit is sent first. Following the transmission of the stop bits, if a new
character is not available in the TxFIFO, the TxD output remains
High and the TxEMT bit in the Status Register (SR) will be set to 1.
Transmission resumes and the TxEMT bit is cleared when the CPU
loads a new character into the TxFIFO.
This will usually require a high time of one X1 clock period or 3
X1 edges since the clock of the controller is not synchronous
to the X1 clock.
Transmitter Reset and Disable
Note the difference between transmitter disable and reset. A
transmitter reset stops transmitter action immediately, clears the
transmitter FIFO and returns the idle state. A transmitter disable
withdraws the transmitter interrupts but allows the transmitter to
continue operation until all bytes in its FIFO and shift register have
been transmitted including the final stop bits. It then returns to its
idle state.
If the transmitter is disabled it continues operating until the character
currently being transmitted and any characters in the TxFIFO,
including parity and stop bits, have been transmitted. New data
cannot be loaded to the TxFIFO when the transmitter is disabled.
When the transmitter is reset it stops sending data immediately.
The transmitter can be forced to send a break (a continuous low
condition) by issuing a START BREAK command via the CR
register. The break is terminated by a STOP BREAK command or a
transmitter reset.
Receiver FIFO
The RxFIFO consists of a First-In-First-Out (FIFO) stack with a
capacity of 8 or 16 characters. Data is loaded from the receive shift
register into the topmost empty position of the FIFO. The RxRDY bit
in the status register is set whenever one or more characters are
available to be read, and a FFULL status bit is set if all 8 or 16 stack
positions are filled with data. Either of these bits can be selected to
cause an interrupt. A read of the RxFIFO outputs the data at the top
of the FIFO. After the read cycle, the data FIFO and its associated
If CTS option is enabled (MR2[4] = 1), the CTS input at IP0 or IP1
must be Low in order for the character to be transmitted. The
transmitter will check the state of the CTS input at the beginning of
each character transmitted. If it is found to be High, the transmitter
will delay the transmission of any following characters until the CTS
18
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
status bits (see below) are ‘popped’ thus emptying a FIFO position
for new data.
Receiver Time-out Mode
In addition to the watch dog timer described in the receiver section,
the counter/timer may be used for a similar function. Its
programmability, of course, allows much greater precision of time
out intervals.
A disabled receiver with data in its FIFO may generate an interrupt
(see “Receiver Status Bits”, below). Its status bits remain active and
its watchdog, if enabled, will continue to operate.
The time-out mode uses the received data stream to control the
counter. Each time a received character is transferred from the shift
register to the RxFIFO, the counter is restarted. If a new character is
not received before the counter reaches zero count, the counter
ready bit is set, and an interrupt can be generated. This mode can
be used to indicate when data has been left in the RxFIFO for more
than the programmed time limit. Otherwise, if the receiver has been
programmed to interrupt the CPU when the receive FIFO is full, and
the message ends before the FIFO is full, the CPU may not know
there is data left in the FIFO. The CTU and CTL value would be
programmed for just over one character time, so that the CPU would
be interrupted as soon as it has stopped receiving continuous data.
This mode can also be used to indicate when the serial line has
been marking for longer than the programmed time limit. In this
case, the CPU has read all of the characters from the FIFO, but the
last character received has started the count. If there is no new data
during the programmed time interval, the counter ready bit will get
set, and an interrupt can be generated.
Receiver Status Bits
In addition to the data word, three status bits (parity error, framing
error, and received break) are also appended to each data character
in the FIFO. The overrun error, MR1(5), is not FIFOed.
Status can be provided in two ways, as programmed by the error
mode control bit in the mode register. In the ‘character’ mode, status
is provided on a character-by-character basis; the status applies
only to the character at the top of the FIFO. In the ‘block’ mode, the
status provided in the SR for these three bits is the logical-OR of the
status for all characters coming to the top of the FIFO since the last
‘reset error’ from the command register was issued. In either mode
reading the SR does not affect the FIFO. The FIFO is ‘popped’ only
when the RxFIFO is read. Therefore the status register should be
read prior to reading the FIFO.
If the FIFO is full when a new character is received, that character is
held in the receive shift register until a FIFO position is available. If
an additional character is received while this state exits, the
The time-out mode is enabled by writing the appropriate command
to the command register. Writing an ‘Ax’ to CRA or CRB will invoke
the time-out mode for that channel. Writing a ‘Cx’ to CRA or CRB
will disable the time-out mode. The time-out mode should only be
used by one channel at once, since it uses the C/T. If, however, the
time-out mode is enabled from both receivers, the time-out will occur
only when both receivers have stopped receiving data for the
time-out period. CTU and CTL must be loaded with a value greater
than the normal receive character period. The time-out mode
disables the regular START/STOP Counter commands and puts the
ca/T into counter mode under the control of the received data
stream. Each time a received character is transferred from the shift
register to the RxFIFO, the C/T is stopped after 1 C/T clock,
reloaded with the value in CTU and CTL and then restarted on the
next C/T clock. If the C/T is allowed to end the count before a new
character has been received, the counter ready bit, ISR[3], will be
set. If IMR[3] is set, this will generate an interrupt. Receiving a
character after the C/T has timed out will clear the counter ready bit,
ISR[3], and the interrupt. Invoking the ‘Set Time-out Mode On’
command, CRx = ‘Ax’, will also clear the counter ready bit and stop
the counter until the next character is received.
contents of the FIFO are not affected; the character previously in the
shift register is lost and the overrun error status bit (SR[4]) will be
set-upon receipt of the start bit of the new (overrunning) character.
The receiver can control the deactivation of RTS. If programmed to
operate in this mode, the RTSN output will be negated when a valid
start bit was received and the FIFO is full. When a FIFO position
becomes available, the RTSN output will be re-asserted (set low)
automatically. This feature can be used to prevent an overrun, in the
receiver, by connecting the RTSN output to the CTSN input of the
transmitting device.
If the receiver is disabled, the FIFO characters can be read.
However, no additional characters can be received until the receiver
is enabled again. If the receiver is reset, the FIFO and all of the
receiver status, and the corresponding output ports and interrupt are
reset. No additional characters can be received until the receiver is
enabled again.
Receiver Reset and Disable
Receiver disable stops the receiver immediately—data being
assembled in the receiver shift register is lost. Data and status in the
FIFO is preserved and may be read. A re-enable of the receiver
after a disable will cause the receiver to begin assembling
characters at the next start bit detected.
Time Out Mode Caution
When operating in the special time out mode, it is possible to
generate what appears to be a “false interrupt”, i.e., an interrupt
without a cause. This may result when a time-out interrupt occurs
and then, BEFORE the interrupt is serviced, another character is
received, i.e., the data stream has started again. (The interrupt
latency is longer than the pause in the data stream.) In this case,
when a new character has been receiver, the counter/timer will be
restarted by the receiver, thereby withdrawing its interrupt. If, at this
time, the interrupt service begins for the previously seen interrupt, a
read of the ISR will show the “Counter Ready” bit not set. If nothing
else is interrupting, this read of the ISR will return a x’00 character.
A receiver reset will discard the present shift register date, reset the
receiver ready bit (RxRDY), clear the status of the byte at the top of
the FIFO and re-align the FIFO read/write pointers.
Watchdog
A ‘watchdog timer’ is associated with each receiver. Its interrupt is
enabled by MR0[7]. The purpose of this timer is to alert the control
processor that characters are in the RxFIFO which have not been
read. This situation may occur at the end of a transmission when the
last few characters received are not sufficient to cause an interrupt.
Multi-drop Mode (9-bit or Wake-Up)
The DUART is equipped with a wake up mode for multi-drop
applications. This mode is selected by programming bits
This counter times out after 64 bit times. It is reset each time a
character is transferred from the receiver shift register to the
RxFIFO or a read of the RxFIFO is executed.
19
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
MR1A[4:3]or MR1B[4:3] to ‘11’ for Channels A and B, respectively.
In this mode of operation, a ‘master’ station transmits an address
character followed by data characters for the addressed ‘slave’
station. The slave stations, with receivers that are normally disabled,
examine the received data stream and ‘wakeup’ the CPU (by setting
RxRDY)only upon receipt of an address character. The CPU
compares the received address to its station address and enables
the receiver if it wishes to receive the subsequent data characters.
Upon receipt of another address character, the CPU may disable the
receiver to initiate the process again.
PROGRAMMING
The operation of the DUART is programmed by writing control words
into the appropriate registers. Operational feedback is provided via
status registers which can be read by the CPU. The addressing of
the registers is described in Table 1.
The contents of certain control registers are initialized to zero on
RESET. Care should be exercised if the contents of a register are
changed during operation, since certain changes may cause
operational problems.
For example, changing the number of bits per character while the
transmitter is active may cause the transmission of an incorrect
character. In general, the contents of the MR, the CSR, and the
OPCR should only be changed while the receiver(s) and
transmitter(s) are not enabled, and certain changes to the ACR
should only be made while the C/T is stopped.
A transmitted character consists of a start bit, the programmed
number of data bits, and Address/Data (A/D) bit, and the
programmed number of stop bits. The polarity of the transmitted A/D
bit is selected by the CPU by programming bit MR1A[2]/MR1B[2].
MR1A[2]/MR1B[2] = 0 transmits a zero in the A/D bit position, which
identifies the corresponding data bits as data while
Each channel has 3 mode registers (MR0, 1, 2) which control the
basic configuration of the channel. Access to these registers is
controlled by independent MR address pointers. These pointers are
set to 0 or 1 by MR control commands in the command register
“Miscellaneous Commands”. Each time the MR registers are
accessed the MR pointer increments, stopping at MR2. It remains
pointing to MR2 until set to 0 or 1 via the miscellaneous commands
of the command register. The pointer is set to 1 on reset for
compatibility with previous Philips Semiconductors UART software.
MR1A[2]/MR1B[2] = 1 transmits a one in the A/D bit position, which
identifies the corresponding data bits as an address. The CPU
should program the mode register prior to loading the corresponding
data bits into the TxFIFO.
In this mode, the receiver continuously looks at the received data
stream, whether it is enabled or disabled. If disabled, it sets the
RxRDY status bit and loads the character into the RxFIFO if the
received A/D bit is a one (address tag), but discards the received
character if the received A/D bit is a zero (data tag). If enabled, all
received characters are transferred to the CPU via the RxFIFO. In
either case, the data bits are loaded into the data FIFO while the
A/D bit is loaded into the status FIFO position normally used for
parity error (SRA[5] or SRB[5]). Framing error, overrun error, and
break detect operate normally whether or not the receive is enabled.
Mode, command, clock select, and status registers are duplicated
for each channel to provide total independent operation and control.
Refer to Table 2 for register bit descriptions. The reserved registers
at addresses H‘02’ and H‘0A’ should never be read during normal
operation since they are reserved for internal diagnostics.
Table 1. SC28L92 register addressing READ (RDN = 0), WRITE (WRN = 0)
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
0
1
Mode Register A (MR0A, MR1A, MR2A)
Status Register A (SRA)
Mode Register A (MR0A, MR1A, MR2A)
Clock Select Register A (CSRA)
Command Register A (CRA)
0
0
Reserved
0
Rx Holding Register A (RxFIFOA)
Input Port Change Register (IPCR)
Interrupt Status Register (ISR)
Counter/Timer Upper (CTU)
Counter/Timer Lower (CTL)
Mode Register B (MR0B, MR1B, MR2B)
Status Register B (SRB)
Tx Holding Register A (TxFIFOA)
Aux. Control Register (ACR)
0
0
Interrupt Mask Register (IMR)
0
C/T Upper Preset Register (CTPU)
C/T Lower Preset Register (CTPL)
Mode Register B (MR0B, MR1B, MR2B)
Clock Select Register B (CSRB)
Command Register B (CRB)
0
1
1
1
Reserved
1
Rx Holding Register B (RxFIFOB)
Interrupt vector (68K mode)
Misc. register (Intel mode), IVR Motorola mode
Input Port (IPR)
Tx Holding Register B (TxFIFOB)
Interrupt vector (68K mode)
1
1
Misc. register (Intel mode), IVR Motorola mode
Output Port Conf. Register (OPCR)
Set Output Port Bits Command (SOPR)
Reset output Port Bits Command (ROPR)
1
1
Start Counter Command
1
Stop Counter Command
NOTE:
1. The three MR registers are accessed via the MR Pointer and Commands 0x1n and 0xBn (where n = represents receiver and transmitter enable bits)
20
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
These are support functions for both Channels
The following named registers are the same for
Channels A and B
Input Port Change Register
Auxiliary Control Register
Interrupt Status Register
Interrupt Mask Register
Counter Timer Upper Value
Counter Timer Lower Value
Counter Timer Preset Upper
Counter Timer Preset Lower
Input Port Register
IPCR
ACR
ISR
R
Mode Register
Status Register
Clock Select
MRnA
SRA
MRnB
SRB
R/W
W
R
R only
W only
W only
R only
W only
IMR
W
R
CSRA
CRA
CSRB
CRB
CTU
CTL
Command Register
Receiver FIFO
Transmitter FIFO
R
RxFIFOA
TxFIFOA
RxFIFOB
TxFIFOB
CTPU
CTPL
IPR
W
W
R
Output Configuration Register
Set Output Port
OPCR
Bits
W
W
W
R/W
Reset Output Port
Bits
Interrupt vector or GP register
IVR/GP
Table 2. Condensed Register bit formats
MR0 – MODE REGISTER 0
Bit 7
BIT 6
BIT 5BIT 4
BIT 3
FIFO SIZE
BIT 2
BIT 1
BIT 0
WATCHDOG
RxINT BIT 2
TxINT (1:0)
BAUD RATE
TEST 2
BAUD RATE
EXTENDED II
EXTENDED 1
MR1 – MODE REGISTER 1
Bit 7
Bit 6
Bit 5
Bit 4:3
Parity Mode
Bit 2
Bit 1:0
Bits per Character
RxRTS Control
RxINT BIT 1
Error Mode
Parity Type
MR2 – MODE REGISTER 2
Bits 7:6
Bit 5
Bit 4
Bit 3:0
Stop Bit Length
Channel Mode
TxRTS Control
CTSN Enable Tx
CSR – CLOCK SELECT REGISTER
Bits 7:4
Bits 3:0
Transmitter Clock select code,
Receiver Clock,Select Code
CR –COMMAND REGISTER
Bits 7:4
Bit 3
Bit 2
Bit 1
Bit 0
Channel Command codes
Disable Tx
Enable Tx
Enable Tx
Enable Rx
SR – CHANNEL STATUS REGISTER
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
TxRDY
Bit 1
Bit 0
Received Break
Framing Error
Parity Error
Overrun Error
TxEMT
RxFULL
RxRDY
IMR – INTERRUPT MASK REGISTER (ENABLES INTERRUPTS)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Change Input
Port
Change Break B
RxRDY B
TxRDTYB
Counter Ready
Change Break A
RxRDY A
TxRDY A
ISR – INTERRUPT STATUS REGISTER
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Change Input
Port
Change Break B
RxRDY B
TxRDTYB
Counter Ready
Change Break A
RxRDY A
TxRDY A
CTPU – COUNTER TIMER PRESET REGISTERS, UPPER
Bits 7:0
8 MSB of the BRG Timer divisor.
21
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
CTPL – COUNTER TIMER PRESET REGISTER, LOWER
Bits 7:0
8 LSB of the BRG Timer divisor.
ACR – AUXILIARY CONTROL REGISTER AND CHANGE OF STATE CONTROL
Bit 7
Bit 6:4
Bit 3
Bit 2
Bit 1
Bit 0
Baud Group
Counter Timer mode and clock select
Enable IP3
Enable IP2
Enable IP1
Enable IP0
IPCR – INPUT PORT CHANGE REGISTER
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Delta IP3
Delta IP2
Delta IP1
Delta IP0
State of IP3
State of IP2
State of IP1
State of IP0
IPR – INPUT PORT REGISTER
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
State of IP
State of IP 6
State of IP 5
State of IP 4
State of IP 3
State of IP 2
State of IP1
State of IP 0
SOPR – SET THE OUTPUT PORT BITS (OPR)
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Set OP 7
Set OP 6
Set OP 5
Set OP 4
Set OP 3
Set OP 2
Set OP 1
Set OP 0
ROPR – RESET OUTPUT PORT BITS (OPR)
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Reset OP 7
Reset OP 6
Reset OP 5
Reset OP 4
Reset OP 3
Reset OP 2
Reset OP 1
Reset OP 0
OPCR OUTPUT PORT CONFIGURATION REGISTER (NOTE OP1 AND OP0 ARE THE RTSN OUTPUT AND
ARE CONTROLLED BY THE MR REGISTER)
Bit 7
BIT 6
BIT 5
BIT 4
BIT(3:2)
Configure OP3
BIT(1:0)
Configure OP7
Configure OP6
Configure OP5
Configure OP4
Configure OP2
REGISTER DESCRIPTIONS Mode Registers
MR0A Mode Register 0. MR0 is accessed by setting the MR pointer to 0 via the command register command B.
Addr
Bit 7
BIT 6
BITS 5:4
BIT 3
BIT 2
BIT 1
BIT 0
MR0A/
MR0B
Rx
RxINT BIT 2
TxINT (1:0)
FIFO SIZE
BAUD RATE
EXTENDED II
TEST 2
BAUD RATE
EXTENDED 1
WATCHDOG
0x00
0x08
0 = Disable
1 = Enable
See Tables in
MR0
See Table 4
0 = 8 byte FIFO
1 = 16 byte FIFO
0 = Normal
1 = Extend II
Set to 0
0 = Normal
1 = Extend
description
MR0[7]—This bit controls the receiver watch dog timer. 0 = disable,
1 = enable. When enabled, the watch dog timer will generate a
receiver interrupt if the receiver FIFO has not been accessed within
64 bit times of the receiver 1X clock. This is used to alert the control
processor that data is in the RxFIFO that has not been read. This
situation may occur when the byte count of the last part of a
message is not large enough to generate an interrupt.
01
10
11
3 or more bytes in FIFO
6 or more bytes in FIFO
8 bytes in FIFO (Rx FULL)
Table 3a. Receiver FIFO interrupt fill
level(MR0(3)=1 (16 bytes)
MR0[6]—Bit 2 of receiver FIFO interrupt level. This bit along with Bit
6 of MR1 sets the fill level of the FIFO that generates the receiver
interrupt.
MR0[6] MR1[6]
Interrupt Condition
00
01
10
11
1 or more bytes in FIFO (Rx RDY)
8 or more bytes in FIFO
MR0[6] MR1[6] Note that this control is split between MR0 and
MR1. This is for backward compatibility to the SC2692 and
SCN2681.
12 or more bytes in FIFO
16 bytes in FIFO (Rx FULL)
Table 3. Receiver FIFO interrupt fill level
(MR0(3) = 0 (8 bytes)
MR0[6] MR1[6]
Interrupt Condition
00
1 or more bytes in FIFO (Rx RDY)
22
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
For the receiver these bits control the number of FIFO positions
filled when the receiver will attempt to interrupt. After the reset the
receiver FIFO is empty. The default setting of these bits cause the
receiver to attempt to interrupt when it has one or more bytes in it.
For the transmitter these bits control the number of FIFO positions
empty when the transmitter will attempt to interrupt. After the reset
the transmit FIFO has 8 bytes empty. It will then attempt to interrupt
as soon as the transmitter is enabled. The default setting of the MR0
bits (5:4) condition the transmitter to attempt to interrupt only when it
is completely empty. As soon as one byte is loaded, it is no longer
empty and hence will withdraw its interrupt request.
MR0[5:4]—Tx interrupt fill level.
Table 4. Transmitter FIFO interrupt fill level
MR0(3) = 0 (8 bytes)
MR0[3]—Selects the FIFO depth at 8 or 16 bytes. See Tables 3 and 4
MR0[5:4]
Interrupt Condition
8 bytes empty (Tx EMPTY)
4 or more bytes empty
MR0[2:0]—These bits are used to select one of the six baud rate
groups.
00
01
10
11
See Table 5 for the group organization.
6 or more bytes empty
000 Normal mode
001 Extended mode I
100 Extended mode II
1 or more bytes empty (Tx RDY)
Table 4a. Transmitter FIFO interrupt fill
level MR0(3) = 1 (16 bytes)
Other combinations of MR2[2:0] should not be used
Note: MR0[3:0] are not used in channel B and should be set to 0.
MR0[5:4]
Interrupt Condition
16 bytes empty (Tx EMPTY)
8 or more bytes empty
00
01
10
11
12 or more bytes empty
1 or more bytes empty (Tx RDY)
MR1A Mode Register 1
Addr
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
MR1A/
MR1B
Rx CONTROLS
RTS
RxINT
BIT 1
ERROR
MODE
PARITY MODE
PARITY TYPE
BITS PER
CHARACTER
0x00
0x08
0 = No
1 = Yes
0 = RxRDY
1 = FFULL
0 = Char
1 = Block
00 = With Parity
01 = Force Parity
10 = No Parity
0 = Even
1 = Odd
00 = 5
01 = 6
10 = 7
11 = 8
11 = Multi-drop Mode
NOTE:
In block error mode, block error conditions must be cleared by using the error reset command (command 4x) or a receiver reset.
MR1A is accessed when the Channel A MR pointer points to MR1.
The pointer is set to MR1 by RESET or by a ‘set pointer’ command
applied via CR command 1. After reading or writing MR1A, the
pointer will point to MR2A.
MR1[6]—Bit 1 of the receiver interrupt control. See description
under MR0[6].
MR1A[5]—Channel A Error Mode Select
This bit select the operating mode of the three FIFOed status bits
(FE, PE, received break) for Channel A. In the ‘character’ mode,
status is provided on a character-by-character basis; the status
applies only to the character at the top of the FIFO. In the ‘block’
mode, the status provided in the SR for these bits is the
accumulation (logical-OR) of the status for all characters coming to
the top of the FIFO since the last ‘reset error’ command for
Channel A was issued.
MR1A[7]—Channel A Receiver Request-to-Send Control
(Flow Control)
This bit controls the deactivation of the RTSAN output (OP0) by the
receiver. This output is normally asserted by setting OPR[0] and
negated by resetting OPR[0]. Proper automatic operation of flow
control requires OPR[0] (channel A) or OPR[1] (channel B) to be set
to logical 1.
MR1A[7] = 1 causes RTSAN to be negated (OP0 is driven to a ‘1’
MR1A[4:3|—Channel A Parity Mode Select
[V ]) upon receipt of a valid start bit if the Channel A FIFO is full.
CC
If ‘with parity’ or ‘force parity’ is selected a parity bit is added to the
transmitted character and the receiver performs a parity check on
incoming data MR1A[4:3] = 11 selects Channel A to operate in the
special multi-drop mode described in the Operation section.
This is the beginning of the reception of the ninth byte. If the FIFO is
not read before the start of the tenth or 17th byte, an overrun
condition will occur and the tenth or 17th or 17th byte will be lost.
However, the bit in OPR[0] is not reset and RTSAN will be asserted
again when an empty FIFO position is available. This feature can be
used for flow control to prevent overrun in the receiver by using the
RTSAN output signal to control the CTSN input of the transmitting
device.
MR1A[2]—Channel A Parity Type Select
This bit selects the parity type (odd or even) if the ‘with parity’ mode
is programmed by MR1A[4:3], and the polarity of the forced parity bit
if the ‘force parity’ mode is programmed. It has no effect if the ‘no
23
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
parity’ mode is programmed. In the special multi-drop mode it
selects the polarity of the A/D bit.
MR1A[1:0]—Channel A Bits Per Character Select
This field selects the number of data bits per character to be
transmitted and received. The character length does not include the
start, parity, and stop bits.
MR2A—Channel A Mode Register 2
MR2A is accessed when the Channel A MR pointer points to MR2, which occurs after any access to MR1A. Accesses to MR2A do not change
the pointer.
MR2 MODE REGISTER 2
Addr
Bit 7
BIT 6
BIT 5
BIT 4
CTS
BIT 3
BIT 2
BIT 1
BIT 0
MR2A/B
CHANNEL MODE
Tx CONTROLS
RTS
STOP BIT LENGTH
ENABLE Tx NOTE: Add 0.5 to binary codes 0–7 for 5 bit character lengths.
0x00
0x08
00 = Normal
0 = 0.563
1 = 0.625
2 = 0.688
3 = 0.750
4 = 0.813
5 = 0.875
6 = 0.938
7 = 1.000
8 = 1.563
9 = 1.625
A = 1.688
B = 1.750
C = 1.813
D = 1.875
E = 1.938
F = 2.000
01 = Auto-Echo
10 = Local loop
11 = Remote loop
0 = No
0 = No
1 = Yes
1 = Yes
NOTE:
Add 0.5 to values shown for 0–7 if channel is programmed for 5 bits/char.
MR2A[7:6]—Channel A Mode Select
MR2A[7:6] = 11 selects remote loop back diagnostic mode. In this
Each channel of the DUART can operate in one of four modes.
MR2A[7:6] = 00 is the normal mode, with the transmitter and
receiver operating independently.
mode:
1. Received data is reclocked and retransmitted on the TxDA
out-put.
MR2A[7:6] = 01 places the channel in the automatic echo mode,
which automatically retransmits the received data. The following
conditions are true while in automatic echo mode:
1. Received data is reclocked and retransmitted on the TxDA
output.
2. The receive clock is used for the transmitter.
3. Received data is not sent to the local CPU, and the error status
conditions are inactive.
4. The received parity is not checked and is not regenerated for
transmission, i.e., transmitted parity is as received.
2. The receive clock is used for the transmitter.
5. The receiver must be enabled.
3. The receiver must be enabled, but the transmitter need not be
enabled.
6. Character framing is not checked, and the stop bits are
retransmitted as received.
4. The Channel A TxRDY and TxEMT status bits are inactive.
7. A received break is echoed as received until the next valid start
bit is detected.
5. The received parity is checked, but is not regenerated for
transmission, i.e. transmitted parity bit is as received.
6. Character framing is checked, but the stop bits are retransmitted
as received.
The user must exercise care when switching into and out of the
various modes. The selected mode will be activated immediately
upon mode selection, even if this occurs in the middle of a received
or transmitted character. Likewise, if a mode is deselected the
device will switch out of the mode immediately. An exception to this
is switching out of auto echo or remote loop back modes: if the
de-selection occurs just after the receiver has sampled the stop bit
(indicated in auto echo by assertion of RxRDY), and the transmitter
is enabled, the transmitter will remain in auto echo mode until the
entire stop has been re-transmitted.
7. A received break is echoed as received until the next valid start
bit is detected.
8. CPU to receiver communication continues normally, but the CPU
to transmitter link is disabled.
MR2A[7:6] = 10 selects local loop back diagnostic mode. In this
mode:
1. The transmitter output is internally connected to the receiver
input.
MR2A[5]—Channel A Transmitter Request-to-Send Control
This bit controls the deactivation of the RTSAN output (OP0) by the
transmitter. This output is normally asserted by setting OPR[0] and
negated by resetting OPR[0]. MR2A[5] = 1 caused OPR[0] to be
reset automatically one bit time after the characters in the Channel A
transmit shift register and in the TxFIFO, if any, are completely
transmitted including the programmed number of stop bits, if the
transmitter is not enabled.
2. The transmit clock is used for the receiver.
3. The TxDA output is held High.
4. The RxDA input is ignored.
5. The transmitter must be enabled, but the receiver need not be
enabled.
6. CPU to transmitter and receiver communications continue
normally.
24
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
This feature can be used to automatically terminate the transmission
of a message as follows (“line turnaround”):
1. Program auto-reset mode: MR2A[5] = 1.
MR0B—Channel B Mode Register 0
MR0B is accessed when the Channel B MR pointer points to MR1.
The pointer is set to MR0 by RESET or by a ‘set pointer’ command
applied via CRB. After reading or writing MR0B, the pointer will point
to MR1B.
2. Enable transmitter.
3. Asset RTSAN: OPR[0] = 1.
4. Send message.
The bit definitions for this register are identical to MR0A, except that
all control actions apply to the Channel B receiver and transmitter
and the corresponding inputs and outputs. MR0B[3:0] are reserved.
5. Disable transmitter after the last character is loaded into the
Channel A TxFIFO.
MR1B—Channel B Mode Register 1
MR1B is accessed when the Channel B MR pointer points to MR1.
The pointer is set to MR1 by RESET or by a ‘set pointer’ command
applied via CRB. After reading or writing MR1B, the pointer will point
to MR2B.
6. The last character will be transmitted and OPR[0] will be reset one
bit time after the last stop bit, causing RTSAN to be negated.
MR2A[4]—Channel A Clear-to-Send Control
If this bit is 0, CTSAN has no effect on the transmitter. If this bit is a
1, the transmitter checks the state of CTSAN (IPO) each time it is
ready to send a character. If IPO is asserted (Low), the character is
transmitted. If it is negated (High), the TxDA output remains in the
marking state and the transmission is delayed until CTSAN goes
low. Changes in CTSAN while a character is being transmitted do
not affect the transmission of that character..
The bit definitions for this register are identical to MR1A, except that
all control actions apply to the Channel B receiver and transmitter
and the corresponding inputs and outputs.
MR2B—Channel B Mode Register 2
MR2B is accessed when the Channel B MR pointer points to MR2,
which occurs after any access to MR1B. Accesses to MR2B do not
change the pointer.
MR2A[3:0]—Channel A Stop Bit Length Select
This field programs the length of the stop bit appended to the
transmitted character. Stop bit lengths of 9/16 to 1 and 1-9/16 to 2
bits, in increments of 1/16 bit, can be programmed for character
lengths of 6, 7, and 8 bits. For a character lengths of 5 bits, 1-1/16 to
2 stop bits can be programmed in increments of 1/16 bit. In all
cases, the receiver only checks for a ‘mark’ condition at the center
of the stop bit position (one half-bit time after the last data bit, or
after the parity bit if enabled is sampled).
The bit definitions for mode register are identical to the bit definitions
for MR2A, except that all control actions apply to the Channel B
receiver and transmitter and the corresponding inputs and outputs.
If an external 1X clock is used for the transmitter, then MR2A[3] = 0
selects one stop bit and MR2A[3] = 1 selects two stop bits to be
transmitted.
25
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
CSR CLOCK SELECT REGISTER
Addr
CSR (7:4)
CSR (3:0)
CSRA/B
RECEIVER CLOCK SELECT
See Text and table 5
TRANSMITTER CLOCK SELECT
0x01
0x09
See Text and table 5
Table 5. Baud rate (base on a 3.6864MHz crystal clock)
MR0[0] = 0 (Normal Mode)
MR0[0] = 1 (Extended Mode I)
MR0[2] = 1 (Extended Mode II)
CSRA[7:4]
0000
0001
0010
0011
0100
0101
0110
0111
ACR[7] = 0
50
ACR[7] = 1
75
ACR[7] = 0
300
ACR[7] = 1
450
ACR[7] = 0
4,800
ACR[7] = 1
7,200
110
110
110
110
880
880
134.5
200
134.5
150
134.5
1200
134.5
900
1,076
1,076
19.2K
28.8K
57.6K
115.2K
1,050
14.4K
28.8K
57.6K
115.2K
2,000
300
300
1800
1800
600
600
3600
3600
1,200
1,050
2,400
4,800
7,200
9,600
38.4K
Timer
IP4–16X
IP4–1X
1,200
2,000
2,400
4,800
1,800
9,600
19.2K
Timer
IP4–16X
IP4–1X
7200
7,200
2,000
14.4K
28.8K
1,800
57.6K
115.2K
Timer
IP4–16X
IP4–1X
1,050
14.4K
28.8K
7,200
57.6K
230.4K
Timer
IP4–16X
IP4–1X
1000
1001
1010
1011
1100
1101
1110
57.6K
4,800
57.6K
4,800
57.6K
9,600
14.4K
9,600
38.4K
Timer
19.2K
Timer
IP4–16X
IP4–1X
IP4–16X
IP4–1X
1111
NOTE:
The receiver clock is always a 16X clock except for CSRA[7:4] = 1111.
CSRA[3:0]—Channel A Transmitter Clock Select
This field selects the baud rate clock for the Channel A transmitter.
The field definition is as shown in Table 5, except as follows:
CSRB—Channel B Clock Select Register
CSRB[7:4]—Channel B Receiver Clock Select
This field selects the baud rate clock for the Channel B receiver. The
field definition is as shown in Table 5, except as follows:
CSRA[3:0]
1110
1111
CSRB[7:4]
IP3–16X
IP3–1X
1110
1111
The transmitter clock is always a 16X clock except for
CSR[3:0] = 1111.
IP6–1X
IP6–16X
The receiver clock is always a 16X clock except for
CSRB[7:4] = 1111.
CSRB[3:0]—Channel B Transmitter Clock Select
This field selects the baud rate clock for the Channel B transmitter.
The field definition is as shown in Table 5, except as follows:
CSRB[3:0]
1110
1111
IP5–1X
IP5–16X
The transmitter clock is always a 16X clock except for
CSRB[3:0] = 1111.
26
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
Table 6. Bit rate generator characteristics
Crystal or Clock = 3.6864MHz
NORMAL RATE (BAUD)
ACTUAL 16X CLOCK (KHz)
ERROR (%)
50
75
0.8
1.2
0
0
110
1.759
2.153
2.4
–0.069
134.5
150
0.059
0
200
3.2
0
300
4.8
0
600
9.6
0
1050
1200
1800
2000
2400
4800
7200
9600
19.2K
38.4K
16.756
19.2
28.8
32.056
38.4
76.8
115.2
153.6
307.2
614.4
–0.260
0
0
0.175
0
0
0
0
0
0
NOTE:
Duty cycle of 16X clock is 50% "1%
27
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
CRA—Channel A Command Register
CRA is a register used to supply commands to Channel A. Multiple commands can be specified in a single write to CRA as long as the
commands are non-conflicting, e.g., the ‘enable transmitter’ and ‘reset transmitter’ commands cannot be specified in a single command word.
CR COMMAND REGISTER
Addr
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
CRA/B
MISCELLANEOUS COMMANDS
Disable Tx
Enable Tx
Disable Rx
Enable Rx
0x02
0x0A
See Text of Channel Command Register
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
NOTES:
Access to the miscellaneous commands should be separated by 3 X1 clock edges. A disabled transmitter cannot be loaded.
CRA[7:4]—Miscellaneous Commands
1010
Set Timeout Mode On. The receiver in this channel will
restart the C/T as each receive character is transferred
from the shift register to the RxFIFO. The C/T is placed
in the counter mode, the START/STOP counter
commands are disabled, the counter is stopped, and
the Counter Ready Bit, ISR[3], is reset. (See also
Watchdog timer description in the receiver section.)
Execution of the commands in the upper four bits of this register
must be separated by 3 X1 clock edges. Other reads or writes
(including writes tot he lower four bits) may be inserted to achieve
this separation.
CRA[7:4]—Commands
1011
1100
Set MR pointer to ‘0’
0000
0001
No command.
Disable Timeout Mode. This command returns control
of the C/T to the regular START/STOP counter
commands. It does not stop the counter, or clear any
pending interrupts. After disabling the timeout mode, a
‘Stop Counter’ command should be issued to force a
reset of the ISR(3) bit
Reset MR pointer. Causes the Channel A MR pointer to
point to MR1.
0010
Reset receiver. Resets the Channel A receiver as if a
hardware reset had been applied. The receiver is
disabled and the FIFO is flushed.
1101
1110
Not used.
0011
0100
Reset transmitter. Resets the Channel A transmitter as
if a hardware reset had been applied.
Power Down Mode On. In this mode, the DUART
oscillator is stopped and all functions requiring this
clock are suspended. The execution of commands
other than disable power down mode (1111) requires a
X1/CLK. While in the power down mode, do not issue
any commands to the CR except the disable power
down mode command. The contents of all registers will
be saved while in this mode. . It is recommended that
the transmitter and receiver be disabled prior to placing
the DUART into power down mode. This command is in
CRA only.
Reset error status. Clears the Channel A Received
Break, Parity Error, and Overrun Error bits in the status
register (SRA[7:4]). Used in character mode to clear OE
status (although RB, PE and FE bits will also be
cleared) and in block mode to clear all error status after
a block of data has been received.
0101
0110
Reset Channel A break change interrupt. Causes the
Channel A break detect change bit in the interrupt
status register (ISR[2]) to be cleared to zero
Start break. Forces the TxDA output Low (spacing). If
the transmitter is empty the start of the break condition
will be delayed up to two bit times. If the transmitter is
active the break begins when transmission of the
character is completed. If a character is in the TxFIFO,
the start of the break will be delayed until that character,
or any other loaded subsequently are transmitted. The
transmitter must be enabled for this command to be
accepted.
1111
Disable Power Down Mode. This command restarts the
oscillator. After invoking this command, wait for the
oscillator to start up before writing further commands to
the CR. This command is in CRA only. For maximum
power reduction input pins should be at V or V
.
SS
DD
CRA[3]—Disable Channel A Transmitter
This command terminates transmitter operation and reset the
TxDRY and TxEMT status bits. However, if a character is being
transmitted or if a character is in the TxFIFO when the transmitter is
disabled, the transmission of the character(s) is completed before
assuming the inactive state.
0111
Stop break. The TxDA line will go High (marking) within
two bit times. TxDA will remain High for one bit time
before the next character, if any, is transmitted.
1000
1001
Assert RTSN. Causes the RTSN output to be asserted
(Low).
CRA[2]—Enable Channel A Transmitter
Enables operation of the Channel A transmitter. The TxRDY and
TxEMT status bits will be asserted if the transmitter is idle.
Negate RTSN. Causes the RTSN output to be negated
(High)
28
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
CRA[1]—Disable Channel A Receiver
CRB—Channel B Command Register
This command terminates operation of the receiver immediately—a
character being received will be lost. The command has no effect on
the receiver status bits or any other control registers. If the special
multi-drop mode is programmed, the receiver operates even if it is
disabled. See Operation section.
CRB is a register used to supply commands to Channel B. Multiple
commands can be specified in a single write to CRB as long as the
commands are non-conflicting, e.g., the ‘enable transmitter’ and
‘reset transmitter’ commands cannot be specified in a single
command word.
CRA[0]—Enable Channel A Receiver
The bit definitions for this register are identical to the bit definitions
for CRA, with the exception of commands “Ex” and “Fx” which are
used for power down mode. These two commands are not used in
CRB. All other control actions that apply to CRA also apply to CRB.
Enables operation of the Channel A receiver. If not in the special
wakeup mode, this also forces the receiver into the search for
start-bit state.
SR STATUS REGISTER Channel A Status Register
Addr
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SRA/B
RECEIVED
BREAK*
FRAMING
ERROR*
PARITY
ERROR*
OVERRUN
ERROR
TxEMT
TxRDY
FFULL
RxRDY
0x01
0x09
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
*These status bits are appended to the corresponding data character in the receive FIFO. A read of the status provides these bits (7:5) from the
top of the FIFO together with bits (4:0). These bits are cleared by a “reset error status” command. In character mode they are discarded when
the corresponding data character is read from the FIFO. In block error mode, the error-reset command (command 4x or receiver reset )must
used to clear block error conditions
SRA[7]—Channel A Received Break This bit indicates that an all
zero character of the programmed length has been received without
a stop bit. Only a single FIFO position is occupied when a break is
received: further entries to the FIFO are inhibited until the RxDA line
returns to the marking state for at least one-half a bit time two
successive edges of the internal or external 1X clock. This will
usually require a high time of one X1 clock period or 3 X1
edges since the clock of the controller is not synchronous to
the X1 clock.
occurs, the character in the receive shift register (and its break
detect, parity error and framing error status, if any) is lost.
This bit is cleared by a ‘reset error status’ command.
SRA[3]—Channel A Transmitter Empty (TxEMTA)
This bit will be set when the transmitter under runs, i.e., both the
TxEMT and TxRDY bits are set. This bit and TxRDY are set when
the transmitter is first enabled and at any time it is re-enabled after
either (a) reset, or (b) the transmitter has assumed the disabled
state. It is always set after transmission of the last stop bit of a
character if no character is in the THR awaiting transmission.
When this bit is set, the Channel A ‘change in break’ bit in the ISR
(ISR[2]) is set. ISR[2] is also set when the end of the break
condition, as defined above, is detected.
It is reset when the THR is loaded by the CPU, a pending
transmitter disable is executed, the transmitter is reset, or the
transmitter is disabled while in the under run condition.
The break detect circuitry can detect breaks that originate in the
middle of a received character. However, if a break begins in the
middle of a character, it must persist until at least the end of the next
character time in order for it to be detected.
SRA[2]—Channel A Transmitter Ready (TxRDYA)
This bit, when set, indicates that the transmit FIFO is not full and
ready to be loaded with another character. This bit is cleared when
the transmit FIFO is loaded by the CPU and there are (after this
load) no more empty locations in the FIFO. It is set when a
character is transferred to the transmit shift register. TxRDYA is
reset when the transmitter is disabled and is set when the
transmitter is first enabled. Characters loaded to the TxFIFO while
this bit is 0 will be lost. This bit has different meaning from ISR[0].
This bit is reset by command 4 (0100) written to the command
register or by receiver reset.
SRA[6]—Channel A Framing Error
This bit, when set, indicates that a stop bit was not detected (not a
logical 1) when the corresponding data character in the FIFO was
received. The stop bit check is made in the middle of the first stop bit
position.
SRA[1]—Channel A FIFO Full (FFULLA)
SRA[5]—Channel A Parity Error
This bit is set when a character is transferred from the receive shift
register to the receive FIFO and the transfer causes the FIFO to
become full, i.e., all eight (or 16) FIFO positions are occupied. It is
reset when the CPU reads the receive FIFO. If a character is waiting
in the receive shift register because the FIFO is full, FFULLA will not
be reset when the CPU reads the receive FIFO. This bit has
different meaning from ISR1 when MR1 6 is programmed to a ‘1’.
This bit is set when the ‘with parity’ or ‘force parity’ mode is
programmed and the corresponding character in the FIFO was
received with incorrect parity.
In the special multi-drop mode the parity error bit stores the receive
A/D (Address/Data) bit.
SRA[4]—Channel A Overrun Error
SRA[0]—Channel A Receiver Ready (RxRDYA)
This bit, when set, indicates that one or more characters in the
received data stream have been lost. It is set upon receipt of a new
character when the FIFO is full and a character is already in the
receive shift register waiting for an empty FIFO position. When this
This bit indicates that a character has been received and is waiting
in the FIFO to be read by the CPU. It is set when the character is
transferred from the receive shift register to the FIFO and reset
29
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
when the CPU reads the receive FIFO, only if (after this read) there
are no more characters in the FIFO – the Rx FIFO becomes empty.
SRB—Channel B Status Register
The bit definitions for this register are identical to the bit definitions
for SRA, except that all status applies to the Channel B receiver and
transmitter and the corresponding inputs and outputs.
OPCR—Output Port Configuration Register
OPCR OUTPUT PORT CONFIGURATION REGISTER
Addr
OPCR
0x0D
Bit 7
OP7
BIT 6
OP6
BIT 5
OP5
BIT 4
OP4
BIT 3
OP3
BIT 2
OP2
BIT 1
OP1
BIT 0
OP0
0 = OPR[7]
0 = OPR[6]
0 = OPR[5]
0 = OPR[4]
00
=
OPR[3]
00
= OPR[2]
1 = TxRDY B
1 = TxRDY A
1 = RxRDY/FFULL B
1 = RxRDY/FFULL A
01 = C/T OUTPUT
01 = TxCA(16X)
10
11
=
=
TxCB(1X)
RxCB(1X)
10
11
=
=
TxCA(1X)
RxCA(1X)
OPCR[7]—OP7 Output Select
This bit programs the OP7 output to provide one of the following:
OPCR[3:2]—OP3 Output Select
This bit programs the OP3 output to provide one of the following:
0
1
The complement of OPR[7].
00 The complement of OPR[3].
The Channel B transmitter interrupt output which is the
complement of ISR[4]. When in this mode OP7 acts as an
open-drain output. Note that this output is not masked by the
contents of the IMR.
01 The counter/timer output, in which case OP3 acts as an
open-drain output. In the timer mode, this output is a square
wave at the programmed frequency. In the counter mode,
the output remains High until terminal count is reached, at
which time it goes Low. The output returns to the High state
when the counter is stopped by a stop counter command.
Note that this output is not masked by the contents of the
IMR.
OPCR[6]—OP6 Output Select
This bit programs the OP6 output to provide one of the following:
10 The 1X clock for the Channel B transmitter, which is the
clock that shifts the transmitted data. If data is not being
transmitted, a free running 1X clock is output.
0
1
The complement of OPR[6].
The Channel A transmitter interrupt output which is the
complement of ISR[0]. When in this mode OP6 acts as an
open-drain output. Note that this output is not masked by the
contents of the IMR.
11 The 1X clock for the Channel B receiver, which is the clock
that samples the received data. If data is not being received,
a free running 1X clock is output.
OPCR[5]—OP5 Output Select
This bit programs the OP5 output to provide one of the following:
OPCR[1:0]—OP2 Output Select
This field programs the OP2 output to provide one of the following:
0
1
The complement of OPR[5].
00 The complement of OPR[2].
The Channel B receiver interrupt output which is the
complement of ISR[5]. When in this mode OP5 acts as an
open-drain output. Note that this output is not masked by the
contents of the IMR.
01 The 16X clock for the Channel A transmitter. This is the
clock selected by CSRA[3:0], and will be a 1X clock if
CSRA[3:0] = 1111.
10 The 1X clock for the Channel A transmitter, which is the
clock that shifts the transmitted data. If data is not being
transmitted, a free running 1X clock is output.
OPCR[4]—OP4 Output Select
This field programs the OP4 output to provide one of the following:
11 The 1X clock for the Channel A receiver, which is the clock
that samples the received data. If data is not being received,
a free running 1X clock is output.
0
1
The complement of OPR[4].
The Channel A receiver interrupt output which is the
complement of ISR[1]. When in this mode OP4 acts as an
open-drain output. Note that this output is not masked by the
contents of the IMR.
30
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
SOPR—Set the Output Port Bits (OPR)
SOPR[7:0]—Ones in the byte written to this register will cause the corresponding bit positions in the OPR to set to 1. Zeros have no effect. This
allows software to set individual bits with our keeping a copy of the OPR bit configuration.
Addr
SOPR
0x0E
Bit 7
OP 7
BIT 6
OP 6
BIT 5
OP 5
BIT 4
OP 4
BIT 3
OP 3
BIT 2
OP 2
BIT 1
OP 1
BIT 0
OP 0
1=set bit
1=set bit
1=set bit
1=set bit
1=set bit
1=set bit
1=set bit
1=set bit
0 = no
0 = no
0 = no
0 = no
0 = no
0 = no
0 = no
0 = no
change
change
change
change
change
change
change
change
ROPR—Reset Output Port Bits (OPR)
ROPR[7:0]—Ones in the byte written to the ROPR will cause the corresponding bit positions in the OPR to set to 0. Zeros have no effect. This
allows software to reset individual bits with our keeping a copy of the OPR bit configuration.
Addr
ROPR
0x0F
Bit 7
OP 7
BIT 6
OP 6
BIT 5
OP 5
BIT 4
OP 4
BIT 3
OP 3
BIT 2
OP 2
BIT 1
OP 1
BIT 0
OP 0
1=reset bit
1=reset bit
1=reset bit
1=reset bit
1=reset bit
1=reset bit
1=reset bit
1=reset bit
0 = no
0 = no
0 = no
0 = no
0 = no
0 = no
0 = no
0 = no
change
change
change
change
change
change
change
change
OPR Output Port Register
The output pins (OP pins) drive the compliment of the data in this register as controlled by SOPR and ROPR.
Addr
N/A
Bit 7
OP 7
BIT 6
OP 6
BIT 5
OP 5
BIT 4
OP 4
BIT 3
OP 3
BIT 2
OP 2
BIT 1
OP 1
BIT 0
OP 0
N/A
0 = Pin High 0 = Pin High
1 = Pin Low 1 = Pin Low
0 = Pin High
1 = Pin Low
0 = Pin High
1 = Pin Low
0 = Pin High
1 = Pin Low
0 = Pin High
1 = Pin Low
0 = Pin High
1 = Pin Low
0 = Pin High
1 = Pin Low
31
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
ACR Auxiliary Control Register
Addr
ACR
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
BRG SET
Select
Counter Timer Mode
Delta IP3 int Delta IP3 int Delta IP3 int Delta IP3 int
Mode and clock sour select
enable
enable
enable
enable
0x04
0 = set 1
1 = set 2
See table 7
0 = off
0 = off
0 = off
0 = off
1 = enabled
1 = enabled
1 = enabled
1 = enabled
ACR—Auxiliary Control Register
Table 7. ACR 6:4 field definition
ACR
6:4
MODE
CLOCK SOURCE
ACR[7]—Baud Rate Generator Set Select
This bit selects one of two sets of baud rates to be generated by the
BRG (see Table 5).
000
001
010
011
Counter External (IP2)
The selected set of rates is available for use by the Channel A and
B receivers and transmitters as described in CSRA and CSRB.
Baud rate generator characteristics are given in Table 6.
Counter TxCA - 1X clock of Channel A transmitter
Counter TxCB - 1X clock of Channel B transmitter
Counter Crystal or external clock (X1/CLK) divided
by 16
ACR[6:4]—Counter/Timer Mode And Clock Source Select
This field selects the operating mode of the counter/timer and its
clock source as shown in Table 7
100
101
110
111
Timer
Timer
Timer
Timer
External (IP2)
External (IP2) divided by 16
Crystal or external clock (X1/CLK)
ACR [3:0]—IP3, IP2, IP1, IP0 Change-of-State Interrupt Enable
This field selects which bits of the input port change register (IPCR)
cause the input change bit in the interrupt status register (ISR [7]) to
be set. If a bit is in the ‘on’ state the setting of the corresponding bit
in the IPCR will also result in the setting of ISR [7], which results in
the generation of an interrupt output if IMR [7] = 1. If a bit is in the
‘off’ state, the setting of that bit in the IPCR has no effect on ISR [7].
NOTE:
Crystal or external clock (X1/CLK) divided
by 16
The timer mode generates a square wave
IPCR INPUT PORT CHANGE REGISTER
Addr
IPCR
0x04
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
IP 2
BIT 1
IP 1
BIT 0
IP 0
Delta IP3
Delta IP3
Delta IP3
Delta IP3
IP 3
0 = no
0 = no
0 = no
0 = no
0 = low
0 = low
0 = low
0 = low
change
change
change
change
1 = change
1 = change
1 = change
1 = change
1 = High
1 = High
1 = High
1 = High
IPCR [7:4]—IP3, IP2, IP1, IP0 Change-of-State
IPCR [3:0]—IP3, IP2, IP1, IP0 Change-of-State
These bits are set when a change-of-state, as defined in the input
port section of this data sheet, occurs at the respective input pins.
They are cleared when the IPCR is read by the CPU. A read of the
IPCR also clears ISR [7], the input change bit in the interrupt status
register. The setting of these bits can be programmed to generate
an interrupt to the CPU.
These bits provide the current state of the respective inputs. The
information is unlatched and reflects the state of the input pins at the
time the IPCR is read.
32
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
ISR—Interrupt Status Register
This register provides the status of all potential interrupt sources. The contents of this register are masked by the Interrupt Mask Register (IMR).
If a bit in the ISR is a ‘1’ and the corresponding bit in the IMR is also a ‘1’, the INTRN output will be asserted (Low). If the corresponding bit in
the IMR is a zero, the state of the bit in the ISR has no effect on the INTRN output. Note that the IMR does not mask the reading of the ISR - the
true status will be provided regardless of the contents of the IMR. The contents of this register are initialized to H‘00’ when the DUART is reset.
ISR INTERRUPT STATUS REGISTER
Addr
ISR
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
INPUT
PORT
DELTA
Break B
RxRDY/
FFULL B
TxRDY B
Counter
Ready
Delta
Break A
RxRDY/
FFULL A
TxRDY A
CHANGE
0x05
0 = not active 0 = not active 0 = not active 0 = not active 0 = not active 0 = not active 0 = not active 0 = not active
1 = active 1 = active 1 = active 1 = active 1 = active 1 = active 1 = active 1 = active
ISR[7]—Input Port Change Status
In the timer mode, this bit is set once each cycle of the generated
square wave (every other time that the counter/timer reaches zero
count). The bit is reset by a stop counter command. The command,
however, does not stop the counter/timer.
This bit is a ‘1’ when a change-of-state has occurred at the IP0, IP1,
IP2, or IP3 inputs and that event has been selected to cause an
interrupt by the programming of ACR[3:0]. The bit is cleared when
the CPU reads the IPCR.
ISR[2]—Channel A Change in Break
ISR[6]—Channel B Change In Break
This bit, when set, indicates that the Channel A receiver has
detected the beginning or the end of a received break. It is reset
when the CPU issues a Channel A ‘reset break change interrupt’
command.
This bit, when set, indicates that the Channel B receiver has
detected the beginning or the end of a received break. It is reset
when the CPU issues a Channel B ‘reset break change interrupt’
command.
ISR[1]—RxA Interrupt
ISR[5]—RxB Interrupt
This bit indicates that the channel A receiver is interrupting
according to the fill level programmed by the MR0 and MR1
registers. This bit has a different meaning than the receiver
ready/full bit in the status register.
This bit indicates that the channel B receiver is interrupting
according to the fill level programmed by the MR0 and MR1
registers. This bit has a different meaning than the receiver
ready/full bit in the status register.
ISR[0]—TxA Interrupt
ISR[4]—TxB Interrupt
This bit indicates that the channel A transmitter is interrupting
according to the interrupt level programmed in the MR0[5:4] bits.
This bit has a different meaning than the Tx RDY bit in the status
register.
This bit indicates that the channel B transmitter is interrupting
according to the interrupt level programmed in the MR0[5:4] bits.
This bit has a different meaning than the Tx RDY bit in the status
register.
ISR[3]—Counter Ready.
In the counter mode, this bit is set when the counter reaches
terminal count and is reset when the counter is stopped by a stop
counter command.
IMR—Interrupt Mask Register
The programming of this register selects which bits in the ISR causes an interrupt output. If a bit in the ISR is a ‘1’ and the corresponding bit in
the IMR is also a ‘1’ the INTRN output will be asserted. If the corresponding bit in the IMR is a zero, the state of the bit in the ISR has no effect
on the INTRN output. Note that the IMR does not mask the programmable interrupt outputs OP3–OP7 or the reading of the ISR.
IMR INTERRUPT MASK REGISTER
Addr
IMR
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
INPUT
PORT
Delta
Break B
RxRDY/
FFULL B
TxRDY B
Counter
Ready
Delta
Break A
RxRDY/
FFULL A
TxRDY
A
CHANGE
0x05
0 = not
0 = not
0 = not
0 = not
0 = not
0 = not
0 = not
0 = not
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
1 = enabled
1 = enabled
1 = enabled
1 = enabled
1 = enabled
1 = enabled
1 = enabled
1 = enabled
33
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
IVR/GP – Interrupt Vector Register (68XXX mode) or General Purpose register (80XXX mode)
IVR/GP
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0x0C
Interrupt Vector Register (68XXX mode) or General Purpose register (80XXX mode)
This register stores the Interrupt Vector. It is initialized to 0x0F on hardware reset and is usually changed from this value during initialization of
the SC26L92. The contents of this register will be placed on the data bus when IACKN is asserted low or a read of address 0xC is performed.
When not operating in the 68XXX mode, this register may be used as a general purpose one byte storage register. A convenient use could be to
store a “shadow” of the contents of another SC28L92 register (IMR, for example).
CTPU and CTPL – Counter/Timer Registers
CTPU COUNTER TIMER PRESET UPPER
CTPU
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 1
BIT 0
BIT 0
0x06
The lower eight (8) bits for the 16 bit counter timer preset register
CTPL COUNTER -TIMER PRESET LOW
CTPL
Bit 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
0x07
The Upper eight (8) bits for the 16 bit counter timer preset register
The CTPU and CTPL hold the eight MSBs and eight LSBs,
respectively, of the value to be used by the counter/timer in either
the counter or timer modes of operation. The minimum value which
may be loaded into the CTPU/CTPL registers is H‘0002’. Note that
these registers are write-only and cannot be read by the CPU.
new values have not been loaded, the previous count values are
preserved and used for the next count cycle.
In the counter mode, the current value of the upper and lower 8 bits
of the counter (CTU, CTL) may be read by the CPU. It is
recommended that the counter be stopped when reading to prevent
potential problems which may occur if a carry from the lower 8 bits
to the upper 8 bits occurs between the times that both halves of the
counter are read. However, note that a subsequent start counter
command will cause the counter to begin a new count cycle using
the values in CTPU and CTPL.
In the timer mode, the C/T generates a square wave whose period is
twice the value (in C/T clock periods) of the CTPU and CTPL. The
waveform so generated is often used for a data clock. The formula
for calculating the divisor n to load to the CTPU and CTPL for a
particular 1X data clock is shown below.
n = (C/T Clock Frequency) divided by (2 x 16 x Baud rate desired)
When the C/T clock divided by 16 is selected, the maximum divisor
becomes 1,048,575.
Often this division will result in a non-integer number; 26.3, for
example. One can only program integer numbers in a digital divider.
Therefore, 26 would be chosen. This gives a baud rate error of
0.3/26.3 which is 1.14%; well within the ability asynchronous mode
of operation.
Output Port Notes
The output ports are controlled from four places: the OPCR
register,the OPR register, the MR registers and the command
register (except the 2681 and 68681) The OPCR register controls
the source of the data for the output ports OP2 through OP7. The
data source for output ports OP0 and OP1 is controlled by the MR
and CR registers. When the OPR is the source of the data for the
output ports, the data at the ports is inverted from that in the OPR
register.
The C/T will not be running until it receives an initial ‘Start Counter’
command (read at address A3–A0 = 1110). After this, while in timer
mode, the C/T will run continuously. Receipt of a start counter
command (read with A3–A0 = 1110) causes the counter to terminate
the current timing cycle and to begin a new cycle using the values in
CTPU and CTPL. If the value in CTPU and CTPL is changed, the
current half-period will not be affected, but subsequent half periods
will be affected.
The content of the OPR register is controlled by the “Set Output Port
Bits Command” and the “Reset Output Bits Command”. These
commands are at E and F, respectively. When these commands are
used, action takes place only at the bit locations where ones exist.
For example, a one in bit location 5 of the data word used with the
“Set Output Port Bits” command will result in OPR5 being set to one.
The OP5 would then be set to zero (V SS ). Similarly, a one in bit
position 5 of the data word associated with the “Reset Output Ports
Bits” command would set OPR5 to zero and, hence, the pin OP5 to
The counter ready status bit (ISR[3]) is set once each cycle of the
square wave. The bit is reset by a stop counter command (read with
A3–A0 = H’F’). The command however, does not stop the C/T. The
generated square wave is output on OP3 if it is programmed to be
the C/T output. In the counter mode, the value C/T loaded into
CTPU and CTPL by the CPU is counted down to 0.. Counting
begins upon receipt of a start counter command. Upon reaching
terminal count 0x0000, the counter ready interrupt bit (ISR[3]) is set.
The counter continues counting past the terminal count until stopped
by the CPU. If OP3 is programmed to be the output of the C/T, the
output remains High until terminal count is reached, at which time it
goes Low. The output returns to the High state and ISR[3] is cleared
when the counter is stopped by a stop counter command. The CPU
may change the values of CTPU and CTPL at any time, but the new
count becomes effective only on the next start counter commands. If
a one (V ).
DD
The CTS, RTS, CTS Enable Tx signals
CTS (Clear To Send) is usually meant to be a signal to the
transmitter meaning that it may transmit data to the receiver. The
CTS input is on pin IP0 for TxA and on IP1 for TxB. The CTS signal
is active low; thus, it is called CTSAN for TxA and CTSBN for TxB.
RTS is usually meant to be a signal from the receiver indicating that
the receiver is ready to receive data. It is also active low and is,
34
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
thus, called RTSAN for RxA and RTSBN for RxB. RTSAN is on pin
OP0 and RTSBN is on OP1. A receiver’s RTS output will usually be
connected to the CTS input of the associated transmitter. Therefore,
one could say that RTS and CTS are different ends of the same
wire!
the receiver that will be connected to the transmitter’s CTS input.
The receiver will set RTS high when the receiver FIFO is full AND
the start bit of the ninth or 17th character is sensed. Transmission
then stops with nine or 17 valid characters in the receiver. When
MR2(4) is set to one, CTSN must be at zero for the transmitter to
operate. If MR2(4) is set to zero, the IP pin will have no effect on
the operation of the transmitter. MR1(7) is the bit that allows the
receiver to control OP0. When OP0 (or OP1) is controlled by the
receiver, the meaning of that pin will be.
MR2(4) is the bit that allows the transmitter to be controlled by the
CTS pin (IP0 or IP1). When this bit is set to one AND the CTS input
is driven high, the transmitter will stop sending data at the end of the
present character being serialized. It is usually the RTS output of
RESETN
RESETN
t
RES
t
RES
80XXX Mode
68XXX Mode
SD00696
Figure 4. Reset Timing
A0–A3
CEN
t
t
AS
t
AH
t
CS
CH
t
t
RWD
RW
RDN
t
DD
t
DF
NOT
VALID
D0–D7
(READ)
FLOAT
VALID
FLOAT
t
RWD
WDN
t
DS
t
DH
D0–D7
(WRITE)
VALID
SD00087
Figure 5. Bus Timing (80XXX mode)
35
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
t
CSC
X1/CLK
t
AS
A1–A4
t
CS
t
CH
RWN
t
RWD
t
CSN
AH
t
t
DF
DD
NOT
VALID
D0–D7
DATA VALID
t
DA
DTACKN
t
DAH
t
DCR
t
DAT
NOTE: DACKN low requires two rising edges of X1 clock after CSN is low.
SD00687
Figure 6. Bus Timing (Read Cycle) (68XXX mode)
t
CSC
X1/CLK
t
AS
A1–A4
RWN
t
t
CH
CS
t
RWD
t
CSN
AH
D0–D7
t
DH
t
DS
DTACKN
t
t
DAH
DCW
t
DAT
NOTE: DACKN low requires two rising edges of X1 clock after CSN is low.
SD00688
Figure 7. Bus Timing (Write Cycle) (68XXX mode)
36
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
t
CSC
X1/CLK
INTRN
IACKN
t
t
DF
DD
D0–D7
t
CSD
t
DAL
DTACKN
t
t
DCR
DAH
t
DAT
NOTE: DACKN low requires two rising edges of X1 clock after CSN is low.
SD00149
Figure 8. Interrupt Cycle Timing (68XXX mode)
RDN
t
t
PH
PS
IP0–IP6
(a) INPUT PINS
WRN
t
PD
OP0–OP7
OLD DATA
NEW DATA
(b) OUTPUT PINS
SD00135
Figure 9. Port Timing
37
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
V
M
WRN
t
IR
1
INTERRUPT
V
+0.5V
OL
OUTPUT
V
OL
V
M
RDN
t
IR
1
INTERRUPT
V
+0.5V
OL
OUTPUT
V
OL
NOTES:
1. INTRN or OP3-OP7 when used as interrupt outputs.
2. The test for open-drain outputs is intended to guarantee switching of the output transistor. Measurement of this response is referenced from the midpoint of the switching
signal, V , to a point 0.5V above V . This point represents noise margin that assures true switching has occurred. Beyond this level, the effects of external circuitry and
M
OL
test environment are pronounced and can greatly affect the resultant measurement.
SD00136
Figure 10. Interrupt Timing (80xxx mode)
t
t
t
t
V
CLK
CTC
Rx
CC
NOTE:
RESISTOR REQUIRED
FOR TTL INPUT.
470Ω
Tx
X1/CLK
CTCLK
RxC
CLK
X1
TxC
t
t
t
t
CLK
CTC
Rx
X2*
*NOTE: X2 MUST BE LEFT OPEN.
SC28L92
Tx
3pF
PARASITIC CAPACITANCE
X1
2pF
C1
50kΩ
to
100kΩ
C2
4pF
X2
TO UART
CIRCUIT
3.6864MHz
3pF
PARASITIC CAPACITANCE
C1 = C2 24pF FOR C = 20pF
L
C1 and C2 should be chosen according to the crystal manufacturer’s specification.
C1 and C2 values will include any parasitic capacitance of the wiring and X1 X2 pins.
Gain at 3.6864MHz: 9 to 13 dB
Package capacitance approximately 4pF.
SD00695
Figure 11. Clock Timing
38
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
1 BIT TIME
(1 OR 16 CLOCKS)
TxC
(INPUT)
t
TXD
TxD
t
TCS
TxC
(1X OUTPUT)
SD00138
Figure 12. Transmitter External Clocks
RxC
(1X INPUT)
t
t
RXH
RXS
RxD
SD00139
Figure 13. Receiver External Clock
TxD
D1
D2
D3
BREAK
D4
D6
TRANSMITTER
ENABLED
TxRDY
(SR2)
WRN
D1
D8
D9
START
BREAK
D10
STOP
BREAK
D11 WILL
NOT BE
D12
WRITTEN TO
THE TxFIFO
1
CTSN
(IP0)
2
RTSN
(OP0)
OPR(0) = 1
OPR(0) = 1
NOTES:
1. Timing shown for MR2(4) = 1.
2. Timing shown for MR2(5) = 1.
SD00155
Figure 14. Transmitter Timing
39
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
D1
D2
D8
D9
D10
D11
D12
D13
RxD
D12, D13 WILL BE LOST
DUE TO RECEIVER DISABLE.
RECEIVER
ENABLED
RxRDY
(SR0)
FFULL
(SR1)
RxRDY/
FFULL
2
(OP5)
RDN
STATUS DATA
STATUS DATA STATUS DATA STATUS DATA
D11 WILL BE LOST
DUE TO OVERRUN
D1
D2
D3
D10
OVERRUN
(SR4)
RESET BY COMMAND
1
RTS
(OP0)
OPR(0) = 1
NOTES:
1. Timing shown for MR1(7) = 1.
2. Shown for OPCR(4) = 1 and MR(6) = 0.
SD00156
Figure 15. Receiver Timing
MASTER STATION
TxD
BIT 9
BIT 9
BIT 9
1
ADD#1
1
D0
0
ADD#2
TRANSMITTER
ENABLED
TxRDY
(SR2)
WRN
MR1(4–3) = 11
MR1(2) = 1
ADD#1 MR1(2) = 0 D0
MR1(2) = 1 ADD#2
PERIPHERAL STATION
BIT 9
BIT 9
1
BIT 9
0
BIT 9
BIT 9
0
0
ADD#1
D0
ADD#2 1
RxD
RECEIVER
ENABLED
RxRDY
(SR0)
RDN/WRN
MR1(4–3) = 11
ADD#1
STATUS DATA
STATUS DATA
ADD#2
D0
SD00096
Figure 16. Wake-Up Mode
40
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
I = 2.4mA
INTRN
DACKN
+5V
125pF
I = 2.4mA V return to V for a 0 level
OL
CC
I = 400µA V
return to V for a 1 level
SS
OH
D0–D7
TxDA/B
OP0–OP7
125pF
SD00690
Figure 17. Test Conditions on Outputs
41
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
PLCC44: plastic leaded chip carrier; 44 leads
SOT187-2
42
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
QFP44: plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm
SOT307-2
43
2000 Jan 21
Philips Semiconductors
Product specification
3.3V–5.0V Dual Universal Asynchronous
Receiver/Transmitter (DUART)
SC28L92
Data sheet status
[1]
Data sheet
status
Product
status
Definition
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Righttomakechanges—PhilipsSemiconductorsreservestherighttomakechanges, withoutnotice, intheproducts, includingcircuits,standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Copyright Philips Electronics North America Corporation 2000
All rights reserved. Printed in U.S.A.
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Date of release: 01-00
Document order number:
9397 750 06796
Philips
Semiconductors
相关型号：
SC28L92A1B/G,557
SC28L92 - 3.3 V/5.0 V Dual Universal Asynchronous Receiver/Transmitter (DUART) QFP 44-Pin
NXP
SC28L92A1B/N,557
SC28L92 - 3.3 V/5.0 V Dual Universal Asynchronous Receiver/Transmitter (DUART) QFP 44-Pin
NXP
SC28L92A1BS,528
IC 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC48, 6 X 6 MM, 0.85 MM HEIGHT, PLASTIC, SOT-778-4, HVQFN-48, Serial IO/Communication Controller
NXP
SC28L92A1BS,557
IC 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC48, 6 X 6 MM, 0.85 MM HEIGHT, PLASTIC, SOT-778-4, HVQFN-48, Serial IO/Communication Controller
NXP
©2020 ICPDF网 联系我们和版权申明