SL3S1004FUDBG1 [NXP]
UCODE 7xm and UCODE 7xm;型号: | SL3S1004FUDBG1 |
厂家: | NXP |
描述: | UCODE 7xm and UCODE 7xm |
文件: | 总33页 (文件大小:591K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SL3S1004_1014
UCODE 7xm and UCODE 7xm+
Rev. 3.2 — 27 July 2016
325032
Product data sheet
COMPANY PUBLIC
1. General description
The UCODE 7xm series is the latest generation of NXP’s memory UHF tag ICs. With the
leading-edge read range UCODE 7xm is well suited for applications which require high
read range and also demanding an extended user memory to store data specific to
customer or products. UCODE 7xm offers an user memory of 1-kbit, whereas UCODE
7xm+ supports 2-kbit user memory and a 384-bit digital signature.
Both products incorporate features known from UCODE 7 like pre-serialization, tag power
indicator as well as the product status flag.
There are numbers of applications where the combination of high read range and user
memory is needed, such as:
• Inventory and supply chain management
• Process optimization (e.g in the automotive industry)
• Brand protection/authentication (e.g. expensive wines or branded luxury fashion
items)
• Automatic vehicle ID where no cryptography is required
• Asset tracking (e.g. for high value assets)
2. Features and benefits
2.1 Key features
Read sensitivity 19 dBm
Write sensitivity 12 dBm
Encoding speed: 32 bits per 1.5 milliseconds
Up to 2-kbit user memory
Digital signature
Standard functionality
Untraceable feature
Tag Power Indicator
Pre-serialization for 96-bit EPC
Integrated Product Status Flag (PSF)
Parallel encoding mode
According to EPCglobal v1.2.0
Compatible with single-slit antenna
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
2.1.1 Memory
Up to 448-bit of EPC memory
Supports Pre-serialization for 96-bit EPC
96-bit Tag IDentifier (TID) factory locked
48-bit unique serial number factory-encoded into TID
1-kbit user memory for UCODE 7xm
2-kbit user memory for UCODE 7xm+
384-bit digital signature in UCODE 7xm+
32-bit kill password to permanently disable the tag
32-bit access password
Wide operating temperature range: 40 C up to +85 C
Minimum 100.000 write cycle endurance
Data retention 20 years
2.2 Key benefits
2.2.1 End user benefit
Extended user memory of up to 2-kbit
Brand protection feature using digital signature
Long read/write ranges due to leading edge chip sensitivity
Reliable operation in dense reader and noisy environments through high interference
rejection
2.2.2 Antenna design benefits
High sensitivity enables smaller and cost efficient antenna designs
Selected chip impedance enables re-use of antenna designs from UCODE 7
2.2.3 Label/module manufacturer benefit
Large RF pad-to-pad distance to ease antenna design
Symmetric RF inputs are less sensitive to process variation
Single-slit antenna for a more mechanically stable antenna connection
Pre-serialization of the 96-bit EPC
Extremely fast encoding of the EPC content
2.3 Supported features
All mandatory commands of EPCglobal v1.2.0 specification are implemented
The following optional commands are implemented:
Access
BlockPermalock (block size of 256-bit)
32-bit BlockWrite
Implemented custom commands and features:
Untraceable
ReadSignature
Product Status Flag bit: enables the UHF RFID tag to be used as EAS
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
2 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
(Electronic Article Surveillance) tag without the need for a back-end data base.
Tag Power Indicator: enables the reader to select only ICs/tags that have enough
power to be written to.
Parallel encoding: allows for the ability to bring (multiple) tag(s) quickly to the
OPEN state and hence allowing single tags to be identified simply, without timing
restrictions, or multiple tags to be e.g. written to at the same time, considerably
reducing the encoding process
UCODE 7xm can be used in combination with readers compliant with EPCglobal v1.2.0
standard. For access to full UCODE 7xm family functionality firmware upgrade of the
reader may be necessary.
3. Applications
3.1 Markets
Logistics
Brand protection (luxury branded fashion goods)
Process automation
3.2 Applications
Inventory and supply chain management
Asset tracking
Process optimization(e.g in the automotive industry)
Automatic vehicle ID where no cryptography is required
Brand protection/authentication (e.g. expensive wines or branded luxury fashion
items)
Parking access
Fleet management
Loss prevention
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
IC type
Description
Version
SL3S1004FUD/BG1 Wafer
UCODE 7xm Gold bumped die on sawn 8” 120 m wafer with 7 m not applicable
Polyimide spacer;
SL3S1014FUD/BG1 Wafer
UCODE 7xm+ Gold bumped die on sawn 8” 120 m wafer with 7 m not applicable
Polyimide spacer;
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
3 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
5. Block diagram
The UCODE 7xm/7xm+ consists of three major blocks:
- Analog Interface
- Digital Control
- EEPROM
The analog part provides stable supply voltage and demodulates data received from the
reader which is then processed by the digital part. Further, the modulation transistor of the
analog part transmits data back to the reader.
The digital control includes the state machines, processes the protocol and handles
communication with the EEPROM, which contains the EPC and the user data.
ANALOG
RF INTERFACE
DIGITAL CONTROL
ANTICOLLISION
EEPROM
VREG
VDD
RF1
READWRITE
CONTROL
data
in
RECT
RF2
DEMOD
MOD
MEMORY
antenna
ACCESS CONTROL
data
out
R/W
EEPROM INTERFACE
CONTROL
RF INTERFACE
CONTROL
SEQUENCER
CHARGE PUMP
aaa-005856
Fig 1. Block diagram of UCODE 7xm/7xm+ ICs
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
4 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
6. Pinning information
RF2
RF1
NXP trademark
TP1
TP2
aaa-017985
Fig 2. Pinning bare die
6.1 Pin description
Table 2.
Symbol
TP1
Pin description bare die
Description
test pad 1
RF1
antenna connector 1
test pad 2
TP2
RF2
antenna connector 2
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
5 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
7. Wafer layout
7.1 Wafer layout
(1)
RF2
RF1
(5)
Y
(6)
(4)
X
(7)
TP1
TP2
(8)
(2)
(3)
not to scale!
aaa-017986
(1) Die to Die distance (metal sealring - metal sealring) 21,4 m, (X-scribe line width: 15 m)
(2) Die to Die distance (metal sealring - metal sealring) 21,4 m, (Y-scribe line width: 15 m)
(3) Chip step, x-length: 585m
(4) Chip step, y-length: 645 m
(5) Bump to bump distance X (RF1 - RF2): 480 m
(6) Bump to bump distance Y (TP1 - RF2): 540 m
(7) Distance bump to metal sealring X: 41,8m (outer edge - top metal)
(8) Distance bump to metal sealring Y: 41,8 m
Bump size X x Y: 60 m x 60 m
Remark: TP1 and TP2 are electrically disconnected after dicing
Fig 3. UCODE 7xm/7xm+ wafer layout
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
6 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
8. Mechanical specification
The UCODE 7xm/7xm+ wafers are available in 120 m thickness with 7m Polyimide
spacer, resulting in less coupling between the antenna and the active circuit.
8.1 Wafer specification
See Ref. 4 “Data sheet - Delivery type description – General specification for 8” wafer on
UV-tape with electronic fail die marking, BU-ID document number: 1093**”.
8.1.1 Wafer
Table 3. Specifications
Wafer
Designation
each wafer is scribed with batch number and
wafer number
Diameter
200 mm (8”) unsawn - 205 mm typical sawn
on foil
Thickness
120 m 15 m
Number of pads
Pad location
4
non diagonal / placed in chip corners
Distance pad to pad RF1-RF2
Distance pad to pad TP1-RF2
Process
480.0 m
540.0 m
CMOS 0.14 m
25 wafers
77.773
Batch size
Potential good dies per wafer
Wafer backside
Material
Si
Treatment
ground and stress release
Ra max. 0.5 m, Rt max. 5 m
Roughness
Chip dimensions
Die size excluding scribe
Scribe line width:
0.570 mm 0.630 mm = 0.359 mm2
x-dimension = 15 m
y-dimension = 15 m
Passivation on front
Type
Sandwich structure
Material
PE-Nitride (on top)
Thickness
1.75 m total thickness of passivation
7 m 1 m
Polyimide spacer
Au bump
Bump material
Bump hardness
Bump shear strength
Bump height
> 99.9 % pure Au
35 – 80 HV 0.005
> 70 MPa
25 m[1]
Bump height uniformity
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
7 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
Table 3. Specifications
within a die
2 m
3 m
4 m
1.5 m
– within a wafer
– wafer to wafer
Bump flatness
Bump size
60 60 m
60 60 m
5 m
– RF1, RF2
– TP1, TP2
Bump size variation
[1] Because of the 7 m spacer, the bump will measure 18 m relative height protruding the spacer.
8.1.2 Fail die identification
No inkdots are applied to the wafer.
Electronic wafer mapping (SECS II format) covers the electrical test results and
additionally the results of mechanical/visual inspection.
See Ref. 4 “Data sheet - Delivery type description – General specification for 8” wafer on
UV-tape with electronic fail die marking, BU-ID document number: 1093**”
8.1.3 Map file distribution
See Ref. 4 “Data sheet - Delivery type description – General specification for 8” wafer on
UV-tape with electronic fail die marking, BU-ID document number: 1093**”
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
8 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9. Functional description
9.1 Air interface standards
The UCODE 7xm/7xm+ fully supports all mandatory parts of the EPCglobal v1.2.0
specification.
9.2 Power transfer
The interrogator provides an RF field that powers the tag, equipped with a UCODE
7xm/7xm+ IC. The antenna transforms the impedance of free space to the chip input
impedance in order to get the maximum possible power for the UCODE 7xm/7xm+ on the
tag.
The RF field, which is oscillating on the operating frequency provided by the interrogator,
is rectified to provide a rectified DC voltage to the analog and digital modules of the IC.
The antenna attached to the chip may use a DC connection between the two antenna
pads. Therefore the UCODE 7xm/7xm+ also enables loop antenna design.
9.3 Data transfer
9.3.1 Interrogator to tag Link
An interrogator transmits information to the UCODE 7xm/7xm+ by modulating a UHF RF
signal. The UCODE 7xm/7xm+ receives both information and operating energy from this
RF signal. Tags are passive, meaning that they have no battery and receive all of their
operating energy from the interrogator's RF waveform.
An interrogator is using a fixed modulation and data rate for the duration of at least one
inventory round. It communicates to the UCODE 7xm/7xm+ by modulating an RF carrier.
For further details refer to Ref. 1.
9.3.2 Tag to interrogator Link
Upon transmitting a valid command an interrogator receives information from a UCODE
7xm/7xm+ tag by transmitting an un-modulated RF carrier and listening for a
backscattered reply. The UCODE 7xm/7xm+ backscatters by switching the reflection
coefficient of its antenna between two states in accordance with the data being sent. For
further details refer to Ref. 1.
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
9 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.4 UCODE 7xm and UCODE 7xm+ Overview
This table should provide a quick overview on the features implemented in UCODE 7xm
and UCODE 7xm+. Details on the features are described in the following paragraphs.
Table 4.
Overview of UCODE 7xm and UCODE 7xm+
Features
UCODE 7xm
1024 bit
max 448 bit
96 bit
32 bit
32 bit
yes
UCODE 7xm+
2048 bit
max 448 bit
96 bit
32 bit
32 bit
yes
User Memory
EPC Memory
TID Memory
Access Password
Kill Password
PSF (Product Status Flag)
BlockWrite (32 bit)
yes
yes
BlockPermalock (256 bit block size)
Pre-Serialization of 96-bit EPC
Parallel Encoding
yes
yes
yes
yes
yes
yes
Backscatter strength reduction
Tag Power Indicator
Untraceable feature
Digital Signature (384-bit)
yes
yes
yes
yes
yes
yes
-
yes
9.5 Supported commands
The UCODE 7xm/7xm+ support all mandatory EPCglobal v1.2.0 commands.
In addition the following optional commands are supported:
• Access
• BlockPermalock (256 bit block size)
• BlockWrite (max 32 bit on even addresses only)
UCODE 7xm/7xm+ also offers the following custom commands:
• Untraceable
• ReadSignature (UCODE 7xm+ only)
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
10 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.5.1 Custom commands
9.5.1.1 Untraceable
The Untraceable function allows the UCODE 7xm/7xm+ to hide the complete or parts of
the EPC, TID and/or user memory. In addition the read range can be completely or
temporarily reduced.
This command can only be executed from the secured state.
Memory parts which are set untraceable are acting as non-existing.
EPC-field:
Specifies the number of words of the EPC memory which the UCODE 7xm/xm+ back
scatters. A change of this field therefore also changes the L bit in the Protocol Control
(PC) word.
TID-field:
Hide some (“01”) will hide the TID memory from address 20h (included) onwards.
Range-field:
In case of activated range toggling the read range reduction toggles from the actual value
to the second. (e.g. when actual state is normal it toggles to reduced). In case of power
loss the chip reverts to it’s prior state
UCODE 7xm/7xm+ does not support the U bit and therefore ignores this value.
Table 5.
Untraceable command
Command RFU U
No. of bits 16
EPC
TID
User
Range
RN
CRC
2
1
6
2
1
2
16
16
Description 11100010 00
0000 0000
don’t MSB:
care “0”:
“00”: hide none “0”: view “00”: normal handle CRC-16
“01”: hide some “1”: hide “01”: toggle
show memory above
EPC
“10”: hide all
“11”: RFU
“10”: reduced
“11”: RFU
“1”:
hide memory above
EPC
5 LSBs:
New EPC length
Table 6.
Untraceable command-response table
Starting State
Condition
Response
Next State
ready
ready
all
all
-
-
arbitrate, reply,
acknowledged
arbitrate
open
all
-
open
secured
killed
executable
all
backscatter header when done secured
killed
-
In case of an access to the tag the error condition “memory overrun” will be returned.
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
11 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.5.1.2 ReadSignature (UCODE 7xm+ only)
The ReadSignature command allows the read out of the pre-programmed Digital
Signature and includes a CRC-16 calculated over the whole command, the handle and
the a frame-sync.
Table 7.
ReadSignature command
Command
WordPtr
WordCount
RN
CRC
16
No. of bits
16
EVB
8
16
Description 1110 0000 0000 1000 Starting
Number of words to read
Handle
CRC-16
Address
Pointer
Table 8.
Tag reply to a successful ReadSignature command
Header
Signature Words
Variable
RN
CRC
No. of bits
1
0
16
16
Description
Digital Signature
Handle
CRC-16
The error Response “memory overrun” is returned in case WordCount=0 or in case
WordPtr or the combination of WordPtr and WordCountexceeds exceeds the range of the
Digital Signature.
Table 9.
ReadSignature command-response table
Starting State
Condition
Response
Next State
ready
ready
all
all
-
-
arbitrate, reply,
acknowledged
arbitrate
open
all
all
all
backscatter data
open
secured
killed
backscatter data
-
secured
killed
Digital Signature
The UCODE 7xm+ is delivered with a factory pre-programmed 384-bit Digital Signature
based on the Elliptic Curve Digital Signature Algorithm (ECDSA) using a 192-bit
cryptographic key. The parameters of the curve are according NIST P-192 (secp 192r1).
The data digital signed is the 96-bit TID of the UCODE 7xm+.
Verification of the digital signature:
After issuing the ReadSignature command the tag will return the 384-bit digital signature.
With the knowledge of the Public Key and the algorithm a verification that the silicon is an
origin NXP Semiconductors can be made.
UCODE 7xm+ Public Key:
04A72DB4B83233DD9A9711DB071281F14451747F815EEB111F1D4CD3DCAD60250C
830CD287DCEC0B39C76262BA998B7E01
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
12 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
MS VC++ Code Example
/**
* Check Originality Signature on curve NID_X9_62_prime192v1
**/
unsigned char CheckOriginalitySignature192UCode7xmBinary(unsigned char * aUid,
unsigned char * aSignature)
{
/* secp192v1 => ECC_Length=24; */
unsigned int ECC_Length = 24;
unsigned int bLength = 12;
char* publickey_str =
“04A72DB4B83233DD9A9711DB071281F14451747F815EEB111F1D4
CD3DCAD60250C830CD287DCEC0B39C76262BA998B7E01"; /* UCODE7xm */
BIGNUM *pk_bignum = BN_new();
EC_POINT *public_key = NULL;
/* Create a EC_KEY for specified curve */
EC_KEY *pubKey = EC_KEY_new_by_curve_name(NID_X9_62_prime192v1);
const EC_GROUP *ecgroup = EC_KEY_get0_group(pubKey);
ECDSA_SIG *signature = ECDSA_SIG_new();
unsigned char r[24]; /* ECC_Length */
unsigned char s[24]; /* ECC_Length */
char r_dest[24*2+1]; /* ECC_Length *2 +1 */
char s_dest[24*2+1]; /* ECC_Length *2 +1 */
unsigned int loop = 0;
if (signature == NULL )
{
return 1;
}
if (pubKey == NULL)
{
printf("Creation of PubKey failed \n");
return 1;
}
/* Convert the hex public key x,y co-ordinates to BIGNUM */
BN_hex2bn(&pk_bignum, publickey_str);
public_key = EC_POINT_bn2point(ecgroup, pk_bignum, NULL, NULL);
/* Set the public key point to EC_KEY */
EC_KEY_set_public_key(pubKey, public_key);
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
13 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
/* Extract the r and s part of the signature*/
memcpy(r, aSignature, ECC_Length);
memcpy(s, aSignature+ECC_Length, ECC_Length);
/* BIGNUM conversion function expects r in ASCII value */
for(loop = 0;loop < ECC_Length; loop++)
{
sprintf_s((r_dest+(loop*2)), 3, "%02X", r[loop]);
sprintf_s((s_dest+(loop*2)), 3, "%02X", s[loop]);
}
BN_hex2bn(&signature->r, r_dest);
BN_hex2bn(&signature->s, s_dest);
/*Signature verification for the UID sent*/
if (ECDSA_do_verify(aUid, bLength, signature, pubKey) == 1)
{
printf("\nSignature verified successfully\n\n");
return 0;
}
else
{
printf("\nSignature verification failed\n\n");
return 1;
}
}
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
14 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.6 UCODE 7xm/7xm+ memory
The UCODE 7xm/7xm+ memory is implemented according EPCglobal v1.2.0 and
organized in four banks:
Table 10. UCODE 7xm memory sections
Name
Size
Bank
00b
01b
10b
11b
Reserved memory (32 bit ACCESS and 32 bit KILL password)
EPC (excluding CRC, PC)
64 bit
448 bit
96 bit
1024bit
TID (including permalocked unique 48 bit serial number)
User Memory
Table 11. UCODE 7xm+ memory sections
Name
Size
Bank
00b
01b
10b
11b
Reserved memory (32 bit ACCESS and 32 bit KILL password)
EPC (excluding CRC, PC)
64 bit
448 bit
96 bit
2048bit
TID (including permalocked unique 48 bit serial number)
User Memory
The logical address of all memory banks begin at zero (00h).
In addition to the four memory banks a configuration word to handle the UCODE
7xm/7xm+ specific features is available at address 200h in the EPC memory. The
configuration word is described in detail in Section 9.7.1 “UCODE 7xm/7xm+ features
control mechanism”.
The TID complies to the extended tag Identification scheme according GS1 EPC Tag Data
Standard 1.9. (Ref. 2)
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
15 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.6.1 UCODE 7xm/7xm+ overall memory map
Table 12. UCODE 7xm/7xm+ overall memory map
Bank
address
Memory
address
Type
Content
Initial
Remark
Bank 00
00h to 1Fh
20h to 3Fh
00h to 0Fh
reserved
reserved
EPC
kill password
access password
CRC-16
all 00h
all 00h
unlocked memory
unlocked memory
Bank 01
EPC
memory mapped
calculated CRC
10h to 14h
15h
EPC
EPC
EPC
EPC
EPC length
UMI
00110b
1b
unlocked memory
locked memory
hardwired to 0
unlocked memory
unlocked memory
locked memory
locked memory
Action bit[4]
16h
XPC indicator
0b
17h to 1Fh
numbering system indicator 00h
[1]
20h to 1DFh EPC
EPC
Bank 01
ConfigWord
200h
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
EPC
TID
RFU
0b
201h
RFU
0b
202h
Parallel encoding
0b
203h
RFU
0b
locked memory
Action bit[4]
204h
Tag Power Indicator
0b
205h
RFU
0b
locked memory
locked memory
locked memory
locked memory
permanent bit[5]
locked memory
locked memory
locked memory
locked memory
locked memory
Permanent bit[5]
locked memory
locked memory
locked memory
locked memory
locked memory
locked memory
206h
RFU
0b
207h
RFU
0b
208h
RFU
0b
209h
max. backscatter strength
1b
20Ah
RFU
0b
20Bh
RFU
0b
20Ch
RFU
0b
20Dh
RFU
0b
20Eh
RFU
0b
20Fh
PSF alarm flag
allocation class identifier
0b
Bank 10
TID
00h to 07h
08h to 13h
14h
1110 0010b
TID
tag mask designer identifier 806h
TID
config word indicator
tag model number
XTID header
1b[2]
14h to 1Fh
20h to 2Fh
30h to 5Fh
TID
TMNR[3]
2000h
SNR
TID
TID
serial number
Bank 11
USER
000h to 3FFh USER
User Memory
undefined
locked memory
UCODE 7xm and 7xm+
400h to 7FFh USER
User Memory
undefined
locked memory
UCODE 7xm+ only
[1] HEX E280 6000 0000 nnnn nnnn nnnn
where n are the nibbles of the 48-bit SNR of the TID
[2] Indicates the existence of a Configuration Word at the end of the EPC number
[3] See Figure 4
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
16 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
[4] Action bits: meant to trigger a feature upon a SELECT command on the related bit ref feature control
mechanism, seeSection 9.7.1
[5] Permanent bit: permanently stored bits in the memory; Read/Writeable according to EPC bank lock status,
see Section 9.7.1
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
17 of 33
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
9.6.2 UCODE 7xm/7xm+ TID memory details
Model Number
Mask
First 48 bit of TID
memory
Config
Word
Class ID
Designer
ID
Sub
Version
XTID
Header
Version Nr. (Silicon) Nr.
Indicator
UCODE 7xm
E2C06D12
E2C06D92
E2h
E2h
C06h
C06h
1b
1b
1010b
1011b
0010010b
0010010b
2000h
2000h
UCODE 7xm+
Addresses 00h
5Fh
TID
MS Byte
LS Byte
MSBit
LSBit
MSBit
LSBit
5Fh
Bit
Address
00h
07h 08h
13h 14h
1Fh 20h
2Fh 30h
Class Identifier
Mask-Designer Identifier
Model Number
XTID
Serial Number
11
15
Bits
7
0
11
0
0
0
47
0
E2h
(EAN.UCC)
C06h
(NXP; with XTID)
D12h
(UCODE 7xm)
2000h
(indication of 48bit
unique SNR)
000000000000h to FFFFFFFFFFFFh
Address 14h
18h 19h
1Fh
S.
I.
Sub Version Number
1010b
Model Number
B.
Bits
0
3
6
0
0
1b
0010010b
(UCODE 7xm)
aaa-017987
Fig 4. UCODE 7xm/7xm+ TID memory structure
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.7 Supported features
The UCODE 7xm/7xm+ is equipped with features of previous UCODE generation. These
include:
- Pre-serialization of the 96-bit EPC
- Parallel encoding
- Tag Power Indicator
- Backscatter strength reduction
- Product Status Flag (PSF)
- Single-slit antenna solution
These features are implemented in such a way that standard EPCglobal v1.2.0 READ /
WRITE / ACCESS / SELECT commands can be used to operate these features.
The Configuration Word, as mentioned in the memory map, describes the additional
features located at address 200h of the EPC memory.
Bit 14h of the TID indicates the existence of a Configuration Word. This flag will enable the
selection of configuration word enhanced transponders in mixed tag populations.
9.7.1 UCODE 7xm/7xm+ features control mechanism
The different features of the UCODE 7xm/7xm+ can be activated / de-activated by
addressing or changing the content of the corresponding bit in the configuration word
located at address 200h in the EPC memory bank (see Table 13). The de-activation of the
action bit features will only happen after chip reset.
Table 13. Configuration word UCODE 7xm/7xm+
Locked memory
Action bit
Locked memory Action bit
Locked memory
RFU
RFU
Parallel
encoding
RFU
Tag Power
Indicator
RFU
RFU
RFU
0
1
2
3
4
5
6
7
Table 14. Configuration word UCODE 7xm/7xm+
Locked Permanent
memory bit
Locked memory
Permanent
bit
RFU
max.
RFU
RFU
RFU
RFU
RFU
PSF Alarm bit
backscatter
strength
8
9
10
11
12
13
14
15
The configuration word contains 2 different type of bits:
• Action bits: meant to trigger a feature upon a SELECT command on the related bit:
Parallel encoding
Tag Power indicator
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
19 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
• Permanent bits: permanently stored bits in the memory
Max. Backscatter Strength
PSF Alarm bit
The activation or the de-activation of the feature behind the permanent bits happens only
when attempting to write a “1” value to the related bit (value toggling) - writing “0” value
will have no effect.
If the feature is activated, the related bit will be read with a “1” value and, if de-activated,
with a “0” value.
The permanent bits can only be toggled by using standard EPC WRITE (not a BlockWrite)
if the EPC bank is unlocked or within the SECURED state if the EPC is locked. If the EPC
is permalocked, they cannot be changed.
Action bits will trigger a certain action only if the pointer of the SELECT command exactly
matches the action-bit address (i.e. 202h or 204h), if the length=1 and if mask=1b
(no multiple trigger of actions possible within one single SELECT command).
After issuing a SELECT to any action bits an interrogator shall transmit CW for RTCal
Ref. 3 + 80 s before sending the next command.
If the truncate bit in the SELECT command is set to "1" the SELECT will be ignored.
A SELECT on action bits will not change the digital state of the chip.
The action bits can be triggered regardless if the EPC memory is unlocked, locked or
permalocked.
9.7.2 Backscatter strength reduction
The UCODE 7xm/7xm+ features two levels of backscatter strengths. Per default
maximum backscatter is enabled in order to enable maximum read rates. When clearing
the flag the strength can be reduced if needed.
9.7.3 Automatic self pre-serialization of the 96-bit EPC
Description
The 96-bit EPC, which is the initial EPC length settings of UCODE 7xm/7xm+, will be
delivered pre-serialized with the 48-bit serial number from the TID.
Use cases and benefits
With a pre-serialized EPC, the encoding process of the tags with UCODE 7xm/7xm+ gets
simpler and faster as it only needs to encode the SKU (58-bit header of the EPC).
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
20 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.7.4 Parallel encoding
Description
This feature of the UCODE 7xm/7xm+ can be activated by the “Parallel encoding bit” in
the Configuration-Word located at (202h).
Upon issuing a EPC SELECT command on the “Parallel encoding bit”, in a population of
UCODE 7xm/7xm+ tags, a subsequent QUERY brings all tags go the OPEN state with a
specific handle (“AAAAh”).
Once in the OPEN state, for example a WRITE command will apply to all tags in the
OPEN state (see Figure 6). This parallel encoding is considerably lowering the encoding
time compared to a standard implementation (see Figure 5).
The amount of tags that can be encoded at the same time will depend on the strength of
the reader signal. Since all tags will backscatter their ACKNOWLEDGE (ACK) response
at the same time, the reader will observe collision in the signal from the tags.
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
21 of 33
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
QUERY/Adjust/Rep
QUERY/Adjust/Rep
READER
(16-bit)
(16-bit)
TAG 1
Tags
TAG 2
Only TAG 1 is being addressed
Only TAG 2 is being addressed
aaa-006843
Fig 5. Example of 16-bit Write command with standard EPC Gen 2 commands
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
SELECT on
Parallel
QUERY (Q=0)
encoding bit
(16-bit)
READER
TAG 1
TAG 2
Tags
TAG n
All UCODE 7xm/7xm+ tags receive the Command
aaa-017990
Fig 6. Illustration of Parallel encoding for 16-bit Write command
Use cases and benefits
Parallel encoding feature of UCODE 7xm/7xm+ can enable ultra fast bulk encoding.
Taking in addition advantage of the pre-serialization scheme of UCODE 7xm/7xm+, the
same SKU can be encoded in multiple tags as the EPC will be delivered pre-serialized
already.
In the case of only one tag answering (like in printer encoding), this feature could be used
to save some overhead in commands to do direct EPC encoding after the handle reply.
Since this is a custom specific feature of UCODE 7xm/7xm+ (taken over from our
previous UHF tag IC UCODE 7/7m) the use of this features requires the same support on
the reader side as for previous UCODE products.
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
23 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.7.5 Tag Power Indicator
Description
Upon a SELECT command on the “Tag Power Indicator”, located in the config word 204h,
an internal power check on the chip is performed to see if the power level is sufficient to
perform a WRITE command. The decision level is defined as nominal WRITE sensitivity
minus 1dB. In the case there is enough power, the SELECT command is matching and
non-matching if not enough power. The tag can then be singulated by the standard
inventory procedure.
Use cases and benefits
This feature gives the possibility to select only the tag(s) that receive enough power to be
written during e.g. printer encoding in a dense environment of tags even though the
reader may read more than one tag (see Figure 7 for illustration). The power level still
needs to be adjusted to transmit enough writing power to one tag only to do one tag
singulation.
Power level for READ/WRITE
too low/too low
OK/too low
OK/too low
Only this tag will select itself
OK/OK
OK/too low
OK/too low
too low/too low
aaa-005662
Fig 7. Selection of tags with Tag Power Indicator feature
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
24 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
9.7.6 Product Status Flag (PSF)
Description
The PSF is a general purpose bit located in the Configuration word at address 20Fh with a
value that can be freely changed.
Use cases and benefits
The PSF bit can be used as an EAS (Electronic Article Surveillance) flag, quality checked
flag or similar.
In order to detect the tag with the PSF activated, a EPC SELECT command selecting the
PSF flag of the Configuration word can be used. In the following inventory round only PSF
enabled chips will reply their EPC number.
9.7.7 Single-slit antenna solution
Description
In UCODE 7xm/7xm+ the test pads TP1 and TP2 are electrically disconnected meaning
they are not electrically active and can be safely short-circuited to the RF pads RF1 and
RF2 (see Figure 8).
Standard assembly
Single-slit assembly
Supporting pads
aaa-005857
Fig 8. Standard antenna design versus single-slit antenna
Uses cases and benefits
Using single-slit antenna enables easier assembly and antenna design. Inlay
manufacturer will only have to take care about one slit of the antenna instead of two in
case all pads need to be disconnected from each other.
Additionally single-slit antenna assembly and the related increased input capacitance (see
Table 16) can be used advantageously over the standard antenna design as additional
room for optimization to different antenna design.
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
25 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
10. Limiting values
Table 15. Limiting values[1][2]
In accordance with the Absolute Maximum Rating System (IEC 60134).
Voltages are referenced to RFN
Symbol
Parameter
Conditions
Min
Max
Unit
Bare die limitations
Tstg
storage temperature
55
40
-
+125
+85
2
C
C
kV
Tamb
VESD
ambient temperature
[3]
electrostatic discharge
voltage
Human body model
Pad limitations
Pi input power
maximum power
-
100
mW
dissipation, RFP pad
[1] Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any conditions other
than those described in the Operating Conditions and Electrical Characteristics section of this specification
is not implied.
[2] This product includes circuitry specifically designed for the protection of its internal devices from the
damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be
taken to avoid applying greater than the rated maxima.
[3] For ESD measurement, the die chip has been mounted into a CDIP20 package.
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
26 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
11. Characteristics
11.1 UCODE 7xm/7xm+ bare die characteristics
Table 16. UCODE 7xm/7xm+ RF interface characteristics (RF1, RF2)
Symbol
fi
Parameter
Conditions
Min
Typ
-
Max
Unit
MHz
dBm
dBm
dBm
input frequency
840
960
[1][3][8]
[2]
Pi(min)
Pi(min)
Pi(min)
minimum input power
minimum input power
minimum input power
READ sensitivity
WRITE sensitivity
-
-
-
18.5
12
7
-
-
-
[2]
Reduced operating
range
[5]
t
encoding speed (16b-bit or 32-bit)
chip input capacitance
chip impedance
16-bit
-
-
-
-
-
-
-
1.5
-
-
-
-
-
ms
pF
[3][4]
[3][4]
[3][4]
[3][4]
[6]
Ci
Z
parallel
0.63
866 MHz
915 MHz
953 MHz
915 MHz
19-j284
17-j274
17-j265
26-j235
16-j181
Z
Z
typical assembled impedance [9]
typical assembled impedance [9] in 915 MHz
case of single-slit antenna assembly
[6][7]
-
-
Tag Power Indicator mode
Pi(min) minimum input power level to be
able to select the tag
[2]
-
11
dBm
[1] Power to process a QUERY command
[2] Tag sensitivity on a 2dBi gain antenna
[3] Measured with a 50 source impedance directly on the chip
[4] At minimum operating power
[5] When the memory content is “0000...”.
[6] The antenna shall be matched to this impedance
[7] Depending on the specific assembly process, sensitivity losses of few tenths of dB might occur
[8] Results in approximately -19dBm tag sensitivity with a 2dBi gain antenna
[9] Assuming a 80fF additional input capacitance, 250fF in case of single slit antenna
Table 17. UCODE 7xm/7xm+ memory characteristics
Symbol
Parameter
Conditions
Min
Typ
Max Unit
EEPROM characteristics
tret
retention time
Tamb 55 C
20
-
-
-
-
year
Nendu(W)
write endurance
100k
cycle
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
27 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
12. Package outline
This section is not applicable for this kind of device.
13. Packing information
13.1 Wafer
See Ref. 4 “Data sheet - Delivery type description – General specification for 8” wafer on
UV-tape with electronic fail die marking, BU-ID document number: 1093**”
14. Abbreviations
Table 18. Abbreviations
Acronym
CRC
Description
Cyclic Redundancy Check
CW
Continuous Wave
DSB-ASK
DC
Double Side Band-Amplitude Shift Keying
Direct Current
EAS
Electronic Article Surveillance
Electrically Erasable Programmable Read Only Memory
EEPROM
EPC
Electronic Product Code (containing Header, Domain Manager, Object Class
and Serial Number)
FM0
G2
Bi phase space modulation
Generation 2
IC
Integrated Circuit
PIE
PSF
RF
Pulse Interval Encoding
Product Status Flag
Radio Frequency
UHF
SECS
TID
Ultra High Frequency
Semi Equipment Communication Standard
Tag IDentifier
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
28 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
15. References
[1] GS1 EPCglobal: EPC™ Radio-Frequency Identity Protocols Class-1 Generation-2
UHF RFID Protocol for Communications at 860 MHz – 960 MHz, Version 1.2.0 (23
October 2008)
[2] EPCglobal: EPC Tag Data Standard Version 1.9, ratified Nov-2014
[3] RTCal is the Interrogator-to-Tag calibration symbol length defined in the EPCglobal
specification
[4] Data sheet - Delivery type description – General specification for 8” wafer on
UV-tape with electronic fail die marking, BU-ID document number: 1093**1
1. ** ... document version number
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
29 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
16. Revision history
Table 19. Revision history
Document ID
Release date
20160727
Data sheet status
Change notice Supersedes
SL3S1004_1014 v.3.2
Modifications:
Product data sheet
-
-
-
SL3S1004_1014 v.3.1
SL3S1004_1014 v.3.0
SL3S1004_1014 v.1.0
• Update Automatic Pre-serialization functionality
20150727 Product data sheet
• Update UCODE 7xm+ Public Key
SL3S1004_1014 v.3.1
Modifications:
SL3S1004_1014 v.3.0
Modifications:
20150615
Product data sheet
• Update Write sensitivity
• Digital Signature explanation and source code added
• Update of final feature set
• Editorial changes
SL3S1004_1014 v.1.0
20150416
Objective data sheet
-
-
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
30 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
17. Legal information
17.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
Suitability for use — NXP Semiconductors products are not designed,
17.2 Definitions
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
17.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
31 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
17.4 Trademarks
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
UCODE — is a trademark of NXP B.V.
18. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
SL3S1004_1014
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2016. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.2 — 27 July 2016
325032
32 of 33
SL3S1004_1014
NXP Semiconductors
UCODE 7xm and UCODE 7xm+
19. Contents
1
General description. . . . . . . . . . . . . . . . . . . . . . 1
9.7.4
9.7.5
9.7.6
9.7.7
Parallel encoding . . . . . . . . . . . . . . . . . . . . . . 21
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Use cases and benefits . . . . . . . . . . . . . . . . . . 23
Tag Power Indicator . . . . . . . . . . . . . . . . . . . . 24
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Use cases and benefits . . . . . . . . . . . . . . . . . . 24
Product Status Flag (PSF) . . . . . . . . . . . . . . 25
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Use cases and benefits . . . . . . . . . . . . . . . . . . 25
Single-slit antenna solution . . . . . . . . . . . . . . 25
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Uses cases and benefits . . . . . . . . . . . . . . . . . 25
2
2.1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Key benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
End user benefit . . . . . . . . . . . . . . . . . . . . . . . . 2
Antenna design benefits . . . . . . . . . . . . . . . . . . 2
Label/module manufacturer benefit . . . . . . . . . 2
Supported features. . . . . . . . . . . . . . . . . . . . . . 2
2.1.1
2.2
2.2.1
2.2.2
2.2.3
2.3
3
3.1
3.2
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Markets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
10
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 26
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 27
UCODE 7xm/7xm+ bare die characteristics . 27
Package outline. . . . . . . . . . . . . . . . . . . . . . . . 28
Packing information . . . . . . . . . . . . . . . . . . . . 28
Wafer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 28
References. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Revision history . . . . . . . . . . . . . . . . . . . . . . . 30
4
Ordering information. . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pinning information. . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wafer layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wafer layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
11
11.1
12
5
6
6.1
7
13
13.1
14
7.1
8
8.1
8.1.1
8.1.2
8.1.3
Mechanical specification . . . . . . . . . . . . . . . . . 7
Wafer specification . . . . . . . . . . . . . . . . . . . . . . 7
Wafer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fail die identification . . . . . . . . . . . . . . . . . . . . 8
Map file distribution. . . . . . . . . . . . . . . . . . . . . . 8
15
16
17
Legal information . . . . . . . . . . . . . . . . . . . . . . 31
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 31
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 32
17.1
17.2
17.3
17.4
9
9.1
9.2
9.3
9.3.1
9.3.2
9.4
Functional description . . . . . . . . . . . . . . . . . . . 9
Air interface standards . . . . . . . . . . . . . . . . . . . 9
Power transfer . . . . . . . . . . . . . . . . . . . . . . . . . 9
Data transfer. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Interrogator to tag Link . . . . . . . . . . . . . . . . . . . 9
Tag to interrogator Link. . . . . . . . . . . . . . . . . . . 9
UCODE 7xm and UCODE 7xm+ Overview . . 10
Supported commands . . . . . . . . . . . . . . . . . . 10
Custom commands. . . . . . . . . . . . . . . . . . . . . 11
Untraceable . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ReadSignature (UCODE 7xm+ only) . . . . . . . 12
Digital Signature . . . . . . . . . . . . . . . . . . . . . . . .12
UCODE 7xm/7xm+ memory. . . . . . . . . . . . . . 15
UCODE 7xm/7xm+ overall memory map . . . . 16
UCODE 7xm/7xm+ TID memory details. . . . . 18
Supported features. . . . . . . . . . . . . . . . . . . . . 19
UCODE 7xm/7xm+ features control
18
19
Contact information . . . . . . . . . . . . . . . . . . . . 32
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.5
9.5.1
9.5.1.1
9.5.1.2
9.6
9.6.1
9.6.2
9.7
9.7.1
mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Backscatter strength reduction. . . . . . . . . . . . 20
Automatic self pre-serialization of the
9.7.2
9.7.3
96-bit EPC . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Use cases and benefits . . . . . . . . . . . . . . . . . .20
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP Semiconductors N.V. 2016.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 27 July 2016
325032
相关型号:
SL3S1013FTB0
SPECIALTY TELECOM CIRCUIT, PDSO6, 1.45 X 1 MM, 0.50 MM HEIGHT, 0.50 MM PITCH, PLASTIC, MO-252, SOT886F1, XSON-6
NXP
©2020 ICPDF网 联系我们和版权申明