SZA1010T [NXP]
Digital Servo Driver 3 DSD-3; 数字式伺服驱动器3 DSD- 3型号: | SZA1010T |
厂家: | NXP |
描述: | Digital Servo Driver 3 DSD-3 |
文件: | 总16页 (文件大小:91K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
DATA SHEET
SZA1010
Digital Servo Driver 3 (DSD-3)
1997 Apr 07
Preliminary specification
File under Integrated Circuits, IC01
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
FEATURES
GENERAL DESCRIPTION
The SZA1010 or Digital Servo Driver 3 (DSD-3) consists of
1-bit class-D power drivers, which are specially designed
for digital servo applications. Three such amplifiers are
integrated in one chip, to drive the focus and radial
actuators and the sledge motor of a compact disc optical
system.
Servo functions
• 1-bit class-D focus actuator driver (4 Ω)
• 1-bit class-D radial actuator driver (4 Ω)
• 1-bit class-D sledge motor driver (2 Ω).
Other features
The main benefits of using this principle are its higher
efficiency grade compared to conventional analog power
amplifiers, its higher integration level, its differential output
and the fact that only a few external components are
needed. When using these digital power drivers in a digital
servo application, the statement ‘complete digital servo
loop’ becomes more realistic.
• Supply voltage 5 V only
• Small package (SOT163-1)
• Higher efficiency, compared with conventional drivers,
due to the class-D principle
• Built-in digital notch filters for higher efficiency
• Enable input for focus and radial driver
• Enable input for sledge driver
• 3-state input for radial driver
• Doubled clock frequency
• Differential outputs for all drivers
• Separate power supply pins for all drivers.
QUICK REFERENCE DATA
SYMBOL
PARAMETER
MIN.
4.5
TYP.
MAX.
5.5
UNIT
VDDD
digital supply voltage
−
−
−
−
−
V
VDDA(F)
VDDA(R)
VDDA(S)
IDDDq
analog supply voltage focus actuator
analog supply voltage radial actuator
analog supply voltage sledge actuator
quiescent digital supply current
analog supply current focus actuator
analog supply current radial actuator
analog supply current sledge actuator
input clock frequency
4.5
4.5
4.5
−
5.5
5.5
5.5
10
V
V
V
µA
mA
mA
mA
MHz
mW
°C
IDDA(F)
IDDA(R)
IDDA(S)
fi(clk)
−
126
20
250
250
560
−
−
150
−
8.4672 10
Ptot
total power dissipation
−
tbf
−
Tamb
operating ambient temperature
−40
−
+85
ORDERING INFORMATION
TYPE
PACKAGE
NUMBER
NAME
DESCRIPTION
VERSION
SZA1010T
SO20
plastic small outline package; 20 leads; body width 7.5 mm
SOT163-1
1997 Apr 07
2
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
BLOCK DIAGRAM
d
V
V
V
V
DDA(R)
13
DDD
6
DDA(S)
1
DDA(F)
14
11
12
RA+
DIGITAL
NOTCH FILTER
END STAGE
H−BRIDGE
4
RAC
RA−
SZA1010
15
16
FO+
FO−
DIGITAL
NOTCH FILTER
END STAGE
H−BRIDGE
3
FOC
19
20
SL+
SL−
DIGITAL
NOTCH FILTER
END STAGE
H−BRIDGE
2
SLC
7
CLI
8
EN1
EN2
CONTROL
9
5
10
17
18
MBK013
V
/V
SSA(S) SSA(F)
3-STATE
V
V
SSA(R)
SSD
Fig.1 Block diagram.
1997 Apr 07
3
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
PINNING
SYMBOL
VDDA(S)
PIN
DESCRIPTION
analog supply voltage for sledge
motor driver
1
SLC
2
3
PDM input for sledge driver
PDM input for focus driver
PDM input for radial driver
digital ground
handbook, halfpage
V
FOC
RAC
VSSD
VDDD
CLI
1
2
20
SL−
DDA(S)
4
19 SL+
SLC
FOC
5
V
/V
3
18
17
16
SSA(S) SSA(F)
6
digital supply voltage
clock input
3-STATE
RAC
4
7
V
5
FO−
EN1
8
enable input 1
SSD
SZA1010
EN2
9
enable input 2
V
6
15 FO+
DDD
CLI
VSSA(R)
RA+
10
11
12
analog ground for radial driver
radial driver (positive output)
radial driver (negative output)
V
7
14
13
DDA(F)
DDA(R)
V
8
EN1
EN2
RA−
9
12 RA−
11
VDDA(R)
analog supply voltage for radial
driver
13
V
10
RA+
SSA(R)
MBK012
VDDA(F)
FO+
14
15
16
17
analog supply voltage for focus
focus driver (positive output)
focus driver (negative output)
radial 3-state input
FO−
3-STATE
VSSA(S)
VSSA(F)
/
analog ground for sledge
driver/focus
18
SL+
19
20
sledge driver (positive output)
sledge driver (negative output)
Fig.2 Pin configuration.
SL−
1997 Apr 07
4
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
The amplitude transfer as a function of frequency is given
in Fig.7.
FUNCTIONAL DESCRIPTION
Principle of a class-D digital power driver
Figure 7 shows that the filter has a zero on 1⁄2fs, thereby
filtering out the Idle pattern (101010). The output of this
filter is a three-level code (1.5-bit). For the control of the
switches three states (1.5-bit) can be distinguished: the
two states as described earlier and a third one. This state
is used when an idling pattern is supplied.
Figure 3 shows the block diagram of one of the digital
drivers integrated in the DSD-3. It consists of a timing
block and four CMOS switches. The input signal is a 1-bit
Pulse Density Modulated (PDM) signal, the output of the
digital servo ICs.
The maximum operating clock frequency of the device is
10 MHz. In combination with most frequently used Philips
digital servo ICs, the operating frequency of the digital
drivers is 8.4672 MHz (192 × 44.1 kHz). The sampling
frequency of the 1-bit code however is 2.1168 MHz, so
internally in the DSD-3 the clock speed of the switches will
be 2.1168 MHz.
The higher input clock frequency is used to make
non-overlapping pulses to prevent short-circuits between
the supply voltages. For the control of the switches, two
states can be distinguished. If the 1-bit code contains a
logic 1, switches A and D are closed and current will flow
in the direction as shown in Fig.4.
Switches C and D are closed (see Fig.8). In this Idle mode,
no current will flow and thus the efficiency will be improved.
This mode is also used to short-circuit the inductive
actuator/motor. In this way, high induction voltages are
prevented because the current can commutate via the
filter and the short-circuit in the switches. All three drivers
(radial, focus and sledge) contain a digital notch filter as
described (see Fig.6). Each driver has its own power
supply pins to reduce crosstalk due to of the relative high
current flowing through the pins.
Compared to the DSD-2, the DSD-3 has a 3-state mode
for the radial output, which is useful when active damping
of the radial actuator is needed. When fast access times
are required, the sledge has to move with high
accelerations. To prevent the radial actuator from moving
too far from its centre position due to the acceleration,
active damping is applied. In order to measure the
displacement of the radial actuator, the voltage induced by
the actuator itself is measured, which is proportional to its
speed. The damping consists of a sequence of controlling,
waiting, measuring and controlling etc. To be able to
measure the induced voltage properly, the influence of the
DSD-3 is eliminated by switching it into 3-state mode.
If the 1-bit code contains a logic 0, switches B and C are
closed and current will flow in the opposite direction, as
shown in Fig.5.
This indicates that the difference between the mean
number of ones and zeros in the PDM signal determines
the direction in which the actuator or motor will rotate.
If the mean number of ones and zeros is equal (Idle mode)
the current through the motor or actuator is alternated
between the positive and negative direction at a speed of
half the sample frequency of 2.1168 MHz. This results in a
high dissipation and the motor does not move.
To improve the efficiency, a digital notch filter is added at
the input of the digital drivers. This filters the Idle mode
pattern (1010101010 etc.) see Fig.6.
1997 Apr 07
5
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
V
V
DD
DD
I
pos
A
B
1-bit
code
'1'
1-bit
code
(1)
(1)
M
M
TIMING
TIMING
clock
clock
C
D
MBG786
MBG787
V
V
SS
SS
(1) Sledge motor; focus/radial motor.
(1) Sledge motor; focus/radial motor.
Fig.3 One of the digital drivers.
Fig.4 1-bit code is logic 1.
V
DD
I
neg
A
B
1-bit
code
'0'
1-bit
1.5-bit
1/Z
(1)
M
TIMING
clock
MBG789
C
D
MBG788
V
SS
The filter consists of a simple delay element (flip-flop) and an adder.
The transfer from input-to-output is: H(z) = 1 + z−1
(1) Sledge motor; focus/radial motor.
.
Fig.5 1-bit code is logic 0.
Fig.6 Notch filter at input of digital drivers.
1997 Apr 07
6
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
MBG790
V
DD
|H|
A
B
1-bit
code
'idle'
(1)
M
TIMING
clock
C
D
I
idle
MBG791
1/2f
V
s
SS
(1) Sledge motor; focus/radial motor.
Fig.7 Amplitude transfer.
Fig.8 Idling pattern.
Switches
Timing of input and output signals
The digital part of the power drivers consists of standard
cells. The power switches are specifically designed for CD
applications. The most important feature is their
on-resistance. In the applications, they have to drive very
low-ohmic actuators and/or motors. The switches are
designed to have an on-resistance of 2 Ω for the actuator
drivers and 1 Ω for the sledge motor driver. In any mode,
there are always two switches in series with the
All internal timing signals are derived from the externally
supplied CLI signal.
Sampling of the data inputs (SLC, FOC and RAC) occurs
at a frequency of 1⁄4CL. For each channel, the clocking-in
occurs at a different positive edge of CLI. Because there
are only 3 channels, and the clock frequency CLI is
divided-by-4, only 3 out of 4 positive edges are effective for
sampling one of the inputs.
actuator/motor. The total loss due to the switches is 4 Ω for
the actuators and 2 Ω for the sledge motor.
The switching of the outputs occurs in a similar way,
except that in this event the negative edge of CLI is used.
In this way, the input signals are immune to the noise
radiated by the switching of the outputs. It is possible that
an output transition will have a noticeable effect on the
power supply voltage or the ground voltage. To avoid
simultaneous transitions of all outputs, the outputs of each
bridge are also clocked at a different phase of CLI.
Consequently there are only 3 out of 4 negative edges
effective.
3-state input
When the 3-STATE input (pin 17) is made HIGH, the four
CMOS switches of the radial driver are opened.
Consequently, the radial output pins RA+ (pin 11) and RA−
(pin 12) switch into a high impedance state.
To set the circuit into 3-state mode, the clock signal (CLI)
is not required; the 3-STATE input is a direct,
asynchronous input. It has an internal pull-down resistor.
To reset the circuit, both the reset condition and the clock
should be present, because all flip-flops are reset
synchronously. The clock signal is also required to obtain
one of the possible modes of operation indicated in
Table 1.
1997 Apr 07
7
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
Table 1 Possible modes of operation
FOCUS/RADIAL
DRIVER
EN1
EN2
SLEDGE DRIVER
MODE
0
0
1
1
0
1
0
1
off
off
off
on
off
on
off
on
standby
partly operating
reset
operating
The timing diagram as shown in Fig.9 gives the relationship between the different clocks.
The negative edge of the signals called ncl0 to ncl2 is used to process the incoming data (see Table 2).
The negative edge of all signals called cl0s to cl2s is used to trigger the outputs (see Table 2).
Table 2 Signals ncl0 to ncl2 and cl0s to cl2s
SIGNAL
ncl0
DESCRIPTION
sledge input sampling clock
focus input sampling clock
radial input sampling clock
sledge output trigger clock
focus output trigger clock
radial output trigger clock
ncl1
ncl2
cl0s
cl1s
cl2s
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL PARAMETER
VDDD
VDDA(x)
SSD − VSSA(x)
MIN.
−0.5
MAX.
+6.5
UNIT
digital supply voltage
analog supply voltage
V
V
−0.5
−5
+6.5
+5
V
ground supply voltage difference
total power dissipation
mV
mW
°C
Ptot
−
tbf
Tstg
Tamb
storage temperature
−55
−40
+150
+85
operating ambient temperature
°C
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
VALUE
75
UNIT
K/W
Rth j-a
thermal resistance from junction to ambient in free air
1997 Apr 07
8
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
CHARACTERISTICS
VDDD = VDDA(x) = 5 V; VSSD = VSSA(x) = 0 V; Tamb = 25 °C; unless otherwise specified.
SYMBOL PARAMETER CONDITIONS MIN.
TYP.
MAX.
UNIT
General
VDDD
digital supply voltage
4.5
−
−
−
5.5
V
V
VDDA(x)
IDDDq
analog supply voltage
4.5
−
5.5
tbf
quiescent digital supply current
µA
IDDA(F)(max) maximum analog supply current
focus actuator
note 1
−
126
250
mA
IDDA(R)(max) maximum analog supply current
radial actuator
note 1
note 1
−
−
20
250
560
mA
mA
IDDA(S)(max) maximum analog supply current
sledge actuator
150
fi(clk)
Ptot
input clock frequency
−
8.4672
10
−
MHz
mW
°C
total power dissipation
−
tbf
Tamb
operating ambient temperature
−40
−
+85
Digital inputs; SLC, FOC, RAC, CLI, 3-STATE, EN1 and EN2
VIL
VIH
ILI
LOW level input voltage
HIGH level input voltage
input leakage current
Tamb = −40 to +85 °C
−
−
−
−
0.2VDDD
V
Tamb = −40 to +85 °C 0.8VDDD
−
V
−
1
µA
Clock input; CLI
fclk
clock frequency
−
8.4672
10
MHz
Analog outputs; FO+ and FO−
IO
output current
−
−
250
4
mA
RO
output resistance
note 2
note 2
note 2
−
tbf
Ω
Analog outputs; RA+ and RA−
IO
output current
−
−
−
250
4
mA
RO
output resistance
tbf
Ω
Analog outputs; SL+ and SL−
IO
output current
−
−
−
560
2
mA
RO
output resistance
tbf
Ω
Notes
VDDA(x)(max)
1. Maximum supply current depends on the value of RL: Imax
=
-----------------------------
(RO + RL)
2. Output resistance is defined as the series resistance of the complete bridge.
1997 Apr 07
9
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
Timing diagram
BM7G92
1997 Apr 07
10
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
APPLICATION INFORMATION
Figure 10 shows an application example.
An LC filter is connected to each output of the SZA1010 in
order to remove the PDM square wave signal at the clock
frequency. This is done to prevent the relatively long wires
to the actuators and motor from radiating and thereby
disturbing other circuitry. Therefore it is recommended to
place the coils as close as possible to the IC. The LC filter
bandwidth has been chosen as high as 20 kHz to ensure
that the filter’s poles are far enough outside the relevant
loop bandwidth, which in this application is approximately
1 kHz. In this way their influence on the closed loop
performance is kept to a minimum. Furthermore, the
corner frequency has not been chosen higher in order to
filter out noise and spurious products as much as possible,
because they enlarge the dissipation.
The various power supply and ground pins are all
connected together in the schematic, but if desired, the
focus, radial and sledge power pins can be connected to a
separate power supply.
The three ground pins are internally connected and
therefore should not be separated.
1997 Apr 07
11
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
BM0K14
a n d b o o k , f u l l p a g e w i d
1997 Apr 07
12
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
PACKAGE OUTLINE
SO20: plastic small outline package; 20 leads; body width 7.5 mm
SOT163-1
D
E
A
X
c
y
H
E
v
M
A
Z
20
11
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
10
w
detail X
e
M
b
p
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
max.
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
θ
1
2
3
p
E
p
Z
0.30
0.10
2.45
2.25
0.49
0.36
0.32
0.23
13.0
12.6
7.6
7.4
10.65
10.00
1.1
0.4
1.1
1.0
0.9
0.4
mm
2.65
0.25
0.01
1.27
0.050
1.4
0.25 0.25
0.01
0.1
8o
0o
0.012 0.096
0.004 0.089
0.019 0.013 0.51
0.014 0.009 0.49
0.30
0.29
0.42
0.39
0.043 0.043
0.016 0.039
0.035
0.016
inches 0.10
0.055
0.01 0.004
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
92-11-17
95-01-24
SOT163-1
075E04
MS-013AC
1997 Apr 07
13
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
SOLDERING
Introduction
Wave soldering
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
• The package footprint must incorporate solder thieves at
the downstream end.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Reflow soldering
Reflow soldering techniques are suitable for all SO
packages.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
1997 Apr 07
14
Philips Semiconductors
Preliminary specification
Digital Servo Driver 3 (DSD-3)
SZA1010
DEFINITIONS
Data sheet status
Objective specification
Preliminary specification
Product specification
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1997 Apr 07
15
Philips Semiconductors – a worldwide company
Argentina: see South America
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Belgium: see The Netherlands
Brazil: see South America
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Portugal: see Spain
Romania: see Italy
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Colombia: see South America
Czech Republic: see Austria
Slovakia: see Austria
Slovenia: see Italy
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 0044
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580920
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874
Indonesia: see Singapore
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Uruguay: see South America
Vietnam: see Singapore
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
Middle East: see Italy
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Internet: http://www.semiconductors.philips.com
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
© Philips Electronics N.V. 1997
SCA54
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
547027/00/01/pp16
Date of release: 1997 Apr 07
Document order number: 9397 750 01953
相关型号:
©2020 ICPDF网 联系我们和版权申明