TDA1522 [NXP]

Stereo cassette head preamplifier and equalizer; 立体声磁带磁头前置放大器和均衡器
TDA1522
型号: TDA1522
厂家: NXP    NXP
描述:

Stereo cassette head preamplifier and equalizer
立体声磁带磁头前置放大器和均衡器

放大器
文件: 总16页 (文件大小:124K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
INTEGRATED CIRCUITS  
DATA SHEET  
TDA1522  
Stereo cassette head  
preamplifier and equalizer  
1996 Feb 26  
Product specification  
File under Integrated Circuits, IC01  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
FEATURES  
GENERAL DESCRIPTION  
Two independent amplifiers with open-loop gain of  
90 dB (typical)  
The TDA1522 is a playback amplifier for car radio/cassette  
players.  
Internal DC feedback via 140 kresistor from output to  
feedback point  
AC characteristics that can be determined externally by  
an RC network  
Electronic on/off switching with transient suppression for  
switch on  
Head input at DC ground that eliminates the input  
coupling capacitor  
Minimum external component requirement  
Stability down to a gain of 30 dB  
Low input noise  
Low distortion  
DC input current <2 µA  
Wide supply voltage range.  
QUICK REFERENCE DATA  
SYMBOL  
PARAMETER  
CONDITIONS  
MIN.  
7.5  
TYP.  
MAX.  
23  
UNIT  
VP  
IP  
supply voltage (pin 8)  
supply current (pin 8)  
operating ambient temperature  
total harmonic distortion  
channel separation  
5
V
mA  
°C  
%
Tamb  
THD  
αcs  
30  
+85  
0.05  
RS = 10 k; LS = 0  
45  
dB  
ORDERING INFORMATION  
TYPE  
PACKAGE  
NUMBER  
NAME  
DESCRIPTION  
VERSION  
TDA1522  
SIL9MP  
plastic single in-line medium power package; 9 leads  
SOT142-1  
1996 Feb 26  
2
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
BLOCK DIAGRAM  
C101  
22 nF  
R102  
R101  
C102  
220  
µF  
8.2 Ω  
5.6 kΩ  
TDA1522  
feedback 1  
140 kΩ  
R
fb1  
C
3
4
c1  
output 1  
1
5
V
AMP 1  
o1  
10 µF  
R
L1  
4.7 kΩ  
R
L
= 300 Ω  
S1  
S1  
V
V
i1  
i2  
= 80 mH  
SUPPLY  
&
MUTE  
2
MUTE  
R
L
= 300 Ω  
= 80 mH  
S2  
S2  
8
9
C
6
7
c2  
output 2  
V
AMP 2  
o2  
10 µF  
R
L2  
4.7 kΩ  
R
fb2  
140 kΩ  
feedback 2  
R201  
C201  
22 nF  
R202  
C202  
220  
µF  
8.2 Ω  
5.6 kΩ  
V
P
MLD337  
Fig.1 Block diagram with external components; also used as test circuit.  
1996 Feb 26  
3
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
PINNING  
SYMBOL  
Vo1  
PIN  
DESCRIPTION  
output voltage 1  
1
2
3
4
5
6
7
8
9
handbook, halfpage  
V
1
2
3
4
5
6
7
8
9
o1  
MUTE  
FB1  
Vi1  
mute input  
MUTE  
FB1  
feedback 1  
input voltage 1  
ground  
GND  
Vi2  
V
i1  
input voltage 2  
feedback 2  
GND  
TDA1522  
FB2  
VP  
V
i2  
power supply  
output voltage 2  
FB2  
Vo2  
V
P
V
o2  
MGC396  
Fig.2 Pin configuration.  
1996 Feb 26  
4
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
LIMITING VALUES  
In accordance with the Absolute Maximum Rating System (IEC 134); note 1.  
SYMBOL  
PARAMETER  
MIN.  
7.5  
MAX.  
23  
UNIT  
VP  
Ifb  
supply voltage (pin 8)  
V
feedback current (pins 3 and 7)  
total power dissipation  
10  
mA  
mW  
°C  
Ptot  
800  
+85  
+150  
Tamb  
Tstg  
operating ambient temperature  
storage temperature  
30  
55  
°C  
Note  
1. All pins except 3 and 7 (feedback) can be connected to VP (pin 8) or ground (pin 5).  
CHARACTERISTICS  
VP = 8.5 V; Tamb = 25 °C; see test circuit Fig.1; unless otherwise specified.  
SYMBOL  
PARAMETER  
CONDITIONS  
MIN.  
TYP. MAX. UNIT  
Supply (pin 8)  
VP  
IP  
supply voltage  
supply current  
7.5  
23  
V
5
mA  
Inputs (pins 4 or 6)  
Vni(rms) unweighted noise input voltage  
f = 20 Hz to 20 kHz;  
measured in Fig.3  
1.6  
5
µV  
(RMS value)  
Vni  
noise input voltage  
RS = 0; f = 1 kHz; measured  
in Fig.3; see also Fig.5  
nV  
-----------  
Hz  
Ini  
noise input current  
f = 1 kHz; measured in Fig.3;  
see also Fig.6  
1.2  
pA  
-----------  
Hz  
I4, I6  
Zi  
DC input current at pins 4 and 6  
input impedance  
2  
µA  
kΩ  
f = 1 kHz; note 1  
200  
Outputs (pins 1 or 9); see Fig.7  
Vo  
output voltage  
Vi = 0.3 mV; f = 315 Hz  
THD = 1%; f = 1 kHz  
0.72  
V
1.0  
5  
V
IO  
output source current  
DC output voltage  
V2-5 7.5 V; mute off  
10  
3.7  
700  
mA  
V
VO  
Vno(rms)  
weighted noise output voltage;  
DIN A (RMS value)  
RS = 300 ; LS = 80 mH  
µV  
Vno  
weighted noise output voltage  
CCITT (peak value)  
RS = 300 ; LS = 80 mH  
RS = 300 ; LS = 80 mH  
RS = 300 ; LS = 80 mH  
1200  
1600  
1800  
µV  
µV  
µV  
CCIR (peak value)  
Vno  
Zo  
unweighted noise output voltage;  
DIN 45405 (peak value)  
output impedance  
f = 1 kHz; note 1  
1
kΩ  
1996 Feb 26  
5
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
SYMBOL  
PARAMETER  
CONDITIONS  
MIN.  
TYP. MAX. UNIT  
Mute on/off (pin 2); see Fig.4  
Vmute(on)  
Imute(on)  
mute on voltage  
mute on current  
mute switch closed  
0
1
V
mute switch closed or  
V2-5 = 0 V  
2.7  
µA  
Vmute(off)  
mute off voltage  
mute switch open  
7.5  
VP  
V
General  
Rfb  
internal feedback resistor  
open-loop voltage gain  
channel separation  
note 1  
100  
140  
90  
180  
kΩ  
dB  
dB  
dB  
Gv  
f = 315 Hz; note 1  
RS = 10 k; LS = 0; note 2  
αcs  
45  
90  
PSRR  
power supply ripple rejection  
VP(rms) = 0.1 V; f = 100 Hz;  
95  
note 3  
THD  
total harmonic distortion  
f = 1 kHz; Vo = 0.3 V; note 4  
0.05  
%
Notes  
1. Applies to each amplifier.  
2. Frequency range 300 Hz to 20 kHz.  
3. Referred to the input.  
4. Measured selective.  
C101  
R102  
R101  
C102  
8.2 Ω  
9.1 kΩ  
10 µF  
1000  
µF  
TDA1522  
feedback 1  
140 kΩ  
R
fb1  
C
3
4
c1  
output 1  
1
5
V
AMP 1  
o1  
V
i1  
10 µF  
R
L1  
4.7 kΩ  
R
S1  
4.7 kΩ  
SUPPLY  
&
2
MUTE  
R
S2  
4.7 kΩ  
8
9
C
6
7
c2  
V
output 2  
i2  
V
AMP 2  
o2  
10 µF  
R
L2  
4.7 kΩ  
R
fb2  
140 kΩ  
feedback 2  
R201  
C201  
R202  
8.2 Ω  
C202  
1000  
µF  
9.1 kΩ  
10 µF  
V
P
MLD338  
Fig.3 Test circuit for noise measurement.  
6
1996 Feb 26  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
MLD339  
0
handbook, halfpage  
V
o
(dB)  
20  
40  
60  
80  
100  
0
2
4
6
V
(V)  
5
2
Fig.4 Muting depth as a function of control voltage  
at pin 2.  
MLD340  
2
10  
V
ni  
(nV/ Hz)  
(1)  
(2)  
10  
(3)  
1
2
3
4
5
10  
10  
10  
10  
10  
f
(Hz)  
(1) RS = 10 k.  
(2) RS = 5 k.  
(3) RS = 0.  
Fig.5 Noise input voltage as a function of frequency.  
7
1996 Feb 26  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
MLD341  
10  
I
ni  
(pA/ Hz)  
1
1
10  
2
3
4
5
10  
10  
10  
10  
10  
f (Hz)  
Fig.6 Noise input current as a function of frequency.  
MLD342  
20  
g
f
315 Hz  
g
(dB)  
10  
0
10  
20  
30  
10  
2
3
4
5
10  
10  
10  
10  
f (Hz)  
Fig.7 Frequency response curve for the circuit in Fig.1.  
8
1996 Feb 26  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
PRINTED-CIRCUIT BOARD  
58  
R201  
RM1  
D201  
C201  
R202  
C
C2  
R
V
L2  
o2  
V
i2  
V
P
RS2  
C202  
C102  
SM  
45  
CVP1  
IC1  
RS1  
MUTE  
V
i1  
CM  
R
V
L1  
C101  
D101  
o1  
C
C1  
R102  
R101  
RM  
MGC995  
Fig.8 Printed-circuit board component side, showing component layout of Fig.1 and/or Fig.10.  
1996 Feb 26  
9
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
APPLICATION INFORMATION  
C101  
22 nF  
R102  
R101  
C102  
8.2 Ω  
5.6 kΩ  
220  
µF  
TDA1522  
feedback 1  
140 kΩ  
R
fb1  
C
3
4
c1  
output 1  
1
5
V
AMP 1  
o1  
10 µF  
R
L1  
4.7 kΩ  
R
L
= 300 Ω  
S1  
S1  
V
V
i1  
i2  
= 80 mH  
SUPPLY  
&
MUTE  
2
R
L
= 300 Ω  
S2  
S2  
8
9
= 80 mH  
C
6
7
c2  
output 2  
R
m
V
o2  
AMP 2  
10 µF  
R
150 kΩ  
1 µF  
L2  
4.7 kΩ  
R
MUTE  
SWITCH  
fb2  
140 kΩ  
feedback 2  
R201  
C201  
22 nF  
R202  
8.2 Ω  
C202  
220  
5.6 kΩ  
V
P
MLD343  
µF  
Fig.9 Simple mute application.  
1996 Feb 26  
10  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
1N4148  
C101  
22 nF  
R102  
R101  
5.6 kΩ  
C102  
220  
µF  
8.2 Ω  
TDA1522  
feedback 1  
140 kΩ  
R
fb1  
C
3
4
c1  
output 1  
1
5
V
AMP 1  
o1  
10 µF  
R
L1  
4.7 kΩ  
R
L
= 300 Ω  
S1  
S1  
V
V
i1  
i2  
= 80 mH  
SUPPLY  
&
MUTE  
2
R
L
= 300 Ω  
S2  
S2  
8
9
= 80 mH  
C
6
7
c2  
output 2  
V
AMP 2  
o2  
10 µF  
R
68 kΩ  
L2  
4.7 kΩ  
R
MUTE  
SWITCH  
fb2  
68  
2.2  
kΩ  
µF  
140 kΩ  
feedback 2  
R201  
C201  
22 nF  
R202  
8.2 Ω  
5.6 kΩ  
C202  
220 µF  
1N4148  
V
MLD344  
P
Fig.10 Application for plop-free muting.  
1996 Feb 26  
11  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
PACKAGE OUTLINE  
SIL9MP:plastic single in-line medium power package; 9 leads  
SOT142-1  
D
A
2
D
1
A
3
E
A
pin 1 index  
c
L
1
9
b
Q
e
Z
b
w
M
2
b
1
0
5
10 mm  
scale  
DIMENSIONS (mm are the original dimensions)  
(1)  
A
2
max.  
Z
(1)  
(1)  
UNIT  
A
A
b
b
b
c
D
D
1
E
e
L
Q
w
3
1
2
max.  
12  
11  
1.8  
1.4  
1.40  
1.14  
0.67  
0.50  
1.40 0.48 21.8 21.4  
1.14 0.38 21.4 20.7  
6.48  
6.20  
3.9  
3.4  
1.75  
1.55  
2.54  
mm  
3.7  
0.25  
1.0  
Note  
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.  
REFERENCES  
OUTLINE  
EUROPEAN  
PROJECTION  
ISSUE DATE  
VERSION  
IEC  
JEDEC  
EIAJ  
92-11-17  
95-02-09  
SOT142-1  
1996 Feb 26  
12  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
The device may be mounted up to the seating plane, but  
the temperature of the plastic body must not exceed the  
specified maximum storage temperature (Tstg max). If the  
printed-circuit board has been pre-heated, forced cooling  
may be necessary immediately after soldering to keep the  
temperature within the permissible limit.  
SOLDERING  
Introduction  
There is no soldering method that is ideal for all IC  
packages. Wave soldering is often preferred when  
through-hole and surface mounted components are mixed  
on one printed-circuit board. However, wave soldering is  
not always suitable for surface mounted ICs, or for  
printed-circuits with high population densities. In these  
situations reflow soldering is often used.  
Repairing soldered joints  
Apply a low voltage soldering iron (less than 24 V) to the  
lead(s) of the package, below the seating plane or not  
more than 2 mm above it. If the temperature of the  
soldering iron bit is less than 300 °C it may remain in  
contact for up to 10 seconds. If the bit temperature is  
between 300 and 400 °C, contact may be up to 5 seconds.  
This text gives a very brief insight to a complex technology.  
A more in-depth account of soldering ICs can be found in  
our “IC Package Databook” (order code 9398 652 90011).  
Soldering by dipping or by wave  
The maximum permissible temperature of the solder is  
260 °C; solder at this temperature must not be in contact  
with the joint for more than 5 seconds. The total contact  
time of successive solder waves must not exceed  
5 seconds.  
DEFINITIONS  
Data sheet status  
Objective specification  
Preliminary specification  
Product specification  
This data sheet contains target or goal specifications for product development.  
This data sheet contains preliminary data; supplementary data may be published later.  
This data sheet contains final product specifications.  
Limiting values  
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or  
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation  
of the device at these or at any other conditions above those given in the Characteristics sections of the specification  
is not implied. Exposure to limiting values for extended periods may affect device reliability.  
Application information  
Where application information is given, it is advisory and does not form part of the specification.  
LIFE SUPPORT APPLICATIONS  
These products are not designed for use in life support appliances, devices, or systems where malfunction of these  
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for  
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such  
improper use or sale.  
1996 Feb 26  
13  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
NOTES  
1996 Feb 26  
14  
Philips Semiconductors  
Product specification  
Stereo cassette head  
preamplifier and equalizer  
TDA1522  
NOTES  
1996 Feb 26  
15  
Philips Semiconductors – a worldwide company  
Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428)  
BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367  
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,  
Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc.,  
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,  
Metro MANILA, Tel. (63) 2 816 6380, Fax. (63) 2 817 3474  
Tel. (02)805 4455, Fax. (02)805 4466  
Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213,  
Tel. (01)60 101-1236, Fax. (01)60 101-1211  
Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands,  
Portugal: PHILIPS PORTUGUESA, S.A.,  
Rua dr. António Loureiro Borges 5, Arquiparque - Miraflores,  
Apartado 300, 2795 LINDA-A-VELHA,  
Tel. (01)4163160/4163333, Fax. (01)4163174/4163366  
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,  
Tel. (65)350 2000, Fax. (65)251 6500  
South Africa: S.A. PHILIPS Pty Ltd.,  
Tel. (31)40-2783749, Fax. (31)40-2788399  
Brazil: Rua do Rocio 220 - 5th floor, Suite 51,  
CEP: 04552-903-SÃO PAULO-SP, Brazil,  
P.O. Box 7383 (01064-970),  
195-215 Main Road Martindale, 2092 JOHANNESBURG,  
P.O. Box 7430, Johannesburg 2000,  
Tel. (011)470-5911, Fax. (011)470-5494  
Tel. (011)821-2333, Fax. (011)829-1849  
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS:  
Tel. (800) 234-7381, Fax. (708) 296-8556  
Chile: Av. Santa Maria 0760, SANTIAGO,  
Spain: Balmes 22, 08007 BARCELONA,  
Tel. (03)301 6312, Fax. (03)301 42 43  
Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM,  
Tel. (0)8-632 2000, Fax. (0)8-632 2745  
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,  
Tel. (02)773 816, Fax. (02)777 6730  
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,  
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,  
Tel. (852)2319 7888, Fax. (852)2319 7700  
Tel. (01)488 2211, Fax. (01)481 77 30  
Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West  
Road, Sec. 1. Taipeh, Taiwan ROC, P.O. Box 22978,  
TAIPEI 100, Tel. (886) 2 382 4443, Fax. (886) 2 382 4444  
Colombia: IPRELENSO LTDA, Carrera 21 No. 56-17,  
77621 BOGOTA, Tel. (571)249 7624/(571)217 4609,  
Fax. (571)217 4549  
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,  
209/2 Sanpavuth-Bangna Road Prakanong,  
Bangkok 10260, THAILAND,  
Tel. (66) 2 745-4090, Fax. (66) 2 398-0793  
Turkey:Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,  
Tel. (0212)279 27 70, Fax. (0212)282 67 07  
Ukraine: Philips UKRAINE, 2A Akademika Koroleva str., Office 165,  
Denmark: Prags Boulevard 80, PB 1919, DK-2300  
COPENHAGEN S, Tel. (45)32 88 26 36, Fax. (45)31 57 19 49  
Finland: Sinikalliontie 3, FIN-02630 ESPOO,  
Tel. (358)0-615 800, Fax. (358)0-61580 920  
France: 4 Rue du Port-aux-Vins, BP317,  
92156 SURESNES Cedex,  
Tel. (01)4099 6161, Fax. (01)4099 6427  
Germany: P.O. Box 10 51 40, 20035 HAMBURG,  
252148 KIEV, Tel. 380-44-4760297, Fax. 380-44-4766991  
United Kingdom: Philips Semiconductors LTD.,  
276 Bath Road, Hayes, MIDDLESEX UB3 5BX,  
Tel. (0181)730-5000, Fax. (0181)754-8421  
United States:811 East Arques Avenue, SUNNYVALE,  
CA 94088-3409, Tel. (800)234-7381, Fax. (708)296-8556  
Uruguay: Coronel Mora 433, MONTEVIDEO,  
Tel. (040)23 53 60, Fax. (040)23 53 63 00  
Greece: No. 15, 25th March Street, GR 17778 TAVROS,  
Tel. (01)4894 339/4894 911, Fax. (01)4814 240  
India: Philips INDIA Ltd, Shivsagar Estate, A Block,  
Dr. Annie Besant Rd. Worli, Bombay 400 018  
Tel. (022)4938 541, Fax. (022)4938 722  
Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4,  
P.O. Box 4252, JAKARTA 12950,  
Tel. (02)70-4044, Fax. (02)92 0601  
Tel. (021)5201 122, Fax. (021)5205 189  
Ireland: Newstead, Clonskeagh, DUBLIN 14,  
Tel. (01)7640 000, Fax. (01)7640 200  
Italy: PHILIPS SEMICONDUCTORS S.r.l.,  
Piazza IV Novembre 3, 20124 MILANO,  
Tel. (0039)2 6752 2531, Fax. (0039)2 6752 2557  
Japan: Philips Bldg 13-37, Kohnan2-chome, Minato-ku, TOKYO 108,  
Tel. (03)3740 5130, Fax. (03)3740 5077  
Korea: Philips House, 260-199 Itaewon-dong,  
Internet: http://www.semiconductors.philips.com/ps/  
For all other countries apply to: Philips Semiconductors,  
International Marketing and Sales, Building BE-p,  
P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands,  
Telex 35000 phtcnl, Fax. +31-40-2724825  
Yongsan-ku, SEOUL, Tel. (02)709-1412, Fax. (02)709-1415  
SCDS47  
© Philips Electronics N.V. 1996  
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,  
SELANGOR, Tel. (03)750 5214, Fax. (03)757 4880  
Mexico: 5900 Gateway East, Suite 200, EL PASO, TX 79905,  
Tel. 9-5(800)234-7381, Fax. (708)296-8556  
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,  
Tel. (040)2783749, Fax. (040)2788399  
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,  
All rights are reserved. Reproduction in whole or in part is prohibited without the  
prior written consent of the copyright owner.  
The information presented in this document does not form part of any quotation  
or contract, is believed to be accurate and reliable and may be changed without  
notice. No liability will be accepted by the publisher for any consequence of its  
use. Publication thereof does not convey nor imply any license under patent- or  
other industrial or intellectual property rights.  
Tel. (09)849-4160, Fax. (09)849-7811  
Norway: Box 1, Manglerud 0612, OSLO,  
Printed in The Netherlands  
Tel. (022)74 8000, Fax. (022)74 8341  
Pakistan: Philips Electrical Industries of Pakistan Ltd.,  
Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton,  
KARACHI 75600, Tel. (021)587 4641-49,  
Fax. (021)577035/5874546  
517021/1100/01/pp16  
Date of release: 1996 Feb 26  
9397 750 00693  
Document order number:  

相关型号:

TDA1523

Stereo cassette head preamplifier and equalizer

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NXP

TDA1524

Stereo-tone/volume control circuit

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NXP

TDA1524A

Stereo-tone/volume control circuit

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NXP

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NXP

TDA1525

双音量/音调直流控制电路

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC

TDA1526

Stereo-tone/volume control circuit

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NXP

TDA1526N

暂无描述

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NXP

TDA1535B

HIGH-SPEED SINGLE SAMPLE-AND-HOLD AMPLIFIER

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NXP

TDA1540

14-Bit DAC (Serial Output)

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC

TDA1540D

14-Bit DAC (Serial Output)

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC

TDA1540PN

14-Bit DAC (Serial Output)

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC

TDA1540TD

14-Bit DAC (Serial Output)

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC