UJA1075TW/5V0,118 [NXP]
UJA1075TW;型号: | UJA1075TW/5V0,118 |
厂家: | NXP |
描述: | UJA1075TW |
文件: | 总53页 (文件大小:348K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UJA1075
High-speed CAN/LIN core system basis chip
Rev. 02 — 27 May 2010
Product data sheet
1. General description
The UJA1075 core System Basis Chip (SBC) replaces the basic discrete components
commonly found in Electronic Control Units (ECU) with a high-speed Controller Area
Network (CAN) and a Local Interconnect Network (LIN) interface.
The UJA1075 supports the networking applications used to control power and sensor
peripherals by using a high-speed CAN as the main network interface and the LIN
interface as a local sub-bus.
The core SBC contains the following integrated devices:
• High-speed CAN transceiver, inter-operable and downward compatible with CAN
transceiver TJA1042, and compatible with the ISO 11898-2 and ISO 11898-5
standards
• LIN transceiver compliant with LIN 2.1, LIN 2.0 and SAE J2602, and compatible with
LIN 1.3
• Advanced independent watchdog (UJA1075/xx/WD versions)
• 250 mA voltage regulator for supplying a microcontroller; extendable with external
PNP transistor for increased current capability and dissipation distribution
• Separate voltage regulator for supplying the on-board CAN transceiver
• Serial Peripheral Interface (SPI) (full duplex)
• 2 local wake-up input ports
• Limp home output port
In addition to the advantages gained from integrating these common ECU functions in a
single package, the core SBC offers an intelligent combination of system-specific
functions such as:
• Advanced low-power concept
• Safe and controlled system start-up behavior
• Detailed status reporting on system and sub-system levels
The UJA1075 is designed to be used in combination with a microcontroller that
incorporates a CAN controller. The SBC ensures that the microcontroller always starts up
in a controlled manner.
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
2. Features and benefits
2.1 General
Contains a full set of CAN and LIN ECU functions:
CAN transceiver and LIN transceiver
Scalable 3.3 V or 5 V voltage regulator delivering up to 250 mA for a
microcontroller and peripheral circuitry; an external PNP transistor can be
connected for better heat distribution over the PCB
Separate voltage regulator for the CAN transceiver (5 V)
Watchdog with Window and Timeout modes and on-chip oscillator
Serial Peripheral Interface (SPI) for communicating with the microcontroller
ECU power management system
Designed for automotive applications:
Excellent ElectroMagnetic Compatibility (EMC) performance
±8 kV ElectroStatic Discharge (ESD) protection Human Body Model (HBM) on the
CAN/LIN bus pins and the wake pins
±6 kV ElectroStatic Discharge (ESD) protection IEC 61000-4-2 on the CAN/LIN bus
pins and the wake pins
±58 V short-circuit proof CAN/LIN bus pins
Battery and CAN/LIN bus pins are protected against transients in accordance with
ISO 7637-3
Supports remote flash programming via the CAN bus
Small 6.1 mm × 11 mm HTSSOP32 package with low thermal resistance
Pb-free; RoHS and dark green compliant
2.2 CAN transceiver
ISO 11898-2 and ISO 11898-5 compliant high-speed CAN transceiver
Dedicated low dropout voltage regulator for the CAN bus:
Independent of the microcontroller supply
Significantly improves EMC performance
Bus connections are truly floating when power is off
SPLIT output pin for stabilizing the recessive bus level
2.3 LIN transceiver
LIN 2.1 compliant LIN transceiver
Compliant with SAE J2602
Downward compatible with LIN 2.0 and LIN 1.3
Low slope mode for optimized EMC performance
Integrated LIN termination diode at pin DLIN
2.4 Power management
Wake-up via CAN, LIN or local wake pins with wake-up source detection
2 Wake pins:
WAKE1 and WAKE2 inputs can be switched off to reduce current flow
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
2 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Output signal (WBIAS) to bias the wake pins, selectable sampling time of 16 ms or
64 ms
Standby mode with very low standby current and full wake-up capability; V1 active to
maintain supply to the microcontroller
Sleep mode with very low sleep current and full wake-up capability
2.5 Control and Diagnostic features
Safe and predictable behavior under all conditions
Programmable watchdog with independent clock source:
Window, Timeout (with optional cyclic wake-up) and Off modes supported (with
automatic re-enable in the event of an interrupt)
16-bit Serial Peripheral Interface (SPI) for configuration, control and diagnosis
Global enable output for controlling safety-critical hardware
Limp home output (LIMP) for activating application-specific ‘limp home’ hardware in
the event of a serious system malfunction
Overtemperature shutdown
Interrupt output pin; interrupts can be individually configured to signal V1/V2
undervoltage, CAN/LIN/local wake-up and cyclic and power-on interrupt events
Bidirectional reset pin with variable power-on reset length to support a variety of
microcontrollers
Software-initiated system reset
2.6 Voltage regulators
Main voltage regulator V1:
Scalable voltage regulator for the microcontroller, its peripherals and additional
external transceivers
±2 % accuracy for LIN master application
±3 % accuracy for LIN slave application
3.3 V and 5 V versions available
Delivers up to 250 mA and can be combined with an external PNP transistor for
better heat distribution over the PCB
Selectable current threshold at which the external PNP transistor starts to deliver
current
Undervoltage warning at 90 % of nominal output voltage and undervoltage reset at
90 % or 70 % of nominal output voltage
Can operate at VBAT voltages down to 4.5 V (e.g. during cranking), in accordance
with ISO7637 pulse 4/4b and ISO16750-2
Stable output under all conditions
Voltage regulator V2 for CAN transceiver:
Dedicated voltage regulator for on-chip high-speed CAN transceiver
Undervoltage warning at 90 % of nominal output voltage
Can be switched off; CAN transceiver can be supplied by V1 or by an external
voltage regulator
Can operate at VBAT voltages down to 5.5 V (e.g. during cranking) in accordance
with ISO7637, pulse 4
Stable output under all conditions
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
3 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
3. Ordering information
Table 1.
Ordering information
Type number[1]
Package
Name
Description
Version
UJA1075TW/5V0/WD
UJA1075TW/3V3/WD
UJA1075TW/5V0
HTSSOP32
plastic thermal enhanced thin shrink small outline package;
32 leads; body width 6.1 mm; lead pitch 0.65 mm; exposed die
pad
SOT549-1
UJA1075TW/3V3
[1] UJA1075TW/5V0xx versions contain a 5 V regulator (V1); UJA1075TW/3V3xx versions contain a 3.3 V regulator (V1); WD versions
contain a watchdog.
4. Block diagram
UJA1075
V1
V1
V2
BAT
V2
GND
V1
V2
UV
UV
VEXCTRL
VEXCC
EXT. PNP
CTRL
SCK
SDI
WBIAS
SDO
SCSN
WAKE1
WAKE2
WDOFF
EN
SYSTEM
CONTROLLER
INTN
RSTN
WAKE
OSC
TEMP
BAT
LIMP
DLIN
V2
LIN
TXDL
RXDL
HS-CAN
LIN
CANH
CANL
TXDC
RXDC
SPLIT
BAT
015aaa118
Fig 1. Block diagram
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
4 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
5. Pinning information
5.1 Pinning
1
2
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
i.c.
i.c.
BAT
VEXCTRL
TEST2
VEXCC
WBIAS
i.c.
3
TXDL
V1
4
5
RXDL
RSTN
INTN
EN
6
7
DLIN
8
LIN
UJA1075
9
SDI
SPLIT
GND
10
11
12
13
14
15
16
SDO
SCK
CANL
CANH
V2
SCSN
TXDC
RXDC
TEST1
WDOFF
WAKE2
WAKE1
LIMP
015aaa119
Fig 2. Pin configuration
5.2 Pin description
Table 2.
Symbol
i.c.
Pin description
Pin
1
Description
internally connected; should be left floating
internally connected; should be left floating
LIN transmit data input
i.c.
2
TXDL
V1
3
4
voltage regulator output for the microcontroller (5 V or 3.3 V depending on
SBC version)
RXDL
RSTN
INTN
EN
5
LIN receive data output
6
reset input/output to and from the microcontroller
interrupt output to the microcontroller
enable output
7
8
SDI
9
SPI data input
SDO
10
11
12
13
14
15
16
17
SPI data output
SCK
SPI clock input
SCSN
TXDC
RXDC
TEST1
WDOFF
LIMP
SPI chip select input
CAN transmit data input
CAN receive data output
test pin; pin should be connected to ground
WDOFF pin for deactivating the watchdog
limp home output
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
5 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 2.
Pin description …continued
Symbol
WAKE1
WAKE2
V2
Pin
18
19
20
21
22
23
24
25
26
27
28
29
Description
local wake-up input 1
local wake-up input 2
5 V voltage regulator output for CAN
CANH bus line
CANH
CANL
GND
CANL bus line
ground
SPLIT
LIN
CAN bus common mode stabilization output
LIN bus line
DLIN
LIN termination resistor connection
internally connected; should be left floating
control pin for external wake biasing transistor
i.c.
WBIAS
VEXCC
current measurement for external PNP transistor; this pin is connected to
the collector of the external PNP transistor
TEST2
30
31
test pin; pin should be connected to ground
VEXCTRL
control pin of the external PNP transistor; this pin is connected to the base
of the external PNP transistor
BAT
32
battery supply for the SBC
The exposed die pad at the bottom of the package allows for better heat dissipation from
the SBC via the printed circuit board. The exposed die pad is not connected to any active
part of the IC and can be left floating, or can be connected to GND.
6. Functional description
The UJA1075 combines the functionality of a high-speed CAN transceiver, a LIN
transceiver, two voltage regulators and a watchdog (UJA1075/xx/WD versions) in a
single, dedicated chip. It handles the power-up and power-down functionality of the ECU
and ensures advanced system reliability. The SBC offers wake-up by bus activity, by
cyclic wake-up and by the activation of external switches. Additionally, it provides a
periodic control signal for pulsed testing of wake-up switches, allowing low-current
operation even when the wake-up switches are closed in Standby mode.
All transceivers are optimized to be highly flexible with regard to bus topologies. In
particular, the high-speed CAN transceiver is optimized to reduce ringing (bus reflections).
V1, the main voltage regulator, is designed to power the ECU's microcontroller, its
peripherals and additional external transceivers. An external PNP transistor can be added
to improve heat distribution. V2 supplies the integrated high-speed CAN transceiver. The
watchdog is clocked directly by the on-chip oscillator and can be operated in Window,
Timeout and Off modes.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
6 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.1 System Controller
6.1.1 Introduction
The system controller manages register configuration and controls the internal functions
of the SBC. Detailed device status information is collected and presented to the
microcontroller. The system controller also provides the reset and interrupt signals.
The system controller is a state machine. The SBC operating modes, and how transitions
between modes are triggered, are illustrated in Figure 3. These modes are discussed in
more detail in the following sections.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
7 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
from Standby or Normal
chip temperature above
OTP activatrion threshold T
th(act)otp
Overtemp
V
BAT
below
V1: OFF
V2: OFF
power-off threshold V
th(det)poff
(from all modes)
limp home = LOW (active)
CAN/LIN: Off and
high resistance
watchdog: OFF
Off
chip temperature below
OTP release threshold T
V1: OFF
V2: OFF
th(rel)otp
CAN/LIN: Off and
high resistance
watchdog: OFF
INTN: HIGH
V
below
BAT
power-on threshold V
th(det)pon
V
BAT
above
power-on threshold V
th(det)pon
watchdog
trigger
watchdog overflow or
V1 undervoltage
Standby
V1: ON
V2: OFF
CAN/LIN: Lowpower/Off
watchdog: Timeout/Off
MC = 00
MC = 01 and
INTN = HIGH and
one wake-up enabled and
no wake-up pending
reset event or
MC = 00
MC = 10 or MC = 11
wake-up event if enabled
Sleep
Normal
V1: OFF
V2: OFF
CAN/LIN: Lowpower/Off
watchdog: OFF
RSTN: LOW
V1: ON
V2: ON/OFF
CAN/LIN: Active/Lowpower
watchdog: Window/
Timeout/Off
successful
watchdog
trigger
MC = 01 and
INTN = HIGH and
one wake-up enabled and
no wake-up pending
MC = 01
MC = 1x
015aaa073
Fig 3. UJA1075 system controller
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
8 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.1.2 Off mode
The SBC switches to Off mode from all other modes if the battery supply drops below the
power-off detection threshold (Vth(det)poff). In Off mode, the voltage regulators are disabled
and the bus systems are in a high-resistive state. The CAN bus pins are floating in this
mode.
As soon as the battery supply rises above the power-on detection threshold (Vth(det)pon),
the SBC goes to Standby mode, and a system reset is executed (reset pulse width of
tw(rst), long or short; see Section 6.5.1 and Table 11).
6.1.3 Standby mode
The SBC will enter Standby mode:
• From Off mode if VBAT rises above the power-on detection threshold (Vth(det)pon
)
• From Sleep mode on the occurrence of a CAN, LIN or local wake-up event
• From Overtemp mode if the chip temperature drops below the overtemperature
protection release threshold, Tth(rel)otp
• From Normal mode if bit MC is set to 00 or a system reset is performed (see
Section 6.5)
In Standby mode, V1 is switched on. The CAN and LIN transceivers will either be in a
low-power state (Lowpower mode; STBCC/STBCL = 1; see Table 6) with bus wake-up
detection enabled or completely switched off (Off mode; STBCC/STBCL = 0) - see
Section 6.7.1 and Section 6.8.1. The watchdog can be running in Timeout mode or Off
mode, depending on the state of the WDOFF pin and the setting of the watchdog mode
control bit (WMC) in the WD_and_Status register (Table 4).
The SBC will exit Standby mode if:
• Normal mode is selected by setting bits MC to 10 (V2 disabled) or 11 (V2 enabled)
• Sleep mode is selected by setting bits MC to 01
• The chip temperature rises above the OTP activation threshold, Tth(act)otp, causing the
SBC to enter Overtemp mode
6.1.4 Normal mode
Normal mode is selected from Standby mode by setting bits MC in the Mode_Control
register (Table 5) to 10 (V2 disabled) or 11 (V2 enabled).
In Normal mode, the CAN physical layer will be enabled (Active mode; STBCC = 0; see
Table 6) or in a low-power state (Lowpower mode; STBCC = 1) with bus wake-up
detection active.
In Normal mode, the LIN physical layer will be enabled (Active mode; STBCL = 0; see
Table 6) or in a low-power state (Lowpower mode; STBCL = 1) with bus wake-up
detection active.
The SBC will exit Normal mode if:
• Standby mode is selected by setting bits MC to 00
• Sleep mode is selected by setting bits MC to 01
• A system reset is generated (see Section 6.1.3; the SBC will enter Standby mode)
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
9 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
• The chip temperature rises above the OTP activation threshold, Tth(act)otp, causing the
SBC to switch to Overtemp mode
6.1.5 Sleep mode
Sleep mode is selected from Standby mode or Normal mode by setting bits MC in the
Mode_Control register (Table 5) to 01. The SBC will enter Sleep mode providing there are
no pending interrupts (INTN = HIGH) or wake-up events and at least one wake-up source
is enabled (CAN, LIN or WAKE). Any attempt to enter Sleep mode while one of these
conditions has not been satisfied will result in a short reset (3.6 ms min. pulse width; see
Section 6.5.1 and Table 11).
In Sleep mode, V1 and V2 are off and the bus transceivers will be switched off (Off mode;
STBCC/STBCL = 0; see Table 6) or in a low-power state (Lowpower mode;
STBCC/STBCL = 1) with bus wake-up detection active - see Section 6.7.1 and
Section 6.8.1). The watchdog is off and the reset pin is LOW.
A CAN, LIN or local wake-up event will cause the SBC to switch from Sleep mode to
Standby mode, generating a (short or long; see Section 6.5.1) system reset. The value of
the mode control bits (MC) will be changed to 00 and V1 will be enabled.
6.1.6 Overtemp mode
The SBC will enter Overtemp mode from Normal mode or Standby mode when the chip
temperature exceeds the overtemperature protection activation threshold, Tth(act)otp
,
In Overtemp mode, the voltage regulators are switched off and the bus systems are in a
high-resistive state. When the SBC enters Overtemp mode, the RSTN pin is driven LOW
and the limp home control bit, LHC, is set so that the LIMP pin is driven LOW.
The chip temperature must drop a hysteresis level below the overtemperature shutdown
threshold before the SBC can exit Overtemp mode. After leaving Overtemp mode the
SBC enters Standby mode and a system reset is generated (reset pulse width of tw(rst)
,
long or short; see Section 6.5.1 and Table 11).
6.2 SPI
6.2.1 Introduction
The Serial Peripheral Interface (SPI) provides the communication link with the
microcontroller, supporting multi-slave operations. The SPI is configured for full duplex
data transfer, so status information is returned when new control data is shifted in. The
interface also offers a read-only access option, allowing registers to be read back by the
application without changing the register content.
The SPI uses four interface signals for synchronization and data transfer:
• SCSN: SPI chip select; active LOW
• SCK: SPI clock; default level is LOW due to low-power concept
• SDI: SPI data input
• SDO: SPI data output; floating when pin SCSN is HIGH
Bit sampling is performed on the falling clock edge and data is shifted on the rising clock
edge (see Figure 4).
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
10 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
SCS
SCK
01
sampled
MSB
02
03
04
15
16
SDI
X
14
14
13
13
12
12
01
01
LSB
LSB
X
MSB
SDO
X
floating
floating
mce634
Fig 4. SPI timing protocol
6.2.2 Register map
The first three bits (A2, A1 and A0) of the message header define the register address.
The fourth bit (RO) defines the selected register as read/write or read only.
Table 3.
Register map
Address bits 15, 14 and 13
Write access bit 12 = 0
Read/Write access bits 11... 0
WD_and_Status register
Mode_Control register
Int_Control register
000
001
010
011
0 = read/write, 1 = read only
0 = read/write, 1 = read only
0 = read/write, 1 = read only
0 = read/write, 1 = read only
Int_Status register
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
11 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.2.3 WD_and_Status register
Table 4.
WD_and_Status register
Symbol Access Power-on Description
Bit
default
15:13 A2, A1, A0
R
000
register address
access status
12
RO
R/W
0
0: register set to read/write
1: register set to read only
watchdog mode control
11
WMC
R/W
R/W
0
0: Normal mode: watchdog in Window mode; Standby mode: watchdog in
Timeout mode
1: Normal mode: watchdog in Timeout mode; Standby mode: watchdog in
Off mode
10:8 NWP[1]
100
nominal watchdog period
000: 8 ms
001: 16 ms
010: 32 ms
011: 64 ms
100: 128 ms
101: 256 ms
110: 1024 ms
111: 4096 ms
7
6
WOS/SWR R/W
-
-
watchdog off status/software reset
0: WDOFF pin LOW; watchdog mode determined by bit WMC
1: watchdog disabled due to HIGH level on pin WDOFF; results in software
reset
V1S
V2S
R
R
V1 status
0: V1 output voltage above 90 % undervoltage recovery threshold
(Vuvr; see Table 10)
1: V1 output voltage below 90 % undervoltage detection threshold
(Vuvd; see Table 10)
5
-
V2 status
0: V2 output voltage above undervoltage release threshold
(Vuvr; see Table 10)
1: V2 output voltage below undervoltage detection threshold
(Vuvd; see Table 10)
4
WLS1
R
R
R
-
wake-up 1 status
0: WAKE1 input voltage below switching threshold (Vth(sw)
)
1: WAKE1 input voltage above switching threshold (Vth(sw)
)
)
3
WLS2
-
wake-up 2 status
0: WAKE2 input voltage below switching threshold (Vth(sw)
)
1: WAKE2 input voltage above switching threshold (Vth(sw)
2:0
reserved
000
[1] Bit NWP is set to it’s default value (100) after a reset.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
12 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.2.4 Mode_Control register
Table 5.
Bit
Mode_Control register
Symbol
Access Power-on Description
default
15:13 A2, A1, A0 R
001
0
register address
access status
12
RO
R/W
0: register set to read/write
1: register set to read only
mode control
11:10 MC
R/W
00
00: Standby mode
01: Sleep mode
10: Normal mode; V2 off
11: Normal mode; V2 on
9
8
7
6
5
4
LHWC[1]
R/W
R/W
R/W
R/W
R/W
R/W
1
0
0
0
0
0
limp home warning control
0: no limp home warning
1: limp home warning is set; next reset will activate LIMP output
limp home control
LHC[2]
ENC
LSC
0: LIMP pin set floating
1: LIMP pin driven LOW
enable control
0: EN pin driven LOW
1: EN pin driven HIGH in Normal mode
LIN slope control
0: normal slope, 20 kbit/s
1: low slope, 10.4 kbit/s
WBC
PDC
wake bias control
0: WBIAS floating if WSEn = 0; 16 ms sampling if WSEn = 1
1: WBIAS on if WSEn = 0; 64 ms sampling if WSEn = 1
power distribution control
0: V1 threshold current for activating the external PNP transistor; load current
rising; Ith(act)PNP = 85 mA; V1 threshold current for deactivating the external
PNP transistor; load current falling; Ith(deact)PNP = 50 mA; see Figure 7
1: V1 threshold current for activating the external PNP transistor; load current
rising; Ith(act)PNP = 50 mA; V1 threshold current for deactivating the external
PNP transistor; load current falling; Ith(deact)PNP = 15 mA; see Figure 7
3:0
reserved
R
0000
[1] Bit LHWC is set to 1 after a reset.
[2] Bit LHC is set to 1 after a reset, if LHWC was set to 1 prior to the reset.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
13 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.2.5 Int_Control register
Table 6.
Bit
Int_Control register
Symbol
Access Power-on Description
default
15:13 A2, A1, A0 R
010
0
register address
access status
12
11
10
9
RO
R/W
R/W
R/W
R/W
0: register set to read/write
1: register set to read only
V1UIE
V2UIE
STBCL
0
0
0
V1 undervoltage interrupt enable
0: V1 undervoltage warning interrupts cannot be requested
1: V1 undervoltage warning interrupts can be requested
V2 undervoltage interrupt enable
0: V2 undervoltage warning interrupts cannot be requested
1: V2 undervoltage warning interrupts can be requested
LIN standby control
0: When the SBC is in Normal mode (MC = 1x):
LIN is in Active mode. The wake-up flag (visible on RXDL) is cleared
regardless of the value of VBAT
.
When the SBC is in Standby/Sleep mode (MC = 0x):
LIN is in Off mode. Bus wake-up detection is disabled. LIN wake-up
interrupts cannot be requested.
1: LIN is in Lowpower mode with bus wake-up detection enabled, regardless
of the SBC mode (MC = xx). LIN wake-up interrupts can be requested.
8
reserved
WIC1
R
0
7:6
R/W
00
wake-up interrupt 1 control
00: wake-up interrupt 1 disabled
01: wake-up interrupt 1 on rising edge
10: wake-up interrupt 1 on falling edge
11: wake-up interrupt 1 on both edges
wake-up interrupt 2 control
5:4
WIC2
R/W
R/W
00
00: wake-up interrupt 2 disabled
01: wake-up interrupt 2 on rising edge
10: wake-up interrupt 2 on falling edge
11: wake-up interrupt 2 on both edges
CAN standby control
3
STBCC
0
0: When the SBC is in Normal mode (MC = 1x):
CAN is in Active mode. The wake-up flag (visible on RXDC) is cleared
regardless of V2 output voltage.
When the SBC is in Standby/Sleep mode (MC = 0x):
CAN is in Off mode. Bus wake-up detection is disabled. CAN wake-up
interrupts cannot be requested.
1: CAN is in Lowpower mode with bus wake-up detection enabled,
regardless of the SBC mode (MC = xx). CAN wake-up interrupts can be
requested.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
14 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 6.
Bit
Int_Control register
Symbol
Access Power-on Description
default
2
RTHC
R/W
0
reset threshold control
0: The reset threshold is set to the 90 % V1 undervoltage detection voltage
(Vuvd; see Table 10)
1: The reset threshold is set to the 70 % V1 undervoltage detection voltage
(Vuvd; see Table 10)
1
0
WSE1
WSE2
R/W
R/W
0
0
WAKE1 sample enable
0: sampling continuously
1: sampling of WAKE1 is synchronized with WBIAS (sample rate controlled
by WBC)
WAKE2 sample enable
0: sampling continuously
1: sampling of WAKE1 is synchronized with WBIAS (sample rate controlled
by WBC)
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
15 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.2.6 Int_Status register
Table 7.
Bit
Int_Status register[1]
Symbol
Access Power-on Description
default
15:13 A2, A1, A0 R
011
0
register address
access status
12
11
10
9
RO
R/W
R/W
R/W
R/W
0: register set to read/write
1: register set to read only
V1UI
V2UI
LWI
0
0
0
V1 undervoltage interrupts
0: no V1 undervoltage warning interrupt pending
1: V1 undervoltage warning interrupt pending
V2 undervoltage interrupts
0: no V2 undervoltage warning interrupt pending
1: V2 undervoltage warning interrupt pending
LIN wake-up interrupt
0: no LIN wake-up interrupt pending
1: LIN wake-up interrupt pending
8
7
reserved
CI
R
0
0
R/W
cyclic interrupt
0: no cyclic interrupt pending
1: cyclic interrupt pending
wake-up interrupt 1
6
WI1
R/W
R/W
R/W
R/W
R
0
0: no wake-up interrupt 1 pending
1: wake-up interrupt 1 pending
power-on status interrupt
5
POSI
WI2
1
0: no power-on interrupt pending
1: power-on interrupt pending
wake-up interrupt 2
4
0
0: no wake-up interrupt 2 pending
1: wake-up interrupt 2 pending
CAN wake-up interrupt
3
CWI
0
0: no CAN wake-up interrupt pending
1: CAN wake-up interrupt pending
2:0
reserved
000
[1] An interrupt can be cleared by writing 1 to the relevant bit in the Int_Status register.
6.3 On-chip oscillator
The on-chip oscillator provides the timing reference for the on-chip watchdog and the
internal timers. The on-chip oscillator is supplied by an internal supply that is connected to
BAT and is independent of V1/V2.
V
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
16 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.4 Watchdog (UJA1075/xx/WD versions)
Three watchdog modes are supported: Window, Timeout and Off. The watchdog period is
programmed via the NWP control bits in the WD_and_Status register (see Table 4). The
default watchdog period is 128 ms.
A watchdog trigger event is any write access to the WD_and_Status register. When the
watchdog is triggered, the watchdog timer is reset.
In watchdog Window mode, a watchdog trigger event within a closed watchdog window
(i.e. the first half of the window before ttrig(wd)1) will generate an SBC reset. If the watchdog
is triggered before the watchdog timer overflows in Timeout or Window mode, or within
the open watchdog window (after ttrig(wd)1 but before ttrig(wd)2), the timer restarts
immediately.
The following watchdog events result in an immediate system reset:
• the watchdog overflows in Window mode
• the watchdog is triggered in the first half of the watchdog period in Window mode
• the watchdog overflows in Timeout mode while a cyclic interrupt (CI) is pending
• the state of the WDOFF pin changes in Normal mode or Standby mode
• the watchdog mode control bit (WMC) changes state in Normal mode
After a watchdog reset (short reset; see Section 6.5.1 and Table 11), the default watchdog
period is selected (NWP = 100). The watchdog can be switched off completely by forcing
pin WDOFF HIGH. The watchdog can also be switched off by setting bit WMC to 1 in
Standby mode. If the watchdog was turned off by setting WMC, any pending interrupt will
re-enable it.
Note that the state of bit WMC cannot be changed in Standby mode if an interrupt is
pending. Any attempt to change WMC when an interrupt is pending will be ignored.
6.4.1 Watchdog Window behavior
The watchdog runs continuously in Window mode.
If the watchdog overflows, or is triggered in the first half of the watchdog period (less than
ttrig(wd)1 after the start of the watchdog period), a system reset will be performed.
Watchdog overflow occurs if the watchdog is not triggered within ttrig(wd)2 after the start of
watchdog period.
If the watchdog is triggered in the second half of the watchdog period (at least ttrig(wd)1, but
not more than ttrig(wd)2, after the start of the watchdog period), the watchdog will be reset.
The watchdog is in Window mode when pin WDOFF is LOW, the SBC is in Normal mode
and the watchdog mode control bit (WMC) is set to 0.
6.4.2 Watchdog Timeout behavior
The watchdog runs continuously in Timeout mode. It can be reset at any time by a
watchdog trigger. If the watchdog overflows, the cyclic interrupt (CI) bit is set. If a CI is
already pending, a system reset is performed.
The watchdog is in Timeout mode when pin WDOFF is LOW and:
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
17 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
• the SBC is in Standby mode and bit WMC = 0 or
• the SBC is in Normal mode and bit WMC = 1
6.4.3 Watchdog Off behavior
The watchdog is disabled in this state.
The watchdog is in Off mode when:
• the SBC is in Off, Overtemp or Sleep modes
• the SBC is in Standby mode and bit WMC = 1
• the SBC is in any mode and the WDOFF pin is HIGH
6.5 System reset
The following events will cause the SBC to perform a system reset:
• V1 undervoltage (reset pulse length selected via external pull-up resistor on RSTN
pin)
• An external reset (RSTN forced LOW)
• Watchdog overflow (Window mode)
• Watchdog overflow in Timeout mode with cyclic interrupt (CI) pending
• Watchdog triggered too early in Window mode
• WMC value changed in Normal mode
• WDOFF pin state changed
• SBC goes to Sleep mode (MC set to 01; see Table 5) while INTN is driven LOW
• SBC goes to Sleep mode (MC set to 01; see Table 5) while
STBCC = STBCL = WIC1 = WIC2 = 0
• SBC goes to Sleep mode (MC set to 01; see Table 5) while wake-up pending
• Software reset (SWR = 1)
• SBC leaves Overtemp mode (reset pulse length selected via external pull-up resistor
on RSTN pin)
A watchdog overflow in Timeout mode requests a cyclic interrupt (CI), if a CI is not already
pending.
The UJA1075 provides three signals for dealing with reset events:
• RSTN input/output for performing a global ECU system reset or forcing an external
reset
• EN pin, a fail-safe global enable output
• LIMP pin, a fail-safe limp home output
6.5.1 RSTN pin
A system reset is triggered if the bidirectional RSTN pin is forced LOW for at least tfltr by
the microcontroller (external reset). A reset pulse is output on RSTN by the SBC when a
system reset is triggered internally.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
18 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
The reset pulse width (tw(rst)) is selectable (short or long) if the system reset was
generated by a V1 undervoltage event (see Section 6.6.2) or by the SBC leaving Off
(VBAT > Vth(det)pon) or Overtemp (temperature < Tth(rel)otp) modes. A short reset pulse is
selected by connecting a 900 Ω ±10 % resistor between pins RSTN and V1. If a resistor is
not connected, the reset pulse will be long (see Table 11).
In all other cases (e.g. watchdog-related reset events) the reset pulse length will be short.
6.5.2 EN output
The EN pin can be used to control external hardware, such as power components, or as a
general-purpose output when the system is running properly.
In Normal and Standby modes, the microcontroller can set the EN control bit (bit ENC in
the Mode_Control register; see Table 5) via the SPI interface. Pin EN will be HIGH when
ENC = 1 and MC = 10 or 11. A reset event will cause pin EN to go LOW. EN pin behavior
is illustrated in Figure 5.
STANDBY
NORMAL
STANDBY
mode
ENC
EN
RSTN
015aaa074
Fig 5. Behavior of EN pin
6.5.3 LIMP output
The LIMP pin can be used to enable the so called ‘limp home’ hardware in the event of an
ECU failure. Detectable failure conditions include SBC overtemperature events, loss of
watchdog service, RSTN or V1 clamped LOW and user-initiated or external reset events.
The LIMP pin is a battery-related, active-LOW, open-drain output.
A system reset will cause the limp home warning control bit (bit LHWC in the
Mode_Control register; see Table 5) to be set. If LHWC is already set when the system
reset is generated, bit LHC will be set which will force the LIMP pin LOW. The application
should clear LHWC after each reset event to ensure the LIMP output is not activated
during normal operation.
In Overtemp mode, bit LHC is always set and, consequently, the LIMP output is always
active. If the application manages to recover from the event that activated the LIMP
output, LHC can be cleared to deactivate the LIMP output.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
19 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.6 Power supplies
6.6.1 Battery pin (BAT)
The SBC contains a single supply pin, BAT. An external diode is needed in series to
protect the device against negative voltages. The operating range is from 4.5 V to 28 V.
The SBC can handle maximum voltages up to 40 V.
If the voltage on pin BAT falls below the power-off detection threshold, Vth(det)poff, the SBC
immediately enters Off mode, which means that the voltage regulators and the internal
logic are shut down. The SBC leaves Off mode for Standby mode as soon as the voltage
rises above the power-on detection threshold, Vth(det)pon. The POSI bit in the Int_Status
register is set to 1 when the SBC leaves Off mode.
6.6.2 Voltage regulator V1
Voltage regulator V1 is intended to supply the microcontroller, its periphery and additional
transceivers. V1 is supplied by pin BAT and delivers up to 250 mA at 3.3 V or 5 V
(depending on the UJA1075 version).
To prevent the device overheating at high ambient temperatures or high average currents,
an external PNP transistor can be connected as illustrated in Figure 6. In this
configuration, the power dissipation is distributed between the SBC and the PNP
transistor. Bit PDC in the Mode_Control register (Table 5) is used to regulate how the
power dissipation is distributed − if PDC = 0, the PNP transistor will be activated when the
load current reaches 85 mA (50 mA if PDC = 1) at Tvj = 150 °C. V1 will continue to deliver
85 mA while the transistor delivers the additional load current (see Figure 7 and Figure 8).
VEXCTRL
battery
VEXCC
UJA107x
BAT
V1
015aaa098
Fig 6. External PNP transistor control circuit
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
20 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
250 mA
215 mA
85 mA
50 mA
load
current
I
= 85 mA
th(act)PNP
(PDC = 0)
I
= 50 mA
th(deact)PNP
I
(PDC = 0)
V1
165 mA
PNP
current
015aaa111
Fig 7. V1 and PNP currents at a slow ramping load current of 250 mA (PDC = 0)
Figure 7 illustrates how V1 and the PNP transistor combine to supply a slow ramping load
current of 250 mA with PDC = 0. Any additional load current requirement will be supplied
by the PNP transistor, up to its current limit. If the load current continues to rise, IV1 will
increase above the selected PDC threshold (to a maximum of 250 mA).
For a fast ramping load current, V1 will deliver the required load current (to a maximum of
250 mA) until the PNP transistor has switched on. Once the transistor has been activated,
V1 will deliver 85 mA (PDC = 0) with the transistor contributing the balance of the load
current (see Figure 8).
250 mA
load
current
250 mA
I
= 85 mA
th(act)PNP
(PDC = 0)
I
0 mA
V1
−165 mA
165 mA
PNP
current
015aaa075
Fig 8. V1 and PNP currents at a fast ramping load current of 250 mA (PDC = 0)
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
21 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
For short-circuit protection, a resistor needs to be connected between pins V1 and
VEXCC to allow the current to be monitored. This resistor limits the current delivered by
the external transistor. If the voltage difference between pins VEXCC and V1 reaches
V
th(act)Ilim, the PNP current limiting activation threshold voltage, the transistor current will
not increase further.
The thermal performance of the transistor needs to be considered when calculating the
value of this resistor. A 3.3 Ω resistor was used with the BCP52-16 (NXP Semiconductors)
employed during testing. Note that the selection of the transistor is not critical. In general,
any PNP transistor with a current amplification factor (β) of between 60 and 500 can be
used.
If an external PNP transistor is not used, pin VEXCC must be connected to V1 while pin
VEXCTRL can be left open.
One advantage of this scalable voltage regulator concept is that there are no PCB layout
restrictions when using the external PNP. The distance between the UJA1075 and the
external PNP doesn’t affect the stability of the regulator loop because the loop is realized
within the UJA1075. Therefore, it is recommended that the distance between the
UJA1075 and PNP transistor be maximized for optimal thermal distribution.
The output voltage on V1 is monitored continuously and a system reset signal is
generated if an undervoltage event occurs. A system reset is generated if the voltage on
V1 falls below the undervoltage detection voltage (Vuvd; see Table 10). The reset
threshold (90 % or 70 % of the nominal value) is set via the Reset Threshold Control bit
(RTHC) in the Int_Control register (Table 6). In addition, an undervoltage warning (a V1UI
interrupt) will be generated at 90 % of the nominal output voltage. The status of V1 can be
read via bit V1S in the WD_and_Status register (Table 4).
6.6.3 Voltage regulator V2
Voltage regulator V2 is reserved for the high-speed CAN transceiver, providing a 5 V
supply.
V2 can be activated and deactivated via the MC bits in the Mode_Control register
(Table 5). An undervoltage warning (a V2UI interrupt) is generated when the output
voltage drops below 90 % of its nominal value. The status of V2 can be read via bit V2S in
the WD_and_Status register (Table 4) in Normal mode (V2S = 1 in all other modes).
V2 can be deactivated (MC = 10) to allow the internal CAN transceiver to be supplied from
an external source or from V1. The alternative voltage source must be connected to pin
V2. All internal functions (e.g. undervoltage protection) will work normally.
6.7 CAN transceiver
The analog section of the UJA1075 CAN transceiver corresponds to that integrated into
the TJA1042/TJA1043. The transceiver is designed for high-speed (up to 1 Mbit/s) CAN
applications in the automotive industry, providing differential transmit and receive
capability to a CAN protocol controller.
6.7.1 CAN operating modes
6.7.1.1 Active mode
The CAN transceiver is in Active mode when:
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
22 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
• the SBC is in Normal mode (MC = 10 or 11)
• the transceiver is enabled (bit STBCC = 0; see Table 6)
and
• V2 is enabled and its output voltage is above its undervoltage threshold, Vuvd
or
• V2 is disabled but an external voltage source, or V1, connected to pin V2 is above its
undervoltage threshold (see Section 6.6.3)
In CAN Active mode, the transceiver can transmit and receive data via the CANH and
CANL pins. The differential receiver converts the analog data on the bus lines into digital
data which is output on pin RXDC. The transmitter converts digital data generated by a
CAN controller, and input on pin TXDC, to signals suitable for transmission over the bus
lines.
6.7.1.2 Lowpower/Off modes
The CAN transceiver will be in Lowpower mode with bus wake-up detection enabled if bit
STBCC = 1 (see Table 6). The CAN transceiver can be woken up remotely via pins CANH
and CANL in Lowpower mode.
When the SBC is in Standby mode or Sleep mode (MC = 00 or 01), the CAN transceiver
will be in Off mode if bit STBCC = 0. The CAN transceiver is powered down completely in
Off mode to minimize quiescent current consumption.
A filter at the receiver input prevents unwanted wake-up events occurring due to
automotive transients or EMI.
A recessive-dominant-recessive-dominant sequence must occur on the CAN bus within
the wake-up timeout time (tto(wake)) to pass the wake-up filter and trigger a wake-up event
(see Figure 9; note that additional pulses may occur between the recessive/dominant
phases). The minimum recessive/dominant bus times for CAN transceiver wake-up
(twake(busrec)min and twake(busdom)min) must be satisfied (see Table 11).
recessive
dominant
recessive
dominant
wake-up
t
< t
to(wake)
wake
015aaa107
Fig 9. CAN wake-up timing diagram
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
23 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.7.2 Split circuit
Pin SPLIT provides a DC stabilized voltage of 0.5VV2. It is activated in CAN Active mode
only. Pin SPLIT is floating in CAN Lowpower and Off modes. The VSPLIT circuit can be
used to stabilize the recessive common-mode voltage by connecting pin SPLIT to the
center tap of the split termination (see Figure 10).
A transceiver in the network that is not supplied and that generates a significant leakage
current from the bus lines to ground, can result in a recessive bus voltage of < 0.5VV2. In
this event, the split circuit will stabilize the recessive voltage at 0.5VV2. So a start of
transmission will not generate a step in the common-mode signal which would lead to
poor ElectroMagnetic Emission (EME) performance.
V2
UJA1075
CANH
R
R
60 Ω
60 Ω
V
= 0.5 V
CC
SPLIT
CANL
SPLIT
in normal mode;
otherwise floating
GND
015aaa120
Fig 10. Stabilization circuitry and application using the SPLIT pin
6.7.3 Fail-safe features
6.7.3.1 TXDC dominant time-out function
A TXDC dominant time-out timer is started when pin TXDC is forced LOW. If the LOW
state on pin TXDC persists for longer than the TXDC dominant time-out time (tto(dom)TXDC),
the transmitter will be disabled, releasing the bus lines to recessive state. This function
prevents a hardware and/or software application failure from driving the bus lines to a
permanent dominant state (blocking all network communications). The TXDC dominant
time-out timer is reset when pin TXDC goes HIGH. The TXDC dominant time-out time
also defines the minimum possible bit rate of 10 kbit/s.
6.7.3.2 Pull-up on TXDC pin
Pin TXDC has an internal pull-up towards VV1 to ensure a safe defined state in case the
pin is left floating.
6.8 LIN transceiver
The analog sections of the UJA1075 LIN transceiver is identical to that integrated into the
TJA1021.
The transceiver is the interface between the LIN master/slave protocol controller and the
physical bus in a LIN. It is primarily intended for in-vehicle sub-networks using baud rates
from 1 kBd up to 20 kBd and is LIN 2.0/LIN 2.1/SAE J2602 compliant.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
24 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
6.8.1 LIN operating modes
6.8.1.1 Active mode
The LIN transceiver will be in Active mode when:
• the SBC is in Normal mode (MC = 10 or 11) and
• the transceiver is enabled (STBCL = 0; see Table 6) and
• the battery voltage (VBAT) is above the LIN undervoltage recovery threshold, Vuvr(LIN)
.
In LIN Active mode, the transceiver can transmit and receive data via the LIN bus pin.
The receiver detects data streams on the LIN bus pin (LIN) and transfers them to the
microcontroller via pin RXDL (see Figure 1) - LIN recessive is represented by a HIGH
level on RXDL, LIN dominant by a LOW level.
The transmit data streams of the protocol controller at the TXDL input (pin TXDL) are
converted by the transmitter into bus signals with optimized slew rate and wave shaping to
minimize EME.
6.8.1.2 Lowpower/Off modes
The LIN transceiver will be in Lowpower mode with bus wake-up detection enabled if bit
STBCL = 1 (see Table 6). The LIN transceiver can be woken up remotely via pin LIN in
Lowpower mode.
When the SBC is in Standby mode or Sleep mode (MC = 00 or 01), the LIN transceiver
will be in Off mode if bit STBCL = 0. The LIN transceiver is powered down completely in
Off mode to minimize quiescent current consumption.
Filters at the receiver inputs prevent unwanted wake-up events due to automotive
transients or EMI.
The wake-up event must remain valid for at least the minimum dominant bus time for
wake-up of the LIN transceiver, twake(busdom)min (see Table 11).
6.8.2 Fail-safe features
6.8.2.1 General fail-safe features
The following fail-safe features have been implemented:
• Pin TXDL has an internal pull-up towards VV1 to guarantee a safe, defined state if this
pin is left floating
• The current of the transmitter output stage is limited in order to protect the transmitter
against short circuits to pin BAT
• A loss of power (pins BAT and GND) has no impact on the bus lines or on the
microcontroller. There will be no reverse currents from the bus.
6.8.2.2 TXDL dominant time-out function
A TXDL dominant time-out timer circuit prevents the bus lines being driven to a permanent
dominant state (blocking all network communications) if TXDL is forced permanently LOW
by a hardware and/or software application failure. The timer is triggered by a negative
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
25 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
edge on pin TXDL. If the pin remains LOW for longer than the TXDL dominant time-out
time (tto(dom)TXDL), the transmitter is disabled, driving the bus lines to a recessive state.
The timer is reset by a positive edge on the TXDL pin.
6.9 Local wake-up input
The SBC provides 2 local wake-up pins (WAKE1 and WAKE2). The edge sensitivity
(falling, rising or both) of the wake-up pins can be configured independently via the WIC1
and WIC2 bits in the Int_Control register Table 6). These bits can also be used to disable
wake-up via the wake-up pins. When wake-up is enabled, a valid wake-up event on either
of these pins will cause a wake-up interrupt to be generated in Standby mode or Normal
mode. If the SBC is in Sleep mode when the wake-up event occurs, it will wake up and
enter Standby mode. The status of the wake-up pins can be read via the wake-up level
status bits (WLS1 and WLS2) in the WD_and_Status register (Table 4).
Note that bits WLS1 and WLS2 are only active when at least one of the wake up interrupts
is enabled (WIC1 ≠ 00 or WIC2 ≠ 00).
enable bias
disable bias
WBIASI
(internal)
WBIAS pin
WAKEx pin
Wake-up int
disable bias
wake level latched
015aaa078
Fig 11. Wake-up pin sampling synchronized with WBIAS signal
The sampling of the wake-up pins can be synchronized with the WBIAS signal by setting
bits WSE1 and WSE2 in the Int_Control register to 1 (if WSEx = 0, wake-up pins are
sampled continuously). The sampling will be performed on the rising edge of WBIAS (see
Figure 11). The sampling time, 16 ms or 64 ms, is selected via the Wake Bias Control bit
(WBC) in the Mode_Control register.
Figure 12 shows typical circuit for implementing cyclic sampling of the wake-up inputs.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
26 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
UJA1075
BAT
47 kΩ
47 kΩ
PDTA144E
WBIAS
biasing of
switches
WAKE1
WAKE2
t
sample of
WAKEx
sample of
WAKEx
sample of
WAKEx
GND
015aaa127
Fig 12. Typical application for cyclic sampling of wake-up signals
6.10 Interrupt output
Pin INTN is an active-LOW, open-drain interrupt output. It is driven LOW when at least
one interrupt is pending. An interrupt can be cleared by writing 1 to the corresponding bit
in the Int_Status register (Table 7). Clearing bits LWI and CWI in Standby mode only
clears the interrupt status bits and not the pending wake-up. The pending wake-up is
cleared on entering Normal mode and when the corresponding standby control bit
(STBCC or STBCL) is 0.
On devices that contain a watchdog, the Cyclic Interrupt (CI) is enabled when the
watchdog switches to Timeout mode while the SBC is in Standby mode or Normal mode
(provided WDOFF = LOW). A CI is generated if the watchdog overflows in Timeout mode.
The CI is provided to alert the microcontroller when the watchdog overflows in Timeout
mode. The CI will wake up the microcontroller from a μC standby mode. After polling the
Int_Status register, the microcontroller will be aware that the application is in cyclic wake
up mode. It can then perform some checks on CAN and LIN before returning to the μC
standby mode.
6.11 Temperature protection
The temperature of the SBC chip is monitored in Normal and Standby modes. If the
temperature is too high, the SBC will go to Overtemp mode, where the RSTN pin is driven
LOW and limp home is activated. In addition, the voltage regulators and the CAN and LIN
transmitters are switched off (see also Section 6.1.6 “Overtemp mode”). When the
temperature falls below the temperature shutdown threshold, the SBC will go to Standby
mode. The temperature shutdown threshold is between 165 °C and 200 °C.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
27 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
7. Limiting values
Table 8.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
Min
Max
Unit
Vx
voltage on pin x
DC value
pins V1, V2 and INTN
−0.3
−0.3
7
V
V
pins TXDC, RXDC, EN, SDI, SDO, SCK, SCSN,
TXDL, RXDL, RSTN and WDOFF
VV1 + 0.3
pin VEXCC
VV1 − 0.3
−58
VV1 + 0.35
+58
V
V
pins WAKE1, WAKE2 and WBIAS; with respect to
any other pin
pin LIMP and BAT
pin VEXCTRL
−0.3
−0.3
−58
+40
V
V
V
VBAT + 0.3
+58
pins CANH, CANL, SPLIT and LIN; with respect to
any other pin
pin DLIN; with respect to any other pin
VBAT − 0.3 +58
V
[1]
IR(V1-BAT) reverse current from VV1 ≤ 5 V
-
250
mA
pin V1 to pin BAT
IDLIN
Vtrt
current on pin DLIN
transient voltage
−65
0
mA
V
[2]
on pins
BAT: via reverse polarity diode/capacitor
−150
+100
CANL, CANH, SPLIT: coupling with two capacitors
on the bus lines
LIN: coupling via 1 nF capacitor
DLIN: via 1 kΩ resistor
[3]
[4]
VESD
electrostatic
discharge voltage
IEC 61000-4-2
pins BAT with capacitor, CANH, CANL and LIN; via
a series resistor on pins SPLIT, DLIN, WAKE1 and
WAKE2
−6
−8
+6
+8
kV
kV
[5]
[6]
HBM
pins CANH, CANL, LIN, SPLIT, DLIN, WAKE1 and
WAKE2
pin BAT; referenced to ground
−4
+4
+2
+2
+2
kV
kV
kV
kV
pin TEST2; referenced to pin BAT
−1.25
−2
pin TEST2; referenced to other reference pins
any other pin
MM
−2
[7]
any pin
−300
+300
V
[8]
CDM
corner pins
any other pin
−750
−500
−40
+750
+500
+150
V
V
[9]
Tvj
virtual junction
temperature
°C
Tstg
storage temperature
−55
+150
°C
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
28 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 8.
Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
Min
Max
Unit
Tamb
ambient
−40
+125
°C
temperature
[1] A reverse diode connected between V1 (anode) and BAT (cathode) limits the voltage drop voltage from V1(+) to BAT (-).
[2] Verified by an external test house to ensure pins can withstand ISO 7637 part 2 automotive transient test pulses 1, 2a, 3a and 3b.
[3] IEC 61000-4-2 (150 pF, 330 Ω).
[4] ESD performance according to IEC 61000-4-2 (150 pF, 330 Ω) has been verified by an external test house for pins BAT, CANH, CANL,
LIN1, LIN2, WAKE1 and WAKE2. The result is equal to or better than ±6 kV.
[5] Human Body Model (HBM): according to AEC-Q100-002 (100 pF, 1.5 kΩ).
[6] V1, V2 and BAT connected to GND, emulating application circuit.
[7] Machine Model (MM): according to AEC-Q100-003 (200 pF, 0.75 μH, 10 Ω).
[8] Charged Device Model (CDM): according to AEC-Q100-011 (field Induced charge; 4 pF).
[9] In accordance with IEC 60747-1. An alternative definition of virtual junction temperature is: Tvj = Tamb + P × Rth(vj-a), where Rth(vj-a) is a
fixed value to be used for the calculation of Tvj. The rating for Tvj limits the allowable combinations of power dissipation (P) and ambient
temperature (Tamb).
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
29 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
8. Thermal characteristics
optional heatsink top layer
optional heatsink top layer
PCB copper area:
(bottom layer)
2
2 cm
optional heatsink top layer
PCB copper area:
(bottom layer)
8 cm
2
015aaa137
Layout conditions for Rth(j-a) measurements: board finish thickness 1.6 mm ±10 %, double-layer
board, board dimensions 129 mm × 60 mm, board Material FR4, Cu thickness 0.070 mm, thermal
via separation 1.2 mm, thermal via diameter 0.3 mm ±0.08 mm, Cu thickness on vias 0.025 mm.
Optional heat sink top layer of 3.5 mm × 25 mm will reduce thermal resistance (see Figure 14).
Fig 13. HTSSOP PCB
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
30 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
015aaa138
90
R
th(j-a)
(K/W)
70
without heatsink top layer
50
30
with heatsink top layer
2
0
4
6
8
10
2
PCB Cu heatsink area (cm )
Fig 14. HTSSOP32 thermal resistance junction to ambient as a function of PCB copper
area
Table 9.
Symbol Parameter
Rth(j-a) thermal resistance from junction to
ambient
Thermal characteristics
Conditions
Typ Unit
[1]
[2]
single-layer board
four-layer board
78
39
K/W
K/W
[1] According to JEDEC JESD51-2 and JESD51-3 at natural convection on 1s board.
[2] According to JEDEC JESD51-2, JESD51-5 and JESD51-7 at natural convection on 2s2p board. Board with
two inner copper layers (thickness: 35 μm) and thermal via array under the exposed pad connected to the
first inner copper layer.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
31 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
9. Static characteristics
Table 10. Static characteristics
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Supply; pin BAT
VBAT battery supply voltage
IBAT battery supply current
Parameter
Conditions
Min
Typ
Max
Unit
4.5
-
28
V
MC = 00 (Standby; V1 on, V2 off)
STBCC = STBCL = 1 (CAN/LIN
wake-up enabled)
WIC1 = WIC2 = 11 (WAKE interrupts
enabled); 7.5 V < VBAT < 28 V
IV1 = 0 mA; VRSTN = VSCSN = VV1
VTXDL = VTXDC = VV1; VSDI = VSCK = 0 V
Tvj = −40 °C
Tvj = 25 °C
Tvj = 150 °C
-
-
-
83
76
68
98
88
80
μA
μA
μA
MC = 01 (Sleep; V1 off, V2 off)
STBCC = STBCL = 1 (CAN/LIN
wake-up enabled)
WIC1 = WIC2 = 11 (WAKE interrupts
enabled)
7.5 V < VBAT < 28 V; VV1 = 0 V
Tvj = −40 °C
Tvj = 25 °C
Tvj = 150 °C
-
-
-
-
60
56
51
1.1
71
65
59
2
μA
μA
μA
μA
contributed by LIN wake-up receiver
STBCL = 1
VLIN = VBAT
5.5 V < VBAT < 28 V
contributed by CAN wake-up receiver
STBCC = 1; VCANH = VCANL = 2.5 V
5.5 V < VBAT < 28 V
1
0
6
5
13
10
μA
μA
contributed by WAKEn pin edge
detectors
WIC1 = WIC2 = 11
VWAKE1 = VWAKE2 = VBAT
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
32 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 10. Static characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ
Max
50
3
Unit
μA
IBAT(add)
additional battery supply
current
5.1 V < VBAT < 7.5 V
-
-
-
-
4.5 V < VBAT < 5.1 V
V1 on (5 V version)
mA
V2 on; MC = 11
V2UIE = 1; IV2 = 0 mA
100
-
-
-
950
10
μA
CAN Active mode (recessive)
STBCC = 0; MC = 1x; VTXDC = VV1
ICANH = ICANL = 0 mA
mA
5.5 V < VBAT < 28 V
CAN active (dominant)
STBCC = 0; MC = 1x; VTXDC = 0 V
R(CANH-CANL) = 45 Ω
-
-
-
-
-
-
-
-
70
mA
μA
5.5 V < VBAT < 28 V
LIN Active mode (recessive)
STBCL = 0; MC = 1x
1300
5
VTXDL= VV1; IDLIN = ILIN = 0 mA
5.5 V < VBAT < 28 V
LIN Active mode (dominant);
STBCL = 0; MC = 1x
mA
mA
VTXDL = 0 V; IDLIN = ILIN = 0 mA
VBAT = 14 V
LIN Active mode (dominant)
10
STBCL = 0; MC = 1x; VBAT = 28 V
VTXDL= 0 V; IDLIN = ILIN = 0 mA
Vth(det)pon
Vth(det)poff
Vhys(det)pon
Vuvd(LIN)
power-on detection
threshold voltage
4.5
4.25
200
5
-
-
-
-
-
-
-
5.5
4.5
-
V
power-off detection
threshold voltage
V
power-on detection
hysteresis voltage
mV
V
LIN undervoltage detection
voltage
5.3
5.5
300
7.5
Vuvr(LIN)
LIN undervoltage recovery
voltage
5
V
Vhys(uvd)LIN
Vuvd(ctrl)Iext
LIN undervoltage detection
hysteresis voltage
25
mV
V
external current control
undervoltage detection
voltage
5.9
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
33 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 10. Static characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Voltage source; pin V1
VO
output voltage
VO(V1)nom = 5 V; VBAT = 5.5 V to 28 V
IV1 = −200 mA to −5 mA; CLIN ≥ 560 pF
VO(V1)nom = 5 V; VBAT = 5.5 V to 28 V
4.9
5
5.1
V
4.85
4.75
4.5
5
5.15
5.1
V
I
V1 = −200 mA to −5 mA; CLIN ≥ 220 pF
VO(V1)nom = 5 V; VBAT = 5.5 V to 28 V
V1 = −250 mA to −200 mA
5
V
I
VO(V1)nom = 5 V; VBAT = 5.5 V to 5.75 V
5
5.1
V
IV1 = −250 mA to −5 mA
150 °C < Tvj < 200 °C
VO(V1)nom = 5 V; VBAT = 5.75 V to 28 V
4.85
5
5.1
V
I
V1 = −250 mA to −5 mA
150 °C < Tvj < 200 °C
VO(V1)nom = 3.3 V; VBAT = 4.5 V to 28 V
3.234 3.3
3.201 3.3
3.366
3.399
3.366
V
V
V
I
V1 = −250 mA to −5 mA; CLIN ≥ 560 pF
VO(V1)nom = 3.3 V; VBAT = 4.5 V to 28 V
V1 = −250 mA to −5 mA; CLIN ≥ 220 pF
VO(V1)nom = 3.3 V; VBAT = 4.5 V to 28 V
V1 = −250 mA to −5 mA
I
2.97
-
3.3
-
I
150 °C < Tvj < 200 °C
R(BAT-V1)
resistance between pin BAT VO(V1)nom = 5 V; VBAT = 4.5 V to 5.5 V
3
Ω
and pin V1
IV1 = −250 mA to −5 mA
regulator in saturation
Vuvd
undervoltage detection
voltage
90 %; VO(V1)nom = 5 V; RTHC = 0
90 %; VO(V1)nom = 3.3 V; RTHC = 0
70 %; VO(V1)nom = 5 V; RTHC = 1
90 %; VO(V1)nom = 5 V
4.5
-
-
-
-
-
-
4.75
3.135
3.75
4.9
V
2.97
3.5
V
V
Vuvr
undervoltage recovery
voltage
4.56
3.025
−600
V
90 %; VO(V1)nom = 3.3 V
3.234
−250
V
IO(sc)
short-circuit output current
IVEXCC = 0 mA
mA
Load regulation
ΔVV1
voltage variation on pin V1
as a function of load current variation
-
-
25
mV
VBAT = 5.75 V to 28 V
IV1 = −250 mA to −5 mA
Line regulation
ΔVV1
voltage variation on pin V1
as a function of supply voltage variation
VBAT = 5.5 V to 28 V; IV1 = −30 mA
-
-
25
8
mV
mA
PNP base; pin VEXCTRL
IO(sc)
short-circuit output current
VVEXCTRL ≥ 4.5 V; VBAT = 6 V to 28 V
3.5
5.8
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
34 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 10. Static characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Ith(act)PNP
PNP activation threshold
current
load current increasing; external PNP
transistor connected - see Section 6.6.2
PDC 0
74
74
44
44
130
85
191
99
mA
mA
mA
mA
PDC 0; Tvj = 150 °C
PDC 1
76
114
59
PDC 1; Tvj = 150 °C
50
Ith(deact)PNP
PNP deactivation threshold load current falling; external PNP
current
transistor connected - see Section 6.6.2
PDC 0
40
44
11
12
76
50
22
15
120
59
mA
mA
mA
mA
PDC 0; Tvj = 150 °C
PDC 1
36
PDC 1; Tvj = 150 °C
18
PNP collector; pin VEXCC
Vth(act)Ilim current limiting activation
threshold voltage
measured across resistor connected
between pins VEXCC and V1 (see
Section 6.6.2)
240
-
330
mV
2.97 V ≤ VV1 ≤ 5.5 V
6 V < VBAT < 28 V
Voltage source; pin V2
VO
output voltage
VBAT = 5.5 V to 28 V
IV2 = −100 mA to 0 mA
4.75
4.75
-
5
5
-
5.25
5.25
60
V
VBAT = 6 V to 28 V
IV2 = −120 mA to 0 mA
V
ΔVV2
voltage variation on pin V2
as a function of supply voltage variation
VBAT = 5.5 V to 28 V
mV
IV2 = −10 mA
as a function of load current variation;
6 V < VBAT < 28 V
-
-
80
mV
IV2 = −100 mA to −5 mA
Vuvd
undervoltage detection
voltage
4.5
-
-
-
-
4.70
4.75
80
V
Vuvr
undervoltage recovery
voltage
4.55
20
V
Vuvhys
undervoltage hysteresis
voltage
mV
mA
IO(sc)
short-circuit output current
VV2 = 0 V to 5.5 V
−250
−100
Serial peripheral interface inputs; pins SDI, SCK and SCSN
Vth(sw) switching threshold voltage VV1 = 2.97 V to 5.5 V
Vhys(i)
0.3VV1
100
-
0.7VV1
900
V
input hysteresis voltage
VV1 = 2.97 V to 5.5 V
-
mV
kΩ
Rpd(SCK)
pull-down resistance on pin
SCK
50
130
400
Rpu(SCSN)
pull-up resistance on pin
SCSN
50
130
400
kΩ
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
35 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 10. Static characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
ILI(SDI)
input leakage current on pin
SDI
−5
-
+5
μA
Serial peripheral interface data output; pin SDO
IOH
IOL
ILO
HIGH-level output current
LOW-level output current
output leakage current
VSCSN = 0 V; VO = VV1 − 0.4 V
VV1 = 2.97 V to 5.5 V
−30
1.6
−5
-
-
-
−1.6
30
5
mA
mA
μA
VSCSN = 0 V; VO = 0.4 V
VV1 = 2.97 V to 5.5 V
VSCSN = VV1; VO = 0 V to VV1
VV1 = 2.97 V to 5.5 V
Reset output with clamping detection; pin RSTN
IOH
HIGH-level output current
VRSTN = 0.8VV1
VV1 = 2.97 V to 5.5 V
−1500
-
-
−100
μA
IOL
LOW-level output current
strong; VRSTN = 0.2VV1
VV1 = 2.97 V to 5.5 V
−40 °C < Tvj < 200 °C
4.9
40
mA
weak; VRSTN = 0.8VV1
VV1 = 2.97 V to 5.5 V
−40 °C < Tvj < 200 °C
200
-
-
-
-
540
μA
V
VOL
LOW-level output voltage
HIGH-level output voltage
VV1 = 1 V to 5.5 V
pull-up resistor to VV1 ≥ 900 Ω
−40 °C < Tvj < 200 °C; VBAT < 28 V
0
0.2VV1
0.5
VV1 = 2.975 V to 5.5 V
pull-up resistor to V1 ≥ 900 Ω;
−40 °C < Tvj < 200 °C
0
V
VOH
-40 °C < Tvj < 200 °C
0.8VV1
VV1
0.3
+
V
Vth(sw)
Vhys(i)
Interrupt output; pin INTN
switching threshold voltage VV1 = 2.97 V to 5.5 V
0.3VV1
100
-
-
0.7VV1
900
V
input hysteresis voltage
VV1 = 2.97 V to 5.5 V
mV
IOL
LOW-level output current
VOL = 0.4 V
1.6
-
-
15
mA
mA
Enable output; pin EN
IOH
HIGH-level output current
VOH = VV1 − 0. 4 V
−20
−1.6
VV1 = 2.97 V to 5.5 V
IOL
LOW-level output current
LOW-level output voltage
VOL = 0.4 V; VV1 = 2.97 V to 5.5 V
1.6
-
-
-
20
mA
V
VOL
IOL = 20 μA; VV1 = 1.5 V
0.4
Watchdog off input; pin WDOFF
Vth(sw)
Vhys(i)
Rpupd
switching threshold voltage VV1 = 2.97 V to 5.5 V
0.3VV1
100
5
-
0.7VV1
900
V
input hysteresis voltage
VV1 = 2.97 V to 5.5 V
-
mV
kΩ
pull-up/pull-down resistance VV1 = 2.97 V to 5.5 V
10
20
Wake input; pin WAKE1, WAKE2
Vth(sw)
Vhys(i)
Ipu
switching threshold voltage
2
-
-
-
3.75
1000
0
V
input hysteresis voltage
pull-up current
100
−2
mV
μA
VWAKE = 0 V for t < twake
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
36 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 10. Static characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Ipd
pull-down current
VWAKE = VBAT for t < twake
0
-
2
μA
Limp home output; pin LIMP
IO output current
VLIMP = 0.4 V; LHC = 1
Tvj = −40 °C to 200 °C
0.8
1
-
-
8
7
mA
mA
Wake bias output; pin WBIAS
IO output current
CAN transmit data input; pin TXDC
VWBIAS = 1.4 V
Vth(sw)
Vhys(i)
Rpu
switching threshold voltage VV1 = 2.97 V to 5.5 V
0.3VV1
100
4
-
0.7VV1
900
V
input hysteresis voltage
pull-up resistance
VV1 = 2.97 V to 5.5 V
-
mV
kΩ
12
25
CAN receive data output; pin RXDC
IOH
HIGH-level output current
CAN Active mode
−20
-
−1.5
mA
VRXDC = VV1 − 0.4 V
IOL
LOW-level output current
pull-up resistance
VRXDC = 0.4 V
1.6
4
-
20
25
mA
Rpu
MC = 00; Standby mode
12
kΩ
High-speed CAN bus lines; pins CANH and CANL
VO(dom)
dominant output voltage
CAN Active mode
VV2 = 4.5 V to 5.5 V; VTXDC = 0 V
R(CANH-CANL) = 60 Ω
pin CANH
pin CANL
2.75
0.5
3.5
1.5
-
4.5
V
2.25
400
V
Vdom(TX)sym
VO(dif)bus
transmitter dominant voltage Vdom(TX)sym = VV2 − VCANH − VCANL
−400
mV
symmetry
R(CANH-CANL) = 60 Ω
bus differential output
voltage
CAN Active mode (dominant)
VV2 = 4.75 V to 5.25 V; VTXDC = 0 V
R(CANH-CANL) = 45 Ω to 65 Ω
1.5
−50
2
-
3.0
+50
3
V
CAN Active mode (recessive)
0
mV
V
VV2 = 4.5 V to 5.5 V; VTXDC = VV1
R(CANH-CANL) = no load
VO(rec)
recessive output voltage
CAN Active mode; VV2 = 4.5 V to 5.5 V
VTXDC = VV1
0.5VV2
R(CANH-CANL) = no load
CAN Lowpower/Off mode
R(CANH-CANL) = no load
−0.1
-
+0.1
V
IO(dom)
dominant output current
recessive output current
CAN Active mode
VTXDC = 0 V; VV2 = 5 V
pin CANH; VCANH = 0 V
pin CANL; VCANL = 40 V
−100
40
−70
70
-
−40
100
3
mA
mA
mA
IO(rec)
VCANL = VCANH = −27 V to +32 V
−3
VTXDC = VV1; VV2 = 4.5 V to 5.5 V
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
37 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 10. Static characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Vth(RX)dif
differential receiver
threshold voltage
CAN Active mode
0.5
0.7
0.9
V
VV2 = 4.5 V to 5.5 V
−30 V < VCANH < +30 V
−30 V < VCANL < +30 V
CAN Lowpower mode
−12 V < VCANH < +12 V
−12 V < VCANL < +12 V
0.4
40
0.7
1.15
400
V
Vhys(RX)dif
differential receiver
hysteresis voltage
CAN Active mode
120
mV
VV2 = 4.5 V to 5.5 V
−30 V < VCANH < +30 V
−30 V < VCANL < +30 V
Ri(cm)
ΔRi
common-mode input
resistance
CAN Active mode; VV2 = 5 V
VCANH = VCANL = 5 V
9
15
-
28
+1
52
20
kΩ
%
input resistance deviation
CAN Active mode; VV2 = 5 V
VCANH = VCANL = 5 V
−1
19
-
Ri(dif)
Ci(cm)
differential input resistance CAN Active mode; VV2 = 5.5 V
30
-
kΩ
pF
VCANH = VCANL = −35 V to +35 V
common-mode input
capacitance
CAN Active mode; not tested
Ci(dif)
ILI
differential input capacitance CAN Active mode; not tested
-
-
-
10
+5
pF
input leakage current
VBAT = 0 V; VV2 = 0 V
VCANH = VCANL = 5 V
−5
μA
CAN bus common mode stabilization output; pin SPLIT
VO
output voltage
leakage current
CAN Active mode
VV2 = 4.5 V to 5.5 V
ISPLIT = −500 μA to 500 μA
0.3VV2 0.5VV2 0.7VV2
V
CAN Active mode
0.45 × 0.5 ×
0.55 ×
VV2
V
VV2 = 4.5 V to 5.5 V; RL ≥ 1 MΩ
VV2
VV2
IL
CAN Lowpower/Off mode or Active
mode with VV2 < 4.5 V
−5
-
+5
μA
VSPLIT = −30 V to + 30 V
LIN transmit data input; pin TXDL
Vth(sw)
Vhys(i)
Rpu
switching threshold voltage VV1 = 2.97 V to 5.5 V
0.3VV1
100
4
-
0.7VV1
900
V
input hysteresis voltage
pull-up resistance
VV1 = 2.97 V to 5.5 V
-
mV
kΩ
12
25
LIN receive data output; pin RXDL
IOH
HIGH-level output current
LIN Active mode
−20
-
−1.5
mA
VRXDL = VV1 − 0.4 V
IOL
LOW-level output current
pull-up resistance
VRXDL= 0.4 V
1.6
4
-
20
25
mA
Rpu
MC = 00; Standby mode
12
kΩ
LIN bus line; pin LIN
IBUS_LIM
current limitation for driver
dominant state
LIN Active mode
VBAT = VLIN = 18 V
VTXDL = 0 V
40
-
100
mA
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
38 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 10. Static characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
[1]
IBUS_PAS_rec
receiver recessive input
leakage current
VLIN = 28 V; VBAT = 5.5 V; VTXDL = VV1
-
-
2
μA
IBUS_PAS_dom receiver dominant input
leakage current including
pull-up resistor
VTXDL = VV1; VLIN = 0 V; VBAT = 14 V
−10
-
+10
μA
IL(log)
loss of ground leakage
current
VBAT = VGND = 28 V; VLIN = 0 V
VBAT = 0 V; VLIN = 28 V
VBAT = 5.5 V to 18 V
−100
-
-
-
-
10
μA
μA
V
[1]
IL(lob)
loss of battery leakage
current
-
2
Vrec(RX)
receiver recessive voltage
0.6 ×
VBAT
-
Vdom(RX)
receiver dominant voltage
VBAT = 5.5 V to 18 V
-
0.4VBAT
V
V
Vth(cntr)RX
receiver center threshold
voltage
Vth(cntr)RX = (Vth(rec)RX + Vth(dom)RX)/2
VBAT = 5.5 V to 18 V; LIN Active mode
0.475 0.5 ×
× VBAT VBAT
0.525 ×
VBAT
Vth(hys)RX
receiver hysteresis threshold Vth(hys)RX = Vth(rec)RX − Vth(dom)RX
0.05 × 0.15 × 0.175 ×
V
voltage
VBAT = 5.5 V to 18 V; LIN Active mode
VBAT
VBAT
VBAT
Cext
external capacitance
dominant output voltage
on pin LIN
-
-
-
-
30
pF
V
VO(dom)
VTXDL = 0 V; VBAT = 7 V
LIN Active mode
1.4
V
TXDL = 0 V; VBAT = 18 V
-
-
2.0
1
V
V
LIN Active mode
LIN bus termination; pin DLIN
ΔV(DLIN-BAT)
voltage difference between 5 mA < IDLIN < 20 mA
pin DLIN and pin BAT
0.4
0.65
Temperature protection
Tth(act)otp overtemperature protection
165
126
180
138
200
150
°C
°C
activation threshold
temperature
Tth(rel)otp
overtemperature protection
release threshold
temperature
[1] Guaranteed by design.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
39 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
10. Dynamic characteristics
Table 11. Dynamic characteristics
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH- CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ Max
Unit
Voltage source; pin V1
td(uvd)
undervoltage detection
delay time
VV1 falling; dVV1/dt = 0.1 V/μs
7
-
-
23
μs
tdet(CL)L
LOW-level clamping
detection time
VV1 < 0.9VO(V1)nom; V1 active
95
140
ms
Voltage source; pin V2
td(uvd) undervoltage detection
delay time
Serial peripheral interface timing; pins SCSN, SCK, SDI and SDO
VV2 falling, dVV2/dt = 0.1 V/us
7
-
23
μs
tcy(clk)
clock cycle time
VV1 = 2.97 V to 5.5 V
320
110
-
-
-
-
ns
ns
tSPILEAD
SPI enable lead time
VV1 = 2.97 V to 5.5 V; clock is LOW
when SPI select falls
tSPILAG
SPI enable lag time
VV1 = 2.97 V to 5.5 V; clock is LOW
when SPI select rises
140
-
-
ns
tclk(H)
tclk(L)
tsu(D)
th(D)
clock HIGH time
VV1 = 2.97 V to 5.5 V
VV1 = 2.97 V to 5.5 V
VV1 = 2.97 V to 5.5 V
VV1 = 2.97 V to 5.5 V
160
160
0
-
-
-
-
-
-
ns
ns
ns
ns
ns
clock LOW time
-
data input set-up time
data input hold time
data output valid time
-
80
-
-
tv(Q)
pin SDO; VV1 = 2.97 V to 5.5 V
CL = 100 pF
110
tWH(S)
chip select pulse width HIGH VV1 = 2.97 V to 5.5 V
20
-
-
ns
Reset output; pin RSTN
tw(rst)
reset pulse width
long; Ipu(RSTN) < 100 μA; no pull-up
short; Rpu(RSTN) = 900 Ω to 1100 Ω
20
3.6
95
-
-
-
25
5
ms
ms
ms
tdet(CL)L
tfltr
LOW-level clamping
detection time
RSTN driven HIGH internally but RSTN
remains LOW
140
filter time
7
-
-
18
μs
Watchdog off input; pin WDOFF
tfltr filter time
Wake input; pin WAKE1, WAKE2
0.9
2.3
ms
twake
td(po)
wake-up time
10
-
-
40
μs
μs
power-on delay time
113
278
CAN transceiver timing; pins CANH, CANL, TXDC and RXDC
td(TXDCH-RXDCH) delay time from TXDC HIGH 50 % VTXDC to 50 % VRXDC
60
-
235
ns
to RXDC HIGH
VV2 = 4.5 V to 5.5 V
R(CANH-CANL) = 60 Ω
C(CANH-CANL) = 100 pF; CRXDC = 15 pF
fTXDC = 250 kHz
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
40 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 11. Dynamic characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH- CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ Max
Unit
td(TXDCL-RXDCL) delay time from TXDC LOW 50 % VTXDC to 50 % VRXDC
60
-
235
ns
to RXDC LOW
VV2 = 4.5 V to 5.5 V
R(CANH-CANL) = 60 Ω
C(CANH-CANL) = 100 pF; CRXDC = 15 pF
fTXDC = 250 kHz
td(TXDC-busdom)
td(TXDC-busrec)
td(busdom-RXDC)
delay time from TXDC to
bus dominant
VV2 = 4.5 V to 5. 5 V
-
-
-
70
90
75
-
-
-
ns
ns
ns
R(CANH-CANL) = 60 Ω
C(CANH-CANL) = 100 pF
delay time from TXDC to
bus recessive
VV2 = 4.5 V to 5.5 V
R(CANH-CANL) = 60 Ω
C(CANH-CANL) = 100 pF
delay time from bus
dominant to RXDC
VV2 = 4.5 V to 5.5 V
R(CANH-CANL) = 60 Ω
C(CANH-CANL) = 100 pF
CRXDC = 15 pF
td(busrec-RXDC)
delay time from bus
recessive to RXDC
VV2 = 4.5 V to 5.5 V
R(CANH-CANL) = 60 Ω
C(CANH-CANL) = 100 pF
CRXDC = 15 pF
-
95
-
-
ns
twake(busdom)min minimum bus dominant
wake-up time
first pulse (after first recessive) for
wake-up on pins CANH and CANL
Sleep mode
0.5
3
μs
second pulse for wake-up on pins
CANH and CANL
0.5
0.5
0.5
0.4
1.8
-
-
-
-
-
3
μs
μs
μs
ms
ms
twake(busrec)min
minimum bus recessive
wake-up time
first pulse for wake-up on pins CANH
and CANL; Sleep mode
3
second pulse (after first dominant) for
wake-up on pins CANH and CANL
3
tto(wake)
wake-up time-out time
between wake-up and confirm
messages; Sleep mode
1.2
4.5
tto(dom)TXDC
TXDC dominant time-out
time
CAN online; VV2 = 4.5 V to 5.5 V
VTXDC = 0 V
LIN transceiver; pins LIN, TXDL, RXDL
[1]
[2]
δ1
duty cycle 1
V
th(rec)RX(max) = 0.744VBAT
Vth(dom)RX(max) = 0.581VBAT; tbit = 50 μs
BAT = 7 V to 18 V; LSC = 0
0.396
-
-
-
-
-
V
[1]
[2]
Vth(rec)RX(max) = 0.76VBAT
Vth(dom)RX(max) = 0.593VBAT; tbit = 50 μs
VBAT = 5.5 V to 7 V; LSC = 0
0.396
-
[2]
[3]
δ2
duty cycle 2
V
th(rec)RX(min) = 0.422VBAT
-
-
0.581
0.581
Vth(dom)RX(min) = 0.284VBAT; tbit = 50 μs
VBAT = 7.6 V to 18 V; LSC = 0
[2]
[3]
V
th(rec)RX(min) = 0.41VBAT
Vth(dom)RX(min) = 0.275VBAT; tbit = 50 μs
VBAT = 6.1 V to 7.6 V; LSC = 0
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
41 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Table 11. Dynamic characteristics …continued
Tvj = −40 °C to +150 °C; VBAT = 4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH- CANL) = 45 Ω to 65 Ω; all voltages
are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise
specified.
Symbol
Parameter
Conditions
Min
Typ Max
Unit
[1]
[2]
δ3
duty cycle 3
Vth(rec)RX(max) = 0.778VBAT
Vth(dom)RX(max) = 0.616VBAT
tbit = 96 μs; VBAT = 7 V to 18 V; LSC = 1
0.417
-
-
-
-
-
[1]
[2]
V
V
th(rec)RX(max) = 0.797VBAT
th(dom)RX(max) = 0.630VBAT
0.417
-
tbit = 96 μs; VBAT = 5.5 V to 7 V; LSC = 1
[2]
[3]
δ4
duty cycle 4
V
V
V
th(rec)RX(min) = 0.389VBAT
th(dom)RX(min) = 0.251VBAT; tbit = 96 μs
BAT = 7.6 V to 18 V; LSC = 1
-
-
0.590
0.590
[2]
[3]
Vth(rec)RX(min) = 0.378VBAT
Vth(dom)RX(min) = 0.242VBAT; tbit = 96 μs
VBAT = 6.1 V to 7.6V; LSC = 1
tPD(RX)r
rising receiver propagation
delay
VBAT = 5.5 V to 18 V; RRXDL = 2.4 kΩ
CRXDL = 20 pF
-
-
-
-
-
-
6
μs
μs
μs
μs
ms
tPD(RX)f
falling receiver propagation VBAT = 5.5 V to 18 V; RRXDL = 2.4 kΩ
delay
-
6
CRXDL = 20 pF
[4]
tPD(RX)sym
receiver propagation delay
symmetry
VBAT = 5.5 V to 18 V; RRXDL = 2.4 kΩ
CRXDL = 20 pF
−2
28
20
+2
104
80
twake(busdom)min minimum bus dominant
wake-up time
tto(dom)TXDL
TXDL dominant time-out
time
LIN online mode; VTXDL = 0 V
Wake bias output; pin WBIAS
tWBIASL
tcy
WBIAS LOW time
cycle time
227
-
-
-
278
μs
WBC = 1
WBC = 0
58.1
14.5
71.2
17.8
ms
ms
Watchdog
[5]
[7]
ttrig(wd)1
watchdog trigger time 1
watchdog trigger time 2
Normal mode
watchdog Window mode only
0.45 ×
-
-
0.555 × ms
NWP[6]
NWP[6]
ttrig(wd)2
Normal, Standby and Sleep modes
watchdog Window mode only
0.9 ×
1.11 ×
ms
NWP[6]
NWP[6]
Oscillator
fosc
oscillator frequency
460.8 512 563.2
kHz
tbus(rec)(min)
-------------------------------
[1] δ1, δ3 =
. Variable tbus(rec)(min) is illustrated in the LIN timing diagram in Figure 18.
2 × tbit
[2] Bus load conditions are: CL = 1 nF and RL = 1 kΩ; CL = 6.8 nF and RL = 660 Ω; CL = 10 nF and RL = 500 Ω.
tbus(rec)(max)
-------------------------------
[3] δ2, δ4 =
. Variable tbus(rec)(max) is illustrated in the LIN timing diagram in Figure 18.
2 × tbit
[4] tPD(RX)sym = tPD(RX)r − tPD(RX)f
.
[5] A system reset will be performed if the watchdog is in Window mode and is triggered less than ttrig(wd)1 after the start of the watchdog
period (or in the first half of the watchdog period).
[6] The nominal watchdog period is programmed via the NWP control bits in the WD_and_Status register (see Table 4); valid in watchdog
Window mode only.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
42 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
[7] The watchdog will be reset if it is in window mode and is triggered at least ttrig(wd)1, but not more than ttrig(wd)2, after the start of the
watchdog period (or in the second half of the watchdog period). A system reset will be performed if the watchdog is triggered more than
t
trig(wd)2 after the start of the watchdog period (watchdog overflows).
BAT
RXDC
CANH
CANL
R
− R
C
− C
CANH CANL
CANH
CANL
SBC
C
RXDC
TXDC
GND
015aaa079
Fig 15. Timing test circuit for CAN transceiver
HIGH
LOW
TXDC
CANH
CANL
dominant
0.9 V
0.5 V
V
O(dif)bus
recessive
HIGH
RXDC
LOW
t
t
d(TXDC-busrec)
d(TXDC-busdom)
t
t
d(busrec-RXDC)
d(busdom-RXDC)
t
t
d(TXDCH-RXDCH)
d(TXDCL-RXDCL)
015aaa151
Fig 16. CAN transceiver timing diagram
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
43 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
BAT
RXDL
TXDL
DLIN
R
LIN
SBC
C
RXDL
LIN
C
LIN
GND
015aaa128
Fig 17. Timing test circuit for LIN transceiver
t
t
t
bit
bit
bit
V
TXDL
t
t
bus(rec)(min)
bus(dom)(max)
V
BAT
V
V
th(rec)RX(max)
thresholds of
receiving node A
th(dom)RX(max)
LIN bus signal
V
V
th(rec)RX(min)
thresholds of
receiving node B
th(dom)RX(min)
t
t
bus(rec)(max)
bus(dom)(min)
output of receiving
node A
V
V
RXDL
t
t
PD(RX)r
PD(RX)f
output of receiving
node B
RXDL
t
t
PD(RX)f
PD(RX)r
015aaa133
Fig 18. LIN transceiver timing diagram
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
44 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
SCS
SCK
t
t
WH(S)
t
T
SPILAG
SPILEAD
cy(clk)
t
t
clk(L)
clk(H)
t
t
h(D)
su(D)
SDI
MSB
LSB
X
X
t
v(Q)
floating
floating
SDO
X
MSB
LSB
015aaa045
Fig 19. SPI timing diagram
11. Test information
11.1 Quality information
This product has been qualified in accordance with the Automotive Electronics Council
(AEC) standard Q100 - Failure mechanism based stress test qualification for integrated
circuits, and is suitable for use in automotive applications.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
45 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
12. Package outline
HTSSOP32: plastic thermal enhanced thin shrink small outline package; 32 leads;
body width 6.1 mm; lead pitch 0.65 mm; exposed die pad
SOT549-1
E
A
D
X
c
H
v
M
A
y
exposed die pad side
E
D
h
Z
32
17
A
(A )
3
2
E
A
h
A
1
pin 1 index
θ
L
p
L
detail X
1
16
w
M
b
e
p
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions).
A
(1)
(2)
UNIT
A
A
A
b
c
D
D
E
E
e
H
L
L
p
v
w
y
Z
θ
1
2
3
p
h
h
E
max.
8o
0o
0.15 0.95
0.05 0.85
0.30 0.20 11.1
0.19 0.09 10.9
5.1
4.9
6.2
6.0
3.6
3.4
8.3
7.9
0.75
0.50
0.78
0.48
mm
1.1
0.65
1
0.2
0.25
0.1
0.1
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
03-04-07
05-11-02
SOT549-1
MO-153
Fig 20. Package outline SOT549-1 (HTSSOP32)
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
46 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
13. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
13.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
13.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
• Board specifications, including the board finish, solder masks and vias
• Package footprints, including solder thieves and orientation
• The moisture sensitivity level of the packages
• Package placement
• Inspection and repair
• Lead-free soldering versus SnPb soldering
13.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
47 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
13.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 21) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 12 and 13
Table 12. SnPb eutectic process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
235
≥ 350
220
< 2.5
≥ 2.5
220
220
Table 13. Lead-free process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
260
350 to 2000
> 2000
260
< 1.6
260
250
245
1.6 to 2.5
> 2.5
260
245
250
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 21.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
48 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 21. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
49 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
14. Revision history
Table 14. Revision history
Document ID
UJA1075_2
Release date
20100527
Data sheet status
Change notice
Supersedes
Product data sheet
-
UJA1075_1
Modifications:
• Template upgraded to Rev. 2.11 including revised legal information
• Figure 16, Figure 18: revised
• Table 4: bit 7: WOS revised
• Table 8: revised values/conditions - VESD, IR(V1-BAT)
• Table 9: added
• Table 10: revised parameter values/conditions - Vth(cntr)RX, Vth(hys)RX, VOL for RSTN pin,
IO for LIMP pin; R(BAT-V1); Vuvr for pin V1
• Table 11: revised parameter values/conditions - tdet(CL)L for RSTN pin
• Section 6.7.1.2, Section 6.8.1.2, Table 11: parameters renamed to twake(busdom)min
,
twake(busrec)min
UJA1075_1
20091125
Product data sheet
-
-
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
50 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
15. Legal information
15.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
suitable for use in medical, military, aircraft, space or life support equipment,
15.2 Definitions
nor in applications where failure or malfunction of an NXP Semiconductors
product can reasonably be expected to result in personal injury, death or
severe property or environmental damage. NXP Semiconductors accepts no
liability for inclusion and/or use of NXP Semiconductors products in such
equipment or applications and therefore such inclusion and/or use is at the
customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
15.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use in automotive applications — This NXP
Semiconductors product has been qualified for use in automotive
applications. The product is not designed, authorized or warranted to be
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
51 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
15.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
16. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
UJA1075_2
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 27 May 2010
52 of 53
UJA1075
NXP Semiconductors
High-speed CAN/LIN core system basis chip
17. Contents
1
General description. . . . . . . . . . . . . . . . . . . . . . 1
6.7.3.1
6.7.3.2
6.8
TXDC dominant time-out function . . . . . . . . . 24
Pull-up on TXDC pin . . . . . . . . . . . . . . . . . . . 24
LIN transceiver. . . . . . . . . . . . . . . . . . . . . . . . 24
LIN operating modes . . . . . . . . . . . . . . . . . . . 25
Active mode . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Lowpower/Off modes. . . . . . . . . . . . . . . . . . . 25
Fail-safe features . . . . . . . . . . . . . . . . . . . . . . 25
General fail-safe features. . . . . . . . . . . . . . . . 25
TXDL dominant time-out function . . . . . . . . . 25
Local wake-up input. . . . . . . . . . . . . . . . . . . . 26
Interrupt output. . . . . . . . . . . . . . . . . . . . . . . . 27
Temperature protection . . . . . . . . . . . . . . . . . 27
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 2
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CAN transceiver . . . . . . . . . . . . . . . . . . . . . . . . 2
LIN transceiver . . . . . . . . . . . . . . . . . . . . . . . . . 2
Power management . . . . . . . . . . . . . . . . . . . . . 2
Control and Diagnostic features . . . . . . . . . . . . 3
Voltage regulators. . . . . . . . . . . . . . . . . . . . . . . 3
2.1
2.2
2.3
2.4
2.5
2.6
6.8.1
6.8.1.1
6.8.1.2
6.8.2
6.8.2.1
6.8.2.2
6.9
3
4
Ordering information. . . . . . . . . . . . . . . . . . . . . 4
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6.10
6.11
5
5.1
5.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 5
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
7
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 28
Thermal characteristics . . . . . . . . . . . . . . . . . 30
Static characteristics . . . . . . . . . . . . . . . . . . . 32
Dynamic characteristics. . . . . . . . . . . . . . . . . 40
Test information . . . . . . . . . . . . . . . . . . . . . . . 45
Quality information. . . . . . . . . . . . . . . . . . . . . 45
Package outline. . . . . . . . . . . . . . . . . . . . . . . . 46
8
6
6.1
Functional description . . . . . . . . . . . . . . . . . . . 6
System Controller . . . . . . . . . . . . . . . . . . . . . . 7
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Off mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . 9
Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Overtemp mode . . . . . . . . . . . . . . . . . . . . . . . 10
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Register map . . . . . . . . . . . . . . . . . . . . . . . . . 11
WD_and_Status register. . . . . . . . . . . . . . . . . 12
Mode_Control register . . . . . . . . . . . . . . . . . . 13
Int_Control register. . . . . . . . . . . . . . . . . . . . . 14
Int_Status register. . . . . . . . . . . . . . . . . . . . . . 16
On-chip oscillator . . . . . . . . . . . . . . . . . . . . . . 16
Watchdog (UJA1075/xx/WD versions) . . . . . . 17
Watchdog Window behavior. . . . . . . . . . . . . . 17
Watchdog Timeout behavior. . . . . . . . . . . . . . 17
Watchdog Off behavior. . . . . . . . . . . . . . . . . . 18
System reset. . . . . . . . . . . . . . . . . . . . . . . . . . 18
RSTN pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
EN output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LIMP output . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power supplies . . . . . . . . . . . . . . . . . . . . . . . . 20
Battery pin (BAT) . . . . . . . . . . . . . . . . . . . . . . 20
Voltage regulator V1 . . . . . . . . . . . . . . . . . . . . 20
Voltage regulator V2 . . . . . . . . . . . . . . . . . . . . 22
CAN transceiver . . . . . . . . . . . . . . . . . . . . . . . 22
CAN operating modes . . . . . . . . . . . . . . . . . . 22
Active mode . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Lowpower/Off modes . . . . . . . . . . . . . . . . . . . 23
Split circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Fail-safe features . . . . . . . . . . . . . . . . . . . . . . 24
9
10
11
11.1
12
6.1.1
6.1.2
6.1.3
6.1.4
6.1.5
6.1.6
6.2
6.2.1
6.2.2
6.2.3
6.2.4
6.2.5
6.2.6
6.3
13
Soldering of SMD packages. . . . . . . . . . . . . . 47
Introduction to soldering. . . . . . . . . . . . . . . . . 47
Wave and reflow soldering. . . . . . . . . . . . . . . 47
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . 47
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . 48
13.1
13.2
13.3
13.4
14
Revision history . . . . . . . . . . . . . . . . . . . . . . . 50
15
Legal information . . . . . . . . . . . . . . . . . . . . . . 51
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 51
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 52
15.1
15.2
15.3
15.4
6.4
6.4.1
6.4.2
6.4.3
6.5
6.5.1
6.5.2
6.5.3
6.6
6.6.1
6.6.2
6.6.3
6.7
6.7.1
6.7.1.1
6.7.1.2
6.7.2
6.7.3
16
17
Contact information . . . . . . . . . . . . . . . . . . . . 52
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2010.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 27 May 2010
Document identifier: UJA1075_2
相关型号:
UJA1076ATW/3V3
IC 16-BIT, FLASH, MICROCONTROLLER, PDSO32, 11 X 6.10 MM, 0.65 MM PITCH, GREEN, PLASTIC, MO-153, SOT-549-1, HTSSOP-32, Microcontroller
NXP
UJA1076ATW/3V3/WD
IC 16-BIT, FLASH, MICROCONTROLLER, PDSO32, 11 X 6.10 MM, 0.65 MM PITCH, GREEN, PLASTIC, MO-153, SOT-549-1, HTSSOP-32, Microcontroller
NXP
UJA1076ATW/5V0/WD
IC 16-BIT, FLASH, MICROCONTROLLER, PDSO32, 11 X 6.10 MM, 0.65 MM PITCH, GREEN, PLASTIC, MO-153, SOT-549-1, HTSSOP-32, Microcontroller
NXP
©2020 ICPDF网 联系我们和版权申明