MSM51V16160F-50TS-K [OKI]
Fast Page DRAM, 1MX16, 50ns, CMOS, PDSO44, 0.400 INCH, PLASTIC, TSOP2-50/44;
| 型号： | MSM51V16160F-50TS-K |
| 厂家： | 
OKI ELECTRONIC COMPONETS |
| 描述： | Fast Page DRAM, 1MX16, 50ns, CMOS, PDSO44, 0.400 INCH, PLASTIC, TSOP2-50/44 动态存储器 光电二极管 |
| 文件： | 总16页 (文件大小：228K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
FEDD51V16160F-02
Issue Date: Aug. 16, 2002
OKI Semiconductor
MSM51V16160F
1,048,576-Word × 16-Bit DYNAMIC RAM : FAST PAGE MODE TYPE
DESCRIPTION
The MSM51V16160F is a 1,048,576-word × 16-bit dynamic RAM fabricated in Oki’s silicon-gate
CMOS technology. The MSM51V16160F achieves high integration, high-speed operation, and
low-power consumption because Oki manufactures the device in
a
quadruple-layer
polysilicon/double-layer metal CMOS process. The MSM51V16160F is available in a 50/44-pin plastic
TSOP.
FEATURES
· 1,048,576-word × 16-bit configuration
· Single 3.3V power supply, ±0.3V tolerance
· Input : LVTTL compatible, low input capacitance
· Output : LVTTL compatible, 3-state
· Refresh : 4096 cycles/64ms
· Fast page mode, read modify write capability
· CAS before RAS refresh, hidden refresh, RAS-only refresh capability
· Packages
50/44-pin 400mil plastic TSOP (TSOPII50/44-P-400-0.80-K) (Product : MSM51V16160F-xxTS-K)
xx indicates speed rank.
PRODUCT FAMILY
Access Time (Max.)
Power Dissipation
Cycle Time
(Min.)
Family
Operating
(Max.)
Standby
(Max.)
tRAC
tAA
tCAC
tOEA
50ns
60ns
70ns
25ns
30ns
35ns
13ns
15ns
20ns
13ns
15ns
20ns
90ns
110ns
130ns
270mW
252mW
234mW
MSM51V16160F
1.8mW
1/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
PIN CONFIGURATION (TOP VIEW)
1
2
50
49
48
47
46
45
44
43
42
41
40
VCC
VSS
DQ1
DQ2
DQ3
DQ4
VCC
DQ16
DQ15
DQ14
DQ13
VSS
3
4
5
6
7
8
9
10
11
DQ5
DQ6
DQ7
DQ8
NC
DQ12
DQ11
DQ10
DQ9
NC
15
16
17
18
19
20
21
22
23
24
36
35
34
33
32
31
30
29
28
27
26
NC
NC
WE
RAS
A11R
A10R
A0
A1
A2
A3
V
NC
LCAS
UCAS
OE
A9R
A8R
A7
A6
A5
A4
VSS
CC 25
50/44-Pin Plastic TSOP
(K Type)
Pin Name
Function
A0–A7, A8R–A11R
Address Input
Row Address Strobe
Lower Byte Column Address Strobe
Upper Byte Column Address Strobe
Data Input/Data Output
Output Enable
RAS
LCAS
UCAS
DQ1–DQ16
OE
WE
Write Enable
VCC
Power Supply (3.3V)
Ground (0V)
VSS
NC
No Connection
Note : The same power supply voltage must be provided to every VCC pin, and the same GND voltage level must
be provided to every VSS pin.
2/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
BLOCK DIAGRAM
WE
OE
Timing
RAS
Generator
I/O
Controller
LCAS
UCAS
Output
Buffers
8
8
8
I/O
Controller
DQ1-DQ8
Column
Address
Buffers
Input
Buffers
8
8
Column Decoders
Sense Amplifiers
8
I/O
Selector
Internal
Address
Counter
Refresh
Control Clock
16
16
A0-A7
Input
Buffers
8
8
8
Row
Address
Buffers
8
4
Row
Deco-
ders
12
DQ9-DQ16
Word
Drivers
Memory
Cells
A8R-A11R
Output
Buffers
8
VCC
On Chip
VBB Generator
On Chip
IVCC Generator
VSS
FUNCTION TABLE
Input Pin
DQ Pin
DQ1-DQ8
Function Mode
RAS
H
L
LCAS
UCAS
WE
*
OE
*
DQ9-DQ16
High-Z
High-Z
High-Z
DOUT
*
H
L
H
L
L
H
L
L
*
H
H
L
L
H
L
L
L
High-Z
High-Z
DOUT
Standby
Refresh
*
*
L
H
H
H
L
L
Lower Byte Read
Upper Byte Read
Word Read
L
L
High-Z
DOUT
L
L
DOUT
L
H
H
H
H
DIN
Don’t Care
DIN
Lower Byte Write
Upper Byte Write
Word Write
L
L
Don’t Care
DIN
L
L
DIN
L
H
High-Z
High-Z
* : “H” or “L”
3/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
ELECTRICAL CHARACTERISTICS
ABSOLUTE MAXIMUM RATINGS
Parameter
Voltage on Any Pin Relative to VSS
Voltage VCC Supply relative to VSS
Short Circuit Output Current
Power Dissipation
Symbol
VIN, VOUT
VCC
Value
–0.5 to VCC+ 0.5
–0.5 to 4.6
50
Unit
V
V
IOS
mA
W
PD*
1
Operating Temperature
Topr
0 to 70
°C
°C
Storage Temperature
Tstg
–55 to 150
*: Ta = 25°C
RECOMMENDED OPERATIING CONDITIONS
(Ta = 0 to 70°C)
Parameter
Symbol
VCC
VSS
Min.
3.0
Typ.
Max.
Unit
V
3.3
0
3.6
Power Supply Voltage
0
0
VCC + 0.3*1
0.8
V
Input High Voltage
Input Low Voltage
VIH
2.0
V
VIL
− 0.3*2
V
Notes: *1. The input voltage is VCC + 1.0V when the pulse width is less than 20ns (the pulse width is with respect
to the point at which VCC is applied).
*2. The input voltage is VSS − 1.0V when the pulse width is less than 20ns (the pulse width respect to the
point at which VSS is applied).
PIN CAPACITANCE
(Vcc = 3.3V ± 0.3V, Ta = 25°C, f = 1 MHz)
Parameter
Symbol
CIN1
Min.
—
Max.
5
Unit
pF
Input Capacitance (A0 – A7, A8R – A11R)
Input Capacitance
CIN2
CI/O
—
—
7
7
pF
pF
(RAS, LCAS, UCAS, WE, OE)
Output Capacitance (DQ1 - DQ16)
4/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
DC CHARACTERISTICS
(VCC = 3.3V ± 0.3V, Ta = 0 to 70°C)
MSM51V16160 MSM51V16160 MSM51V16160
F-50 F-60 F-70
Parameter
Symbol
Condition
Unit Note
Min.
Max.
Min.
Max.
Min.
Max.
Output High Voltage
Output Low Voltage
V
I
I
= −2.0mA
2.4
0
V
2.4
0
V
2.4
0
V
CC
V
V
OH
OH
OL
CC
CC
V
= 2.0mA
0.4
0.4
0.4
OL
0V ≤ V ≤ VCC + 0.3V;
I
Input Leakage
Current
I
− 10
− 10
10
− 10
− 10
10
− 10
− 10
10
µA
µA
All other pins not
under test = 0V
LI
DQ disable
Output Leakage
Current
I
10
75
10
70
10
65
LO
0V ≤ V ≤ V
O
CC
Average Power
Supply Current
RAS, CAS cycling,
= Min.
I
mA 1,2
CC1
CC2
t
RC
(Operating)
RAS, CAS = V
RAS, CAS
2
2
2
IH
Power Supply
Current
I
I
I
mA
1
0.5
0.5
0.5
(Standby)
≥ V
− 0.2V
CC
RAS cycling,
Average Power
Supply Current
CAS = V ,
IH
75
5
70
5
65
5
mA 1,2
CC3
CC5
(RAS-only Refresh)
t
= Min.
RC
RAS = V ,
IH
Power Supply
Current
CAS = V ,
mA
1
IL
(Standby)
DQ = enable
Average Power
Supply Current
RAS = cycling,
I
I
75
75
70
70
65
65
mA 1,2
mA 1,3
CC6
CC7
(CAS before RAS
Refresh)
CAS before RAS
RAS = V ,
Average Power
Supply Current
IL
CAS cycling,
(Fast Page Mode)
t
= Min.
PC
Notes: 1. ICC Max. is specified as ICC for output open condition.
2. The address can be changed once or less while RAS = VIL.
3. The address can be changed once or less while CAS = VIH.
5/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
AC CHARACTERISTICS (1/2)
(VCC = 3.3V ± 0.3V, Ta = 0 to 70°C) Note1,2,3
MSM51V16160 MSM51V16160 MSM51V16160
F-50 F-60 F-70
Parameter
Symbol
Unit Note
Min.
90
Max. Max. Max.
Min.
110
155
40
Min.
130
185
45
Random Read or Write Cycle Time
Read Modify Write Cycle Time
Fast Page Mode Cycle Time
t
ns
ns
ns
RC
t
131
35
RWC
t
PC
Fast Page Mode Read Modify Write
Cycle Time
t
76
85
100
ns
PRWC
Access Time from RAS
t
t
50
13
25
30
13
60
15
30
35
15
70
20
35
40
20
ns 4, 5, 6
RAC
CAC
Access Time from CAS
ns
ns
4, 5
4, 6
Access Time from Column Address
Access Time from CAS Precharge
Access Time from OE
t
AA
t
ns 4, 12
CPA
OEA
t
ns
ns
4
4
Output Low Impedance Time from
CAS
t
0
0
0
13
13
0
0
0
15
15
0
0
0
20
20
CLZ
OFF
OEZ
CAS to Data Output Buffer Turn-
off Delay Time
t
ns
ns
7
OE to Data Output Buffer Turn-off
Delay Time
t
7
3
Transition Time
t
1
50
64
1
50
64
1
50
64
ns
ms
ns
T
Refresh Period
t
30
50
50
13
13
40
60
60
15
15
50
70
70
20
20
REF
RAS Precharge Time
RAS Pulse Width
t
RP
t
10,000
100,000
10,000
100,000
10,000 ns
100,000 ns
RAS
RAS Pulse Width (Fast Page Mode)
RAS Hold Time
t
RASP
t
ns
ns
RSH
ROH
RAS Hold Time referenced to OE
t
CAS Precharge Time
(Fast Page Mode)
t
7
10
10
ns
14
CP
CAS Pulse Width
t
13
50
5
10,000
15
60
5
10,000
20
70
5
10,000 ns
CAS
CSH
CRP
CAS Hold Time
t
t
50
35
ns
ns
ns
ns
ns
ns
CAS to RAS Precharge Time
12
12
5
RAS Hold Time from CAS Precharge t
RAS to CAS Delay Time
30
17
12
0
35
20
15
0
40
20
15
0
RHCP
t
37
45
RCD
RAD
RAS to Column Address Delay Time
Row Address Set-up Time
t
25
30
6
t
ASR
6/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
AC CHARACTERISTICS (2/2)
(VCC = 3.3V ± 0.3V, Ta = 0 to 70°C) Note1,2,3
MSM51V16160 MSM51V16160 MSM51V16160
F-50 F-60 F-70
Parameter
Symbol
Unit Note
Min.
7
Max. Max. Max.
Min.
10
0
Min.
10
0
Row Address Hold Time
t
ns
RAH
Column Address Set-up Time
Column Address Hold Time
Column Address to RAS Lead Time
Read Command Set-up Time
Read Command Hold Time
t
0
ns
ns
ns
ns
11
11
ASC
t
7
10
30
0
15
35
0
CAH
t
25
0
RAL
RCS
RCH
t
11
t
t
0
0
0
ns 8, 11
ns
ns 9, 11
Read Command Hold Time
referenced to RAS
0
0
0
8
RRH
Write Command Set-up Time
Write Command Hold Time
Write Command Pulse Width
OE Command Hold Time
Write Command to RAS Lead Time
Write Command to CAS Lead Time
Data-in Set-up Time
t
0
0
0
15
10
20
20
20
0
WCS
t
7
10
10
15
15
15
0
ns
ns
ns
ns
ns
11
WCH
t
7
WP
t
13
13
13
0
OEH
RWL
CWL
t
t
13
t
ns 10, 11
ns 10, 11
ns
DS
Data-in Hold Time
t
7
10
15
40
55
85
60
15
20
50
65
100
70
DH
OE to Data-in Delay Time
CAS to WE Delay Time
t
13
36
48
73
53
OED
t
ns
ns
ns
ns
9
9
9
9
CWD
Column Address to WE Delay Time
RAS to WE Delay Time
t
AWD
t
RWD
CAS Precharge WE Delay Time
t
CPWD
CAS Active Delay Time from RAS
Precharge
t
5
5
5
5
5
5
ns
ns
ns
11
11
12
RPC
CSR
CHR
RAS to CAS Set-up Time
(CAS before RAS)
t
RAS to CAS Hold Time
(CAS before RAS)
t
10
10
10
7/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
Notes: 1. A start-up delay of 200µs is required after power-up, followed by a minimum of eight initialization
cycles (RAS-only refresh or CAS before RAS refresh) before proper device operation is achieved.
2. The AC characteristics assume tT = 5ns.
3. VIH (Min.) and VIL (Max.) are reference levels for measuring input timing signals. Transition times (tT)
are measured between VIH and VIL.
4. -50 is measured with a load circuit equivalent to 1 TTL load and 50pF, and -60/-70 is measured with a
load circuit equivalent to 1 TTL load and 100pF.
The output timing reference levels are VOH=2.0 and VOL=0.8V.
5. Operation within the tRCD (Max.) limit ensures that tRAC (Max.) can be met.
tRCD (Max.) is specified as a reference point only. If tRCD is greater than the specified tRCD (Max.) limit,
then the access time is controlled by tCAC
.
6. Operation within the tRAD (Max.) limit ensures that tRAC (Max.) can be met.
RAD (Max.) is specified as a reference point only. If tRAD is greater than the specified tRAD (Max.) limit,
then the access time is controlled by tAA
t
.
7. tOFF (Max.) and tOEZ (Max.) define the time at which the output achieved the open circuit condition and
are not referenced to output voltage levels.
8. tRCH or tRRH must be satisfied for a read cycle.
9. tWCS, tCWD, tRWD, tAWD and tCPWD are not restrictive operating parameters. They are included in the data
sheet as electrical characteristics only. If tWCS ≥ tWCS (Min.), then the cycle is an early write cycle and
the data out will remain open circuit (high impedance) throughout the entire cycle. If tCWD ≥ tCWD
(Min.), tRWD ≥ tRWD(Min.), tAWD ≥ tAWD (Min.) and tCPWD ≥ tCPWD (Min.), then the cycle is a read modify
write cycle and data out will contain data read from the selected cell; if neither of the above sets of
conditions is satisfied, then the condition of the data out (at access time) is indeterminate.
10. These parameters are referenced to the UCAS and LCAS, leading edges in an early write cycle, and to
the WE leading edge in an OE control write cycle, or a read modify write cycle.
11. These parameters are determined by the falling edge of either UCAS or LCAS, whichever is earlier.
12. These parameters are determined by the rising edge of either UCAS or LCAS, whichever is later.
13. tCWL should be satisfied by both UCAS and LCAS.
14. tCP is determined by the time both UCAS and LCAS are high.
8/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
TIMING CHART
Read Cycle
tRC
tRAS
VIH
RAS
tRP
VIL
tCSH
tCRP
tCRP
tRCD
tRSH
tCAS
VIH
CAS
tRAD
tASR tRAH
VIL
tRAL
tASC
tCAH
VIH
Address
VIL
Row
Column
tRCS
tRRH
VIH
WE
tAA
tRCH
VIL
tROH
tOEA
VIH
OE
VIL
tCAC
tOFF
tRAC
tOEZ
tCLZ
VOH
DQ
Valid Data-out
Open
VOL
“H” or “L”
Write Cycle (Early Write)
tRC
tRAS
VIH
RAS
tRP
tCRP
VIL
tCSH
tCRP
tRCD
tRSH
tCAS
VIH
CAS
tRAD
VIL
tRAL
tRAH
tASR
tASC
tCAH
VIH
Address
Row
Column
VIL
tCWL
tWCH
tWCS
tWP
VIH
VIL
WE
OE
DQ
tRWL
VIH
VIL
tDS
tDH
VIH
VIL
Valid Data-in
Open
“H” or “L”
9/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
Read Modify Write Cycle
tRWC
tRAS
VIH
RAS
tRP
VIL
tCSH
tCRP
tCRP
tRCD
tRSH
tCAS
VIH
CAS
tRAD
tASR tRAH
VIL
tCWL
tRWL
tASC
tCAH
VIH
VIL
Row
Colum
Address
tRCS
tCWD
tWP
tRWD
VIH
VIL
WE
OE
tAWD
tAA
tOEH
tOEA
VIH
VIL
tOED
tOEZ
tCAC
tDH
tRAC
tDS
tCLZ
VI/OH
VI/OL
Valid
Data-out
Valid
Data-in
DQ
“H” or “L”
10/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
Fast Page Mode Read Cycle
tRP
tRASP
tPC
tRHCP
VIH
RAS
VIL
tRCD
tCP
tCP
tRSH
tCAS
tCRP
tCRP
tCAS
tCAS
VIH
CAS
tRAD
tCSH
tRAH
VIL
tRAL
tCAH
tASR
Row
tASC
Column
tASC tCAH
tCA
tASC
VIH
VIL
Column
tRCS
Column
tRCS
Address
WE
tRCS
tRCH
tRCH
tRCH
VIH
VIL
tAA
tAA
tAA
tRRH
tOEA
tOEA
tOEA
VIH
VIL
OE
tRAC
tCPA
tOFF
tOEZ
tCPA
tOFF
tOFF
tCAC
tCLZ
tCAC
tCLZ
tCAC
tOEZ
tOEZ
tCLZ
VOH
VOL
Valid
Data-out
Valid
Data-out
Valid
Data-out
DQ
“H” or “L”
Fast Page Mode Write Cycle (Early Write)
tRP
tRASP
tRHPC
tPC
VIH
RAS
VIL
tCRP
tCRP
tCP
tCP
tRSH
tCAS
tRCD
tCAS
tCAS
VIH
CAS
tRAD
tRAH
VIL
tCSH
tCAH
tRAL
tCAH
tASR
tASC
tASC
tCAH
tASC
VIH
VIL
Row
Column
Column
Column
tRWL
Address
tCWL
tWCH
tWP
tCWL
tWCH
tWP
tCWL
tWCS
tWCS
tWCS
tWCH
tWP
VIH
VIL
WE
tDS
tDH
tDS
tDH
tDS
tDH
VIH
VIL
Valid *
Data-in
Valid *
Data-in
Valid *
Data-in
DQ
Note: OE = “H” or “L”
“H” or “L”
11/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
Fast Page Mode Read Modify Write Cycle
tRASP
tRP
tCSH
tPRWC
tRSH
VIH
RAS
VIL
tCP
tCP
tCR
tRCD
tCAS
tCAS
tCAH
tCAS
tCAH
VIH
VIL
CAS
tRAD
tASC
tRAH
tASR
tCAH
tCWL
tASC
tASC
tRAL
tCWL
VIH
VIL
Row
Column
Column
tRCS
Column
tRC
Address
tCWL
tRWD
tCWD
tCPWD
tCPWD
tCWD
tRWL
tCWD
tRCS
VIH
VIL
WE
tAWD
tAWD
tAWD
tWP
tWP
tWP
tDH
tCPA
tAA
tRAC
tAA
tROH
tCPA
tDH
tDS
tDH
tDS
tAA
tOEA
tOEA
tOEA
VIH
VIL
tOED
tOEZ
OE
tOED
tOEZ
tOED
tOEZ
tCAC
tCAC
tCAC
tDS
VI/OH
VI/OL
DQ
Out
Out
In
Out
In
In
tCLZ
tCLZ
tCLZ
Note: In = Valid Data-in, Out = Valid Data-out
“H” or “L”
RAS-only Refresh Cycle
tRC
tRAS
VIH
RAS
tRP
VIL
tCRP
tRPC
VIH
VIL
CAS
Address
DQ
tASR tRAH
VIH
VIL
Row
tOFF
VOH
VOL
Open
Note: WE, OE = “H” or “L”
“H” or “L”
12/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
CAS before RAS Refresh Cycle
tRC
tRP
tRAS
VIH
RAS
VIL
tRPC
tRP
tCP
tCSR
tRPC
tCHR
VIH
CAS
VIL
tOFF
VOH
VOL
DQ
Open
“H” or “L”
Note: WE, OE, Address = “H” or “L”
Hidden Refresh Read Cycle
tRC
tRC
tRAS
tRAS
VIH
RAS
VIL
tCRP
tRP
tRCD
tRSH
tRP
tCHR
VIH
CAS
tRAD
tRAH
VIL
tASR
tASC
tCAH
VIH
Address
Column
Row
VIL
tRCS
tCAC
tRAL
tRRH
VIH
VIL
WE
tAA
tROH
tOEA
tOFF
VIH
VIL
OE
tRAC
tOEZ
tCLZ
VOH
VOL
DQ
Open
Valid Data-out
“H” or “L”
13/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
Hidden Refresh Write Cycle
tRC
tRC
tRAS
tRAS
VIH
RAS
VIL
tCRP
tRP
tRSH
tRP
tRCD
tCHR
VIH
CAS
tRAD
tRAH
VIL
tRAL
tCAH
tASR
tASC
VIH
Address
Row
Column
VIL
tWCS
tWCH
VIH
VIL
WE
OE
DQ
tWP
VIH
VIL
tDS
tDH
VIH
VIL
Valid Data-in
“H” or “L”
14/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
REVISION HISTORY
Page
Previous Current
Document
No.
Date
Description
Edition
Edition
FEDD51V16160F-01
FEDD51V16160F-02
May., 2000
Aug., 2002
–
–
Final edition 1
Deleted SOJ package
1, 2
1, 2
15/16
FEDD51V16160F-02
1
Semiconductor
MSM51V16160F
NOTICE
1. The information contained herein can change without notice owing to product and/or technical improvements.
Before using the product, please make sure that the information being referred to is up-to-date.
2. The outline of action and examples for application circuits described herein have been chosen as an explanation
for the standard action and performance of the product. When planning to use the product, please ensure that
the external conditions are reflected in the actual circuit, assembly, and program designs.
3. When designing your product, please use our product below the specified maximum ratings and within the
specified operating ranges including, but not limited to, operating voltage, power dissipation, and operating
temperature.
4. Oki assumes no responsibility or liability whatsoever for any failure or unusual or
unexpected operation resulting from misuse, neglect, improper installation, repair, alteration
or accident, improper handling, or unusual physical or electrical stress including, but not
limited to, exposure to parameters beyond the specified maximum ratings or operation
outside the specified operating range.
5. Neither indemnity against nor license of a third party’s industrial and intellectual property right, etc. is granted
by us in connection with the use of the product and/or the information and drawings contained herein. No
responsibility is assumed by us for any infringement of a third party’s right which may result from the use
thereof.
6. The products listed in this document are intended for use in general electronics equipment for commercial
applications (e.g., office automation, communication equipment, measurement equipment, consumer
electronics, etc.). These products are not authorized for use in any system or application that requires special or
enhanced quality and reliability characteristics nor in any system or application where the failure of such
system or application may result in the loss or damage of property, or death or injury to humans.
Such applications include, but are not limited to, traffic and automotive equipment, safety devices, aerospace
equipment, nuclear power control, medical equipment, and life-support systems.
7. Certain products in this document may need government approval before they can be exported to particular
countries. The purchaser assumes the responsibility of determining the legality of export of these products and
will take appropriate and necessary steps at their own expense for these.
8. No part of the contents contained herein may be reprinted or reproduced without our prior permission.
Copyright 2002 Oki Electric Industry Co., Ltd.
16/16
相关型号：
MSM51V16160F-70JS
Fast Page DRAM, 1MX16, 70ns, CMOS, PDSO42, 0.400 INCH, 1.27 MM PITCH, PLASTIC, SOJ-42
OKI
MSM51V16165A-60TS-K
EDO DRAM, 1MX16, 60ns, CMOS, PDSO44, 0.400 INCH, 0.80 MM PITCH, PLASTIC, TSOP2-50/44
OKI
MSM51V16165A-70TS-K
EDO DRAM, 1MX16, 70ns, CMOS, PDSO44, 0.400 INCH, 0.80 MM PITCH, PLASTIC, TSOP2-50/44
OKI
MSM51V16165A-80TS-K
EDO DRAM, 1MX16, 80ns, CMOS, PDSO44, 0.400 INCH, 0.80 MM PITCH, PLASTIC, TSOP2-50/44
OKI
MSM51V16165B-50JS
EDO DRAM, 1MX16, 50ns, CMOS, PDSO42, 0.400 INCH, 1.27 MM PITCH, PLASTIC, SOJ-42
OKI
MSM51V16165B-60JS
EDO DRAM, 1MX16, 60ns, CMOS, PDSO42, 0.400 INCH, 1.27 MM PITCH, PLASTIC, SOJ-42
OKI
©2020 ICPDF网 联系我们和版权申明