AP-A [OMRON]
TERMINAL ENCLOSE SIDEMNT RESIN;
| 型号： | AP-A |
| 厂家： | 
OMRON ELECTRONICS LLC |
| 描述： | TERMINAL ENCLOSE SIDEMNT RESIN 瞄准线 |
| 文件： | 总2页 (文件大小：352K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Z/A/X/DZ Common Accessories
CSM_Z_A_X_DZ_OP_E_4_2
Common to Z, A, X, and DZ Models
Terminal Covers (Sold Separately)
Separator (Sold Separately)
The Terminal Covers can be attached to Z, A, X, and DZ Switches.
Use a Separator when it is difficult to
provide a sufficient insulation distance or
when using the Switch near metal parts or
copper wires.
The Terminal Cover is secured with mounting screws and protects the casing and terminal wires
from dust, vibration, or fingers, thus preventing terminal short-circuiting, ground faults, wire
disconnection or improper connection, and electric shock accidents.
Terminal Covers made of phenol resin have five or six thin wall sections. These sections can be
torn open for providing holes for lead cables at desired points.
A terminal cover can’t be used in the case of using an actuator sold separately.
Operation Information
Model
SEPARATOR FOR Z
Operation Information
Application Soldering terminal use Screw terminal use
Remarks
Material
Mounting direction
Side mounting
Model
AP-Z
Phenol resin
AP-A
AP-B
---
Metal press mold Side mounting
Vinyl chloride Side mounting
AP1-A
AP1-B
Used for AP-A and AP-B
---
Note: Use a Terminal Cover for screw terminals fir DZ-series Switches with soldering terminals.
Dimensions (Unit: mm)
Terminal Covers
52.8
53.8
25.4
AP-A
Soldering Terminal Use
(Phenol Resin)
AP-B
Screw Terminal Use
(Phenol Resin)
4.3+0.2
4.3+0.2
4.3+0.2
4.3+0.2
25.4
0
0
0
0
8
8
8
8
16.3
6.5
20.2
6.5
2.15R
2.15R
21
21
Note: The Cover has five thin, easy-to-separate
portions for easy lead wire connections.
Note: The Cover has six thin, easy-to-separate
portions for easy lead wire connections.
55.4
25.4
54.4
25.4
AP1-A
Soldering Terminal Use
AP1-B
Screw Terminal Use
4.3+0.2
4.3+0.2
4.3+0.2
4.3+0.2
0
0
0
0
(Metal Press Mold)
(Metal Press Mold)
8
8
17.1
21
2.15R
2.15R
7.2
7
8.5 22.6
8.5 22.6
Note: The Cover has five holes for easy lead wire connections.
Note: The Cover has six holes for easy lead wire connections.
Two, 4.2 dia.
AP-Z
Pressure plate
(t1 steel)
52.8
25.4
Soldering or Screw Terminal Use
21
Cable Pull-out Dimension
(Vinyl Chloride)
7
14
A-A' cross-section
B-B' cross-section
21
6 dia.
15 8 dia.
13
39
46
Note: A 6-dia. or 8-dia. cable can be
used by cutting the cable pull-out
hole to the size of the cable to be
used.
A
B
A'
B'
13
15
M3 × 20 Phillips screw
(with plane washer and nut)
12
Nut
Note: Each dimension has a tolerance of 0.4 mm unless otherwise specified. ( 0.8 mm for the AP-Z)
Separator
Two, 4.5 dia.
13.5
27 0.5
Note: 1. Each dimension has a tolerance of 0.4 mm unless otherwise specified.
2. The material is EAVTC (Epoxide Alkyd Varnished Tetron Cloth) and its heat-resisting
temperature is 130°C.
11.9
25.4 0.2
49.2 0.5
t = 0.51
1
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2015.12
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2015 All Right Reserved.
相关型号：
©2020 ICPDF网 联系我们和版权申明