E3G-L73 [OMRON]
Long-distance Photoelectric Sensor with Built-in Amplifier; 长距离光电传感器放大器内置型型号: | E3G-L73 |
厂家: | OMRON ELECTRONICS LLC |
描述: | Long-distance Photoelectric Sensor with Built-in Amplifier |
文件: | 总12页 (文件大小:909K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Long-distance Photoelectric Sensor with Built-in Amplifier
E3G
CSM_E3G_DS_E_ꢀ_1
Line of Long-distance
Photoelectric Sensors for Large
Workpieces Includes Retro-
reflective Models with Sensing
Distance of 10 m and Distance
Settings Up to 2 m.
• Compact Retro-reflective models require less wiring and
less space with a sensing distance as long as 10 m.
• Distance-setting models feature a teaching function.
• Stability indicator shows at a glance when operating
conditions are stable.
• Relay and selectable NPN/PNP transistor outputs provided.
• Cable, standard connector, and terminal board models
available.
Be sure to read Safety Precautions on
page 8.
Ordering Information
Red light
Model
Infrared light
Sensors (Refer to Dimensions on page 10.)
Appear-
ance
Timer
function
Sensing method
Connection method
Sensing distance
NPN/PNP
selector
Relay output
Pre-wired (2 m)
Connector (M12)
E3G-R13 2M
E3G-R17
---
---
10 m
(500 mm)
*
Retro-reflective
(withMSRfunction)
E3G-MR19
Terminal block
---
E39-R2
(provided)
Yes
E3G-MR19T
Pre-wired (2 m)
Connector (M12)
E3G-L73 2M
E3G-L77
---
---
White paper (300 × 300 mm)
Distance-setting
E3G-ML79
0.2 to 2 m
Terminal block
---
Yes
E3G-ML79T
* Values in parentheses indicate the minimum required distance between the Sensor and Reflector.
Accessories (Order Separately)
Reflectors (Refer to Dimensions on E39-L/F39-L/E39-S/E39-R.)
Appearance
Sensing distance (typical)
Model
Minimum order
Remarks
10 m (500 mm)
(Rated value)*
E39-R2
1
Provided with the E3G-R1@/MR19(T).
6 m (100 mm)*
E39-R1
1
---
* Values in parentheses indicate the minimum required distance between the Sensor and Reflector.
Terminal Protection Cover for Side-pullout Cable (Refer to Dimensions on page 12.)
Appearance
Model
Minimum order
Applicable model
Remarks
E3G-MR19(T)
E3G-ML79(T)
Provided with rubber bushing and cap for pullout
prevention in vertical direction.
E39-L129
1
1
E3G
Mounting Brackets (Refer to E39-L/F39-L/E39-S/E39-R)
Appearance
Model
Quantity
Applicable model
Remarks
E39-L131
1
---
E3G-R1@
E3G-L7@
E39-L132
E39-L135
E39-L136
1
1
1
Rear-mounting use
Cable pulled out in the downward direction
E3G-MR19(T)
E3G-ML79(T)
---
Note: Mounting Brackets are not provided with Sensors and must be purchased separately.
Sensor I/O Connectors (M12) (Refer to Dimensions on XS2.)
Cable
Appearance
Cable type
2 m
Model
XS2F-D421-DC0-A
Straight
Three-
conductor
type
5 m
2 m
5 m
XS2F-D421-GC0-A
XS2F-D422-DC0-A
XS2F-D422-GC0-A
Standard
L-shaped
Note: Refer to Introduction to Sensor I/O Connectors for details.
2
E3G
Ratings and Specifications
Sensing method
Item Model
Sensing distance 10 m (500 mm)*1 (when using E39-R2)
Retro-reflective (with MSR function)
Distance-setting
E3G-L77 E3G-ML79
E3G-R13 E3G-R17 E3G-MR19 E3G-MR19T
E3G-L73
E3G-ML79T
White paper (300 x 300 mm): 0.2 to 2 m
White paper (300 x 300 mm): 0.5 to 2 m
Setting distance
---
---
---
Standard
sensing object
Opaque: 80-mm dia. min.
---
Differential travel
(typical)
10% of setting distance
---
Directional angle Sensor: 1° to 5°
Reflectivity char-
acteristics (black/
white error)
10% max. (at 1-m sensing distance)
Light source
Red LED (650 nm)
(wavelength)
Infrared LED (860 nm)
Spot size
---
70 dia. max. (at 1-m sensing distance)
12 to 240 VDC 10%,
12 to 240 VDC 10%,
Power supply
voltage
10 to 30 VDC,
ripple (p-p): 10%
ripple (p-p): 10% max.
24 to 240 VAC 10% at 50/
60 Hz
10 to 30 VDC,
ripple (p-p): 10% (p-p)
ripple (p-p): 10% max.
24 to 240 VAC 10% at 50/
60 Hz
Current/Power
consumption
50 mA max.
2 W max.
60 mA max.
2 W max.
Load power supply voltage:
30 VDC max.
Load power supply voltage:
30 VDC max.
Load current: 100 mA max.
Residual voltage:
Load current: 100 mA max.
Residual voltage:
Relay output: SPDT, 3 A
(cosφ= 1) max. at 250 VAC or
3 A max. at 30 VDC
Relay output: SPDT, 3 A
(cosφ= 1) max. at 250 VAC or
3 A max. at 30 VDC
Control output
NPN output: 1.2 V max.
PNP output: 2.0 V max.
Open collector output
(NPN/PNP selectable)
L.ON/D.ON selectable
NPN output: 1.2 V max.
PNP output: 2.0 V max.
Open collector output
(NPN/PNP selectable)
L.ON/D.ON selectable
L.ON/D.ON selectable
L.ON/D.ON selectable
Me-
50,000,000 operations min.
(switching frequency: 18,000
operations/h)
50,000,000 operations min.
(switching frequency: 18,000
operations/h)
Life
chani-
cal
---
---
expect-
ancy
100,000 operations min.
(switching frequency: 1,800
operations/h)
100,000 operations min.
(switching frequency: 1,800
operations/h)
(relay
output)
Electri-
cal
---
---
Power supply reverse polarity
Power supply reverse polarity
Protection
circuits
protection,Outputshort-circuit Mutual interference preven-
protection,Outputshort-circuit Mutual interference preven-
protection, Mutual interfer-
ence prevention
tion
protection, Mutual interfer-
ence prevention
tion
Response time
Operate or reset: 1 ms
Operate or reset: 30 ms max. Operate or reset: 5 ms
Operate or reset: 30 ms max.
Sensitivity
adjustment
One-turn adjuster
Teaching (in NORMAL or ZONE mode)
ON- or OFF-
delay: 0 to 5 s
(adjustable)
ON- or OFF-
delay: 0 to 5 s
(adjustable)
Timer function
---
---
Ambient
illumination
(Receiver side)
Incandescent lamp: 3,000 lx max.
Sunlight: 10,000 lx max.
Ambient tempera-
ture range
Operating: −25° to 55°C, Storage: −30° to 70°C (with no icing or condensation)
Ambient humidity
range
Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation
resistance
20 MΩ min. at 500 VDC
Dielectric
strength
2,000 VAC, 50/60 Hz for
1 min.
2,000 VAC, 50/60 Hz for
1 min.
1,000 VAC, 50/60 Hz for 1 min
1,000 VAC, 50/60 Hz for 1 min
Vibration
resistance
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions
Degree of
protection
IEC 60529 IP67 (with protective cover)
Pre-wired
Pre-wired
(Standard
length: 2 m)
Connection
method
Connector
(M12)
Connector
(M12)
(Standard
Terminal block
Terminal block
length: 2 m)
Weight
(packed state)
Approx. 150 g Approx. 50 g Approx. 150 g
Approx. 50 g Approx. 150 g
Case
Lens
PBT (polybutylene terephthalate)
Mechacrylic resin
Mate-
rial
Accessories *2
Reflector, Adjustment screwdriver, and Instruction manual
Adjustment screwdriver and Instruction manual
*1. Values in parentheses indicate the minimum required distance between the Sensor and Reflector.
*2. Mounting Brackets are sold separately.
3
E3G
Engineering Data (Typical)
E3G-R/MR Retro-reflective Models
Excess Gain vs. Set Distance
Parallel Operating Range
500
E39-R2 Reflector
400
E39-R2 Reflector
Y
300
200
100
0
100
10
X
2
4
6
8
10
12
Set distance X (m)
−100
−200
−300
−400
Operating level
1
0.1
0
5
10
15
20
Distance (m)
E3G-L/ML Distance-setting Models
Spot Diameter vs. Sensing Distance
Operating Range in NORMAL Mode
Operating Range in ZONE Mode
40
40
120
Distance setting: 0.5, 1, and 2 m
Sensing object: White paper
300 x 300 mm
Distance setting: 1 and 2 m
Sensing object: White paper
300 x 300 mm
Horizontal
Vertical
Y
Y
30
20
30
100
X
X
20
10
80
60
40
20
10
1 m
2 m
0.5 m
0
0
−10
−20
−10
0.5 m
2 m
1 m
−20
−30
−40
−30
−40
0
0.5
1
1.5
2
2.5
0
0.5
1
1.5
2
2.5
0
0.5
1
1.5
2
2.5
Set distance X (m)
Set distance X (m)
Distance (m)
Sensing Object Size vs. Setting
Distance
Sensing Object Angle Characteristics Sensing Object Angle (Horizontal)
(Vertical)
3
20
15
20
15
White paper
Black paper
Sensing object: White paper
Sensing distance: 1 m
Distance setting: 0.5, 1, and 2 m
Sensing object: White paper
Sensing distance: 1 m
2.5
2
10
5
10
5
2 m
1.5
1
0
0
(Upwards
and
Downwards)
Inclination
angle
+θ
−θ
−5
−10
−5
−10
(Left and
Right)
1 m
Inclination
angle
+θ
−θ
0.5 m
0.5
−15
−20
−15
−20
Sensing object
10 20
Inclination angle (θ)
Sensing object
10 20
Inclination angle (θ)
0
100
200
300
400
500 600
−40 −30 −20 −10
0
30 40
−40 −30 −20 −10
0
30 40
Side length (one side) of sensing object: d (mm)
4
E3G
Close-range Characteristics
Sensing Distance vs. Sensing Object Sensing Distance vs. Sensing Object
Material (at 1-m Setting Distance)
Material (at 500-mm Setting Distance)
600
1.2
2.5
500
400
300
200
2.03 m
1
0.8
0.6
0.4
2
1.5
1
1.24 m
0.51 m 0.52 m
0.5
0
100
0
0.2
0
53 mm
60 mm
43 mm
0 mm
Black White
paper paper
(0.5 m) (0.5 m)
Black White
paper paper
(2 m) (2 m)
Material (teaching distance m)
Material
Material
I/O Circuit Diagrams
NPN Output
Operation
Operation
selector
Model
mode
Timing charts
Output circuit
Incident light
No incident light
10 to 30 VDC
Brown
Black
Blue
Operation
indicator
(Orange)
Stability
indicator
(Green)
1
4
3
Operation
indicator
(orange)
Output
ON
OFF
ON
PNP output
transistor
L side
(L-ON)
ZD
ZD
Light-ON
Load Load
current
Photo-
electric
Sensor
main
NPN or PNP
output selector
transistor
OFF
Control output
*
Operate
Reset
Load
(relay)
circuit
E3G-R13
E3G-R17
E3G-L73
E3G-L77
NPN output
transistor
0 V
Incident light
* Set the NPN or PNP selector to NPN.
No incident light
Connector Pin Arrangement
Operation
indicator
(orange)
Output
ON
OFF
ON
D side
(D-ON)
1
Dark-ON
2
4
3
transistor
OFF
Pin 2 is not used.
Operate
Reset
Load
(relay)
PNP Output
Operation
Operation
selector
Model
mode
Timing charts
Output circuit
Incident light
No incident light
Operation
indicator
(orange)
Output
10 to 30 VDC
ON
OFF
ON
Operation
indicator
(Orange)
Brown
Black
Blue
Stability
indicator
(Green)
1
4
3
L side
(L-ON)
PNP output
transistor
ZD
Light-ON
Photo-
transistor
OFF
*
electric
Sensor
main
NPN or PNP
output selector
Control output
Load
Operate
Reset
Load
(relay)
E3G-R13
E3G-R17
E3G-L73
E3G-L77
circuit
Load
current
NPN output
transistor
ZD
0 V
Incident light
* Set the NPN or PNP selector to PNP.
Connector Pin Arrangement
No incident light
Operation
indicator
(orange)
Output
ON
OFF
ON
D side
(D-ON)
1
Dark-ON
2
4
transistor
3
OFF
Pin 2 is not used.
Operate
Reset
Load
(relay)
5
E3G
Relay Output
Timer
func-
tion
Operation
selector
Model
Timing charts
Output circuit
Incident light
No incident light
L side
(L-ON)
ON
OFF
ON
Operation
indicator
(orange)
Ta
OFF
E3G
-MR19
E3G
None
-ML79
Incident light
No incident light
D side
(D-ON)
ON
OFF
ON
Operation
indicator
(orange)
1
2
3
4
5
Tc
Ta
Tb
Ta
Contact output
(G6C Relay built in)
OFF
T
1
T2
T
2
T
2
T2 T2
Photo-
electric
Sensor
main
24 to 240 VAC or
12 to 240 VDC
(no polarity restriction)
T
1
T
1
T
1
T
1
T1
Power
supply
Incident light
No incident light
ON
L side
(L-ON)
circuit
Td1
Td1
ON-delay*
OFF
ON
Td
2
Td2
Td2
E3G
OFF-delay*
OFF
-MR19T
E3G
-ML79T
Yes
T1
T2
T2 T2
T2 T2
T1
T1
T1
T1
T1
Incident light
No incident light
ON
D side
Td1
Td1
Td1
(D-ON)
ON-delay*
OFF
ON
Td2
Td2
OFF-delay*
OFF
Note: Td1, Td2: Delay time (0 to 5 s)
T1: A period longer than the delay time.
T2: A period shorter than the delay time.
* For ON- and OFF-delay timers, Td1 and Td2 are independently variable.
Plug (Sensor I/O Connector)
Pin No.
Wire color
Brown
Classifi-
Wire Connector
Application
1
2
3
4
cation
color
Brown
---
pin No.
2
4
Blue
Black
1
3
1
2
3
4
Power supply (+V)
---
DC
XS2F-D421-DC0-A
XS2F-D421-GC0-A
XS2F-D422-DC0-A
XS2F-D422-GC0-A
Blue
Black
Power supply (0 V)
Output
Note: Pin 2 is not used.
6
E3G
Nomenclature
Retro-reflective
Distance-setting
E3G-R13 (Pre-wired Model)
E3G-L73 (Pre-wired Model)
E3G-R17 (Standard Connector Model)
E3G-L77 (Standard Connector Model)
Stability indicator (Green)
Teaching indicator
(Red and green)
Operation indicator
(Orange)
Mode selector:
TEACH, RUN (D-ON),
RUN (L-ON)
Operation indicator
(Orange)
Stability indicator
(Green)
Output selector
Output selector
Sensitivity adjuster
Operation selector
NORMAL/ZONE
selector
TEACH button
E3G-MR19 (Terminal Block Model)
E3G-ML79 (Terminal Block Model)
E3G-MR19T (Terminal Block Model with Timer)
E3G-ML79T (Terminal Block Model with Timer)
Stability indicator (Green)
Teaching indicator
(Red and green)
Operation indicator
(Orange)
Stability indicator (Green)
Operation indicator
(Orange)
Mode selector
Operation selector
NORMAL/ZONE selector
Sensitivity adjuster
ON-delay adjuster *
TEACH button
ON-delay adjuster *
Operation selector
*
OFF-delay adjuster
*
OFF-delay adjuster
* The ON- or OFF-delay
adjuster is not available
with the E3G-MR19.
* The ON- or OFF-delay
adjuster is not available
with the E3G-MR79.
7
E3G
Safety Precautions
Refer to Warranty and Limitations of Liability.
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
● Mounting
Mounting
Mounting Directions
Do not use it for such purposes.
• Make sure that the sensing side of the
Sensor is parallel with the surface of
each sensing object. Do not incline the
Sensor towards the sensing object.
Precautions for Correct Use
Do not use the product in atmospheres or environments that exceed
product ratings.
Sensing side
Surface of
sensing object
E3G-R/MR
● Designing
Power Supply
If the sensing object has a glossy
surface, incline the Sensor by 5° to 10°
as shown below, provided that the
Sensor is not influenced by any
background objects.
A power supply with full-wave rectification can be connected to the
E3G-MR19(T).
● Wiring
The tensile strength of the cable during operation should not exceed
the values shown below.
Glossy object
Tensilestrength
Model
• If there is a mirror-like object below the Sensor, the Sensor may not
be in stable operation. Therefore, incline the Sensor or keep the
Sensor a distance away from the mirror-like object as shown below.
(torque)
E3G-R13
50 N max.
E3G-MR19(T)
E3G-R17
10 N max.
Sensing
object
● Adjusting
Mirror-like object
Indicators
• The following illustration indicates the operating levels of the E3G.
• Set the E3G so that it will work within the stable operation range.
• Make sure not to install the Sensor in the incorrect direction. Refer
to the following.
Stability indicator
(green)
Operation indicator (orange)
L. ON
D. ON
Stable
operation
range*
ON
OFF
ON
Operating
level x 1.2
Unstable
operation
range *
OFF
Operating
level
Sensing
Sensing
Sensing
object
object
object
Moving direction
Moving direction
Operating
level x 0.8
OFF
ON
Moving direction
Stable
operation
range*
ON
Install the Sensor as shown in the following if each sensing object
greatly differs in color or material.
*If the operating level is set to the stable operation range, the E3G will operate with the
highest reliability and without being influenced by temperature change, voltage fluctuation,
dust, or setting change. If the operating level cannot be set to the stable operation range,
pay close attention to environmental changes while operating the E3G.
E3G-L/ML
● Designing
Power Supply
A power supply with full-wave rectification can be connected to the
E3G-ML79(T).
Moving direction
Moving direction
● Others
EEPROM Write Errors
● Wiring
The tensile strength of the cable during operation should not exceed
the values shown below.
If a teaching data error occurs with the operation indicator flashing
due to a power failure or static noise, perform the teaching operation
of the Sensor again.
Tensile strength
Model
(torque)
E3G-L73
50 N max.
E3G-ML79(T)
E3G-L77
10 N max.
8
E3G
E3G-M@(T)
● Wiring
All E3G Models
● Designing
Load Relay Contact
• The cable with an external diameter of 6 to 8 mm is recommended.
• Be sure to attach the cover with screws securely in order to
maintain the water- and dust-resistive properties of the product.
The size of the conduit opening is PF1/2 in accordance with JIS
B0202.
• Do not tighten the Terminal Protection Cover with wires pinched
between the Sensor and the cover in order to maintain the water-
and dust-resistive properties of the product.
If E3G is connected to a load with contacts that spark when the load
is turned OFF (e.g., a contactor or valve), the normally-closed side
may be turned ON before the normally-open side is turned OFF or
vice-versa. If both normally-open output and normally-closed output
are used simultaneously, apply an surge suppressor to the load.
Refer to OMRON’s PCB Relays Catalog (X33) for typical examples of
surge suppressors.
Recommended Example
● Wiring
Connecting and Wiring
The E3G has a built-in function to protect the E3G from load
shortcircuiting. If load shortcircuiting results, the output will be turned
OFF. In that case, check the wiring and turn ON the E3G again so that
the short-circuit protection circuit will be reset. This function will
operate if the output current flow is at least 2.0 times the rated load
current. If a capacitive load is connected to the E3G, make sure that
the inrush current does not exceed 1.2 times the rated load current.
Terminal
protection cover
Rubber bushing*
63 mm
Washer*
1Tc
● Mounting
2Ta Output
Clamping nut*
Mounting Conditions
3Tb
4
• If Sensors are mounted face-to-face, make sure that no optical
axes cross each other. Otherwise, mutual interference may result.
• Be sure to install the Sensor carefully so that the directional angle
range of the Sensor will not be directly exposed to intensive light,
such as sunlight, fluorescent light, or incandescent light.
• Do not strike the Photoelectric Sensor with a hammer or any other
tool during the installation of the Sensor, or the Sensor will loose its
water-resistive properties.
Power supply
5
33 mm
*Not provided with UL-compliant (-US) models.
For UL certified products (-US type), use UL-
Listed plastic cable gland.
.
The tightening torque is 3 N m or less.
• Changing to Side-pullout Cable from Vertical-pullout Cable
1
2
• Use M4 screws to mount the Sensor.
• When mounting the case, make sure that the tightening torque
applied to each screw does not exceed 1.2 N·m.
E39-L129 Terminal
Protection Cover
● Water Resistance
Rubber bushing
Washer
Tighten the operation cover screws and terminal block cover screws
to a torque of 0.3 to 0.5 N·m in order to ensure water resistivity.
2
Clamping nut
3
4
Rubber bushing*
*Provided with the E39-L129.
Cap*
Proce-
dure
Operation
1
Remove the present cover.
Attach the E39-L129 Terminal Protection Cover for side-
pullout cable.
2
Remove the clamping nut, washer, and rubber bushing of
the E3G. These are used for the side-pullout cable.
3
4
Attach the rubber bushing and cap provided with the
E39-L129 to the E3G as replacements.
9
E3G
(Unit: mm)
Dimensions
Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.
Sensors
Retro-reflective Models
Standard Connector Model
E3G-R17
Pre-wired Model
E3G-R13
Operation selector
Operation indicator (orange)
Note: All dimensions other than the
ones specified below are the
same as the corresponding
dimensions of E3G-R13.
M2.6
Sensitivity
adjuster
Stability indicator
(green)
12
47.8
45
Mounting
Holes
1.1
R11
Two, 4.5-dia.
mounting
holes
Receiver
Two, M4
R7
22
25
25
29
68.5
67.8
18.8
14
8
7
24.4
10
Emitter
12
21
43
37
43
8
M12 Connector
10.5 dia.
6-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.38 mm2,
Insulator diameter: 1.3 mm),
Standard length: 2 m
Terminal Block Models
E3G-MR19
E3G-MR19T
Operation indicator (orange)
Operation
selector
M2.6
Stability indicator
(green)
OFF-delay adjuster*
ON-delay adjuster*
*The ON- or OFF-delay adjuster is not
available with the E3G-MR19.
Sensitivity adjuster
Mounting Holes
Two, 4.5-dia.
mounting holes
12
Receiver
R7
Two, M4
R11
22
14
18.8
74
74
84.95 84.45
35.95
6
37
Emitter
2.1
16
37
68
Hexagonal nut
(Diagonal: 22)
Applicable cable:
6 to 8 dia.
12
29
44
PF1/2 conduit: JIS B 0202
10
E3G
Distance-setting Models
Pre-wired Model
E3G-L73
Standard Connector Model
E3G-L77
Operation indicator (orange)
TEACH button
Note: All dimensions other than the
M2.6
Operation
selector
Stability indicator (green)
Teaching indicator (red/green)
ones specified below are the
same as the corresponding
dimensions of the E3G-L73.
Mounting
Holes
47.8
45
14
Two, 4.5-dia.
mounting
holes
Receiver
Two, M4
25
14-dia. lens
18
25
29
68.5
67.8
30
12.8
8
7
Emitter
13.7
21
43
10
6-dia. vinyl-insulated round cable with 3 conductors
(conductor cross section: 0.38 mm ,
insulator diameter: 1.3 mm)
Standard length: 2 m
2
37
43
8
M12 Connector
10.5 dia.
Terminal Block Models
E3G-ML79
E3G-ML79T
Operation
selector
Operation indicator (orange)
Stability indicator (green)
Teaching indicator (red/green)
M2.6
*The ON- or OFF-delay adjuster is not
available with the E3G-ML79.
OFF-delay adjuster*
ON-delay adjuster*
Two, 4.5-dia.
TEACH button
Mounting Holes
14
M2.6 nut
mounting holes
Two, M4
Receiver
14-dia. lens
30
18
74
74
84.95 84.45
24.4
6
37
Emitter
13.7
29
16
37
68
Hexagonal nut
(Diagonal: 22)
Applicable cable:
6 to 8 dia.
44
PF1/2 conduit: JIS B 0202
11
E3G
Accessories (Order Separately)
Terminal Protection Cover for Side-pullout Cable
E39-L129
Terminal Protection Cover for Side-pullout Cable
(Example: E3G-MR19)
M2.6
M2.6
61.8
19
29
81.5
22
Hexagonal nut
(Diagonal: 22)
Applicable cable:
6 to 8 dia.
90.3
81
Note: 1. The cover is provided with a rubber bushing and cap
to prevent the cable from being pulled out vertically.
2. Refer to page 9 for the mounting method of the
product.
44
Cap (provided with the E39-L129)
(PF1/2 conduit: JIS B 0202)
Reflectors
Refer to E39-L/F39-L/E39-S/E39-R for details.
Mounting Brackets
Refer to E39-L/F39-L/E39-S/E39-R for details.
Sensor I/O Connectors
Refer to Introduction to Sensor I/O Connectors for details.
12
相关型号:
E3G-ML79T
Line of Long-distance Photoelectric Sensors for Large Workpieces Includes Retroreflective Models with Sensing Distance of 10 m and Distance Settings Up to 2 m.
OMRON
E3G-MR19T
Line of Long-distance Photoelectric Sensors for Large Workpieces Includes Retroreflective Models with Sensing Distance of 10 m and Distance Settings Up to 2 m.
OMRON
E3G-MR19T-US
Line of Long-distance Photoelectric Sensors for Large Workpieces Includes Retroreflective Models with Sensing Distance of 10 m and Distance Settings Up to 2 m.
OMRON
©2020 ICPDF网 联系我们和版权申明