J-7-V [OMRON]
Ultra Subminiature Basic Switch; 超小型基本开关型号: | J-7-V |
厂家: | OMRON ELECTRONICS LLC |
描述: | Ultra Subminiature Basic Switch |
文件: | 总8页 (文件大小:221K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Ultra Subminiature Basic Switch
J
Subminiature Models Capable of
Large-capacity Loads
Snap-action switch allows large-capacity switching
(7 A at 250 VAC) in spite of its small size
(8.9 12.7 5.1 mm).
Particularly suitable as control switches for
applications where there are restrictions on
installation space and weight.
Easy positioning, as the pin plunger is located in
alignment with the center line of one of the two
mounting holes.
RC
Ordering Information
Model Number Legend
J-7j-j
1
2
3
1. Ratings
3. Actuator
None: Pin plunger
7:
7 A at 250 VAC
V:
Short hinge lever
Hinge lever
2. Contact Material
V3:
V4:
None: Gold-plated silver
Long hinge lever
Y:
Silver
V22: Short hinge roller lever
V2: Hinge roller lever
List of Models
Actuator
Model
Pin plunger
J-7
Short hinge
lever
J-7-V
Hinge lever
J-7-V3
J-7-V4
Long hinge lever
Short hinge roller
lever
J-7-V22
J-7-V2
Hinge roller lever
Note: Externally mounted levers JAL and JAL2 are sold sepa-
rately. Refer to page 208.
203
J
J
Specifications
Ratings
Rated voltage
Resistive load
125 VAC
7 A
7 A
250 VAC
Note: The ratings values apply under the following test conditions:
Ambient temperature: 20 2°C
Ambient humidity: 65 5%
Operating frequency: 30 operations/min
Switching Capacity per Load (Reference Values)
Voltage
Non-inductive load
Resistive load Lamp load
NC NO
Inductive load
Inductive load
NC NO
Motor load
NC
NO
NC
NO
125 VAC
7 A
7 A
1.5 A
1.5 A
1.5 A
1.5 A
1.5 A
0.4 A
0.2 A
0.7 A
0.7 A
4 A
4 A
2.5 A
2.5 A
2.5 A
2.5 A
2.5 A
0.03 A
0.02 A
1.3 A
1.3 A
250 VAC
8 VDC
7 A
0.7 A
0.7 A
0.7 A
0.4 A
0.2 A
3 A
1.3 A
1.3 A
14 VDC
30 VDC
125 VDC
250 VDC
7 A
3 A
5 A
3 A
1.3 A
0.4 A
0.2 A
0.03 A
0.02 A
0.03 A
0.02 A
Note: 1. The above values are for the steady-state current.
2. Inductive load has a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
4. Motor load has an inrush current of 6 times the steady-state current.
Characteristics
Operating speed
0.05 mm to 1 m/s (pin plunger models)
Operating frequency
Mechanical: 400 operations/min max.
Electrical: 30 operations/min max.
Insulation resistance
100 MΩ min. (at 500 VDC)
Contact resistance (initial value)
Dielectric strength
15 mΩ max.
600 VAC, 50/60 Hz for 1 min between terminals of the same polarity
1,500 VAC, 50/60 Hz for 1 min between each terminal and non-current-carrying metal part and
between current-carrying metal part and ground.
Vibration resistance (see note 2)
Shock resistance (see note 2, 3)
Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
2
Destruction: 1,000 m/s {approx. 100G} max.
2
Malfunction: 200 m/s {approx. 20G} max. (pin plunger models)
Durability (see note 4)
Mechanical: 10,000,000 operations min. (60 operations/min)
Electrical: 50,000 operations min. (30 operations/min)
Degree of protection
IEC IP40
Class I
Degree of protection against
electric shock
Proof tracking index (PTI)
Ambient operating temperature
Ambient operating humidity
Weight
175
–10°C to 80°C (at ambient humidity of 60% max.) (with no icing)
85% max. (for 5°C to 35°C)
Approx. 1 g (pin plunger models)
Note: 1. The data given above are initial values.
2. Malfunction: 1 ms max.
3. For the pin plunger models, the values are at the free position and total travel position. For the lever models, they are at the total
travel position.
4. For testing conditions, consult your OMRON sales representative.
204
J
J
Approved Standards
Contact Form
Consult your OMRON sales representative for specific models with
standard approvals.
SPDT
UL508 (File No. E41515)/
CSA C22.2 No. 55 (File No. LR21642)
Rated voltage
125 VAC
250 VAC
J-7
7 A
Contact Specifications
Specification
Rivet
Contact
Material
Silver plated
Gold plated
Gap (standard value)
0.35 mm
Inrush
current
NC
NO
15 A max.
7 A max.
Minimum applicable load
30 mA at 5 VDC
Engineering Data (Reference Values)
Mechanical Durability
Electrical Durability
100,000
1,000
700
Without load
Operating frequency:
400 operations/min
Resistive load: cosφ = 1
Operating frequency:
20 operations min. max.
70,000
50,000
500
cosφ=1
30,000
Ambient temperature: 20 2 °C
Ambient humidity: 65 5%
Ambient temperature: 20 2 °C
300
200
Ambient humidity: 65 5%
125 VAC
10,000
100
250 VAC
7,000
5,000
70
50
3,000
1,000
30
20
10
0
0.1
0.2
0.3
0.4
0.5
0
1
2
3
4
5
6
7
8
Overtravel (mm)
Switching current (A)
205
J
J
Dimensions
Mounting Holes
Note: All units are in millimeters unless otherwise indicated.
M 2.3 screw holes
4.8 0.1
Dimensions and Operating Characteristics
Note: 1. All units are in millimeters unless otherwise indicated.
2. Unless otherwise specified, a tolerance of 0.2 mm applies to all dimensions.
3. The operating characteristics are for operation in the A direction ( ).
Model
J-7
Pin Plunger Models
J-7
3.5 dia.
OF max. 1.37 N {140 gf}
A
PT
RF min.
PT max.
OT min.
0.27 N {28 gf}
0.6 mm
astic pin plunger)
8.9
OP
2.3
0.1 mm
2.3
5.1
MD max. 0.15 mm
OP 8.1 0.3 mm
+0.05
–0.025
2.5
dia.
3.95
4.8 0.05
12.7
5.1 0.1
Short Hinge Lever Models
t = 0.3
ee nt
A
Model
J-7-V
9.3
J-7-V
2.3
OF max. 0.49 N {50 gf}
PT
RF min.
PT max.
OT min.
0.08 N {9 g}
1.7 mm
9.15 0.4
OP
8
11.45 0.4
6.6
0.35 mm
2.3
5.1
MD max. 0.5 mm
OP
8.3 1.2 mm
a.
3.95
4.8 0.05
12.7
14.7
5.1 0.1
Note: Stainless-steel spring lever
t = 0.3
(see note)
A
Model
J-7-V3
Hinge Lever Models
J-7-V3
2.3
9.3
OF max. 0.29 N {30 gf}
PT
RF min.
PT max.
OT min.
0.04 N {5 gf}
2.9 mm
9.15 0.4
OP
8
6.6
5.1
11.45 0.4
0.5 mm
2.3
+0.05
MD max. 0.7 mm
2.35
–0.025
+0.05
–0.025
2.5
dia.
OP
8.3 1.9 mm
+0.05
2.35
–0.025 dia.
a.
3.95
4.8 0.05
Note: Stainless-steel spring lever
12.7
14.7
5.1 0.1
206
J
J
t = 0.3
Model
J-7-V4
(Stainless-steel
spring lever)
A
OF max. 0.20 N {20 gf}
Long Hinge Lever Models
J-7-V4
RF min.
PT max.
OT min.
0.02 N {3 gf}
4.5 mm
0.8 mm
MD max. 1.2 mm
OP 8.3 2.9 mm
+0.05
–0.025
1 dia.
2.5
dia.
+0.05
–0.025 dia.
2.35
1.5 dia.
Short Hinge Roller Lever Models
J-7-V22
Model
J-7-V22
4.8 dia. 2.2 (Stainless-steel roller)
A
OF max. 0.54 N {55 gf}
RF min.
PT max.
OT min.
0.04 N {5 gf}
1.6 mm
0.25 mm
t = 0.3
(see note)
MD max. 0.4 mm
OP
14.7 1 mm
+0.05
–0.025
1 dia.
2.5
dia.
+0.05
–0.025 dia.
1.5 dia.
Note: Stainless-steel spring lever
2.35
Hinge Roller Lever Models
J-7-V2
Model
J-7-V2
4.8 dia. 2.2
(Stainless-steel roller)
A
OF max. 0.324 N {33 gf}
RF min.
PT max.
OT min.
0.02 N {3 gf}
2.7 mm
t = 0.3
(see note)
0.45 mm
MD max. 0.7 mm
OP 14.7 1.9 mm
+0.05
–0.025
Note: Stainless-steel spring lever
2.5
dia.
1 dia.
+0.05
–0.025 dia.
1.5 dia.
2.35
207
J
J
Actuators
t = 0.3
Leaf Spring
(see note 1)
8.3
3.6
A
JAL
Accessories (Sold Separately)
Model
JAL
FP
Two, M2.3 × 10
OP
OF max. 1.95 N {199 gf}
RF min.
PT max.
0.54 N {56 gf}
2.3
5.2
5.2 mm
(reference value)
see note 2
3
4.8
4.8 0.1
13.6
Insulating separator
5.6
OT min.
0.3 mm
StainlMesDs-smteeal sxp.ring0le.v8ermm
ote: 1.
2. J-7 Subminiature Basic Switch
FP max.
OP
13.1 mm
8.7 0.8 mm
JAL2
6.3
A
4.8 dia. × 27
(see note 1)
Model
JAL2
FP
OP
OF max. 1.95 N {199 gf}
RF min.
PT max.
0.54 N {56 gf}
2.3
3.6 mm
(reference value)
5.2
see note 2
3
5.6
4.8
OT min.
0.3 mm
4.8 0.1
13.6
Insulating separator
MD max. 0.8 mm
Note: 1. Stainless-steel spring lever
FP max.
19.5 mm
2. J-7 Subminiature Basic Switch
OP
15.1 0.8 mm
Precautions
Refer to pages 26 to 31 for common precautions.
Correct Use
Mounting
Use two M2.3 screws with plain washers or spring washers to se-
curely mount the Switch. Tighten the screws to a torque of 0.19 to
0.29 N S m {2 to 3 kgf S cm}.
Soldering
To solder the lead to the terminal, apply a soldering iron rated at
30 W max. quickly (within 3 seconds) with the actuator at the free
position.
Applying a soldering iron for too long a time or using one that is rated
at more than 30 W may degrade the Switch characteristics.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527
Certain Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed 12. Warranties. (a) Exclusive Warranty. Seller's exclusive warranty is that the
part of all catalogs, manuals or other documents, whether electronic or in writ-
ing, relating to the sale of goods or services (collectively, the "Goods") by
Omron Electronic Components LLC and its subsidiary companies ("Seller").
Seller hereby objects to any terms or conditions proposed in Buyer's purchase
order or other documents which are inconsistent with, or in addition to, these
Terms. Please contact your Omron representative to confirm any additional
terms for sales from your Omron company.
Goods will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Seller (or such other period expressed
in writing by Seller). Seller disclaims all other warranties, express or implied.
(b) Limitations. SELLER MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR
A PARTICULAR PURPOSE OF THE GOODS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
GOODS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Seller further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Goods or other-
wise of any intellectual property right. (c) Buyer Remedy. Seller's sole obliga-
tion hereunder shall be to replace (in the form originally shipped with Buyer
responsible for labor charges for removal or replacement thereof) the non-
complying Good or, at Seller's election, to repay or credit Buyer an amount
equal to the purchase price of the Good; provided that in no event shall Seller
be responsible for warranty, repair, indemnity or any other claims or expenses
regarding the Goods unless Seller's analysis confirms that the Goods were
properly handled, stored, installed and maintained and not subject to contami-
nation, abuse, misuse or inappropriate modification. Return of any goods by
Buyer must be approved in writing by Seller before shipment. Seller shall not
be liable for the suitability or unsuitability or the results from the use of Goods
in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any
advice, recommendations or information given orally or in writing, are not to be
construed as an amendment or addition to the above warranty.
2. Prices. All prices stated are current, subject to change without notice by
Seller. Buyer agrees to pay the price in effect at time of shipment.
3. Discounts. Cash discounts, if any, will apply only on the net amount of
invoices sent to Buyer after deducting transportation charges, taxes and
duties, and will be allowed only if (i) the invoice is paid according to Seller's
payment terms and (ii) Buyer has no past due amounts owing to Seller.
4. Orders. Seller will accept no order less than $200 net billing.
5. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Goods.
6. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Seller or required to be collected directly or
indirectly by Seller for the manufacture, production, sale, delivery, importation,
consumption or use of the Goods sold hereunder (including customs duties
and sales, excise, use, turnover and license taxes) shall be charged to and
remitted by Buyer to Seller.
7. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Seller, Seller reserves the right to stop shipments or require satisfactory 13. Damage Limits; Etc. SELLER SHALL NOT BE LIABLE FOR SPECIAL, INDI-
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Seller may (without liability
and in addition to other remedies) cancel any unshipped portion of Goods sold
hereunder and stop any Goods in transit until Buyer pays all amounts, includ-
ing amounts payable hereunder, whether or not then due, which are owing to it
by Buyer. Buyer shall in any event remain liable for all unpaid accounts.
8. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Seller fully against all costs or expenses arising in
connection therewith.
RECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUC-
TION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE
GOODS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY,
NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of
Seller exceed the individual price of the Good on which liability is asserted.
14. Indemnities. Buyer shall indemnify and hold harmless Seller, its affiliates and
its employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Seller is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Goods. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Seller and defend or settle
any action brought against Seller to the extent that it is based on a claim that
any Good made to Buyer specifications infringed intellectual property rights of
another party.
15. Property; Confidentiality. The intellectual property embodied in the Goods is
the exclusive property of Seller and its affiliates and Buyer shall not attempt to
duplicate it in any way without the written permission of Seller. Notwithstand-
ing any charges to Buyer for engineering or tooling, all engineering and tooling
shall remain the exclusive property of Seller. All information and materials
supplied by Seller to Buyer relating to the Goods are confidential and propri-
etary, and Buyer shall limit distribution thereof to its trusted employees and
strictly prevent disclosure to any third party.
16. Miscellaneous. (a) Waiver. No failure or delay by Seller in exercising any right
and no course of dealing between Buyer and Seller shall operate as a waiver
of rights by Seller. (b) Assignment. Buyer may not assign its rights hereunder
without Seller's written consent. (c) Amendment. These Terms constitute the
entire agreement between Buyer and Seller relating to the Goods, and no pro-
vision may be changed or waived unless in writing signed by the parties.
(d) Severability. If any provision hereof is rendered ineffective or invalid, such
provision shall not invalidate any other provision. (e) Setoff. Buyer shall have
no right to set off any amounts against the amount owing in respect of this
invoice. (f) As used herein, "including" means "including without limitation".
9. Force Majeure. Seller shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
10. Shipping; Delivery. Unless otherwise expressly agreed in writing by Seller:
a. Shipments shall be by a carrier selected by Seller;
b. Such carrier shall act as the agent of Buyer and delivery to such carrier
shall constitute delivery to Buyer;
c. All sales and shipments of Goods shall be FOB shipping point (unless oth-
erwise stated in writing by Seller), at which point title to and all risk of loss of
the Goods shall pass from Seller to Buyer, provided that Seller shall retain a
security interest in the Goods until the full purchase price is paid by Buyer;
d. Delivery and shipping dates are estimates only.
e. Seller will package Goods as it deems proper for protection against normal
handling and extra charges apply to special conditions.
11. Claims. Any claim by Buyer against Seller for shortage or damage to the
Goods occurring before delivery to the carrier must be presented in writing to
Seller within 30 days of receipt of shipment and include the original transporta-
tion bill signed by the carrier noting that the carrier received the Goods from
Seller in the condition claimed.
Certain Precautions on Specifications and Use
1. Suitability of Use. Seller shall not be responsible for conformity with any stan- 2. Programmable Products. Seller shall not be responsible for the user's pro
dards, codes or regulations which apply to the combination of the Good in the
gramming of a programmable Good, or any consequence thereof.
Buyer's application or use of the Good. At Buyer's request, Seller will provide 3. Performance Data. Performance data given in this catalog is provided as a
applicable third party certification documents identifying ratings and limitations
of use which apply to the Good. This information by itself is not sufficient for a
complete determination of the suitability of the Good in combination with the
end product, machine, system, or other application or use. The following are
guide for the user in determining suitability and does not constitute a warranty
It may represent the result of Seller's test conditions, and the user must corre
late it to actual application requirements. Actual performance is subject to the
Seller's Warranty and Limitations of Liability.
some examples of applications for which particular attention must be given. 4. Change in Specifications. Product specifications and accessories may be
This is not intended to be an exhaustive list of all possible uses of this Good,
nor is it intended to imply that the uses listed may be suitable for this Good:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government
regulations.
changed at any time based on improvements and other reasons. It is our prac
tice to change part numbers when published ratings or features are changed
or when significant construction changes are made. However, some specifica
tions of the Good may be changed without any notice. When in doubt, specia
part numbers may be assigned to fix or establish key specifications for you
application. Please consult with your Seller's representative at any time to con
firm actual specifications of purchased Good.
5. Errors and Omissions. The information in this catalog has been carefully
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.
(iii) Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to
this Good.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE SELLER'S PRODUCT IS PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at www.omron.com/oei – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ON-LINE
Global - http://www.omron.com
USA - http://www.omron.com/oei
Canada - http://www.omron.ca
OMRON ELECTRONIC
COMPONENTS LLC
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
OMRON CANADA, INC.
885 Milner Avenue
Toronto, Ontario M1B 5V8
416-286-6465
847-882-2288
Cat. No. GC RLY8A
8/04
Specifications subject to change without notice
Printed in USA
相关型号:
©2020 ICPDF网 联系我们和版权申明