WL-8H300 [OMRON]
Two-circuit Limit Switch; 双回路限位开关型号: | WL-8H300 |
厂家: | OMRON ELECTRONICS LLC |
描述: | Two-circuit Limit Switch |
文件: | 总42页 (文件大小:2778K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Two-circuit Limit Switch
WL
Wide Selection of Two-circuit Limit
Switches
A wide selection of models are available, including
the overtravel models with greater OT, lamp-
equipped models for checking operation, low-tem-
perature and heat-resistant models, and microload
models.
Microload models are added to the product lineup.
Meets EN/IEC standards (only Switches with
ground terminals).
Switches with ground terminals have the CE
marking.
uCE
Approved Standards
Agency
Standard
UL508
CSA C22.2 No. 14 LR45746
EN60947-5-1 R9551016
File No.
UL
E76675
CSA
TÜV Rheinland
Note: Contact your OMRON representative for more information on approved models.
Ordering Information
Clas s ification
Specifications
Roller lever
Standard Overtravel
High-
precis ion
Features
Page
Actua-
tors
11 to
25
Yes
Yes
Yes
---
Yes
Five models: Roller lever, adjustable roll-
er lever, adjustable rod lever, fork lever
lock, rod spring lever.
Plunger
---
Six models: Top plunger, top-roller plung-
er, top-ball plunger, horizontal plunger,
horizontal-roller plunger, horizontal-ball
plunger.
Flexible rod
Yes
Yes
---
---
Two models: coil spring and steel wire.
Load/
contact
Standard load
SPST-NO/
SPST-NC
type
Standard models use a two-circuit
double-break switch.
Microload
SPST-NO/
SPST-NC
type
Yes
Specifications include gold-plated con-
tacts.
1
WL
WL
Specifications
Airtight-seal
Standard Overtravel
High-
precis ion
Features
Page
Envi-
ron-
ment-
resist-
ant
models
(See
note 3.)
Yes (Cannot be used with heat-resis-
tive and low-temperature models.)
29
WLj -55
Uses an airtight-sealed built-in switch.
Her-
metic
seal
Molded
termi-
nals
WLj -139
Lead wires are attached.
The case cover and conduit section are
molded from epoxy resin to improve seal-
ing performance.
WLj -140
WLj -141
Lead wires are attached.
The case is filled with epoxy resin, to en-
sure high sealing performance.
The Head opening is protected from cut-
ting powder. (WLj -141)
Only WLG2, WLCA2, and WLGCA2 can
be fabricated. (WLj -141 models.)
Anti-
coolant
WLj -RP60
Lead wires are attached.
The case is filled with epoxy resin, to en-
sure high sealing performance. To im-
prove the anti-coolant properties (water-
soluble coolant), rubber with high chemi-
cal-resistance has been used.
Spatter-preven-
tion
WLj -S
Yes
To improve spatter prevention during
welding, a heat-resistant resin is used,
and screws and rollers are all made from
stainless steel.
26 to
29
29
Heat-resistive
WLj -TH
Yes (Cannot be used with airtight, her- To improve heat resistance, silicone rub-
metic, low-temperature, corrosion-
proof, or lamp-equipped models.)
ber is used for rubber parts and for the
built-in switch.
The operating temperature range is +5_C
to 120_C.
Low-temperature
WLj -TC
WLj -RP
Yes (Cannot be used with airtight, her- To improve low temperature resistance,
metic, heat-resistive, corrosion-proof, silicone rubber is used.
or lamp-equipped models.)
The operating temperature range is
-- 4 0 _C to 40_C.
Corrosion-proof
(See note 4.)
Yes (Cannot be used with lamp-
equipped models.)
Diecast parts such as the switch box are
made of corrosion-proof aluminum. Rub-
ber-sealing parts are made of fluorine
rubber and exposed nuts and screws are
made of stainless steel. These all aid in
resisting oil, chemicals and adverse
weather conditions.
Outdoor specifi-
cations
WLj -P1
---
Yes
(See note
6.)
---
Rotary shafts are made of unquenched
(i.e., untreated) stainless steel to improve
corrosion resistance. Exposed nuts and
screws are made of stainless steel and
rubber sealing parts of silicone rubber.
These factors all combine to create a
product which is resistant to temperature
changes and adverse weather condi-
tions.
(See note
5.)
Lamp-equipped
Relevant pages
Operating status can be checked at a
glance.
Lit when operating and not lit when not
operating.
WLj -LE: 100 VAC/VDC min.
WLj -LD: 115 VAC/VDC min. (Refer to
page 27 for detailed ratings.)
31
---
WLj -LE
WLj -LD
Yes
Yes
Pages 11 to 31
---
Note: 1. Do not expose to extreme changes in temperature.
2. Standard Models:
Operate on each side at an angle of 45_.
Possible to set to one-side operation on either side.
Pretravel (PT) is 15_.
Overtravel Models:
Standard and high-sensitivity models operate on each side at an angle of 80_.
Not possible to set to one-side operation.
-2N Series operate on each side at an angle of 90_.
Possible to set to one-side operation on either side.
High-precision Models: Operate on each side at an angle of 45_.
Possible to set to one-side operation on either side.
Pretravel (PT) is 5_.
3. When ordering, add the suffix for the environment-resistant model or indicator specifications required according to the operating
environment and purpose.
2
WL
WL
4. The overtravel model (-2N Series), fork lever lock model (WLCA32-41 to 44), horizontal plunger (WLSDj ) model, heat-resistive
model, low-temperature model, and lamp-equipped model cannot be used with the corrosion-proof model.
5. Outdoor specifications are available for some standard models. Consult your OMRON representative for details.
6. Outdoor specifications are only available for general models and high-sensitivity models.
Lis t of Models
Rotating Lever Models
Roller Lever Models : Short, Medium, and Long Lever Models
Actuator (See note 2.)
Type
Total travel (TT)
Features
WL-1A100 Roller WL-1A200 Roller WL-1A300 Roller
Lever: Short
lever (R38)
Lever: Medium
lever (R50)
Lever: Long
lever (R63)
Standard
One-side operation is
WLCA2
WLCA2-7
WLCA2-8
possible. (See note 3.)
Head can be mounted in
any of the four directions.
Over-
travel
General
One-side operation is im- WLH2
possible. (See note 3.)
Head can be mounted in
any of the four directions.
---
---
---
---
---
---
High-sen-
sitivity
One-side operation is
WLG2
possible. (See note 3.)
Head can be mounted in
any of the four directions.
-2N Series
One-side operation is
WLCA2-2N
possible. (See note 3.)
Head can be mounted in
any of the two directions.
(When the Head can be
mounted horizontally, the
Head can be mounted in
any of the four directions.)
High-precision
One-side operation is
WLGCA2
---
---
possible. (See note 3.)
Head can be mounted in
any of the four directions.
Note: 1. For the approved standards file numbers, refer to page 1.
2. For external dimensions and other information, refer to pages 22 to 25.
3. One-side operation means that three operational directions can be selected electrically, according to the change in direction of the
operating plunger. Those models for which one-side operation is impossible can only operate on both sides. For details, see page
39.
3
WL
WL
Adjus table Roller Levers and Adjus table Rod Levers
Actuator (See note 2.)
WL-2A100 WL-4A100
Type
Total Travel (TT)
Features
Adjus table
Roller Lever
Adjus table Rod
Lever (Adjus table
length: 25 to
140 mm)
WL-3A100
(Adjus table length:
350 to 380 mm)
Standard
One-side operation possible. (See note 3.)
Head can be mounted in any of the four direc-
tions.
WLCA12
---
---
WLCL (WL-4A100)
WLHL (WL-4A100)
Over-
travel
General
One-side operation possible. (See note 3.)
Head can be mounted in any of the four direc-
tions.
WLH12
WLHAL4
(WL-3A100)
High-sen-
sitivity
One-side operation possible. (See note 3.)
Head can be mounted in any of the four direc-
tions.
WLG12
WLGL (WL-4A100)
-2N Series
One-side operation is possible. (See note 3.)
Head can be mounted in any of the two direc-
tions. (When the Head can be mounted hori-
zontally, the Head can be mounted in any of
the four directions.)
WLCA12-2N
WLCL-2N
(WL-4A100)
Note: 1. For the approved standards file numbers, refer to page 1.
2. For external dimensions and other information, refer to page 22 to 25.
3. One-side operation means that three operational directions can be selected electrically, according to the change in direction of the
operating plunger. The operating plungeris set for operation on both sides before delivery. Those models forwhich one-side opera-
tion is impossible can only operate on both sides. For details, see page 39. The operational plunger is factory-set to both sides.
Rod Spring Levers and Fork Lever Locks
Actuator (See note 2.)
Type
Total travel (TT)
Features
WL-3A200 Rod
Spring Lever
Fork Lever Locks :
WL-5A100,
WL-5A102,
WL-5A104
Protective
Head can be mounted in any of the four direc-
tions.
---
WLCA32-41
(WL-5A100)
WLCA32-42
(WL-5A102)
WLCA32-43
(WL-5A104)
Over-
travel
General
One-side operation is possible. (See note 3.)
Head can be mounted in any of the four direc-
tions.
WLHAL5
---
Note: 1. For the approved standard file numbers, refer to page 1.
2. For external dimensions and other information, refer to page 22 to 25.
3. One-side operation means that three operational directions can be selected electrically, according to the change in direction of the
operating plunger. The operating plungeris set for operation on both sides before delivery. Those models forwhich one-side opera-
tion is impossible can only operate on both sides. For details, see page 39. The operational plunger is factory-set to both sides.
4
WL
WL
4. The fork lever lock is configured so that the dog pushes the lever to reverse the output and this reversed state is maintained even
after the dog continues on. If the dog then pushes the lever from the opposite direction, the lever will return to its original position.
Example
NC terminal: ON NO terminal: ON NO terminal: ON
Standard Plungers
Type
Standard Flexible Rods
Actuators
Actuators
Model
Model
Top
Coil spring
Top Plunger
WLD
Spring dia. 6.5
Spring dia. 4.8
Resin rod dia. 8.0
1.0-dia. wire
WLNJ
WLNJ-30
WLNJ-2
Top-roller Plunger
Top-ball Plunger
Horizontal Plunger
WLD2
WLD28 (see note 2.)
WLD3
Steel wire
WLNJ-S2
Horizontal
WLSD
Note: For the approved standards file numbers, refer to page 1.
Microload Models
Horizontal-roller
Plunger
WLSD2
A series of microload models has also been developed for the con-
figurations outlined on pages 3 to 5. The model numbers become
WL01j . For example, WLCA2 becomes WL01CA2.
Horizontal-ball Plunger WLSD3
Note: 1. For the approved standards file numbers, refer to
page 1.
2. Sealed roller.
Model Number Legend
WLj j -j j j j j j j j j
1
2
3
4
5
6
7
8
9
10 11
1. Electrical Rating
Blank:
01:
Standard
Miniature
2. Actuator and Head Specifications
Symbol
CA2
Actuator type
Roller lever: Standard (R38)
Switches without levers
WLRCA2
CA2-7
CA2-8
H2
Roller lever: Standard, medium lever (R50)
Roller lever: Standard, long lever (R63)
Roller lever: Overtravel, general-purpose model, 80_
Roller lever: Overtravel, high-sensitivity, 80_
Roller lever: Overtravel, 90_
Roller lever: High-precision
Adjustable roller lever: Standard
Adjustable roller lever: Overtravel, general-purpose model, 80_
Adjustable roller lever: Overtravel, high-sensitivity, 80_
Adjustable roller lever: Overtravel, 90_
WLRCA2
WLRCA2
WLRH2
WLRG2
WLRCA2-2N
WLRGCA2
WLRCA2
WLRH2
WLRG2
WLRCA2-2N
WLRCL
WLRH2
WLRH2
WLRG2
WLRCA2-2N
WLRH2
WLRCA32
WLRCA32
WLRCA32
---
G2
CA2-2N
GCA2
CA12
H12
G12
CA12-2N
CL
HL
HLAL4
GL
CL-2N
HAL5
CA32-41
CA32-42
CA32-43
D
Adjustable rod lever: Standard
Adjustable rod lever: Overtravel, general-purpose model, 80_, 25 to 140 mm
Adjustable rod lever: Overtravel, general-purpose model, 80_, 350 to 380 mm
Adjustable rod lever: Overtravel, high-sensitivity, 80_, 25 to 140 mm
Adjustable rod lever: Overtravel, 90_, 25 to 140 mm
Rod spring lever: Protective, Overtravel, general-purpose model, 80_
Fork lever lock: Protective, WL-5A100
Fork lever lock: Protective, WL-5A102
Fork lever lock: Protective, WL-5A104
Plunger: Top plunger
D2
Plunger: Top-roller plunger
---
D28
Plunger: Top-roller plunger, sealed
---
D3
Plunger: Top-ball plunger
---
5
WL
WL
Symbol
SD
SD2
SD3
NJ
NJ-30
NJ-2
NJ-S2
Actuator type
Switches without levers
Plunger: Horizontal plunger
Plunger: Horizontal-roller plunger
Plunger: Horizontal-ball plunger
Flexible rod: Coil spring
Flexible rod: Coil spring, multi-wire
Flexible rod: Coil spring, resin rod
Flexible rod: Steel wire
---
---
---
---
---
---
---
3. Environment-res is tant Model Specifications
Blank:
RP:
P1:
Standard
Corrosion-proof (See note 1.)
Weather-resistant (See note 1.)
4. Built-in Switch Specifications
Blank:
55:
General-purpose built-in switch
Hermetically-sealed built-in switch (See note 1.)
5. Temperature Specifications
Blank:
TH:
Standard: --10_C to 80_C
Heat-resistive: 5_C to 120_C (See note 1.)
TC:
Low temperature: --40_C to 40_C (See note 1.)
6. Special Hermetic Model Specifications
Blank: No cables or molding
139:
140:
General-purpose built-in switch with cables attached and molded conduit opening and cover(cover cannot be removed). (See note 1.)
Airtight built-in switch with cables attached and molded conduit opening, cover, and case cover (cover cannot be removed).
(See note 1.)
141:
Airtight built-in switch with cables attached and molded conduit opening, cover, and case cover (cover cannot be removed).
The Head opening is created to protect it from cutting powder. (See note 1.)
RP40: Airtight built-in switch with cables attached, SC Connector can be used, molded conduit opening, cover, and case cover
(cover cannot be removed). (See note 1.)
RP60: Airtight built-in switch with cables attached, fluorine rubber-molded conduit opening, cover, and case cover
(cover cannot be removed). (See note 1.)
7. Conduit Size, Ground Terminal Specifications
1
Blank:
G1:
G:
Y:
TS:
G
G
/
/
Without ground terminal
With ground terminal
With ground terminal
With ground terminal
With ground terminal
2
1
2
Pg13.5
M20
/ -14NPT
2
1
8. Indicator Type
Element
Voltage
Leakage Current
Blank:
LE:
LD:
No indicators
Neon lamp
LED
125 to 250 VAC
10 to 115 VAC/VDC
Approx. 0.6 to 1.9 mA
Approx. 1 mA
9. Lever Type
Blank:
A:
Allen-head lever (standard)
Double nut lever
10.
Blank:
S:
Standard
Spatter-proof model (See note 2.)
11. Conduit Wiring Specifications
1
Blank:
K13:
Screw-tightened terminal (G / conduit)
2
Direct-wired Connector (2-core, DC)
Direct-wired Connector (2-core, AC)
Direct-wired Connector (4-core, DC)
Direct-wired Connector (4-core, AC)
K13A:
K43:
K43A:
-M1J:
Pre-wired Connector (2-core, DC) with 0.3-m cable attached.
Pre-wired Connector (4-core, AC) with 0.3-m cable attached.
Pre-wired Connector (4-core, DC) with 0.3-m cable attached.
Pre-wired Connector (3-core, DC) with 0.3-m cable attached.
-AGJ03:
-DGJ03:
-DK1EJ03:
Note: 1. For information on applicable models, see page 29 to 31.
2. For information on applicable models, see pages 26 to 29.
6
WL
WL
General-purpose Models
These LimitSwitches are two-circuitdouble-break switches housed
in rugged diecast, thus making it an oil-tight, waterproof and dust-
proof construction (complies with IP67).
A wide range of actuators with a range of functions are available;
rotating lever, plunger, flexible rod etc.
The rubber material in the standard models is designed to be resist-
ant to water and most oils.
In addition to the standard models, microload models are also avail-
able.
Nomenclature
Set Pos ition Marker Plate
After operation, set the indicator needle on the
marker plate so that is in the convex section of the
bearing. For the WLD2, insert the needle so that is
is between the two main wires on the plunger.
Roller
The rolleris made ofself-lubricating sintered stain-
less steel and boasts high resistance to wear.
Head -mounting
Screws
Lever
The lever forged of anti-corrosive aluminium alloy
features high corrosion resistances and outstand-
ing ruggedness. With roller lever, adjustable rod
and flexible rod models, the actuator position can
be set anywhere within 360_. (The lever cannot be
mounted in the opposite direction.)
Requires maintenance (excessive overtravel)
Proper range
Requires
maintenance
(insufficient overtravel)
Proper range
Requires maintenance
(excessive overtravel)
Roller Lever Sets crew
Operational Plunger (See note 2.)
Head
The Head used in the roller lever type, adjustable
rod lever type, or horizontal plunger type (except
the -2N Series) can be mounted in any of the four
directions by removing the screws at the four cor-
ners of the Head.
Cover Seal
By using an O-ring as the cover seal, an optimum
squeeze can be obtained and high sealing proper-
ties are assured as well.
Terminal Screws
M4 screws
Shaft Section Seal
By fitting an O-ring to the rotary shaft and with an
appropriate interference of the screws, high-seal-
ing properties are maintained.
Cover
Ins ulator
The insulator has outstanding insulation proper-
ties and prevents the generation of any gases
which may corrode the internal parts.
Bearing
The bearing smooths the plunger movement.
Built-in Switch
Cover Sets crew
The built-in switch (for all models except the micro-
load models) has an extended mechanical life of 15
million operations or more.
A Phillips screw is used to ensure ease of use.
Conduit Opening (See note 1.)
The conduit threads are parallel threads for G /
tube and offer further increased sealing properties
when used in conjunction with the SC connector.
1
2
1
1
Note: 1. The display for conduit threads has changed from PF / to G / according to revisions of JIS B 0202. This is only a change in the
2
2,
1
display, so the thread size and pitch have not changed. (Conduit threads Pg 13.5 and / -14NPT are also available.)
2
2. By changing the orientation of the operational plunger, three operational directions can be selected electrically. (This is only pos-
sible with general-purpose roller lever, adjustable roller lever, and adjustable rod lever models. For the overtravel models, only -2N
Series models have this function.)
Ratings
Non-inductive load
Res is tive load Lamp load
NC NO NC NO
10 A 10 A
Inductive load
Inductive load Motor load
NC NO NC NO
10 A
Type
Rated
voltage
Standard,
overtravel
(except
high-sensitivity
models), and
high-precision
models.
125 VAC
250 VAC
500 VAC
8 VDC
3 A
1.5 A
1 A
5 A
2.5 A
1.5 A
0.8 A
10 A
10 A
10 A
10 A
6 A
10 A
10 A
2 A
10 A
3 A
3 A
1.5 A
6 A
0.8 A
3 A
1.5 A
6 A
10 A
10 A
6 A
14 VDC
30 VDC
125 VDC
250 VDC
125 VAC
250 VAC
125 VDC
250 VDC
6 A
3 A
6 A
4 A
3 A
4 A
0.8 A
0.4 A
5 A
0.2 A
0.1 A
---
0.2 A
0.1 A
0.8 A
0.4 A
---
0.2 A
0.1 A
---
Overtravel
(high-sensitivity)
5 A
---
---
---
0.4 A
0.2 A
Note: 1. The above figures are for standard currents.
2. Inductive loads have a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
7
WL
WL
4. Motor load has an inrush current of 6 times the steady-state current.
5. For PC loads, use the microload models.
NC
NO
30 A max. (15 A max. (see note))
20 A max. (10 A max. (see note))
Inrush current
Note: Only for high-sensitivity overtravel models.
Microload Models
Ground Terminal Models
Rated voltage
125 VAC
30 VDC
Res is tive load
WL
-
0.1 A
1
2
Operation within the three zones illustrated in the following diagram
will produce optimum performance.
1: Type of actuator
2: Conduit opening size
The models differ depending on the size of the case’s conduit
thread.
Recommended Load Range: 5 to 30 VDC, 0.5 to 100 mA
Model
Conduit opening s ize
1
G1
G
G /
2
Pg 13.5
Y
M20
1
TS
/ -14NPT
2
0.8 W
5 mW
Current (mA)
Contact Form
Standard (WLj )/Microload (WL01j ) Models
8
WL
WL
Approved Standard Ratings
UL/CSA
Standard Models: A600
Current
Volt-amperes
Rated voltage
Carry current
10 A
Make
Break
Make
7,200 VA
Break
720 VA
120 VAC
240 VAC
480 VAC
600 VAC
60 A
30 A
15 A
12 A
6 A
3 A
1.5 A
1.2 A
Microload Models:
0.1 A 125 VAC, 0.1 A 30 VDC
TÜV (EN60947-5-1)
(Only Ground Terminal Models are Approved)
Model
WLj -j
Category/rating
Thermal
current
Indicator
AC-15 2 A/250 V
DC12 2 A/48 V
10 A
---
WL01j -j
AC-14 0.1 A/125 V 0.5 A
DC12 0.1 A/48 V
---
WLj -j LE
AC-15 2 A/250 V
10 A
Neon lamp
Neon lamp
LED
WL01j -j LE AC-14 0.1 A/125 V 0.5 A
WLj -j LD
AC-15 2 A/115 V
DC12 2 A/48 V
10 A
WL01j -j LD AC-14 0.1 A/115 V 0.5 A
LED
DC12 0.1 A/48 V
Note: As an example, AC-15 2 A/250 V means the following:
Application category
AC-15
2 A
Rated operating current (Ie)
Rated operating voltage (Ue)
250 V
9
WL
WL
Characteris tics
Degree of protection
IP67
Life expectancy (s ee note 3)
Mechanical: 15,000,000 operations min. (see note 4)
Electrical: 750,000 operations min. (see note 5)
Operating s peed
1 mm to 1 m/s (for WLCA2)
Operating frequency
Mechanical: 120 operations/minute min.
Electrical: 30 operations/minute min.
Rated frequency
50/60 Hz
Ins ulation res is tance
Contact res is tance
Dielectric s trength
100 MΩ min. (at 500 VDC)
25 mΩ max. (initial value)
1,000 VAC (600 VAC), 50/60 Hz for 1 min between non-continuous terminals.
2,200 VAC, 50/60 Hz for 1 min/Uimp 2.5 kV non-current-carrying metal part and ground.
2,200 VAC, 50/60 Hz for 1 min Uimp 2.5 kV between each terminal and
non-current-carrying metal part.
Rated ins ulation voltage (U )
250 V (EN60947-5-1)
1,000 V max. (EN60947-5-1)
3 (EN60947-5-1)
i
Switching overvoltage
Pollution degree
(operating environment)
Short-circuit protective device (SCPD)
Conditional s hort-circuit current
10 A, fuse type gG or gI (IEC269)
100 A (EN60947-5-1)
Conventional enclos ed thermal current 10 A, 0.5 A (EN60947-5-1)
(I
)
the
Protection agains t electric s hock
Vibration res is tance
Class I
10 to 55 Hz, 1.5-mm double amplitude (see note 6)
2
Shock res is tance
Destruction: 1,000 m/s min.
2
Malfunction: 300 m/s min. (see note 6)
Ambient temperature
Ambient humidity
Operating: --10°C to 80°C (with no icing) (see note 7)
Operating: 95% max.
Weight
Approx. 275 g (in the case of WLCA2)
Note: 1. The above figures are initial values.
2. The figures in parentheses for dielectric strength, are those for the overtravel (high-sensitivity) model.
3. Life expectancy values are calculated at an operating temperature of 5°C to 35°C, and an operating humidity of 40% to 70%. Con-
tact your OMRON sales representative for more detailed information on other operating environments.
4. 10,000,000 operations min. for general, high-sensitivity, and flexible rod overtravel models.
5. 500,000 operations min. forhigh-precision and outdoorspecifications models. Allmicroload models however, are 1,000,000 opera-
tions min.
6. Except the flexible rod models.
7. For low temperature models this is --40_C to 40°C (no icing). For heat-resistive models the range is +5°C to 120°C.
Engineering Data
Electrical Life Expectancy
Operating temperature: 5°C to 30°C
Operating humidity: 40% to 70%.
Operating frequency: 30 operations/min
cosφ = 1
125 VAC
250 VAC
480 VAC
Switching current (mA)
10
WL
WL
Standard Models
Dimens ions /Operating Characteris tics
Note: 1. Rotating Lever Models: For all models WLj indicates a standard model and WL01j indicates a microload model.
2. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
Roller Lever
Roller Lever
WLCA2
WL01CA2
WLCA2-7
WL01CA2-7
60 max.
67.2 max.
17.5 dia. × 15 (See note)
17.5 dia. × 7 (see note)
Four, M3.5
Four, M3.5
M5 × 12
Allen-head
bolt
M5 × 12
Allen-head
bolt
Four, 5.2+o0.2
Four, 5.2+o0.2
dia.
dia.
holes
holes
Three, M4 × 13
Three, M4 × 13
Four, M6
Depth: 15 min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
JIS B0202 G1/2
Effective thread:
4 threads min.
42 max.
42 max.
Note: Stainless sintered roller
Note: Stainless steel roller
Roller Lever
Adjus table Roller Lever
WLCA2-8
WL01CA2-8
WLCA12
WL01CA12
60 max.
67 max.
17.5 dia. × 7 (see note)
17.5 dia. × 7 (see note)
Four, M3.5
Adjustable range:
25 to 89
M5 × 16
Allen-head
bolt
Four, M3.5
Four, 5.2+o0.2
Four, 5.2+o0.2
dia. holes
dia.
holes
M5 × 12
Allen-head
bolt
Three, M4 × 13
Three, M4 × 13
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
42 max.
42 max.
Note: Stainless sintered roller
Note: Stainless sintered roller
Operating characteris tics
WLCA2
WL01CA2
WLCA2-7
WL01CA2-7
WLCA2-8
WL01CA2-8
WLCA12
WL01CA12
(s ee note)
Operating force: OF max.
Release force: RF min.
Pretravel: PT
13.34 N
10.2 N
8.04 N
13.34 N
2.23 N
15±5°
30°
1.67 N
15±5°
30°
1.34 N
15±5°
30°
2.23 N
15±5°
30°
Overtravel: OT min.
Movement differential: MD max.
12°
12°
12°
12°
Note: The operating characteristics for WLCA12 and WL01CA12 are measured at the lever length of 38 mm.
11
WL
WL
OF and RF for WLCA12, with a lever length of 89 mm.
Operating characteris tics
OF
RF
WLCA12, WL01CA12
5.68 N
0.95 N
Rotating Lever Models: For all models WL indicates a standard model and WL01j indicates a microload model.
Adjus table Rod Lever
Fork Lever Lock
WLCL
WL01CL
WLCA32-41 to 44
WL01CA32-41 to 44
(For details s ee page 4.)
62.5 max.
55 max.
Two, 17.5 dia. × 7
(see note)
3±0.2 dia. × 160
Adjustable range:
25 to 140
(See note)
M8×12
Four, M3.5
Allen-head
set screw
Four, M3.5
M5 × 12
Allen-head bolt
M5 × 16
Allen-head
bolt
Four,
+0.2
5.2
dia. holes
0
Four,
+0.2
0
5.2
dia. holes
Three, M4 × 13
Three, M4 × 13
JIS B0202 G1/2
Effective thread:
4 threads min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
Four, M6
Depth: 15 min.
42 max.
42 max.
Note: Plastic roller. This illustration shows the external dimen-
sions of the WLCA32-41. (Models WLCA32-041 to -044
have stainless steel rollers.)
Note: Stainless steel rod
WLCA32-41
WLCA32-42
WLCA32-43
WLCA32-44
Note: 1. Unless otherwise indicated, a tolerance of ±0.4 mm ap-
Operating characteris tics
Operating force: OF max.
Release force: RF min.
Pretravel: PT
WLCL, WL01CL
plies to all dimensions.
1.39 N
2. The fork lever lock is configured so that the dog pushes
the lever to reverse the output and this reversed state is
maintained even after the dog continues on. If the dog
then pushes the leverfrom the opposite direction, the le-
ver will return to its original position.
0.27 N
15±5°
30°
Overtravel: OT min.
Movement differential: MD max. 12°
Example
Note: The operating characteristics for WLCA12 and WL01CA12
are measured at the lever length of 140 mm.
Operating characteris tics
WLCA32-41 to 44,
WL01CA32-41 to 44
Force necessary to reverse
11.77 N}
the direction of the lever: Max.
Movement until the lever
reverses
50±5°
55°
NC terminal: ON NO terminal: ON NO terminal: ON
Movement until switch
operation: Max.
Movement after switch
operation: Min.
35°
12
WL
WL
Note: 1. Plunger Models: For all models WLj indicates a standard model and WL01j indicates a microload model.
2. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
Top Plunger
Horizontal Plunger
WLD
WL01D
WLSD
WL01SD
9 dia.
(see note)
Four, M3.5
Four, M3.5
Four,
+0.2
0
R1 (see note 1)
5.2
dia. holes
25 dia. (see
note 2.)
Three, M4 × 13
Four,
+0.2
5.2
dia. holes
0
Three, M4 × 13
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
42 max.
42 max.
Note: Stainless steel plunger
Note: 1. Stainless steel plunger
2. Cosmetic nuts.
Top-roller Plunger
Horizontal-roller Plunger
WLD2
WL01D2
WLSD2
WL01SD2
17 dia. × 5 (see note)
Four, M3.5
17 dia. × 5
(see note 1)
Four, M3.5
Four,
+0.2
0
5.2
Four,
+0.2
dia. holes
25 dia.
(see
note 2.)
5.2
dia. holes
0
Three, M4 × 13
Three,
M4 × 13
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
42 max.
42 max.
Note: Stainless sintered roller
Note: 1. Stainless sintered roller
2. Cosmetic nuts
3. The WLSD21 model, which has the roller rotated by 90_ is
also available.
13
WL
WL
Note: Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
Top-ball Plunger
Horizontal-ball Plunger
WLD3
WL01D3
WLSD3
WL01SD3
15.5 dia.
1/2” dia. (see note)
Four, M3.5
Four, M3.5
1/2” dia.
(see note)
Four,
+0.2
Four,
5.2
dia. holes
0
25 dia.
(see
note 2)
+0.2
0
5.2
Three, M4 × 13
dia. holes
Three,
M4 × 13
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
42 max.
42 max.
Note: Stainless steel ball
Note: 1. Stainless steel ball
2. Cosmetic nuts
Sealed Top-roller Plunger
WLD28
WL01D28
11.2 dia. × 5 (see note)
Four, M3.5
Four,
+0.2
0
5.2
dia. holes
Three, M4 × 13
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
42 max.
Note: Stainless steel ball
Operating
characteris tics
WLD
WL01D
WLD2
WL01D2
WLD3
WL01D3
WLD28
WL01D28
WLSD2
WL01SD2
WLSD3
WL01SD3
WLSD
WL01SD
Operating force: OF
max.
26.67 N
26.67 N
26.67 N
16.67 N
40.03 N
40.03 N
40.03 N
Release force: RF min. 8.92 N
8.92 N
1.7 mm
5.6 mm
1 mm
8.92 N
1.7 mm
4 mm
4.41 N
1.7 mm
5.6 mm
1 mm
8.89 N
2.8 mm
5.6 mm
1 mm
8.89 N
2.8 mm
4 mm
8.89 N
2.8 mm
6.4 mm
1 mm
Pretravel: PT max.
Overtravel: OT min.
1.7 mm
6.4 mm
Movement differential: 1 mm
MD max.
1 mm
1 mm
Operating position: OP 34±0.8 mm
44±0.8 mm
44.5±0.8 mm 44±0.8 mm
41 mm 39.5 mm
54.2±0.8 mm 54.1±0.8 mm 40.6±0.8 mm
--- --- ---
Total travel position:
TTP max.
29.5 mm
39.5 mm
14
WL
WL
Note: 1. Flexible Rod Models: For all models WLj indicates a standard model and WL01j indicates a microload model.
2. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
Coil Spring
Coil Spring (Multi-wire)
WLNJ
WL01NJ
WLNJ -30
WL01NJ -30
6.5 dia.
See note 2
4.8 dia.
See note 2
See note 1
See note 1
See note
3
See note
3
Four,
Four,
+0.2
5.2
0
+0.2
5.2
dia. holes
0
dia. holes
Three, M4 × 13
Three,
M4 × 13
Four, M6
Depth: 15 min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
JIS B0202 G1/2
Effective thread:
4 threads min.
42 max.
42 max.
Note: 1. The coil spring may be operated from anydirec-
tion except the axial direction (↓).
Note: 1. The coil spring may be operated from any
direction except the axial direction (↓).
2. Stainless steel coil spring
2. Piano wire coil
3. Optimum operating range of the coil spring is
within 1/3 of the entire length from the top end.
3. Optimum operating range of the coil spring is
within 1/3 of the entire length from the top end.
Coil Spring (Res in Rod)
Steel Wire
WLNJ -2
WL01NJ -2
WLNJ -S2
WL01NJ -S2
8 dia.
See note 1
1 dia.
See note 1
See note 2
See note
3
See note 2
See note
3
M3 × 3 Allen-
head set screw
26 dia.
Four,
Four,
+0.2
5.2
dia. holes
0
+0.2
5.2
dia. holes
0
Three, M4 × 13
Three, M4 × 13
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
42 max.
42 max.
Note: 1. The coil spring may be operated from any direction
except the axial direction (↓).
Note: 1. The coil spring may be operated from any direction
except the axial direction (↓).
2. Polyamide resin rod
2. Stainless steel wire
3. Optimum operating range of the rod is within 1/3 of
the entire length from the top end.
3. Optimum operating range of the wire is within 1/3 of
the entire length from the top end.
Operating characteris tics
WLNJ
WL01NJ
(s ee note)
WLNJ 30
WL01NJ 30
(s ee note)
WLNJ -2
WL01NJ -2
(s ee note)
WLNJ -S2
WL01NJ -S2
(s ee note)
Operating force: OF max.
Pretravel: PT
1.47 N
20±10 mm
1.47 N
20±10 mm
1.47 N
40±20 mm
0.28 N
40±20 mm
Note: These values are taken from the top end of the wire or spring.
15
WL
WL
Overtravel Models
Overtravel models are Limit Switches which are provided with a
greater OT to facilitate dog setting.
The overtravel models are classified into three types; general-pur-
pose, high-sensitivity, and models which are capable of one-side
90_ operation, the -2N Series.
The -2N Series can also be installed on either side.
Since this model is identical to the standard model in dimensions,
both models are interchangeable.
Like the standard model, it is oil-tight, waterproof, and dustproof
(complies with IP67).
Overtravel Models (1)
Overtravel Models (2)
-2N Series
General-purpos e, high
s ens itivity models
Head can be mounted in any
of the four directions.
The Head can be mounted in
two directions, forward and
backward.
The lever operates on either
side at 80_.
The lever operates on either
side at 90_.
One-side operation is
impossible.
One side operation is
possible.
Overtravel Models (1)
General-purpos e/High Sens itivity Models
Dimens ions /Operating Characteris tics
Note: 1. For all models WLj indicates a standard model and WL01j indicates a microload model.
2. One-side operation is not possible with the general-purpose and high-sensitivity models.
3. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
Roller Lever
Adjus table Rod Lever
60 max.
WLH2
WLHL
55 max.
WL01H2
WLG2
WL01HL
WLGL
WL01G2
WL01GL
17.5 dia. × 7 (see note 1)
3¦ 0.2 dia. × 160
(see note 1)
Adjustable range:
25 to 140
Allen-head
lock screw
Four, M3.5
Four, M3.5
M5 × 12
Allen-head
bolt
M5 × 12
Allen-head
bolt
Four,
+0.2
5.2
dia. holes
0
Four,
+0.2
0
5.2
dia. holes
Three, M4 × 13
Three, M4 × 13
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
42 max.
42 max.
Note: 1. WLj GL is identical to other models except in
Note: 1. Stainless sintered roller
the shape of the set position marker plate.
2. WLj G2 is identical to other models except in
2. The built-in switch for WLHL is W-10FB3.
3. The built-in switch for WLGL is W-10FB3-8.
the shape of the set position marker plate.
3. The built-in switch for WLH2 is W-10FB3.
4. The built-in switch for WLG2 is W-10FB3-8.
16
WL
WL
Adjus table Roller Lever
WLH12
67 max.
WL01H12
WLG12
17.5 dia. × 7
WL01G12
Four, M3.5
M5 × 12
Allen-head
bolt
Adjustable range:
25 to 89
Four,
+0.2
0
5.2
dia. holes
Three, M4 × 13
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
42 max.
Note: 1. Stainless sintered roller
2. WLj G12 is identical to other models except in
the shape of the set position marker plate.
3. The built-in switch for WLH12 is W-10FB3.
4. The built-in switch for WLG12 is W-10FB3-8.
Operating
characteris tics
WLH2
WL01H2
WLG2
WL01G2
WLH12
WL01H12
(s ee note 1)
WLG12
WL01G12
(s ee note 1)
WLHL
WL01HL
(s ee note 2)
WLGL
WL01GL
(s ee note 2)
Operating force: OF
max.
9.81 N
9.81 N
9.81 N
9.81 N
2.84 N
2.84 N
Release force: RF min. 0.98 N
0.98 N
0.98 N
0.98 N
0.25 N
0.25 N
10° +2
10° +2
10° +2
Pretravel: PT
15±5°
15±5°
15±5°
-- 1
-- 1
-- 1
Overtravel: OT min.
55°
65°
7°
55°
12°
65°
7°
55°
12°
65°
7°
Movement differential: 12°
MD max.
Note: 1. The operating characteristics of WLH12, WL01HL12, WLG12, and WL01G12 are measured at the lever length of 38 mm.
2. The operating characteristics of WLHL, WL01HL, WLGL, and WL01GL are measured at the rod length of 140 mm.
OF and RF for WLH12 and WL01H12, with a lever length of 89 mm.
Operating
characteris tics
WLH12,
WL01H12
WLG12,
WL01G12
OF
RF
4.18 N
0.42 N
4.18 N
0.42 N
17
WL
WL
Note: 1. For all models WLj indicates a standard model and WL01j indicates a microload model.
2. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
Adjus table Rod Lever
Rod Spring Lever
WLHAL4
WL01HAL4
WLHAL5
WL01HAL5
3.2 dia. (see note)
2.3 dia. (see note)
Adjustable range:
350 to 380
M5 × 16
Allen-head
bolt
M5 × 16
Allen-head
bolt
Four,
Four,
+0.2
+0.2
0
5.2
dia. holes
5.2
0
dia. holes
Three, M4 × 13
Three, M4 × 13
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
42 max.
42 max.
Note: Stainless steel rod
Note: Piano wire
Operating
characteris tics
WLHAL4
WL01HAL4
(s ee note 2)
WLHAL5
WL01HAL5
Operating force: OF max. 0.98 N
0.90 N
Release force: RF min.
Pretravel: PT
0.15 N
15±5°
55°
0.09 N
15±5°
55°
Overtravel: OT min.
Movement differential: MD 12°
max.
12°
Note: 1. With WLHAL4, WL01HAL4, WLHAL5, and WL01HAL5,
the actuator’s tare is large, so depending on the installa-
tion direction, they may not be properly reset. Always
install so that the actuator is facing downwards.
2. The operating characteristics of WLHAL4, and
WL01HAL4 are measured at the rod length of 380 mm.
18
WL
WL
Overtravel Models (2)
-2N Series
-2N Series (90_ operation on one side is possible by simply changing the direction of the cam.)
Dimens ions /Operating Characteris tics
Note: 1. For all models WLj indicates a standard model and WL01j indicates a microload model.
2. With the -2N Series, 90_ operation on one side is possible by simply changing the direction of the cam.
3. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
60 max.
67 max.
Roller Lever
Adjus table Roller Lever
17.5 dia. × 7 (see note)
WLCA2-2N
WL01CA2-2N
WLCA12-2N
WL01CA12-2N
17.5 dia. × 7 (see note)
Four, M3
Adjustable range:
25 to 89
Four, M3
Two, M5 ×
18
Two, M5 × 18
M5 × 12
Allen-head
bolt
M5 × 16
Allen-head
bolt
+0.2
5.2
Four,
dia. holes
0
Two, 5.2 +0.2 dia.
Two, 5.2 +0.2 dia.
0
0
Three, M4 × 13
Three, M4 × 13
JIS B0202 G1/2
Effective thread:
4 threads min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
Four, M6
Depth: 15 min.
Note: Stainless sintered roller
Note: Stainless sintered roller
42 max.
42 max.
55 max.
Adjus table Rod Lever
WLCL-2N
WL01CL-2N
3 ±0.2 dia. ×
160 (see note)
M8 × 12 Allen-
head
lock screw
Four, M3
Adjustable range:
25 to 140
Two, M5 × 18
M5 × 12
Allen-head
bolt
+0.2
0
5.2
Four,
dia. holes
Two, 5.2 +0.2 dia.
0
Three, M4 × 13
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Note: Stainless steel rod
42 max.
Operating characteris tics
WLCA2-2N
WL01CA2-2N
WLCA12-2N
WL01CA12-2N
(s ee note 1)
WLCL-2N
WL01CL-2N
(s ee note 2)
Operating force: OF max.
Release force: RF min.
Pretravel: PT max.
9.61 N
1.18 N
20°
9.61 N
1.18 N
20°
2.84 N
0.25 N
20°
Overtravel: OT min.
70°
70°
70°
Movement differential: MD max.
10°
10°
10°
Note: 1. The operating characteristics of WLCA12-2N and WL01CA12-2N are measured at the lever length of 38 mm.
2. The operating characteristics of WLCL-2N and WL01CL-2N are measured at the rod length of 140 mm.
19
WL
WL
OF and RF for WLCA12-2N and WL01CA12-2N, with a lever length of 89 mm.
Operating
WLCA12-2N, WL01CA12-2N
characteris tics
OF
RF
4.10 N
0.50 N
Cam direction changing procedure
Relationship of cam to operation as
observed from the rear of Switch
Loosen the cam holder with
a coin or screwdriver. Take
out the cam from the Switch.
Change the direction of the cam
as required by your intended op-
eration and then reinstall the cam.
Operation on both sides
Operation on one side
Operates
Operates Operates
Does not operate
Operation on one side
Avoid this combination
Does not operate
Operates
High-precis ion Models
The high-precision models feature a pretravel of 5° (as compared with 15° for the standard models) and a repeat accuracy twice as great as
standard models. The high-precision models are ideal for positioning control of machine tools.
Dimens ions /Operating Characteris tics
For all models WLj indicates a standard model and WL01j indicates a microload model.
Note: Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
60 max.
Roller Lever
WLGCA2
WL01GCA2
17.5 dia. × 7 (see note)
Four, M3.5
M5 × 12
Allen-head
bolt
Operating characteris tics
WLGCA2
WL01GCA2
Four,
+0.2
Operating force: OF max.
Release force: RF min.
Pretravel: PT
13.34 N
1.47 N
5.2
dia. holes
0
Three, M4 × 13
5° +02
40°
Overtravel: OT min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
Movement differential: MD max. 3°
42 max.
Note: Stainless sintered roller
20
WL
WL
Connector Models
The connector models allow easy maintenance.
Dimens ions /Operating Characteris tics
Note: Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
Connector Pin Arrangement
High-s ens itivity
60 max.
Built in s witch terminal No.
Pin NO.
WLG2-j LDK13j
WL01G2-j LDK13j
3 (NO)
4 (NO)
3
4
17.5 dia. × 7 (see note)
Operating characteris tics
WLG2-j LDK13j
WL01G2-j LDK13j
Four, M3.5
M5 × 12
Allen-head
bolt
Operating force: OF max.
Release force: RF min.
Pretravel: PT
9.81 N
0.98 N
Four,
10° +2
+0.2
0
5.2
dia. holes
-- 1
Three, M4 × 13
Overtravel: OT min.
65°
Movement differential: MD max. 7°
Four, M6
Depth: 15 min.
Total travel
80°±5°
M12 × 1
JIS B0202 G1/2
Effective thread:
4 threads min.
42 max.
Note: Stainless steel roller
Connector Pin Arrangement
High-s ens itivity
60 max.
WLG2-j LDK43j
WL01G2-j LDK43j
Built in s witch terminal No.
Pin NO.
1 (NC)
1 (NC)
3 (NO)
4 (NO)
1
2
3
4
17.5 dia. × 7 (see note)
Four, M3.5
M5 × 12
Allen-head
bolt
Operating characteris tics
WLG2-j LDK13j
WL01G2-j LDK13j
Four,
+0.2
0
5.2
dia. holes
Three, M4 × 13
Operating force: OF max.
Release force: RF min.
Pretravel: PT
9.81 N
0.98 N
10° +2
Four, M6
Depth: 15 min.
-- 1
M12 × 1
JIS B0202 G1/2
Effective thread:
4 threads min.
Overtravel: OT min.
65°
42 max.
Movement differential: MD max. 7°
Total travel 80°±5°
Note: 1. Stainless steel roller
2. The indicator is wired on the NO side.
21
WL
WL
Actuators
Dimens ions (Levers Only)
Lever: Only rotating lever models are illustrated.
WL-1A100
Standard Lever
WL-1A115
Res in Roller
WL-1A400
Bearing Roller
17.5 dia. × 7
resin roller
17.5 dia. × 7 stainless
sintered roller
17 dia. × 6
bearing roller
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
M5
M5
Allen-head bolt
M5
Allen-head bolt
Allen-head bolt
WL-1A105
Double Nut
WL-1A103S
Spatter Prevention
WL-1A118
Nylon Roller:
Roller Width: 30 mm
17.5 dia. × 7
stainless steel roller
17.5 dia. × 30
Nylon roller
17.5 dia. × 7
stainless sintered roller
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
M5
M5
Allen-head bolt
Two, M5 Allen-head
nut and arm set screw
Allen-head bolt
WL-1A200
WL-1A300
WL-2A100
Lever Length: 50
Roller Width: 15
Lever Length: 63
17.5 dia. × 7
stainless sintered roller
17.5 dia. × 7
stainless sintered roller
17.5 dia. × 15
stainless steel roller
Adjustable lever:
stainless steel
Adjustable range:
25 to 89
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
M5
Allen-head
bolt
M5
M5
Allen-head bolt
Allen-head bolt
22
WL
WL
WL-2A111
Res in Roller
WL-2A107
Double Nut
WL-2A108
Res in Roller
17.5 dia. × 7
17.5 dia. × 7
M5
Allen-head
bolt
17.5 dia. × 7
resin roller
Adjustable lever:
stainless sintered roller
resin roller
Adjustable lever:
stainless steel
Adjustable lever:
stainless steel
stainless steel
Adjustable range:
28 to 88
Adjustable range:
25 to 140
Adjustable range:
25 to 89
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
M5
Allen-head
bolt
Two, M5 Allen-head
nut and arm set screw
WL-2A122
WL-2A106
17.5 dia. × 7
17.5 dia. × 7
stainless sintered roller
M5
Allen-head
bolt
stainless sintered roller
Adjustable lever:
stainless steel
Adjustable lever:
stainless steel
Adjustable range:
25 to 140
Adjustable range:
25 to 78.5
7.3-dia.
mounting
holes
Note: Can be installed on the rear side.
7.3-dia.
mounting
holes
M5
Allen-head
bolt
Note: Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
WL-2A104
WL-2A110
WL-2A105
50 dia. × 15
Nylon roller
50 dia. × 6
Nylon roller
49 dia. rubber roller
Material: EPDM
Adjustable from
R42 to R89
Adjustable from
R41 to R78.5
Adjustable from
R16 to R89
M5
Allen-head
bolt
7.3-dia.
mounting
holes
M5
Allen-head
bolt
7.3-dia.
mounting
holes
7.3-dia.
M5
mounting
Allen-head
holes
bolt
23
WL
WL
WL-1A106
WL-1A110
WL-4A100
35 dia. × 6
Nylon roller
50 dia. × 6
Nylon roller
3-dia. stainless
steel rod
7.3-dia. mounting holes
Adjust-
able
up to
141
M5 Allen-head
bolt
M5
Allen-head
bolt
M5
Allen-head
bolt
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
WL-3A106
Double Nut
WL-4A201
WL-3A100
3.2-dia.
stainless
steel rod
3.2-dia. stainless
steel rod
2-dia. stainless
steel panel
Adjust-
able
from
350 to
380
Adjust-
able
from 350
to 380
13 dia.
Adjustable to
a maximum
of 290
7.3-dia. mounting
holes
M5
Allen-head
bolt
Actuator’s
center of
rotation
7.3-dia. mounting
holes
M5
Allen-
head bolt
7.3-dia. mounting
holes
Two, M5 Allen-
head nut and
arm set screw
25.5 max.
25.5 max.
2.3-dia. operation
rod
WL-3A108
WL-3A200
WL-3A203
8 dia.
Cap
3.2-dia. stainless
steel rod
Adjust-
able
from
630 to
660
Adhesive
12.5 dia. max.
12.5 dia.
max.
2.3-dia.
operation
rod
M5
Allen-head
bolt
7.3-dia.
mounting
holes
7.3-dia.
mounting
holes
24.6 max.
7.3-dia.
mounting
holes
M5
Allen-head
bolt
M5
Allen-head bolt
24.6 max.
25.5 max.
WL-4A112
WL-2A129
4-dia. stainless
steel rod
Marking
Adjust-
able up
to 141
7.3-dia. mounting
+0.2
Three, 5.30
dia. holes
holes
M5
Allen-head
bolt
+0.1
0
7.3
dia. mounting
holes
Two,
M5 × 16
Allen-head bolts
Note: When using the adjustable roller (rod) lever, make sure that the lever is facing downwards. Use caution, as telegraphing (the Switch
turns ON and OFF repeatedly due to inertia) may occur.
24
WL
WL
WL-5A101
WL-5A103
WL-5A105
Two, 17.5 dia. × 7
stainless sintered
rollers
Two, 17.5 dia. × 7
stainless sintered
rollers
Two, 17.5 dia. × 7
stainless sintered
rollers
+0.1
0
+0.1
0
7.3
dia.
+0.1
0
7.3
dia.
7.3
dia.
M5 × 12 Allen-head bolt
M5 × 12 Allen-head bolt
WL-5A102 has a plastic roller
M5 × 12 Allen-head bolt
WL-5A104 has a plastic roller
WL-5A100 has a plastic roller
Head Models
Actuators
Set model
Head model
WL-1H1100
Head model without lever
Roller lever
WLCA2
WLGCA2
WLG2
WLRCA2
WLRGCA2
WLRG2
WL-1H1100-1 (see note)
WL-2H1100
WLH2
WL-2H1100-1 (see note)
WL-6H1100
WLRH2
WLCA2-2N
WLCA12
WLG12
WLH12
WLCA12-2N
WLCL
WLRCA2-2N
WLRCA2
WLRG2
Adjustable roller lever
WL-1H2100
WL-2H2100
WL-2H2100-1 (see note)
WL-6H2100
WLRH2
WLRCA2-2N
WLRCL
Adjustable rod lever
Top plunger
WL-4H4100
WLGL
WL-2H4100
WLRG2
WLCL-2N
WLD
WL-6H4100
WLRCA2-2N
---
WL-7H100
WLD2
WL-7H200
WLD3
WL-7H300
WLD28
WLSD
WL-7H400
Horizontal plunger
---
WL-8H100
WLSD2
WLSD3
WLCA32-41
WL-8H200
WL-8H300
Fork lever lock
Coil spring
WL-5H5100
WLRCA32
---
WLNJ
WL-9H100
WL-9H200
WL-9H300
WL-9H400
WLNJ-30
WLNJ-2
WLNJ-S2
Note: For the model number of Heads without lever, simply remove the numbers after WL-j H. For example, WL-1H1100 becomes WL-1H.
WLH2 and WLH12 however, become WL-2H-1, and WLGCA2 becomes WL-1H-1. Other Head models are available, but must be
ordered separately.
25
WL
WL
Environment-resistant Models
Spatter-prevention Models
These models are most effective in an arc welding line or places where cutting powder is spattered.
Nomenclature
Double Nut Lever
Allen-head Lever
Roller, Roller Axis
Using stainless steel prevents
spatter from adhering.
SUS304 is used for double nut.
Screws
SUS304 is used, preventing spatter
from adhering.
Operating Lever
Melamine sinter-painted, it is easy to
peel off the spatter.
Head Cap
Using Teflon prevents spatter from adhering.
Note: Spatter means the Zn powder pro-
duced when welding.
Adhering spatter to the Limit Switch
may cause malfunction of lever or
lamp cover.
Lamp Cover
Heat-resistant resin is used for the
lamp cover.
By using spherical surface for the
display part, it disperses the direc-
tion of spatter.
The lack of gap prevents spatter pow-
der from clogging.
Lis t of Models
Rotating Lever Models
Standard Models
Neon lamp
LED
Type
Total travel (TT)
Actuators
125 VAC
Approx. 0.6 mA
WLCA2-LEAS
250 VAC
Approx. 1.9 mA
10 to 115 VAC/DC
Approx. 1.0 mA
WLCA2-LDAS
Standard
One-side operation
is possible
Double nut lever
Allen-head lever
WLCA2-LES
WLCA2-LDS
Overtra- General One-side operation
Double nut lever
Allen-head lever
Double nut lever
Allen-head lever
Double nut lever
WLH2-LEAS
WLH2-LES
WLH2-LDAS
WLH2-LDS
vel
is impossible
High-
sensitiv-
ity
WLG2-LEAS
WLG2-LES
WLG2-LDAS
WLG2-LDS
High-precision
One-side operation
is possible
WLGCA2-LEAS
WLGCA2-LDAS
Allen-head lever
WLGCA2-LES
WLGCA2-LDS
Note: Consult your OMRON representative for the microload WL01j models.
26
WL
WL
Plunger Models
Standard Models
Neon lamp
LED
Actuator
125 VAC
250 VAC
10 to 115 VAC/DC
Approx. 1.0 mA
Approx. 0.6 mA
Approx. 1.9 mA
Seal top-roller plunger
WLD28-LES
WLD28-LDS
Ratings
Non-inductive load
Res is tive load Lamp load
NC NO NC NO
1.5 A
Inductive load
Inductive load Motor load
NC NO NC NO
10 A
Model
Rated
current
WLCA2-LEj
WLH2-LEj
WLGCA2-LEj
WLG2-LEj
WLD28-LES
125 VAC 10 A
250 VAC 10 A
125 VDC 0.8 A
250 VDC 0.4 A
3 A
2 A
5 A
2.5 A
1.5 A
0.2 A
0.1 A
2.5 A
1 A
10 A
0.8 A
0.4 A
10 A
10 A
6 A
3 A
0.2 A
0.1 A
3 A
0.2 A
0.1 A
1.5 A
3 A
0.2 A
0.1 A
5 A
WLCA2-LDj
WLH2-LDj
WLGCA2-LDj
WLG2-LDj
WLD28-LDj
115 VAC
12 VDC
24 VDC
48 VDC
10 A
10 A
6 A
6 A
6 A
4 A
3 A
4 A
3 A
2 A
1.5 A
3 A
2 A
Note: 1. The above figures are for standard currents.
2. Inductive loads have a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
4. Motor load has an inrush current of 6 times the steady-state current.
NC
NO
30 A max.
Inrush current
20 A max.
Operating temperature
Operating humidity
-- 1 0 °C to 80°C (with no icing)
95% max.
Contact Form
Standard Model
Approved Standard Ratings
UL/CSA
LE (Neon Lamp) A300
LD (LED)
Rated voltage
Current
Make Break
Volt-amperes
Make Break
7,200 VA 720 VA
Carry current
Rated Carry
voltage current
115 VAC
115 VDC
10 A
10 A
0.8 A
120 VAC
240 VAC
60 A
30 A
6 A
3 A
27
WL
WL
Dimens ions /Operating Characteris tics
Roller Lever
60 max.
17.5 dia. × 7 (see note)
Four, M3.5 head
clamping screws
Two, M5 Allen-head
nut and arm set screw
Four, 5.2+o0.2
dia. holes
Teflon cap
Lamp cover
Three, M4 × 13
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
42 max.
Note: Stainless steel roller
Overtravel models
Operating characteris tics
Standard
High-precis ion
General
High-s ens itivity
9.81 N
0.98 N
Operating force: OF max.
Release force: RF min.
Pretravel: PT
13.34 N
9.81 N
0.98 N
15°±5°
13.34 N
1.47 N
2.23 N
°
°
°
°
+2
-- 1
+2
-- 0
15°±5°
10°
5°
Overtravel: OT min.
30°
12°
55°
12°
65°
7°
40°
3°
Movement differential: MD max.
Seal Top-roller Plunger
11.2 dia. × 5*
Four, M3.5
Four, 5.2+o0.2
dia. holes
Lamp cover
Three, M4 × 13
JIS B0202 G1/2
Effective thread:
4 threads min.
Four, M6
Depth: 15 min.
42 max.
Note: Stainless steel roller
Operating characteris tics
Operating force: OF max.
WLD28-Lj S
16.67 N
Release force: RF min.
Pretravel: PT max.
4.41 N
1.7 mm
5.6 mm
1 mm
Overtravel: OT min.
Movement differential: MD max.
Operating position: OP
Total travel position: TTP max.
44±0.8 mm
39.5 mm
Note: Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
28
WL
WL
Spatter-prevention Parts
All parts of the Switch have spatter-prevention properties, so be sure to use the following products for maintenance of Spatter-prevention Limit
Switches.
Levers /Lamp-equipped Covers
Type
Without lever
Complete Head
(lever with Head)
Allen-head lever
Lamp-equipped
cover
Double nut lever
Model
Add an “R” to the prod-
uct number to order.
E.g.: WLj CA2-LES
WL-1A105S
WL-1A103S
WL-1H1100S
(in case of WLCA2-j ,
WLGCA2-j )
WL-LES
(Neon Lamp)
(forward and backward (forward and backward
lever) lever)
WL-2H1100S
(in case of WLH2-j ,
WLG2-j )
WL-LDS
(LED)
Switches Without Lever
WLRCA2-LES, WLRCA2-LDS
WLRH2-LES, WLRH2-LDS, WLRG2-LES
WLRG2-LDS
WLRGCA2-LES, WLRGCA2-LDS
Airtight, Hermetic Seal, Low-temperature, Heat-res is tive, Corro-
s ion-proof, and Weather-res is tant Models
Using the general-purpose model, six types of environment-resistant models can be created to meet a variety of difficult operating conditions.
Select the model most appropriate to your operating environment.
Nomenclature Example
Airtight Built-in Switch
Hermetic SealModel
The lead wires are sealed to the Limit Switch with
resin, providing a hermetically sealed construction.
Sealed by the rubber boot
of the plunger
Filled with epoxy resin
Leads for molding
Sealed by the resin molded
into the case cover
Four, M4 ±terminal screws
Exclusive connector
29
WL
WL
Models
Type
Us age
Environment-res is tant cons truction
Appropriate
models
For use in locations
subject to splashes of
water and anti-coolant
WLj -55
Airtight seal
Uses the W-10FB3-55 Airtight Built-in Switch. (See note 2.)
All models except the
low-temperature and
heat-resistive models.
(See note 3.)
Hermetic seal
(molded terminals
and anti-coolant
models)
All models except the
low-temperature and
heat-resistive models.
(See note 4.)
WLj -139
General-
purpose
built-in
Connection lead wires:
Standard 5-m VCT (vi-
nyl cabtire cable) cable
attached. Finished di-
ameter: 11.5 mm,
4-core.
The case cover and
conduit opening are
molded from epoxy
resin. The cover cannot
be removed.
switch
Hermeti-
cally-
sealed
built-in
switch
Connection lead wires:
Standard 5-m VCT
cable, with high flexibil- ing are molded from
ity and good anti-oil
properties attached.
Finished diameter:
11.5 mm, 4-core.
The case cover, cover
box and conduit open-
WLj -140
WLj -141
WLj -RP40
epoxy resin. The cover
cannot be removed
(140, 141, RP40, and
RP60).
The Head opening is
protected from cutting
powder. (WLj -141)
The connector can be
removed, so it is pos-
sible to use flexible
wires in the cable.
WLj -RP60
WLj -TC
Rubber parts are made
from fluorine rubber.
Low-temperature
Heat-resistive
Can be used at a tem-
perature of --40_C (The
operating temperature
range is --40_C to
40_C), but cannot with-
stand icing.
Uses the general-purpose built-in switch.
All models except air-
tight, hermetic, heat-re-
sistive, corrosion-proof,
or lamp-equipped mo-
dels.
Silicone rubber is used for rubber parts such as the O-ring,
gasket, etc.
WLj -TH
Can be used in temper- Uses a special built-in switch made from heat-resistant resin.
All models except air-
tight, hermetic, low-
temperature, corrosion-
proof, lamp-equipped,
nylon roller
atures of 120_C (The
operating temperature
range is 5_C to
120_C).
Silicone rubber is used for rubber parts such as the O-ring,
gasket etc.
(WLCA2-26N), seal
roller models, and resin
rod (WLNJ-2) models.
WLj -RP
Corrosion-proof
For use in locations
subject to corrosive
gases and chemicals.
Diecast parts such as the switch box are made of corrosion-
proof aluminum.
All models except over-
travel model (-2N), fork
lever lock models
(WLCA32-41 to -43),
low-temperature, heat-
resistive, and lamp-
equipped models.
Rubber sealing parts are made of fluorine rubber which aids in
resisting oil, chemicals and adverse weather conditions.
Exposed nuts and screws (except the actuator section) are
made of stainless steel.
Moving and rotary parts such as rollers are made of sintered
stainless steel or stainless steel.
WLj -P1
Outdoor specifica-
tions
For use in parking lots
and other such outdoor tolerance to deterioration over time, and changes in tempera-
locations.
Rubber parts are made from silicone rubber, which has a high- Only the general-pur-
pose overtravel models
(WLH2/12), the over-
travel high-sensitivity
models (WLG2/12) and
some standard models
(e.g., WLCA2) can be
used. Excluding heat-
resistive models.
ture.
Rollers are made of stainless steel to improve corrosion resist-
ance.
Exposed nuts and screws are made of stainless steel.
Note: 1. Consult your OMRON representative for the microload WL01j models.
2. Use the SC Connector for the conduit opening.
3. The actuator can be created using the standard model.
4. The actuator can be created using the standard model. For WL-j 141, only WLG2, WLCA2, and WLGCA2 can be used.
30
WL
WL
Dimens ions /Operating Characteris tics
Approved Standard Ratings
The dimensions and operating characteristics are the same as gen-
eral-purpose, environment-resistant models.
Contact your OMRON representative for details of approved mod-
els.
Ratings /Characteris tics
See pages 7 to 10.
Ordering Information
Use the following as a guide when ordering environment-resistant
models.
Contact Form
E.g.: For a hermetic model of WLCA2
WLCA2 -
"
Standard
55
"
Specifications No.
(White)
(Blue)
An additional catalog is available foroutdoor specifications models.
(Black)
(Red)
Lamp-equipped Models
The operating status of the Switch can be checked using a neon
lamp of LED indictor.
The lamp-equipped models are ideal in locations using a conveyor
belt where items need to be checked, or locations that are difficult to
inspect for faults.
Circuit checks and troubleshooting errors are easy done.
Light-ON when Operating
LED at top
Light-emitting diode (LED)
Lamp holder
Contact spring
Operation
Indictor window
The built-in switch’s terminal screws are used to connect the lamp
terminal (indicator cover). Since the connection spring (coil spring)
is used for this connection, it will not be necessary to connect to the
lamp terminal. When a ground terminal is provided however, lead
wire method must be used.
Light-ON when Not Operating
LED at bottom
WL-LD has a built-in rectifier stack, so it will not be necessary to
change the polarity.
The indicator cover is molded from diecast aluminum and has out-
standing sealing properties. Furthermore, regardless of whether
the power is connected or not, the operating status is shown (oper-
ating or not operating), and indicators can be switched from
light-ON when operating and light-ON when not operating, by sim-
ply rotating the lamp holder by 180_. (Molded terminals do not have
this switching capacity.)
Models /Ratings
Operating
characteris tics
Rated voltage
Leakage current
Approx. 0.6 mA
Lamp-equipped Switch
Lamp-equipped cover
only
Neon lamp
WLj -LE (see note 1.)
WL-LE
125 VAC
250 VAC
Approx. 1.9 mA
Approx. 1 mA
LED
10 to 115 VAC/VDC
WLj -LD (see note 1.)
WL-LD
Note: 1. In the model number, j
indicates the actuator number. For example, CA2, D, NJ, etc.
2. The default setting is “light-ON when not operating.” Turn the lamp holder by 180_ to change the setting to “light-ON when operat-
ing.”
31
WL
WL
Operation
LIght-ON when operating
(See note 1.)
WL-LE
WL-LD
Power supply
Built-in switch
Load
Internal circuit
Light-ON when not operating
(See note 2.)
WL-LE
WL-LD
Power supply
Internal circuit
Load
Built-in switch
Note: 1. Light-ONwhen operating means that the lamp lights when the Limit Switch contacts (NC) release, or when the actuatorrotates oris
pushed down.
2. Light-ON when not operating means the lamp remains lit when the actuator is free, or when the Limit Switch contacts (NO) close
when the actuator rotates or is pushed down.
Ordering Information
When ordering general-purpose indicator-equipped models insert the specifications number at the end of the basic model number.
E.g.: When a neon lamp is installed in a General-purpose/Standard Roller Lever Switch (WLCA2).
WLCA2
"
Standard
LE
"
Lamp
specifications
When ordering indicator-equipped molded terminal models, insert the specifications number at the end of the standard model number.
E.g.: When a Neon Lamp (WL-LE) is installed in a general-purpose molded terminal model (WLCA2-139).
WLCA2-139 LE
2
"
"
"
Standard
Lamp
specifications wiring
Lamp
2: NC connection: Light-ON when operating
3: NO connection: Light-ON when not operating
Note: The indicator cover cannot be replaced on the molded terminals. In all cases the indicator does not light when the load is ON.
Dimens ions /Operating Characteris tics
Roller Lever
WLCA2-LE
60 max.
17.5 dia. × 7
Stainless steel roller
Four, M3.5
M5 × 12
Note: Unless otherwise indicated, a tolerance of ±0.4 mm applies
Allen-head
to all dimensions.
bolt
holes
Four,
+0.2
0
OF max.
RF min.
PT
13.34 N
2.23 N
15°±5°
30°
5.2
dia. holes
Three, M4 × 13
OT min.
MD max.
Four, M6
Depth: 15 min
JIS B0202 G1/2
Effective thread:
4 threads min.
12°
42 max.
Note: Stainless steel roller
32
WL
WL
Internal Circuits
WL-LE
Neon lamp
WL-LD
Rectifier stack
Contact
spring
Contact
spring
Resist-
ance
Rated current
diode
Zener
diode
Light-emitting
diode (LED)
Resistance
33
WL
WL
Sensor I/O Connector Models
A reduction in the amount of wiring and parts makes maintenance easy and reduced wiring mistakes, in addition it’s already compact size for
fitting into areas of limited space.
Ordering Information
Item
Standard
Overtravel
High s ens itivity
Yes
---
Actuators
Load
Rotating lever
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---
Plunger
Standard load (SPST-NO/SPST-NC)
Microload (SPST-NO/SPST-NC)
High-precision models WL-j 55
Spatter-prevention models (See note 3.)
Lamp
Note: 1. Standard Models: For standard models only one-side operation at an angle of 45_ is possible.
Overtravel Models: Only one-side operation at an angle of 80_ is possible. One-side operation only is not possible.
High-precision Models: Only one-side operation at an angle of 45_ is possible, and pretravel (PT) is 5_, as opposed to 15_ for stan-
dard models.
2. For information other than that listed at the above, contact your OMRON representative.
3. The spatter-prevention models are only available as pre-wired connectors.
Models
Direct-wired Connectors
Note: 1. In the model number, j indicates the actuator number.
Type
Lamp-equipped
Double-seal
2-core (NO)
4-core
WLj -LDK43
WLj -55LDK43
For example, Overtravel Model WLG2-LDK13.
WLj -LDK13
2. The lamp is set to “light-ON when not operating” (NO
connection).
WLj -55LDK13
Pre-wired Connectors
Type
Lamp-equipped
Double-seal
2-core (NO)
WLj -LD-M1J
WLj -55LD-M1J
2-core (NC)
WLj -LD-M1JB
WLj -55LD-M1JB
4-core
WLj -LD-DGJ03
WLj -55LD-DGJ3
3-core (NO)
WLj -LD-DK1EJ03
WLj -55LD-DK1EJ03
Note: 1. In the model number, j
indicates the actuator number. For example, Overtravel Model WLG2-LD-M1J.
2. The lamp is set to “light-ON when not operating” (NO connection).
Model Number Legend
WL -
-
LD
1
2
3
4
1. Electrical Rating
Blank: Standard
4. Wiring Specifications
K13A:
Direct-wired Connector
01:
Microload
(2-core: AC, NO wiring, connector pins No. 3, 4)
Direct-wired Connector
(2-core: DC, NO wiring, connector pins No. 3, 4)
Direct-wired Connector (4-core: AC)
Direct-wired Connector (4-core: DC)
Pre-wired Connector*
(2-core: DC, NO wiring, connector pins No. 3, 4)
Pre-wired Connector*
(2-core: DC, NO wiring, connector pins No. 1, 4)
Pre-wired Connector*
K13:
2. Actuator Type
CA2: Roller lever: Standard
GCA2:Roller lever: High-precision
H2:
G2:
D2:
K43A:
K43:
-M1J:
Roller lever: Overtravel, general-purpose
Roller lever: Overtravel, high-sensitivity
Plunger: Top-roller plunger
-M1GJ:
-M1JB:
D28: Plunger: Top-roller plunger, sealed
3. Built-in Switch Type
Blank: Standard
55:
(2-core: DC, NC wiring, connector pins No. 3, 2)
Pre-wired Connector* (4-core, AC)
Pre-wired Connector* (4-core, DC)
Hermetically sealed
-AGJ03:
-DGJ03:
-DK1EJ03: Pre-wired Connector*
(3-core: DC, NO wiring, connector pins No. 2, 3, 4)
Note: *With 0.3-m cable attached.
34
WL
WL
Pre-wired Connector
Direct-wired Connector
Spatter-prevention Models
WL -
-
S
1
2
3
4
5
1. Electrical Rating
Blank: Standard
4. Indicator Lamp
Blank: None
01:
2. Actuator Type
CA2: Roller lever: Standard
GCA2:Roller lever: High-precision
Microload
LD:
LE:
LED indicator lamp (AC/DC common)
Neon Lamp
5. Wiring Specifications
-M1J-1: Pre-wired Connector*
(2-core: DC, NO wiring, connector pins No. 3, 4)
-M1GJ-1: Pre-wired Connector*
(2-core: DC, NO wiring, connector pins No. 1, 4)
H2:
G2:
Roller lever: Overtravel, general-purpose
Roller lever: Overtravel, high-sensitivity
D28: Plunger: Top-roller plunger, sealed
-DGJS03: Pre-wired Connector* (4 core, DC)
3. Built-in Switch Type
Blank: Standard
Note: *With 0.3-m cable attached.
55:
Hermetically sealed
Wiring Specifications
Direct-wired Connector
Pre-wired Connector
4-core
2-core
4-core
2-core
M1GJ (DC)
3-core
K13 (DC)
K13A (AC)
K43 (DC)
K43A (AC)
M1J (DC)
M1J B (DC)
DGJ 03 (DC)
AGJ 03 (AC)
DK1EJ 03 (DC)
Connector
Connector
Connector
Connector
Connector
Connector
Connector
Built-in
s witch
Built-in
s witch
Built-in
Built-in
s witch
Built-in
s witch
Built-in
Built-in
s witch
1 (NC)
2 (NC)
3 (NO)
4 (NO)
s witch
1 (NC)
2 (NC)
s witch
1 (NC)
2 (NC)
3 (NO)
4 (NO)
1 (NC) ---
2 (NC) ---
1
2
3
4
1 (NC) ---
2 (NC) ---
1 (NC) ---
2 (NC) ---
3
2
1
2
3
4
1 (NC) ---
2 (NC)
3 (NO)
4 (NO)
2
3
4
3 (NO)
4 (NO)
3
4
3 (NO)
4 (NO)
3
4
3 (NO)
4 (NO)
1
4
3 (NO) ---
4 (NO) ---
35
WL
WL
Ratings
General-purpos e Ratings (Lamp-equipped)
Non-inductive load
Res is tive load Lamp load
NC NO NC NO
Indcutive load
Inductive load
NC NO
Type
Rated
voltage
Motor load
NC NO
For DC
12 VDC
24 VDC
48 VDC
115 VDC
115 VAC
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
1 A
0.8 A
1 A
0.8 A
1 A
0.2 A
1 A
0.2 A
1 A
0.8 A
1 A
0.8 A
1 A
0.2 A
1 A
0.2 A
1 A
For AC
Note: 1. The above figures are for standard currents.
2. Inductive loads have a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
4. Motor load has an inrush current of 6 times the steady-state current.
Dimens ions
Roller Lever Models
Standard Model (WLCA2), High-precis ion Model (WLGCA2), Overtravel Model (WLH2), and Overtravel High-s ens itivity Model
(WLG2)
Note: 1. For the WLG2 model, only the dimensions for the set position marker plate change.
2. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
3. The above diagram is for a lamp-equipped model.
Direct-wired Connector Models
Pre-wired Connector Models
60 max.
60 max.
17.5 dia. x 7
(see note)
17.5 dia. x 7
(see note)
Four,, M3.5
Four, M3.5
M5 x 12 Allen-
head bolt
M5 x 12 Allen-
head bolt
Four,
Four,
+0.2
+0.2
0
5.2
dia. holes
0
5.2
dia. holes
Three, M4 x 13
Three, M4 x 13
Four, M6
Depth: 15 min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
SC-1M
42 max.
Note: Stainless sintered roller
XS2H-D421
42 max.
Operating
characteris tics
Roller lever/Standard
model
Roller lever/High
precis ion model
Roller lever/Overtravel Roller lever/Overtravel
model
high s ens itivity model
Operating force: OF
max.
13.34 N
13.34 N
9.81 N
9.81 N
Release force: RF min.
Pretravel: PT
2.23 N
1.47 N
0.98 N
0.98 N
°
°
°
°
+2
-- 0
+2
-- 1
15±5°
15±5°
5°
10°
Overtravel: OT min.
30°
12°
40°
3°
55°
12°
65°
7°
Movement differential:
MD max.
36
WL
WL
Top-roller Plunger
WLD2
Note: 1. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
2. The above diagram is for a lamp-equipped model.
Direct-wired Connector Models
Pre-wired Connector Models
17 dia. x 5
(see note)
17 dia. x 5
(see note)
Four, M3.5 × 10
Four, M3.5 × 10
Four,
Four,
+0.2
+0.2
5.2
5.2
dia. holes
0
dia. holes
0
Three, M4 x 13
Three, M4 x 13
Four, M6
Depth: 15 min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
SC-1M
42 max.
Note: Stainless sintered roller
XS2H-D421
42 max.
Operating characteris tics
Top-roller plunger
actuator
Operating force: OF max.
Release force: RF min.
Pretravel: PT max.
26.67 N
8.92 N
1.7 mm
5.6 mm
Overtravel: OT min.
Movement differential: MD max. 1 mm
Operating position: OP
44±0.8 mm
39.5 mm
Total travel position: TTP max.
37
WL
WL
Sealed Top-roller Plunger
WLD28
Note: 1. Unless otherwise indicated, a tolerance of ±0.4 mm applies to all dimensions.
2. The above diagram is for a lamp-equipped model.
Direct-wired Connector Models
Pre-wired Connector Models
11.2 dia. x 5
(see note)
11.2 dia. x 5
(see note)
Four, M3.5 x 10
Four, M3.5 x 10
Four,
Four,
+0.2
+0.2
5.2
dia. holes
0
5.2
dia. holes
0
Three, M4 x 13
Three, M4 x 13
Four, M6
Depth: 15 min.
Four, M6
Depth: 15 min.
JIS B0202 G1/2
Effective thread:
4 threads min.
SC-1M
42 max.
Note: Stainless sintered roller
XS2H-D421
42 max.
Operating characteris tics
Sealed top-roller plunger
actuator
Operating force: OF max.
Release force: RF min.
Pretravel: PT max.
16.67 N
4.41 N
1.7 mm
5.6 mm
Overtravel: OT min.
Movement differential: MD max. 1 mm
Operating position: OP
44±0.8 mm
39.5 mm
Total travel position: TTP max.
38
WL
WL
Application Variations
Item
Appropriate model/actuator
Details
Changing the ins tallation pos ition Roller Levers: WLCA2, WL01CA2,
of the actuator
WLH2, WL01H2, WLG2, WL01G2
Adjustable Roller Levers: WLCA12,
By loosening the Allen-head bolt on
Loosen the M5 × 12 bolt, set the
actuator’s position and then tighten
the bolt again.
the actuator lever, the position of the WL01CA12, WLH12, WL01H12,
actuator can be set anywhere within WLG12, WL01G12
the 360_. With Lamp-equipped
Adjustable Rod Levers: WLCL,
Switches, the actuator lever comes
WL01CL, WLHL, WL01HL, WLGL,
in contact with the top of the lamp
WL01GL
cover, so use caution when rotating
and setting the lever. When the lever
only moves forwards and backwards,
it will not contact the lamp cover.
Changing the orientation of the
Head
Roller Levers: WLCAj , WL01CAj ,
WLGCAj
Head
Loosen the screws.
Head
Loosen
the
screws.
By removing the screws in the four
corners of the Head, the Head can
be set in any of the four directions.
Be sure to change the plunger for
internal operations at the same time.
(The operational plunger does not
need to be changed on overtravel
general-purpose and high-sensitivity
models.) The roller plunger can be
set in either two positions at 90_.
WLCA2-2N and WL01CA2-2N can
only be set in either the forward or
backward direction.
Adjustable Rod Levers: WLCL,
WL01CL
Horizontal Plungers: WLSDj ,
WL01SDj
Roller Plungers: WLD2, WL01D2
Sealed Roller Plungers: WLD28,
WL01D28.
Note: Does not include -RP60
Series or -141 Series.
Changing the operating direction
Roller Levers: WLCAj , WL01CAj
The output of the
The output of the
Switch will be changed,
regardless of which
direction the lever is
pushed.
Switch will only be
changed when the lever
is pushed in one
direction.
By removing the Head on models
which can operate on one-side only, WL01CA12
and then changing the direction of
Adjustable Roller Levers: WLCA12,
Adjustable Rod Levers: WLCL,
WL01CL
the operational plunger, one of three
operating directions can be selected.
In the case of overtravel models, as
noted on page 20, by loosening the
rubber holder using either a coin or a
flat-blade screwdriver, and changing
the direction of the internal rubber
section, one of three operating
Operating
Not operating
Operating
Operating
Operating
Not operating
Overtravel Models: WLCAj -2N,
WL01CAj -2N
Note: The diagram at the right is not
correct for the overtravel -2N
models.
Operational
plunger
directions can be selected.
The tightening torque for the screws
on the Head is 0.78 to 0.88 N S m. (8
Operation in
both directions
Clockwise operation
Counterclockwise
operation
to 9 kg
S cm)
For details on overtravel -2N models, refer to page 19.
Ins talling the roller on the ins ide
Roller Levers: WLCAj , WL01CAj ,
except for the adjustable roller
levers.
By installing the roller lever in the
opposite direction, the roller can be
installed on the inside. (Set so that
operation can be completed within a
180_ level range.)
Fork Lever Locks: WLCA32-4j ,
WL01CA32-4j
Loosen th
Allen-hea
39
WL
WL
Item
Appropriate model/actuator
Details
Selecting the roller pos ition
Fork Lever Locks: WLCA32-4j ,
WL01CA32-4j
WLCA32-41
WLCA32-42
WLCA32-43
WLCA32-44
There are four types of fork lever
lock for use depending on the roller
position.
Adjus ting the length of the rod or
lever
Adjustable Roller Levers: WLCA12,
WL01CA12 etc.
WLCA12 etc.
The length of the rod or lever can be Adjustable Rod Levers: WLCL,
adjusted by loosening the Allen-head WL01CL etc.
bolt.
Adjustment range:
25 to 89 mm
Loosen this
Allen-head
bolt and
Loosen this
Allen-head
bolt and
adjust the
length of
the lever.
adjust the
length of
the rod.
40
WL
WL
Precautions
Cautions
Built-in Switch
When a rod or wired-type actuator is used, do not touch the top end
of the actuator. Doing so may result in injury.
Applicable models: WLHAL5 and WL01HAL5 Rod Spring Levers
and WLNJ-S2 and WL01NJ-S2 Steel-wire Actuators.
Do not remove or replace the built-in switch. If the position of the
built-in switch moves, it can cause reduced performance, and if the
insulation sheet moves (separator), the insulation may become in-
effective.
Correct Us e
Correct Tightening Torque
If screws are too loose they can lead to an early malfunction of the
Switch, so ensure that all screws are tightened using the correct
torque.
A short-circuit may cause damage to the Switch, so insert a circuit
breaker fuse, of 1.5 to 2 times the rated current, in parallel with the
Switch. In order to meet EN approval ratings, use a 10-A fuse that
corresponds to IEC269, either a gI or gG.
No.
Type
Torque
0.78 to 0.88 N S m
1.18 to 1.37 N S m
4.90 to 5.88 N S m
When wiring terminal screws, use M4 round crimp terminals and
tighten screws to the recommended torque. Wiring with broken
wires, or the incorrect crimp terminals, or not tightening screws to
the recommended torque can lead to short-circuits, leakage cur-
rent, and fire.
A
B
C
Head mounting screw
Cover mounting screw
Allen-head bolt (for
securing the lever)
When performing internal wiring there is a chance of short-circuit,
leakage current, or fire, so be sure to protect the inside of the Switch
from splashes of oil or water, corrosive gases, and cutting powder.
D
E
F
Terminal screw
Connector
0.59 to 0.78 N S m
1.77 to 2.16 N S m
4.90 to 5.88 N S m
Using an inappropriate connector or assembling Switches incor-
rectly (assembly, tightening torque) can result in malfunction, leak-
age current, or fire, so be sure to read the instruction manual thor-
oughly beforehand.
Main Unit screws
Even when the connector is assembled and set correctly, the end of
the cable and the inside of the Switch may come in contact. This can
lead to malfunction, leakage current, orfire, so be sure to protect the
end of the cable from splashes of oil or water and corrosive gases.
Environmental Precautions
When the Switch is used in locations subject to splashes of water or
oil, the material of the seal, which ensures the sealing properties of
the Switch, may undergo changes in shape and quality. This is due
to deterioration (including expansion and contraction), and may re-
sult in reduced performance, ineffective return, and ineffective seal-
ing (leading to ineffective contact, insulation, leakage current, and
fire). Confirm the possible effects of the operating environment on
the Switch before use.
In particular, when changing the direction of the Head, make sure
that all screws are tightened again to the correct torque. Do not al-
low foreign objects to fall into the Switch.
Ins talling the Switch
To installthe Switch, make a mounting panel, as shown in the follow-
ing diagram, and tighten screws using the correct torque.
Standard/Overtravel model
Overtravel model (s ide
ins tallation)
Mounting holes
Mounting holes
+0.2
0
+0.2
0
Four,
Two,
5.2
5.2
dia. holes
dia. holes
41
WL
WL
Connectors
Rotating Lever Set Pos ition
Either the easy-to-use Allen-head nut or the SC Connector can be
used as connectors. To ensure high-sealing properties, use the SC
Connector. (Refer to pages NO TAG to NO TAG.) (SC-1M to -5M
and others.)
All rotating lever models, except the fork lever lock, have a set posi-
tion marker plate. (See page 7.) After operation, set the indicator
needle on the marker plate so that is in the convex section of the
bearing.
Wiring
Terminal Plate
Use 1.25-mm lead wires and M4-insulation covered crimp terminals
for wiring.
By using a short circuit plate, as shown in the following diagram, the
Switch can be fabricated into a single-polarity double-break model.
When ordering specify WL Terminal Plate (product code:
WL-9662F).
Crimp Terminal External Dimens ions
D dia.
dz dia. 4.3
D dia. 4.5
dz dia.
B:
L:
F:
ℓ:
8.5
21.0
7.8
9.0 (mm)
pper plate
Wiring Method
Switch Box Section
Ground terminal
NO terminal
NC terminal
Note: The ground terminal is only installed on models with ground
terminals.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. C001-E1-12
42
相关型号:
©2020 ICPDF网 联系我们和版权申明