Z-15GW2555-B 概述
Snap Acting/Limit Switch, 快动/限位开关
Z-15GW2555-B 规格参数
生命周期: | Obsolete | Reach Compliance Code: | unknown |
风险等级: | 5.75 | 开关类型: | SNAP ACTING/LIMIT SWITCH |
Base Number Matches: | 1 |
Z-15GW2555-B 数据手册
通过下载Z-15GW2555-B数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载General-purpose Basic Switch
Z
CSM_Z_DS_E_4_4
Best-selling Basic Switch Boasting
High Precision and Wide Variety
• A large switching capacity of 15 A with high repeat accuracy.
• A wide range of variations in contact form for your selection: basic,
split-contact, maintained-contact, and adjustable contact gap types.
• A series of standard models for micro loads is available.
• A series of molded terminal-type models incorporating safety
terminal protective cover is available.
Be sure to read Safety Precautions on page 26 and Safety Precautions
for All Basic Switches.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Model Number Structure
Configuration
Refer to page 3.
Refer to page 5.
Basic models
General-purpose
Drip-proof
Without terminal protective cover
Refer to page 5.
Refer to page 2.
Refer to page 4.
Refer to page 4.
With terminal protective cover
Molded terminal
Split-contact models
General-purpose
General-purpose
Maintained-contact models
Basic Models
Split-contact Models
• This type is identical in construction to the general-purpose basic
switch except that it has two pairs of simultaneous acting contacts
by splitting moving contacts.
• Since the moving contacts are connected to a common terminal,
either parallel or series connection is possible.
• Highly reliable micro load switching is ensured if the model is used
as a twin-contact switch.
General-purpose
• A variety of actuators is available for a wide range of application.
• The contact mechanism of models for micro loads is a crossbar
type with gold-alloy contacts, which ensures highly reliable
operations for micro loads.
• Contact Gap:
H2: 0.20 mm (extra-high-sensitivity)
H: 0.25 mm (high-sensitivity, micro voltage current load)
G: 0.5 mm (standard)
E: 1.8 mm (high-capacity)
Maintained-contact Models
• The maintained-contact type has a reset button at the bottom of the
switch case, in addition to the pushbutton (plunger) located on the
opposite side of the reset button. Use these buttons alternately.
• Since the Switch has greater pretravel than overtravel, it is suitable
for use in reversible control circuits, manual reset circuits, safety
limit circuits, and other circuits which are not preferable for
automatic resetting. (For further details, refer to individual
datasheets.)
Drip-proof
• These Switches use a rubber boot on the actuator and adhesive fill
between the case and cover to increase resistance to drips.
• Models with drip-proof terminal protective covers and molded
terminals with resin filling are also available.
1
Z
Model Number Legend
Basic Models
Standard Models (Drip-proof Type/Molded Terminals)
Z-@@@@-@
Z-@55-M@@ @M
(1)(2)(3)(4) (5)
(1)
(2)(3) (4)
(1) Ratings
(1) Drip-proof Type
(2) Lead Outlets
None : VSF
01
15
: 0.1 A (micro load)
: 15 A
(2) Contact Gap
19
: VCT
H2
H
: 0.20 (extra-high-sensitivity)
: 0.25 mm (high-sensitivity,
micro load)
: 0.5 mm (standard)
: 1.8 mm (high-capacity)
(3) Directions of Lead
Outlets (See following
diagrams.)
L Type
D Type
R Type
G
E
L
: Left
(3) Actuator
R
D
: Right
: Descending
None : Pin plunger
(4) Length of Lead
Outlets
S
D
K
K3
Q3
Q
: Slim spring plunger
: Short spring plunger
: Spring plunger (medium OP)
: Spring plunger (high OP)
: Panel mount plunger (low OP)
: Panel mount plunger (medium
OP)
1
3
: 1 m
: 3 m
Split-contact Models
Maintained-contact Models
Q8
Q22
Q21
: Panel mount plunger (high OP)
: Panel mount roller plunger
: Panel mount cross roller
plunger
Z-10F@Y-B
Z-15-E@R
(1)(2)(3)(4) (5)
(1) (2)(3)(4)
(1) Ratings
(1) Ratings
L
L2
W21
W
W3
W32
W4
W44
W78
: Leaf spring (high OF)
: Roller leaf spring
: Short hinge lever
: Hinge lever (low OF)
: Hinge lever (medium OF)
: Hinge lever (high OF)
: Low-force hinge lever
: Long hinge lever
: Low-force wire hinge lever
(low OF)
: Low-force wire hinge lever
(high OF)
: Short hinge roller lever
: Hinge roller lever
: Hinge roller lever (large roller)
: Short hinge cross roller lever
: Hinge cross roller lever
10
: 10 A (split-contact models)
15
: 15 A
(2) Contact Gap
F
(3) Actuator
None : Pin plunger
S
D
Q
Q22
W
(2) Contact Gap
E
(3) Actuator
None : Pin plunger
S
W
: 1 mm (high-capacity)
: 1.8 mm (high capacity)
: Slim spring plunger
: Slim spring plunger
: Hinge lever
: Short spring plunger
: Panel mount plunger
: Panel mount roller plunger
: Hinge lever
: Short hinge roller lever
: Hinge roller lever
: Reverse short hinge roller
lever
(4) Structure
R
: Maintained-contact models
W52
W22
W2
M22
W22
W2
W25
W49
W54
(4) Construction
Y
: Split-contact models
(5) Terminals
W2277 : Unidirectional short hinge
roller lever (low OF)
B
: Screw terminal
(with toothed washer)
M
: Reverse hinge lever
: Reverse short hinge roller
lever
M22
M2
NJ
NJS
: Reverse hinge roller lever
: Flexible rod (high OF)
: Flexible rod (low OF)
(4) Degree of Protection
None : General-purpose
55
: Drip-proof
(not include the terminals)
: Drip-proof
A55
(including the terminals)
(5) Terminals
None : Solder terminal
B
: Screw terminal
(with toothed washer)
B5V
: Screw terminal with terminal
cover (for Z-15G@A55 only)
Note: For combinations of models, Ordering
Information on page 3 to 6.
2
Z
Ordering Information
Main Unit
Basic Models (General-purpose)
Extra-high
sensitivity
Classification
Standard
High-sensitivity
High-capacity
Micro load
Actuator
Contact gap
G (0.5 mm)
Model
H (0.25 mm)
Model
H2 (0.20 mm)
Model
E (1.8 mm)
Model
H (0.25 mm)
Model
Terminal *1
Pin plunger
Z-15G
Z-15H
Z-15H2
Z-15E
Z-01H
Z-15G-B
Z-15H-B
Z-15HS
Z-15H2-B
Z-15E-B
Z-01H-B
Z-01HS
Z-15GS
Slim spring plunger
---
---
---
Z-15GS-B
Z-15GD
Z-15HS-B
Z-15HD
Z-01HS-B
Z-01HD
Z-15ED
Short spring
plunger
Z-15GD-B
Z-15GQ3
Z-15HD-B
Z-15ED-B
Z-01HD-B
Low
OP
---
---
---
Panel mount
plunger
Z-15GQ3-B
Z-15GQ
Z-15HQ
Z-15EQ
Z-01HQ
Medium
OP
---
Z-15GQ-B
Z-15GQ8
Z-15HQ-B
Z-15EQ-B
Z-01HQ-B
High
OP
---
---
---
---
---
---
---
---
Z-15GQ8-B
Z-15GQ22
Z-15GQ22-B
Z-15GQ21
Z-15GQ21-B
Z-15GL
Z-15HQ22
Z-15HQ22-B
Z-15HQ21
Z-15EQ22
Z-15EQ22-B
Z-15EQ21
Panel mount roller
plunger
---
---
---
---
---
Panel mount cross
roller plunger
Z-15HQ21-B
Z-15EQ21-B
Leaf spring
---
---
---
---
---
---
Z-15GL-B
Z-15GL2
Roller leaf spring
Short hinge lever
Z-15GL2-B
Z-15GW21
Z-15GW21-B
Z-15GW
Z-15HW
Low
OP
Z-15GW-B
Z-15GW3
Z-15GW3-B
Z-15GW32
Z-15GW32-B
Z-15GW4
Z-15GW4-B
Z-15HW-B
Hinge lever
Medium
OP
---
---
---
---
High
OP
Z-15HW24
Z-15HW24-B
Z-15HW78
Low-force hinge
lever
---
---
---
---
---
---
Low
OP
Low-
Z-15HW78-B
Z-15HW52
forcewire
hinge
---
High
OP
lever
Z-15HW52-B
Z-15HW22
Z-15GW22
Z-15GW22-B
Z-15GW49
Z-15EW22
Z-01HW22
Short hinge roller
lever
---
---
Z-15HW22-B
Z-15EW22-B
Z-01HW22-B
Short hinge cross
roller lever
---
---
---
---
---
---
---
---
---
Z-15GW49-B
Z-15GW2
Z-15HW2
Stan-
dard
Hinge roller
lever
Z-15GW2-B
Z-15GW25
Z-15HW2-B
---
Large
roller
---
---
Z-15GW25-B
Z-15GW54
Hinge cross roller
lever
---
---
---
---
---
Z-15GW54-B
Z-15GW2277
Unidirectional
short hinge
roller lever
Parallel
---
---
---
---
---
---
---
---
---
---
---
---
Z-15GW2277-B
Z-15GM
Z-15GM-B
Z-15GM22
Reverse hinge lever *2
Reverse short
hinge roller lever
Reverse hinge
*2
Z-15GM22-B
Z-15GM2
roller lever *2
Z-15GM2-B
*1.
: Solder terminal
: Screw terminal
*2. The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers are freed by operating
the levers. Reverse-type models are highly vibration- and shock-resistive because the pin plungers are normally pressed.
3
Z
Minimum Order Lot
The following models are available at the minimum order lot specified below.
Orders must be placed per lot.
Classification
Minimum
order lot (pcs)
Standard
Z-15GD-B
High-sensitivity
---
Actuator
Short spring plunger
Z-15GQ
Z-15GQ-B
Z-15GQ8-B
---
---
Panel mount plunger
Z-15GQ22
Z-15GQ22-B
Panel mount roller plunger
Panel mount cross roller
plunger
Short hinge lever
Z-15GQ21-B
---
---
---
Z-15GW21-B
Z-15GW
Z-15GW-B
Hinge lever
10
Z-15GW4-B
---
Z-15HW24-B
Z-15HW78-B
Low-force hinge lever
Low-force hinge wire lever
Z-15GW22
Z-15GW22-B
Short hinge roller lever
Hinge roller lever
---
---
Z-15GW2
Z-15GW2-B
Reverse short hinge roller
lever
Z-15GM22-B
Z-15GM2-B
---
---
Reverse hinge roller lever
Split-contact Models
Maintained-contact Models
Actuator
Contact gap
Terminal
F (1.0 mm)
Model
Z-15ER
Actuator
*
1
Model
---
Pin plunger
Pin plunger
Z-10FY-B
---
Z-15ESR
Z-15EWR
Slim spring plunger
Hinge lever
Slim spring plunger
Short spring plunger
Z-10FSY-B
---
Z-10FDY-B
---
Panel mount plunger
Z-10FQY-B
---
Z-10FQ22Y-B
---
Panel mount roller
plunger
Hinge lever
Z-10FWY-B
---
Short hinge roller
lever
Z-10FW22Y-B
---
Hinge roller lever
Z-10FW2Y-B
---
Reverse short hinge
roller lever *2
Z-10FM22Y-B
*1.
: Solder terminal
: Screw terminal
*2. The pin plungers of reverse-type models are continuously pressed by the
actuator levers with compression coil springs and the pin plungers are freed
by operating the levers. Reverse-type models are highly vibration- and
shock-resistive because the pin plungers are normally pressed.
4
Z
Standard, Microload
Basic Models (Drip-proof Models
)
Classification
Standard
Micro load
Contact gap
G (0.5 mm)
H (0.25 mm)
Drip-proof terminal
protective cover
Not provided
Provided
Not provided
Terminal
*1
Model
Model
---
Model
Z-01H55
Actuator
Z-15G55
Pin plunger
Z-15G55-B
Z-15GD55
Z-15GD55-B
Z-15GK55
Z-15GK55-B
Z-15GK355
Z-15GK355-B
Z-15GQ55
Z-15GA55-B5V
Z-01H55-B
Z-01HD55
Z-01HD55-B
Short spring plunger
Spring plunger
---
---
Low
OP
---
---
---
---
Z-15GK3A55-B5V
---
High
OP
Panel mount plunger
Z-15GQ55-B
Z-15GQ2255
Z-15GQ2255-B
Z-15GQA55-B5V
---
Panel mount roller
plunger
---
Z-15GQ22A55-B5V
---
---
Panel mount cross
roller plunger
---
---
---
---
---
---
Z-15GQ2155-B
Z-15GL55
Z-15GQ21A55-B5V
Leaf spring
---
---
---
Z-15GL55-B
Z-15GL255
Roller leaf spring
Short hinge lever
Long hinge lever
Hinge lever
Z-15GL255-B
Z-15GW2155
Z-15GW2155-B
Z-15GW4455
Z-15GW4455-B
Z-15GW55
---
Z-15GW44A55-B5V
---
Z-15GW55-B
Z-15GW2255
Z-15GW2255-B
Z-15GWA55-B5V
---
Z-01HW2255
Short hinge roller lever
Z-15GW22A55-B5V
Z-01HW2255-B
Z-15GW255
Z-15GW255-B
Z-15GW227755
---
Hinge roller lever
---
---
Z-15GW2A55-B5V
---
Unidirectional short
hinge roller lever
Z-15GW227755-B
Z-15GM55
Z-15GW2277A55-B5V
Reverse hinge lever
Reverse short hinge
*2
---
---
---
---
---
---
Z-15GM55-B
Z-15GM2255
Z-15GM2255-B
Z-15GM255
roller lever
*2
Reverse hinge roller
lever
*2
Z-15GM255-B
Z-15GNJ55
Flexible rod (coil spring)
*3
---
---
Z-15GNJ55-B
*1.
: Solder terminal
: Screw terminal
*2. The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers are freed by operating
the levers.
*3. The tip is made of resin.
Classification
Contact gap
Standard
G (0.5 mm)
Minimum order
lot (pcs)
Minimum Order Lot
Actuator
The following models are available at the minimum order lot specified
below.
Orders must be placed per lot.
Short spring plunger
Spring plunger
Z-15GD55-B
Z-15GK55-B
Z-15GW4455-B
Z-15GW55
Hinge lever
Z-15GW55-B
Z-15GW2255
Z-15GW2255-B
Z-15GW255-B
Z-15GNJ55-B
10
Short hinge roller lever
Hinge roller lever
Flexible rod (coil spring)
5
Z
Basic Models (Drip-proof Models
)
Minimum Order Lot
High-sensitivity
The following models are available at the minimum order lot specified
below.
Orders must be placed per lot.
Classification
Contact gap
Drip-proof terminal protective cover
High-sensitivity
H (0.25 mm)
Not provided
Model
Classification High-sensitivity
Minimumorder
lot (pcs)
Actuator
Terminal *
Actuator
Contact gap
H (0.25 mm)
Z-15HNJS55
Flexible rod (steel wire)
Z-15HNJS55-B
10
Flexible rod
(steel wire)
Z-15HNJS55-B
*
: Solder terminal
: Screw terminal
Specifications
Ratings (Basic, Split-contact and Maintained contact Models)
Z-15 (Except Micro Load and Flexible Rod Models)
Z-01H
Item
Non-inductive load (A)
Resistive load Lamp load
Inductive load (A)
Inductive load Motor load
Resistive load (A)
NC NO
Rated voltage
Contact Rated
gap voltage
125 VAC
8 VDC
14 VDC
30 VDC
0.1
NC NO
15 (10) *
15 (10) *
10
NC
NO
NC NO
15 (10) *
15 (10) *
6
NC
NO
0.1
0.1
0.1
125 VAC
250 VAC
500 VAC *
3
2.5
1.5
1.5
1.25
0.75
5
3
1.5
2.5
1.5
0.75
G, H,
H2, E
8 VDC
15
15
6
0.5
0.25
3
3
3
0.5
0.25
1.5
1.5
1.5
0.5
0.25
15
10
5
0.05
0.03
5
5
5
0.05
0.03
2.5
2.5
2.5
0.05
0.03
14 VDC
30 VDC
125 VDC
250 VDC
Note: 1. The above current ratings are the values
of the steady-state current.
G
2. Inductive load has a power factor of 0.4
min. (AC) and a time constant of 7 ms
max. (DC).
3. Lamp load has an inrush current of 10
times the steady-state current.
4. Motor load has an inrush current of 6
times the steady-state current.
5. The normally closed and normally open
ratings of reverse hinge lever models are
opposite to each other.
6. The AC ratings of molded terminals are
125 and 250 V only.
7. The ratings values apply under the
following test conditions:
8 VDC
15
15
2
0.4
0.2
3
3
2
0.4
0.2
1.5
1.5
1.4
0.4
0.2
15
10
1
0.03
0.02
5
5
1
0.03
0.02
2.5
2.5
1
0.03
0.02
14 VDC
H, H2 30 VDC
125 VDC
250 VDC
8 VDC
14 VDC
30 VDC
125 VDC
250 VDC
15
15
15
0.75
0.3
3
3
3
0.75
0.3
1.5
1.5
1.5
0.75
0.3
15
15
10
0.4
0.2
5
5
5
0.4
0.2
2.5
2.5
2.5
0.4
0.2
E
(1) Ambient temperature: 20 2°C
(2) Ambient humidity: 65 5%RH
(3) Operating frequency: 20 operations/min
* Figures in parentheses are for the Z-15HW52, Z-15HW78(-B) and Z-15H2(-B) models, the AC ratings of
these models are 125 and 250 V only.
Z-15 (Flexible Rod Models)
Non-inductive load (A)
Resistive load Lamp load
NC NO
Inductive load (A)
Inductive load Motor load
NC NO
Rated voltage
Use the switch within the operating
range.
NC
NO
NC
NO
125 VAC
250 VAC
15
15
2
1
1
0.5
7
5
2.5
1.5
2
1
5 mW
800 mW
0.16 mA
26 mA
30
24
8 VDC
15
15
2
0.4
0.2
2
2
2
0.4
0.2
1
1
1
0.4
0.2
7
7
1
0.03
0.02
3
3
1
0.03
0.02
1.5
1.5
0.5
0.03
0.02
Standard
load area
Z-15H, H2
Z-15G
Z-15E
Z-10FY
Z-15ER
14 VDC
30 VDC
125 VDC
250 VDC
Micro load area
Z-01H
Z-10F
12
Item
Non-inductive load (A)
Resistive load Lamp load
Inductive load (A)
Unusable
Inductive load
Motor load
range
Contact
gap
Rated
voltage
5
0
NC NO
NC
NO
NC NO
NC
NO
1 mA
100 mA 160 mA
125 VAC
250 VAC
10
10
4
2.5
2
1.5
6
6
5
3
2.5
1.5
0.1
1
10
100
1,000
Series
connec-
tion
Current (mA)
30 VDC
125 VDC
250 VDC
10
1
0.6
4
1
0.6
2
1
0.6
6
0.1
0.05
6
0.1
0.05
3
0.1
0.05
Z-01H
Z-15@, Z-10FY
Minimum
applicable
load
125 VAC
250 VAC
6
6
3
2.5
1.5
1.25
4
4
4
2
2
1
5 VDC 1 mA 5 VDC 160 mA
Parallel
connec-
tion
30 VDC
125 VDC
250 VDC
6
0.6
0.3
4
0.6
0.3
2
0.6
0.3
4
0.1
0.05
6
0.1
0.05
3
0.1
0.05
6
Z
Certified Standard Ratings
Ask your OMRON representative for information on certified models.
UL/CSA (General ratings only)
TÜV (EN61058-1)
Rated
Model
Rated
Z-15H@
Z-15G@
Z-01H@
Model
Z-15
Z-10F
Z-01H
voltage
voltage
125 VAC
250 VAC
480 VAC
30 VDC
250 VAC
125 VAC
30 VDC
15 A
---
---
15 A
---
---
---
0.1 A
0.1 A
15A 1/8HP
15A 1/4HP
15A
---
0.5A
6A 1/10HP
6A 1/8HP
6A
---
0.6A
0.1A
---
---
0.1A
---
---
CCC (GB14048.5)
125 VDC
250 VDC
Rated
Model
0.25A
0.3A
Z-15H@
Z-15G@
Z-01H@
voltage
250 VAC
125 VAC
30 VDC
15 A
---
---
15 A
---
---
---
0.1 A
0.1 A
Characteristics
Classifica-
Z-15 (except micro
tion load and flexible rod)
Item
Z-01H
Z-15 (flexible rod)
Z-10F
Z-15H2
Operating speed
0.01 mm to 1 m/s *1
1 mm to 1 m/s
120 operations/min
0.1 mm to 1 m/s *1
240 operations/min
0.01 mm to 1 m/s
240 operations/min
Mechanical 240 operations/min
Operating
frequency
Electrical
20 operations/min
Insulation resistance
Contact resistance
100 MΩ min. (at 500 VDC)
15 mΩ
max. (initial value) 50 m
Ω
max. (initial value) 15 mΩ max. (initial value)
25 mΩ max. (initial value) 15 mΩ max. (initial value)
Between contacts of same polarity
Between contacts of same polarity
Contact gap G: 1,000 VAC, 50/60 Hz for 1
min
Between contacts of same
polarity
Contact gap F: 1,500 VAC,
Between contacts of
same polarity
600VAC, 50/60Hz for
Contact gap G: 1,000 VAC, 50/60 Hz for 1 min
Contact gap H: 600 VAC, 50/60 Hz for 1 min
Contact gap E: 1,500 VAC, 50/60 Hz for 1 min
Dielectric strength
Contact gap H: 600 VAC, 50/60 Hz for 1 min 50/60 Hz for 1 min
1min
Between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts 2,000 VAC, 50/60 Hz for 1 min
10 to 20 Hz, 1.5-mm double
Vibration
resistance
Malfunction 10 to 55 Hz, 1.5-mm double amplitude *5
10 to 55 Hz, 1.5-mm double amplitude *5
amplitude *5
Destruction 1,000 m/s2 max.
Malfunction 300 m/s2 max. *2 *5
Shock
resistance
50 m/s2 max. *5
300 m/s2 max. *3 *5
100 m/s2 max.
Contact gap G, H: 20,000,000 operations min.
Contact gap E: 300,000 operations
Contact gap G, H: 500,000 operations min.
Contact gap E: 100,000 operations min.
500,000 operations
min. *1
100,000 operations
min.
20,000,000operations
min.
500,000 operations
min.
Mechanical
Electrical
1,000,000 operations min.
Durability
100,000 operations min.
General-purpose IP00
Drip-proof Equivalent to IP62 (except terminals)
Degree of
protection
Degree of protection
against electric shock
Proof tracking index
(PTI)
Class I
175
General-purpose −25°C to 80°C (with no icing)
Drip-proof −15°C to 80°C (with no icing)
General-purpose 35% to 85%RH
Ambient operat-
ing temperature
Ambient operat-
ing humidity
Drip-proof 35% to 95%RH
Weight
Approx. 22 to 58 g
Approx. 42 to 48 g
Approx. 34 to 61 g
Approx. 22 g
*1. The values are for the plunger models. (For the lever models, the values are at the plunger section.) (Consult your OMRON representative for other models.)
*2. The values are for the Z-15G pin plunger.
*3. The values are for the Z-10FY-B.
*4. The values are for the pin plunger. The durability for models other than the pin plunger is 10,000,000 min.
*5. Malfunction: 1 ms max.
Contacts Specification
Item
Classification
Z-15
Rivet
Z-01H
Single crossbar
Gold alloy
Z-10F
Rivet
Shape
Contacts
Material
NC
Silver
Silver
30 A max.
15 A max.
0.1 A max.
0.1 A max.
40 A max.
20 A max.
Inrush current
NO
Engineering Data
Mechanical Durability (Z-15G)
Electrical Durability (Z-15G)
10,000
5,000
Ambient temperature: 20 2°C
Ambient temperature: 20 2°C
Ambient humidity: 65 5%RH
3,000
Ambient humidity: 65 5%RH
5,000
3,000
Without load
Operating frequency: 240 operations/min
Operating frequency: 20 operations/min.
125 VAC cos dia. = 1
125 VAC cos dia. = 0.4
1,000
500
300
250 VAC cos dia. = 1
250 VAC
cos dia. = 0.4
1,000
100
500
300
50
30
500 VAC cos dia. = 1
500 VAC cos dia. = 0.4
100
10
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Overtravel (mm)
0
2
4
6
8
10 12 14 16
Switching Current (A)
7
Z
Structure
Basic Models
Split-contact Models
Contact Form (SPDT)
Contact Form
NC
COM
NC
NO
COM
NO
NC
NO
Note: The Z-15GM is a reversible model and the NO and NC positions are
reversed.
Note: The NO and NC terminal arrangement is reversed for Models with
reverse operation (Z-10FM).
Molded Terminals
COM (Black)
(Red) NC
(White) NO
Connection Example
Series Connection
Parallel Connection
( ) indicates wire color.
Note: The Z-15GM is a reversible model and the NO and NC positions are
reversed.
Structure
Drip-proof Construction
• Without Terminal Protective Cover
Rubber boot
Fixed contact (b)
Glued surface
(adhesive is
Movable spring
filled between
case and cover)
Maintained-contact Models
Contact Form
Movable contact
COM
NC
NO
Spring pivot
Fixed contact (a)
• With Terminal Protective Cover
Rubber boot (weather-resistive
chloroprene is used)
Pushbutton for resetting
Stainless-steel stopper
(improves sealing)
Rubber packing (improves
sealing between switch
housing and terminal cover)
Terminal protective covers are sold separately
for maintenance purposes, which can be,
however, used with the Z-
For details, refer to page 22.
@-B5V models only.
8
Z
Dimensions
(Unit: mm)
Mounting
Use M4 screws with plane washers and spring washers to mount the
Switch. Tighten each mounting screw securely to a torque of 1.18 to
1.47 N·m.
When mounting the Switch to a panel, use a tightening torque of 2.94
to 4.9 N·m for the hexagonal nuts on the actuator.
Panel Mount Plunger
Panel Mount Roller Plunger
12.5+0.2dia.
Two, 4.2 dia. mounting holes or M4
12.5+0.2 dia.
0
0
5+0.2
0
0.1
25.4
13+0.2
0
General-purpose
Basic Models
and Split-contact Models
Terminals
Basic Models
Split-contact Models
Screw Terminals (-B)
Solder Terminal (-A) (“-A” is not included
in the model numbers.)
Screw Terminals (Y-B)
5.6
6.4
9.2
11.9
0.1
25.4
11.9
0.2
17.45
20
20
23
17.1
0.2
17.45
0.2
17.45
3
Five, M3.5 × 5.5
terminal screws
(with toothed
washer)
COM
1
NO
NC
2
1
NO
COM
NC
Three, M4 × 5.5
Terminal screws
(with toothed
washer)
2
3
Appropriate terminal screw tightening torque: 0.49
to 0.78 N·m.
Note: With reverse action models (Z-10FM), the
49.2
49.2
Appropriate terminal screw tightening torque: 0.78
to 1.18 N·m.
positions of NO and NC terminals are
Note: With reverse action models (Z-15GM), the positions of NO and NC terminals are reversed.
reversed.
Dimensions and Operating Characteristics
The models, illustrations, and graphics are for screw-terminal models (-B). The “-A” at the end of the model number for solder terminal models has been omitted. For
details of the terminals, see above.
Pin Plunger
2.3 dia.
+0.075
-0.025
PT
0.25
23.3
4.2
dia. hole
Z-15G-B
Z-15H2-B
Z-15H-B
Z-15E-B
Z-01H-B
Z-10FY-B
2.3SR *
OP
24.2
9.2
+0.075
-0.025
4.2
+0.1
-0.05
4.36
dia.
0.2
17.45
11.9
0.1
25.4
* Stainless-steel plunger
49.2
Operating
Characteristics
Model
OF
RF min.
PT max.
OT min.
Z-15G-B
Z-15H2-B
Z-15H-B
Z-15E-B
Z-01H-B
Z-10FY-B
Operating force
Release force
Pretravel
Overtravel
Movement Differential MD max.
2.45 to 3.43 N
1.12 N
0.4 mm
0.13 mm
0.05 mm
1.96 to 2.5 N
1.12 N
0.3 mm
0.13 mm
0.005 to 0.008 mm
1.96 to 2.75 N 6.12 to 7.85 N
2.45 N max.
0.78 N
0.5 mm
0.13 mm
0.04 mm
4.46 to 7.26 N
1.12 N
0.8 mm
0.13 mm
0.1 mm
1.12 N
0.3 mm
0.13 mm
0.025 mm
1.12 N
0.8 mm
0.13 mm
0.13 mm
Operating Position OP
15.9 0.4 mm
5.2 dia.
4 dia.
Slim Spring Plunger
PT
0.25
23.3
*
Z-15GS-B
Z-15HS-B
Z-01HS-B
Z-10FSY-B
+0.075
-0.025
4.2
dia. hole
OP
9 dia.
24.2
9.2
+0.075
-0.025
4.2
+0.1
-0.05
4.36
dia.
0.2
17.45
11.9
0.1
25.4
* Stainless-steel plunger (flat, 1R chamfered)
49.2
Z-15GS-B
Z-15HS-B
Z-01HS
Z-10FSY-B
OF
2.45 to 3.43 N
1.12 N
0.4 mm
1.6 mm
0.05 mm
1.96 to 2.79 N
1.12 N
0.3 mm
1.6 mm
0.025 mm
2.45 N max.
0.78 N
0.5 mm
1.6 mm
0.05 mm
4.46 to 7.26 N
1.12 N
RF min.
PT max.
OT min.
MD max.
0.8 mm
1.6 mm
0.1 mm
OP
28.2 0.5 mm
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
9
Z
Short Spring Plunger
12.3 dia.
10 dia.
Z-15GD-B
Z-15HD-B
Z-15ED-B
Z-01HD-B
Z-10FDY-B
0.25
23.3
PT
7.15 dia.
12SR *
+0.075
-0.025
4.2
dia. hole
OP
24.2
9.2
+0.075
-0.025
4.2
+0.1
-0.05
4.36
dia.
0.2
17.45
11.9
0.1
25.4
* Plated iron plunger
49.2
Z-15GD-B
Z-15HD-B
Z-15ED-B
Z-01HD-B
Z-10FDY-B
OF
2.45 to 3.43 N
1.12 N
0.4 mm
1.6 mm
0.05 mm
1.96 to 2.79 N
1.12 N
0.3 mm
1.6 mm
0.025 mm
6.13 to 7.85 N
1.12 N
0.8 mm
1.6 mm
0.13 mm
2.45 N max.
0.78 N
0.5 mm
1.6 mm
0.05 mm
4.46 to 7.26 N
1.12 N
RF min.
PT max.
OT min.
MD max.
0.8 mm
1.6 mm
0.1 mm
OP
21.5 0.5 mm
Panel Mount Plunger
8.35 dia.
0.25
23.3
Note: 1. Do not use the M12 mounting screw
and the case mounting hole at the
same time, or excessive pulling force
will be imposed on the switch and the
case and cover may be damaged.
2. On the model Z-15GQ3-B, PT can be
set to a value larger than that for the Z-
15GQ.
PT
Z-15GQ-B
Z-15HQ-B
Z-15EQ-B
Z-15GQ8-B *
Z-01HQ-B
Z-10FQY-B
Z-15GQ3-B *
11.9SR
*1
M12 × 1
mounting screw
*2
OP
13.1
16.3
+0.075
-0.025
4.2
dia. hole
*3
*4
16 dia.
3. On the model Z-15GQ8-B, operating
position can be adjusted by providing a
screw in the plunger section.
4. On the model Z-15GQ8-B, the M3 hole
with a depth of 10 mm is a through
hole. Take precautions so that no
water or screw lock agent penetrates
into the hole.
9.2
4.2+0.075
-0.025
+0.1
4.36
dia.
-0.05
0.2
17.45
*1. Stainless-steel plunger
*2. Two hexagonal nuts (2 t
11.9
* The external
dimensions of the
actuator vary.
0.1
25.4
×
14 width across flats)
49.2
*3. Two lock nuts (2 t × 15.6 width across flats)
*4. Incomplete screw part with a maximum length
of 1.5 mm.
Z-15GQ-B
Z-15HQ-B
Z-15EQ-B
Z-01HQ-B
Z-10FQY-B
Z-15GQ3-B
Z-15GQ8-B
OF
2.45 to 3.43 N
1.12 N
0.4 mm
5.5 mm
0.05 mm
1.96 to 2.79 N
1.12 N
0.3 mm
5.5 mm
0.025 mm
6.13 to 7.85 N
1.12 N
0.8 mm
5.5 mm
0.13 mm
2.45 N max.
0.78 N
0.5 mm
5.5 mm
0.05 mm
4.46 to 7.26 N
1.12 N
2.45 to 3.43 N
1.12 N
2.45 to 3.43 N
1.12 N
0.5 mm
5.5 mm
0.05 mm
RF min.
PT max.
OT min.
MD max.
0.8 mm
5.5 mm
0.1 mm
4.2 mm
2.5 mm
2.2 mm
OP
21.8 0.8 mm
18.8 0.8 mm
32.5 1 mm
Panel Mount Roller Plunger
Z-15GQ22-B Z-15EQ22-B
Z-15HQ22-B Z-10FQ22Y-B
0.25
23.3
12.7 dia. × 4.8 *1
PT
*2
OP
15.5
M12 × 1
mounting
screw
+0.075
-0.025
4.2
dia. hole
Note: Do not use the M12 mounting screw and
the case mounting hole at the same time,
or the case may be damaged.
*3
16 dia.
16.3
9.2
+0.075
-0.025
4.2
+0.1
-0.05
4.36
dia.
0.2
17.45
11.9
0.1
25.4
*1. Stainless-steel roller
*2. Two hexagonal nuts (3 t × 17 width across flats)
49.2
*3. Incomplete screw part with a maximum length of 1.5 mm.
Z-15GQ22-B
Z-15HQ22-B
Z-15EQ22-B
Z-10FQ22Y-B
OF
2.45 to 3.43 N
1.12 N
0.4 mm
3.58 mm
0.05 mm
1.96 to 2.79 N
1.12 N
0.3 mm
3.58 mm
0.025 mm
6.13 to 7.85 N
1.12 N
0.8 mm
3.58 mm
0.13 mm
4.46 to 7.26 N
1.12 N
1 mm
3.55 mm
0.1 mm
RF min.
PT max.
OT min.
MD max.
OP
33.4 1.2 mm
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
10
Z
Panel Mount Cross Roller Plunger
Z-15GQ21-B Z-15EQ21-B
0.25
23.3
12.7 dia. × 4.8 *1
PT
Z-15HQ21-B
Z-15GQ21-B
Z-15HQ21-B
OF
2.45 to 3.43 N
1.12 N
0.4 mm
3.58 mm
0.05 mm
1.96 to 2.79 N
1.12 N
0.3 mm
3.58 mm
0.025 mm
RF min.
PT max.
OT min.
MD max.
*2
OP
15.5
16.3
M12 × 1
mounting
screw
+0.075
-0.025
4.2
dia. hole
*3
16 dia.
OP
33.4 1.2 mm
9.2
+0.075
-0.025
Z-15EQ21-B
4.2
+0.1
OF
6.13 to 7.85 N
1.12 N
0.8 mm
3.58 mm
0.13 mm
4.36
dia.
-0.05
0.2
17.45
RF min.
PT max.
OT min.
MD max.
11.9
0.1
25.4
*1. Stainless-steel roller
*2. Two hexagonal nuts (3 t × 17 width
49.2
across flats)
Note: Do not use the M12 mounting screw and the
case mounting hole at the same time, or the
case may be damaged.
*3. Incomplete screw part with a maximum
length of 1.5 mm.
OP
33.4 1.2 mm
Leaf Spring
Z-15GL-B
t = 0.3*
4.8
0.8
49.6
+0.075
-0.025
4.2
dia. hole
OF max.
RF min.
OT *min.
MD max.
1.38 N
0.14 N
1.6 mm
1.3 mm
FP
OP
23.9
9.2
FP max.
OP
20.6 mm
17.4 0.8 mm
+0.075
-0.025
4.2
+0.1
4.36
dia.
-0.05
0.2
11.9
17.45
* When operating, be sure not
to exceed 1.6 mm.
0.1
25.4
* Stainless-steel spring lever
49.2
9.5 dia. × 4
(plastic toller)
Roller Leaf Spring
Z-15GL2-B
0.8
46
t = 0.3 *
4.2+0.075
-0.025 dia. hole
OF max.
RF min.
OT *min.
MD max.
1.38 N
0.14 N
1.6 mm
1.3 mm
FP
OP
23.9
9.2
+0.075
-0.025
FP max.
OP
31.8 mm
28.6 0.8 mm
4.2
+0.1
4.36
dia.
-0.05
0.2
17.45
11.9
* When operating, be sure not
to exceed 1.6 mm.
0.1
25.4
* Stainless-steel spring lever
49.2
t = 1 *
Short Hinge Lever
Z-15GW21-B
26.2
4.9
FP
20.2
OP
16.9
13.9
OF max.
RF min.
OT min.
MD max.
1.57 N
0.27 N
2 mm
1 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
4.2
dia. hole
+0.1
4.36
dia.
-0.05
FP max.
OP
24.8 mm
19 0.8 mm
0.2
17.45
* Stainless-steel lever
11.9
0.1
25.4
49.2
t = 1 *
Hinge Lever
Z-15GW-B Z-15GW32-B
4.9
26.2
Z-15HW-B
Z-15GW3-B (Lever Length: 56R)*
Z-10FWY-B
FP
20.2
OP
16.9
4.2
13.9
9.2
+0.075
-0.025
+0.075
-0.025
4.2
dia. hole
+0.1
-0.05
4.36
dia.
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Z-15GW-B
Z-15HW-B
Z-15GW32-B
Z-10FWY-B
Z-15GW3-B
* The external dimensions of the actuator vary.
OF
0.69 N max.
0.14 N
5.6 mm
0.66 N max.
0.14 N
5.6 mm
1.47 to 1.96 N
0.92 N
5.6 mm
1.27 mm
0.88 N max.
0.14 N
5.6 mm
0.78 N max.
0.15 N
4.8 mm
RF min.
OT min.
MD max.
1.27 mm
0.63 mm
2.4 mm
1.12 mm
FP max.
OP
28.2 mm
27.4 mm
28.2 mm
29.8 mm
27.2 mm
19 0.8 mm
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
11
Z
Low-force Hinge Lever
Z-15GW4-B
t = 1 *
PT
4.9
26.2
20.2
OP
16.9
13.9
OF max.
RF min.
PT max.
OT min.
MD max.
274 mN
34.3 mN
10 mm
5.6 mm
1.27 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
4.2
dia. hole
+0.1
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
OP
19 0.8mm
* Stainless-steel lever
49.2
t = 0.8 *
Z-15HW24-B
5
2
120R
26.2
PT
20.2
OP
16.9
OF max.
RF min.
PT max.
OT min.
MD max.
58.8 mN
4.90 mN
19.8 mm
10 mm
13.9
9.2
+0.075
-0.025
4.2
+0.075
-0.025
4.2
dia. hole
+0.1
2 mm
4.36
dia.
-0.05
0.2
17.45
11.9
OP
19.8 1.6 mm
0.1
25.4
49.2
* Stainless-steel lever
Low-force Wire Hinge Lever
Z-15HW52-B
Z-15HW78-B (Lever Length: 110R) *
Z-15HW52-B
t = 1 *
OF max.
RF min.
PT max.
OT min.
MD max.
58.8 mN
4.90 mN
8.3 mm
5.6 mm
0.65 mm
3 max.
20.2
26.2
PT
OP
16.9
13.9
OP
19 1 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
4.2
dia. hole
+0.1
-0.05
4.36
dia.
* The external dimensions of the actuator vary.
Note: AC electrical ratings: 10 A, 125/250 V.
Z-15HW78-B
0.2
17.45
11.9
0.1
25.4
OF max.
RF min.
PT max.
OT min.
MD max.
39.2 mN
2.94 mN
10 mm
6 mm
* Stainless-steel wire lever
49.2
3 mm
OP
20 1 mm
Short Hinge Roller Lever
Z-15GW22-B Z-01HW22-B
Z-15HW22-B Z-10FW22Y-B
Z-15EW22-B
9.5 dia. × 4
(plastic roller)
t = 1 *
26.2
Z-15GW2-B * Z-15HW2-B *
Z-10FW2Y-B *
FP
OP
20.2
16.9
13.9
4.2
9.2
+0.075
-0.025
4.2
+0.075
-0.025
dia. hole
+0.1
-0.05
4.36
dia.
* The external
dimensions of the
actuator vary.
(Lever Length:
48.5R)
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Z-15GW22-B
Z-15HW22-B
Z-15EW22-B
Z-01HW22-B
Z-10FW22Y-B
Z-15GW2-B
Z-15HW2-B
Z-10FW2Y-B
OF max.
RF min.
OT min.
MD max.
1.57 N
0.41 N
2.4 mm
0.5 mm
1.47 N
0.41 N
2.4 mm
0.45 mm
1.94 N
0.41 N
2.4 mm
1.3 mm
1.57 N
0.27 N
2.4 mm
0.5 mm
2.45 N
0.34 N
2.4 mm
1 mm
0.98 N
0.22 N
4 mm
0.84 N
0.22 N
4 mm
1.27 N
0.22 N
4 mm
2 mm
1.02 mm
0.6 mm
FP max.
OP
32.5 mm
30.2 0.4 mm
35.1 mm
30.2 0.4 mm
32.5 mm
30.2 0.4 mm
34.8 mm
30.2 0.4 mm
36.5 mm
30.2 0.8 mm
37.4 mm
30.2 0.8 mm
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
12
Z
Short Hinge Cross Roller Lever
Z-15GW49-B
26.2
9.5 dia. × 4
(plastic roller)
t = 1 *
Z-15GW54-B (Lever Length: 48.7R) *
FP
OP
Z-15GW49-B
Z-15GW54-B
20.2
16.9
13.9
4.2
OF max.
RF min.
OT min.
MD max.
1.67 N
0.41 N
2.4 mm
0.98 N
0.22 N
4 mm
1 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
dia. hole
0.51 mm
+0.1
4.36
dia.
-0.05
FP max.
OP
33.3 mm
31 0.4 mm
37.3 mm
31 0.8 mm
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
* The external dimensions of the actuator vary.
20 dia. × 4
R2 (plastic roller)
Hinge Roller Lever
Z-15GW25-B
26.2
t = 1*
FP
OP
20.2
OF max.
RF min.
OT min.
MD max.
0.98 N
0.21 N
4 mm
16.9
13.9
4.2
9.2
+0.075
-0.025
1.6 mm
4.2
+0.075
-0.025
dia. hole
+0.1
FP max.
OP
47.5 mm
41.2 0.8 mm
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Operating direction
26.2
Unidirectional Short Hinge Roller Lever
Z-15GW2277-B
9.5 dia. × 4
(plastic roller)
t = 1 *
FP
OP
34.1 max.
20.2
16.9
OF max.
RF min.
OT min.
MD max.
1.67 N
0.41 N
2.4 mm
0.51 mm
13.9
4.2
9.2
+0.075
-0.025
4.2
+0.075
-0.025
dia. hole
+0.1
FP max.
OP
43.6 mm
41.3 0.8 mm
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
t = 1 *
Reverse Hinge Lever **
Z-15GM-B
4.9
18.65
FP
20.2
17.4
OP
OF max.
RF min.
OT min.
MD max.
1.67 N
0.27 N
5.6 mm
0.89 mm
13.9
9.2
+0.075
-0.025
4.2
4.2 +0.075
-0.025 dia. hole
+0.1
4.36
dia.
-0.05
FP max.
OP
23.8 mm
19 0.8 mm
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
t = 1 *
9.5 dia. × 4
(plastic roller)
Reverse Short Hinge Roller Lever **
Z-15GM22-B
18.65
Z-10FM22Y-B
Z-15GM22-B
Z-10FM22Y-B
FP
OP
20.2
17.4
OF max.
RF min.
OT min.
MD max.
5.28 N
1.67 N
2 mm
6.37 N
1.67 N
2 mm
13.9
9.2
+0.075
-0.025
4.2
0.28 mm
0.56mm
4.2 +0.075
-0.025 dia. hole
+0.1
4.36
dia.
FP max.
OP
31.8 mm
29.4 0.4 mm
33 mm
29.4 0.4 mm
-0.05
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
t = 1*
9.5 dia. × 4
(plastic roller)
Reverse Hinge Roller Lever **
Z-15GM2-B
18.65
FP
OP
20.2
OF max.
RF min.
OT min.
MD max.
2.35 N
0.55 N
4 mm
17.4
13.9
9.2
+0.075
-0.025
0.64 mm
4.2
4.2 +0.075
-0.025 dia. hole
+0.1
FP max.
OP
35 mm
30.2 0.8 mm
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
** The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers are freed by operating
the levers. Reverse-type models are highly vibration- and shock-resistive because the pin plungers are normally pressed.
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
13
Z
(Drip-proof) without Terminal Protective Cover
Basic Models
Terminals (Molded Terminals: Refer to page 21.)
Without Terminal Protective Cover
9.2
20
20
0.2
17.45
COM
1
NO
NC
2
Three, M4 × 5.5
Terminal screws
(with toothed
washer)
Note: With reverse action models (Z-15GM), the positions of NO and NC terminals are
reversed.
3
49.2
Dimensions and Operating Characteristics
The above illustration is for model without terminal protective cover.
Pin Plunger
Z-15G55-B
3.9 dia.
PT
4.2 +0.075
-0.025 dia. hole
0.25
23.3
6SR *
Z-01H55-B
OP
Z-15G55-B
Z-01H55-B
23.9
9.2
OF
2.45 to 4.22 N
1.12 N
2.2 mm
0.13 mm
0.06 mm
3.43 N max.
0.78 N
2.2 mm
0.13 mm
0.06 mm
+0.075
-0.025
4.2
RF min.
PT max.
OT min.
MD max.
+0.1
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
* Stainless-steel plunger
49.2
OP
15.9 0.4 mm
Short Spring Plunger
Z-15GD55-B
Z-01HD55-B
15 dia.
PT
0.25
11.9SR *
23.3
7.15 dia.
4.2+0.075
-0.025 dia. hole
OP
Z-15GD55-B
Z-01HD55-B
23.9
9.2
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
1.8 mm
1.6 mm
0.06 mm
3.63 N
0.78 N
1.9 mm
1.6 mm
0.06 mm
+0.075
-0.025
4.2
+0.1
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
* Stainless-steel plunger
49.2
OP
21.5 0.5 mm
Spring Plunger
Z-15GK55-B
17 dia.
PT
0.25
11.9SR *
23.3
7.15 dia.
4.2 +0.075
-0.025 dia. hole
OP
23.9
9.2
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
2.3 mm
1.6 mm
0.06 mm
+0.075
-0.025
4.2
+0.1
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
* Stainless-steel plunger
49.2
OP
28.2 0.5 mm
Z-15GK355-B
17 dia.
PT
0.25
11.9SR *
23.3
8.35 dia.
4.2 +0.075
-0.025 dia. hole
OP
23.5
9.2
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
2.4 mm
3.5 mm
0.06 mm
+0.075
-0.025
4.2
+0.1
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
* Stainless-steel plunger
49.2
OP
37.8 1.2 mm
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
14
Z
Panel Mount Plunger
Z-15GQ55-B
8.35 dia.
M12 × 1
0.25
23.3
PT
11.9SR
*1
Mounting
screw
*2
OP
13.1
16.3
4.2 +0.075
-0.025 dia. hole
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
1.8 mm
5.5 mm
0.06 mm
*3
*4
16 dia.
9.2
+0.075
-0.025
4.2
OP
21.8 0.8 mm
+0.1
4.36
dia.
-0.05
0.2
17.45
Note: Do not use the M12
mounting screw and the
case mounting hole at
the same time, or the
case may be damaged.
11.9
0.1
25.4
49.2
*1. Stainless-steel plunger
*2. Two hexagonal nuts (2 t × 14 width across flats)
*3. Two lock nuts (2 t × 15.6 width across flats)
*4. Incomplete screw part with a maximum length of 1.5 mm.
Panel Mount Roller Plunger
Z-15GQ2255-B
0.25
23.3
12.7 dia. × 4.8 *1
PT
*2
OP
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
1.8 mm
3.58 mm
0.06 mm
15.5
16.3
M12 × 1
mounting screw
4.2+0.075
-0.025 dia. hole
*3
16 dia.
9.2
+0.075
-0.025
OP
33.4 1.2 mm
4.2
+0.1
4.36
dia.
Note: Do not use the M12
mounting screw and the
case mounting hole at
the same time, or the
case may be damaged.
-0.05
0.2
17.45
11.9
0.1
25.4
49.2
*1. Stainless-steel roller
*2. Two hexagonal nuts (3 t × 17 width across flats)
*3. Incomplete screw part with a maximum length of 1.5 mm.
Panel Mount Cross Roller Plunger
Z-15GQ2155-B
0.25
23.3
12.7 dia. × 4.8 *1
PT
*2
OP
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
1.8 mm
3.58 mm
0.06 mm
15.5
16.3
M12 × 1
mounting
screw
4.2 +0.075
-0.025 dia. hole
*3
16 dia.
9.2
+0.075
-0.025
OP
33.4 1.2 mm
4.2
+0.1
4.36
dia.
Note: Do not use the M12
mounting screw and the
case mounting hole at
the same time, or the
case may be damaged.
-0.05
0.2
17.45
11.9
0.1
25.4
49.2
*1. Stainless-steel roller
*2. Two hexagonal nuts (3 t × 17 width across flats)
*3. Incomplete screw part with a maximum length of 1.5 mm.
Leaf Spring
Z-15GL55-B
t = 0.3 *
4.8
0.8
49.6
+0.075
-0.025
4.2
dia. hole
OF max.
RF min.
OT *min.
MD max.
1.96 N
0.14 N
1.6 mm
1.3 mm
FP
OP
23.9
9.2
FP max.
OP
20.6 mm
17.5 0.8 mm
+0.075
-0.025
4.2
+0.1
-0.05
4.36
dia.
0.2
* When operating, be sure not to
exceed 1.6 mm.
17.45
* Stainless-steel spring lever
11.9
0.1
25.4
49.2
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
15
Z
Roller Leaf Spring
Z-15GL255-B
9.5 dia. × 4
(plastic roller)
0.8
46
t = 0.3*
4.2+0.075
-0.025 dia. hole
OF max.
RF min.
OT *min.
MD max.
1.96 N
0.14 N
1.6 mm
1.3 mm
FP
OP
23.9
9.2
FP max.
OP
31.8 mm
28.6 0.8 mm
+0.075
-0.025
4.2
+0.1
-0.05
4.36
dia.
0.2
17.45
* When operating, be sure not to
exceed 1.6 mm.
11.9
0.1
25.4
* Stainless-steel lever
49.2
Short Hinge Lever
Z-15GW2155-B
t = 1*
26.2
4.9
FP
20.2
OP
16.9
13.9
OF max.
RF min.
OT min.
MD max.
1.86 N
0.27 N
2 mm
1 mm
9.2
+0.075
-0.025
4.2
4.2 +0.075
-0.025 dia. hole
+0.1
4.36
dia.
-0.05
FP max.
OP
25 mm
19 0.8 mm
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Long Hinge Lever
Z-15GW4455-B
t = 1 *
4.9
26.2
FP
20.2
OP
16.9
13.9
4.2
OF max.
RF min.
OT min.
MD max.
0.88 N
0.14 N
5.6 mm
3.5 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
dia. hole
+0.1
-0.05
4.36
dia.
0.2
FP max.
OP
33 mm
19 1.2 mm
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Hinge Lever
Z-15GW55-B
t = 1*
4.9
26.2
FP
20.2
OP
16.9
13.9
4.2
OF max.
RF min.
OT min.
MD max.
0.98 N
0.14 N
5.6 mm
2 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
dia. hole
+0.1
-0.05
4.36
dia.
FP max.
OP
28.2 mm
19 0.8 mm
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Short Hinge Roller Lever
Z-15GW2255-B
9.5 dia. × 4
(plastic roller)
t = 1 *
26.2
Z-01HW2255-B
FP
OP
Z-15GW2255-B Z-01HW2255-B
20.2
16.9
13.9
OF max.
RF min.
OT min.
MD max.
1.96 N
0.41 N
2.4 mm
0.8 mm
1.96 N
0.27 N
2.4 mm
0.8 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
4.2
dia. hole
+0.1
-0.05
4.36
dia.
0.2
FP max.
OP
32.9 mm
30.2 0.4 mm
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
16
Z
Hinge Roller Lever
Z-15GW255-B
9.5 dia. × 4
(plastic roller)
26.2
t = 1 *
FP
OP
20.2
16.9
13.9
OF max.
RF min.
OT min.
MD max.
1.27 N
0.21 N
4 mm
9.2
+0.075
-0.025
4.2
4.2 +0.075
-0.025 dia. hole
+0.1
1.6 mm
4.36
dia.
-0.05
0.2
17.45
11.9
FP max.
OP
36.5 mm
30.2 0.8 mm
0.1
25.4
* Stainless-steel lever
49.2
Unidirectional Short Hinge Roller Lever
Z-15GW227755-B
Operating direction
26.2
9.5 dia. × 4
(plastic roller)
t = 1 *
FP
OP
34.1 max.
20.2
16.9
13.9
4.2
OF max.
RF min.
OT min.
MD max.
1.77 N
0.49 N
2.4 mm
0.8 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
dia. hole
+0.1
-0.05
4.36
dia.
0.2
FP max.
OP
43.6 mm
41.3 0.8 mm
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Reverse Hinge Lever *
Z-15GM55-B
t = 1 *
4.9
18.65
FP
20.2
OP
17.4
13.9
OF max.
RF min.
OT min.
MD max.
1.96 N
0.27 N
5.6 mm
0.89 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
4.2
dia. hole
+0.1
4.36
dia.
-0.05
FP max.
OP
23.8 mm
19 0.8 mm
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Reverse Short Hinge Roller Lever *
Z-15GM2255-B
t = 1 *
9.5 dia. × 4
(plastic roller)
18.65
FP
OP
20.2
17.4
13.9
4.2
OF max.
RF min.
OT min.
MD max.
5.69 N
1.67 N
2 mm
9.2
+0.075
-0.025
4.2
+0.075
-0.025
dia. hole
0.28 mm
+0.1
4.36
dia.
-0.05
FP max.
OP
31.8mm
29.4 0.4mm
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
Reverse Hinge Roller Lever *
Z-15GM255-B
9.5 dia. × 4
(plastic roller)
t = 1 *
18.65
FP
OP
20.2
17.4
13.9
OF max.
RF min.
OT min.
MD max.
2.65 N
0.55 N
4 mm
9.2
+0.075
-0.025
4.2
+0.075
0.64 mm
4.2
dia. hole
-0.025
+0.1
4.36
dia.
-0.05
FP max.
OP
35 mm
30.2 0.8 mm
0.2
17.45
11.9
0.1
25.4
* Stainless-steel lever
49.2
* The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers are freed by operating
the levers.
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
17
Z
Flexible Rod (Coil Spring)
Z-15GNJ55-B
*1
6.1 dia.
3.2 dia.
PT
Nylon rod
30 Operating range *2
38
(111.3)
43.4
12 dia.
Rubber cap
0.25
23.3
OF max.
PT max.
0.49 N
(20 mm)
+0.075
-0.025
(13.6)
16.3
4.2
dia. hole
TT max.
40 mm
9.2
*1. Operation is possible in any direction other than the
axial direction (indicated by the arrow ).
*2. Use only the area within the top 30 mm of the rod as
the operating part. (Do not use the area that falls within
80 mm from the mounting hole as the operating part.
Using this area may cause damage to the nylon rod.
+0.075
-0.025
4.2
+0.1
4.36
dia.
-0.05
0.2
17.45
11.9
0.1
25.4
49.2
Flexible Rod (Steel Wire)
Z-15HNJS55-B
*1
PT
1-dia. stainless
steel wire *3
30 Operating range *2
0.4
100
Four, M3 set screws
with hexagonal holes
(130.1)
(22)
12 dia.
Rubber cap
0.25
23.3
4.2 +0.075
-0.025 dia. hole
(13.8)
16.3
OF max.
PT max.
0.15 N
(25 mm)
9.2
+0.075
-0.025
4.2
*1. Operation is possible in any direction other than the axial
direction (indicated by the arrow ).
+0.1
4.36
dia.
-0.05
0.2
17.45
11.9
*2. Use only the area within the top 30 mm of the rod as the
operating part. (Do not use the area that falls within 100
mm from the mounting hole as the operating part.
Using this area may cause damage to the steel wire.)
*3. The steel wire can be replaced if damaged.
(Model: Lever for HNJS55)
0.1
25.4
49.2
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
18
Z
(Drip-proof) with Terminal Protective Cover
Basic Models
Dimensions and Operating Characteristics
Pin Plunger
Z-15GA55-B5V
6SR *
PT
3.9 dia.
0.25
23.3
OP
14.7
(11)
OF max. 2.45 to 4.22 N
+0.075
-0.025
RF min.
PT max.
OT min.
MD max.
1.12 N
2.2 mm
0.13 mm
0.06 mm
4.2
19.2
+0.1
4.36
dia.
-0.05
+0.075
-0.025
4.2
dia. hole
0.2
17.45
0.1
25.4
13.7
OP
15.9 0.4 mm
52.8
* Stainless-steel plunger
(28.8)
17 dia.
Z-15GK3A55-B5V
PT
0.25
23.3
11.9SR *
8.35 dia.
OP
14.7
(11)
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
2.4 mm
3.5 mm
0.06 mm
+0.075
-0.025
4.2
19.2
+0.1
-0.05
4.36
dia.
4.2 +0.075
-0.025 dia. hole
OP
37.8 1.2 mm
0.2
17.45
0.1
25.4
13.7
52.8
* Stainless-steel plunger
(28.8)
8.35 dia.
Panel Mount Plunger
Z-15GQA55-B5V
PT
OP
0.25
23.3
11.9SR *1
M12 P = 1
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
1.8 mm
5.5 mm
0.06 mm
*2
*3
13.1
16 dia.
16.3
OP
21.8 0.8 mm
(11)
+0.075
-0.025
4.2
19.2
Note: Do not use the M12
mounting screw and the
case mounting hole at
the same time, or the
case may be damaged.
+0.1
4.36
dia.
-0.05
4.2 +0.075
-0.025dia. hole
0.2
17.45
0.1
25.4
13.7
*1. Stainless-steel plunger
52.8
(28.8)
*2. Two hexagonal nuts (2 t × 14 width across flat)
*3. Two lock nuts (2 t × 15.6 width across flats)
PT
0.25
23.3
Panel Mount Roller Plunger
Z-15GQ22A55-B5V
12.7 dia. × 4.8 *1
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
1.8 mm
3.58 mm
0.06 mm
*2
OP
M12 P = 1
15.5
16 dia.
16.3
19.2
OP
33.4 1.2 mm
Note: Do not use the M12
mounting screw and the
case mounting hole at
the same time, or the
case may be damaged.
(11)
+0.075
-0.025
4.2
+0.1
4.36
dia.
-0.05
4.2 +0.075
-0.025 dia. hole
0.2
17.45
0.1
25.4
13.7
*1. Stainless-steel roller
*2. Two hexagonal nuts (3 t × 17 width across flats)
52.8
(28.8)
PT
OP
0.25
23.3
Panel Mount Cross-roller Plunger
Z-15GQ21A55-B5V
12.7 dia. × 4.8 *1
OF max.
RF min.
PT max.
OT min.
MD max.
5.30 N
1.12 N
1.8 mm
3.58mm
0.06 mm
*2
M12 P = 1
15.5
16 dia.
16.3
OP
33.4 1.2 mm
Note: Do not use the M12
mounting screw and the
case mounting hole at
the same time, or the
case may be damaged.
(11)
+0.075
-0.025
4.2
19.2
+0.1
4.36
dia.
-0.05
4.2 +0.075
-0.025 dia. hole
0.2
17.45
0.1
25.4
13.7
*1. Stainless-steel roller
52.8
(28.8)
*2. Two hexagonal nuts (3 t × 17 width across flats)
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
19
Z
Long Hinge Lever
Z-15GW44A55-B5V
t = 1 *
4.9
26.2
FP
20.2
OP
OP
OP
16.9
13.9
OF max.
RF min.
OT min.
MD max.
0.88 N
0.14 N
5.6 mm
3.5 mm
(11)
+0.075
-0.025
4.2
19.2
+0.1
4.36
dia.
-0.05
4.2 +0.075
-0.025 dia. hole
FP max.
OP
33 mm
19 1.2 mm
0.2
17.45
0.1
25.4
13.7
52.8
* Stainless-steel lever
(28.8)
Hinge Lever
t = 1 *
Z-15GWA55-B5V
4.9
26.2
FP
20.2
OF max.
RF min.
OT min.
MD max.
0.98 N
0.14 N
5.6 mm
2 mm
16.9
13.9
(11)
+0.075
-0.025
4.2
19.2
FP max.
OP
28.2 mm
19 0.8 mm
+0.1
-0.05
4.36
dia.
4.2 +0.075
-0.025 dia. hole
0.2
17.45
0.1
25.4
13.7
52.8
* Stainless-steel lever
(28.8)
Short Hinge Roller Lever
Z-15GW22A55-B5V
t = 1 *
9.5 dia. × 4
(plastic roller)
26.2
FP
OF max.
RF min.
OT min.
MD max.
1.96 N
0.41 N
2.4 mm
0.8 mm
20.2
16.9
13.9
(11)
+0.075
-0.025
4.2
19.2
FP max.
OP
32.9 mm
30.2 0.4 mm
+0.1
4.36
dia.
-0.05
4.2 +0.075
-0.025 dia. hole
0.2
17.45
0.1
25.4
13.7
52.8
* Stainless-steel lever
(28.8)
Hinge Roller Lever
Z-15GW2A55-B5V
9.5 dia. × 4
(plastic roller)
26.2
t = 1 *
FP
OP
OF max.
RF min.
OT min.
MD max.
1.27 N
0.21 N
4 mm
20.2
16.9
13.9
(11)
+0.075
-0.025
1.6 mm
4.2
19.2
FP max.
OP
36.5 mm
30.2 0.8 mm
+0.1
4.36
dia.
-0.05
4.2 +0.075
-0.025dia. hole
0.2
17.45
0.1
25.4
13.7
52.8
* Stainless-steel lever
(28.8)
Unidirectional Short Hinge Roller Lever
Z-15GW2277A55-B5V
Operating direction
26.2
9.5 dia. × 4
(plastic roller)
t = 1 *
FP
OP
34.1 max.
OF max.
RF min.
OT min.
MD max.
1.77 N
0.49 N
2.4 mm
0.8 mm
20.2
16.9
13.9
(11)
+0.075
-0.025
4.2
19.2
FP max.
OP
43.6 mm
41.3 0.8 mm
+0.1
4.36
dia.
-0.05
+0.075
4.2
dia. hole
-0.025
0.2
17.45
0.1
25.4
13.7
52.8
* Stainless-steel lever
(28.8)
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
20
Z
(Drop-proof) with Modeled terminals
Basic Models
Molded Terminals
L/R Type (The following illustration is the R type.)
D Type
c
a
a
c
38
5
b
b
Size (mm)
Lead wire
Size (mm)
a
b
c
a
b
c
Lead wire
VSF
VCT
VSF
VCT
12
4
12
12
4
13
19 11 16
19 11 20
Lead Wire Specifications
Specifications Nominal cross sec-
tional area (mm2)
Finished outer
diameter (mm)
Connection
to terminal
Length (m)
Lead wire
VSF (single-core, vinyl cord)
Approx. 3.1 dia.
Black:COM
White:NO
Red: NC
1.25
1, 3
Three-core:
approx. 10.5 dia.
VCT (vinyl-insulated cable)
Note: 1. No models with molded terminals are approved by UL, CSA, or EN.
2. Molded terminals are not available on all models. Contact your OMRON representative for applicable products.
Maintained-contact Models
Dimensions and Operating Characteristics
Pin Plunger
Z-15ER
2.3 dia.
+0.075
-0.025
PT
0.25
23.3
4.2
dia. hole
2.3SR *1
Plunger
OF max. 1.96 to 2.50 N
Reset position
OP
7.1 min.
6.4 dia.
21.4
6.4
PT max.
OT min.
0.4 mm
0.13 mm
+0.075
-0.025
+0.1
-0.05
4.2
4.36
dia.
Reset free
position
0.3
14.3
25.4
OP
15.9 0.4 mm
11.9
Reset button *2
0.1
0.2
9.5 max.
17.45
49.2
Reset Button
NO
NC
COM
OF max. 0.55 to 2.79 N
*1. Stainless steel plunger
*2. Plastic plunger
OT min.
0.4 mm
Slim Spring Plunger
Z-15ESR
5.2 dia.
4 dia.
0.25
23.3
*1
PT
Plunger
+0.075
-0.025
4.2
dia. hole
OF max.
PT max.
OT min.
2.65 N
0.4 mm
1.6 mm
OP
Reset position
7.1 min.
9 dia.
21.4
6.4
OP
28.2 0.5 mm
+0.075
4.2
-0.025
+0.1
6.4 dia.
4.36
dia.
-0.05
Reset free
0.3
14.3
position 9.5 max.
11.9
Reset button *2
Reset Button
0.1
25.4
0.2
17.45
49.2
*1. Stainless steel plunger (tip only, flat, R1 bevel).
*2. Plastic plunger
OF max.
OT min.
2.79 N
0.4 mm
Hinge Lever
Z-15EWR
t = 1 *1
4.9
26.2
Lever Tip
FP
OF max.
OT min.
0.54 N
5.6 mm
Reset position
7.1 min.
20.2
OP
16.9
13.9
FP max.
OP
28.2 mm
19 0.8 mm
6.4
+0.075
4.2
-0.025
+0.1
4.36
dia.
6.4 dia.
-0.05
Reset free
position
9.5 max.
0.3
14.3
25.4
4.2 +0.075
-0.025 dia. hole
Reset button *2
11.9
0.1
0.2
17.45
Reset Button
49.2
*1. Stainless steel lever
*2. Plastic plunger
OF max.
OT min.
2.94 N
0.4 mm
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
21
Z
Accessories (Order Separately)
A Terminal Protective Cover, Actuators, and a Separator are available.
Drip-proof Terminal
Cover (Order Separately)
The Drip-proof Terminal Protective Cover is provided for maintenance for Z-@A55-B5V Switches.
Ordering Information
Dimensions
(Unit: mm)
Name
Model
Drip-proof Terminal
Protective Cover
17.4
13.5 dia. 17 dia.
AP-DV
48.5-+21
11
Mounting bracket
7.5
27.9
15
17.4
0.6
51.6
9
17.4
29.5±1
Terminal Covers (Sold Separately)
Separator (Sold Separately)
The Terminal Covers can be attached to Z, A, X, and DZ Switches.
Use a Separator when it is difficult to
provide a sufficient insulation distance or
when using the Switch near metal parts or
copper wires.
The Terminal Cover is secured with mounting screws and protects the casing and terminal wires
from dust, vibration, or fingers, thus preventing terminal short-circuiting, ground faults, wire
disconnection or improper connection, and electric shock accidents.
Terminal Covers made of phenol resin have five or six thin wall sections. These sections can be
torn open for providing holes for lead cables at desired points.
A terminal cover can’t be used in the case of using an actuator sold separately.
Operation Information
Model
SEPARATOR FOR Z
Operation Information
Application Soldering terminal use Screw terminal use
Remarks
Material
Mounting direction
Side mounting
Model
AP-Z
Phenol resin
AP-A
AP-B
---
Metal press mold Side mounting
Vinyl chloride Side mounting
AP1-A
AP1-B
Used for AP-A and AP-B
---
Note: Use a Terminal Cover for screw terminals fir DZ-series Switches with soldering terminals.
22
Z
Dimensions (Unit: mm)
Terminal Covers
52.8
25.4
53.8
25.4
AP-A
Soldering Terminal Use
(Phenol Resin)
AP-B
Screw Terminal Use
(Phenol Resin)
4.3+0.2
4.3+0.2
4.3+0.2
4.3+0.2
0
0
0
0
8
8
8
8
16.3
6.5
20.2
6.5
2.15R
2.15R
21
21
Note: The Cover has five thin, easy-to-separate
portions for easy lead wire connections.
Note: The Cover has six thin, easy-to-separate
portions for easy lead wire connections.
55.4
25.4
54.4
25.4
AP1-A
Soldering Terminal Use
AP1-B
Screw Terminal Use
4.3+0.2
4.3+0.2
4.3+0.2
4.3+0.2
0
0
0
0
(Metal Press Mold)
(Metal Press Mold)
8
8
17.1
21
2.15R
2.15R
7.2
7
8.5 22.6
8.5 22.6
Note: The Cover has five holes for easy lead wire connections.
Note: The Cover has six holes for easy lead wire connections.
Two, 4.2 dia.
AP-Z
Pressure plate
(t1 steel)
52.8
25.4
Soldering or Screw Terminal Use
21
Cable Pull-out Dimension
(Vinyl Chloride)
7
14
A-A' cross-section
B-B' cross-section
21
6 dia.
15 8 dia.
13
39
46
Note: A 6-dia. or 8-dia. cable can be
used by cutting the cable pull-out
hole to the size of the cable to be
used.
A
B
A'
B'
13
15
M3 × 20 Phillips screw
(with plane washer and nut)
12
Nut
Note: Each dimension has a tolerance of 0.4 mm unless otherwise specified. ( 0.8 mm for the AP-Z)
Separator
Two, 4.5 dia.
13.5
27 0.5
Note: 1. Each dimension has a tolerance of 0.4 mm unless otherwise specified.
2. The material is EAVTC (Epoxide Alkyd Varnished Tetron Cloth) and its heat-resisting
temperature is 130°C.
11.9
25.4 0.2
49.2 0.5
t = 0.51
23
Z
Actuators (Sold Separately)
A Switch can be actuated by a cam or an appropriate object, in which case, use one of the following Actuators according to the application.
Ordering Information
Actuator
Application
Common to Z and X models
XAA-1
Hinge lever
Hinge roller lever
ZAA-2
Short
Medium
Long
ZAQ-3
ZAQ-2
ZAQ-1
Panel mount plunger
Panel mount roller plunger
ZAQ-22
Dimensions (Unit: mm) and Operating Characteristics
Note: These Actuators are not provided with Switches.
Two, M4 30
Two, M4
Hinge Lever
XAA-1
Model
Z-15G-B
X-10G-B
Operating characteristics
19.1
Operating force OF max.
4.90 N
1.67 N
12.7 mm
2.2 mm
4.90 N
1.67 N
12.7 mm
3.3 mm
Release force
Overtravel
RF min.
OT min.
X A A - 1
*
XAA-1
Movement Differential MD max.
7
Free Position
Operating Position OP
FP max.
32.9 1.6 mm
28.9 1.6 mm
FP
OP
29.4
Note: This Actuator can be used with the Z-15G(-B) and X-
10G(-B). When mounting the Switch, set the overtravel to
between 32% and 100%, taking into consideration the
operating body and the distance between the Actuator
and the dog.
20.5
38.5
* Stainless steel
11.9
25.4 0.1
49.2
Two, M4 30
Two, M4
Hinge Roller Lever
ZAA-2
Z-15G-B
X-10G-B
19.1
OF max.
RF min.
OT min.
MD max.
4.90 N
1.67 N
12.7 mm
4.90 N
1.67 N
12.7 mm
22.2
9.5 dia. × 4.8 *1
2.2 mm
3.3 mm
FP max.
OP
44.5 1.6 mm
40.4 1.6 mm
*2
7
Note: This Actuator can be used with the Z-15G(-
B) and ZX-10G(-B). When mounting the
Switch, set the overtravel to between 32%
and 100%, taking into consideration the
operating body and the distance between
the Actuator and the dog.
FP
OP
29.4
20.5
38.5
*1. Stainless steel roller
*2. Stainless steel
11.9
25.4 0.1
49.2
Short Panel Mount Plunger
7.9 dia.
23.3
12SR
ZAQ-3
M12 × 1 mounting
screw
2 t × 14 width
across flats
ZAQ-3
PT
Z-15E-B
X-10G-B
*1
OF max.
RF min.
PT max.
OT min.
MD max.
8.34 N
1.12 N
0.8 mm
4.8 mm
0.15 mm
5.39 N
1.12 N
1 mm
4.5 mm
0.2 mm
OP
17.5
*3
14.5
dia.
1.6
2 t × 15.6 width
across flats
Two, M4 nuts
20.7
OP
27.8 1.5 mm
24.2
22.6
Note: 1. This Actuator (pin plunger) can be used
with Standard Pin Plungers (Z-15G(-B),
Z-15E(-B), X-10G(-B), DZ-10G-1A(-1B))
for the Z, X, and DZ models.
*3
*2
13.5
Two, M4 × 25 screws
25.4 0.1
52.4
20.7
*1. Stainless-steel pin plunger
*2. Bronze frame
*3. Incomplete screw section part with a maximum of 1.5 mm
Note: Each dimension has a tolerance of 0.4 mm unless otherwise specified.
24
Z
Medium Panel Mount Plunger
ZAQ-2
7.9 dia.
PT
23.3
12SR
M12 × 1 mounting screw
*1
ZAQ-2
Z-15E-B
X-10G-B
2 t × 14 width across
flats
OF max.
RF min.
PT max.
OT min.
MD max.
8.34 N
1.12 N
0.8 mm
4.8 mm
0.15 mm
5.39 N
1.12 N
1 mm
4.5 mm
0.2 mm
OP
42.8
24.2
2 t × 15.6 width
across flats
14.5
dia.
*3
1.6
OP
53.2 1.5 mm
Note: This Actuator (pin plunger) can be used with
Standard Pin Plungers (Z-15G(-B), Z-15E(-
B), X-10G(-B), DZ-10G-1A(-1B)) for the Z,
X, and DZ models.
Two, M4 × 25 screws
20.7
22.6
*2
13.5
Two, M4 nuts
25.4 0.1
52.4
20.7
*1. Stainless-steel pin plunger
*2. Copper alloy frame
*3. Incomplete screw section part with a maximum of 1.5 mm
Long Panel Mount Plunger
ZAQ-1
7.9 dia.
PT
23.3
12SR
*1
ZAQ-1
Z-15E-B
X-10G-B
M12 × 1 mounting screw
OF max.
8.34 N
1.12 N
0.8 mm
20.6 mm
0.15 mm
5.39 N
1.12 N
1 mm
20.4 mm
0.2 mm
RF min.
PT max.
OT min.
MD max.
2 t × 14 width across
flats
OP
42.8
24.2
OP
69.1 1.5 mm
2 t × 15.6 width
across flats
Note: This Actuator (pin plunger) can be used with
Standard Pin Plungers (Z-15G(-B), Z-15E(-
B), X-10G(-B), DZ-10G-1A(-1B)) for the Z,
X, and DZ models.
14.5
dia.
*3
1.6
Two, M4 × 25 screws
20.7
22.6
*2
13.5
Two, M4 nuts
25.4 0.1
52.4
20.7
*1. Stainless-steel pin plunger
*2. Copper alloy frame
*3. Incomplete screw section part with a maximum of 1.5 mm
Panel Mount Roller Plunger
ZAQ-22
48
12.7 dia. *1
4.8
PT
23.3 0.25
Two hex nuts 5-mm
thickness, 19 mm
between opposing edges
With groove for roller
ZAQ-22
Z-15E-B
DZ-10G-1B
OF max.
8.34 N
1.12 N
2 mm
3.58 mm
0.15 mm
11.1 N
1.12 N
2 mm
1 mm
0.46 mm
penetration
OP
RF min.
PT max.
OT min.
MD max.
M12 × 1 mounting
screw
*3
18.9
23.9
1.6
14.5
dia.
OP
37 0.8 mm
35.4 1.2 mm
20.7
Note: This Actuator (roller plunger) can be used with
standard pin plungers (Z-15G(-B), Z-15E(-B),
and DZ-10G-1A(-1B)). It cannot be used with
X models.
Two, M4 × 25
screws
Spring washer
*2
25.4 0.2
49.2
20.7
11.9
*1. Stainless-steel pin plunger
*2. Steel frame
*3. Incomplete screw section part with a maximum of 1.5 mm
Note: Each dimension has a tolerance of 0.4 mm unless otherwise specified.
25
Z
Safety Precautions
Refer to Safety Precautions for All Basic Switches.
Precautions for Safe Use
Incorrect
Correct
Separate the
installation lo-
cation from
Terminal Connection
heat sources.
When soldering lead wires to the Switch, make sure that the capacity
of the soldering iron is 60 W maximum. Do not take more than 5 s to
solder any part of the Switch. The characteristics of the Switch will
deteriorate if a soldering iron with a capacity of more than 60 W is
applied to any part of the Switch for 5 s or more.
• Mount a cover if the switch is to be installed in a location where
worker inattention could result in incorrect operation or accidents.
Operation
Correct
Incorrect
• Make sure that the switching frequency or speed is within the
specified range.
1.If the switching speed is extremely slow, the contact may not be
switched smoothly, which may result in a contact failure or
contact welding.
(preventing malfunctions)
2.If the switching speed is extremely fast, switching shock may
damage the Switch soon. If the switching frequency is too high,
the contact may not catch up with the speed.
The rated permissible switching speed and frequency indicate the
switching reliability of the Switch.
The life of a Switch is determined at the specified switching speed.
The life varies with the switching speed and frequency even when
they are within the permissible ranges. In order to determine the
life of a Switch model to be applied to a particular use, it is best to
conduct an appropriate durability test on some samples of the
model under actual conditions.
• Subjecting the switch to continuous vibration or shock may result in
contact failure or faulty operation due to abrasion powder and in
reduced durability. Excessive vibration or shock will cause the
contacts to operate malfunction or become damaged. Mount the
switch in a location that is not subject to vibration or shock and in a
direction that does not subject the switch to resonance.
• If silver contacts are used with relatively low frequency for a long
time or are used with microloads, the sulfide coating produced on
the contact surface will not be broken down and contact faults will
result. Use a microload switch that uses gold contacts.
• Do not use the switch in atmospheres with high humidity or heat or
in harmful gases, such as sulfide gas (H2S, SO2), ammonia gas
(NH3), nitric acid gas (HNO3), or chlorine gas (Cl2). Doing so may
impair functionality, such as with damage due to contacting faults
or corrosion.
•
Make sure that the actuator travel does not exceed the permissible OT
position. The operating stroke must be set to 70% to 100% of the rated OT.
Precautions for Correct Use
• The switch includes contacts. If the switch is used in an atmosphere
with silicon gas, arc energy may cause silicon oxide (SiO2) to
accumulate on the contacts and result in contact failure. If there is
silicon oil, silicon filling, silicon wiring, or other silicon products in the
vicinity of the switch, use a contact protection circuit to limit arcing
and remove the source of the silicon gas.
Mounting Location
• Do not use the switch alone in atmospheres such as flammable or
explosive gases. Arcing and heat generation associated with
switching may cause fires or explosions.
•
Switches are generally not constructed with resistance against water. Use
a protective cover to prevent direct spraying if the switch is used in
locations subject to splashing or spurting oil or water, dust adhering.
Mounting
Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance.
Electric shock or burning may occur.
Incorrect
Correct
Selecting Models
We recommend using Drip-proof Models (protection equivalent to
IP62) in locations subject to floating dirt and dust. Other models do not
have a protective structure.
Terminal box
Terminal box
Wiring
• Install the switch in a location that is not directly subject to debris
and dust from cutting. The actuator and the switch body must be
protected from accumulated cutting debris and dirt.
• Use wire sizes that are suitable to the applied voltage and carried
current.
• If you use a soldering iron to solder the wires, do not allow the tip of
the soldering iron to exceed 380°C. If a Switch is used with
insufficient soldering, abnormal heat and burning may occur.
• Solder for no more than 5 s at 350°C and for no more than 3 s at
380°C. If heat is applied for too long, the case may melt, the lead
wire coverings may be scorched, and other characteristics of the
Switch may deteriorate.
Incorrect
Correct
• Do not use the switch in locations subject to hot water (greater than
60°C) or in water vapor.
Do not use the switch outside the specified temperature and
atmospheric conditions.
The permissible ambient temperature depends on the model. (Refer to
the specifications in this catalog.) Sudden thermal changes may cause
thermal shock to distort the switch and result in faults.
Tightening
•
The suitable tightening torque for screw terminals is given below.
Screw terminals except for those on Split-contact Models (Z-10FY-
B): 0.78 to 1.18 N·m
Screw terminals on Split-contact Models (Z-10FY-B):
0.49 to 1.18 N·m
Operation
• Make sure that the switching speed and frequency are is within the
specified ranges.
1. If the switching speed is extremely slow, the contacts may not be switched
smoothly, which may result in a contact failure or contact welding.
26
Z
2. If the switching speed is extremely fast, switching shock may
damage the Switch prematurely. If the switching frequency is too
high, the contacts may not be able to keep up with the speed.
The rated permissible switching speed and frequency indicate the
switching reliability of the Switch.
The life of a Switch is determined at the specified switching speed.
The life varies with the switching speed and frequency even when
they are within the permissible ranges. Always conduct appropriate
durability tests under actual conditions before using a Switch.
Models with Drip-proof Terminal Cover (Z-@A55-B5V)
Wiring
• To attach the Protective Cover to the case, hold the cover in almost
parallel to the case and then push it to the case. If the cover is
pushed diagonally, the rubber packing may slip off, degrading the
sealability of the Switch.
Terminal with
toothed
washer
•
Make sure that the actuator travel does not exceed the permissible OT
position. The operating stroke must be set to 70% to 100% of the rated OT.
Panel Mount Switch (Z-15@Q@, Z-01@Q@)
Rubber packing
• When mounting the panel mount plunger model with screws on a
side surface, be careful of the dog angle and operation speed.
Excessive dog angle or operation speed may damage the Switch.
• When using the panel mount plunger model mounted with screws
on a side surface, be careful not to apply a large shock. Applying a
shock exceeding 1,000 m/s2 may damage the Switch.
• Use round solderless terminals having the
following dimensions to connect leads to the
terminals. Tighten the screws of terminals to
a torque of 0.78 to 1.18 N·m. Use the
4.3 dia.
• When using the panel mount plunger model mounted with screws
on a side surface, remove the hexagonal nuts from the actuator.
8
High-sensitivity Switch (Z-15H)/
20 max.
terminal shown below.
• A cable 8.5 to 10.5 mm in diameter can be
Extra-high-sensitivity Switch (Z-15H2)
applicable to the sealing rubber of the lead outlet of the Switch. A
two-core or three-core VCT cable having a cross-sectional area of
1.25 mm2 is especially suitable for this.
• Use M4 small screws with spring toothed washer are used as the
terminal screws.
• When using the Switch in a DC circuit, be sure to provide an arc
suppressor as well because the small contact gap of the Switch
may result in contact troubles.
• In an application where a high repeat accuracy is required, limit the
current that flows through the Switch to within 0.1 A. Also, use a
relay to control a high-capacity load if the Switch is connected to
such a load. (In this case, the exciting current of the relay coil is the
load of the Switch.)
Drip-proof Switch (Z-@55)
• The Switch is not perfectly oil-tight; so do not dip it in oil or water.
• The rubber boots are made from weather-resistive chloroprene
rubber.
• Do not use Basic Switches in places with radical changes in
temperature.
• Rubber boots and rubber caps will tend to harden at lower ambient
temperatures. If an Actuator is used in a pressed state for an
extended period of time at low temperatures, it may return slowly or
it may not return at all. OMRON can provide special Actuators for
use at low temperature with rubber boots or rubber caps made of
silicon rubber, which has superior resistance to cold. Ask your
OMRON representative for details.
• Do not apply a force of 19.6 N or higher to the pin plunger.
• Exercise care that the environment conditions such as temperature
and humidity do not change abruptly.
Micro Load Applicable Range
Using a model for ordinary loads to open or close the contact of a
micro load circuit may result in faulty contact. Use models that operate
in the following range. However, even when using micro load models
within the operating range shown here, if inrush current occurs when
the contact is opened or closed, it may increase contact wear and so
decrease durability. Therefore, insert a contact protection circuit
where necessary.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability level
of 60% (λ 60). The equation, λ 60 = 0.5×10-6/operations indicates that
the estimated malfunction rate is less than 1/2,000,000 operations
with a reliability level of 60%.
Split-contact Switch (Z-10F@Y)
The applicable current varies depending on how the contacts are
used. If the Switch is connected in series, the Switch can endure a
current 1.5 to 2 times higher than the current that can be applied in
parallel connection.
5 mW
800 mW
Flexible Rod Switch (Z-15@NJ@55, Drip-proof)
• When the rod is fully swung, the Switch may operate when the lever
returns, causing chattering. Use a circuit that compensates for
chattering wherever possible.
• Do not switch the rod to the fullest extent when the Switch is to
break a power circuit because such a practice may cause metal
deposition to occur between the mating contacts of the Switch.
0.16 mA
26 mA
30
24
Operating
range for
general load
models
Z-15H, H2
Z-15G
Z-15E
Z-10FY
Z-15ER
Operating range
for micro load
models Z-01H
12
Other Precautions
Unusable
range
• Do not apply excessive force with a screwdriver or other tool when
attaching or removing the Protective Cover. Doing so may deform
the Switch.
5
0
1 mA
100 mA 160 mA
0.1
1
10
100
1,000
Current (mA)
Screwdriver
Z-01H
Z-15@, Z-10FY
Minimum applicable
load
1 mA at 5 VDC
160 mA at 5 VDC
• The Drip-proof Terminal Protective Cover can be sued only with
Switches with model numbers ending in “-B5V.”
• Only the Terminal Protective Cover is available for maintenance.
27
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2016.3
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2016 All Right Reserved.
Z-15GW2555-B 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
Z-15GW25A55-B | OMRON | Snap Acting/Limit Switch, | 获取价格 | |
Z-15GW25A55-B5V | OMRON | Snap Acting/Limit Switch, | 获取价格 | |
Z-15GW2A55 | OMRON | Snap Acting/Limit Switch, | 获取价格 | |
Z-15GW2A55-B | OMRON | Snap Acting/Limit Switch, | 获取价格 | |
Z-15GW2A55-B5V | OMRON | General-purpose Basic Switch | 获取价格 | |
Z-15GW2S55-B7-K | OMRON | General-purpose Basic Switch | 获取价格 | |
Z-15GW3 | OMRON | General-purpose Basic Switch | 获取价格 | |
Z-15GW3-B | OMRON | General-purpose Basic Switch | 获取价格 | |
Z-15GW32 | OMRON | General-purpose Basic Switch | 获取价格 | |
Z-15GW32-B | OMRON | General-purpose Basic Switch | 获取价格 |
Z-15GW2555-B 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6