CAT4016VSR [ONSEMI]
IC,LASER DIODE/LED DRIVER,SSOP,24PIN,PLASTIC;型号: | CAT4016VSR |
厂家: | ONSEMI |
描述: | IC,LASER DIODE/LED DRIVER,SSOP,24PIN,PLASTIC 驱动 光电二极管 接口集成电路 |
文件: | 总15页 (文件大小:226K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CAT4016
16-Channel Constant Current LED Driver
FEATURES
DESCRIPTION
16 Constant current-sink channels
Serial interface up to 25MHz clock frequency
3V to 5.5V logic supply
The CAT4016 is a 16 channel constant current driver
for LED billboard and other general display
applications. LED channel currents are programmed
together via an external RSET resistor. Low output
voltage operation on the LED channels as low as 0.4V
(for 2 to 100mA LED current) allows for more power
efficient designs.
LED current range from 2mA to 100mA
LED current set by external RSET resistor
300mV LED dropout at 30mA
Thermal shutdown protection
A high-speed 4-wire serial interface of up to 25MHz
clock frequency controls each individual channel using
a shift register and latch configuration. A serial output
data pin (SOUT) allows multiple devices to be
cascaded and programmed via one serial interface.
The device also includes a blanking control pin
(BLANK) that can be used to disable all channels
independently of the interface.
Available in RoHS-compliant 24-lead SOIC,
TSSOP, QSOP, and 4 x 4mm TQFN packages
APPLICATION
Billboard Display
Marquee Display
Instrument Display
General Purpose Display
Thermal shutdown protection is incorporated in the
device to disable the LED outputs if the die
temperature exceeds a set limit.
For Ordering Information details, see page 14.
The device is available in the 24-lead SOIC, TSSOP,
QSOP and the compact TQFN 4 x 4mm packages.
TYPICAL APPLICATION CIRCUIT
VIN
3V to
5.5V
20mA
1µF
VDD
LED1 LED2
LED16
BLANK
LATCH
SIN
to next
device
CAT4016
SOUT
RSET
CLK
3kΩ
GND
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. MD-5028 Rev. C
CAT4016
ORDERING INFORMATION
Part Number
Package
SOIC24(1)
Quantity per Reel
1,000
Package Marking
CAT4016W
CAT4016Y
4016VS
CAT4016W-T1
CAT4016Y-T2
TSSOP24(1)
QSOP24(1)
QSOP24(1)
TQFN24(1)
TQFN24(2)
2,000
CAT4016VS-T2
CAT4016VSR-T2
CAT4016HV6-T2
CAT4016HV6-GT2
2,000
2,000
4016VSR
LAAA
2,000
2,000
LAAD
Notes:
(1) Matte-Tin Plated Finish (RoHS-compliant)
(2) NiPdAu Plated Finish (RoHS-compliant)
PIN CONFIGURATION
24-Lead SOIC (W),
TSSOP (Y), QSOP (VS)
24-Lead QSOP (VSR)
1
2
3
4
5
6
24
23
22
21
20
19
VDD
1
2
3
4
5
6
24
23
22
21
20
19
GND
SIN
LED14
LED13
LED12
LED11
LED10
LED9
LED15
LED16
BLANK
SOUT
RSET
VDD
RSET
SOUT
BLANK
LED16
LED15
CLK
LATCH
LED1
LED2
7
18
17
16
15
14
13
LED3
LED4
LED5
LED6
LED7
LED8
LED14
LED13
LED12
LED11
LED10
LED9
7
18
17
16
15
14
13
GND
SIN
LED8
LED7
LED6
LED5
LED4
LED3
8
8
9
9
CLK
10
11
12
10
11
12
LATCH
LED1
LED2
24-Lead TQFN (HV6)
24 23 22 21 20 19
GND
SIN
1
2
3
4
5
6
18 LED14
17 LED13
16 LED12
15 LED11
14 LED10
13 LED9
CLK
LATCH
LED1
LED2
7
8
9
10 11 12
Doc. No. MD-5028 Rev. C
2
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT4016
ABSOLUTE MAXIMUM RATINGS
Parameter
Rating
Units
V
VDD Supply Voltage
6
-0.3V to VDD+0.3V
6
Logic input/output voltage (SIN, SOUT, CLK, BLANK, LATCH)
LEDn voltage
V
V
DC output current on LED1 to LED16
Storage Temperature Range
Junction Temperature Range
Lead Soldering Temperature (10sec.)
150
mA
°C
°C
°C
-55 to +160
-40 to +150
300
RECOMMENDED OPERATING CONDITIONS
Parameter
Range
3.0 to 5.5
0.4 to 5.5
up to 100
-40 to +85
Units
V
VDD
Voltage applied to LED1 to LED16
LED current RSET control range
Ambient Temperature Range
V
mA
°C
ELECTRICAL OPERATING CHARACTERISTICS
DC Characteristics
VDD = 5.0V, TAMB = 25 ºC, over recommended operating conditions unless specified otherwise.
Symbol Name
Conditions
Min
18
Typ
20
Max
22
Units
VLED = 1V, RSET = 3kꢀ
VLED = 1V, RSET = 1.5kꢀ
VLED = 1V, RSET = 750ꢀ
VLED = 1V, RSET = 3kꢀ
VLED = 1V, RSET = 1.5kꢀ
ILED-ACC
LED Current (any channel)
mA
36
40
44
80
±1.5
±1.5
±2.0
LED Current Matching
(ILED - ILEDAVR) / ILEDAVR
ILED-MAT
%
-6.0
+6.0
VLED = 1V, RSET = 750ꢀ
VDD within 4.5V and 5.5V
LED current 30mA
VLED within 1V and 3V
LED current 30mA
LED current regulation vs. VDD
LED current regulation vs. VLED
±0.1
% / V
% / V
ΔIVDD
±0.05
ΔIVLED
RSET = 3kꢀ
3
8.5
4
8
9
mA
mA
mA
IDDOFF
IDDON
Supply Current (all outputs off)
Supply Current (all outputs on)
R
SET = 750ꢀ
RSET = 3kꢀ
SET = 750ꢀ
R
10
mA
µA
kꢀ
kꢀ
ILKG
LEDn output Leakage
VLED = 5V, outputs off
-1
1
RLATCH
RBLANK
LATCH Pull-down Resistance
BLANK Pull-up Resistance
100
100
180
180
300
300
VIH
VIL
Logic high input voltage
Logic low input voltage
0.7xVDD
V
V
0.3xVDD
VHYS
Logic input hysteresis voltage
0.1xVDD
0
V
Logic Input leakage current
(CLK, SIN)
IIL
VI = VDD or GND
IOH = -1mA
-5
5
µA
V
VOH
VOL
SOUT logic high output voltage
SOUT logic low output voltage
VCC-0.3V
I
OL = 1mA
0.3
VRSET
TSD
RSET Regulated Voltage
Thermal Shutdown
1.17
1.20
160
20
1.23
V
ºC
ºC
THYST
Thermal Hysteresis
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
3
Doc. No. MD-5028 Rev. C
CAT4016
Timing Characteristics
For 3.0V ≤ VDD ≤ 5.5V, TAMB = 25 ºC, unless specified otherwise.
Symbol Name
CLK
Conditions
Min(1)
Typ(2)
Max(1)
Units
fclk
tcwh
tcwl
CLK Clock Frequency
25
MHz
ns
CLK Pulse Width High
CLK Pulse Width Low
20
20
ns
SIN
tssu
tsh
Setup time SIN to CLK
Hold time SIN to CLK
4
4
ns
ns
LATCH
tlwh
LATCH Pulse width
20
4
ns
ns
ns
Tlh
Hold time LATCH to CLK
Setup time LATCH to CLK
Tlsu
Channel Stagger Delay
LATCH to LED1 off/on
800
LEDn
tld
LED1 Propagation delay
40
17
300
40
ns
ns
tls
LED Propagation delay stagger LED(n) to LED(n+1)
LED Propagation delay stagger
LED1 to LED16
total
tlst
250
ns
tbd
tlr
BLANK Propagation delay
LED rise time (10% to 90%)
LED fall time (90% to 10%)
BLANK to LED(n) off/on
60
40
30
300
200
250
ns
ns
ns
Pull-up resistor = 50ꢀ to 3.0V
Pull-up resistor = 50ꢀ to 3.0V
tlf
SOUT
tor
SOUT rise time (10% to 90%)
SOUT fall time (90% to 10%)
Propagation delay time SOUT
CL = 15pF
5
5
ns
ns
ns
tof
CL = 15pF
tod
CLK to SOUT
8
15
25
Test Circuit for AC Characteristics
1µF
VDD
VDD
Rp
Rp
50ꢀ
50ꢀ
LED1
BLANK
LATCH
SIN
CAT4016
LED16
SOUT
V1
3V
CLK
Cl
15pF
RSET
GND
RSET
Notes:
(1) All min and max values are guaranteed by design.
(2) VDD = 5V, LED current 30mA.
Doc. No. MD-5028 Rev. C
4
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT4016
1/fclk
CLK
SIN
tssu
tsh
tcwl
tcwh
tod
SOUT
LATCH
tlh
tlsu
tlwh
Figure 1. Serial Input Timing Diagram
tld
LATCH
tbd
BLANK
LED1
tls
LED2
tlst = 15 tls
LED16
Figure 2. LED Output Timing Diagram
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
5
Doc. No. MD-5028 Rev. C
CAT4016
TYPICAL PERFORMANCE CHARACTERISTICS
VDD = 5.0V, LED current 30mA, all LEDs On, TAMB = 25°C unless otherwise specified.
LED Current vs. LED Pin Voltage
Supply Current vs. VDD Pin Voltage
70
6.0
5.5
5.0
4.5
4.0
3.5
3.0
All LED's ON
60
50
40
30
20
10
0
All LED's OFF
0.0
0.3
0.6
0.9
1.2
1.5
5.5
5.5
3.0
3.5
4.0
VDD [V]
4.5
5.0
5.5
LED PIN [V]
LED Current vs. VDD Pin Voltage
Supply Current vs. RSET Current
12
31.5
All LED's ON
31.0
30.5
30.0
29.5
29.0
28.5
10
8
6
4
All LED's OFF
2
0
3.0
3.5
4.0
VDD [V]
4.5
5.0
0.0
0.5
1.0
1.5
2.0
RSET CURRENT [mA]
RSET Voltage vs. VDD Pin Voltage
LED Current vs. RSET Resistor
1.30
100
80
60
40
20
0
1.25
1.20
1.15
1.10
3.0
3.5
4.0
4.5
5.0
0.1
1.0
10.0
100.0
VDD [V]
RSET [kΩ]
Doc. No. MD-5028 Rev. C
6
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT4016
TYPICAL PERFORMANCE CHARACTERISTICS
DD = 5.0V, LED current 30mA, all LEDs On, TAMB = 25°C unless otherwise specified.
V
RSET Voltage vs. Temperature
1.30
LED Current vs. Temperature
31.5
31.0
30.5
30.0
29.5
29.0
28.5
1.25
1.20
1.15
1.10
-50
0
50
100
TEMPERATURE [°C]
150
-50
0
50
100
150
TEMPERATURE [°C]
Internal Pull-Down Current (LATCH pin)
Internal Pull-Up Current (BLANK pin)
30
30
25
20
15
10
5
25
20
15
10
5
0
0
0
1
2
3
4
5
0
1
2
3
4
5
BLANK VOLTAGE [V]
LATCH VOLTAGE [V]
BLANK Transient Response
PWM Dimming on BLANK pin (f = 10kHz)
100
80
60
40
20
0
0
5
10
15
20
25
30
LED CURRENT [mA]
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
7
Doc. No. MD-5028 Rev. C
CAT4016
PIN DESCRIPTION
Name
GND
Function
Ground
SIN
Serial data input pin
CLK
Serial clock input pin
LATCH
LED1-LED16
BLANK
SOUT
RSET
VDD
Latch serial data to output registers
LED channel 1 to 16 cathode terminals
Enable / disable all channels
Serial data output pin.
LED current set pin
Positive supply Voltage
TAB (TQFN
package only)
Connect to GND on the PCB
PIN FUNCTION
GND is the ground reference pin for the device. This
pin must be connected to the ground plane on the
PCB.
BLANK is the LED channel enable and disable input
pin. When low, LEDs are enabled according to the
output latch register content. When high, all LEDs are
off, while preserving the data in the output latch
register.
SIN is the serial data input. Data is loaded into the
internal register on each rising edge of CLK.
SOUT is the serial data output of the 16-bit serial shift
register. This pin is used to cascade several devices
on the serial bus. The SOUT pin is then connected to
the SIN input of the next device on the serial bus to
cascade.
CLK is the serial clock input. On each rising CLK
edge, data is transferred from SIN to the internal 16-
bit serial shift register.
LATCH is the latch data input. On the rising edge of
LATCH, data is loaded from the 16-bit serial shift
register into the output register latch. On the falling
edge, this data is latched in the output register and
isolated from the state of the serial shift register.
RSET is the LED current setting pin. A resistor is
connected between this pin and ground. Each LED
channel current is set to 50 times the current pulled
out of the pin. The RSET pin voltage is regulated to
1.2V.
LED1 - LED16 are the LED current sink channels.
These pins are connected to the LED cathodes. The
current sinks drive the LEDs with a current equal to 50
times RSET pin current. For the LED sink to operate
correctly, the voltage on the LED pin must be above
0.4V.
VDD is the positive supply pin voltage for the entire
device. A small 1µF ceramic is recommended close
to pin.
Doc. No. MD-5028 Rev. C
8
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT4016
BLOCK DIAGRAM
LED1 LED2 LED3
LED16
VDD
VIN
+
CURRENT
SINKS
RSET
GND
Current
Setting
BLANK
LATCH
1.2V Ref
LATCHES
L1
S1
L2
S2
L3
S3
L16
S16
SHIFT
REGISTER
SOUT
SIN
CLK
Figure 2. CAT4016 Functional Block Diagram
BASIC OPERATION
The CAT4016 uses 16 tightly matched current sinks to
accurately regulate the LED current in each channel.
The external resistor, RSET, is used to set the LED
Pull-up and pull-down resistors are internally provided
to set the state of the BLANK and LATCH pins to the
off-state when not externally driven.
channel current to 50 times the current in RSET
.
SERIAL INTERFACE
1.2
A high-speed serial 4-wire interface is provided to
program the state of each LED on or off. The
interface contains a 16-bit serial to parallel shift
LEDcurrent = 50×
RSET
Tight current regulation for all channels is possible
over a wide range of input and LED voltages due to
independent current sensing circuitry on each
channel. The LED channels have a maximum dropout
of 0.4V for most current and supply voltage
conditions. This helps improve the heat dissipation
and efficiency of the LED driver.
register (S1-S16) and
a 16-bit latch (L1-L16).
Programming the serial to parallel register is
accomplished via SIN and CLK input pins. On each
rising edge of the CLK signal, the data from SIN is
moved through the shift register serially. Data is also
moved out of SOUT which can be connected to a next
device if programming more then one device on the
same interface.
Upon power-up, an under-voltage lockout circuit
clears all latches and shift registers and sets all
outputs to off. Once the under-voltage lockout
threshold has been reached the device can be
programmed.
On the rising edge of LATCH, the data contents of the
serial to parallel shift register is reflected in the
latches. On the falling edge of LATCH, the state of the
serial to parallel register at that particular time is
saved in the latches and does not change irrespective
of the contents of the serial to parallel register.
The driver delays the activation of each consecutive
LED output channel by 17ns (typical). Relative to
LED1, LED2 is delayed by 17ns, LED3 by 34ns and
LED16 by 250ns typical. The delay is introduced when
LATCH is activated. The delay minimizes the inrush
current on the LED supply by staggering the turn on
and off current spikes over a period of time and
therefore allowing usage of smaller bypass capacitors.
BLANK is used to disable all LEDs (turn off)
simultaneously while maintaining the same data in the
latch register. When low, the LED outputs reflect the
data in the latches. When high, all outputs are high
impedance (zero current).
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
9
Doc. No. MD-5028 Rev. C
CAT4016
PACKAGE OUTLINE DRAWINGS
SOIC 24-Lead 300mils (W)(1)
SYMBOL
MIN
2.35
0.10
2.05
0.31
0.20
15.20
10.11
7.34
NOM
MAX
2.65
0.30
2.55
0.51
0.33
15.40
10.51
7.60
A
A1
A2
b
E1
E
c
D
E
E1
e
1.27 BSC
h
0.25
0.40
0°
0.75
1.27
8°
b
e
L
θ
PIN#1 IDENTIFICATION
θ1
5°
15°
TOP VIEW
h
D
h
θ1
A2
θ
A
θ1
L
c
A1
SIDE VIEW
END VIEW
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MS-013.
Doc. No. MD-5028 Rev. C
10
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT4016
TSSOP 24-Lead 4.4mm (Y)(1)
b
SYMBOL
MIN
NOM
MAX
1.20
0.15
1.05
0.30
0.20
7.90
6.55
4.50
A
A1
A2
b
0.05
0.80
0.19
0.09
7.70
6.25
4.30
c
E1
E
D
7.80
6.40
E
E1
e
4.40
0.65 BSC
1.00 REF
0.60
L
L1
θ1
0.50
0°
0.70
8°
e
TOP VIEW
D
c
A2
A1
A
θ1
L1
L
SIDE VIEW
END VIEW
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-153.
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
11
Doc. No. MD-5028 Rev. C
CAT4016
QSOP 24-Lead (VS, VSR)(1)
D
SYMBOL
MIN
NOM
MAX
1.73
0.25
0.31
0.25
8.74
6.19
3.98
A
A1
b
1.37
0.10
0.20
0.19
8.56
5.82
3.81
c
D
E
E1
E
E1
e
0.635 BSC
h
0.28
0.41
0.48
0.86
L
L2
ө1
ө2
0.254 BSC
7º BSC
0º
8º
e
b
TOP VIEW
θ2
h
A
θ1
L
c
L2
A1
END VIEW
SIDE VIEW
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-137.
Doc. No. MD-5028 Rev. C
12
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT4016
TQFN 24-Pad 4 x 4mm (HV6)(1
A
D
DETAIL A
E
E2
PIN#1 ID
D2
PIN#1 INDEX AREA
A1
SIDE VIEW
TOP VIEW
BOTTOM VIEW
b
e
SYMBOL
MIN
NOM
0.75
MAX
0.80
0.05
L
A
A1
A3
b
0.70
0.00
0.02
DETAIL A
0.20 REF
0.25
0.18
3.90
2.40
3.90
2.40
0.30
4.10
2.90
4.10
2.90
D
4.00
D2
E
–
4.00
A
E2
e
–
0.50 BSC
0.40
A3
L
0.30
0.50
FRONT VIEW
)
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-220.
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
13
Doc. No. MD-5028 Rev. C
CAT4016
EXAMPLE OF ORDERING INFORMATION(1)
Prefix
Device #
Suffix
CAT
4016
HV6
– G
T2
Product Number
Tape & Reel
T: Tape & Reel
1: 1,000/Reel (5)
2: 2,000/Reel
4016
Package
W: SOIC
Optional
Company ID
Lead Finish
Blank: Matte-Tin
G: NiPdAu
Y: TSSOP
VS: QSOP
VSR: QSOP(4)
HV6: TQFN
For Product Top Mark Codes, click here:
http://www.catsemi.com/techsupport/producttopmark.asp
Notes:
(1) All packages are RoHS-compliant (Lead-free, Halogen-free).
(2) The device used in the above example is a CAT4016HV6–GT2 (TQFN, NiPdAu, Tape & Reel, 2,000/Reel).
(3) For additional package and temperature options, please contact your nearest Catalyst Semiconductor Sales office.
(4) Different pin outs, see page 2.
(5) SOIC package availability in 1,000/Reel. All other packages are 2,000/Reel.
Doc. No. MD-5028 Rev. C
14
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
REVISION HISTORY
Date
Rev. Reason
09/26/2007
10/17/2007
A
B
Initial Issue
Update Absolute Maximum Ratings
Update Ordering Information table, added TQFN in NiPdAu plated finish.
Update Package Outline Drawings
Update Example of Ordering Information
Add Top Mark Codes link
04/09/2008
C
Copyrights, Trademarks and Patents
© Catalyst Semiconductor, Inc.
Trademarks and registered trademarks of Catalyst Semiconductor include each of the following:
Adaptive Analog™, Beyond Memory™, DPP™, EZDim™, LDD™, MiniPot™, Quad-Mode™ and Quantum Charge Programmable™
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR
THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY
ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where
personal injury or death may occur.
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled
"Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical
semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc.
Corporate Headquarters
2975 Stender Way
Santa Clara, CA 95054
Phone: 408.542.1000
Fax: 408.542.1200
www.catsemi.com
Document No: MD-5028
Revision:
C
Issue date:
04/09/08
相关型号:
©2020 ICPDF网 联系我们和版权申明