CAT808NTFI-32-T3 [ONSEMI]
1-CHANNEL POWER SUPPLY SUPPORT CKT, PSSO3, HALOGEN FREE AND ROHS COMPLIANT, SOT-89, 3 PIN;型号: | CAT808NTFI-32-T3 |
厂家: | ONSEMI |
描述: | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PSSO3, HALOGEN FREE AND ROHS COMPLIANT, SOT-89, 3 PIN |
文件: | 总6页 (文件大小:91K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CAT808
Low-Power Precision
Voltage Detector
Description
The CAT808 is a high−precision voltage detector designed for
monitoring single cell and multi−cell batteries. Voltage detection
thresholds between 2.0 V and 3.5 V are provided with 0.1 V resolution
and 3.0% accuracy.
http://onsemi.com
The CAT808 open−drain output is active low until the V voltage
DD
exceeds the detection threshold. A low hysteresis is built into the
5
1
device to minimize output “chatter”, while V
passes through the
DD
detection threshold, and the output transitions high.
After the CAT808 asserts the output high condition, it continues to
TSOT−5
TD SUFFIX
CASE 419AE
monitor V until it drops below the detection threshold, when the
DD
output goes low until V once again exceeds the detection threshold.
DD
Features
MARKING DIAGRAM
• Ultra Low Current Consumption 2.4 mA
• Accurate Voltage Detection Threshold
• Fine Voltage Detection Threshold Resolution
• Open Drain Output (Active Low)
TLYM
TL
Y
M
= Specific Device Code
= Production Year
= Production Month
• Industrial Temperature Range −40°C to +85°C
• 5−pin TSOT−23
• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
PIN CONNECTIONS
Compliant
1
Applications
OUT
NC
NC
• Battery−Powered Systems
• Power Supply Monitoring
• Handheld and Portable Equipment
• Processor Supervisor Reset
V
DD
GND
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
IN
V
DD
DC−DC
CONVERTER
CAT808
OUT
GND
10 kW
Battery
Voltage
SHDN OUT
GND
Note: The value of the pull−up resistor is not critical
Figure 1. Typical Application
©
Semiconductor Components Industries, LLC, 2011
1
Publication Order Number:
September, 2011 − Rev. 6
CAT808/D
CAT808
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameters
Ratings
Units
°C
Temperature under Bias
−55 to +125
−65 to +150
Storage Temperature
°C
Voltage on any Pin with Respect to GND (Notes 1, 2)
−2.0 to V + 2.0
V
DD
V
with Respect to GND
−2.0 to 7.0
+300
V
DD
Lead Soldering temperature (10 seconds)
Power Dissipation
°C
250
mW
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The Minimum DC input voltage is −0.5 V. During transitions, inputs may undershoot to −2.0 V for periods of less than 20 ns. Maximum DC
voltage on output pins is V +0.5 V, which may overshoot to V +2.0 V for periods of less than 20 ns.
CC
CC
2. Latch−up protection is provided for stresses up to 100 mA on all pins from −1 V to V +1 V.
CC
Table 2. RECOMMENDED OPERATING CONDITIONS
Parameters
Ratings
+1.2 to +6.0
−40 to +85
Units
V
V
DD
Operating Temperature Range
°C
Table 3. DC ELECTRICAL CHARACTERISTICS (T = −40°C to +85°C, V = 1.2 V to 6.0 V)
A
DD
Symbol
Parameter
Conditions
Min
2.43
2.62
3.12
3.42
−
Typ
2.5
2.7
3.2
3.5
2.4
3.5
5
Max
2.57
2.78
3.28
3.58
5
Units
V
DET
Detection Voltage
CAT808Nxxx−25
CAT808Nxxx−27
CAT808Nxxx−32
CAT808Nxxx−35
V
I
Current Consumption
Output Sink Current
V
DD
V
DD
V
DD
= 4.0 V
= 5.0 V
= 6.0 V
mA
DD
−
7
−
10
I
V
= 0.5 V
V
DD
V
DD
= 1.2 V
= 2.4 V
0.6
2.9
−
1.4
5
−
mA
OUT
DS
−
I
Output Leakage Current
Response Time
V
= 5.0 V, V = 5.0 V
−
1
mA
ms
LEAK
DS
DD
T
–
−
−
60
PHL/LH
DV
DT • V
Detection Voltage Temperature
Coefficient (Note 3)
−
10
100
ppm/°C
DET
(typ)
A
DET
3. The temperature change ratio in the detection voltage [ppm/°C] is calculated by using the following equation:
DVDET
1, 000, 000[ppmńoC]
DTA @ VDET(typ)
http://onsemi.com
2
CAT808
Operation – Voltage Detector
The CAT808 has an active low output that asserts (pulls
low) when the supply voltage drops below the detection
OUT
V
DD
threshold voltage (V
). The open−drain output requires
DET
an external pull−up resistor between the output pin and the
supply voltage (as shown in the typical application
diagram). On power−up, OUT is held active low until the
VOLTAGE
REFERENCE
supply voltage (V ) rises above V . While V is above
DD
DET
DD
Figure 2. Block Diagram
V
DET
, OUT stays high until V drops below V , then
DD DET
OUT once again goes low.
V
DD
*
V
V
DET(MAX)
DET(MAX)
V
DET
V
DET
V
V
DET(MIN)
DET(MIN)
GND
T
PLH
V
OH
T
PHL
OUT Slews with V
DD
OUT
* Voltage of V below 1 volt will not be able to maintain low output.
DD
Figure 3. Timing Diagram
Table 4. PIN FUNCTIONS
Pin
Function
V
Voltage Input and Power Supply
Ground Pin
DD
GND
OUT
NC
Active Low Open Drain output
No Connect, the pin is electrically open
http://onsemi.com
3
CAT808
TYPICAL ELECTRICAL OPERATING CHARACTERISTICS (Typical values at T = 25°C)
A
5
4
3
2
2.710
2.705
2.700
2.695
1
0
2
3
4
5
6
−40
−5
30
65
100
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
Figure 4. VDD Supply Current vs. VDD Supply
Voltage
Figure 5. VDET Detection Voltage vs.
Temperature
100
10
10
T
−40°C
8
6
4
PLH
+25°C
+90°C
1
0.1
T
PHL
2
0
0.01
0.001
0.01
0.1
1
10
100
1.0
1.5
2.0
2.5
LOAD CAPACITANCE (nF)
V
DD
(V)
Figure 6. Response Time vs. Load
Capacitance
Figure 7. IOUT Transistor Output Current vs.
DD Supply Voltage
V
http://onsemi.com
4
CAT808
PACKAGE DIMENSIONS
TSOT−23, 5 LEAD
CASE 419AE−01
ISSUE O
SYMBOL
MIN
NOM
MAX
1.00
0.10
0.90
0.45
0.20
D
A
A1
A2
b
e
0.01
0.80
0.30
0.12
0.05
0.87
c
0.15
D
2.90 BSC
2.80 BSC
1.60 BSC
0.95 TYP
0.40
E1
E
E
E1
e
L
0.30
0.50
L1
L2
θ
0.60 REF
0.25 BSC
0º
8º
TOP VIEW
A2 A
q
L
b
c
A1
L2
L1
SIDE VIEW
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-193.
http://onsemi.com
5
CAT808
Ordering Information
Table 5. ORDERING INFORMATION
Specific Device
Temperature
†
Orderable Part Number
Package
Lead Finish
Shipping
Marking
Range
CAT808NTDI−25GT3
CAT808NTDI−27GT3
CAT808NTDI−32GT3
CAT808NTDI−35GT3
TL
TSOT−23−5
TSOT−23−5
TSOT−23−5
TSOT−23−5
Industrial
Industrial
Industrial
Industrial
NiPdAu
NiPdAu
NiPdAu
NiPdAu
3000 Units / Tape & Reel
3000 Units / Tape & Reel
3000 Units / Tape & Reel
3000 Units / Tape & Reel
TL
TL
TL
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
CAT808/D
相关型号:
CAT808NTFI-35T3
Power Supply Support Circuit, Fixed, 1 Channel, +3.5VV, PSSO3, ROHS COMPLIANT, SOT-89, 3 PIN
ONSEMI
©2020 ICPDF网 联系我们和版权申明