FPF2124 [ONSEMI]
全功能负载开关，带可调节电流限制;
| 型号： | FPF2124 |
| 厂家： | 
ONSEMI |
| 描述： | 全功能负载开关，带可调节电流限制 开关 PC 驱动 光电二极管 接口集成电路 驱动器 |
| 文件： | 总13页 (文件大小：1931K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
IntelliMAXt Advanced Load
Management Product
FPF2123-FPF2125
Description
The FPF2123, FPF2124, and FPF2125 are a series of load switches
which provide full protection to systems and loads which may
encounter large current conditions. These devices contain a 0.125 W
current−limited P−channel MOSFET which can operate over an input
voltage range of 1.8−5.5 V. The current limit is settable using
an external resistor. Internally, current is prevented from flowing
when the MOSFET is off and the output voltage is higher than the
input voltage. Switch control is by a logic input (ON) capable
of interfacing directly with low voltage control signals. Each part
contains thermal shutdown protection which shuts off the switch
to prevent damage to the part when a continuous over−current
condition causes excessive heating.
When the switch current reaches the current limit, the parts operate
in a constant−current mode to prohibit excessive currents from
causing damage. For the FPF2123 and FPF2124 if the constant current
condition still persists after 10 ms, these parts will shut off the switch.
The FPF2123 has an auto−restart feature which will turn the switch on
again after 160 ms if the ON pin is still active. The FPF2124 does not
have this auto−restart feature so the switch will remain off after
a current limit fault until the ON pin is cycled. The FPF2125 will not
turn off after a current limit fault, but will rather remain in the constant
current mode indefinitely. The minimum current limit is 150 mA.
These parts are available in a space−saving 5 pin SOT23 package.
www.onsemi.com
SOT23−5
CASE 527AH
MARKING DIAGRAM
&E&E&Y
&O212X&C
&.&O&E&V
&E
&Y
&O
= Designates Space
= Binary Calendar Year Coding Scheme
= Plant Code identifier
212X = Device Specific Code
X = 3. 4 or 5
Features
&C
&.
&V
= Single digit Die Run Code
= Pin One Dot
= Eight−Week Binary Datecoding Scheme
• 1.8 to 5.5 V Input Voltage Range
• Controlled Turn−On
• 0.15−1.5 A Adjustable Current Limit
• Under−Voltage Lockout
• Thermal Shutdown
• < 2 mA Shutdown Current
• Auto Restart
ORDERING INFORMATION
See detailed ordering and shipping information on page 11 of
this data sheet.
• Fast Current Limit Response Time
♦ 3 ms to Moderate Over Currents
• Fault Blanking
• Reverse Current Blocking
• These Devices are Pb−Free and are RoHS Compliant
Applications
• PDAs
• Cell Phones
• GPS Devices
• MP3 Players
• Digital Cameras
• Peripheral Ports
• Hot Swap Supplies
© Semiconductor Components Industries, LLC, 2008
1
Publication Order Number:
May, 2021 − Rev. 6
FPF2125/D
FPF2123−FPF2125
Typical Application Circuit
TO LOAD
V
OUT
V
IN
FPF2123−FPF2125
ON ISET
OFF ON
+
GND
−
Figure 1. Typical Application
Functional Block Diagram
V
IN
UVLO
REVERSE
CURRENT
BLOCKING
ON
CONTROL
LOGIC
CURRENT
LIMT
V
OUT
THERMAL
SHUTDOWN
ISET
GND
Figure 2. Block Diagram
Pin Configuration
V
1
2
3
5
4
V
IN
OUT
GND
ON
ISET
SOT23−5
Figure 3. Pin Assignment
www.onsemi.com
2
FPF2123−FPF2125
PIN DESCRIPTIONS
Pin
1
Name
Function
V
IN
Supply Input: Input to the power switch and the supply voltage for the IC
2
GND
ON
Ground
3
ON Control Input
4
ISET
Current Limit Set Input: A resistor from ISET to ground sets the current limit for the switch.
Switch Output: Output of the power switch
5
V
OUT
ABSOLUTE MAXIMUM RATINGS
Parameter
Min
Max
6.0
Unit
V
V
IN
, V , ON, ISET to GND
OUT
−0.3
Power Dissipation @ T = 25°C (Note 1)
667
125
150
150
mW
°C
A
Operating Temperature Range
Storage Temperature
−40
−65
°C
Thermal Resistance, Junction to Ambient
Electrostatic Discharge Protection
°C/W
V
HBM
MM
4000
400
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Package power dissipation on 1 square inch pad, 2 oz copper board.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
1.8
Max
5.5
85
Unit
V
V
IN
Input Voltage
Ambient Operating Temperature
T
A
−40
°C
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
ELECTRICAL CHARACTERISTICS
V
IN
= 1.8 to 5.5 V, T = −40 to +85°C unless otherwise noted. Typical values are at V = 3.3 V and T = 25°C.
A
I
N
A
Symbol
Parameter
Test Condition
Min
Typ
Max
Unit
BASIC OPERATION
V
Operating Voltage
1.8
5.5
V
IN
Q
I
Quiescent Current
I
= 0 mA
V
V
= 1.8 to 3.3 V
= 3.3 to 5.5 V
75
80
mA
OUT
IN
120
2
IN
I
Shutdown Current
mA
mA
SHDN
I
Reverse Block Leakage Current
Latch−Off Current
1
BLOCK
I
FPF2124
50
mA
LATCHOFF
R
ON−Resistance
V
IN
V
IN
V
IN
V
IN
V
IN
V
IN
V
IN
= 3.3 V, I
= 3.3 V, I
= 3.3 V, I
= 1.8 V
= 5.5 V
= 1.8 V
= 5.5 V
= 50 mA, T = 25°C
125
150
160
200
200
mW
ON
OUT
OUT
OUT
A
= 50 mA, T = 85°C
A
= 50 mA, T = −40°C to + 85°C
65
A
V
ON Input Logic High Voltage (ON)
ON Input Logic Low Voltage (ON)
0.75
1.30
V
V
IH
V
0.5
1.0
IL
www.onsemi.com
3
FPF2123−FPF2125
ELECTRICAL CHARACTERISTICS (continued)
V
IN
= 1.8 to 5.5 V, T = −40 to +85°C unless otherwise noted. Typical values are at V = 3.3 V and T = 25°C.
A
IN
A
Symbol
Parameter
Test Condition
Min
600
1.5
Typ
Max
Unit
BASIC OPERATION
ON Input Leakage
Off Switch Leakage
PROTECTIONS
Current Limit
V
V
= V or GND
1
1
mA
mA
ON
IN
I
= 0 V, V
= 0 V
SWOFF
ON
OUT
I
V
V
= 3.3 V, V
= 3.3 V, V
= 3.0 V, RSET = 576 W
800
150
140
130
10
1000
mA
mA
°C
LIM
IN
OUT
I
Min. Current Limit
Thermal Shutdown
= 3.0 V
LIM(min.)
IN
OUT
Shutdown Threshold
Return from Shutdown
Hysteresis
UVLO
Under Voltage Shutdown
V
IN
Increasing
1.6
50
1.7
V
Under Voltage Shutdown
Hysteresis
mV
DYNAMIC
t
Turn On Time
Turn Off Time
R = 500 W, C = 0.1 mF
25
70
ms
ms
ON
L
L
t
R = 500 W, C = 0.1 mF
L L
OFF
t
V
Rise Time
Fall Time
R = 500 W, C = 0.1 mF
12
ms
R
OUT
OUT
L
L
t
V
R = 500 W, C = 0.1 mF
200
10
ms
F
L
L
t
Over Current Blanking Time
FPF2123, FPF2124
FPF2123
5
20
ms
ms
BLANK
t
Auto−Restart Time
80
160
NA
3
320
RESTART
FPF2124, FPF2125
Short Circuit Response Time
V
= V = 3.3 V
ms
ms
IN ON
Moderate Over−Current Conditions
V
= V = 3.3 V
20
IN
ON
Hard Short
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
4
FPF2123−FPF2125
TYPICAL CHARACTERISTICS
76
74
72
70
68
66
64
62
95
85
75
V
= V
IN
ON
V
IN
= 3.3 V
V
IN
= 5.5 V
65
55
45
V
IN
= 1.8 V
−40
−15
10
35
60
85
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
T , JUNCTION TEMPERATURE (°C)
J
SUPPLY VOLTAGE (V)
Figure 4. Quiescent Current vs. Input Voltage
Figure 5. Quiescent Current vs. Temperature
2400
2100
1800
1500
1200
900
500
450
400
350
300
250
200
150
100
50
V
= 5.5 V
IN
V
= 5.5 V
IN
V
IN
= 3.3 V
600
V
= 3.3 V
IN
300
0
−40
0
−40
−15
10
35
60
85
−15
10
35
60
85
T , JUNCTION TEMPERATURE (°C)
J
T , JUNCTION TEMPERATURE (°C)
J
Figure 6. ISHUTDOWN Current vs. Temperature
Figure 7. ISWITCH−OFF Current vs. Temperature
0.21
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0.18
0.15
0.12
0.09
0.06
0.03
0.00
V
IN
= 5.5 V
V
IN
= 3.3 V
−40
−15
10
35
60
85
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
T , JUNCTION TEMPERATURE (°C)
J
Figure 8. Reverse Current vs. VOUT
Figure 9. Reverse Current vs. Temperature
www.onsemi.com
5
FPF2123−FPF2125
TYPICAL CHARACTERISTICS (Continued)
900
52.0
51.5
V
R
− V
= 0.3 V
IN
OUT
= 576
SET
860
820
780
740
700
51.0
50.5
50.0
49.5
49.0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
−40
−15
10
35
60
85
V
IN
, INPUT VOLTAGE (V)
T , JUNCTION TEMPERATURE (°C)
J
Figure 10. ILATCH−OFF Current vs. Temperature
Figure 11. Current Limit vs. Input Voltage
900
860
820
780
740
700
1800
1500
1200
900
600
300
0
R
= 576
SET
200
800
1400
2000
(W)
2600
3200
−40
−15
10
35
60
85
T , JUNCTION TEMPERATURE (°C)
J
R
SET
Figure 12. Current Limit vs. Temperature
Figure 13. Current Limit vs. Rest
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
170
160
150
140
130
120
110
100
1
2
3
4
5
6
1
2
3
4
5
6
V
IN
, INPUT VOLTAGE (V)
V
IN
, INPUT VOLTAGE (V)
Figure 14. VIH vs. VIN
Figure 15. RON vs. VIN
www.onsemi.com
6
FPF2123−FPF2125
TYPICAL CHARACTERISTICS (Continued)
200
180
160
140
120
100
80
100
V
IN
= 1.8 V
T
OFF
V
IN
= 3.3 V
T
ON
V
IN
= 5.5 V
V
= 3.3 V
IN
R = 500 W
C
L
= 0.1 mF
OUT
60
−40
10
−40
−15
10
35
60
85
85
85
−15
10
35
60
85
T , JUNCTION TEMPERATURE (°C)
J
T , JUNCTION TEMPERATURE (°C)
J
Figure 16. R(ON) vs. Temperature
Figure 17. TON/TOFF vs Temperature
1000
100
10
14
13
12
11
10
9
T
FALL
T
RISE
V
= 3.3 V
R = 500 W
IN
L
C
= 0.1 mF
OUT
1
−40
8
−40
−15
10
35
60
−15
10
35
60
85
T , JUNCTION TEMPERATURE (°C)
J
T , JUNCTION TEMPERATURE (°C)
J
Figure 19. TBLANK vs. Temperature
Figure 18. TRISE/TFALL vs. Temperature
200
190
180
170
160
150
140
130
120
2
V
DRV
V
IN
= 3.3 V
2 V/DIV
R = 2.2 W
L
C
C
= 10 mF
= 0.1 mF
IN
OUT
V
OUT
2 V/DIV
I
OUT
400 mA/DIV
−40
−15
10
35
60
T , JUNCTION TEMPERATURE (°C)
J
Figure 20. TRESTART vs. Temperature
Figure 21. TBLANK Response
www.onsemi.com
7
FPF2123−FPF2125
TYPICAL CHARACTERISTICS (Continued)
2
V
DRV
V
ON
V
IN
= 3.3 V
2 V/DIV
V
= 3.3 V
IN
2 V/DIV
R = 500 W
R = 2.2 W
L
L
C
C
= 10 mF
= 0.1 mF
C
C
= 10 mF
= 0.1 mF
IN
OUT
IN
OUT
V
OUT
2 V/DIV
I
OUT
10 mA/DIV
I
OUT
400 mA/DIV
Figure 23. TON Response
Figure 22. TRESTART Response
V
ON
V
= 3.3 V
IN
V
IN
2 V/DIV
R = 500 W
C
C
L
2 V/DIV
C
C
= 10 mF
IN
= 10 mF
IN
OUT
= 0.1 mF
OUT
= 0.1 mF
I
OUT
I
OUT
4 A/DIV
10 mA/DIV
V
OUT
2 V/DIV
Figure 25. Short Circuit Response
(Output Shorted to GND)
Figure 24. TOFF Response
V
IN
2 V/DIV
C
C
= 10 mF
= 0.1 mF
R = 2.2 W
IN
L
V
= V
ON
2 V/DIV
IN
C
C
= 10 mF
= 0.1 mF
OUT
IN
OUT
V
ON
2 V/DIV
I
OUT
400 mA/DIV
I
OUT
400 mA/DIV
Figure 26. Current Limit Response
(Switch Power Up to Hard Short)
Figure 27. Current Limit Response
(Output Shorted to GND by 2.2 W, Moderate Short)
NOTE:
V
DRV
signal forces the device to go into overcurrent condition by loading a 2.2 W resistor.
www.onsemi.com
8
FPF2123−FPF2125
Description of Operation
Current Limiting
The FPF2123, FPF2124, and FPF2125 are current limited
switches that protect systems and loads which can be
damaged or disrupted by the application of high currents.
The core of each device is a 0.125 W P−channel MOSFET
and a controller capable of functioning over a wide input
operating range of 1.8−5.5 V. The controller protects against
The current limit ensures that the current through the
switch doesn’t exceed a maximum value while not limiting
at less than a minimum value. The current at which the parts
will limit is adjustable through the selection of an external
resistor connected to ISET. Information for selecting the
resistor is found in the Application Info section. The
FPF2123 and FPF2124 have a blanking time of 10 ms,
nominally, during which the switch will act as a constant
current source. At the end of the blanking time, the switch
will be turned−off. The FPF2125 has no current limit
blanking period so it will remain in a constant current state
until the ON pin is deactivated or the thermal shutdown
turns−off the switch.
system
malfunctions
through
current
limiting
under−voltage lockout and thermal shutdown. The current
limit is adjustable from 150 mA to 1.5 A through the
selection of an external resistor.
On/Off Control
The ON pin controls the state of the switch. When ON is
high, the switch is in the on state. Activating ON
continuously holds the switch in the on state so long as there
Under−Voltage Lockout
is no fault. For all versions, an under−voltage on V or a
The under−voltage lockout turns−off the switch if the
input voltage drops below the under−voltage lockout
threshold. With the ON pin active, the input voltage rising
above the under−voltage lockout threshold will cause a
controlled turn−on of the switch which limits current
over−shoots.
IN
junction temperature in excess of 140°C overrides the ON
control to turn off the switch. In addition, excessive currents
will cause the switch to turn off in the FPF2123 and
FPF2124. The FPF2123 has an Auto−Restart feature which
will automatically turn the switch on again after 160 ms. For
the FPF2124, the ON pin must be toggled to turn−on the
switch again. The FPF2125 does not turn off in response to
an over current condition but instead remains operating in a
constant current mode so long as ON is active and the
thermal shutdown or under−voltage lockout have not
activated.
Thermal Shutdown
The thermal shutdown protects the die from internally or
externally generated excessive temperatures. During an
over−temperature condition the switch is turned−off. The
switch automatically turns−on again if the temperature of
the die drops below the threshold temperature.
The ON pin control voltage and V pin have independent
IN
recommended operating ranges. The ON pin voltage can be
driven by a voltage level higher than the input voltage.
www.onsemi.com
9
FPF2123−FPF2125
APPLICATIONS INFORMATION
V
OUT
V
IN
FPF2123−FPF2125
R2 = 110 W
OFF ON
C1 = 4.7 mF
ON
ISET
Battery
5.5 V
+
GND
C2 = 0.1 mF
−
5.5 V MAX
R
SET
Figure 28. Typical Application
Setting Current Limit
The FPF2123, FPF2124, and FPF2125 have a current
limit which is set with an external resistor connected
between ISET and GND. This resistor is selected by using
the following equation (1),
value, C
, to prevent the part from registering an
OUT(max)
over−current condition and turning−off the switch. The
maximum output capacitance can be determined from the
following formula,
460
ILIM
ILIM(min) tBLANK(min)
RSET
+
(eq. 1)
(eq. 2)
COUT(max) +
VIN
R
SET
is in Ohms and that of I
is Amps.
LIM
The table below can also be used to select R . A typical
application would be the 500 mA current that is required by
a single USB port. Using the table below an appropriate
SET
Table 1. Current Limit Various RSET Values
Min. Current Typ. Current Max. Current
Limit [mA]
1120
1010
920
Limit [mA]
1490
1350
1230
1120
1010
920
Limit [mA]
1860
1690
1540
1400
1270
1150
1050
1000
950
R
[W]
SET
selection for the R
resistor would be 604 W. This will
SET
309
ensure that the port load could draw 570 mA, but not more
than 950 mA. Likewise for a dual port system, an R of
340
374
SET
340 W would always deliver at least 1120 mA and never
more than 1860 mA.
412
840
Input Capacitor
453
760
To limit the voltage drop on the input supply caused by
transient in−rush currents when the switch turns−on into a
discharged load capacitance or a short−circuit, a capacitor
499
690
549
630
840
needs to be placed between V and GND. A 4.7 mF ceramic
576
600
800
IN
capacitor, C , must be placed close to the V pin. A higher
IN
IN
604
570
760
value of C can be used to further reduce the voltage drop
IN
732
470
630
790
experienced as the switch is turned on into a large capacitive
load.
887
390
520
650
1070
1300
1910
3090
320
430
540
Output Capacitor
A 0.1 mF capacitor, C
260
350
440
, should be placed between
OUT
V
OUT
and GND. This capacitor will prevent parasitic board
180
240
300
inductances from forcing V
switch turns−off. For the FPF2123 and FPF2124, the total
below GND when the
OUT
110
150
190
output capacitance needs to be kept below a maximum
www.onsemi.com
10
FPF2123−FPF2125
Power Dissipation
output is present will cause the temperature of the part to
increase. The junction temperature will only be able to
increase to the thermal shutdown threshold. Once this
temperature has been reached, toggling ON will not turn−on
the switch until the junction temperature drops. For the
FPF2125, a short on the output will cause the part to operate
in a constant current state dissipating a worst case power of,
During normal operation as a switch, the power dissipated
in the part will depend upon the level at which the current
limit is set. The maximum allowed setting for the current
limit is 1.5 A and this will result in a typical power
dissipation of,
2
P + (ILIM
)
RON + (1.5)2 0.125 + 281 mW
(eq. 3)
P(max) + VIN(max) ILIM(max) + 5.5 1.5 + 8.25 W
If the part goes into current limit the maximum power
dissipation will occur when the output is shorted to ground.
For the FPF2123 the power dissipation will scale by the
(eq. 5)
This large amount of power will activate the thermal
shutdown and the part will cycle in and out of thermal
shutdown so long as the ON pin is active and the short is
present.
Auto−Restart Time, t , and the Over Current
RESTART
Blanking Time, t , so that the maximum power
BLANK
dissipated is,
tBLANK(max)
tRESTART(min) ) tBLANK(max)
Board Layout
P(max) +
For best performance, all traces should be as short as
possible. To be most effective, the input and output
capacitors should be placed close to the device to minimize
the effects that parasitic trace inductances may have on
normal and short−circuit operation. Using wide traces for
20
VIN(max) ILIM(max) +
5.5 1.5 + 1.65 W
80 ) 20
(eq. 4)
This is more power than the package can dissipate, but the
thermal shutdown of the part will activate to protect the part
from damage due to excessive heating. When using the
FPF2124, attention must be given to the manual resetting of
the part. Continuously resetting the part when a short on the
V , V
IN OUT
and GND will help minimize parasitic electrical
effects along with minimizing the case to ambient thermal
impedance.
ORDERING INFORMATION
Current Limit
[A]
Current Limit
Blanking Time [ms]
Auto Restart
†
Time [ms]
80/160/320
NA
Part Number
FPF2123
On Pin Activity
Active HI
Top Mark
2123
Shipping
0.15 − 1.5
0.15 − 1.5
0.15 − 1.5
5/10/20
5/10/20
Infinite
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
FPF2124
Active HI
2124
FPF2125
NA
Active HI
2425
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D
IntelliMAX is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other coutries.
www.onsemi.com
11
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SOT−23, 5 Lead
CASE 527AH
ISSUE A
DATE 09 JUN 2021
q
q
q
q
q
q1
q2
GENERIC
MARKING DIAGRAM*
XXXM
XXX = Specific Device Code
M
= Date Code
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98AON34320E
SOT−23, 5 LEAD
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
ADDITIONAL INFORMATION
TECHNICAL PUBLICATIONS:
Technical Library: www.onsemi.com/design/resources/technical−documentation
onsemi Website: www.onsemi.com
ONLINE SUPPORT: www.onsemi.com/support
For additional information, please contact your local Sales Representative at
www.onsemi.com/support/sales
相关型号：
©2020 ICPDF网 联系我们和版权申明