FS6370-01G-XTD [ONSEMI]
EEPROM Programmable 3-PLL Clock Generator IC; EEPROM的可编程3 -PLL时钟发生器IC![FS6370-01G-XTD](http://pdffile.icpdf.com/pdf1/p00146/img/icpdf/FS637_811131_icpdf.jpg)
型号: | FS6370-01G-XTD |
厂家: | ![]() |
描述: | EEPROM Programmable 3-PLL Clock Generator IC |
文件: | 总28页 (文件大小:591K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
FS6370
EEPROM Programmable 3-PLL Clock Generator IC
1.0 Features
• Just-in-time customization of clock frequencies via internal non-volatile 128-bit serial EEPROM
• I2C™-bus serial interface
• Three on-chip PLLs with programmable reference and feedback dividers
• Four independently programmable muxes and post dividers
• Programmable power-down of all PLLs and output clock drivers
• Tristate outputs for board testing
• One PLL and two mux/post-divider combinations can be modified via SEL_CD input
• 5 V to 3.3 V operation
• Accepts 5 MHz to 27 MHz crystal resonators
2.0 Description
The FS6370 is a CMOS clock generator IC designed to minimize cost and component count in a variety of electronic systems. Three
EEPROM-programmable phase-locked loops (PLLs) driving four programmable muxes and post dividers provide a high degree of
flexibility.
An internal EEPROM permits just-in-time factory programming of devices for end user requirements.
Figure 1: Pin Configuration
©2008 SCILLC. All rights reserved.
May 2008 – Rev. 3
Publication Order Number:
FS6370/D
FS6370
Figure 2: Block Diagram
Table 1: Pin Descriptions
Pin
1
2
3
4
Type
P
Name
VSS
SEL_CD
PD/SCL
VSS
Description
Ground
DIU
DIU
P
Selects one of two programmed PLL C, Mux C/D and post divider C/D combinations
Power-down input (run-mode) or serial interface clock input (program mode)
Ground
5
AI
XIN
Crystal oscillator feedback
6
7
8
9
10
11
12
13
14
15
16
AO
DIUO
P
XOUT
OE/SDA
VDD
MODE
CLK_D
VSS
CLK_C
CLK_B
VDD
CLK_A
VDD
Crystal oscillator drive
Output enable input (run mode) or serial interface data input/output (program mode)
Power supply (5 V to 3.3 V)
Selects either program mode (low) or run mode (high)
D clock output
Ground
C clock output
B clock output
Power supply (5 V to 3.3 V)
A clock output
DIU
DO
P
DO
DO
P
DO
P
Power supply (5 V to 3.3 V)
Key: AI = Analog Input; AO = Analog Output; DI = Digital Input; DIU = Input with Internal Pull-Up; DID = Input with Internal Pull-Down; DIO = Digital Input/Output; DI-3 = Three-
Level Digital Input, DO = Digital Output; P = Power/Ground; # = Active Low pin
Rev. 3 | Page 2 of 28 | www.onsemi.com
FS6370
3.0 Functional Block Description
3.1 Phase Locked Loops (PLLs)
Each of the three on-chip PLLs is a standard phase- and frequency-locked loop architecture that multiplies a reference frequency to a
desired frequency by a ratio of integers. This frequency multiplication is exact.
As shown in Figure 3, each PLL consists of a reference divider, a phase-frequency detector (PFD), a charge pump, an internal loop
filter, a voltage-controlled oscillator (VCO), and a feedback divider.
During operation, the reference frequency (fREF), generated by the on-board crystal oscillator, is first reduced by the reference divider.
The divider value is often referred to as the modulus, and is denoted as N
the PFD.
R
for the reference divider. The divided reference is fed into
The PFD controls the frequency of the VCO (fVCO) through the charge pump and loop filter. The VCO provides a high-speed, low noise,
continuously variable frequency clock source for the PLL. The output of the VCO is fed back to the PFD through the feedback divider
(the modulus is denoted by N ) to close the loop.
F
Figure 3: PLL Block Diagram
The PFD will drive the VCO up or down in frequency until the divided reference frequency and the divided VCO frequency appearing at
the inputs of the PFD are equal. The input/output relationship between the reference frequency and the VCO frequency is:
3.1.1. Reference Divider
The reference divider is designed for low phase jitter. The divider accepts the output of the reference oscillator and provides a divided-
down frequency to the PFD. The reference divider is an 8-bit divider, and can be programmed for any modulus from 1 to 255 by
programming the equivalent binary value. A divide-by-256 can also be achieved by programming the eight bits to 00h.
3.1.2. Feedback Divider
The feedback divider is based on a dual-modulus pre-scaler technique. The technique allows the same granularity as a fully
programmable feedback divider, while still allowing the programmable portion to operate at low speed. A high-speed pre-divider (also
called a pre-scaler) is placed between the VCO and the programmable feedback divider because of the high speeds at which the VCO
can operate. The dual-modulus technique insures reliable operation at any speed that the VCO can achieve and reduces the overall
power consumption of the divider.
For example, a fixed divide-by-eight pre-scaler could have been used in the feedback divider. Unfortunately, a divide-by-eight would
limit the effective modulus of the entire feedback divider to multiples of eight. This limitation would restrict the ability of the PLL to
Rev. 3 | Page 3 of 28 | www.onsemi.com
FS6370
achieve a desired input-frequency-to-output-frequency ratio without making both the reference and feedback divider values
comparatively large. Generally, very large values are undesirable as they degrade the bandwidth of the PLL, increasing phase jitter and
acquisition time.
To understand the operation of the feedback divider, refer to Figure 4. The M-counter (with a modulus always equal to M) is cascaded
with the dual-modulus pre-scaler. The A-counter controls the modulus of the pres-caler. If the value programmed into the A-counter is
A, the pre-scaler will be set to divide by N+1 for A pre-scaler outputs. Thereafter, the prescaler divides by N until the M-counter output
resets the A-counter, and the cycle begins again. Note that N=8, and A and M are binary numbers.
Figure 4: Feedback Divider
Suppose that the A-counter is programmed to zero. The modulus of the pre-scaler will always be fixed at N; and the entire modulus of
the feedback divider becomes MxN.
Next, suppose that the A-counter is programmed to a one. This causes the pre-scaler to switch to a divide-by-N+1 for its first divide
cycle and then revert to a divide-by-N. In effect, the A-counter absorbs (or "swallows") one extra clock during the entire cycle of the
feedback divider. The overall modulus is now seen to be equal to MxN+1.
This example can be extended to show that the feedback divider modulus is equal to MxN+A, where A<M.
3.1.3. Feedback Divider Programming
For proper operation of the feedback divider, the A-counter must be programmed only for values that are less than or equal to the M-
counter. Therefore, not all divider moduli below 56 are available for use. This is shown in Table 2.
Above a modulus of 56, the feedback divider can be programmed to any value up to 2047.
Table 2: Feedback Divider Modulus Under 56
M-Counter:
A-Counter: FBKDIV[2:0]
FBKDIV[10:3]
000
8
001
9
010
-
011
-
-
27
35
43
51
59
100
-
-
101
-
-
-
-
45
53
61
110
-
-
-
-
-
54
62
111
-
-
-
-
-
-
63
00000001
00000010
00000011
00000100
00000101
00000110
00000111
16
24
32
40
48
56
17
25
33
41
49
57
18
26
34
42
50
58
-
36
44
52
60
Feedback Divider Modulus
3.2 Post Divider Muxes
As shown in Figure 2, a mux in front of each post divider stage can select from any one of the three PLL frequencies or the reference
frequency. The mux selection is controlled by bits in the EEPROM or the control registers.
The input frequency on two of the four multiplexers (muxes C and D in Figure 2) can be altered without reprogramming by a logic-level
input on the SEL_CD pin.
Rev. 3 | Page 4 of 28 | www.onsemi.com
FS6370
3.3 Post Dividers
A post divider performs several useful functions. First, it allows the VCO to be operated in a narrower range of speeds compared to the
variety of output clock speeds that the device is required to generate. Second, it changes the basic PLL equation to:
where NP is the post divider modulus. The extra integer in the denominator permits more flexibility in the programming of the loop for
many applications where frequencies must be achieved exactly.
The modulus on two of the four post dividers (post dividers C and D in Figure 2) can be altered without reprogramming by a logic level
on the SEL_CD pin.
4.0 Device Operation
The FS6370 has two modes of operation:
• Program mode: during which either the EEPROM or the FS6370 control registers can be programmed directly with the desired PLL
settings
• Run mode: where the PLL settings stored the EEPROM are transferred to the FS6370 control registers on power-up, and the device
then operates based on those settings
Note that the EEPROM locations are not physically the same registers used to control the FS6370.
Direct access to either the EEPROM or the FS6370 control registers is achieved in program mode. The EEPROM register contents are
automatically transferred to the FS6370 control registers in normal device operation (run mode).
4.1 MODE Pin
The MODE pin controls the mode of operation. A logic-low places the FS6370 in program mode. A logic-high puts the device in run
mode. A pull-up on this pin defaults the device into run mode.
Reprogramming of either the control registers or the EEPROM is permitted at any time if the MODE pin is a logic-low.
Note, however, that a logic-high state on the MODE pin is latched so that only one transfer of EEPROM data to the FS6370 control
registers can occur. If a second transfer of EEPROM data into the FS6370 is desired, power (VDD) must be removed and reapplied to
the device.
The MODE pin also controls the function of the PD/SCL and OE/SDA pins. In run mode, these two pins function as power-down (PD)
and output enable (OE) controls. In program mode, the pins function as the I C interface for clock (SCL) and data (SDA).
2
4.2 SEL_CD Pin
The SEL_CD pin provides a way to alter the operation of PLL C, muxes C and D, and post dividers C and D without having to
reprogram the device. A logic-low on the SEL_CD pin selects the control bits with a "C1" or "D1" notation, per Table 3. A logic-high on
the SEL_CD pin selects the control bits with "C2" or "D2" notation, per Table 3.
Note that changing between two running frequencies using the SEL_CD pin may produce glitches in the output, especially if the post-
divider(s) is/are altered.
4.3 Oscillator Overdrive
For applications where an external reference clock is provided (and the crystal oscillator is not required), the reference clock should be
connected to XOUT and XIN must be left unconnected (float).
Rev. 3 | Page 5 of 28 | www.onsemi.com
FS6370
For best results, make sure the reference clock signal is as jitter-free as possible, can drive a 40 pF load with fast rise and fall times,
and can swing rail-to-rail.
If the reference clock is not a rail-to-rail signal, the reference must be AC coupled to XOUT through a 0.01 µF or 0.1 µF capacitor. A
minimum 1 V peak-to-peak signal is required to drive the internal differential oscillator buffer.
5.0 Run Mode
If the MODE pin is set to a logic-high, the device enters the run mode. The high state is latched (see MODE pin). The FS6370 then
copies the stored EEPROM data into its control registers and begins normal operation based on that data when the self-load is
complete.
The self-load process takes about 89,000 clocks of the crystal oscillator. During the self-load time, all clock outputs are held low. At a
reference frequency of 27 MHz, the self-load takes about 3.3ms to complete.
If the EEPROM is empty (all zeros), the crystal reference frequency provides the clock for all four outputs.
No external programming access to the FS6370 is possible in run mode. The dual-function PD/SCL and OE/SDA pins become a
power-down (PD) and output enable (OE) control, respectively.
5.1 Power-Down and Output Enable
A logic-high on the PD/SCL pin powers down only those portions of the FS6370 which have their respective power-down control bits
enabled. Note that the PD/SCL pin has an internal pull-up.
When a post divider is powered down, the associated output driver is forced low. When all PLLs and post dividers are powered down
the crystal oscillator is also powered down. The XIN pin is forced low, and the XOUT pin is pulled high.
A logic-low on the OE/SDA pin tristates all output clocks. Note that this pin has an internal pull-up.
6.0 Program Mode
If the MODE pin is logic-low, the device enters the program mode. All internal registers are cleared to zero, delivering the crystal
frequency to all outputs. The device allows programming of either the internal 128-bit EEPROM or the on-chip control registers via I
control over the PD/SCL and OE/SDA pins. The EEPROM and the FS6370 act as two separate parallel devices on the same on-chip
C-bus. Choosing either the EEPROM or the device control registers is done via the I C device address.
2
C
I
2
2
The dual-function PD/SCL and OE/SDA pins become the serial data I/O (SDA) and serial clock input (SCL) for normal I
2
C
communications. Note that power-down and output enable control via the PD/SCL and OE/SDA pins is not available.
6.1 EEPROM Programming
Data must be loaded into the EEPROM in a most-significant-bit (MSB) to least-significant-bit (LSB) order. The register map of the
EEPROM is noted in Table 3.
The device address of the EEPROM is:
A6
A5
A4
A3
A2
A1
A0
1
0
1
0
X
X
X
6.1.1. Write Operation
The EEPROM can only be written to with the random register write procedure (see Section 8.2.2). The procedure consists of the device
address, the register address, a R/W bit, and one byte of data.
Following the STOP condition, the EEPROM initiates its internally timed 4ms write cycle, and commits the data byte to memory. No
acknowledge signals are generated during the EEPROM internal write cycle.
Rev. 3 | Page 6 of 28 | www.onsemi.com
FS6370
If a stop bit is transmitted before the entire write command sequence is complete, then the command is aborted and no data is written
to memory. If more than eight bits are transmitted before the stop bit is sent, then the EEPROM will clear the previously loaded data
byte and will begin loading the data buffer again.
6.1.2. Acknowledge Polling
The EEPROM does not acknowledge while it internally commits data to memory. This feature can be used to increase data throughput
by determining when the internal write cycle is complete.
The process is to initiate the random register write procedure with a START condition, the EEPROM device address, and the write
command bit (R/W=0).
If the EEPROM has completed its internal 4 ms write cycle, the EEPROM will acknowledge on the next clock, and the write command
can continue.
If the EEPROM has not completed the internal 4 ms write cycle, the random register write procedure must be restarted by sending the
START condition, device address and R/W bit. This sequence must be repeated until the EEPROM acknowledges.
6.1.3. Read Operation
The EEPROM supports both the random register read procedure and the sequential register read procedure (both are outlined in
Section 6).
For sequential read operations, the EEPROM has an internal address pointer that increments by one at the end of each read operation.
The pointer directs the EEPROM to transmit the next sequentially addressed data byte, allowing the entire memory contents to be read
in one operation.
6.2 Direct Register Programming
The FS6370 control registers may be directly accessed by simply using the FS6370 device address in the read or write operations. The
operation of the device will follow the register values. The register map of the FS6370 is identical to that of the EEPROM shown in
Table 3.
The FS6370 supports the random read and write procedures, as well as the sequential read and write procedures described in Section
8.
The device address for the FS6370 is:
A6
A5
A4
A3
A2
A1
A0
1
0
1
1
1
0
0
7.0 Cost Reduction Migration Path
The FS6370 is compatible with the programmable register-based FS6377 or a fixed-frequency ROM-based clock generator. Attention
should be paid to the board layout if a migration path to either of these devices is desired.
7.1 Programming Migration Path
If the design can support I
is possible.
2
C programming overhead, a cost reduction from the EEPROM-based FS6370 to the register-based FS6377
Figure 5 shows the five pins that may not be compatible between the various devices if programming of the FS6370 or the FS6377 is
desired.
Rev. 3 | Page 7 of 28 | www.onsemi.com
FS6370
Figure 5: FS6370 to FS6377
7.2 Non-Programming Migration Path
If the design has solidified on a particular EEPROM programming pattern, the EEPROM pattern can be hard-coded into a ROM-based
device. For high-volume requirements, a ROM-based device offers significant cost savings over the FS6370. Contact an ON
Semiconductor sales representative for more detail.
8.0 I
2
C-bus Control Interface
This device is a read/write slave device meeting all Philips I C-bus specifications except a "general call." The bus has to
2
be controlled by a master device that generates the serial clock SCL, controls bus access and generates the START and
STOP conditions while the device works as a slave. Both master and slave can operate as a transmitter or receiver, but
the master device determines which mode is activated. A device that sends data onto the bus is defined as the
transmitter, and a device receiving data as the receiver.
I
V
2
C-bus logic levels noted herein are based on a percentage of the power supply (VDD). A logic-one corresponds to a nominal voltage of
DD, while a logic-low corresponds to ground (VSS).
8.1 Bus Conditions
Data transfer on the bus can only be initiated when the bus is not busy. During the data transfer, the data line (SDA) must remain stable
whenever the clock line (SCL) is high. Changes in the data line while the clock line is high will be interpreted by the device as a START
or STOP condition. The following bus conditions are defined by the I C-bus protocol.
2
8.1.1. Not Busy
Both the data (SDA) and clock (SCL) lines remain high to indicate the bus is not busy.
8.1.2. START Data Transfer
A high to low transition of the SDA line while the SCL input is high indicates a START condition. All commands to the device must be
preceded by a START condition.
Rev. 3 | Page 8 of 28 | www.onsemi.com
FS6370
8.1.3. STOP Data Transfer
A low to high transition of the SDA line while SCL is held high indicates a STOP condition. All commands to the device must be
followed by a STOP condition.
8.1.4. Data Valid
The state of the SDA line represents valid data if the SDA line is stable for the duration of the high period of the SCL line after a START
condition occurs. The data on the SDA line must be changed only during the low period of the SCL signal. There is one clock pulse per
data bit.
Each data transfer is initiated by a START condition and terminated with a STOP condition. The number of data bytes transferred
between START and STOP conditions is determined by the master device, and can continue indefinitely. However, data that is
overwritten to the device after the first 16 bytes will overflow into the first register, then the second, and so on, in a first-in, first-
overwritten fashion.
8.1.5. Acknowledge
When addressed, the receiving device is required to generate an acknowledge after each byte is received. The master device must
generate an extra clock pulse to coincide with the acknowledge bit. The acknowledging device must pull the SDA line low during the
high period of the master acknowledge clock pulse. Setup and hold times must be taken into account.
The master must signal an end of data to the slave by not generating an acknowledge bit on the last byte that has been read (clocked)
out of the slave. In this case, the slave must leave the SDA line high to enable the master to generate a STOP condition.
8.2 I
2
C-bus Operation
All programmable registers can be accessed randomly or sequentially via this bi-directional two wire digital interface. The device
accepts the following I C-bus commands.
2
8.2.1. Device Address
After generating a START condition, the bus master broadcasts a seven-bit device address followed by a R/W bit.
The device address of the FS6370 is:
A6
A5
A4
A3
A2
A1
A0
1
0
1
1
1
0
0
Any one of eight possible addresses are available for the EEPROM. The least significant three bits are don’t care’s.
A6
A5
A4
A3
A2
A1
A0
1
0
1
0
X
X
X
8.2.2. Random Register Write Procedure
Random write operations allow the master to directly write to any register. To initiate a write procedure, the R/W bit that is transmitted
after the seven-bit device address is a logic-low. This indicates to the addressed slave device that a register address will follow after the
slave device acknowledges its device address. The register address is written into the slave's address pointer. Following an
acknowledge by the slave, the master is allowed to write eight bits of data into the addressed register. A final acknowledge is returned
by the device, and the master generates a STOP condition.
If either a STOP or a repeated START condition occurs during a register write, the data that has been transferred is ignored.
8.2.3. Random Register Read Procedure
Random read operations allow the master to directly read from any register. To perform a read procedure, the R/W bit that is
transmitted after the seven-bit address is a logic-low, as in the register write procedure. This indicates to the addressed slave device
that a register address will follow after the slave device acknowledges its device address. The register address is then written into the
slave's address pointer.
Rev. 3 | Page 9 of 28 | www.onsemi.com
FS6370
Following an acknowledge by the slave, the master generates a repeated START condition. The repeated START terminates the write
procedure, but not until after the slave's address pointer is set. The slave address is then resent, with the R/W bit set this time to a
logic-high, indicating to the slave that data will be read. The slave will acknowledge the device address, and then transmits the eight-bit
word. The master does not acknowledge the transfer but does generate a STOP condition.
8.2.4. Sequential Register Write Procedure
Sequential write operations allow the master to write to each register in order. The register pointer is automatically incremented after
each write. This procedure is more efficient than the random register write if several registers must be written.
To initiate a write procedure, the R/W bit that is transmitted after the seven-bit device address is a logic-low. This indicates to the
addressed slave device that a register address will follow after the slave device acknowledges its device address. The register address
is written into the slave's address pointer. Following an acknowledge by the slave, the master is allowed to write up to 16 bytes of data
into the addressed register before the register address pointer overflows back to the beginning address. An acknowledge by the device
between each byte of data must occur before the next data byte is sent.
Registers are updated every time the device sends an acknowledge to the host. The register update does not wait for the STOP
condition to occur. Registers are therefore updated at different times during a sequential register write.
8.2.5. Sequential Register Read Procedure
Sequential read operations allow the master to read from each register in order. The register pointer is automatically incremented by
one after each read. This procedure is more efficient than the random register read if several registers must be read.
To perform a read procedure, the R/W bit that is transmitted after the seven-bit address is a logic-low, as in the register write procedure.
This indicates to the addressed slave device that a register address will follow after the slave device acknowledges its device address.
The register address is then written into the slave's address pointer.
Following an acknowledge by the slave, the master generates a repeated START condition. The repeated START terminates the write
procedure, but not until after the slave's address pointer is set. The slave address is then resent, with the R/W bit set this time to a
logic-high, indicating to the slave that data will be read. The slave will acknowledge the device address, and then transmits all 16 bytes
of data starting with the initial addressed register. The register address pointer will overflow if the initial register address is larger than
zero. After the last byte of data, the master does not acknowledge the transfer but does generate a STOP condition.
Rev. 3 | Page 10 of 28 | www.onsemi.com
FS6370
Figure 6: Random Register Write Procedure
Figure 7: Random Register Read Procedure
Figure 8: Sequential Register Write Procedure
Figure 9: Sequential Register Read Procedure
Rev. 3 | Page 11 of 28 | www.onsemi.com
FS6370
9.0 Programming Information
Table 3: Register Map (Note: All register bits are cleared to zero on power-up)
Address
Byte 15
Bit 7
MUX_D2[1:0]
(selected via SEL_CD = 1)
POST_D2[3:0]
Bit 6
Bit 5
MUX_C2[1:0]
(selected via SEL_CD = 1)
Bit 4
Bit 3
PDPOST_D
Bit 2
PDPOST_C
Bit 1
PDPOST_B
Bit 0
PDPOST_A
Byte 14
Byte 13
POST_C2[3:0]
(selected via SEL_CD = 1)
(selected via SEL_CD = 1)
POST_D1[3:0]
POST_C1[3:0]
(selected via SEL_CD = 0)
POST_B[3:0]
(selected via SEL_CD = 0)
POST_A[3:0]
Byte 12
Byte 11
MUX_D1[1:0]
(selected via SEL_CD = 0)
Reserved (0)
LFTC_C2
(SEL_CD=1)
CP_C2
(SEL_CD=1)
FBKDIV_C2[10:8] M-Counter
(selected via SEL_CD pin = 1)
FBKDIV_C2[2:0] A-Counter
(selected via SEL_CD pin = 1)
Byte 10
Byte 9
Byte 8
Byte 7
Byte 6
FBKDIV_C2[7:3] M-Counter
(selected via SEL_CD pin = 1)
REFDIV_C2[7:0]
(selected via SEL_CD pin = 1)
LFTC_C1
MUX_C1[1:0]
PDPLL_C
CP_C1
(SEL_CD=0)
FBKDIV_C1[10:8] M-Counter
(selected via SEL_CD = 0)
FBKDIV_C1[2:0] A-Counter
(selected via SEL_CD = 1)
(selected via SEL_CD = 0)
(SEL_CD=0)
FBKDIV_C1[7:3] M-Counter
(selected via SEL_CD = 0
REFDIV_C1[7:0]
(selected via SEL_CD = 0)
LFTC_B CP_B
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0
MUX_B[1:0]
MUX_A[1:0]
PDPLL_B
FBKDIV_B[7:3] M-Counter
FBKDIV_B[10:8] M-Counter
FBKDIV_B[2:0] A-Counter
REFDIV_B[7:0]
LFTC_A CP_A
PDPLL_A
FBKDIV_A[10:8] M-Counter
FBKDIV_A[2:0] A-Counter
FBKDIV_A[7:3] M-Counter
REFDIV_A[7:0]
9.1 Control Bit Assignments
If any PLL control bit is altered during device operation, including those bits controlling the reference and feedback dividers, the output
frequency will slew smoothly (in a glitch-free manner) to the new frequency. The slew rate is related to the programmed loop filter time
constant.
However, any programming changes to any mux or post divider control bits will cause a glitch on an operating clock output.
9.1.1. Power-Down
All power-down functions are controlled by enable bits. That is, the bits select which portions of the FS6370 to power-down when the
PD input is asserted. If the power-down bit contains a one, the related circuit will shut down if the PD pin is high (run mode only). When
the PD pin is low, power is enabled to all circuits.
If the power-down bit contains a zero, the related circuit will continue to function regardless of the PD pin state.
Rev. 3 | Page 12 of 28 | www.onsemi.com
FS6370
Table 4: Power-Down Bits
Name
Description
Power-Down PLL A
Bit = 0
PDPLL_A
(Bit 21)
Power on
Power off
Bit = 1
Power-Down PLL B
Bit = 0
Bit = 1
PDPLL_B
(Bit 45)
Power on
Power off
Power-Doan PLL C
Bit = 0
Bit = 1
PDPLL_C
(Bit 69)
Power on
Power off
Reserved (0)
(Bit 69)
Power-Down POST Divider A
PDPOST_A
(Bit 120)
Bit = 0
Bit = 1
Power on
Power off
Power-Down POST Divider B
PDPOST_B
(Bit 121)
Bit = 0
Bit = 1
Power on
Power off
Power-Down POST Divider C
PDPOSTC
(Bit 122)
Bit = 0
Bit = 1
Power on
Power off
Power-Down POST Divider D
PDPOSTD
(Bit 123)
Bit = 0
Bit = 1
Power on
Power off
Table 5: Divider Control Bits
Name
Description
REFDIV_A[7:0]
(Bits 7-0)
Reference Divider A (N
R
R
)
)
REFDIV_B[7:0]
(Bits 31-24)
REFDIV_C1[7:0]
(Bits 55-48)
REFDIV_C2[7:0]
(Bits 79-72)
Reference Divider B (N
Reference Divider C1 (N
selected when the SEL-CD pin = 0
Reference Divider C2 (N
selected when the SEL-CD pin = 1
R
)
R
)
Feedback Divider A (N
FBKDIV_A[2:0]
FBKDIV_A[10:3]
F
)
FBKDIV_A[10:0]
(Bits 18-8)
A-Counter value
M-Counter value
Feedback Divider B (N
FBKDIV_B[2:0]
FBKDIV_B[10:3]
F
)
FBKDIV_B[10:0]
(Bits 42-32)
A-Counter value
M-Counter value
Feedback Divider C1 (N )
F
selected when the SEL-CD pin = 0
FBKDIV_C1[10:0]
(Bits 66-56)
FBKDIV_C1[2:0]
FBKDIV_C1[10:3]
A-Counter value
M-Counter value
Feedback Divider C2 (N )
F
selected when the SEL-CD pin = 1
FBKDIV_C2[10:0]
(Bits 90-80)
FBKDIV_C2[2:0]
FBKDIV_C2[10:3]
A-Counter value
M-Counter value
Rev. 3 | Page 13 of 28 | www.onsemi.com
FS6370
Table 6: Post Divider Control Bits
Name
Description
POST_A[3:0]
(Bits 99-96)
POST divider A (see Table 7)
POST_B[3:0]
(Bits 103-100)
POST_C1[3:0]
(Bits 107-104)
POST_C2[3:0]
(Bits 115-112)
POST_D1[3:0]
(Bits 111-108)
POST_D2[3:0]
(Bits 119-116)
POST divider B (see Table 7)
POST divider C1 (see Table 7)
selected when the SEL_CD pin = 0
POST divider C2 (see Table 7)
selected when the SEL_CD pin = 1
POST divider D1 (see Table 7)
selected when the SEL_CD pin = 0
POST divider D2 (see Table 7)
selected when the SEL_CD pin = 1
Table 7: Post Divider Modulus
Bit [3]
Bit [2]
Bit [1]
Bit [0]
Divide By
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
2
3
4
5
6
8
9
10
12
15
16
18
20
25
50
Rev. 3 | Page 14 of 28 | www.onsemi.com
FS6370
Table 8: PLL Tuning Bits
Name
Description
Loop Filter Time Constant A
Bit = 0
LFTC_A
(Bit 20)
Short time constant: 7 µs
Bit = 1
Long time constant: 20 µs
Loop Filter Time Constant B
LFTC_B
(Bit 44)
Bit = 0
Short time constant: 7 µs
Bit = 1
Long time constant: 20 µs
Loop Filter Time Constant C1 - Selected when the SEL_CD pin = 0
LFTC_C1
(Bit 68)
Bit = 0
Short time constant: 7 µs
Long time constant: 20 µs
Bit = 1
Loop Filter Time Constant C2 - Selected when the SEL_CD pin = 1
LFTC_C2
(Bit 92)
Bit = 0
Short time constant: 7 µs
Bit = 1
Long time constant: 20 µs
Charge Pump A
Bit = 0
Bit = 1
CP_A
(Bit 19)
Current = 2 µA
Current = 10 µA
Charge Pump B
Bit = 0
Bit = 1
CP_B
(Bit 43)
Current = 2 µA
Current = 10 µA
Charge Pump C1 - Selected when the SEL_CD pin = 0
CP_C1
(Bit 67)
Bit = 0
Bit = 1
Current = 2 µA
Current = 10 µA
Charge Pump C2 - Selected when the SEL_CD pin = 1
CP_C2
(Bit 91)
Bit = 0
Bit = 1
Current = 2 µA
Current = 10 µA
Rev. 3 | Page 15 of 28 | www.onsemi.com
FS6370
Table 9: MUX Select Bits
Name
Description
MUX A Frequency Select
Bit 23
Bit 22
0
0
1
1
0
1
0
1
Reference frequency
PLL A frequency
PLL B frequency
PLL C frequency
MUX_A[1:0]
(Bits 23-22)
MUX B Frequency Select
Bit 47
Bit 46
0
0
1
1
0
1
0
1
Reference frequency
PLL A frequency
PLL B frequency
PLL C frequency
MUX_B[1:0]
(Bits 47-46)
MUX C1 Frequency Select – Selected when the SEL_CD pin = 0
Bit 71
Bit 70
Reference frequency
PLL A frequency
PLL B frequency
PLL C frequency
0
0
1
1
0
1
0
1
MUX_C1[1:0]
(Bits 71-70)
MUX C2 Frequency Select – Selected when the SEL_CD pin = 1
Bit 125
Bit 124
0
0
1
1
0
1
0
1
Reference frequency
PLL A frequency
PLL B frequency
PLL C frequency
MUX_C2[1:0]
(Bits 125-124)
MUX D1 Frequency Select – Selected when the SEL_CD pin = 0
Bit 95
Bit 94
0
0
1
1
0
1
0
1
Reference frequency
PLL A frequency
PLL B frequency
PLL C frequency
MUX_D1[1:0]
(Bits 95-94)
MUX D2 Frequency Select – Selected when the SEL_CD pin = 1
Bit 127
Bit 126
0
0
1
1
0
1
0
1
Reference frequency
PLL A frequency
PLL B frequency
PLL C frequency
MUX_D2[1:0]
(Bits 127-126)
Rev. 3 | Page 16 of 28 | www.onsemi.com
FS6370
10.0 Electrical Specifications
Table 10: Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Units
Supply Voltage, dc (VSS = ground)
VDD
VSS-0.5
7
V
Input Voltage, dc
VI
VO
IIK
VSS-0.5
VSS-0.5
-50
VDD+0.5
VDD+0.5
50
V
V
Output Voltage, dc
Input Clamp Current, dc (VI < 0 or VI > VDD
)
mA
mA
°C
°C
°C
°C
kV
Output Clamp Current, dc (VI < 0 or VI > VDD
)
IOK
TS
TA
TJ
-50
50
Storage Temperature Range (non-condensing)
Ambient Temperature Range, Under Bias
Junction Temperature
-65
150
-55
125
150
Re-Flow Solder Profile
260
Input Static Discharge Voltage Protection (MIL-STD 883E, Method 3015.7)
2
Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. These conditions represent a stress rating only, and functional operation of the
device at these or any other conditions above the operational limits noted in this specification is not implied. Exposure to maximum rating conditions for extended conditions may affect
device performance, functionality and reliability.
CAUTION: ELECTROSTATIC SENSITIVE DEVICE
Permanent damage resulting in a loss of functionality or performance may occur if this device is subjected to a high-energy
electrostatic discharge.
Table 11: Operating Conditions
Parameter
Symbol
Conditions/Descriptions
5 V ± 10%
Min.
4.5
3
Typ.
5
Max.
5.5
3.6
70
Units
Supply Voltage
VDD
V
3.3 V ± 10%
3.3
Ambient Operating Temperature Range
Crystal Resonator Frequency
TA
fXIN
CXL
0
°C
MHz
pF
5
27
Crystal Resonator Load Capacitance
Serial Data Transfer Rate
Parallel resonant, AT cut
Standard mode
18
10
100
15
kb/s
pF
Output Driver Load Capacitance
CL
Rev. 3 | Page 17 of 28 | www.onsemi.com
FS6370
Table 12: DC Electrical Specifications
Parameter
Symbol
Conditions/Description
Min.
Typ.
Max.
Units
Overall
Supply Current, Dynamic
VDD = 5.5V, fCLK = 50MHz ; CL = 15pF
See Figure 11 for more information
IDD
43
2
mA
mA
Additional operating current demand,
EEPROM program mode, VDD = 5.5 V
Supply Current, Write
Supply Current, Read
IDD(write)
Additional operating current demand,
EEPROM program mode, VDD = 5.5 V
IDD(read)
IDDL
1
mA
mA
Supply Current, Static
VDD = 5.5V, powered down via PD pin
0.3
Dual Function I/O (P
VDD = 5.5V
3.85
2.52
VDD+0.3
VDD+0.3
VDD+0.3
VDD+0.3
VDD+0.3
VDD+0.3
1.65
Run mode (PD, OE)
VDD = 3.6V
VDD = 5.5V
3.85
Register program mode
(SDA, SCL)
High-Level Input Voltage
Low-Level Input Voltage
Hysteresis Voltage
VIH
V
V
V
V
DD = 3.6V
VDD = 5.5V
DD = 3.6V
2.52
3.85
EEPROM prodgram mode
(SDA, SCL)
V
2.52
VDD = 5.5V
VDD = 3.6V
VDD = 5.5V
VDD = 3.6V
VDD = 5.5V
VDD = 3.6V
VDD = 5.5V
VDD = 3.6V
VDD = 5.5V
VSS-0.3
VSS-0.3
VSS-0.3
VSS-0.3
VSS-0.3
VSS-0.3
Run mode (PD, OE)
1.08
1.65
Register program mode
(SDA, SCL)
VIL
1.08
1.65
EEPROM prodgram mode
(SDA, SCL)
1.08
2.20
1.44
2.20
1.44
0.275
0.18
Run mode (PD, OE)
Register program mode
(SDA, SCL)
Vhys
V
DD = 3.6V
VDD = 5.5V
DD = 3.6V
Register program mode
(SDA, SCL)
V
Run/register program mode
EEPROM program mode
VIL = 0V
-1
-1
1
1
High-Level Input Current
IIH
IIL
μA
µA
Low-Level Input Current (pull-up)
Low-Level Output Sink Current (SDA)
-20
-36
26
-80
Run/register program mode, VOL = 0.4V
EEPROM program mode, VOL = 0.4V
IOL
mA
3.0
Mode and Frequency Select Inputs (MODE, SEL_CD)
VDD = 5.5 V
VDD = 3.6 V
VDD = 5.5 V
VDD = 3.6 V
2.4
2.0
VDD+0.3
VDD+0.3
0.8
High-Level Input Voltage
VIH
VIL
V
V
VSS-0.3
VSS-0.3
-1
Low-Level Input Voltage
High-Level Input Current
0.8
IIH
IIL
1
μA
μA
Low-Level Input Current (pull-up)
-20
-36
-80
Parameter
Symbol
Conditions/Description
Min.
Type.
Max.
Units
Rev. 3 | Page 18 of 28 | www.onsemi.com
FS6370
Table 12: DC Electrical Specifications (Continued)
Crystal Oscillator Feedback (XIN)
VDD = 5.5 V
2.9
1.7
54
Threshold Bias Voltage
High-Level Input Current
VTH
V
VDD = 3.6 V
VDD = 5.5 V
mA
mA
µA
IIH
VDD = 5.5 V, oscillator powered down
5
15
Low-Level Input Current
IIL
-25
-54
18
-75
As seen by an external crystal connected
to XIN and XOUT
Crystal Loading Capacitance *
CL(xtal)
pF
pF
As seen by an external clock driver on
XOUT; XIN unconnected
Input Loading Capacitance *
CL(XIN)
36
Crystal Oscillator Output (XOUT)
High-Level Output Source Current
Low-Level Output Sink Current
IOH
IOL
VDD = V(XIN) = 5.5 V, VO = 0 V
VDD = 5.5 V, V(XIN = VO = 5.5 V
10
21
30
mA
mA
-10
-21
-30
Clock Outputs (CLK_A, CLK_B, CLK_C, CLK_D)
High-Level Output Source Current
Low-Level Output Sink Current
IOH
VO = 2.4 V
-125
23
mA
mA
IOL
zOH
zOL
IZ
VO = 0.4 V
VO = 0.5VDD; output driving high
VO = 0.5VDD; output driving low
29
Output Impedance
Ω
27
Tristate Output Current
-10
10
µA
mA
mA
VDD = 5.5 V , VO = 0 V; shorted for 30s,
max
Short Circuit Source Current *
Short Circuit Sink Current *
ISCH
ISCL
-150
123
VDD = VO = 5.5 V; shorted for 30s, max.
Low Drive Current (mA)
High Drive Current (mA)
Voltage
(V)
Voltage
(V)
Min.
0
Typ.
0
Max.
0
Min.
-87
-85
-83
-80
-74
-65
-61
-53
-48
-39
-32
-21
-13
0
Typ.
-112
-110
-108
-104
-97
-88
-84
-77
-71
-62
-55
-44
-36
-24
-15
0
Max.
-150
-147
-144
-139
-131
-121
-116
-108
-102
-92
0
0
0.2
0.5
0.7
1
9
11
25
34
46
52
61
66
73
77
81
83
85
87
88
89
91
12
0.5
1
22
29
39
44
51
55
60
62
65
65
66
67
68
69
29
40
1.5
2
55
1.2
1.5
1.7
2
64
2.5
2.7
3
76
83
92
3.2
3.5
3.7
4
2.2
2.5
2.7
3
97
104
108
112
117
119
120
121
123
-85
-74
4.2
4.5
4.7
5
-65
3.5
4
-52
-43
4.5
5
-28
5.2
5.5
-11
The data in this table represents nominal characterization data only.
5.5
0
Figure 10: CLK_A, CLK_B, CLK_C, CLK_D Clock Output
Rev. 3 | Page 19 of 28 | www.onsemi.com
FS6370
Figure 11: Dynamic Current vs. Output Frequency
Rev. 3 | Page 20 of 28 | www.onsemi.com
FS6370
Table 13: AC Timing Specifications
Clock
(MHz)
Parameter
Symbol
Conditions/Description
Min.
Typ.
Max.
Units
Overall
EEPROM Write Cycle Time
Twc
fO
4
ms
VDD = 5.5 V
0.8
0.8
40
150
100
230
170
Output Frequency *
MHz
V
DD = 3.6 V
VDD = 5.5 V
VDD = 3.6 V
VCO Frequency *
VCO Gain *
fVCO
MHz
MHz/V
μs
40
AVCO
400
7
LFTC bit = 0
Loop Filter Time Constant *
LFTC bit = 1
20
VO = 0.5 V to 4.5 V; CL = 15pF
VO = 0.3 V to 3.0 V; CL = 15pF
VO = 4.5 V to 0.5 V; CL = 15pF
VO = 3.0 V to 0.3 V; CL = 15pF
2.0
2.1
1.8
1.9
Rise Time *
Fall Time *
tr
tf
ns
ns
Tristate Enable Delay *
Tristate Disable Delay *
tPZL, tPZH
tPZL, tPZH
1
1
8
8
ns
ns
Output active from power-up, RUN mode via PD pin
After last register is written, register program mode
100
μs
Clock Stabilization Time *
tSTB
1
ms
Divider Modulus
Feedback Divider
Reference Divider
Post Divider
NF
NR
NP
See also Error! Reference source not found.
See also Error! Reference source not found.
8
1
1
2047
255
50
Clock Output (PLL A clock via CLK_A pin)
Ratio of pulse width (as measured from rising edge to next falling
edge at 2.5V) to one clock period
Duty Cycle *
100
100
45
55
%
On rising edges 500µs apart at 2.5V relative to an ideal clock,
CL=15pF, fXIN=14.318MHz, NF=220, NR=63, NPX=50, no other
PLLs active
On rising edges 500µs apart at 2.5V relative to an ideal clock,
CL=15pF, =14.318MHz, NF=220, NR=63, NPX=50, all other
PLLs active (B=60MHz, C=40MHz, D=14.318MHz)
From rising edge to the next rising edge at 2.5V, CL=15pF,
fXIN=14.318MHz, NF=220, NR=63, NPX=50, no other PLLs
active
45
Tj(LT)
ps
Jitter, Long Term (σy(τ)) *
50
100
50
165
110
390
Jitter, Period (peak-peak)
*
ps
tj(ΔP)
From rising edge to the next rising edge at 2.5V, CL=15pF,
fXIN=14.318MHz, NF=220, NR=63, NPX=50, all other PLLs
active (B=60MHz, C=40MHz, D=14.318MHz)
Clock Output (PLL B clock via CLK_B pin)
Ratio of pulse width (as measured from rising edge to next falling
edge at 2.5V) to one clock period
Duty Cycle *
100
100
45
55
%
On rising edges 500µs apart at 2.5V relative to an ideal clock,
CL=15pF, fXIN=14.318MHz, NF=220, NR=63, NPX=50, no other
PLLs active
On rising edges 500µs apart at 2.5V relative to an ideal clock,
CL=15pF, =14.318MHz, NF=220, NR=63, NPX=50, all other
PLLs active (A=50MHz, C=40MHz, D=14.318MHz)
From rising edge to the next rising edge at 2.5V, CL=15pF,
fXIN=14.318MHz, NF=220, NR=63, NPX=50, no other PLLs
active
45
75
Tj(LT)
ps
Jitter, Long Term (σy(τ)) *
60
100
60
120
400
Jitter, Period (peak-peak)
*
ps
tj(ΔP)
From rising edge to the next rising edge at 2.5V, CL=15pF,
fXIN=14.318MHz, NF=220, NR=63, NPX=50, all other PLLs
active (A=50MHz, C=40MHz, D=14.318MHz)
Rev. 3 | Page 21 of 28 | www.onsemi.com
FS6370
Table 13: AC Timing Specifications (Continued)
Clock
(MHz)
Parameter
Symbol
Conditions/Description
Min.
Typ.
Max.
Units
Clock Output (PLL C clock via CLK_C pin)
Ratio of pulse width (as measured from rising edge to next falling
edge at 2.5V) to one clock period
Duty Cycle*
100
100
45
55
%
On rising edges 500µs apart at 2.5V relative to an ideal clock,
C
L
=15pF, fXIN=14.318MHz, N
active
On rising edges 500µs apart at 2.5V relative to an ideal clock,
=15pF, fXIN=14.318MHz, N =220, N =63, NPx=50, all other PLLs
F
=220, N =63, NPx=50, no other PLLs
R
45
Tj(LT)
ps
Jitter, Long Term (σy(τ))*
CL
F
R
40
100
40
105
120
440
active (A=50MHz, B=60MHz, D=14.318MHz)
From rising edge to the next rising edge at 2.5V, C =15pF,
L
f
XIN=14.318MHz, N
From rising edge to the next rising edge at 2.5V, C
XIN=14.318MHz, N =220, N =63, NPx=50, all other PLLs active
(A=50MHz, B=60MHz, D=14.318MHz)
F
=220, N
R
=63, NPx=50, no other PLLs active
Jitter, Period (peak-peak)*
L
=15pF,
ps
tj(ΔP)
f
F
R
Clock Output (Crystal Oscillator via CLK_D pin)
Ratio of pulse width (as measured from rising edge to next falling
edge at 2.5V) to one clock period
Duty Cycle*
14.318
14.318
45
55
%
On rising edges 500µs apart at 2.5V relative to an ideal clock,
C
L
=15pF, fXIN=14.318MHz, N
active
From rising edge to the next rising edge at 2.5V, C
F
=220, N =63, NPx=50, no other PLLs
R
20
Tj(LT)
ps
Jitter, Long Term (σy(τ))*
L
=15pF,
f
XIN=14.318MHz, all other PLLs active (A=50MHz, B=60MHz,
14.318
14.318
14.318
40
90
C=40MHz)
From rising edge to the next rising edge at 2.5V, C
f
From rising edge to the next rising edge at 2.5V, C
L
=15pF,
=15pF,
XIN=14.318MHz, no other PLLs active
Jitter, Period (peak-peak)*
L
ps
tj(ΔP)
f
XIN=14.318MHz, all other PLLs active (A=50MHz, B=60MHz,
C=40MHz)
Unless otherwise stated, VDD = 5.0V ± 10%, no load on any output, and ambient temperature range T
450
A
= 0°C to 70°C. Parameters denoted with an asterisk ( * ) represent nominal characterization data and
are not currently production tested to any specific limits. Min. and Max. characterization data are ± 3s from typical.
Table 14: Serial Interface Timing Specifications
Parameter
Symbol
fSCL
Conditions/Description
Min.
0
Max.
Units
kHz
μs
Clock frequency
SCL
100
Bus free time between STOP and START
Set up time, START (repeated)
Hold time, START
tBUF
4.7
4.7
4.0
250
0
tsu:STA
thd:STA
tsu:DAT
thd:DAT
μs
μs
Set up time, data input
Hold time, data input
SDA
SDA
ns
μs
Minimum delay to bridge undefined region of the falling
edge of SCL to avoid unintended START or STOP
Output data valid from clock
tAA
3.5
μs
Rise time, data and clock
Fall time, data and clock
High time, clock
tR
tF
SDA, SCL
SDA, SCL
SCL
1000
300
ns
ns
μs
μs
μs
tHI
4.0
4.7
4.0
Low time, clock
tLO
SCL
Set up time, STOP
tsu:STO
Rev. 3 | Page 22 of 28 | www.onsemi.com
FS6370
Figure 12: Bus Timing Data
Figure 13: Data Transfer Sequence
Rev. 3 | Page 23 of 28 | www.onsemi.com
FS6370
11.0 Package Information for Both ‘Green’ and ‘Non-Green’
Table 15: 16-pin SOIC (0.150") Package Dimensions
Dimension
Inches
Millimeters
Min.
Max.
Min.
Max.
A
A1
A2
B
0.061
0.004
0.055
0.013
0.068
0.0098
0.061
0.019
1.55
0.102
1.40
1.73
0.249
1.55
0.33
0.49
C
D
E
0.0075 0.0098
0.191
9.80
0.249
9.98
0.386
0.150
0.393
0.157
3.81
3.99
e
0.050 BSC
1.27 BSC
H
h
0.230
0.010
0.016
0.244
0.016
0.035
5.84
0.25
0.41
6.20
0.41
0.89
8°
L
Θ
0°
8°
0°
Table 16: 16-pin SOIC (0.150") Package Characteristics
Parameter
Symbol
Conditions/Description
Typ.
Units
Thermal Impedance, Junction to Free-Air
16-pin 0.150” SOIC
Air flow = 0 m/s
109
°C/W
ΘJA
Corner lead
4.0
3.0
0.4
0.5
Lead Inductance, Self
L11
nH
Center lead
Lead Inductance, Mutual
Lead Capacitance, Bulk
L12
Any lead to any adjacent lead
Any lead to VSS
nH
pF
C11
12.0 Ordering Information
Temperature Range
Part Number
Package
Shipping Configuration
16-pin (0.150”) SOIC
(green, ROHS or lead
free packaging)
FS6370-01G-XTD
Tube/Tray
0°C to 70°C (Commercial)
16-pin (0.150”) SOIC
(green, ROHS or lead
free packaging)
FS6370-01G-XTP
Tape & Reel
0°C to 70°C (Commercial)
Rev. 3 | Page 24 of 28 | www.onsemi.com
FS6370
13.0 Demonstration Software
Windows 3.1x/95/98-based software is available from ON Semiconductor that illustrates the capabilities of the FS6370. The software
can operate under Windows NT.
Contact your local sales representative for more information.
13.1 Software Requirements
• PC running MS Windows 3.1x or 95/98. Software also runs on Windows NT in a calculation mode only.
• 1.8MB available space on hard drive C.
13.2 Software Installation Instructions
At the appropriate disk drive prompt (A:\) unzip the compressed demo files to a directory of your choice. Run setup.exe to install the
software.
13.3 Demo Program Operation
Launch the fs6370.exe program. Note that the parallel port can not be accessed if your machine is running Windows NT. A warning
message will appear stating: "This version of the demo program cannot communicate with the FS6370 hardware when running on a
Windows NT operating system. Do you want to continue anyway, using just the calculation features of this program?" Clicking OK starts
the program for calculation only.
The FS6370 demonstration hardware is no longer available nor supported.
The opening screen is shown in Figure 14 .
Figure 14: Opening Screen
Rev. 3 | Page 25 of 28 | www.onsemi.com
FS6370
13.3.1. Example Programming
Type a value for the crystal resonator frequency in MHz in the reference crystal box. This frequency provides the basis for all of the PLL
calculations that follow.
Next, click on the PLL A box. A pop-up screen similar to Figure 15 should appear. Type in a desired output clock frequency in MHz, set
the operating voltage (3.3 V or 5 V), and the desired maximum output frequency error. Pressing calculate solutions generates several
possible divider and VCO-speed combinations.
Figure 15: PLL Screen
For a 100 MHz output, the VCO should ideally operate at a higher frequency, and the reference and feedback dividers should be as
small as possible. In this example, highlight solution #7. Notice the VCO operates at 200MHz with a post divider of 2 to obtain an
optimal 50 percent duty cycle.
Now choose which mux and post divider to use (that is, choose an output pin for the 100 MHz output). Selecting A places the PostDiv
value in solution #7 into post divider A and switches mux A to take the output of PLL A.
The PLL screen should disappear, and now the value in the PLL A box is the new VCO frequency chosen in solution #7. Note that mux
A has been switched to PLL A and the post divider A has the chosen 100MHz output displayed.
Repeat the steps for PLL B.
PLL C supports two different output frequencies depending on the setting of the SEL_CD pin. Both mux C and mux D are also affected
by the logic level on the SEL_CD pin, as are the post dividers C and D (see Section 4.2 for more detail).
Rev. 3 | Page 26 of 28 | www.onsemi.com
FS6370
Figure 16: Post Divider Menu
Click on PLL C1 to open the PLL screen. Set a desired frequency, however, now choose the post divider B as the output divider. Notice
the post divider box has split in two (as shown in Figure 16). The post divider B box now shows that the divider is dependent on the
setting of the SEL_CD pin for as long as mux B is the PLL C output.
Clicking on post divider A reveals a pull-down menu provided to permit adjustment of the post divider value independently of the PLL
screen. A typical menu is shown in Figure 16. The range of possible post divider values is also given in Table 7.
The EEPROM settings are shown to the left in the screen shown in Figure 14. Clicking on a register location displays a screen shown in
Figure 17. Individual bits can be poked, or the entire register value can be changed.
Figure 17: Register Screen
Rev. 3 | Page 27 of 28 | www.onsemi.com
FS6370
14.0 Revision History
Revision Date
Modification
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any
products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising
out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical”
parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the
rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to
support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or
use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action
Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800-282-9855
Toll Free USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81-3-5773-3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada
Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
Rev. 3 | Page 28 of 28 | www.onsemi.com
相关型号:
©2020 ICPDF网 联系我们和版权申明