HGTG20N60B3 [ONSEMI]
600V,PT IGBT;型号: | HGTG20N60B3 |
厂家: | ONSEMI |
描述: | 600V,PT IGBT 局域网 电动机控制 栅 瞄准线 双极性晶体管 开关 |
文件: | 总8页 (文件大小:422K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UFS Series N-Channel IGBTs
40 A, 600 V
HGTG20N60B3
The HGTG20N60B3 is a Generation III MOS gated high voltage
switching devices combining the best features of MOSFETs and
bipolar transistors. These devices have the high input impedance of a
MOSFET and the low on−state conduction loss of a bipolar transistor.
The much lower on−state voltage drop varies only moderately
between 25°C and 150°C.
www.onsemi.com
C
The IGBT is ideal for many high voltage switching applications
operating at moderate frequencies where low conduction losses are
essential, such as: AC and DC motor controls, power supplies and
drivers for solenoids, relays and contactors.
G
Formerly developmental type TA49050.
E
Features
• 40 A, 600 V at T = 25°C
E
C
G
C
• 600 V Switching SOA Capability
• Typical Fall Time 140 ns at 150°C
• Short Circuit Rated
COLLECTOR
(FLANGE)
• Low Conduction Loss
TO−247−3LD SHORT LEAD
CASE 340CK
• Related Literature
JEDEC STYLE
♦ TB334 “Guidelines for Soldering Surface Mount Components to
PC Boards”
• This is a Pb−Free Device
MARKING DIAGRAM
$Y&Z&3&K
HG20N60B3
$Y
&Z
&3
&K
= ON Semiconductor Logo
= Assembly Plant Code
= Numeric Date Code
= Lot Code
HG20N60B3 = Specific Device Code
ORDERING INFORMATION
See detailed ordering and shipping information on page 6 of
this data sheet.
© Semiconductor Components Industries, LLC, 2004
1
Publication Order Number:
April, 2020 − Rev. 2
HGTG20N60B3/D
HGTG20N60B3
ABSOLUTE MAXIMUM RATINGS (T = 25°C unless otherwise specified)
C
Parameter
Symbol
HGTG20N60B3
Unit
V
Collector to Emitter Voltage
BV
600
600
CES
CGR
Collector to Gate Voltage, R = 1 MW
BV
A
GE
Collector Current Continuous
I
40
20
A
A
At T = 25°C
C25
C
I
At T = 110°C
C110
C
Collector Current Pulsed (Note 1)
Gate to Emitter Voltage Continuous
Gate to Emitter Voltage Pulsed
I
160
20
A
V
V
CM
V
GES
GEM
V
30
Switching Safe Operating Area at T = 150°C
SSOA
30 A at 600 V
165
C
Power Dissipation Total at T = 25°C
P
D
W
W/°C
°C
C
Power Dissipation Derating T > 25°C
1.32
C
Operating and Storage Junction Temperature Range
T , T
−40 to 150
J
STG
Maximum Temperature for Soldering
Leads at 0.063 in (1.6 mm) from Case for 10 s
Package Body for 10 s, see Tech Brief 334
T
300
260
°C
°C
L
T
pkg
SC
SC
Short Circuit Withstand Time (Note 2) at V = 15 V
t
t
4
ms
ms
GE
Short Circuit Withstand Time (Note 2) at V = 10 V
10
GE
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Repetitive Rating: Pulse width limited by maximum junction temperature.
2. V = 360 V, T =125°C, R = 25 W
CE
C
G
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise specified)
C
Parameter
Symbol
Test Condition
= 250 mA, V = 0 V
Min
600
20
−
Typ
−
Max
−
Unit
V
Collector to Emitter Breakdown Voltage
Emitter to Collector Breakdown Voltage
Collector to Emitter Leakage Current
BV
BV
I
I
I
CES
ECS
C
GE
= 10 mA, V = 0 V
−
−
V
C
GE
V
= BV
T
C
T
C
T
C
T
C
= 25°C
= 150°C
= 25°C
= 150°C
−
250
1.0
2.0
2.5
6.0
100
−
mA
mA
V
CES
CE
CES
−
−
Collector to Emitter Saturation Voltage
V
I
= I
C110
, V = 15 V
−
1.8
2.1
5.0
−
CE(SAT)
C
C
GE
−
V
Gate to Emitter Threshold Voltage
Gate to Emitter Leakage Current
Switching SOA
V
I
= 250 mA, V = V
GE
3.0
−
V
GE(TH)
CE
I
V
=
20 V
nA
A
GES
GE
SSOA
T
R
= 150°C, V = 15 V,
V
V
= 480 V
= 600 V
100
30
−
−
C
G
GE
CE
= 10 W, L = 45 mH
−
−
A
CE
Gate to Emitter Plateau Voltage
V
GEP
I
I
= I
C110
, V = 0.5 BV
CE CES
8.0
80
105
25
20
220
140
475
1050
−
−
V
C
On−State Gate Charge
Q
= I
CE
,
V
V
= 15 V
= 20 V
−
105
135
−
nC
nC
ns
ns
ns
ns
mJ
mJ
°C/W
G(ON)
C
V
C110
GE
= 0.5 BV
CES
−
GE
Current Turn−On Delay Time
Current Rise Time
t
T = 150°C,
−
d(ON)I
J
I
= I
,
CE
C110
t
rI
−
−
V
V
= 0.8 BV
= 15 V,
,
CE
GE
CES
Current Turn−Off Delay Time
Current Fall Time
t
−
275
175
−
d(OFF)I
R
= 10 W,
G
t
fI
−
L = 100 mH
Turn−On Energy
E
ON
−
Turn−Off Energy (Note 3)
Thermal Resistance
E
OFF
−
−
R
−
0.76
q
JC
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
3. Turn−Off Energy Loss (E
) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and
OFF
ending at the point where the collector current equals zero (I = 0 A). The HGTG20N60B3 was tested per JEDEC standard No. 24−1 Method
CE
for Measurement of Power Device Turn−Off Switching Loss. This test method produces the true total Turn−Off Energy Loss. Turn−On losses
include diode losses.
www.onsemi.com
2
HGTG20N60B3
TYPICAL PERFORMANCE CURVES
100
100
80
12 V
PULSE DURATION = 250 ms
DUTY CYCLE < 0.5%, V = 10 V
V
= 15 V
V
= 10 V
GE
GE
CE
PULSE DURATION = 250 ms,
DUTY CYCLE < 0.5%
80
60
40
20
0
T
C
= 25°C
T
C
= 150°C
V
= 9 V
GE
60
40
V
GE
= 8.5 V
= 8.0 V
T
C
= 25°C
T
C
= −40°C
V
GE
V
V
= 7.5 V
= 7.0 V
20
0
GE
GE
4
6
8
10
12
0
2
4
6
8
10
V
GE
, GATE TO EMITTER VOLTAGE (V)
V
CE
, COLLECTOR TO EMITTER VOLTAGE (V)
Figure 1. TRANSFER CHARACTERISTICS
Figure 2. SATURATION CHARACTERISTICS
100
50
40
PULSE DURATION = 250 ms
DUTY CYCLE < 0.5%,
T
C
= 25°C
80
60
40
20
V
GE
= 15 V
V
GE
= 15 V
T
C
= −40°C
30
20
T
C
= 150°C
10
0
0
25
50
75
100
125
150
0
1
2
3
4
5
T , CASE TEMPERATURE (°C)
C
V
CE
, COLLECTOR TO EMITTER VOLTAGE (V)
Figure 3. DC COLLECTOR CURRENT vs. CASE
TEMPERATURE
Figure 4. COLLECTOR TO EMITTER ON−STATE
VOLTAGE
5000
15
12
600
480
FREQUENCY = 1 MHz
CIES
4000
V
CE
= 600 V
I
R
= 1.685 mA,
= 30 W
g(REF)
360
240
3000
9
6
L
V
CE
= 400 V
2000
COES
V
CE
= 200 V
1000
120
0
3
0
CRES
T
= 25°C
C
0
0
5
10
15
20
25
0
20
40
60
80
100
V
CE
, COLLECTOR TO EMITTER VOLTAGE (V)
Q , GATE CHARGE (nC)
G
Figure 5. CAPACITANCE vs. COLLECTOR TO
EMITTER VOLTAGE
Figure 6. GATE CHARGE WAVEFORMS
www.onsemi.com
3
HGTG20N60B3
TYPICAL PERFORMANCE CURVES (continued)
100
500
T
J
= 150°C, R = 10 W, L = 100 mH
G
T = 150°C, R = 10 W, L = 100 mH
J G
400
300
V
CE
= 480 V, V = 15 V
GE
50
40
30
20
200
100
V
CE
= 480 V, V = 15 V
GE
10
0
10
20
30
40
0
10
20
30
40
I
, COLLECTOR TO EMITTER CURRENT (A)
I
, COLLECTOR TO EMITTER CURRENT (A)
CE
CE
Figure 7. TURN−ON DELAY TIME vs.
Figure 8. TURN−OFF DELAY TIME vs.
COLLECTOR TO EMITTER CURRENT
COLLECTOR TO EMITTER CURRENT
1000
100
10
100
10
1
T
J
= 150°C, R = 10 W, L = 100 mH
G
T
J
= 150°C, R = 10 W, L = 100 mH
G
V
CE
= 480 V, V = 15 V
GE
V
CE
= 480 V, V = 15 V
GE
0
10
20
30
40
0
10
20
30
40
I
, COLLECTOR TO EMITTER CURRENT (A)
I
, COLLECTOR TO EMITTER CURRENT (A)
CE
CE
Figure 9. TURN−ON RISE TIME vs.
COLLECTOR TO EMITTER CURRENT
Figure 10. TURN−OFF FALL TIME vs.
COLLECTOR TO EMITTER CURRENT
1400
1200
1000
800
600
400
200
0
2500
2000
T
J
= 150°C, R = 10 W, L = 100 mH
T = 150°C, R = 10 W, L = 100 mH
J G
G
V
CE
= 480 V, V = 15 V
V = 480 V, V = 15 V
CE GE
GE
1500
1000
500
0
0
10
20
30
40
0
10
20
30
40
I
, COLLECTOR TO EMITTER CURRENT (A)
I
, COLLECTOR TO EMITTER CURRENT (A)
CE
CE
Figure 11. TURN−ON ENERGY LOSS vs.
Figure 12. TURN−OFF ENERGY LOSS vs.
COLLECTOR TO EMITTER CURRENT
COLLECTOR TO EMITTER CURRENT
www.onsemi.com
4
HGTG20N60B3
TYPICAL PERFORMANCE CURVES (continued)
500
100
120
T
C
= 150°C, V = 15 V, R = 10 W
GE G
T
R
= 150°C, T = 75°C, V = 15 V,
J
C
GE
= 10 W, L = 100 mH
G
100
80
60
40
20
0
V
CE
= 480 V
f
f
P
= 0.05 / (t
+ t
d(ON)I
)
MAX1
MAX2
d(OFF)I
= (P − P ) / (E + E
)
D
C
ON
OFF
= ALLOWABLE DISSIPATION
= CONDUCTION DISSIPATION
(DUTY FACTOR = 50%)
= 0.76°C/W
D
C
P
R
q
JC
10
5
10
20
30
40
0
100
200
300
400
500
600
700
I
, COLLECTOR TO EMITTER CURRENT (A)
V
CE
, COLLECTOR EMITTER VOLTAGE (V)
CE
Figure 13. OPERATING FREQUENCY vs
COLLECTOR TO EMITTER CURRENT
Figure 14. SWITCHING SAFE OPERATING AREA
100
0.5
0.2
0.1
10−1
0.05
0.02
0.01
10−2
t
1
SINGLE PULSE
P
D
DUTY FACTOR, D = t / t
1
2
t
2
PEAK T = (P x Z
x R ) + T
q
JC C
q
J
D
JC
10−3
10−5
10−4
10−3
10−2
10−1
101
100
t , RECTANGULAR PULSE DURATION (s)
1
Figure 15. IGBT NORMALIZED TRANSIENT THERMAL RESPONSE, JUNCTION TO CASE
TEST CIRCUIT AND WAVEFORM
90%
L = 100 mH
10%
RHRP3060
V
GE
E
E
OFF
ON
V
CE
R
G
= 10 W
90%
+
10%
d(OFF)I
I
V
DD
= 480 V
CE
−
t
t
rI
t
fI
t
d(ON)I
Figure 16. INDUCTIVE SWITCHING TEST CIRCUIT
Figure 17. SWITCHING TEST WAVEFORMS
www.onsemi.com
5
HGTG20N60B3
HANDLING PRECAUTIONS FOR IGBTs
OPERATING FREQUENCY INFORMATION
Insulated Gate Bipolar Transistors are susceptible to
gate−insulation damage by the electrostatic discharge of
energy through the devices. When handling these devices,
care should be exercised to assure that the static charge built
in the handler’s body capacitance is not discharged through
the device. With proper handling and application
procedures, however, IGBTs are currently being extensively
used in production by numerous equipment manufacturers
in military, industrial and consumer applications, with
virtually no damage problems due to electrostatic discharge.
IGBTs can be handled safely if the following basic
precautions are taken:
Operating frequency information for a typical device
(Figure 13) is presented as a guide for estimating device
performance for a specific application. Other typical
frequency vs collector current (I ) plots are possible using
CE
the information shown for a typical unit in Figures 4, 7, 8, 11
and 12. The operating frequency plot (Figure 13) of a typical
device shows f
or f
whichever is smaller at each
MAX1
MAX2
point. The information is based on measurements of a
typical device and is bounded by the maximum rated
junction temperature.
f
is defined by f
= 0.05 / (t
+ t
).
MAX1
MAX1
d(OFF)I
d(ON)I
Deadtime (the denominator) has been arbitrarily held to
1. Prior to assembly into a circuit, all leads should be
kept shorted together either by the use of metal
shorting springs or by the insertion into conductive
material such as ECCOSORBDt LD26” or
equivalent.
10% of the on− state time for a 50% duty factor. Other
definitions are possible. t
Figure 17.
and t
are defined in
d(OFF)I
d(ON)I
Device turn−off delay can establish an additional
frequency limiting condition for an application other than
2. When devices are removed by hand from their
carriers, the hand being used should be grounded
by any suitable means − for example, with a
metallic wristband.
T
. t
is important when controlling output ripple
JM d(OFF)I
under a lightly loaded condition.
is defined by f = (P −P ) /(E
allowable dissipation (P ) is defined by P = (T − T ) /
f
+ E ). The
ON
MAX2
MAX2
D
C
OFF
D
D
JM
C
3. Tips of soldering irons should be grounded.
4. Devices should never be inserted into or removed
from circuits with power on.
R
. The sum of device switching and conduction losses
qJC
must not exceed P . A 50% duty factor was used (Figure 13)
and the conduction losses (P ) are approximated by
D
C
5. Gate Voltage Rating − Never exceed the
gate−voltage rating of VGEM. Exceeding the rated
VGE can result in permanent damage to the oxide
layer in the gate region.
P = (V x I ) / 2.
C CE CE
E
and E
are defined in the switching waveforms
ON
OFF
shown in Figure 17. E is the integral of the instantaneous
ON
power loss (I x V ) during turn−on and E is the
CE
CE
OFF
6. Gate Termination − The gates of these devices are
essentially capacitors. Circuits that leave the gate
open− circuited or floating should be avoided.
These conditions can result in turn−on of the
device due to voltage buildup on the input
integral of the instantaneous power loss (I x V ) during
CE CE
turn−off. All tail losses are included in the calculation for
; i.e., the collector current equals zero (I = 0).
E
OFF
CE
capacitor due to leakage currents or pickup.
7. Gate Protection - These devices do not have an
internal monolithic zener diode from gate to
emitter. If gate protection is required an external
zener is recommended.
ORDERING INFORMATION
Part Number
HGTG20N60B3
Package
Brand
Shipping
TO−247
HG20N60B3
450 Units / Tube
NOTE: When ordering, use the entire part number.
All brand names and product names appearing in this document are registered trademarks or trademarks of their respective holders.
www.onsemi.com
6
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
TO−247−3LD SHORT LEAD
CASE 340CK
ISSUE A
DATE 31 JAN 2019
P1
D2
A
E
P
A
A2
Q
E2
S
D1
D
E1
B
2
2
1
3
L1
A1
b4
L
c
(3X) b
(2X) b2
M
M
B A
0.25
MILLIMETERS
MIN NOM MAX
4.58 4.70 4.82
2.20 2.40 2.60
1.40 1.50 1.60
1.17 1.26 1.35
1.53 1.65 1.77
2.42 2.54 2.66
0.51 0.61 0.71
20.32 20.57 20.82
(2X) e
DIM
A
A1
A2
b
b2
b4
c
GENERIC
D
MARKING DIAGRAM*
D1 13.08
~
~
D2
E
0.51 0.93 1.35
15.37 15.62 15.87
AYWWZZ
XXXXXXX
XXXXXXX
E1 12.81
~
~
E2
e
L
4.96 5.08 5.20
5.56
15.75 16.00 16.25
3.69 3.81 3.93
3.51 3.58 3.65
XXXX = Specific Device Code
~
~
A
Y
= Assembly Location
= Year
WW = Work Week
ZZ = Assembly Lot Code
L1
P
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
P1 6.60 6.80 7.00
Q
S
5.34 5.46 5.58
5.34 5.46 5.58
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98AON13851G
TO−247−3LD SHORT LEAD
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
ADDITIONAL INFORMATION
TECHNICAL PUBLICATIONS:
Technical Library: www.onsemi.com/design/resources/technical−documentation
onsemi Website: www.onsemi.com
ONLINE SUPPORT: www.onsemi.com/support
For additional information, please contact your local Sales Representative at
www.onsemi.com/support/sales
相关型号:
HGTG20N60B3D_NL
Insulated Gate Bipolar Transistor, 40A I(C), 600V V(BR)CES, N-Channel, TO-247
FAIRCHILD
HGTG20N60C3DR
Insulated Gate Bipolar Transistor, 45A I(C), 600V V(BR)CES, N-Channel, TO-247
FAIRCHILD
HGTG20N60C3D_NL
Insulated Gate Bipolar Transistor, 45A I(C), 600V V(BR)CES, N-Channel, TO-247, LEAD FREE PACKAGE-3
FAIRCHILD
©2020 ICPDF网 联系我们和版权申明