KA2807MUX [ONSEMI]
接地漏电检测器;
| 型号： | KA2807MUX |
| 厂家： | 
ONSEMI |
| 描述： | 接地漏电检测器 光电二极管 |
| 文件： | 总7页 (文件大小：276K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
KA2807
Ground Fault Circuit
Interrupter
Description
The KA2807 is an IC for ground fault circuit interrupters which are
intended to provide an electrical shock hazard protection from line to
ground fault currents on grounded circuits of 120 V supplies.
www.onsemi.com
Features
RELATED STANDARDS
• Full Advantage of the UL943
• Built−In Voltage Regulator
• Sense Coil Ratio – 1000:1
UL943
• GND/Neutral Coil Ratio – 200:1
• Trip Time in Normal Fault and Grounded Neutral Fault is 18 ms Typ
• Wide Operating Temperature Range
• Excellent ESD Characteristic
SOIC8
CASE 751EB
Micro8
CASE 846A
• 1 mA Output Current Pulse to Trigger SCR
• Available in 8 Pin SOIC and 8 Pin MSOP
• Pb−Free Device
MARKING DIAGRAMS
8
1
8
1
ON
AYWZZ
KA2807
KA2807
AYWG
G
SOIC8
Micro8
KA2807 = Specific Device Code
A
Y
= Assembly Location
= Year
W
ZZ
G
= Work Week
= Assembly LOT Code
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
†
Device
Package
Shipping
KA2807DTF
SOIC
2,500 /
(Pb−Free)
Tape & Reel
KA2807MUX
Micro8
4,000 /
(Pb−Free)
Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2002
1
Publication Order Number:
July, 2019 − Rev. 2
KA2807/D
KA2807
PIN ASSIGNMENT
Trigger Out
VCC
1
2
3
4
8
7
6
5
− Input
+ Input
GND
Timing Capacitor
Timing Resistor
Amp Out
Figure 1. Pin Out KA2807 in 8−pin SOP or MSOP (Top View)
BLOCK DIAGRAM
TIMING
VCC
8
AMP OUT
5
RESISTOR
6
V. REG.
TIMING CONTROL
+INPUT
3
2
+
AMP
TIMING
CAPACITOR
7
−
−INPUT
LATCH
4
1
GND
TRIGGER OUT
Figure 2. KA2807 Block Diagram
www.onsemi.com
2
KA2807
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Min
Max
Unit
mA
W
I
Supply Current
−
+19
CC
P
D
Power Dissipation
SOIC−8
MSOP−8
−
−
0.41
0.3
T
Operating Temperature Range
Storage Temperature Range
−40
−55
+70
°C
°C
OPR
T
+150
STG
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
ELECTRICAL CHARACTERISTICS
Symbol
Parameter
Conditions
Pin 8, S1: 2, S2: OFF
Pin 3, S1: 2, S2: OFF
Pin 5, S1: 3, S2: ON
Min
23
Typ
26
Max
29
Unit
V
V
REG
Shunt Regulator Voltage
Amplifier Reference Voltage
Amplifier High Output Voltage
V
REF
9.5
17
10.5
19
11.5
21
V
V
OH
V
Sig: 800 Hz, 3.0 V
Sinusoidal wave
P−P
V
Amplifier Low Output Voltage
Amplifier Sensitivity Current
Latch On Voltage
Pin 5, S1: 3, S2: ON
1.5
3.5
2.5
5
3.5
6.5
V
mArms
V
OL
Sig: 800 Hz, 3.0 V
Sinusoidal wave
P−P
I
Pin 2, S1: 3, S2: ON
SEN
Sig: 800 Hz, 1.0 V
Sinusoidal wave
~ 2.5 V
P−P
P−P
V
Pin 7, S1: 3, S2: ON
16.5
0.5
17.5
1
19.5
2.0
ON(LATCH)
Sig: 800 Hz, 3.0 V
Sinusoidal wave
P−P
I
TR
SCR Trigger Current
Pin 1, S1: 3, S2: ON
mA
Sig: 800 Hz, 3.0 V
Sinusoidal wave
P−P
V 1
Output Low Voltage
Output Impedance
Output Sink Current
Pin 1, S1: 2, S2: OFF
Pin 1, S1: 2, S2: OFF
Pin 1, S1: 2, S2: OFF
−
−
100
100
6.0
240
250
−
mA
W
S
Z
O
I
2.0
mA
SINK
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
3
KA2807
TEST CIRCUIT
V
CC
= 31 V
I
= 5 mA
CC
1 kW
1.45 MW
0.002 mF
8
1
7
2
6
3
5
4
KA2807
S1
2
A3
1
3
A1
A2
100 kW
1 kW
0.3 V
S2
0.047 mF
SIG
Figure 3. KA2807 Test Circuit
www.onsemi.com
4
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SOIC8
CASE 751EB
ISSUE A
DATE 24 AUG 2017
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98AON13735G
SOIC8
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
Micro8
CASE 846A−02
ISSUE K
DATE 16 JUL 2020
SCALE 2:1
GENERIC
MARKING DIAGRAM*
8
XXXX
AYWG
G
1
XXXX = Specific Device Code
A
Y
W
G
= Assembly Location
= Year
= Work Week
= Pb−Free Package
STYLE 1:
STYLE 2:
PIN 1. SOURCE 1
STYLE 3:
PIN 1. SOURCE
PIN 1. N-SOURCE
2. N-GATE
(Note: Microdot may be in either location)
2. SOURCE
3. SOURCE
4. GATE
2. GATE 1
3. SOURCE 2
4. GATE 2
3. P-SOURCE
4. P-GATE
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
5. DRAIN
6. DRAIN
7. DRAIN
8. DRAIN
5. DRAIN 2
6. DRAIN 2
7. DRAIN 1
8. DRAIN 1
5. P-DRAIN
6. P-DRAIN
7. N-DRAIN
8. N-DRAIN
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98ASB14087C
MICRO8
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
ADDITIONAL INFORMATION
TECHNICAL PUBLICATIONS:
Technical Library: www.onsemi.com/design/resources/technical−documentation
onsemi Website: www.onsemi.com
ONLINE SUPPORT: www.onsemi.com/support
For additional information, please contact your local Sales Representative at
www.onsemi.com/support/sales
相关型号：
KA2821D
The KA2821D is a monolithic integrated circuit, and suit able as a two-phase stepping motor driver of a 3.5-inch FDD system
FAIRCHILD
©2020 ICPDF网 联系我们和版权申明