LC06511FMX [ONSEMI]
Battery Protection IC, OTP Function, 1-Cell Lithium-Ion Battery;型号: | LC06511FMX |
厂家: | ONSEMI |
描述: | Battery Protection IC, OTP Function, 1-Cell Lithium-Ion Battery 电池 |
文件: | 总13页 (文件大小:277K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Battery Protection IC, OTP
Function, 1-Cell Lithium-Ion
Battery
LC06511FMX
Overview
www.onsemi.com
LC06511FMX is a protection IC for 1 cell lithium−ion or
lithium−polymer battery. It provides highly accurate over−charge,
over−discharge, over−current protection. Current is detected by high
precision external chip resistor. Which realizes accurate current
detection over temperature.
1
Function
X2DFN6 1.4x1.4, 0.5P
CASE 716AF
• Highly Accurate Detection Voltage/Current at Ta = 25°C,
VCC = 3.8 V
• Over Charge Detection Voltage
♦ 4.276 V, 4.426 V, 4.476 V
• Over Charge Release Hysteresis
♦ 0.2 V
• Over Discharge Detection Voltage
♦ 2.3 V, 2.5 V, 2.8 V
MARKING DIAGRAM
XXMG
G
XX = Specific Device Code
M
G
= Month Code
= Pb−Free Package
• Over Discharge Release Hysteresis2
♦ 0.2 V
(Note: Microdot may be in either location)
• Discharge Over Current Detection Voltage1
♦ 6.3 mV, 7.5 mV
• Short Current Detection Voltage
♦ 30 mV
• Charge Over Current Detection Voltage
♦ 5.0 mV, 6.0 mV
• Over−discharge Detection Delay Time
♦ 32 ms
• Discharge Over−current Detection Delay Time1
♦ 16 ms
ORDERING INFORMATION
†
Device
Package
Shipping
LC06511FXXMXTBG
X2DFN6
4000 /
(Pb−Free) Tape & Reel
XX = 1A−9A, 1B−9B
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
• 0 V Battery Charging
♦ “Permit”
• Auto Wake−up Function
♦ “Permit”
• This is a Pb−Free Device
Typical Applications
• Smart Phone
• Tablet
• Wearable Device
© Semiconductor Components Industries, LLC, 2020
1
Publication Order Number:
April, 2020 − Rev. 1
LC06511FMX/D
LC06511FMX
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter
Supply voltage
Symbol
Conditions
Ratings
−0.3 to 12.0
Unit
V
VCC
VCS
VVM
VCO
VDO
Tstg
Topr
Tj
CS terminal Input voltage
VM terminal Input voltage
CO terminal voltage
−0.3 to 7
V
VCC − 24.0 to VCC + 0.3
VCC − 24.0 to VCC + 0.3
VCC − 0.3 to VCC + 0.3
−55 to +125
V
V
DO terminal voltage
V
Storage temperature
Operating ambient temperature
Junction temperature
_C
_C
_C
−40 to +85
125
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
EXAMPLE OF APPLICATION CIRCUIT
Battery+
PAC+
R1
C1
Controller IC
VCC
Over current
detection
OTP
CO
VSS
DO
VM
R2
CS
R3
Sense Resistor
Battery−
PAC−
External FETs
Figure 1. Example of Application Circuit
Table 2.
Components
Min
0.1
0.1
0.01
1
Recommended Value
Max
1
Unit
kW
Description
R1
R2
C1
R3
0.33
1
Battery+ is filtered to VCC by R1 and C1
Protection from reverse connection of charger
Battery+ is filtered to VCC by R1 and C1
Sence resistor for over−current detection
2
kW
0.1
1.0
20
mF
mW
www.onsemi.com
2
LC06511FMX
Table 3. ELECTRICAL CHARACTERISTICS (R1 = 0.33 kW, R2 = 1 kW, VCC = 3.8 V (Note 1))
Test
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Unit
Circuit
DETECTION VOLTAGE
Over−charge Detection
Vov
R1 = 0.33 kW
Ta = 25°C
Vov_set − 10
Vov_set − 15
Vov_set
Vov_set
Vov_set + 10
Vov_set + 15
mV
B
B
I
Voltage
Ta =
−20 to 60°C
Over−charge Release
Voltage
Vovr1
Vovr2
Vuv
R1 = 0.33 kW
VM < Vcocr&
CS = 0 V
Ta = 25°C
Vovr_set − 30
Vovr_set − 55
Vovr_set
Vovr_set
Vovr_set + 30
Vovr_set + 40
mV
mV
mV
mV
mV
mV
mV
V
Ta =
−20 to 60°C
R1 = 0.33 kW
VM > Vcocr&
CS = 0 V
Ta = 25°C
Vov_set − 15
Vov_set − 20
Vov_set
Vov_set
Vov_set + 10
Vov_set + 15
Ta =
−20 to 60°C
Over−discharge Detection
Voltage
R1 = 0.33 kW
Ta = 25°C
Vuv_set − 35
Vuv_set − 55
Vuv_set
Vuv_set
Vuv_set + 35
Vuv_set + 55
B
B
D
F
F
A
F
A
Ta =
−20 to 60°C
Over−discharge Release
Voltage1
Vuvr1
Vuvr2
Vdoc
Vshrt
Vdocr
Vcoc
Vcocr
R1 = 0.33 kW
VM = 0 V
Ta = 25°C
Vuv_set – 35
Vuv_set – 55
Vuv_set
Vuv_set
Vuv_set + 50
Vuv_set + 80
Ta =
−20 to 60°C
Over−discharge Release
Voltage2
R1 = 0.33 kW
VM = OPEN
Ta = 25°C
Vuvr_set − 100
Vuvr_set − 110
Vuvr_set
Vuvr_set
Vuvr_set + 100
Vuvr_set + 110
Ta =
−20 to 60°C
Discharge Over−current
Detection Voltage
(Primary Protection)
R2 = 1 kW
VCC = 3.8 V
Ta = 25°C
Vdoc_set − 1.0
Vdoc_set − 1.8
Vdoc_set
Vdoc_set
Vdoc_set + 1.0
Vdoc_set + 1.8
Ta =
−20 to 60°C
Discharge Over−current
Detection Voltage
(Short Circuit)
R2 = 1 kW
VCC = 3.8 V
Ta = 25°C
Vshrt_set − 10
Vshrt_set − 12
Vshrt_set
Vshrt_set
Vshrt_set + 10
Vshrt_set + 12
Ta =
−20 to 60°C
Discharge Over−current
(Short Circuit) Release
Voltage
R2 = 1 kW
VCC = 3.8 V
CS = 0 V
Ta = 25°C
VCC − 1.1
VCC − 1.2
VCC−0.65
VCC−0.65
VCC − 0.2
VCC − 0.1
Ta =
−20 to 60°C
Charge Over−current
Detection Voltage
R2 = 1 kW
VCC = 3.8 V
Ta = 25°C
Vcoc_set − 1.0
Vcoc_set − 1.8
Vcoc_set
Vcoc_set
Vcoc_set + 1.0
Vcoc_set + 1.8
mV
V
Ta =
−20 to 60°C
Charge Over−current
Release Voltage
R2 = 1 kW
VCC = 3.8 V
CS = 0 V
Ta = 25°C
0.08
0.05
0.2
0.2
0.32
0.35
Ta =
−20 to 60°C
INPUT VOLTAGE
0 V Battery Charge
Permission Charger Voltage
Vchg
VCC − VM
VCC =
VSS = 0 V
Ta = 25°C
1.4
V
A
CURRENT CONSUMPTION
Operating Current
Icc
At normal
state
Ta = 25°C
3
6
mA
mA
J
J
VCC = 3.8 V
Stand−by Current
Istb
At stand−by
Ta = 25°C
VCC = 2.0 V
0.95
state
Auto
wake−up
= enable
www.onsemi.com
3
LC06511FMX
Table 3. ELECTRICAL CHARACTERISTICS (R1 = 0.33 kW, R2 = 1 kW, VCC = 3.8 V (Note 1)) (continued)
Test
Parameter
RESISTANCE
Symbol
Conditions
Min.
Typ.
Max.
Unit
Circuit
Internal Resistance
Rvmu
Rvmd
Rcoh
VCC = 2.0 V
Ta = 25°C
Ta = 25°C
Ta = 25°C
150
5
300
10
600
20
kW
kW
kW
E
E
H
(VCC−VM)
VM = 0 V
Internal Resistance
(VSS−VM)
VCC = 3.8 V
VM = 0.1 V
CO Output Resistance
(High)
VCC = 3.8 V
CO = 3.3 V
CS = 0 V
6
12
24
CO Output Resistance (Low)
Rcol
Rdoh
Rdol
VCC = 4.5 V
CO = 0.5 V
CS = 0 V
Ta = 25°C
Ta = 25°C
Ta = 25°C
0.5
0.5
0.2
0.7
1.0
0.3
2.0
2.0
0.8
kW
kW
kW
H
G
G
DO Output Resistance
(High)
VCC = 3.8 V
DO = 3.3 V
CS = 0 V
DO Output Resistance (Low)
VCC = 2.0 V
CS = 0 V
DO = 0.5 V
DETECTION AND RELEASE DELAY TIME
Over−charge Detection
Tov
Tovr
Tuv
VCC = 3 V to
4.6 V
VM = CS =
0 V
Ta = 25°C
819
717
1024
1024
1229
1331
ms
ms
ms
ms
B
B
B
B
Delay Time
Ta =
−20 to 60°C
Over−charge Release Delay
Time
VCC = 4.6 V
to 3 V
VM = CS =
0 V
Ta = 25°C
12.8
11.2
16
16
19.2
20.8
Ta =
−20 to 60°C
Over−discharge Detection
Delay Time
VCC = 3.5 V
to 1.8 V
VM = CS =
0 V
Ta = 25°C
Tuv_set * 0.8
Tuv_set * 0.65
Tuv_set
Tuv_set
Tuv_set * 1.2
Tuv_set * 1.35
Ta =
−20 to 60°C
Over−discharge Release
Delay Time
Tuvr
VCC = 1.8 V
to 3.5 V
VM = CS =
0 V
Ta = 25°C
0.84
0.68
1.05
1.05
1.26
1.42
Ta =
−20 to 60°C
Discharge Over−current
Tdoc1
Tdocr
Tshrt
CS = 0 V to
VdocMAX
VM = 0 V
Ta = 25°C
Tdoc1_set * 0.8
Tdoc1_set * 0.7
Tdoc1_set
Tdoc1_set
Tdoc1_set * 1.2
Tdoc1_set * 1.3
ms
ms
ms
F
A
F
F
F
Detection Delay Time 1
Ta =
−20 to 60°C
Discharge Over−current
Release Delay Time
VM = 3.8 V
to 2.65 V
CS = 0 V
Ta = 25°C
3.2
2.8
4
4
4.8
5.2
Ta =
−20 to 60°C
Short−current
Detection Delay Time
CS = 0 V to
VshrtMAX
VM = 0
Ta = 25°C
175
150
250
250
325
350
Ta =
−20 to 60°C
Charge Over−current
Detection Delay Time
Tcoc
CS = 0 V to
VcocMIN
VM = 0
Ta = 25°C
12.8
11.2
16
16
19.2
20.8
ms
ms
Ta =
−20 to 60°C
Charge Over−current
Release Delay Time
Tcocr
VM = 0 V to
VcocrMAX
CS = 0 V
Ta = 25°C
3.2
2.8
4
4
4.8
5.2
Ta =
−20 to 60°C
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
1. The specifications in high temperature and low temperature are guaranteed by design.
www.onsemi.com
4
LC06511FMX
TEST CIRCUITS
A
F
R1
R2
R1
R2
VCC
VM
VCC
VM
DO
CO
DO
CO
V
V
CS
CS
V
VSS
VSS
B
G
R1
VCC
R1
R2
VCC
R2
DO
VM
A
DO
CO
V
VM
CS
CO
CS
VSS
VSS
C
H
R1
R1
R2
VCC
VCC
VM
R2
DO
DO
CO
VM
CS
CS
CO
A
VSS
VSS
D
I
R1
R1
VCC
VM
VCC
VM
R2
DO
CO
DO
CO
V
CS
CS
VSS
VSS
E
J
R1
R1
R2
VCC
VM
VCC
VM
R2
DO
CO
DO
CO
A
A
CS
CS
V
VSS
VSS
Figure 2. Test Circuits
www.onsemi.com
5
LC06511FMX
Table 4. SELECTION GUIDE
Vov
Specific
Device
Code
Vovr
(mV)
Vuv
(mV)
Vuvr2
(mV)
Vdoc
(mV)
Vshrt
(mV)
Vcoc
(mV)
Tuv
(ms)
Tdoc1
(ms)
(mV)
Device
LC06511F1AMX
LC06511F1BMX
LC06511F2AMX
LC06511F2BMX
LC06511F3AMX
LC06511F3BMX
LC06511F4AMX
LC06511F4BMX
LC06511F5AMX
LC06511F5BMX
LC06511F6AMX
LC06511F6BMX
LC06511F7AMX
LC06511F7BMX
LC06511F8AMX
LC06511F8BMX
LC06511F9AMX
LC06511F9BMX
4276
4276
4426
4426
4476
4476
4276
4276
4426
4426
4476
4476
4276
4276
4426
4426
4476
4476
4076
4076
4226
4226
4276
4276
4076
4076
4226
4226
4276
4276
4076
4076
4226
4226
4276
4276
2300
2300
2300
2300
2300
2300
2500
2500
2500
2500
2500
2500
2800
2800
2800
2800
2800
2800
2500
2500
2500
2500
2500
2500
2700
2700
2700
2700
2700
2700
3000
3000
3000
3000
3000
3000
6.3
7.5
6.3
7.5
6.3
7.5
6.3
7.5
6.3
7.5
6.3
7.5
6.3
7.5
6.3
7.5
6.3
7.5
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
−5
−6
−5
−6
−5
−6
−5
−6
−5
−6
−5
−6
−5
−6
−5
−6
−5
−6
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
LL
LW
LM
LX
LN
LY
LP
LZ
LQ
L2
LR
L3
LT
L4
LU
L5
LV
L6
Table 5. SENSE RESISTOR SELECTION GUIDE
LC06511F 1A−9A MX
LC06511F 1B−9B MX
Vcoc
Vdoc
Vshrt
Vcoc
Vdoc
Vshrt
−5.0 mV
6.3 mV
30 mV
−6.0 mV
7.5 mV
30 mV
Charge
Over Current
[A]
Discharge
Over Current
[A]
Charge
Over Current
[A]
Discharge
Over Current
[A]
Short Current
[A]
Short Current
[A]
Sense
Resistor
[mW]
2
3
2.5
1.7
1.3
1
3.2
2.1
1.6
1.3
1.1
0.9
0.8
0.7
0.6
15
10
7.5
6
3
3.8
2.5
1.9
1.5
1.3
1.1
0.9
0.8
0.8
15
10
7.5
6
2
4
1.5
1.2
1
5
6
0.8
0.7
0.6
0.6
0.5
5
5
7
4.3
3.8
3.3
3
0.9
0.8
0.7
0.6
4.3
3.8
3.3
3
8
9
10
www.onsemi.com
6
LC06511FMX
Table 6. PIN FUNCTION
Pin No.
Symbol
Pin Function
1
2
3
4
5
6
VM
CO
Charger negative voltage input terminal
Charge FET control terminal
Discharge FET control terminal
VSS terminal
DO
VSS
VCC
CS
VCC terminal
Over−current detection input terminal
BLOCK DIAGRAM
VCC
5
OSC
Power
Control
Level
Shifter
Control Circuit
Rvmu
Rvmd
1
VM
Short current
Detector
Over−discharge
Detector
1.2V
Discharge
Over−current
Detector 1
Over− charge
Detector
Comp for
Vdocr
Charge
Over−current
Detector
Comp for
Vcocr
OTP
4
3
2
6
VSS
CS
DO
CO
Figure 3. Block Diagram
www.onsemi.com
7
LC06511FMX
DESCRIPTION OF OPERATION
4. Discharging Over−current State
• Discharge Over−current Detection
• The battery voltage is detected between VCC pin and
VSS pin and the battery current is detected between VSS
pin and CS pin.
CS terminal is higher than or equal to “discharge
over−current detection voltage (Vdoc)” for longer than
“discharge over−current detection delay time (Tdoc1)”.
DO is low level output. Discharge is prohibited.
• Discharge Over−current Detection (Short Circuit)
CS terminal is higher than or equal to “discharge
over−current detection voltage (Short circuit) (Vshrt)”
for longer than “short−current detection delay time
(Tshrt)”.
1. Normal State
• “VCC voltage” is between “over−discharge detection
voltage (Vuv)”, “over−charge detection voltage (Vov)”,
and “CS voltage” is between “charge over−current
detection voltage (Vcoc)”, “discharge over−current
detection voltage (Vdoc)”, and “VM voltage” is lower
than “dicharge over−current (short) release voltage
(Vdocr)”.
DO is low level output. Dischaege is prohibited.
During discharging over−current state, VM pin is pulled
down to Vss by internal resistor (Rvmd).
This is the normal state. Both CO and DO are high level
output. Charge and discharge is allowed.
• Release from Discharging Over−current State
“CS voltage” goes lower than “discharge over−current
detection voltage (Vdoc)” and VM voltage goes lower
than “discharge over−current (short) release voltage
(Vdocr)” for longer than “discharge over−current release
delay time (Tdocr)”.
2. Over−charging State
• “VCC voltage” is higher than or equal to “over−charge
detection voltage (Vov)” for longer than “over−charge
detection delay time (Tov)”.
This is the over−charging state, CO is low level output.
Charge is prohibited.
• Release from Over−charging State 1
5. Charging Over−current State
“VM voltage” is lower than “charge over−current (short)
release voltage (Vcocr)”. Then “VCC voltage” is lower
than “over−charge release voltage (Vovr)” for longer than
“over−charging release delay time (Tovr)”.
• “CS voltage” goes lower than or equal to “charge
over−current detection voltage (Vcoc) for longer than
“charge over−current detection delay time (Tcoc)”.
This is the charging over−current state, CO is low level
output. Charge is prohibited.
• Release from charging over−current state
“CS voltage” goes higher than “charge over−current
detection voltage (Vcoc)” and “VM voltage” goes higher
than “charge over−current release voltage (Vcocr)” for
longer than “charge over−current release delay time
(Tcocr)”.
• Release from Over−charging State 2
“VM voltage” is higher than “charge over−current (short)
release voltage (Vcocr)”. Then “VCC voltage” is lower
than “over−charge detection voltage (Vov) for longer than
“over−charge release delay time (Tovr)”.
3. Over−discharging State
• “VCC voltage” is lower than “over−discharge detection
voltage (Vuv)” for longer than “over−discharge delay
time (Tuv)”.
6. 0 V Battery Charging
• When the Battery voltage is lower than or equal to “0 V
battery charge permission voltage (Vchg)”, charge is
allowed if charger voltage is higher than or equal “0 V
battery charge permission voltage (Vchg)”. CO is fixed
by the “VCC voltage”.
This is the over−discharging state, DO is low level output.
Discharge is prohibited.
During over−discharging state, VM pin is pulled up to
Vcc by internal resistor (Rvmu) and circuits are shut
down. The low power consumption is kept.
• Release from Over−discharging State 1
Charger is connected, then “VCC voltage” goes higher
than “over−discharge release voltage1 (Vuvr1)” for
longer than “over−charge release delay time (Tuvr)”.
• Release from Over−discharging State (with Auto
Wake−up Feature) 2
“VCC voltage” is higher than “over−discharge release
voltage2 (Vuvr1)” without charger for longer than
“over−charge release delay time (Tovr)”.
www.onsemi.com
8
LC06511FMX
TIMING CHARTS
Over Charge Voltage and Charge Over Current
Charger Load Charger
connection connection connection connection
Load
Charger
connection
Load
connection
VCC
Vov
Vovr
t
CS
Vshrt
Vdoc
VSS
Vcoc
t
VM
VCC
Vcocr
VSS
t
CO
VCC
Tovr
Tcocr
Tcoc
Tov
Tov
Tovr
VM
t
t
Icharge
0
Idischarge
Figure 4. Over Charge Voltage and Charge Over Current
www.onsemi.com
9
LC06511FMX
Over Discharge Detection and Release (with/without Charger)
Load
connection
Load
connection
Charger
connection
VCC
Vuvr2
Vuvr1
Vuv
t
CS
Vshrt
Vdoc
VSS
Vcoc
t
VM
VCC
VSS
t
DO
VCC
Tuv
Tuvr
Tuvr
Tuv
VSS
t
t
Icharge
0
Idischarge
Figure 5. Over Discharge Detection and Release (with/without Charger)
www.onsemi.com
10
LC06511FMX
Discharge Over Current and Short Current Detection and Release
Load
Charger
Load
Charger
Short
Charger
connection
connection
connection
connection
circuit connection
VCC
t
CS
Vshrt
Vdoc
VSS
Vcoc
t
VM
VCC
VSS
t
DO
VCC
Tdoc1
Tdoc1
Tshrt
Tdocr
Tdocr
Tdocr
VSS
t
t
Icharge
0
Idischarge
Figure 6. Discharge Over Current and Short Current Detection and Release
www.onsemi.com
11
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
X2DFN6 1.4x1.4, 0.5P
CASE 716AF
ISSUE A
1
DATE 11 MAY 2018
SCALE 4:1
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.10 AND
0.20 mm FROM THE TERMINAL TIP.
A
B
D
A3
A1
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
PIN ONE
REFERENCE
E
MILLIMETERS
DIM MIN
NOM MAX
PLATED
SURFACE
A
A1
A3
b
0.30
−−−
0.35
−−−
0.40
0.05
DETAIL B
TOP VIEW
0.127 REF
0.20
1.40
0.96
1.40
DETAIL B
0.15
1.30
0.25
1.50
1.06
1.50
0.30
D
A
C
D2 0.86
1.30
0.10
C
C
E
E2 0.10
0.20
e
K
L
0.50 BSC
0.25 REF
0.35
0.05
SEATING
PLANE
NOTE 4
0.30
0.40
SIDE VIEW
D2
GENERIC
MARKING DIAGRAM*
6X L
DETAIL A
1
3
E2
XXMG
G
XX = Specific Device Code
6
4
K
M
G
= Month Code
= Pb−Free Package
6X b
M
0.10
C A B
e
(Note: Microdot may be in either location)
NOTE 3
BOTTOM VIEW
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present. Some products
may not follow the Generic Marking.
RECOMMENDED
SOLDERING FOOTPRINT*
6X
0.50
1.16
1.70
0.20
1
0.50
PITCH
6X
0.20
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98AON79890G
X2DFN6 1.4x1.4, 0.5P
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
ON Semiconductor Website: www.onsemi.com
◊
www.onsemi.com
相关型号:
©2020 ICPDF网 联系我们和版权申明