MC100E142 [ONSEMI]
9-BIT SHIFT REGISTER; 9位移位寄存器
| 型号： | MC100E142 |
| 厂家： | 
ONSEMI |
| 描述： | 9-BIT SHIFT REGISTER |
| 文件： | 总4页 (文件大小：112K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SEMICONDUCTOR TECHNICAL DATA
The MC10E/100E142 is a 9-bit shift register, designed with byte-parity
applications in mind. The E142 performs serial/parallel in and
serial/parallel out, shifting in one direction. The nine inputs D0 – D8
accept parallel input data, while S-IN accepts serial input data. The Qn
outputs do not need to be terminated for the shift operation to function. To
minimize noise and power, any Q output not used should be left
unterminated.
9-BIT SHIFT
REGISTER
• 700MHz Min. Shift Frequency
• 9-Bit for Byte-Parity Applications
• Asynchronous Master Reset
• Dual Clocks
• Extended 100E V
Range of – 4.2V to – 5.46V
EE
• 75kΩ Input Pulldown Resistors
The SEL (Select) input pin is used to switch between the two modes of
operation — SHIFT and LOAD. The shift direction is from bit 0 to bit 8.
Input data is accepted by the registers a set-up time before the positive
going edge of CLK1 or CLK2; shifting is also accomplished on the positive
clock edge. A HIGH on the Master Reset pin (MR) asynchronously resets
all the resisters to zero.
FN SUFFIX
PLASTIC PACKAGE
CASE 776-02
SEL
25
D
D
D
D
V
Q
8
8
7
6
5
CCO
24
23
22
21
20
19
MR
CLK1
CLK2
18
17
16
15
14
13
26
Q
Q
7
27
28
6
LOGIC DIAGRAM
S-IN
V
CC
1
0
Q
Q
Q
Q
Q
Q
Q
Q
0
1
2
3
D
D
0
Pinout: 28-Lead PLCC
V
1
2
EE
Q
V
5
(Top View)
S-IN
1
0
CCO
D
D
D
D
1
2
D
0
3
Q
4
3
D
1
1
0
4
12
Q
D
5
6
7
8
9
10
11
1
0
D
2
D
D
V
Q
0
Q
1
Q
2
3
4
CCO
D
3
* All V
and V
CCO
pins are tied together on the die.
CC
PIN NAMES
Pin
Function
D
S-IN
SEL
CLK1, CLK2
MR
– D
Parallel Data Inputs
Serial Data Input
Mode Select Input
Clock Inputs
0
8
Q
Q
1
0
8
D
D
8
Master Reset
SEL
Q
– Q
Data Outputs
0
8
CLK1
CLK2
FUNCTIONS
SEL
Mode
MR
L
H
Load
Shift
12/93
REV 2
Motorola, Inc. 1996
MC10E142 MC100E142
DC CHARACTERISTICS (V
= V (min) to V (max); V
EE EE
= V = GND)
CCO
EE
CC
0°C
25°C
85°C
Symbol
Characteristic
Input HIGH Current
min
typ
max
min
typ
max
min
typ
max Unit Condition
I
IH
150
150
150
µA
I
Power Supply Current
mA
EE
10E
100E
120
120
145
145
120
120
145
145
120
138
145
165
AC CHARACTERISTICS (V
= V (min) to V (max); V
EE EE
= V = GND)
CCO
EE
CC
0°C
25°C
85°C
typ
Symbol
Characteristic
min
typ
max
min
typ
max
min
max Unit Condition
f
Max. Shift Frequency
700
900
700
900
700
900
MH
z
SHIFT
t
t
Propagation Delay to Output
ps
PLH
PHL
Clk
MR
600
600
800
800
1000
1000
600
600
800
800
1000
1000
600
600
800
800
1000
1000
t
Setup Time
ps
ps
s
D
SEL
50
300
–100
150
50
300
–100
150
50
300
–100
150
t
h
Hold Time
D
SEL
300
75
100
–150
300
75
100
–150
300
75
100
–150
t
t
Reset Recovery Time
900
700
900
700
900
700
ps
ps
RR
Minimum Pulse Width
Clk, MR
PW
400
400
400
t
Within-Device Skew
75
75
75
ps
ps
Note 1
SKEW
t
r
t
f
Rise/Fall Times
20 - 80%
300
525
800
300
525
800
300
525
800
1. Within-device skew is defined as identical transitions on similar paths through a device.
MOTOROLA
2–2
MC10E142 MC100E142
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776–02
ISSUE D
M
S
S
0.007 (0.180)
T
L –M
N
B
Z
Y BRK
D
-N-
M
S
S
0.007 (0.180)
T
L –M
N
U
-L-
-M-
D
W
X
G1
S
S
S
0.010 (0.250)
0.007 (0.180)
T
L –M
L –M
N
V
28
1
VIEW D-D
M
M
S
S
S
0.007 (0.180)
0.007 (0.180)
T
T
L –M
L –M
N
A
R
H
M
S
S
T
N
Z
S
N
K1
C
E
0.004 (0.100)
SEATING
PLANE
G
K
-T-
VIEW S
J
M
S
S
0.007 (0.180)
T
L –M
N
F
G1
VIEW S
S
S
S
0.010 (0.250)
T
L –M
N
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIM G1, TRUE POSITION TO BE MEASURED
AT DATUM -T-, SEATING PLANE.
INCHES
MAX
MILLIMETERS
3. DIM R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
MIN
MIN
12.32
12.32
4.20
MAX
12.57
12.57
4.57
0.485
0.495
0.495
0.180
0.110
0.019
0.485
0.165
0.090
0.013
2.29
2.79
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
0.33
0.48
0.050 BSC
1.27 BSC
0.026
0.032
—
—
0.456
0.456
0.048
0.048
0.056
0.020
0.66
0.51
0.64
11.43
11.43
1.07
1.07
1.07
—
0.81
—
—
11.58
11.58
1.21
1.21
1.42
0.50
0.020
0.025
0.450
0.450
0.042
0.042
0.042
—
2
°
10°
2°
10°
0.410
0.040
0.430
—
10.42
1.02
10.92
—
2–3
MOTOROLA
MC10E142 MC100E142
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, includingwithoutlimitationconsequentialorincidentaldamages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC10E142/D
◊
相关型号：
MC100E142FNR2
100E SERIES, 9-BIT RIGHT PARALLEL IN PARALLEL OUT SHIFT REGISTER, TRUE OUTPUT, PQCC28, PLASTIC, LCC-28
MOTOROLA
©2020 ICPDF网 联系我们和版权申明