MC10109 [ONSEMI]
Dual 4-5-Input OR/NOR Gate; 双4-5输入或/或非门
| 型号： | MC10109 |
| 厂家： | 
ONSEMI |
| 描述： | Dual 4-5-Input OR/NOR Gate |
| 文件： | 总5页 (文件大小：104K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SEMICONDUCTOR TECHNICAL DATA
The MC10109 is a dual 4–5 input OR/NOR gate.
P
= 30 mW typ/gate (No Load)
= 2.0 ns typ
D
t
pd
t , t = 2.0 ns typ (20%–80%)
r f
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
LOGIC DIAGRAM
4
5
FN SUFFIX
PLCC
CASE 775–02
3
2
6
7
9
10
11
12
13
14
15
DIP
PIN ASSIGNMENT
V
A
V
B
B
B
B
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
CC1
CC2
OUT
OUT
IN
OUT
OUT
V
V
V
= PIN 1
= PIN 16
= PIN 8
CC1
CC2
EE
A
A
IN
A
IN
IN
B
B
B
A
IN
IN
IN
IN
A
IN
V
EE
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
3/93
Motorola, Inc. 1996
REV 5
MC10109
ELECTRICAL CHARACTERISTICS
Test Limits
+25°C
Typ
Pin
Under
Test
–30°C
+85°C
Characteristic
Power Supply Drain Current
Input Current
Symbol
Unit
mAdc
µAdc
µAdc
Vdc
Min
Max
15
Min
Max
14
Min
Max
15
I
E
8
4
4
11
I
425
265
265
inH
I
0.5
0.5
0.3
inL
Output Voltage
Logic 1
V
OH
2
3
–1.060
–1.060
–0.890
–0.890
–0.960
–0.960
–0.810
–0.810
–0.890
–0.890
–0.700
–0.700
Output Voltage
Logic 0
Logic 1
Logic 0
V
2
3
–1.890
–1.890
–1.675
–1.675
–1.850
–1.850
–1.650
–1.650
–1.825
–1.825
–1.615
–1.615
Vdc
Vdc
Vdc
ns
OL
Threshold Voltage
Threshold Voltage
V
OHA
2
3
–1.080
–1.080
–0.980
–0.980
–0.910
–0.910
V
OLA
2
3
–1.655
–1.655
–1.630
–1.630
–1.595
–1.595
Switching Times (50Ω Load)
Propagation Delay
t
t
t
t
2
2
3
3
1.0
1.0
1.0
1.0
3.7
3.7
3.7
3.7
1.0
1.0
1.0
1.0
2.0
2.0
2.0
2.0
2.9
2.9
2.9
2.9
1.0
1.0
1.0
1.0
3.7
3.7
3.7
3.7
4+2+
4–2–
4+3–
4–3+
Rise Time
Fall Time
(20 to 80%)
(20 to 80%)
t
t
2
3
1.1
1.1
4.0
4.0
1.1
1.1
2.0
2.0
3.3
3.3
1.1
1.1
4.0
4.0
2+
3+
t
t
2
3
1.1
1.1
4.0
4.0
1.1
1.1
2.0
2.0
3.3
3.3
1.1
1.1
4.0
4.0
2–
3–
MOTOROLA
3–36
MC10109
ELECTRICAL CHARACTERISTICS (continued)
TEST VOLTAGE VALUES (Volts)
@ Test Temperature
V
V
ILmin
V
V
V
EE
IHmax
IHAmin
ILAmax
–30°C
+25°C
+85°C
–0.890
–0.810
–0.700
–1.890
–1.850
–1.825
–1.205
–1.105
–1.035
–1.500
–1.475
–1.440
–5.2
–5.2
–5.2
Pin
Under
Test
TEST VOLTAGE APPLIED TO PINS LISTED BELOW
(V
CC
)
Characteristic
Power Supply Drain Current
Input Current
Symbol
Gnd
V
V
ILmin
V
V
V
EE
IHmax
IHAmin
ILAmax
I
E
8
4
4
8
1, 16
1, 16
1, 16
I
4
8
8
inH
I
4
inL
Output Voltage
Logic 1
Logic 0
V
2
3
4
4
8
8
1, 16
1, 16
OH
Output Voltage
V
2
3
8
8
1, 16
1, 16
OL
Threshold Voltage
Threshold Voltage
Logic 1
V
2
3
4
4
8
8
1, 16
1, 16
OHA
4
4
Logic 0
V
2
3
8
8
1, 16
1, 16
OLA
Switching Times
(50Ω Load)
Pulse In
Pulse Out
–3.2 V
+2.0 V
Propagation Delay
t
t
t
t
2
2
3
3
4
4
4
4
2
2
3
3
8
8
8
8
1, 16
1, 16
1, 16
1, 16
4+2+
4–2–
4+3–
4–3+
Rise Time
Fall Time
(20 to 80%)
(20 to 80%)
t
t
2
3
4
4
2
3
8
8
1, 16
1, 16
2+
3+
t
t
2
3
4
4
2
3
8
8
1, 16
1, 16
2–
3–
Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.
Outputs are terminated through a 50–ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the
same manner.
3–37
MOTOROLA
MC10109
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 775–02
ISSUE C
M
S
S
0.007 (0.180)
T
L–M
N
B
Y BRK
–M–
–N–
M
S
S
0.007 (0.180)
T
L–M
N
U
D
D
–L–
Z
W
20
1
S
S
S
0.010 (0.250)
T
L–M
N
G1
X
V
VIEW D–D
M
M
S
S
S
S
A
R
0.007 (0.180)
0.007 (0.180)
T
L–M
L–M
N
N
Z
T
M
S
S
0.007 (0.180)
T
L–M
N
H
C
K1
E
K
0.004 (0.100)
–T– SEATING
G
J
PLANE
M
S
S
0.007 (0.180)
T
L–M
N
F
VIEW S
G1
VIEW S
S
S
S
0.010 (0.250)
T
L–M
N
NOTES:
1. DATUMS –L–, –M–, AND –N– DETERMINED
INCHES
MILLIMETERS
DIM
MIN
MAX
0.395
0.395
0.180
0.110
0.019
MIN
9.78
9.78
4.20
2.29
0.33
MAX
10.03
10.03
4.57
2.79
0.48
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
A
B
C
E
0.385
0.385
0.165
0.090
0.013
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
F
G
H
J
K
R
U
V
W
X
Y
0.050 BSC
1.27 BSC
0.026
0.020
0.025
0.350
0.350
0.042
0.042
0.042
–––
0.032
–––
–––
0.356
0.356
0.048
0.048
0.056
0.020
10
0.66
0.51
0.64
8.89
8.89
1.07
1.07
1.07
–––
2
0.81
–––
–––
9.04
9.04
1.21
1.21
1.42
0.50
10
Z
G1
K1
2
0.310
0.040
0.330
–––
7.88
1.02
8.38
–––
MOTOROLA
3–38
MC10109
OUTLINE DIMENSIONS
L SUFFIX
CERAMIC DIP PACKAGE
CASE 620–10
–A–
NOTES:
ISSUE V
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
16
1
9
8
–B–
C
L
INCHES
MILLIMETERS
DIM
A
B
C
D
MIN
MAX
0.785
0.295
0.200
0.020
MIN
19.05
6.10
–––
MAX
19.93
7.49
5.08
0.50
0.750
0.240
–––
–T–
SEATING
PLANE
0.015
0.39
K
N
E
0.050 BSC
1.27 BSC
F
0.055
0.065
1.40
1.65
G
H
K
L
M
N
0.100 BSC
2.54 BSC
M
E
0.008
0.125
0.015
0.170
0.21
3.18
0.38
4.31
F
J 16 PL
G
0.300 BSC
7.62 BSC
M
S
0.25 (0.010)
T B
0
15
0
15
D 16 PL
0.25 (0.010)
0.020
0.040
0.51
1.01
M
S
T
A
P SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08
ISSUE R
NOTES:
–A–
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
16
1
9
8
B
S
INCHES
MILLIMETERS
DIM
A
B
C
D
F
MIN
MAX
0.770
0.270
0.175
0.021
0.70
MIN
18.80
6.35
3.69
0.39
1.02
MAX
19.55
6.85
4.44
0.53
1.77
F
0.740
0.250
0.145
0.015
0.040
C
L
SEATING
–T–
G
H
J
K
L
0.100 BSC
0.050 BSC
2.54 BSC
1.27 BSC
PLANE
K
M
0.008
0.015
0.130
0.305
10
0.21
0.38
3.30
7.74
10
H
J
0.110
0.295
0
2.80
7.50
0
G
D 16 PL
0.25 (0.010)
M
S
0.020
0.040
0.51
1.01
M
M
T
A
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC10109/D
◊
相关型号：
©2020 ICPDF网 联系我们和版权申明