MC78L15ACPXA [ONSEMI]
线性电压稳压器,100 mA,5 至 24 V,正向;型号: | MC78L15ACPXA |
厂家: | ONSEMI |
描述: | 线性电压稳压器,100 mA,5 至 24 V,正向 输出元件 电源电路 线性稳压器IC 调节器 |
文件: | 总16页 (文件大小:126K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MC78L00A Series,
NCV78L00A
100 mA Positive Voltage
Regulators
The MC78L00A Series of positive voltage regulators are
inexpensive, easy−to−use devices suitable for a multitude of
applications that require a regulated supply of up to 100 mA. Like
their higher powered MC7800 and MC78M00 Series cousins, these
regulators feature internal current limiting and thermal shutdown
making them remarkably rugged. No external components are
required with the MC78L00 devices in many applications.
These devices offer a substantial performance advantage over the
traditional zener diode−resistor combination, as output impedance
and quiescent current are substantially reduced.
http://onsemi.com
TO−92
P SUFFIX
CASE 029
1
2
3
Features
• Wide Range of Available, Fixed Output Voltages
• Low Cost
Pin: 1. Output
2. Ground
3. Input
• Internal Short Circuit Current Limiting
• Internal Thermal Overload Protection
• No External Components Required
• Complementary Negative Regulators Offered (MC79L00A Series)
• Pb−Free Packages are Available
SOIC−8*
8
D SUFFIX
CASE 751
1
• NCV Prefix for Automotive and Other Applications Requiring Site
*SOIC−8 is an internally modified SO−8 package. Pins
2, 3, 6, and 7 are electrically common to the die attach
flag. This internal lead frame modification decreases
package thermal resistance and increases power
dissipationcapability when appropriately mounted on
a printed circuit board. SOIC−8 conforms to all exter-
nal dimensions of the standard SO−8 package.
and Control Changes
Input
Q11
Q3
Q5
15k
Q12
Q1
3.8k
Q10
5.0k
3.0
Output
PIN CONNECTIONS
Q4
Q6
0−25k
1
2
3
4
8
7
6
5
V
V
IN
OUT
GND
GND
NC
GND
GND
1.9k
19k
2.2k
1.2k
420
Q9
C
NC
Q8
Q2
Z1
2.85k
(Top View)
Q7
1.0k
ORDERING INFORMATION
Ground
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
Figure 1. Representative Schematic Diagram
DEVICE MARKING INFORMATION
MC78LXXA
Input
Output
See general marking information in the device marking
section on page 14 of this data sheet.
C *
in
0.33mF
C **
O
Figure 2. Standard Application
A common ground is required between the input and the output voltages. The
input voltage must remain typically 2.0 V above the output voltage even during
the low point on the input ripple voltage.
*C is required if regulator is located an appreciable distance from power
in
supply filter.
** C is not needed for stability; however, it does improve transient response.
O
©
Semiconductor Components Industries, LLC, 2005
1
Publication Order Number:
May, 2005 − Rev. 10
MC78L00A/D
MC78L00A Series, NCV78L00A
MAXIMUM RATINGS (T = +125°C, unless otherwise noted.)
A
Rating
Symbol
Value
Unit
Input Voltage (2.6 V−8.0 V)
Input Voltage (12 V−18 V)
Input Voltage (24 V)
V
I
30
35
40
Vdc
Storage Temperature Range
T
−65 to +150
0 to +150
°C
°C
stg
Operating Junction Temperature Range
T
J
Maximumratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values
(not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage
may occur and reliability may be affected.
ELECTRICAL CHARACTERISTICS (V = 10 V, I = 40 mA, C = 0.33 mF, C = 0.1 mF, − 40°C < T < +125°C (for MC78LXXAB,
I
O
I
O
J
NCV78L05A), 0°C < T < +125°C (for MC78LXXAC), unless otherwise noted.)
J
MC78L05AC, AB, NCV78L05A
Characteristics
Output Voltage (T = +25°C)
Symbol
Min
Typ
Max
Unit
Vdc
mV
V
O
4.8
5.0
5.2
J
Line Regulation
(T = +25°C, I = 40 mA)
Reg
line
J
O
7.0 Vdc ≤ V ≤ 20 Vdc
−
−
55
45
150
100
I
8.0 Vdc ≤ V ≤ 20 Vdc
I
Load Regulation
Reg
mV
Vdc
mA
mA
load
(T = +25°C, 1.0 mA ≤ I ≤ 100 mA)
−
−
11
5.0
60
30
J
O
(T = +25°C, 1.0 mA ≤ I ≤ 40 mA)
J
O
Output Voltage
V
O
(7.0 Vdc ≤ V ≤ 20 Vdc, 1.0 mA ≤ I ≤ 40 mA)
4.75
4.75
−
−
5.25
5.25
I
O
(V = 10 V, 1.0 mA ≤ I ≤ 70 mA)
I
O
Input Bias Current
I
IB
(T = +25°C)
−
−
3.8
−
6.0
5.5
J
(T = +125°C)
J
Input Bias Current Change
DI
IB
(8.0 Vdc ≤ V ≤ 20 Vdc)
−
−
−
−
1.5
0.1
I
(1.0 mA ≤ I ≤ 40 mA)
O
Output Noise Voltage
V
−
41
−
40
−
−
−
mV
dB
n
(T = +25°C, 10 Hz ≤ f ≤ 100 kHz)
A
Ripple Rejection (I = 40 mA,
RR
49
O
f = 120 Hz, 8.0 Vdc ≤ V ≤ 18 V, T = +25°C)
I
J
Dropout Voltage (T = +25°C)
V − V
1.7
Vdc
J
I
O
NOTE: NCV78L05A: T = −40°C, T
= +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring
low
high
site and change control.
http://onsemi.com
2
MC78L00A Series, NCV78L00A
ELECTRICAL CHARACTERISTICS (V = 14 V, I = 40 mA, C = 0.33 mF, C = 0.1 mF, − 40°C < T < +125°C (for MC78LXXAB),
I
O
I
O
J
0°C < T < +125°C (for MC78LXXAC), unless otherwise noted.)
J
MC78L08AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Vdc
mV
Output Voltage (T = +25°C)
V
O
7.7
8.0
8.3
J
Line Regulation
Reg
line
(T = +25°C, I = 40 mA)
J
O
10.5 Vdc ≤ V ≤ 23 Vdc
−
−
20
12
175
125
I
11 Vdc ≤ V ≤ 23 Vdc
I
Load Regulation
Reg
mV
Vdc
mA
mA
load
(T = +25°C, 1.0 mA ≤ I ≤ 100 mA)
−
−
15
8.0
80
40
J
O
(T = +25°C, 1.0 mA ≤ I ≤ 40 mA)
J
O
Output Voltage
V
O
(10.5 Vdc ≤ V ≤ 23 Vdc, 1.0 mA ≤ I ≤ 40 mA)
7.6
7.6
−
−
8.4
8.4
I
O
(V = 14 V, 1.0 mA ≤ I ≤ 70 mA)
I
O
Input Bias Current
I
IB
(T = +25°C)
−
−
3.0
−
6.0
5.5
J
(T = +125°C)
J
Input Bias Current Change
DI
IB
(11 Vdc ≤ V ≤ 23 Vdc)
−
−
−
−
1.5
0.1
I
(1.0 mA ≤ I ≤ 40 mA)
O
Output Noise Voltage
(T = +25°C, 10 Hz ≤ f ≤ 100 kHz)
A
V
−
37
−
60
−
−
−
mV
dB
n
Ripple Rejection (I = 40 mA,
RR
57
O
f = 120 Hz, 12 V ≤ V ≤ 23 V, T = +25°C)
I
J
Dropout Voltage (T = +25°C)
V − V
1.7
Vdc
J
I
O
ELECTRICAL CHARACTERISTICS (V = 15 V, I = 40 mA, C = 0.33 mF, C = 0.1 mF, − 40°C < T < +125°C (for MC78LXXAB),
I
O
I
O
J
0°C < T < +125°C (for MC78LXXAC), unless otherwise noted.)
J
MC78L09AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Vdc
mV
Output Voltage (T = +25°C)
V
O
8.6
9.0
9.4
J
Line Regulation
Reg
line
(T = +25°C, I = 40 mA)
J
O
11.5 Vdc ≤ V ≤ 24 Vdc
−
−
20
12
175
125
I
12 Vdc ≤ V ≤ 24 Vdc
I
Load Regulation
Reg
mV
Vdc
mA
mA
load
(T = +25°C, 1.0 mA ≤ I ≤ 100 mA)
−
−
15
8.0
90
40
J
O
(T = +25°C, 1.0 mA ≤ I ≤ 40 mA)
J
O
Output Voltage
V
O
(11.5 Vdc ≤ V ≤ 24 Vdc, 1.0 mA ≤ I ≤ 40 mA)
8.5
8.5
−
−
9.5
9.5
I
O
(V = 15 V, 1.0 mA ≤ I ≤ 70 mA)
I
O
Input Bias Current
I
IB
(T = +25°C)
−
−
3.0
−
6.0
5.5
J
(T = +125°C)
J
Input Bias Current Change
DI
IB
(11 Vdc ≤ V ≤ 23 Vdc)
−
−
−
−
1.5
0.1
I
(1.0 mA ≤ I ≤ 40 mA)
O
Output Noise Voltage
(T = +25°C, 10 Hz ≤ f ≤ 100 kHz)
A
V
−
37
−
60
−
−
−
mV
dB
n
Ripple Rejection (I = 40 mA,
RR
57
O
f = 120 Hz, 13 V ≤ V ≤ 24 V, T = +25°C)
I
J
Dropout Voltage
V − V
1.7
Vdc
I
O
(T = +25°C)
J
http://onsemi.com
3
MC78L00A Series, NCV78L00A
ELECTRICAL CHARACTERISTICS (V = 19 V, I = 40 mA, C = 0.33 mF, C = 0.1 mF, − 40°C < T < +125°C (for MC78LXXAB),
I
O
I
O
J
0°C < T < +125°C (for MC78LXXAC), unless otherwise noted.)
J
MC78L12AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Vdc
mV
Output Voltage (T = +25°C)
V
O
11.5
12
12.5
J
Line Regulation
Reg
line
(T = +25°C, I = 40 mA)
J
O
14.5 Vdc ≤ V ≤ 27 Vdc
−
−
120
100
250
200
I
16 Vdc ≤ V ≤ 27 Vdc
I
Load Regulation
Reg
mV
Vdc
mA
mA
load
(T = +25°C, 1.0 mA ≤ I ≤ 100 mA)
−
−
20
10
100
50
J
O
(T = +25°C, 1.0 mA ≤ I ≤ 40 mA)
J
O
Output Voltage
V
O
(14.5 Vdc ≤ V ≤ 27 Vdc, 1.0 mA ≤ I ≤ 40 mA)
11.4
11.4
−
−
12.6
12.6
I
O
(V = 19 V, 1.0 mA ≤ I ≤ 70 mA)
I
O
Input Bias Current
I
IB
(T = +25°C)
−
−
4.2
−
6.5
6.0
J
(T = +125°C)
J
Input Bias Current Change
DI
IB
(16 Vdc ≤ V ≤ 27 Vdc)
−
−
−
−
1.5
0.1
I
(1.0 mA ≤ I ≤ 40 mA)
O
Output Noise Voltage
(T = +25°C, 10 Hz ≤ f ≤ 100 kHz)
A
V
−
37
−
80
−
−
−
mV
dB
n
Ripple Rejection (I = 40 mA,
RR
42
O
f = 120 Hz, 15 V ≤ V ≤ 25 V, T = +25°C)
I
J
Dropout Voltage
V − V
1.7
Vdc
I
O
(T = +25°C)
J
ELECTRICAL CHARACTERISTICS (V = 23 V, I = 40 mA, C = 0.33 mF, C = 0.1 mF, − 40°C < T < +125°C (for MC78LXXAB),
I
O
I
O
J
S 0°C < T < +125°C (for MC78LXXAC), unless otherwise noted.)
J
MC78L15AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (T = +25°C)
V
14.4
15
15.6
Vdc
mV
J
O
Line Regulation
Reg
line
(T = +25°C, I = 40 mA)
J
O
17.5 Vdc ≤ V ≤ 30 Vdc
−
−
130
110
300
250
I
20 Vdc ≤ V ≤ 30 Vdc
I
Load Regulation
Reg
mV
Vdc
mA
mA
load
(T = +25°C, 1.0 mA ≤ I ≤ 100 mA)
−
−
25
12
150
75
J
O
(T = +25°C, 1.0 mA ≤ I ≤ 40 mA)
J
O
Output Voltage
V
O
(17.5 Vdc ≤ V ≤ 30 Vdc, 1.0 mA ≤ I ≤ 40 mA)
14.25
14.25
−
−
15.75
15.75
I
O
(V = 23 V, 1.0 mA ≤ I ≤ 70 mA)
I
O
Input Bias Current
I
IB
(T = +25°C)
−
−
4.4
−
6.5
6.0
J
(T = +125°C)
J
Input Bias Current Change
DI
IB
(20 Vdc ≤ V ≤ 30 Vdc)
−
−
−
−
1.5
0.1
I
(1.0 mA ≤ I ≤ 40 mA)
O
Output Noise Voltage
(T = +25°C, 10 Hz ≤ f ≤ 100 kHz)
A
V
−
34
−
90
−
−
−
mV
dB
n
Ripple Rejection (I = 40 mA,
RR
V − V
39
O
f = 120 Hz, 18.5 V ≤ V ≤ 28.5 V, T = +25°C)
I
J
Dropout Voltage
1.7
Vdc
I
O
(T = +25°C)
J
http://onsemi.com
4
MC78L00A Series, NCV78L00A
ELECTRICAL CHARACTERISTICS (V = 27 V, I = 40 mA, C = 0.33 mF, C = 0.1 mF, 0°C < T < +125°C, unless otherwise noted.)
I
O
I
O
J
MC78L18AC
Characteristics
Output Voltage (T = +25°C)
Symbol
Min
Typ
Max
Unit
V
O
17.3
18
18.7
Vdc
J
Line Regulation
(T = +25°C, I = 40 mA)
J
O
21.4 Vdc ≤ V ≤ 33 Vdc
I
Reg
mV
line
20.7 Vdc ≤ V ≤ 33 Vdc
−
−
45
35
325
275
I
22 Vdc ≤ V ≤ 33 Vdc
I
21 Vdc ≤ V ≤ 33 Vdc
I
Load Regulation
Reg
mV
load
(T = +25°C, 1.0 mA ≤ I ≤ 100 mA)
−
−
30
15
170
85
J
O
(T = +25°C, 1.0 mA ≤ I ≤ 40 mA)
J
O
Output Voltage
V
O
Vdc
(21.4 Vdc ≤ V ≤ 33 Vdc, 1.0 mA ≤ I ≤ 40 mA)
I
O
(20.7 Vdc ≤ V ≤ 33 Vdc, 1.0 mA ≤ I ≤ 40 mA)
17.1
17.1
−
−
18.9
18.9
I
O
(V = 27 V, 1.0 mA ≤ I ≤ 70 mA)
I
O
(V = 27 V, 1.0 mA ≤ I ≤ 70 mA)
I
O
Input Bias Current
I
mA
mA
IB
(T = +25°C)
−
−
3.1
−
6.5
6.0
J
(T = +125°C)
J
Input Bias Current Change
DI
IB
(22 Vdc ≤ V ≤ 33 Vdc)
I
(21 Vdc ≤ V ≤ 33 Vdc)
−
−
−
−
1.5
0.1
I
(1.0 mA ≤ I ≤ 40 mA)
O
Output Noise Voltage
(T = +25°C, 10 Hz ≤ f ≤ 100 kHz)
A
V
−
33
−
150
−
−
−
mV
dB
n
Ripple Rejection (I = 40 mA,
RR
V − V
48
O
f = 120 Hz, 23 V ≤ V ≤ 33 V, T = +25°C)
I
J
Dropout Voltage
1.7
Vdc
I
O
(T = +25°C)
J
http://onsemi.com
5
MC78L00A Series, NCV78L00A
ELECTRICAL CHARACTERISTICS (V = 33 V, I = 40 mA, C = 0.33 mF, C = 0.1 mF, 0°C < T < +125°C, unless otherwise noted.)
I
O
I
O
J
MC78L24AC
Characteristics
Output Voltage (T = +25°C)
Symbol
Min
Typ
Max
Unit
Vdc
mV
V
O
23
24
25
J
Line Regulation
(T = +25°C, I = 40 mA)
Reg
line
J
O
27.5 Vdc ≤ V ≤ 38 Vdc
−
−
−
−
50
60
−
300
350
I
28 Vdc ≤ V ≤ 80 Vdc
I
27 Vdc ≤ V ≤ 38 Vdc
I
Load Regulation
Reg
mV
load
(T = +25°C, 1.0 mA ≤ I ≤ 100 mA)
−
−
40
20
200
100
J
O
(T = +25°C, 1.0 mA ≤ I ≤ 40 mA)
J
O
Output Voltage
V
O
Vdc
(28 Vdc ≤ V ≤ 38 Vdc, 1.0 mA ≤ I ≤ 40 mA)
I
O
(27 Vdc ≤ V ≤ 38 Vdc, 1.0 mA ≤ I ≤ 40 mA)
22.8
22.8
−
−
25.2
25.2
I
O
(28 Vdc ≤ V 33 Vdc, 1.0 mA ≤ I ≤ 70 mA)
I =
O
(27 Vdc ≤ V ≤ 33 Vdc, 1.0 mA ≤ I ≤ 70 mA)
I
O
Input Bias Current
I
mA
mA
IB
(T = +25°C)
−
−
3.1
−
6.5
6.0
J
(T = +125°C)
J
Input Bias Current Change
DI
IB
(28 Vdc ≤ V ≤ 38 Vdc)
−
−
−
−
1.5
0.1
I
(1.0 mA ≤ I ≤ 40 mA)
O
Output Noise Voltage
(T = +25°C, 10 Hz ≤ f ≤ 100 kHz)
A
V
−
31
−
200
−
−
−
mV
dB
n
Ripple Rejection (I = 40 mA,
RR
V − V
45
O
f = 120 Hz, 29 V ≤ V ≤ 35 V, T = +25°C)
I
J
Dropout Voltage
1.7
Vdc
I
O
(T = +25°C)
J
http://onsemi.com
6
MC78L00A Series, NCV78L00A
8.0
2.5
2.0
1.5
MC78L05AC
= 5.0 V
T = 25°C
J
I
= 70 mA
O
V
out
6.0
4.0
2.0
0
I
= 1.0 mA
O
I
= 40 mA
O
1.0
0.5
0
I
= 1.0 mA
O
I
= 40 mA
I
= 100 mA
O
O
Dropout of Regulation is
defined as when
ꢀꢀꢀꢀV = 2% of V
O
O
0
2.0
4.0
6.0
8.0
10
0
25
50
75
100
125
V , INPUT VOLTAGE (V)
I
T , JUNCTION TEMPERATURE (°C)
J
Figure 3. Dropout Characteristics
Figure 4. Dropout Voltage versus
Junction Temperature
4.2
4.0
3.8
3.6
3.4
3.2
3.0
0
5.0
4.0
3.0
2.0
1.0
0
MC78L05AC
V
= 5.0 V
= 40 mA
out
I
O
T = 25°C
J
MC78L05AC
V = 10 V
I
V = 5.0 V
O
I
= 40 mA
O
0
25
50
75
100
125
0
5.0
10
15
20
25
30
35
40
T , AMBIENT TEMPERATURE (°C)
A
V , INPUT VOLTAGE (V)
I
Figure 5. Input Bias Current versus
Ambient Temperature
Figure 6. Input Bias Current
versus Input Voltage
170
150
130
110
90
3.2
2.8
10,000
1000
P
for T = 50°C
A
D(max)
No Heatsink
2.4
2.0
1.6
1.2
0.8
0.4
Graph represents symmetrical layout
2.0 oz.
L
Copper
100
10
70
L
3.0 mm
R
P
= 200°C/W
D(max)
q
JA
50
to 25°C = 625 mW
R
q
JA
30
0
10
20
30
40
50
25
50
75
100
125
150
T , AMBIENT TEMPERATURE (°C)
A
L, LENGTH OF COPPER (mm)
Figure 7. Maximum Average Power Dissipation versus
Ambient Temperature − TO−92 Type Package
Figure 8. SOIC−8 Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
http://onsemi.com
7
MC78L00A Series, NCV78L00A
APPLICATIONS INFORMATION
Design Considerations
input bypass capacitor should be selected to provide good
high−frequency characteristics to insure stable operation
under all load conditions. A 0.33 mF or larger tantalum,
mylar, or other capacitor having low internal impedance at
high frequencies should be chosen. The bypass capacitor
should be mounted with the shortest possible leads directly
across the regulators input terminals. Good construction
techniques should be used to minimize ground loops and
lead resistance drops since the regulator has no external
sense lead. Bypassing the output is also recommended.
The MC78L00A Series of fixed voltage regulators are
designed with Thermal Overload Protection that shuts
down the circuit when subjected to an excessive power
overload condition. Internal Short Circuit Protection limits
the maximum current the circuit will pass.
In many low current applications, compensation
capacitors are not required. However, it is recommended
that the regulator input be bypassed with a capacitor if the
regulator is connected to the power supply filter with long
wire lengths, or if the output load capacitance is large. The
+20V
MC78L15A
+V
O
0.33mF
10k
7
2
3
MC78L05A
Input
−
6
MC1741
R
0.33mF
Constant
Current to
Grounded Load
+
4
10k
I
0.33mF
20V
O
MPS A70
6.5
−V
O
MPS U55
The MC78L00 regulators can also be used as a current source
when connected as above. In order to minimize dissipation the
MC78L05C is chosen in this application. Resistor R determines
the current as follows:
Figure 10. 15 V Tracking Voltage Regulator
5.0 V
R
I
=
+ I
B
O
+V
I
MC78LXXA
MC79LXXA
+V
O
0.33mF
0.1mF
0.1mF
I
= 3.8 mA over line and load changes
IB
−V
I
For example, a 100 mA current source would require R to be a
50ꢁW, 1/2 W resistor and the output voltage compliance would be
the input voltage less 7 V.
0.33mF
−V
O
Figure 9. Current Regulator
Figure 11. Positive and Negative Regulator
http://onsemi.com
8
MC78L00A Series, NCV78L00A
ORDERING INFORMATION
Operating
Temperature Range
†
Device
MC78L05ABD
Output Voltage
Package
SOIC−8
SOIC−8
SOIC−8
Shipping
98 Units/Rail
98 Units/Rail
MC78L05ABDG
MC78L05ABDR2
MC78L05ABDR2G
2500 Tape & Reel
2500 Tape & Reel
SOIC−8
(Pb−Free)
NCV78L05ABDR2*
NCV78L05ABDR2G*
SOIC−8
2500 Tape & Reel
2500 Tape & Reel
SOIC−8
(Pb−Free)
MC78L05ABP
TO−92
2000 Units/Bag
2000 Units/Bag
MC78L05ABPG
TO−92
(Pb−Free)
T = −40° to +125°C
J
MC78L05ABPRA
TO−92
2000 Tape & Reel
2000 Tape & Reel
MC78L05ABPRAG
TO−92
(Pb−Free)
MC78L05ABPRE
TO−92
2000 Tape & Reel
2000 Tape & Reel
MC78L05ABPREG
TO−92
(Pb−Free)
MC78L05ABPRM
MC78L05ABPRMG
TO−92
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
5.0 V
MC78L05ACD
SOIC−8
98 Units/Rail
98 Units/Rail
MC78L05ACDG
SOIC−8
(Pb−Free)
MC78L05ACDR2
SOIC−8
2500 Tape & Reel
2500 Tape & Reel
MC78L05ACDR2G
SOIC−8
(Pb−Free)
MC78L05ACP
TO−92
2000 Units/Bag
2000 Units/Bag
MC78L05ACPG
TO−92
(Pb−Free)
MC78L05ACPRA
MC78L05ACPRAG
TO−92
2000 Tape & Reel
2000 Tape & Reel
T = 0° to +125°C
J
TO−92
(Pb−Free)
MC78L05ACPRE
MC78L05ACPREG
TO−92
2000 Tape & Reel
2000 Tape & Reel
TO−92
(Pb−Free)
MC78L05ACPRM
MC78L05ACPRMG
TO−92
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
MC78L05ACPRP
MC78L05ACPRPG
TO−92
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
*NCV78L05A: T = −40°C, T
= +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
low
high
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
9
MC78L00A Series, NCV78L00A
ORDERING INFORMATION (continued)
Operating
Temperature Range
†
Device
MC78L08ABD
Output Voltage
Package
Shipping
SOIC−8
98 Units/Rail
98 Units/Rail
SOIC−8
MC78L08ABDG
(Pb−Free)
SOIC−8
MC78L08ABDR2
2500 Tape & Reel
2500 Tape & Reel
SOIC−8
MC78L08ABDR2G
(Pb−Free)
TO−92
MC78L08ABP
2000 Units/Bag
2000 Units/Bag
T = −40° to +125°C
J
TO−92
MC78L08ABPG
(Pb−Free)
TO−92
MC78L08ABPRA
2000 Tape & Reel
2000 Tape & Reel
TO−92
MC78L08ABPRAG
(Pb−Free)
TO−92
MC78L08ABPRP
2000 Ammo Pack
2000 Ammo Pack
TO−92
MC78L08ABPRPG
(Pb−Free)
SOIC−8
MC78L08ACD
98 Units/Rail
98 Units/Rail
8.0 V
SOIC−8
MC78L08ACDG
(Pb−Free)
SOIC−8
MC78L08ACDR2
2500 Tape & Reel
2500 Tape & Reel
SOIC−8
MC78L08ACDR2G
(Pb−Free)
TO−92
MC78L08ACP
2000 Units/Bag
2000 Units/Bag
TO−92
MC78L08ACPG
(Pb−Free)
T = 0° to +125°C
J
TO−92
MC78L08ACPRA
MC78L08ACPRAG
2000 Tape & Reel
2000 Tape & Reel
TO−92
(Pb−Free)
TO−92
MC78L08ACPRE
MC78L08ACPREG
2000 Tape & Reel
2000 Tape & Reel
TO−92
(Pb−Free)
TO−92
MC78L08ACPRP
MC78L08ACPRPG
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
SOIC−8
MC78L09ABD
98 Units/Rail
98 Units/Rail
SOIC−8
MC78L09ABDG
(Pb−Free)
SOIC−8
MC78L09ABDR2
2500 Tape & Reel
2500 Tape & Reel
SOIC−8
MC78L09ABDR2G
(Pb−Free)
9.0 V
T = −40° to +125°C
J
TO−92
MC78L09ABPRA
2000 Tape & Reel
2000 Tape & Reel
TO−92
MC78L09ABPRAG
(Pb−Free)
TO−92
MC78L09ABPRP
2000 Ammo Pack
2000 Ammo Pack
MC78L09ABPRPG
TO−92
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
MC78L00A Series, NCV78L00A
ORDERING INFORMATION (continued)
Operating
Temperature Range
†
Device
MC78L09ACD
Output Voltage
Package
Shipping
SOIC−8
98 Units/Rail
98 Units/Rail
SOIC−8
MC78L09ACDG
(Pb−Free)
SOIC−8
MC78L09ACDR2
2500 Tape & Reel
2500 Tape & Reel
9.0 V
T = 0° to +125°C
J
SOIC−8
MC78L09ACDR2G
(Pb−Free)
TO−92
MC78L09ACP
2000 Units/Bag
2000 Units/Bag
TO−92
MC78L09ACPG
(Pb−Free)
SOIC−8
MC78L12ABD
98 Units/Rail
98 Units/Rail
SOIC−8
MC78L12ABDG
(Pb−Free)
SOIC−8
MC78L12ABDR2
2500 Tape & Reel
2500 Tape & Reel
SOIC−8
MC78L12ABDR2G
(Pb−Free)
TO−92
MC78L12ABP
2000 Units/Bag
2000 Units/Bag
T = −40° to +125°C
J
TO−92
MC78L12ABPG
(Pb−Free)
TO−92
MC78L12ABPRP
2000 Ammo Pack
2000 Ammo Pack
TO−92
MC78L12ABPRPG
(Pb−Free)
NCV78L12ABDR2*
NCV78L12ABDR2G*
SOIC−8
2500 Tape & Reel
2500 Tape & Reel
SOIC−8
(Pb−Free)
SOIC−8
MC78L12ACD
98 Units/Rail
98 Units/Rail
SOIC−8
MC78L12ACDG
(Pb−Free)
12 V
SOIC−8
MC78L12ACDR2
2500 Tape & Reel
2500 Tape & Reel
SOIC−8
MC78L12ACDR2G
(Pb−Free)
TO−92
MC78L12ACP
2000 Units/Bag
2000 Units/Bag
TO−92
MC78L12ACPG
(Pb−Free)
TO−92
MC78L12ACPRA
MC78L12ACPRAG
2000 Tape & Reel
2000 Tape & Reel
T = 0° to +125°C
J
TO−92
(Pb−Free)
TO−92
MC78L12ACPRE
MC78L12ACPREG
2000 Tape & Reel
2000 Tape & Reel
TO−92
(Pb−Free)
TO−92
MC78L12ACPRM
MC78L12ACPRMG
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
TO−92
MC78L12ACPRP
MC78L12ACPRPG
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
*NCV78L12A: T = −40°C, T
= +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
low
high
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
11
MC78L00A Series, NCV78L00A
ORDERING INFORMATION (continued)
Operating
Temperature Range
†
Device
MC78L15ABD
Output Voltage
Package
Shipping
SOIC−8
98 Units/Rail
98 Units/Rail
MC78L15ABDG
SOIC−8
(Pb−Free)
MC78L15ABDR2
SOIC−8
2500 Tape & Reel
2500 Tape & Reel
MC78L15ABDR2G
SOIC−8
(Pb−Free)
MC78L15ABP
TO−92
2000 Units/Bag
2000 Units/Bag
T = −40° to +125°C
J
MC78L15ABPG
TO−92
(Pb−Free)
MC78L15ABPRA
TO−92
2000 Tape & Reel
2000 Tape & Reel
MC78L15ABPRAG
TO−92
(Pb−Free)
MC78L15ABPRP
TO−92
2000 Ammo Pack
2000 Ammo Pack
MC78L15ABPRPG
TO−92
(Pb−Free)
15 V
MC78L15ACD
SOIC−8
98 Units/Rail
98 Units/Rail
MC78L15ACDG
SOIC−8
(Pb−Free)
MC78L15ACDR2
SOIC−8
2500 Tape & Reel
2500 Tape & Reel
MC78L15ACDR2G
SOIC−8
(Pb−Free)
MC78L15ACP
TO−92
2000 Units/Bag
2000 Units/Bag
T = 0° to +125°C
J
MC78L15ACPG
TO−92
(Pb−Free)
MC78L15ACPRA
MC78L15ACPRAG
TO−92
2000 Tape & Reel
2000 Tape & Reel
TO−92
(Pb−Free)
MC78L15ACPRP
MC78L15ACPRPG
TO−92
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
12
MC78L00A Series, NCV78L00A
ORDERING INFORMATION (continued)
Operating
Temperature Range
†
Device
MC78L18ABP
Output Voltage
Package
Shipping
TO−92
2000 Units/Bag
2000 Units/Bag
T = −40° to +125°C
J
MC78L18ABPG
TO−92
(Pb−Free)
MC78L18ACP
TO−92
2000 Units/Bag
2000 Units/Bag
MC78L18ACPG
TO−92
(Pb−Free)
MC78L18ACPRA
MC78L18ACPRAG
TO−92
2000 Tape & Reel
2000 Tape & Reel
18 V
TO−92
(Pb−Free)
T = 0° to +125°C
J
MC78L18ACPRM
MC78L18ACPRMG
TO−92
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
MC78L18ACPRP
MC78L18ACPRPG
TO−92
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
MC78L24ABP
TO−92
2000 Units/Bag
2000 Units/Bag
T = −40° to +125°C
J
MC78L24ABPG
TO−92
(Pb−Free)
MC78L24ACP
TO−92
2000 Units/Bag
2000 Units/Bag
MC78L24ACPG
TO−92
(Pb−Free)
24 V
MC78L24ACPRA
MC78L24ACPRAG
TO−92
2000 Tape & Reel
2000 Tape & Reel
T = 0° to +125°C
J
TO−92
(Pb−Free)
MC78L24ACPRP
MC78L24ACPRPG
TO−92
2000 Ammo Pack
2000 Ammo Pack
TO−92
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
13
MC78L00A Series, NCV78L00A
MARKING DIAGRAMS
SOIC−8
D SUFFIX
CASE 751
8
1
8
8LxxA
ALYWB
G
8LxxA
ALYWC
G
1
xx = 05, 08, 09, 12, or 15
A
L
= Assembly Location
= Wafer Lot
Y
W
= Year
= Work Week
B, C = Temperature Range
G
= Pb−Free Package
TO−92
P SUFFIX
CASE 029
MC78L
zzABP
MC78L
zzACP
ALYWWG
G
ALYWWG
G
1
2 3
1 2 3
zz
A
L
= 05, 08, 09, 12, 15, 18 or 24
= Assembly Location
= Wafer Lot
Y
= Year
WW = Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
http://onsemi.com
14
MC78L00A Series, NCV78L00A
PACKAGE DIMENSIONS
SOIC−8 NB
D SUFFIX
CASE 751−07
ISSUE AF
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
−X−
A
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
8
5
4
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
S
M
M
B
0.25 (0.010)
Y
1
K
−Y−
G
MILLIMETERS
DIM MIN MAX
INCHES
MIN
MAX
0.197
0.157
0.069
0.020
A
B
C
D
G
H
J
K
M
N
S
4.80
3.80
1.35
0.33
5.00 0.189
4.00 0.150
1.75 0.053
0.51 0.013
C
N X 45
_
SEATING
PLANE
−Z−
1.27 BSC
0.050 BSC
0.10 (0.004)
0.10
0.19
0.40
0
0.25 0.004
0.25 0.007
1.27 0.016
0.010
0.010
0.050
8
0.020
0.244
M
J
H
D
8
0
_
_
_
_
0.25
5.80
0.50 0.010
6.20 0.228
M
S
S
X
0.25 (0.010)
Z
Y
SOLDERING FOOTPRINT*
1.52
0.060
7.0
4.0
0.275
0.155
0.6
0.024
1.270
0.050
mm
inches
ǒ
Ǔ
SCALE 6:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
MountingTechniques Reference Manual, SOLDERRM/D.
http://onsemi.com
15
MC78L00A Series, NCV78L00A
PACKAGE DIMENSIONS
TO−92 (TO−226)
P SUFFIX
CASE 29−11
ISSUE AL
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
A
B
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
BEYOND DIMENSION K MINIMUM.
R
P
L
INCHES
DIM MIN MAX
MILLIMETERS
SEATING
PLANE
K
MIN
4.45
4.32
3.18
0.407
1.15
2.42
0.39
12.70
6.35
2.04
−−−
MAX
5.20
5.33
4.19
0.533
1.39
2.66
0.50
−−−
A
B
C
D
G
H
J
0.175
0.170
0.125
0.016
0.045
0.095
0.015
0.500
0.250
0.080
−−−
0.205
0.210
0.165
0.021
0.055
0.105
0.020
−−−
D
X X
G
J
H
V
K
L
−−−
−−−
C
N
P
R
V
0.105
0.100
−−−
2.66
2.54
−−−
SECTION X−X
0.115
0.135
2.93
3.43
1
N
−−−
−−−
N
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
For additional information, please contact your
local Sales Representative.
MC78L00A/D
相关型号:
©2020 ICPDF网 联系我们和版权申明