MID400TVM [ONSEMI]
8-Pin DIP AC Line Monitor Logic Output Optocoupler;型号: | MID400TVM |
厂家: | ONSEMI |
描述: | 8-Pin DIP AC Line Monitor Logic Output Optocoupler |
文件: | 总14页 (文件大小:220K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
www.onsemi.com
AC Line Monitor Logic-Out
Device
PDIP8 6.6x3.81, 2.54P
CASE 646BW
8
1
MID400M
PDIP8 9.655x6.6, 2.54P
CASE 646CQ
8
8
Description
1
1
The MID400M is an optically isolated AC line−to−logic interface
device. It is packaged in an 8−lead plastic DIP. The AC line voltage is
monitored by two back−to−back GaAs LED diodes in series with an
external resistor. A high gain detector circuit senses the LED current
and drives the output gate to a logic low condition.
The MID400M has been designed solely for the use as an AC line
monitor. It is recommended for use in any AC−to−DC control
application where excellent optical isolation, solid state reliability,
TTL compatibility, small size, low power, and low frequency
operations are required.
PDIP8 GW
CASE 709AC
MARKING DIAGRAM
ON
MID400
VXXYYB
Features
MID400 = Specific Device Code
• Direct Operation from any Line Voltage with the Use of an External
V
= DIN EN/IEC60747−5−5 Option (only
appears on component ordered with
this option)
Resistor
• Externally Adjustable Time Delay
XX
YY
= Two−Digit Year Code, e.g., “06”
= Digit Work Week, Ranging from “01”
to “53”
• Externally Adjustable AC Voltage Sensing Level
• Logic Level Compatibility
B
= Assembly Package Code
• Safety and Regulatory Approvals:
♦ UL1577, 5,000 VAC
for 1 Minute
RMS
FUNCTIONAL SCHEMATIC
♦ DIN−EN/IEC60747−5−5, 890 V Peak Working Insulation Voltage
Applications
• Monitoring of the AC/DC “Line−down” Condition
1
2
3
4
8
7
6
5
VCC
AUX
VO
• “Closed−loop” Interface between Electromechanical Elements such
as Solenoids, Relay Contacts, Small Motors, and Microprocessors
• Time Delay Isolation Switch
N/C
N/C
GND
ORDERING INFORMATION
See detailed ordering and shipping information on page 10 of
this data sheet.
© Semiconductor Components Industries, LLC, 2020
1
Publication Order Number:
May, 2022 − Rev. 0
MID400M/D
MID400M
SAFETY AND INSULATION RATINGS (As per DIN EN/IEC 60747−5−5, this optocoupler is suitable for “safe electrical insulation”
only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits.)
Parameter
Characteristics
Installation Classifications per DIN VDE 0110/1.89 Table 1, For Rated Mains Voltage <150 V
I–IV
I–IV
RMS
RMS
RMS
RMS
<300 V
<450 V
I–III
<600 V
I–III
Climatic Classification
40/100/21
2
Pollution Degree (DIN VDE 0110/1.89)
Comparative Tracking Index
175
Symbol
Parameter
Value
Unit
V
PR
Input−to−Output Test Voltage, Method A, V
x 1.6 = V , Type and Sample Test
1,335
V
peak
IORM
PR
with t = 10 s, Partial Discharge < 5 pC
m
Input−to−Output Test Voltage, Method B, V
x 1.875 = V , 100% Production Test
1,669
V
peak
IORM
PR
with t = 1 s, Partial Discharge < 5 pC
m
V
Maximum Working Insulation Voltage
Highest Allowable Over−Voltage
External Creepage
890
6,000
≥8.0
≥7.4
≥10.16
≥0.5
150
V
V
IORM
peak
V
IOTM
peak
mm
mm
mm
mm
°C
External Clearance
External Clearance (for Option TV, 0.4” Lead Spacing)
Distance Through Insulation (Insulation Thickness)
Case Temperature (Note 1)
DTI
T
S
I
Input Current (Note 1)
200
mA
mW
W
S,INPUT
P
Output Power (Duty Factor ≤ 2.7%) (Note 1)
300
S,OUTPUT
9
R
Insulation Resistance at T , V = 500 V (Note 1)
>10
IO
S
IO
1. Safety limit value – maximum values allowed in the event of a failure.
www.onsemi.com
2
MID400M
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Value
−55 to +125
−40 to +85
−55 to +100
260 for 10 seconds
115
Unit
°C
T
Storage Temperature
Operating Temperature
Junction Temperature
Lead Solder Temperature
STG
OPR
T
°C
T
J
°C
T
°C
SOL
P
D
Total Device Power Dissipation @ T = 25°C
mW
mW/°C
A
Derate Above 70°C
4
EMITTER
RMS Current
DC Current
25
30
45
2
mA
mA
P
LED Power Dissipation @ T = 25°C
mW
D(EMITTER)
A
Derate Above 70°C
mW/°C
DETECTOR
I
Low Level Output Current
High Level Output Voltage
Supply Voltage
20
7
mA
V
OL
V
V
OH
7
V
CC
P
Detector Power Dissipation @ T = 25°C
70
2
mW
mW/°C
D(DETECTOR)
A
Derate Above 70°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
www.onsemi.com
3
MID400M
ELECTRICAL CHARACTERISTICS (0°C to 70°C Free Air Temperature unless otherwise specified)
Symbol
Parameter
Test Conditions
Min
Typ
Max
Unit
INDIVIDUAL COMPONENT CHARACTERISTICS
EMITTER
V
Input Forward Voltage
I
=
30 mA
−
−
−
−
1.5
3.0
V
F
IN(DC)
DETECTOR
I
Logic Low Output Supply Current
I
= 4.0 mA,
mA
CCL
IN(RMS)
V
= Open, V = 5.5V,
O
CC
24 V ≤ V
≤ 240 V
IN(ON_RMS)
I
Logic High Output Supply Current
I
V
V
= 0.15 mA,
−
−
0.8
mA
CCH
IN(RMS)
CC
= 5.5 V,
≥ 5.5 V
IN(OFF_RMS)
TRANSFER CHARACTERISTICS
DC CHARACTERISTICS
V
Logic Low Output Current
Logic High Output Current
On−state RMS Input Voltage
Off−state RMS Input Voltage
On−state RMS Input Current
Off−state RMS Input Current
I
= I
CC
, I = 16 mA,
−
−
0.18
0.02
−
0.40
100
−
V
mA
V
OL
IN
IN(ON_RMS)
O
V
= 4.5 V,
24 V ≤ V
≤ 240 V
IN(ON_RMS)
I
I
= 0.15 mA,
OH
IN(RMS)
V
= V = 5.5 V,
IN(OFF_RMS)
O
CC
V
≥ 5.5 V
V
I
= 16 mA,
90
−
IN(ON_RMS)
O
V
= 0.4 V, V = 4.5 V,
O
CC
R
= 22 kW
IN
V
I
I
≤ 100 mA,
−
5.5
−
V
IN(OFF_RMS)
IN(ON_RMS)
IN(OFF_RMS)
O
V
= V = 5.5 V,
O
CC
R
= 22 kW
IN
I
= 16 mA,
= 0.4 V, V = 4.5 V,
4.0
−
−
mA
mA
O
V
O
CC
IN(ON_RMS)
24 V ≤ V
≤ 240 V
I
I
≤ 100 mA,
= V = 5.5 V,
IN(OFF_RMS)
−
0.15
O
V
O
CC
V
≥ 5.5 V
AC CHARACTERISTICS
t
Turn−On Time
Turn−Off Time
I
= 4.0 mA, I = 16 mA,
−
−
1.0
1.0
−
−
ms
ms
ON
IN(RMS)
CC
O
V
= 4.5 V, R = 22 kW
IN
t
(See figure 3)
OFF
ISOLATION CHARACTERISTICS
V
ISO
Steady State Isolation Voltage
Relative Humidity ≤ 50%,
I−O
5,000
−
−
VAC
RMS
I
≤ 10 mA, 1 Minute, 60 Hz
C
R
Isolation Capacitance
Isolation Resistance
f = 1 MHz
= 500 VDC
−
−
−
2
pF
ISO
ISO
11
V
10
−
W
I−O
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
4
MID400M
APPLICATION INFORMATION
GLOSSARY
Voltages
The input of the MID400M consists of two back−to−back
LED diodes which will accept and convert alternating
currents into light energy. An integrated photo
diode−detector amplifier forms the output network. Optical
V
IN (ON_RMS)
On−State RMS Input Voltage
coupling between input and output provides 2500 VAC
The RMS voltage at an input terminal for a specified input
current with output conditions applied according to the
product specification will cause the output switching
element to be sustained in the on−state within one full cycle.
RMS
voltage isolation. A very high current transfer ratio (defined
as the ratio of the DC output current and the DC input
current) is achieved through the use of high gain amplifier.
The detector amplifier circuitry operates from a 5 V DC
supply and drives an open collector transistor output. The
switching times are intentionally designed to be slow in
order to enable the MID400M, when used as an AC line
monitor, to respond only to changes in input voltage
exceeding many milliseconds. The short period of time
during zero−crossing which occurs once every half cycle of
the power line is completely ignored. To operate the
V
IN (OFF_RMS)
Off−State RMS Input Voltage
The RMS voltage at an input terminal for a specified input
current with output conditions applied according to the
product specification will cause the output switching
element to be sustained in the off−state within one full cycle.
V
OL
Low−Level Output Voltage
The voltage at an output terminal for a specific output
MID400M, always add a resistor, R , in series with the
IN
input (as shown in figure 2) to limit the current to the
required value. The value of the resistor can be determined
by the following equation:
current I , with input conditions applied according to the
OL
product specification will establish a low−level at the output.
VIN * VF
V
OH
RIN
+
(eq. 1)
High−Level Output Voltage
IIN
The voltage at an output terminal for a specific output
Where,
(RMS) is the input voltage.
current I , with input conditions applied according to the
OH
V
IN
product specification will establish a high−level at the
output.
V is the forward voltage drop across the LED.
F
I
(RMS) is the desired input current required to sustain a
V
F
IN
logic “O” on the output.
LED Forward Voltage
The voltage developed across the LED when input current
I is applied to the anode of the LED.
F
PIN DESCRIPTION
Pin
Number
Pin
Name
Currents
Description
I
IN (ON_RMS)
1, 3
2, 4
8
V
, V
Input terminals
No Connect
IN1
IN2
On−State RMS Input Current
N/C
The RMS current flowing into an input with output
conditions applied according to the product specification
will cause the output switching element to be sustained in the
on−state within one full cycle.
V
CC
Supply voltage, output circuit.
7
AUX
Auxiliary terminal.
Programmable capacitor input to adjust
AC voltage sensing level and time delay.
I
IN (OFF_RMS)
6
5
V
O
Output terminal; open collector.
Circuit ground potential.
Off−state RMS Input Current
The RMS current flowing into an input with output
conditions applied according to the product specification
will cause the output switching element to be sustained in the
off−state within one full cycle.
GND
SCHEMATIC DIAGRAM
I
OH
VIN1
N/C
VIN2
N/C
1
2
3
4
8
7
6
5
VCC
AUX.
VO
High−Level Output Current
The current flowing into an output with input conditions
applied according to the product specification will establish
high−level at the output.
GND
Figure 1. Schematic Diagram
www.onsemi.com
5
MID400M
I
OL
Dynamic Characteristics
Low−Level Output Current
t
ON
The current flowing into an output with input conditions
applied according to the product specification will establish
low−level at the output.
Turn−On Time
The time between the specified reference points on the
input and the output voltage waveforms with the output
changing from the defined high−level to the defined
low−level.
I
CCL
Supply Current, Output LOW
The current flowing into the V supply terminal of a
circuit when the output is at a low−level voltage.
CC
t
OFF
Turn−Off Time
I
The time between the specified reference points on the
input and the output voltage waveforms with the output
changing from the defined low−level to the defined
high−level.
CCH
Supply Current, Output HIGH
The current flowing into the V supply terminal of a
CC
circuit when the output is at a high−level voltage.
www.onsemi.com
6
MID400M
TEST CIRCUITS
V
CC
R
= 22 kW
IN
1
2
3
4
8
V
IN
7
6
5
R = 300 W
AC INPUT
L
C
AUX
V
O
INPUT CURRENT VS. CAPACITANCE, C
CIRCUIT
AUX
Figure 2. Typical Application Circuit
A−C
INPUT
OV
t
t
OFF
ON
V
OH
OUTPUT 50%
50%
V
OL
*INPUT TURNS ON AND OFF AT ZERO CROSSING
+4.5 V
V
CC
1
8
1 INPUT
N/C
V
CC
2
3
4
7
6
5
A−C
INPUT
AUX.
R
300 W
L
R
IN
2 INPUT
N/C
V
OUT
22 kW
OUTPUT
GND
TEST CIRCUIT
Figure 3. MID400 Switching Time
www.onsemi.com
7
MID400M
TYPICAL PERFORMANCE CURVES
250
200
150
100
50
30
T = 25°C
CC
T = 25°C
A
CC
A
V
= 5.0 V
V
= 5.0 V
25
20
15
10
5
TURN OFF
TURN ON
I
≤ mA
OH
I
OL
= 16 mA
50
0
0
0
10
20
30
40
60
0
10
20
R , INPUT RESISTANCE (kW)
IN
30
40
50
60
R
, INPUT RESISTANCE (kW)
IN
Figure 4. Input Voltage vs. Input Resistance
Figure 8. Input Voltage vs. Input Resistance
2.8
120
V
CC
= 5.0 V
I
I
R
= 16 mA
≤ mA
= 22 kW
OL
2.4
2.0
1.6
1.2
OH
110
100
IN
T = 25°C
A
I
IN (ON)
I
CCL
0.8
0.4
0
90
80
I
IN (OFF)
I
CCH
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
10
20
50
100
200
500
1000
CAPACITANCE (pF) (AUX. TO GND)
V
CC
, SUPPLY VOLTAGE (V)
Figure 5. Supply Current vs. Supply Voltage
Figure 7. Input Current vs. Capacitance
0.30
0.20
4.5 V
5.0 V
I
= 4.0 mA
IN (ON_RMS)
0.15
0.10
0.05
0
0
5.0
10.0
15.0
20.0
25.0
I
OL
, OUTPUT CURRENT (mA)
Figure 6. Output Voltage vs. Output Current
www.onsemi.com
8
MID400M
REFLOW PROFILE
Max. Ramp−up Rate = 3°C/S
Max. Ramp−down Rate = 6°C/S
TP
TL
260
240
220
200
180
160
140
120
100
80
tP
Tsmax
tL
Preheat Area
Tsmin
ts
60
40
20
0
120
240
360
Time 25°C to Peak
Time (seconds)
Profile Freature
Pb−Free Assembly Profile
150°C
Temperature Minimum (Tsmin)
Temperature Maximum (Tsmax)
200°C
Time (t ) from (Tsmin to Tsmax)
60 to 120 s
S
Ramp−up Rate (t to t )
3°C/second maximum
217°C
L
P
Liquidous Temperature (T )
L
Time (t ) Maintained Above (T )
60 to 150 s
L
L
Peak Body Package Temperature
Time (t ) within 5°C of 260°C
260°C +0°C / –5°C
30 s
P
Ramp−down Rate (T to T )
6°C/s maximum
8 minutes maximum
P
L
Time 25°C to Peak Temperature
Figure 9. Reflow Profile
www.onsemi.com
9
MID400M
ORDERING INFORMATION
Part Number
†
Package
Shipping
MID400M
DIP 8−Pin
(Pb−Free)
50 / Tube
50 / Tube
MID400SM
SMT 8−Pin (Lead Bend)
(Pb−Free)
MID400SDM
MID400VM
SMT 8−Pin (Lead Bend)
(Pb−Free)
1,000 / Tape and Reel
50 / Tube
DIP 8−Pin, DIN EN/IEC 60747−5−5 Option
(Pb−Free)
MID400SVM
MID400SDVM
MID400TVM
SMT 8−Pin (Lead Bend), DIN EN/IEC 60747−5−5 Option
(Pb−Free)
50 / Tube
SMT 8−Pin (Lead Bend), DIN EN/IEC 60747−5−5 Option
(Pb−Free)
1,000 / Tape and Reel
50 / Tube
DIP 8−Pin, 0.4” Lead Spacing, DIN EN/IEC 60747−5−5 Option
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
10
MID400M
PACKAGE DIMENSIONS
PDIP8 6.6x3.81, 2.54P
CASE 646BW
ISSUE O
www.onsemi.com
11
MID400M
PACKAGE DIMENSIONS
PDIP8 9.655x6.6, 2.54P
CASE 646CQ
ISSUE O
www.onsemi.com
12
MID400M
PACKAGE DIMENSIONS
PDIP8 GW
CASE 709AC
ISSUE O
www.onsemi.com
13
MID400M
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
onsemi Website: www.onsemi.com
◊
www.onsemi.com
相关型号:
©2020 ICPDF网 联系我们和版权申明