N34TS108MUET3G [ONSEMI]
LowâVoltage Digital Temperature Sensor;型号: | N34TS108MUET3G |
厂家: | ONSEMI |
描述: | LowâVoltage Digital Temperature Sensor |
文件: | 总16页 (文件大小:326K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
N34TS108
Low‐Voltage Digital
Temperature Sensor
Description
N34TS108 is a digital-output temperature sensor with a
dynamically-programmable limit window, and under- and over
temperature alert functions. These features provide optimized
temperature control without the need of frequent temperature readings
by the controller or application processor.
www.onsemi.com
The N34TS108 features SMBus t and two-wire interface
compatibility, and allows up to three devices on one bus with the
SMBus alert function.
The N34TS108 is ideal for thermal management optimization in
a variety of consumer, computer, and environmental applications. The
device is specified over a temperature range of –40°C to +125°C.
WLCSP6
C6 SUFFIX
CASE 567WQ
FUNCTION DIAGRAM
Features
Diode
A2
A1
V+
• Dynamically-Programmable Limit Window with Under- and Over
Control
Temp
Logic
Temperature Alerts
GND
Sensor
• Accuracy:
♦
♦
0.75°C (max) from –20°C to +85°C
1°C (max) from –40°C to +125°C
B1
A0
B2
C2
DS
Serial
Interface
ADC
SCL
SDA
• Low Quiescent Current:
♦ 6 mA Active from –40°C to +125°C
• Supply Range: 1.4 V to 3.6 V
• Resolution: 12 Bits (0.0625°C)
• Package: 1.2-mm × 0.8-mm, 6-Ball WCSP
Config
and Temp
Register
C1
ALERT
OSC
Typical Applications
• Smartphone and Tablet Thermal Management
• Battery Management
MARKING DIAGRAM
T
YW
• Thermostat Control
• Under- and Over Temperature Protection for Environmental
(WLCPA)
Monitoring and HVAC
T
Y
= Specific Device Code
= Year
Table 1. ABSOLUTE MAXIMUM RATINGS
W
= Work Week
Parameter
Rating
3.6
Unit
V
Supply Voltage
Input Voltage
ORDERING INFORMATION
See detailed ordering and shipping information on page 12 of
this data sheet.
−0.5 to 3.6
−55 to 150
150
V
Operating Temperature
Junction Temperature (T )
°C
°C
°C
J
Storage Temperature (T
)
−60 to 150
stg
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
© Semiconductor Components Industries, LLC, 2014
1
Publication Order Number:
February, 2020 − Rev. 1
N34TS108/D
N34TS108
PIN CONFIGURATION
WLCSP6
UDFN6
Pin 1
V
Pin 1
GND
A1
A2
B2
C2
CC
SDA
SCL
GND
A0
B1
C1
SCL
SDA
V
CC
ALERT
ALERT
A0
(Top View)
(Top View)
Table 2. ESD RATINGS
ESD Rating
Human body model (HBM), per ANSI/ESDA/JEDEC JS−001, all pins11l
Charged device model (COM), per JEDEC specification JESD22−C101, all pins
Value
2000
1000
Unit
V
V(ESD) Electrostatic
Discharge
V
Table 3. D.C. OPERATING CHARACTERISTICS (V = 1.8 V, T = 25°C, unless otherwise specified)
CC
A
Parameter
TEMPERATURE INPUT
Range
Conditions
Min
Typ
Max
Unit
–40
+125
0.75
1
°C
°C
Accuracy (Temperature Error)
–20°C to +85°C
–40°C to +125°C
0.15
0.3
°C
Accuracy vs. Supply
0.03
0.3
°C/V
DIGITAL INPUT/OUTPUT
V
V
Input Logic High Level
Input Logic Low Level
Input Current
0.7 (VCC)
VCC
0.3 (VCC)
1
V
V
IH
IL
−0.5
I
IN
0 V < V < (VCC) +0.3 V
mA
IN
V
Output Logic Low Level
VCC > 2 V, I
= 3 mA
= 3 mA
0.4
V
OL
OUT
OUT
VCC < 2 V, I
0.2 (VCC)
120
V
ALERT Internal Pull-up Resistor
Resolution
ALERT to VCC
80
17
100
12
22
0.25
1
kW
Bit
Conversion Time
One-Shot mode
28
ms
Conversion Modes
CR1 = 0, CR0 = 0
Conv/s
Conv/s
Conv/s
Conv/s
ms
CR1 = 0, CR0 = 1 (default)
CR1 = 1, CR0 = 0
4
CR1 = 1, CR0 = 1
16
30
Timeout Time
21
35
POWER SUPPLY
Operating Supply Range,
VCC Pin
1.4
3.6
V
www.onsemi.com
2
N34TS108
Table 3. D.C. OPERATING CHARACTERISTICS (V = 1.8 V, T = 25°C, unless otherwise specified)
CC
A
Parameter
POWER SUPPLY
Quiescent Current
Conditions
Min
Typ
Max
Unit
I
Q
Serial bus inactive, CR1 = 0, CR0 = 1 (default)
3.1
6
3.6
mA
mA
Serial bus inactive, CR1 = 0, CR0 = 1 (default),
–40°C to +125°C
Serial bus active, SCL frequency = 400 kHz,
CR1 = 0, CR0 = 1 (default)
8
mA
mA
Serial bus active, SCL frequency = 3.4 MHz,
CR1 = 0, CR0 = 1 (default)
41
Shutdown Current
Serial bus inactive
2.5
8
3.1
mA
mA
mA
ISD
Serial bus active, SCL frequency = 400 kHz
Serial bus active, SCL frequency = 3.4 MHz
41
TEMPERATURE
Specified Range
Storage Range
–40
–55
+125
+150
°C
°C
www.onsemi.com
3
N34TS108
Table 4. A.C. OPERATING CHARACTERISTICS (V = 1.4 V to 3.6 V, T = −40°C to +125°C)
CC
A
Fast Mode
High Speed Mode
Min
Max
0.4
Min
0.001
0.001
160
Max
3.4
Parameter
Test Conditions
SCL Operating Frequency, VCC ≥ 1.8 V
SCL Operating Frequency, VCC < 1.8 V
Unit
MHz
MHz
ns
f(SCL)
0.001
0.001
1300
1300
600
0.4
2.5
t(BUF)
Bus Free Time between Stop and Start Conditions, VCC
Bus Free Time between Stop and Start Conditions, VCC
260
ns
t(HDSTA)
Hold Time after Repeated Start Condition.
After this period, the first clock is generated.
160
ns
t(SUSTA)
t(SUSTO)
t(HDDAT)
Repeated Start Condition Setup Time
Stop Condition Setup Time
600
600
0
160
160
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Data Hold Time, VCC ≥ 1.8 V
Data Hold Time, VCC < 1.8 V
Data Setup Time, VCC ≥ 1.8 V
Data Setup Time, VCC < 1.8 V
SCL Clock Low Period, VCC ≥ 1.8 V
SCL Clock Low Period, VCC < 1.8 V
SCL Clock High Period
900
900
70
0
0
130
t(SUDAT)
t(LOW)
100
100
1300
1300
600
10
50
160
260
60
t(HIGH)
t , t − SDA
Data Rise/Fall Time
300
300
80
40
R
F
t , t − SCL
Clock Rise/Fall Time
R
F
t
R
Clock/Data Rise Time for SCLK ≤ 100 kHz
1000
1. For the N34TS108, the interface will reset itself and will release the SDA line if the SCL line stays low beyond the t
limit. The time-out
TIMEOUT
count takes place when SCL is low in the time interval between START and STOP.
2
2. In a “Wired-OR” system (such as I C or SMBus), SDA rise time is determined by bus loading. Since each bus pull-down device must be able
to sink the (external) bus pull-up current (in order to meet the V and/or V limits), it follows that SDA fall time is inherently faster than SDA
IL
OL
rise time. SDA rise time can exceed the standard recommended t limit, as long as it does not exceed t
− t − t
DH
, where t
and
R
LOW
SU:DAT
LOW
t
are actual values (rather than spec limits). A shorter t leaves more room for a longer SDA t , allowing for a more capacitive bus or
DH
DH R
a larger bus pull-up resistor.
3. The first valid temperature recording can be expected after t at nominal supply voltage.
PU
Table 5. PIN CAPACITANCE (V = 3.6 V, T = 25°C, f = 400 kHz)
CC
A
Symbol
Parameter
Test Conditions/Comments
= 0
Min
Max
8
Unit
pF
C
SDA, Pin Capacitance
Input Capacitance (SCL)
V
V
IN
IN
= 0
6
pF
IN
Table 6. PIN DESCRIPTIONS
Pin Name
A0
Ball Number
Description
B1
C1
A2
B2
C2
A1
Address selection pin
Alert output pin
Ground
ALERT
GND
SCL
Input clock pin
Input/output data pin
SDA
VCC
Supply Voltage (1.4 V to 3.6 V)
www.onsemi.com
4
N34TS108
SCL
SDA
START
CONDITION
STOP
CONDITION
Figure 1. START/STOP Timing
BUS RELEASE DELAY (TRANSMITTER)
BUS RELEASE DELAY
(RECEIVER)
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
ACK SETUP (≥ t
)
SU:DAT
START
ACK DELAY (≤ t
)
AA
Figure 2. Acknowledge Timing
t
t
t
R
F
HIGH
t
t
LOW
LOW
SCL
t
t
HD:DAT
SU:STA
t
t
SU:STO
t
SU:DAT
HD:STA
SDA IN
t
BUF
t
t
DH
AA
SDA OUT
Figure 3. Bus Timing
OVERVIEW
The N34TS108 only requires pull-up resistors on SCL and
SDA; although, a 0.01 mF bypass capacitor is recommended.
There is an internal 100 kW pull-up resistor connected to
supply on the ALERT pin. If required, use an external
resistor of smaller value on the ALERT pin for a stronger
pull-up to VCC. The SCL and SDA lines can be pulled up
to a supply that is equal to or higher than VCC through the
pull-up resistors. To configure one of three different
addresses on the bus, connect AO to either VCC, GND, or
SDA. If AO is connected to SDA, make its pull-up supply
equal to VCC.
The N34TS108 is a digital temperature sensor optimal for
thermal management and thermal protection applications.
The N34TS108 is two-wire and SMBus Interface
compatible, and is specified over a temperature range of
−40°C to +125°C.
The N34TS108 temperature sensor is the chip itself; the
solder bumps provide the primary thermal path as a result of
the lower thermal resistance of metal. The temperature
sensor result is equivalent to the local temperature of the
printed circuit board (PCB) on which the sensor is mounted.
www.onsemi.com
5
N34TS108
POINTER REGISTER
Figure 4 shows the internal register structure of the
N34TS108. Use the 8-bit pointer register to address a given
data register. The pointer register uses the two LSBs (see
Table 16) to identify which of the data registers respond to
a read or write command. Table 7 identifies the bits of the
pointer register byte. Table 8 describes the pointer address
of the registers available in the N34TS108. The power-up
reset value of the P1 and P0 bits is ‘00’.
Pointer
Register
Temperature
Register
SCL
Configuration
Register
I/O
Control
Interface
T
LOW
Register
SDA
T
HIGH
Register
Figure 4. Internal Register Structure
Table 7. POINTER REGISTER BYTE
P7
P6
P5
P4
P3
P2
P1
P0
0
0
0
0
0
0
Register Bits
Table 8. POINTER ADDRESSES
P1
0
P0
0
Register
Temperature Register (Read Only, Default)
Configuration Register (Read/write)
0
1
1
0
T
Register (Read/Write)
Register (Read/Write)
LOW
HIGH
1
1
T
www.onsemi.com
6
N34TS108
TEMPERATURE REGISTER
The temperature register is configured as a 12-bit,
read-only register that stores the output of the most recent
conversion. Two bytes must be read to obtain data, as shown
in Table 9 and Table 10. Note that byte 1 is the most
significant byte, followed by byte 2, the least significant
byte. The first 12 bits are used to indicate temperature. There
is no requirement to read the least significant byte if that
information is not needed (for example, for resolution lower
than 1°C). Table 5 summarizes the temperature data format.
One LSB equals 0.0625°C. Negative numbers are
represented in binary twos complement format. Following
power-up or reset, the temperature register reads 0°C until
the first conversion is complete. The unused bits in the
temperature register always read ‘0’.
Table 9. BYTE 1 OF TEMPERATURE REGISTER
D7
D6
D5
D4
D3
D2
D1
D0
T11
T10
T9
T8
T7
T6
T5
T4
Table 10. BYTE 2 OF TEMPERATURE REGISTER
D7
D6
D5
D4
D3
D2
D1
D0
T3
T2
T1
T0
0
0
0
0
Table 11. TEMPERATURE DATA FORMAT (Note 4)
Digital Output
Binary
Hex
Temperature (5C)
128
127.9375
100
80
0111 1111 1111
0111 1111 1111
7FF
7FF
640
500
4B0
320
190
004
000
FFC
E70
C90
0110 0100 0000
0101 0000 0000
0100 1011 0000
0011 0010 0000
0001 1001 0000
0000 0000 0100
0000 0000 0000
1111 1111 1100
1110 0111 0000
1100 1001 0000
75
50
25
0.25
0
–0.25
–25
–55
4. The temperature sensor ADC resolution is 0.0625°C/count.
Table 11 does not supply a full list of all temperatures. Use
the following rules to obtain the digital data format for
a given temperature.
• To convert negative temperatures to a digital data
format:
Divide the absolute value of the temperature by the
resolution, and convert the result to binary code with
a 12-bit, left-justified format. Then, generate the twos
complement of the result by complementing the binary
number and adding one. Denote a negative number with
MSB = 1.
• To convert positive temperatures to a digital data
format:
Divide the temperature by the resolution. Then, convert
the result to binary code with a 12-bit, left-justified
format, and MSB = 0 to denote a positive sign.
Example: (+50°C)/(0.0625°C/count) = 800 = 320h =
0011 0010 0000
Example: (|–25°C|)/(0.0625°C/count) = 400 = 190h =
0001 1001 0000
Twos complement format: 1110 0110 1111 + 1 = 1110
0111 0000
www.onsemi.com
7
N34TS108
CONFIGURATION REGISTER
performed MSB first. The format and power-up (reset)
default value of the configuration register is shown in
Table 12, followed by an explanation of the register bits.
Other options for the default values are available by request.
The configuration register is a 16-bit read and write
register used to store bits that control the operational modes
of the temperature sensor. Read and write operations are
Table 12. CONFIGURATION AND POWER-UP/RESET FORMAT
Byte
D7
ID
D6
CR1
0
D5
CR0
1
D4
FH
0
D3
FL
0
D2
TM
1
D1
M1
1
D0
M0
0
1
0
2
POL
0
0
HYS1
0
HYS0
1
0
0
0
0
0
0
0
0
0
Hysteresis Control (HYS1 and HYS0)
When operating in comparator mode, the hysteresis
control bits (HYS1 and HYS0) configure the hysteresis for
the limit comparison of the N34TS108 to 0°C, 1°C, 2°C, or
4°C. The default hysteresis is 1°C. Table 13 shows the
settings for HYS1 and HYS0.
Table 13. HYSTERESIS SETTINGS
HYS1
HYS2
Hysteresis
0°C
0
0
1
1
0
1
0
1
1°C (Default)
2°C
4°C
Polarity (POL)
useful for reducing the power consumption of the
N34TS108 when continuous temperature monitoring is not
required.
As a result of the short conversion time, the N34TS108
can achieve a higher conversion rate. A single conversion
typically takes 22 ms and a read can take place in less than
20 ms. However, when using one-shot mode, 30 or more
conversions per second are possible.
The polarity of the ALERT pin can be programmed using
the POL bit. If POL = ‘0’ (default), the ALERT is active low.
For POL = ‘1’, the ALERT pin is active high, and the state
of the ALERT pin is inverted.
Mode Bits (M1 and M0)
The mode bits, M1 and M0, can be set to three different
modes: shutdown, one-shot, or continuous conversion.
Continuous Conversion Mode (M1 = ‘1’)
Shutdown Mode (M1 = ‘0’, M0 = ‘0’)
When the N34TS108 is in continuous conversion mode
(M1 = ‘1’), a single conversion is performed at a rate
determined by the conversion rate bits (CR1 and CR0 in the
configuration register). The N34TS108 performs a single
conversion, and then goes in standby and waits for the
appropriate delay set by the CR1 and CR0 bits. See Table 14
for CR1 and CR0 settings.
Shutdown mode saves power by shutting down all device
circuitry other than the serial interface, thus reducing current
consumption to typically less than 2.5 mA. Shutdown mode
is enabled when M1 and M0 = ‘00’. The device shuts down
when current conversion is completed.
One-Shot Mode (M1 = ‘0’, M0 = ‘1’)
The N34TS108 features
a one-shot temperature
Thermostat Mode (TM)
measurement mode. When the device is in shutdown mode,
writing a ‘01’ to the M1 and M0 bits starts a single
temperature conversion. During the conversion, the M1 and
M0 bits reads ‘01’. The device returns to the shutdown state
at the completion of the single conversion. After the
conversion, the M1 and M0 bits read ‘00’. This feature is
The thermostat mode bit indicates to the device whether
to operate in comparator mode (TM = ‘0’) or interrupt mode
(TM = ‘1’, default). For more information on comparator
and interrupt modes, see the High- and Low-Limit Registers
section.
www.onsemi.com
8
N34TS108
Temperature Watchdog Flags (FL and FH)
SMBus ALERT Response only clears the pin and not the
flags. Reading the configuration register clears both the
flags and the pin unless the device is in comparator mode.
The N34TS108 uses temperature watchdog flags in the
configuration register that indicate the result of comparing
the device temperature at the end of every conversion to the
Conversion Rate
values stored in the temperature limit registers (T
and
HIGH
The conversion rate bits, CR1 and CR0, configure the
N34TS108 for conversion rates of 0.25 Hz, 1 Hz, 4 Hz, or
16 Hz. The default rate is 1 Hz. The N34TS108 has a typical
conversion time of 22 ms. To achieve different conversion
rates, the N34TS108 makes a conversion, and then powers
down and waits for the appropriate delay set by CR1 and
CR0. Table 14 shows the settings for CR1 and CR0.
T
). If the temperature of the N34TS108 exceeds the
LOW
value in the T
register, then the flag-high bit (FH) in the
HIGH
configuration register is set to ‘1’. If the temperature falls
below the value in the T register, then the flag-low bit
LOW
(FL) is set to ‘1’. If both flag bits remain ‘0’, then the
temperature is within the temperature range set by the
temperature limit registers. In interrupt mode, when any of
the flags is set by an under- or over-temperature event, the
Table 14. CONVERSION RATE SETTINGS
CR1
CR0
Conversion Rate
0.25 Hz
I (Typ)
Q
0
0
1
1
0
1
0
1
3 mA
4 mA
1 Hz (Default)
4 Hz
5 mA
16 Hz
13 mA
After power-up or a general-call reset, the N34TS108
immediately starts a conversion, as shown in Figure 5. The
first result is available after 22 ms (typical). The active
quiescent current during conversion is 27 mA (typical at
+25°C). The quiescent current during delay is 2.5 mA
(typical at +25°C).
Delay*
Delay*
22 ms
22 ms
22 ms
Start of
Conversion
Start of
Conversion
Startup
*Delay is set by the CR1 and CR0 bits in the configuration register.
Figure 5. Conversion Start
HIGH- AND LOW-LIMIT REGISTERS
In comparator mode (TM = ‘0’), the ALERT pin becomes
active when the temperature exceeds the value in the T
In interrupt mode (TM = ‘1’), the ALERT pin becomes
HIGH
active when the temperature exceeds the value in the T
HIGH
register or drops below the value in the T
register. The
LOW
register or drops below the value in the T
register, and
LOW
ALERT pin remains active until the temperature returns to
a value that is within the range set by:
remains active until a read operation of the configuration
register occurs (also clears the values latched in the
watchdog flags, FL and FH), or the device successfully
responds to the SMBus alert response address. The ALERT
pin is also cleared by resetting the device with the general
call reset command.
(TLOW ) HYS) and (THIGH * HYS)
(eq. 1)
Where:
HYS is the hysteresis set by the hysteresis control bits
(HYS1 and HYS0).
www.onsemi.com
9
N34TS108
Both operational modes are represented in Figure 6 and
Figure 7.
= –128°C. These values ensure that upon power-up, the limit
window is set to maximum, and the ALERT pin does not
become active until the desired limit values are programmed
in the registers. Other default values for the temperature
limits are available by request. The format of the data for
Table 15 and Table 16 describe the format for the T
HIGH
and T
registers. Note that the most significant byte is
LOW
sent first, followed by the least significant byte. Power-up
(reset) default values are T = +127.9375°C and T
T
and T
is the same as for the temperature register.
HIGH
LOW
HIGH
LOW
Table 15. BYTES 1 AND 2 OF THIGH REGISTER
Byte
D7
D6
D5
D4
D3
D2
D1
D0
1
H11
H10
H9
H8
H7
H6
H5
H4
Byte
D7
D6
D5
D4
D3
D2
D1
D0
2
H3
H2
H1
H0
0
0
0
0
Table 16. BYTES 1 AND 2 OF TLOW REGISTER
Byte
D7
D6
D5
D4
D3
D2
D1
D0
1
L11
L10
L9
L8
L7
L6
L5
L4
Byte
D7
D6
D5
D4
D3
D2
D1
D0
2
L3
L2
L1
L0
0
0
0
0
NOTE: Update T
and T
limit. Read the configuration register to clear the flags and the ALERT pin.
HIGH
LOW
Figure 6. Interrupt Mode
www.onsemi.com
10
N34TS108
Figure 7. Comparator Mode
SERIAL INTERFACE
SERIAL BUS ADDRESS
The N34TS108 operates as a slave device only on the
two-wire bus and SMBus. Connections to the bus are made
using the open-drain I/O lines, SDA and SCL. The SDA and
SCL pins feature integrated spike-suppression filters and
Schmitt triggers to minimize the effects of input spikes and
bus noise. The N34TS108 supports the transmission
protocol for both fast (1 kHz to 400 kHz) and high-speed
(1 kHz to 3.4 MHz) modes. All data bytes are transmitted
MSB first.
To communicate with the N34TS108, the master must
first communicate with slave devices using a slave address
byte. The slave address byte consists of seven address bits,
and a direction bit indicating the intent of executing either
a read or write operation. The N34TS108 features an address
pin that allows up to three devices to be addressed on a single
bus. The N34TS108 latches the status of the address pin at
the start of a communication. Table 17 describes the pin
logic levels and the corresponding address values. Other
values for the fixed address bits are available by request.
Table 17. ADDRESS PIN AND SLAVE ADDRESSES
Device Two-wire Address
1001000
A0 Pin Connection
GND
VCC
SDA
SCL
1001001
1001010
1001011
BUS OVERVIEW
change in SDA while SCL is high is interpreted as a start or
stop signal.
After all data have been transferred, the master generates
a stop condition indicated by pulling SDA from low to high,
while SCL is high.
The device that initiates the transfer is called a master, and
the devices controlled by the master are slaves. The bus must
be controlled by a master device that generates the serial
clock (SCL), controls the bus access, and generates the start
and stop
WRITING/READING OPERATION
conditions.
Accessing a particular register on the N34TS108 is
accomplished by writing the appropriate value to the pointer
register. The value for the pointer register is the first byte
transferred after the slave address byte with the R/W bit low.
Every write operation to the N34TS108 requires a value for
the pointer register.
When reading from the N34TS108, the last value stored
in the pointer register by a write operation is used to
determine which register is read by a read operation. To
change the register pointer for a read operation, a new value
To address a specific device, initiate a start condition by
pulling the data line (SDA) from a high to a low logic level
while SCL is high. All slaves on the bus shift in the slave
address byte; the last bit indicates whether a read or write
operation follows. During the ninth clock pulse, the slave
being addressed responds to the master by generating an
acknowledge bit and pulling SDA low.
Data transfer is then initiated and sent over eight clock
pulses followed by an acknowledge bit. During data transfer,
SDA must remain stable while SCL is high because any
www.onsemi.com
11
N34TS108
must be written to the pointer register. This action is
acknowledges the SMBus alert command and responds by
returning its slave address on the SDA line. The eighth bit
(LSB) of the slave address byte indicates whether the alert
accomplished by issuing a slave address byte with the R/W
bit low, followed by the pointer register byte. No additional
data are required. The master can then generate a start
condition and send the slave address byte with the R/W bit
high to initiate the read command. If repeated reads from the
same register are desired, it is not necessary to continually
send the pointer register bytes because the N34TS108 stores
the pointer register value until it is changed by the next write
operation.
condition is caused by the temperature exceeding T
or
HIGH
falling below T . The LSB is high if the temperature is
LOW
greater than T
, or low if the temperature is less than
HIGH
T
.
LOW
If multiple devices on the bus respond to the SMBus alert
command, arbitration during the slave address portion of the
SMBus alert command determines which device clears its
alert status first. If the N34TS108 wins the arbitration, its
ALERT pin becomes inactive at the completion of the
SMBus alert command. If the N34TS108 loses the
arbitration, its ALERT pin remains active.
Note that register bytes are sent with the most significant
byte first, followed by the least significant byte.
SLAVE MODE OPERATIONS
The N34TS108 can operate as a slave receiver or slave
transmitter.
GENERAL CALL
The N34TS108 responds to a two-wire general call
address (0000000) if the eighth bit is ‘0’. The device
acknowledges the general call address and responds to
commands in the second byte. If the second byte is
00000100, the N34TS108 latches the status of the address
pin, but does not reset. If the second byte is 00000110, the
N34TS108 internal registers are reset to power-up values.
The N34TS108 does not support the general address acquire
command.
Slave Receiver Mode:
The first byte transmitted by the master is the slave
address, with the R/W bit low. The N34TS108 then
acknowledges reception of a valid address. The next byte
transmitted by the master is the pointer register. The
N34TS108 then acknowledges reception of the pointer
register byte. The next byte or bytes are written to the
register addressed by the pointer register. The N34TS108
acknowledges reception of each data byte. The master can
terminate data transfer by generating a start or stop
condition.
HIGH-SPEED (Hs) MODE
In order for the two-wire bus to operate at frequencies
above 400 kHz, the master device must issue an SMBus
Hs-mode master code (00001xxx) as the first byte after
a start condition to switch the bus to high-speed operation.
The N34TS108 does not acknowledge this byte, but does
switch its input filters on SDA and SCL and its output filters
on SDA to operate in Hs-mode, allowing transfers at up to
3.4 MHz. After the Hs-mode master code has been issued,
the master transmits a two-wire slave address to initiate
a data-transfer operation. The bus continues to operate in
Hs-mode until a stop condition occurs on the bus. Upon
receiving the stop condition, the N34TS108 switches the
input and output filters back to fast-mode operation.
Slave Transmitter Mode:
The first byte transmitted by the master is the slave
address, with the R/W bit high. The slave acknowledges
reception of a valid slave address. The next byte is
transmitted by the slave and is the most significant byte of
the register indicated by the pointer register. The master
acknowledges reception of the data byte. The next byte
transmitted by the slave is the least significant byte. The
master acknowledges reception of the data byte. The master
can terminate data transfer by generating a not-acknowledge
bit on reception of any data byte, or by generating a start or
stop condition.
TIMEOUT FUNCTION
SMBus ALERT FUNCTION
The N34TS108 resets the serial interface if SCL or SDA
are held low for 30 ms (typ) between a start and stop
condition. If the N34TS108 is pulled low, it releases the bus
and then waits for a start condition. To avoid activating the
timeout function, it is necessary to maintain
a communication speed of at least 1 kHz for the SCL
operating frequency.
The N34TS108 supports the SMBus alert function. When
the N34TS108 operates in interrupt mode (TM = ‘1’), the
ALERT pin may be connected as an SMBus alert signal.
When a master senses that an alert condition is present on the
ALERT line, the master sends an SMBus alert command
(00011001) to the bus. If the ALERT pin is active, the device
Table 18. ORDERING INFORMATION
†
Device Order Number
N34TS108C6ECT5G
N34TS108MUET3G
Marking
Package Type
WLCSP 6-ball
UDFN 6
Temperature Range
−40°C to +125°C
*40°C to +125°C
Shipping
C
A
5,000 / Tape & Reel
3,000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
5. All packages are RoHS-compliant (Lead-free, Halogen-free).
6. The standard lead/ball finish is SnAgCu.
www.onsemi.com
12
N34TS108
SMBus is a trademark of Intel Corporation
www.onsemi.com
13
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
UDFN6 2x2, 0.65P
CASE 517DR
ISSUE O
DATE 31 OCT 2016
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98AON13696G
UDFN6 2x2, 0.65P
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
WLCSP6, 1.1888x0.788x0.625
CASE 567YQ
ISSUE O
DATE 12 NOV 2019
GENERIC
MARKING DIAGRAM*
X
YW
X
Y
= Specific Device Code
= Year
W
= Work Week
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98AON14165H
WLCSP6, 1.1888x0.788x0.625
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
ON Semiconductor Website: www.onsemi.com
◊
www.onsemi.com
相关型号:
N350CH04
Silicon Controlled Rectifier, 1640.65A I(T)RMS, 320000mA I(T), 400V V(DRM), 400V V(RRM), 1 Element, TO-200AC
IXYS
N350CH04GOO
Silicon Controlled Rectifier, 1640.65A I(T)RMS, 1760000mA I(T), 400V V(DRM), 400V V(RRM), 1 Element, TO-200AC
IXYS
N350CH04HOO
Silicon Controlled Rectifier, 1640.65A I(T)RMS, 1760000mA I(T), 400V V(DRM), 400V V(RRM), 1 Element, TO-200AC
IXYS
N350CH04KOO
Silicon Controlled Rectifier, 1640.65A I(T)RMS, 1760000mA I(T), 400V V(DRM), 400V V(RRM), 1 Element, TO-200AC
IXYS
N350CH04LOO
Silicon Controlled Rectifier, 1640.65A I(T)RMS, 1760000mA I(T), 400V V(DRM), 400V V(RRM), 1 Element, TO-200AC
IXYS
N350CH12JOO
Silicon Controlled Rectifier, 1640.65A I(T)RMS, 1760000mA I(T), 1200V V(DRM), 1200V V(RRM), 1 Element, TO-200AC
IXYS
N350MH02
Silicon Controlled Rectifier, 900A I(T)RMS, 350000mA I(T), 200V V(DRM), 200V V(RRM), 1 Element
IXYS
©2020 ICPDF网 联系我们和版权申明