NCP139AFCT120T2G [ONSEMI]
1 A, Very Low Dropout Bias Rail CMOS Voltage Regulator;型号: | NCP139AFCT120T2G |
厂家: | ONSEMI |
描述: | 1 A, Very Low Dropout Bias Rail CMOS Voltage Regulator |
文件: | 总9页 (文件大小:197K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NCP139
1 A, Very Low Dropout Bias
Rail CMOS Voltage
Regulator
The NCP139 is a 1 A VLDO equipped with NMOS pass transistor
and a separate bias supply voltage (V ). The device provides very
BIAS
www.onsemi.com
stable, accurate output voltage with low noise suitable for space
constrained, noise sensitive applications. In order to optimize
performance for battery operated portable applications, the NCP139
T
MARKING
DIAGRAM
features low I consumption. The WLCSP6 1.2 mm x 0.8 mm Chip
Q
Scale package is optimized for use in space constrained applications.
WLCSP6, 1.2x0.8
CASE 567MV
XXMG
Features
• Input Voltage Range: V
to 5.5 V
OUT
XX = Specific Device Code
M
= Month Code
• Bias Voltage Range: 3.0 V to 5.5 V
G
= Pb−Free Package
• Adjustable and Fixed Voltage Version Available
• Output Voltage Range: 0.4 V to 1.8 V (Fixed)
PIN CONNECTIONS
Output Voltage Range: 0.5 V to 3.0 V (Adjustable)
1
2
•
1% Accuracy over Temperature, 0.5% V
@ 25°C
OUT
• Ultra−Low Dropout: Typ. 50 mV at 1 A
• Very Low Bias Input Current of Typ. 35 mA
A
B
C
VOUT
VIN
• Very Low Bias Input Current in Disable Mode: Typ. 0.5 mA
• Logic Level Enable Input for ON/OFF Control
• Output Active Discharge Option Available
SNS/FB
GND
EN
• Stable with a 10 mF Ceramic Capacitor
• Available in WLCSP6 − 1.2 mm x 0.8 mm, 0.4 mm pitch Package
• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
VBIAS
Typical Applications
• Battery−powered Equipment
• Smartphones, Tablets
• Cameras, DVRs, STB and Camcorders
Top View
ORDERING INFORMATION
See detailed ordering, marking and shipping information on
page 7 of this data sheet.
V
V
BIAS
BIAS
≥3.0 V
≥3.0 V
V
V
OUT
OUT
NCP139 − ADJ
NCP139
GND
1 mF
0.9 V up to 1 Adc,
1.3 A peaks
1 mF
0.9 V up to 1 Adc,
1.3 A peaks
BIAS
BIAS
IN
OUT
FB
OUT
SNS
R1
R2
V
IN
V
IN
IN
10 mF
10 mF
EN
EN
4.7 mF
4.7 mF
GND
V
V
EN
EN
Figure 1. Typical Application Schematics
© Semiconductor Components Industries, LLC, 2017
1
Publication Order Number:
April, 2019 − Rev. 6
NCP139/D
NCP139
CURRENT
LIMIT
OUT
IN
ENABLE
BLOCK
150 W
EN
*Active
DISCHARGE
BIAS
UVLO
V
REF
VOLTAGE
REFERENCE
+
THERMAL
LIMIT
−
FB
GND
*Active output discharge function is present only in NCP139A option devices.
Figure 2. Simplified Schematic Block Diagram − Adjustable Version
CURRENT
LIMIT
OUT
IN
ENABLE
BLOCK
150 W
EN
*Active
DISCHARGE
BIAS
UVLO
VOLTAGE
+
REFERENCE
THERMAL
LIMIT
−
SNS
GND
*Active output discharge function is present only in NCP139A option devices.
Figure 3. Simplified Schematic Block Diagram − Fixed Version
www.onsemi.com
2
NCP139
PIN FUNCTION DESCRIPTION
Pin No.
WLCSP6
Pin Name
VOUT
VIN
Description
A1
Regulated Output Voltage pin
Input Voltage Supply pin
A2
B1
FB
Adjustable Regulator Feedback Input. Connect to output voltage resistor divider central node.
(ADJ devices)
B1
SNS
EN
Output voltage Sensing Input. Connect to Output on the PCB to output the voltage
corresponding to the part version.
(Fix Volt devices)
B2
Enable pin. Driving this pin high enables the regulator. Driving this pin low puts the regulator
into shutdown mode.
C1
C2
GND
Ground pin
VBIAS
Bias voltage supply for internal control circuits. This pin is monitored by internal Under-Voltage
Lockout Circuit.
ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
V
Input Voltage (Note 1)
V
IN
−0.3 to 6
Output Voltage
V
OUT
−0.3 to (V +0.3) ≤ 6
V
IN
Chip Enable, Bias, FB and SNS Input
Output Short Circuit Duration
Maximum Junction Temperature
Storage Temperature
V
V
V
, V
SNS
−0.3 to 6
unlimited
150
V
EN, BIAS, FB
t
s
SC
T
°C
°C
V
J
T
−55 to 150
2000
STG
ESD Capability, Human Body Model (Note 2)
ESD Capability, Machine Model (Note 2)
ESD
HBM
ESD
200
V
MM
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection (except OUT pin) and is tested by the following methods:
ESD Human Body Model tested per EIA/JESD22−A114
ESD Machine Model tested per EIA/JESD22−A115
Latchup Current Maximum Rating tested per JEDEC standard: JESD78.
THERMAL CHARACTERISTICS
Rating
Symbol
Value
Unit
Thermal Characteristics, WLCSP6 1.2 mm x 0.8 mm
RqJA
69
°C/W
Thermal Resistance, Junction−to−Air (Note 3)
3. This junction−to−ambient thermal resistance under natural convection was derived by thermal simulations based on the JEDEC JESD51
series standards methodology. Only a single device mounted at the center of a high_K (2s2p) 80 mm x 80 mm multilayer board with 1−ounce
internal planes and 2−ounce copper on top and bottom. Top copper layer has a dedicated 1.6 sqmm copper area.
www.onsemi.com
3
NCP139
ELECTRICAL CHARACTERISTICS −40°C ≤ T ≤ 85°C; V
= 3.0 V or (V
+ 1.6 V), whichever is greater, V = V
OUT(NOM)
+
J
BIAS
OUT
IN
0.3 V, I
= 1 mA, V = 1 V, C = 10 mF, C
= 10 mF, C
= 1 mF, unless otherwise noted. Typical values are at T = +25°C.
OUT
EN
IN
OUT
BIAS J
Min/Max values are for −40°C ≤ T ≤ 85°C unless otherwise noted. (Notes 4, 5)
J
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
Operating Input Voltage
Range
V
IN
V
+
5.5
V
OUT
DO
V
Operating Bias Voltage
Range
V
(V
+
5.5
V
V
V
BIAS
OUT
1.60) ≥ 3.0
Undervoltage Lock−out
V
Rising
UVLO
1.6
0.2
BIAS
Hysteresis
Reference Voltage
(Adj devices)
NCP139Axxxx05ADJT2G, T = +25°C
V
0.500
0.600
0.5
J
REF
NCP139Axxxx06ADJT2G, T = +25°C
J
Output Voltage Accuracy
V
V
%
%
OUT
Output Voltage Accuracy −40°C ≤ T ≤ 85°C, V
+ 0.3 V ≤ V ≤
IN
−1.0
+1.0
J
OUT(NOM)
OUT
V
+ 1.0 V, 3.0 V or (V
+
OUT(NOM)
OUT(NOM)
1.6 V), whichever is greater < V
< 5.5 V,
BIAS
1 mA < I
< 1.0 A
OUT
V
V
Line Regulation
V
+ 0.3 V ≤ V ≤ 5.0 V
Line
Line
0.01
0.01
%/V
%/V
IN
OUT(NOM)
IN
Reg
Line Regulation
3.0 V or (V
greater < V
+ 1.6 V), whichever is
OUT(NOM)
BIAS
Reg
< 5.5 V
BIAS
Load Regulation
I
I
I
= 1 mA to 1.0 A
Load
2.0
50
OUT
OUT
OUT
Reg
mV
V
V
Dropout Voltage
= 1.0 A (Notes 6, 7)
= 1.0 A, V = V
V
V
80
1.5
mV
IN
DO
Dropout Voltage
(Notes 6, 8, 9)
1.05
2000
2000
0.1
V
BIAS
IN
BIAS
DO
CL
CL
Output Current Limit
V
= 90% V
I
I
1500
1550
2600
2600
0.5
mA
mA
mA
OUT
OUT
OUT(NOM)
OUT(NOM)
V
= 90% V
, −30°C ≤ T ≤ 85°C
J
FB/SNS Pin Operating
Current
I
, I
FB SNS
Bias Pin Quiescent
Current
V
BIAS
= 3.0 V, I
= 0 mA
I
BIASQ
35
50
mA
OUT
Bias Pin Disable Current
V
V
≤ 0.4 V
≤ 0.4 V
I
0.5
0.5
1
1
mA
mA
EN
BIAS(DIS)
Vinput Pin Disable
Current
I
VIN(DIS)
EN
EN Pin Threshold Voltage EN Input Voltage “H”
EN Input Voltage “L”
V
0.9
V
EN(H)
V
0.4
1
EN(L)
EN Pull Down Current
V
EN
= 5.5 V
I
0.3
mA
ms
EN
Turn−On Time
From assertion of V to V
=
t
160
EN
OUT
ON
98% V
. V
= 1.0 V,
OUT(NOM) OUT(NOM)
C
= 10 mF
OUT
Power Supply Rejection
Ratio
(Adj devices)
V
to V
, f = 1 kHz, I
= 10 mA,
= 1.0 V,
PSRR(V )
IN
70
85
dB
dB
IN
OUT
OUT
OUT
VIN ≥ V
+0.5 V, V
OUT(NOM)
C
= 10 mF
OUT
V
to V
OUT
, f = 1 kHz, I
= 10 mA,
= 1.0 V,
PSRR(V
)
BIAS
OUT
OUT
BIAS
VIN ≥ V
+0.5 V, V
OUT(NOM)
C
= 10 mF
OUT
Output Noise Voltage
(Adj devices)
V
V
= V
OUT(NOM)
+0.5 V, f = 10 Hz to 100 kHz,
V
N
35 x
OUT REF
mV
RMS
IN
OUT
= 1.0 V, C
= 10 mF
V
/V
OUT
4. Performance guaranteed over the indicated operating temperature range by design and/or characterization. Production tested at T
=
A
25°C. Low duty cycle pulse techniques are used during the testing to maintain the junction temperature as close to ambient as possible.
5. Adjustable devices tested at V = V unless otherwise noted; external resistor tolerance is not taken into account.
OUT
REF
OUT
6. Dropout voltage is characterized when V
falls 3% below V
.
OUT(NOM)
7. For adjustable devices, V dropout voltage tested at V
= 2 x V
.
IN
OUT(NOM)
OUT(NOM)
REF
8. For adjustable devices, V
dropout voltage tested at V
= 3 x V
due to a minimum Bias operating voltage of 3.0 V.
BIAS
REF
9. For Fixed Voltages below 1.8 V, V
dropout voltage does not apply due to a minimum Bias operating voltage of 3.0 V.
BIAS
www.onsemi.com
4
NCP139
ELECTRICAL CHARACTERISTICS −40°C ≤ T ≤ 85°C; V
= 3.0 V or (V
+ 1.6 V), whichever is greater, V = V
OUT(NOM)
+
J
BIAS
OUT
IN
0.3 V, I
= 1 mA, V = 1 V, C = 10 mF, C
= 10 mF, C
= 1 mF, unless otherwise noted. Typical values are at T = +25°C.
OUT
EN
IN
OUT
BIAS J
Min/Max values are for −40°C ≤ T ≤ 85°C unless otherwise noted. (Notes 4, 5)
J
Parameter
Test Conditions
, f = 1 kHz, I = 10 mA, V
Symbol
Min
Typ
Max
Unit
Power Supply Rejection
Ratio (Fixed Voltage
devices)
V
V
to V
OUT
≥
IN
PSRR(V
)
75
dB
IN
OUT
OUT
= 1.8 V, C
IN
+0.5 V, V
= 10 mF
OUT(NOM)
OUT
V
V
to V
, f = 1 kHz, I
OUT(NOM)
= 10 mA, V
≥
PSRR(V
)
85
48
dB
BIAS
OUT
OUT
OUT
IN
BIAS
+0.5 V, V
= 1.8 V, V
= 4.0 V,
BIAS
C
= 10 mF
OUT
Output Noise Voltage
(Fixed Voltage devices)
V
V
= V
+0.5 V, f = 10 Hz to 100 kHz,
V
N
mVRMS
°C
IN
OUT
= 1.8 V, C
= 10 mF
OUT(NOM)
OUT
Thermal Shutdown
Threshold
Temperature increasing
Temperature decreasing
160
140
150
Output Discharge
Pull−Down
V
≤ 0.4 V, V
= 0.5 V, NCP139A options
R
DISCH
W
EN
OUT
only
4. Performance guaranteed over the indicated operating temperature range by design and/or characterization. Production tested at T
=
A
25°C. Low duty cycle pulse techniques are used during the testing to maintain the junction temperature as close to ambient as possible.
5. Adjustable devices tested at V = V unless otherwise noted; external resistor tolerance is not taken into account.
OUT
REF
OUT
6. Dropout voltage is characterized when V
falls 3% below V
.
OUT(NOM)
7. For adjustable devices, V dropout voltage tested at V
= 2 x V
.
IN
OUT(NOM)
OUT(NOM)
REF
8. For adjustable devices, V
dropout voltage tested at V
= 3 x V
due to a minimum Bias operating voltage of 3.0 V.
BIAS
REF
9. For Fixed Voltages below 1.8 V, V
dropout voltage does not apply due to a minimum Bias operating voltage of 3.0 V.
BIAS
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
5
NCP139
APPLICATIONS INFORMATION
VBAT
NCP139
EN
Switch−mode DC/DC
= 1.5 V
1.0 V
OUT
FB
V
OUT
BIAS
R1
R2
1.5 V
LX
FB
LOAD
IN
IN
GND
EN
Processor
GND
I/O
I/O
To other circuits
Figure 4. Typical Application: Low−Voltage DC/DC Post−Regulator with ON/OFF Functionality
Dropout Voltage
The NCP139 dual−rail very low dropout voltage regulator
Because of two power supply inputs V and V
and
is using NMOS pass transistor for output voltage regulation
IN
BIAS
one V
regulator output, there are two Dropout voltages
from V voltage. All the low current internal control
OUT
IN
specified.
The first, the V Dropout voltage is the voltage
circuitry is powered from the V
voltage.
BIAS
The use of an NMOS pass transistor offers several
advantages in applications. Unlike PMOS topology devices,
the output capacitor has reduced impact on loop stability.
Vin to Vout operating voltage difference can be very low
compared with standard PMOS regulators in very low Vin
applications.
The NCP139 offers smooth monotonic start-up. The
controlled voltage rising limits the inrush current.
The Enable (EN) input is equipped with internal
hysteresis. NCP139 Voltage linear regulator Fixed and
Adjustable version is available.
IN
difference (V – V
) when V
OUT
starts to decrease by
IN
OUT
percent specified in the Electrical Characteristics table.
is high enough; specific value is published in the
V
BIAS
Electrical Characteristics table.
The second, V
dropout voltage is the voltage
BIAS
difference (V
– V
) when V and V
pins are
BIAS
OUT
IN
BIAS
joined together and V
starts to decrease.
OUT
Input and Output Capacitors
The device is designed to be stable for ceramic output
capacitors with Effective capacitance in the range from
10 mF to 22 mF. The device is also stable with multiple
capacitors in parallel, having the total effective capacitance
in the specified range.
Output Voltage Adjust
The required output voltage of Adjustable devices can be
adjusted from V
to 3.0 V using two external resistors.
REF
In applications where no low input supplies impedance
Typical application schematics is shown in Figure 5.
available (PCB inductance in V and/or V
inputs as
IN
BIAS
VBIAS
example), the recommended C = 1 mF and C
= 0.1 mF
IN
BIAS
C
NCP139 ADJ
or greater. Ceramic capacitors are recommended. For the
best performance all the capacitors should be connected to
the NCP139 respective pins directly in the device PCB
copper layer, not through vias having not negligible
impedance.
BIAS
OUT
FB
BIAS
VOUT
R1
R2
VIN
IN
μF
10
EN
C
IN
GND
When using small ceramic capacitor, their capacitance is
not constant but varies with applied DC biasing voltage,
temperature and tolerance. The effective capacitance can be
much lower than their nominal capacitance value, most
importantly in negative temperatures and higher LDO
output voltages. That is why the recommended Output
capacitor capacitance value is specified as Effective value in
the specific application conditions.
VEN
ǒ
Ǔ
VOUT + VREF 1 ) R1ńR2
Figure 5. Typical Application Schematics
It is recommended to keep the total serial resistance of
resistors (R1 + R2) no greater than 100 kW.
www.onsemi.com
6
NCP139
Enable Operation
Thermal Protection
The enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this data sheet. If the enable function is not to be used
Internal thermal shutdown (TSD) circuitry is provided to
protect the integrated circuit in the event that the maximum
junction temperature is exceeded. When TSD activated , the
regulator output turns off. When cooling down under the low
temperature threshold, device output is activated again. This
TSD feature is provided to prevent failures from accidental
overheating.
Activation of the thermal protection circuit indicates
excessive power dissipation or inadequate heatsinking. For
reliable operation, junction temperature should be limited to
+85°C maximum.
then the pin should be connected to V or V
.
IN
BIAS
Current Limitation
The internal Current Limitation circuitry allows the
device to supply the full 1 A nominal current and short time
current peaks up to 1.3 A but protects the device against
Current Overload or Short.
ORDERING INFORMATION
Nominal
Reference
Voltage
Output
Voltage
Device
Marking
AY
Option
Package
Shipping†
NCP139AFCT05ADJT2G
NCP139AFCTC05ADJT2G
ADJ
ADJ
0.5 V
0.5 V
Output Active Discharge
AY
Output Active Discharge,
Back Side Coating
NCP139AFCT06ADJT2G
NCP139AFCTC06ADJT2G
ADJ
ADJ
0.6 V
0.6 V
A6
A6
Output Active Discharge
Output Active Discharge,
Back Side Coating
WLCSP6
(Pb−Free)
NCP139AFCT100T2G
NCP139AFCT105T2G
NCP139AFCT110T2G
NCP139AFCTC110T2G
1.00 V
1.05 V
1.10 V
1.10 V
−
−
−
−
AK
AC
AJ
AJ
Output Active Discharge
Output Active Discharge
Output Active Discharge
5000 / Tape & Reel
Output Active Discharge,
Back Side Coating
NCP139AFCT120T2G
NCP139AFCT180T2G
1.20 V
1.80 V
−
−
AL
AZ
Output Active Discharge
Output Active Discharge
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe-
cifications Brochure, BRD8011/D.
To order other package and voltage variants, please contact your ON Semiconductor sales representative
www.onsemi.com
7
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
WLCSP6, 1.20x0.80
CASE 567MV
ISSUE B
SCALE 4:1
DATE 05 JUN 2018
E
A
NOTES:
B
D
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. COPLANARITY APPLIES TO SPHERICAL
CROWNS OF SOLDER BALLS.
PIN A1
REFERENCE
MILLIMETERS
2X
0.05
0.05
C
DIM
A
A1
A2
b
D
E
e
MIN
−−−
0.04
0.23 REF
0.24
1.20 BSC
0.80 BSC
0.40 BSC
MAX
0.33
0.08
2X
C
0.30
TOP VIEW
SIDE VIEW
A2
A
0.05
0.05
C
GENERIC
MARKING DIAGRAM*
C
SEATING
PLANE
C
e
NOTE 3
A1
XXM
XX = Specific Device Code
6X
b
e
M
= Month Code
0.05
0.03
C
C
A B
C
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
B
A
1
2
BOTTOM VIEW
RECOMMENDED
SOLDERING FOOTPRINT*
PACKAGE
OUTLINE
A1
6X
0.40
PITCH
0.20
0.40
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98AON06670G
WLCSP6, 1.20x0.80
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
ON Semiconductor Website: www.onsemi.com
◊
www.onsemi.com
相关型号:
©2020 ICPDF网 联系我们和版权申明