NCP502SQ15T2G [ONSEMI]
80 mA CMOS Low Iq Low-Dropout Voltage; 80毫安CMOS低Iq低压差型号: | NCP502SQ15T2G |
厂家: | ONSEMI |
描述: | 80 mA CMOS Low Iq Low-Dropout Voltage |
文件: | 总9页 (文件大小:174K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NCP502, NCV502
80 mA CMOS Low Iq,
Low-Dropout Voltage
Regulator
The NCP502 series of fixed output linear regulators are designed for
handheld communication equipment and portable battery powered
applications which require low quiescent. The NCP502 series features
an ultra−low quiescent current of 40 ꢀ A. Each device contains a
voltage reference unit, an error amplifier, a PMOS power transistor,
resistors for setting output voltage, current limit, and temperature limit
protection circuits.
The NCP502 has been designed to be used with low cost ceramic
capacitors. The device is housed in the micro−miniature SC70−5 and
TSOP−5 surface mount packages. Standard voltage versions are 1.5 V,
1.8 V, 2.5 V, 2.7 V, 2.8 V, 2.9 V, 3.0 V, 3.1 V, 3.3 V, 3.4 V, 3.5 V, 3.6 V,
3.7 V and 5.0 V. Other voltages are available in 100 mV steps.
http://onsemi.com
MARKING
DIAGRAM
5
4
SC70−5
SQ SUFFIX
CASE 419A
xxx MG
5
G
3
2
1
1
1
5
TSOP−5
(SOT23−5, SC59−5)
SN SUFFIX
xxx AYWG
5
G
Features
CASE 483
1
Low Quiescent Current of 40 ꢀ A Typical
Excellent Line and Load Regulation
Low Output Voltage Option
xxx = Specific Device Code
A
Y
W
M
G
= Assembly Location
= Year
= Work Week
= Date Code
Output Voltage Accuracy of 2.0%
Industrial Temperature Range of −40C to 85C,
= Pb−Free Package
NCV502, T = −40C to 125C
A
(Note: Microdot may be in either location)
NCP502: 1.3 V Enable Threshold High, 0.3 V Enable Threshold Low
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
PIN CONNECTIONS
V
1
2
5
V
out
in
These are Pb−Free Devices
GND
Typical Applications
Enable
3
4
N/C
Cellular Phones
Battery Powered Consumer Products
Hand−Held Instruments
Camcorders and Cameras
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
Battery or
Unregulated
Voltage
Vout
C2
1
2
3
5
4
+
C1
+
ON
OFF
This device contains 86 active transistors
Figure 1. Typical Application Diagram
Semiconductor Components Industries, LLC, 2013
1
Publication Order Number:
May, 2013 − Rev. 20
NCP502/D
NCP502, NCV502
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
Description
1
2
3
V
Positive power supply input voltage.
Power supply ground.
in
GND
Enable
This input is used to place the device into low−power standby. When this input is pulled low, the device is
disabled. If this function is not used, Enable should be connected to Vin.
4
5
N/C
No internal connection.
V
out
Regulated output voltage.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
V
Input Voltage
Enable Voltage
Output Voltage
V
in
12
Enable
−0.3 to V +0.3
V
in
V
out
−0.3 to V +0.3
V
in
Power Dissipation and Thermal Characteristics
Power Dissipation
P
Internally Limited
+150
W
C
C
D
Operating Junction Temperature
Operating Ambient Temperature
T
J
NCP502
NCV502
T
A
−40 to +85
−40 to +125
Storage Temperature
T
stg
−55 to +150
C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Latchup capability (85C) 100 mA DC with trigger voltage.
THERMAL CHARACTERISTICS
Rating
Symbol
Test Conditions
Value
Unit
2
Thermal Characteristics, TSOP−5 (Note 2)
Thermal Resistance, Junction−to−Air (Note 3)
R
1 oz Copper Thickness, 100 mm
C/W
ꢁ
JA
205
400
Thermal Resistance, Junction−to−Ambient, SC70−5
R
ꢁ
JA
W
C/W
NOTE: Single component mounted on a 80 x 80 x 15 mm FR4 PCB with stated copper head spreading area. Using the following
boundary conditions as stated in EIA/JESD 51−1, 2, 3, 7, 12.
2. True no connect. Printed circuit board traces are allowable.
3. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015.
Machine Model Method 200 V..
http://onsemi.com
2
NCP502, NCV502
ELECTRICAL CHARACTERISTICS
(V = V
+ 2.0 V, V
= V , C = 1.0 ꢀ F, C = 1.0 ꢀ F, T = 25C, unless otherwise noted.)
in
out(nom.)
enable
in
in
out
J
Characteristic
Output Voltage (TA = 25C, I = 10 mA) V = V (nom.) +1.0 V
Symbol
Min
Typ
Max
Unit
V
out
V
out
in
out
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
2.9 V
3.0 V
3.1 V
3.3 V
3.4 V
3.5 V
3.6 V
3.7 V
5.0 V
1.455
1.746
2.425
2.646
2.744
2.842
2.94
3.038
3.234
3.332
3.43
1.5
1.8
2.5
2.7
2.8
2.9
3.0
3.1
3.3
3.4
3.5
3.6
3.7
5.0
1.545
1.854
2.575
2.754
2.856
2.958
3.06
3.162
3.366
3.468
3.57
3.528
3.626
4.900
3.672
3.774
5.100
Output Voltage (TA = T
to T
, I = 10 mA) V = V (nom.)
V
out
V
low
high out
in
out
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
2.9 V
3.0 V
3.1 V
3.3 V
3.4 V
3.5 V
3.6 V
3.7 V
5.0 V
1.455
1.746
2.425
2.619
2.716
2.813
2.910
3.007
3.201
3.298
3.43
1.5
1.8
2.5
2.7
2.8
2.9
3.0
3.1
3.3
3.4
3.5
3.6
3.7
5.0
1.545
1.854
2.575
2.781
2.884
2.987
3.09
3.193
3.399
3.502
3.57
3.528
3.626
4.900
3.672
3.774
5.100
Line Regulation (V = V + 1.0 V to 12 V, I = 10 mA)
Reg
−
−
0.4
0.2
3.0
0.8
−
mV/V
mV/mA
mA
in
out
out
line
Load Regulation (I = 1.0 mA to 80 mA)
Reg
out
load
Output Current (V = (V at I = 80 mA) −3%)
I
80
180
out
out
out
o(nom.)
Dropout Voltage (T = T
to T
, I = 80 mA, Measured at V
V −V
in out
mV
A
low
high out
out
−3.0%)
1.5 V−1.7 V
1.8 V−2.4 V
2.5 V−2.6 V
2.7 V−2.9 V
3.0 V−4.0 V
4.1 V−5.0 V
NCV502 − 5.0 V
−
−
−
−
−
−
−
1500
1300
1000
850
850
600
1900
1700
1400
1300
1200
900
700
1100
Quiescent Current
(Enable Input = 0 V)
I
Q
ꢀ
A
−
−
0.1
40
1.0
90
(Enable Input = V , I = 1.0 mA to I
)
in out
o(nom.)
Output Short Circuit Current (V = 0 V)
I
90
−
200
55
500
−
mA
dB
out
out(max)
Ripple Rejection (f = 1.0 kHz, 15 mA)
RR
Output Voltage Noise (f = 100 Hz to 100 kHz)
V
−
180
−
ꢀ Vrms
V
n
Enable Input Threshold Voltage (NCP502)
V
th(en)
(Voltage Increasing, Output Turns On, Logic High)
(Voltage Decreasing, Output Turns Off, Logic Low)
1.3
−
−
−
−
0.3
Output Voltage Temperature Coefficient
T
C
−
100
−
ppm/C
4. Maximum package power dissipation limits must be observed.
T
*T
A
ꢁJA
J(max)
PD +
R
5. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
http://onsemi.com
3
NCP502, NCV502
45
45
40
35
30
25
20
15
V
V
= 5.0 V
= 3.0 V
V
OUT
= 3.0 V
IN
OUT
42.5
40
37.5
35
10
5
32.5
30
0
0
1
2
3
4
5
6
7
−60
−40
−20
0
20
40
60
80 100
V
IN
, INPUT VOLTAGE (V)
T, TEMPERATURE (C)
Figure 2. Quiescent Current versus Input Voltage
Figure 3. Quiescent Current versus Temperature
6
10
5
V
IN
= 4.0 V to 5.0 V
V
V
= 4.0 V
IN
ENABLE
5
4
= 0 to 4.0 V
0
60
40
20
0
C
= 1.0 ꢀ F
= 30 mA
OUT
I
OUT
3.0
2.0
I
= 30 mA
OUT
C
= 1.0 ꢀ F
OUT
1.0
0
−20
−40
0
10
20 30 40 50 60
70 80 90 100
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
t, TIME (ms)
t, TIME (ꢀ s)
Figure 4. Line Transient Response
Figure 5. Enable Response
60
30
0
70
60
50
40
100
50
0
C
= 1.0 ꢀ F
= 3.0 V
= 4.0 V
OUT
OUT
V
V
IN
V
V
= 4.5 V + 0.5 V
P−P
IN
= 3.0 V
OUT
30
20
I
= 30 mA
OUT
−50
C
= 1.0 ꢀ F
OUT
−100
0
50 100 150 200 250 300 350 400 450
0.01
0.1
1.0
FREQUENCY (kHz)
10
100
t, TIME (ꢀ s)
Figure 6. Load Transient Response
Figure 7. Ripple Rejection/Frequency
http://onsemi.com
4
NCP502, NCV502
2.995
V = 12 V
IN
I
= 10 mA
OUT
2.99
2.985
2.98
V
IN
= 4.0 V
2.975
2.97
2.965
2.96
−60
−40
−20
0
20
40
60
80
100
T, TEMPERATURE (C)
Figure 8. Output Voltage versus Temperature
3.5
3
C
C
= 1.0 ꢀ F
IN
= 1.0 ꢀ F
OUT
V
= V
ENABLE
IN
2.5
2
1.5
1
0.5
0
0
1
2
3
4
5
6
V
IN
, INPUT VOLTAGE (V)
Figure 9. Output Voltage versus Input Voltage
1200
1000
800
80 mA LOAD
600
40 mA LOAD
10 mA LOAD
400
200
0
−50 −25
0
25
50
75
100
125
T, TEMPERATURE (C)
Figure 10. Dropout Voltage versus Temperature
http://onsemi.com
5
NCP502, NCV502
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse technique such that the average
chip temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 3.0% below
its nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical over and undershoot response when input voltage
is excited with a given slope.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 160C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Maximum Power Dissipation
The maximum total dissipation for which the regulator
will operate within its specifications.
Quiescent Current
The quiescent current is the current which flows through
the ground when the LDO operates without a load on its
output: internal IC operation, bias, etc. When the LDO
becomes loaded, this term is called the Ground current. It is
actually the difference between the input current (measured
through the LDO input pin) and the output current.
Maximum Package Power Dissipation
The maximum power package dissipation is the power
dissipation level at which the junction temperature reaches
its maximum operating value, i.e. 125C. Depending on the
ambient power dissipation and thus the maximum available
output current.
APPLICATIONS INFORMATION
A typical application circuit for the NCP502 series is
shown in Figure 1, front page.
threshold are covered in the electrical specification section
of this data sheet. If the enable is not used then the pin should
be connected to V .
in
Input Decoupling (C1)
A 1.0 ꢀ F capacitor either ceramic or tantalum is
recommended and should be connected close to the NCP502
package. Higher values and lower ESR will improve the
overall line transient response. If large line or load transients
are not expected, then it is possible to operate the regulator
without the use of a capacitor.
Hints
Please be sure the Vin and GND lines are sufficiently
wide. When the impedance of these lines is high, there is a
chance to pick up noise or cause the regulator to
malfunction.
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
TDK capacitor: C2012X5R1C105K, or C1608X5R1A105K
Output Decoupling (C2)
The NCP502 is a stable regulator and does not require any
specific Equivalent Series Resistance (ESR) or a minimum
output current. Capacitors exhibiting ESRs ranging from a
few mꢂ up to 5.0 ꢂ can thus safely be used. The minimum
decoupling value is 1.0 ꢀ F and can be augmented to fulfill
stringent load transient requirements. The regulator accepts
ceramic chip capacitors as well as tantalum devices. Larger
values improve noise rejection and load regulation transient
response.
Thermal
As power across the NCP502 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material and also the ambient
temperature effect the rate of temperature rise for the part.
This is stating that when the NCP502 has good thermal
conductivity through the PCB, the junction temperature will
be relatively low with high power dissipation applications.
TDK capacitor: C2012X5R1C105K, C1608X5R1A105K,
or C3216X7R1C105K
Enable Operation
The enable pin will turn on the regulator when pulled high
and turn off the regulator when pulled low. These limits of
http://onsemi.com
6
NCP502, NCV502
The maximum dissipation the package can handle is
given by:
ƪ
ƫ
[
]
P
+ V * I
(I ) ) V * V
in
* I
tot
in gnd out
out out
or
T
*T
A
ꢁJA
J(max)
PD +
)
*
I
P
V
tot
gnd
out out
) I
R
V
+
inMAX
I
out
If junction temperature is not allowed above the
maximum 125C, then the NCP502 can dissipate up to
250 mW @ 25C.
The power dissipated by the NCP502 can be calculated
from the following equation:
If an 80 mA output current is needed then the ground
current from the data sheet is 40 ꢀ A. For an NCP502 (3.0 V),
the maximum input voltage will then be 6.12 V.
ꢃ
ORDERING INFORMATION
Nominal
†
Output Voltage
Device
NCP502SQ15T2G
NCP502SQ18T1G
NCP502SQ18T2G
NCP502SQ25T2G
NCP502SQ27T2G
NCP502SQ28T2G
NCP502SQ29T2G
NCP502SQ30T2G
NCP502SQ31T2G
NCP502SQ33T2G
NCP502SQ34T2G
NCP502SQ35T2G
NCP502SQ36T2G
NCP502SQ37T2G
NCP502SQ50T2G
NCP502SN28T1G
NCP502SN29T1G
NCP502SN30T1G
NCP502SN31T1G
NCP502SN33T1G
NCP502SN34T1G
NCP502SN35T1G
NCP502SN36T1G
NCP502SN37T1G
NCP502SN50T1G
NCV502SN50T1G*
Marking
LCC
Package
Shipping
1.5
1.8
LCD
2.5
2.7
2.8
2.9
3.0
3.1
3.3
3.4
3.5
3.6
3.7
5.0
2.8
2.9
3.0
3.1
3.3
3.4
3.5
3.6
3.7
5.0
5.0
LCE
LCF
LCG
LJI
SC70−5
(Pb−Free)
LCH
LJJ
3000 / Tape & Reel
LCI
LJK
LGO
LIU
LJQ
LCJ
LKD
LJN
LKE
LJO
LKF
LJK
LJ6
TSOP−5
(Pb−Free)
3000 / Tape & Reel
AC4
LKC
LKG
LKG
Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
http://onsemi.com
7
NCP502, NCV502
PACKAGE DIMENSIONS
SC−88A (SC−70−5/SOT−353)
SQ SUFFIX
CASE 419A−02
ISSUE L
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
G
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
5
4
3
−B−
S
INCHES
DIM MIN MAX
MILLIMETERS
MIN
1.80
1.15
0.80
0.10
MAX
2.20
1.35
1.10
0.30
1
2
A
B
C
D
G
H
J
0.071
0.045
0.031
0.004
0.087
0.053
0.043
0.012
0.026 BSC
0.65 BSC
M
M
B
D 5 PL
0.2 (0.008)
---
0.004
0.004
0.004
0.010
0.012
---
0.10
0.10
0.10
0.25
0.30
K
N
S
N
0.008 REF
0.20 REF
0.079
0.087
2.00
2.20
J
C
K
H
SOLDER FOOTPRINT
0.50
0.0197
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
mm
inches
ǒ
Ǔ
SCALE 20:1
http://onsemi.com
8
NCP502, NCV502
PACKAGE DIMENSIONS
TSOP−5
SN SUFFIX
CASE 483−02
ISSUE K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
NOTE 5
5X
D
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
0.20 C A B
2X
0.10
T
M
5
4
3
2X
0.20
T
B
S
1
2
K
B
A
DETAIL Z
G
A
MILLIMETERS
TOP VIEW
DIM
A
B
MIN
3.00 BSC
1.50 BSC
MAX
DETAIL Z
C
D
0.90
0.25
1.10
0.50
J
G
H
J
K
M
S
0.95 BSC
C
0.01
0.10
0.20
0
0.10
0.26
0.60
10
3.00
0.05
H
SEATING
PLANE
END VIEW
C
_
_
SIDE VIEW
2.50
SOLDERING FOOTPRINT*
1.9
0.074
0.95
0.037
2.4
0.094
1.0
0.039
0.7
0.028
mm
inches
ǒ
Ǔ
SCALE 10:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
NCP502/D
相关型号:
NCP502SQ25T1G
2.5V FIXED POSITIVE LDO REGULATOR, 1.4V DROPOUT, PDSO5, LEAD FREE, SC-88A, SOT-353, SC-70, 5 PIN
ROCHESTER
NCP502SQ27T1G
2.7V FIXED POSITIVE LDO REGULATOR, 1.3V DROPOUT, PDSO5, LEAD FREE, SC-88A, SOT-353, SC-70, 5 PIN
ROCHESTER
©2020 ICPDF网 联系我们和版权申明