NCP7812TG [ONSEMI]
1.0 A Positive Voltage Regulators;
| 型号： | NCP7812TG |
| 厂家： | 
ONSEMI |
| 描述： | 1.0 A Positive Voltage Regulators 局域网 输出元件 调节器 |
| 文件： | 总12页 (文件大小：144K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
NCP7800
1.0 A Positive Voltage
Regulators
The NCP7800 series consists of 3 pin, fixed output, positive linear
voltage regulators, suitable for a wide variety of applications. These
regulators are extremely rugged, incorporating internal current
limiting, thermal shutdown and safe-area compensation. With
adequate heat sinking they can deliver output currents in excess of
1.0 A. Designed as direct replacements for the popular MC7800
family, these products offer enhanced ESD protection.
http://onsemi.com
Features
• Output Current in Excess of 1.0 A
1
2
3
• No External Components Required
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting
TO−220−3
T SUFFIX
• Output Transistor Safe−Area Compensation
• Output Voltage Offered in 4% Tolerance
• Available in Standard 3−Lead Transistor Packages
• For Tighter Tolerances and Extended Operating Range Refer to MC7800
• Enhanced ESD Tolerance: HBM 4 kV (5 V and 8 V Options), 3 kV
(12 V and 15 V Options), and MM 400 V
CASE 221AB
PIN CONNECTIONS
Pin 1. Input
2. Ground
3. Output
• These are Pb−Free Devices
Heatsink surface
connected to Pin 2
NCP78XX
Input
Output
C **
MARKING
DIAGRAM
C *
in
0.33 mF
O
xx
A
= 05, 08, 12 or 15
= Assembly Location
78xxT
AWLYWWG
A common ground is required between the input and
the output voltages. The input voltage must remain
typically 2.0 V above the output voltage even during the
low point on the input ripple voltage.
WL, L = Wafer Lot
= Year
WW = Work Week
= Pb−Free Device
Y
G
XX
These two digits of the type number indicate
nominal voltage.
* C is required if regulator is located an appreciable
distance from power supply filter.
in
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
** C is not needed for stability; however,
O
it does improve transient response. Values of less
than 0.1 mF could cause instability.
Figure 1. Application Schematic
© Semiconductor Components Industries, LLC, 2010
1
Publication Order Number:
June, 2010 − Rev. 1
NCP7800/D
NCP7800
Figure 2. Simplified Block Diagram
Description
Table 1. PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
1
2
3
V
Positive Power Supply Input.
in
GND
Power Supply Ground; Device Substrate.
Regulated Output Voltage.
V
out
http://onsemi.com
2
NCP7800
Table 2. ABSOLUTE MAXIMUM RATINGS (Note 1)
Rating
Symbol
Value
−0.3 to 35
Internally Limited
150
Unit
V
Input Voltage Range
(for V : 5.0 − 15 V)
V
in
out
Power Dissipation
P
D
W
Maximum Junction Temperature
Storage Temperature Range
ESD Capability, Human Body Model (Note 2)
T
°C
°C
kV
J(max)
T
stg
−65 to +150
NCP7805, NCP7808
NCP7812, NCP7815
ESD
4
3
HBM
ESD Capability, Machine Model (Note 2)
ESD
400
V
MM
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per EIA/JESD22−A114
ESD Machine Model tested per EIA/JESD22−A115
Latchup Current Maximum Rating: ≤150 mA per JEDEC standard: JESD78
Table 3. THERMAL CHARACTERISTICS
Rating
Symbol
Value
Unit
Thermal Characteristics, TO−220−3 (Note 3)
Thermal Resistance, Junction−to−Case
Thermal Resistance, Junction−to−Air (Note 4)
°C/W
R
7.5
65
q
JC
JA
R
q
3. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
4. Value based on thermal measurement in a test socket.
Table 4. OPERATING RANGES (Note 5)
Rating
Symbol
Min
7.0
0
Max
35
Unit
V
Input Voltage (Note 6)
Junction Temperature
(for V : 5.0 − 15 V)
V
in
out
T
J
125
°C
5. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
6. Minimum V = 7.0 V or (V + V ), whichever is higher.
in
out
DO
http://onsemi.com
3
NCP7800
Table 5. ELECTRICAL CHARACTERISTICS (V = 10 V, I = 500 mA, T = 0°C to 125°C, unless otherwise noted) (Note 7)
in
O
J
NCP7805
Typ
Min
Max
Characteristic
Output Voltage (T = 25°C)
Symbol
Unit
Vdc
Vdc
V
O
O
4.8
5.0
5.2
J
Output Voltage (5.0 mA ≤ I ≤ 1.0 A, P ≤ 15 W)
V
O
D
7.0 Vdc ≤ V ≤ 20 Vdc
4.75
5.0
5.25
in
Line Regulation (T = 25°C)
Reg
mV
mV
J
line
7.5 Vdc ≤ V ≤ 20 Vdc
−
−
1.1
0.6
100
50
in
8.0 Vdc ≤ V ≤ 12 Vdc
in
Load Regulation (T = 25°C)
Reg
load
J
5.0 mA ≤ I ≤ 1.0 A
−
−
1.5
2.9
50
100
O
5.0 mA ≤ I ≤ 1.5 A
O
Quiescent Current (T = 25°C)
I
−
3.0
8
mA
mA
J
B
Quiescent Current Change
DI
B
7.0 Vdc ≤ V ≤ 25 Vdc
−
−
0.28
0.07
1.3
0.5
in
5.0 mA ≤ I ≤ 1.0 A
O
Ripple Rejection (Note 8)
RR
V − V
62
75
−
dB
8.0 Vdc ≤ V ≤ 18 Vdc, f = 120 Hz
in
Dropout Voltage (I = 1.0 A, T = 25°C) (Note 8)
−
−
2.0
6.8
−
−
Vdc
O
J
I
O
Output Noise Voltage (T = 25°C) (Note 8)
V
n
mV/V
O
J
10 Hz ≤ f ≤ 100 kHz
Output Resistance f = 1.0 kHz (Note 8)
r
−
−
2.2
0.3
−
−
mW
O
Short Circuit Current Limit (T = 25°C) (Note 8)
I
A
J
SC
V
in
= 35 Vdc
Peak Output Current (T = 25°C) (Note 8)
I
−
−
2.4
−
−
A
J
max
Average Temperature Coefficient of Output Voltage (Note 8)
TCV
0.13
mV/°C
O
7. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at
T = T = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
J
A
8. Value based on design and/or characterization.
http://onsemi.com
4
NCP7800
Table 6. ELECTRICAL CHARACTERISTICS (V = 14 V, I = 500 mA, T = 0°C to 125°C, unless otherwise noted) (Note 9)
in
O
J
NCP7808
Typ
Min
Max
Characteristic
Output Voltage (T = 25°C)
Symbol
Unit
Vdc
Vdc
V
O
O
7.68
8.0
8.32
J
Output Voltage (5.0 mA ≤ I ≤ 1.0 A, P ≤ 15 W)
V
O
D
10.5 Vdc ≤ V ≤ 23 Vdc
7.60
8.0
8.40
in
Line Regulation (T = 25°C)
Reg
mV
mV
J
line
10.5 Vdc ≤ V ≤ 25 Vdc
−
−
1.8
1.0
160
80
in
11.0 Vdc ≤ V ≤ 17 Vdc
in
Load Regulation (T = 25°C)
Reg
load
J
5.0 mA ≤ I ≤ 1.5 A
−
−
3.7
3.0
160
8.0
O
Quiescent Current (T = 25°C)
I
B
mA
mA
J
Quiescent Current Change
DI
B
10.5 Vdc ≤ V ≤ 25 Vdc
−
−
−
−
1.0
0.5
in
5.0 mA ≤ I ≤ 1.0 A
O
Ripple Rejection (Note 10)
RR
V − V
56
72
−
dB
11.5 Vdc ≤ V ≤ 21.5 Vdc, f = 120 Hz
in
Dropout Voltage (I = 1.0 A, T = 25°C) (Note 10)
−
−
2.0
6.8
−
−
Vdc
O
J
I
O
Output Noise Voltage (T = 25°C) (Note 10)
V
n
mV/V
O
J
10 Hz ≤ f ≤ 100 kHz
Output Resistance f = 1.0 kHz (Note 10)
r
−
−
2.7
0.3
−
−
mW
O
Short Circuit Current Limit (T = 25°C) (Note 10)
I
A
J
SC
V
in
= 35 Vdc
Peak Output Current (T = 25°C) (Note 10)
I
−
−
2.4
−
−
A
J
max
Average Temperature Coefficient of Output Voltage (Note 10)
TCV
0.24
mV/°C
O
9. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at
T = T = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
J
A
10.Value based on design and/or characterization.
http://onsemi.com
5
NCP7800
Table 7. ELECTRICAL CHARACTERISTICS (V = 19 V, I = 500 mA, T = 0°C to 125°C, unless otherwise noted) (Note 11)
in
O
J
NCP7812
Typ
Min
Max
Characteristic
Output Voltage (T = 25°C)
Symbol
Unit
Vdc
Vdc
V
O
O
11.52
12
12.48
J
Output Voltage (5.0 mA ≤ I ≤ 1.0 A, P ≤ 15 W)
V
O
D
14.5 Vdc ≤ V ≤ 27 Vdc
11.40
12
12.60
in
Line Regulation (T = 25°C)
Reg
mV
mV
J
line
14.5 Vdc ≤ V ≤ 30 Vdc
−
−
2.7
1.4
240
120
in
16 Vdc ≤ V ≤ 22 Vdc
in
Load Regulation (T = 25°C)
Reg
load
J
5.0 mA ≤ I ≤ 1.5 A
−
−
5.5
3.0
240
8.0
O
Quiescent Current (T = 25°C)
I
B
mA
mA
J
Quiescent Current Change
DI
B
14.5 Vdc ≤ V ≤ 30 Vdc
−
−
−
−
1.0
0.5
in
5.0 mA ≤ I ≤ 1.0 A
O
Ripple Rejection (Note 12)
RR
V − V
55
71
−
dB
15 Vdc ≤ V ≤ 25 Vdc, f = 120 Hz
in
Dropout Voltage (I = 1.0 A, T = 25°C) (Note 12)
−
−
2.0
6.8
−
−
Vdc
O
J
I
O
Output Noise Voltage (T = 25°C) (Note 12)
V
n
mV/V
O
J
10 Hz ≤ f ≤ 100 kHz
Output Resistance f = 1.0 kHz (Note 12)
r
−
−
3.6
0.3
−
−
mW
O
Short Circuit Current Limit (T = 25°C) (Note 12)
I
A
J
SC
V
in
= 35 Vdc
Peak Output Current (T = 25°C) (Note 12)
I
−
−
2.4
−
−
A
J
max
Average Temperature Coefficient of Output Voltage (Note 12)
TCV
0.47
mV/°C
O
11. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at
T = T = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
J
A
12.Value based on design and/or characterization.
http://onsemi.com
6
NCP7800
Table 8. ELECTRICAL CHARACTERISTICS (V = 23 V, I = 500 mA, T = 0°C to 125°C, unless otherwise noted) (Note 13)
in
O
J
NCP7815
Typ
Min
Max
Characteristic
Output Voltage (T = 25°C)
Symbol
Unit
Vdc
Vdc
V
O
O
14.40
15
15.60
J
Output Voltage (5.0 mA ≤ I ≤ 1.0 A, P ≤ 15 W)
V
O
D
17.5 Vdc ≤ V ≤ 30 Vdc
14.25
15
15.75
in
Line Regulation (T = 25°C)
Reg
mV
mV
J
line
17.9 Vdc ≤ V ≤ 30 Vdc
−
−
3.3
1.8
300
150
in
20 Vdc ≤ V ≤ 26 Vdc
in
Load Regulation (T = 25°C)
Reg
load
J
5.0 mA ≤ I ≤ 1.5 A
−
−
6.9
3.0
300
8.0
O
Quiescent Current (T = 25°C)
I
B
mA
mA
J
Quiescent Current Change
DI
B
17.5 Vdc ≤ V ≤ 30 Vdc
−
−
−
−
1.0
0.5
in
5.0 mA ≤ I ≤ 1.0 A
O
Ripple Rejection (Note 14)
RR
V − V
54
70
−
dB
18.5 Vdc ≤ V ≤ 28.5 Vdc, f = 120 Hz
in
Dropout Voltage (I = 1.0 A, T = 25°C) (Note 14)
−
−
2.0
6.8
−
−
Vdc
O
J
I
O
Output Noise Voltage (T = 25°C) (Note 14)
V
n
mV/V
O
J
10 Hz ≤ f ≤ 100 kHz
Output Resistance f = 1.0 kHz (Note 14)
r
−
−
4.7
0.3
−
−
mW
O
Short Circuit Current Limit (T = 25°C) (Note 14)
I
A
J
SC
V
in
= 35 Vdc
Peak Output Current (T = 25°C) (Note 14)
I
−
−
2.4
−
−
A
J
max
Average Temperature Coefficient of Output Voltage (Note 14)
TCV
0.42
mV/°C
O
13.Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at
T = T = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
J
A
14.Value based on design and/or characterization.
http://onsemi.com
7
NCP7800
TYPICAL CHARACTERISTICS
3.0
2.5
2.0
1.5
1.0
90
f = 120 Hz
= 20 mA
DV = 1.0 V(RMS)
I
O
in
T = 0°C
J
80
70
T = 25°C
J
T = 125°C
J
PART #ꢀ ꢁ V
in
NCP7805ꢁ= 10 V
NCP7808ꢁ= 14 V
NCP7812ꢁ= 19 V
NCP7815ꢁ= 23 V
60
50
0.5
0
0
5
10
15
20
25
30
35
40
4
6
8
10
12 14
16 18 20 22 24
V
in
− V , INPUT/OUTPUT VOLTAGE DIFFERENTIAL (V)
V , OUTPUT VOLTAGE (V)
O
out
Figure 3. Peak Output Current as a Function
of Input/Output Differential Voltage (NCP7805)
Figure 4. Ripple Rejection as a Function of
Output Voltage
5.10
5.05
5.00
4.95
4.90
80
70
60
50
V
I
= 20 V
= 5.0 mA
in
O
V
= 8.0 V to 18 V
= 500 mA
= 25°C
in
I
O
T
A
40
30
4.85
4.80
−60
−20
20
60
100
140
180
0.01
0.1
1
10
T , JUNCTION TEMPERATURE (°C)
J
f, FREQUENCY (kHz)
Figure 5. Ripple Rejection as a Function of
Frequency (NCP7805)
Figure 6. Output Voltage as a Function of
Junction Temperature (NCP7805)
10
6
V
V
= 10 V
= 5.0 V
in
O
5
4
3
2
I = 20 mA
L
1
f = 120 Hz
1
0
I
O
= 500 mA
C = 0 mF
L
0.1
4
6
8
10
12 14
16 18 20 22 24
−50
−25
0
25
50
75
100
125
V , OUTPUT VOLTAGE (V)
O
T , JUNCTION TEMPERATURE (°C)
J
Figure 7. Output Impedance as a Function of
Output Voltage
Figure 8. Quiescent Current as a Function of
Temperature (NCP7805)
http://onsemi.com
8
NCP7800
APPLICATIONS INFORMATION
Design Considerations
The NCP7800 Series of fixed voltage regulators are
designed with Thermal Overload Protection that shuts down
the circuit when subjected to an excessive power overload
condition, Internal Short Circuit Protection that limits the
maximum current the circuit will pass, and Output Transistor
Safe−Area Compensation that reduces the output short circuit
current as the voltage across the pass transistor is increased.
In many low current applications, compensation
capacitors are not required. However, it is recommended
that the regulator input be bypassed with a capacitor if the
regulator is connected to the power supply filter with long
wire lengths, or if the output load capacitance is large. An
input bypass capacitor should be selected to provide good
high−frequency characteristics to insure stable operation
under all load conditions. A 0.33 mF or larger tantalum,
mylar, or other capacitor having low internal impedance at
high frequencies should be chosen. The bypass capacitor
should be mounted with the shortest possible leads directly
across the regulators input terminals. Normally good
construction techniques should be used to minimize ground
loops and lead resistance drops since the regulator has no
external sense lead.
NCP7805
Input
Output
NCP7805
R
0.33 mF
Constant
Current to
Grounded
Load
Input
I
O
-
+
0.33 mF
0.1 mF
The NCP7800 regulators can also be used as a current source when
connected as above. In order to minimize dissipation the NCP7805 is
chosen in this application. Resistor R determines the current as follows:
10 k
1.0 k
MC34072V
5.0ꢂV
I
+
) I
O
B
R
V
V
= 7.0 V to 20 V
≥ V + 2.0 V
O
IN
O
I ^ 3.2 mA over line and load changes.
B
The addition of an operational amplifier allows adjustment to higher or
intermediate values while retaining regulation characteristics. The
minimum voltage obtainable with this arrangement is 2.0 V greater than the
regulator voltage.
For example, a 1.0 A current source would require R to be a 5.0 W,
10 W resistor and the output voltage compliance would be the input
voltage less 7.0 V.
Figure 9. Current Regulator
Figure 10. Adjustable Output Regulator
MJ2955
or Equiv.
MJ2955 or Equiv.
R
R
R
SC
Source
Source
Input
Input
0.33 mF
0.33 mF
R
2N6049
or Equiv.
NCP78XX
Output
R
NCP78XX
≥ 10 mF
1.0 mF
1.0 mF
Output
≥ 10 mF
1.0 mF
XX = 2 digits of type number indicating voltage.
XX = 2 digits of type number indicating voltage.
The circuit of Figure 11 can be modified to provide supply protection
against short circuits by adding a short circuit sense resistor, R , and an
The NCP7800 series can be current boosted with a PNP transistor. The
MJ2955 provides current to 5.0 A. Resistor R in conjunction with the V
BE
SC
of the PNP determines when the pass transistor begins conducting; this
circuit is not short circuit proof. Input/output differential voltage minimum is
increased by V of the pass transistor.
additional PNP transistor. The current sensing PNP must be able to handle
the short circuit current of the three-terminal regulator. Therefore, a
four-ampere plastic power transistor is specified.
BE
Figure 11. Current Boost Regulator
Figure 12. Short Circuit Protection
http://onsemi.com
9
NCP7800
2.5
20
16
q
q
T
= 7.5°C/W
= 65°C/W
= 150°C
JC
JA
I
O
= 1.0 A
q
= 0°C/W
HS
2.0
1.5
J(max)
I
I
= 500 mA
= 200 mA
O
O
I
q
= 5°C/W
= 20 mA
HS
12
8.0
4.0
0
O
I
O
= 0 mA
1.0
0.5
q
= 15°C/W
HS
DV = 2% of V
O
O
No Heatsink
25
0
-50
-25
0
50
75
100
125
150
-75
-50
-25
0
25
50
75
100
125
T , AMBIENT TEMPERATURE (°C)
A
T , JUNCTION TEMPERATURE (°C)
J
Figure 13. Worst Case Power Dissipation vs.
Figure 14. Input Output Differential as a Function
of Junction Temperature
Ambient Temperature (TO−220)
Protection Diode
several milliseconds. In this case a damage may occur to the
regulator.
To protect the regulator the external bypass diode
connected between output and input is recommended. The
protection diode should be rated for sufficient peak current.
The NCP7800 Series has internal low impedance (about
1 W) diode path that normally does not require protection
when used in the typical regulator applications. The path
connects between output and input and it can withstand a
peak surge current of about 5 A for a reasonable time
(several milliseconds). Normal cycling of Vin cannot
generate a current surge of this magnitude for too long time
since output capacitor discharges from output to input and
follows input voltage therefore the magnitude of reverse
current is not so high. However, when Vin is shorted or
crowbarred to ground and output cap is too large and
moreover if higher voltage option is used then the peak of
reverse current is much higher than 5 A and lasts more than
Protection Diode
NCP78XX
Input
Cin
Output
Cout
Figure 15. Protection Diode Placement
http://onsemi.com
10
NCP7800
DEFINITIONS
Line Regulation − The change in output voltage for a
Quiescent Current − That part of the input current that is
not delivered to the load.
Output Noise Voltage − The rms ac voltage at the output,
with constant load and no input ripple, measured over a
specified frequency range.
change in the input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that the average chip temperature is not significantly
affected.
Load Regulation − The change in output voltage for a
change in load current at constant chip temperature.
Maximum Power Dissipation − The maximum total
device dissipation for which the regulator will operate
within specifications.
Long Term Stability − Output voltage stability under
accelerated life test conditions with the maximum rated
voltage listed in the devices’ electrical characteristics and
maximum power dissipation.
ORDERING INFORMATION
Operating
Temperature Range
Device
NCP7805TG
Nominal Voltage
Package
Shipping
5.0 V
T = 0°C to +125°C
J
TO−220
(Pb−Free)
50 Units / Rail
NCP7808TG
NCP7812TG
NCP7815TG
8.0 V
12 V
15 V
T = 0°C to +125°C
TO−220
50 Units / Rail
50 Units / Rail
50 Units / Rail
J
(Pb−Free)
T = 0°C to +125°C
J
TO−220
(Pb−Free)
T = 0°C to +125°C
J
TO−220
(Pb−Free)
http://onsemi.com
11
NCP7800
PACKAGE DIMENSIONS
TO−220, SINGLE GAUGE
T SUFFIX
CASE 221AB−01
ISSUE O
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
SEATING
PLANE
−T−
C
S
B
F
T
INCHES
DIM MIN MAX
MILLIMETERS
4
1
MIN
14.48
9.66
4.07
0.64
3.61
2.42
2.80
0.46
12.70
1.15
4.83
2.54
2.04
0.508
5.97
0.00
1.15
---
MAX
15.75
10.28
4.82
0.88
3.73
2.66
3.93
0.64
14.27
1.52
5.33
3.04
2.79
1.39
6.47
1.27
---
A
B
C
D
F
0.570
0.380
0.160
0.025
0.142
0.095
0.110
0.018
0.500
0.045
0.190
0.100
0.080
0.020
0.235
0.000
0.045
---
0.620
0.405
0.190
0.035
0.147
0.105
0.155
0.025
0.562
0.060
0.210
0.120
0.110
0.055
0.255
0.050
---
A
K
Q
Z
2
3
U
H
G
H
J
K
L
N
Q
R
S
T
L
R
J
V
G
U
V
Z
D
0.080
2.04
N
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
NCP7800/D
相关型号：
©2020 ICPDF网 联系我们和版权申明