NCS21674 [ONSEMI]
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad;型号: | NCS21674 |
厂家: | ONSEMI |
描述: | Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad |
文件: | 总16页 (文件大小:873K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
www.onsemi.com
Current-Shunt Monitors,
40 V Common Mode,
Unidirectional, Single, Dual,
Quad
MARKING
DIAGRAMS
5
XXAYWG
1
G
TSOP−5
CASE 483
NCS21673, NCV21673,
NCS21674, NCV21674,
NCS21675, NCV21675
8
XXXX
AYW
G
Micro8
CASE 846A−02
The NCS21673, NCS21674, and NCS21675 are a series of current
sense amplifiers offered in gains of 20, 50, 100, and 200 V/V. These
parts can measure voltage across shunts at common mode voltages
from −0.1 V to 40 V, independent of supply voltage. This helps
measuring of fast transients and allows the same type of part to be used
for high side and low side current sensing. These devices can operate
from a single 2.7 V to 5.5 V power supply. With a −3 dB BW of up to
350 kHz and a Slew Rate of 2 V/ms typical , the fast detection of
current changes is ensured. These parts are available in SOT23−5,
Micro8, and TSSOP−14 packages. The multichannel versions (dual
and quad) make current sensing in multiple points of a system both
space and cost effective.
1
14
14
XX
ALYWG
G
1
TSSOP−14 WB
CASE 948G
1
XX
A
L
= Specific Device Code
= Assembly Location
= Wafer Lot
Y
= Year
W
G
= Work Week
= Pb−Free Package
Features
• Wide Common Mode Input Range: −0.1 V to 40 V
• Supply Voltage Range: 2.7 V to 5.5 V
• Low Offset Voltage: 100 mV
• Low Offset Drift: 1 mV/°C max
• Low Gain Error: 1% max
• Low Current Consumption: 300 mA max per channel
• NCV Prefix for Automotive Grade 1 and Other Applications
Requiring Unique Site and Control Change Requirements;
AEC−Q100 Qualified and PPAP Capable
(Note: Microdot may be in either location)
PIN CONNECTIONS
See pin connections on page 2 of this data sheet.
ORDERING INFORMATION
See detailed ordering and shipping information on page 3 of
this data sheet.
• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
Applications
• High−Side Current Sensing
• Low−Side Current Sensing
• Power Management
• Automotive
© Semiconductor Components Industries, LLC, 2021
1
Publication Order Number:
August, 2021 − Rev. 0
NCS21673/D
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
Supply
Supply
Load
RSHUNT
0.01 μF
to 0.1 μF
VS
NCS21673
R1
R3
IN−
−
Output
OUT
+
IN+
R4
R2
GND
V
OUT
= (I
x R
) * GAIN
LOAD
SHUNT
Figure 1. Example Application Schematic of High−Side Current Sensing
PIN CONNECTIONS
OUT 1
IN− 1
IN+ 1
GND
1
2
3
4
8
7
6
5
V
S
OUT
GND
IN+
1
2
3
V
S
5
4
−
OUT 2
IN− 2
IN+ 2
+
−
+
IN−
Single Channel
Dual Channel
1
2
3
4
5
6
7
OUT 1
IN− 1
IN+ 1
14
OUT 4
IN− 4
IN+ 4
−
13
12
11
10
9
−
+
+
GND
V
S
IN+ 3
IN− 3
OUT 3
IN+ 2
IN− 2
+
+
−
−
8
OUT 2
Quad Channel
Figure 2. Pin Connections
www.onsemi.com
2
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
ORDERING INFORMATION
Device
Channels
Package
Gain
OPN
Marking
Shipping
Industrial and Consumer
NCS21673
NCS21674
NCS21675
Single
TSOP−5
20
50
NCS21673SN2G020T1G**
NCS21673SN2G050T1G**
NCS21673SN2G100T1G**
NCS21673SN2G200T1G**
NCS21674DMG020R2G**
NCS21674DMG050R2G**
NCS21674DMG100R2G**
NCS21674DMG200R2G
NCS21675DTBG020R2G**
NCS21675DTBG050R2G**
NCS21675DTBG100R2G**
NCS21675DTBG200R2G**
TBD
TBD
TBD
TBD
G020
G050
G100
G200
TBD
TBD
TBD
TBD
Tape and Reel
3000/reel
100
200
20
Dual
Micro8
Tape and Reel
4000/reel
50
100
200
20
Quad
TSSOP−14
Tape and Reel
2500/reel
50
100
200
Automotive Qualified
NCV21673*
NCV21674*
NCV21675*
Single
TSOP−5
Micro8
20
50
NCV21673SN2G020T1G**
NCV21673SN2G050T1G**
NCV21673SN2G100T1G**
NCV21673SN2G200T1G**
NCV21674DMG020R2G**
NCV21674DMG050R2G**
NCV21674DMG100R2G**
NCV21674DMG200R2G**
NCV21675DTBG020R2G**
NCV21675DTBG050R2G**
NCV21675DTBG100R2G**
NCV21675DTBG200R2G**
TBD
TBD
TBD
TBD
G020
G050
G100
G200
TBD
TBD
TBD
TBD
Tape and Reel
3000/reel
100
200
20
Dual
Tape and Reel
4000/reel
50
100
200
20
Quad
TSSOP−14
Tape and Reel
2500/reel
50
100
200
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable
**In Development
www.onsemi.com
3
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
MAXIMUM RATINGS
Parameter
Symbol
Rating
−0.3 to 5.5
42
Unit
V
Supply Voltage (Note 1)
Analog Inputs
V
S
Differential (V )−(V ) (Note 2)
V V
IN+, IN−
V
IN+
IN−
Common−Mode (Note 2)
−0.3 to +42
Output (Note 2)
V
GND−0.3 to (V ) +0.3
V
mA
°C
°C
V
OUT
s
Input Current into Any Pin (Note 2)
Maximum Junction Temperature
Storage Temperature Range
I
10
+150
IN
T
J(max)
T
STG
−65 to +150
2000
ESD Capability, Human Body Model (Note 3)
Charged Device Model (Note 3)
Latch−up Current (Note 4)
HBM
CDM
1000
V
100
mA
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTICS, RECOMMENDED OPERATING RANGES and/or APPLICATION INFORMATION for safe
operating parameters
2. Input voltage at any pin may exceed the voltage shown if current at that pin is limited to 10 mA
3. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per JEDEC standard JS−001−2017
ESD Charged Device Model tested per JEDEC standard JS−002−2014
4. Latch−up Current tested per JEDEC standard: JESD78E
THERMAL CHARACTERISTICS
Parameter
Symbol
Package
TSOP−5 / SOT23−5
Micro8 / MSOP−8
TSSOP−14
Value
210
Unit
Thermal Resistance, Junction−to−Air (Notes 5, 6)
q
°C/W
JA
195
TBD
5. Refer to ELECTRICAL CHARACTERISTICS, RECOMMENDED OPERATING RANGES and/or APPLICATION INFORMATION for safe
operating parameters
2
2
6. Values based on copper area of 645 mm (or 1 in ) of 1 oz copper thickness and FR4 PCB substrate
RECOMMENDED OPERATING RANGES
Parameter
Ambient Temperature
Symbol
Conditions
NCS prefix
Min
−40
−40
–0.1
2.7
Max
125
150*
40
Unit
T
A
°C
NCV prefix
Common Mode Input Voltage
Supply Voltage
V
CM
Ta = −40°C to +125°C
Ta = −40°C to +125°C
Ta = 0°C to +85°C
V
V
V
S
5.5
1.8
5.5
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
*During operation at Ta = 150°C, also the limitation for junction temperature (Tj(max) = 150°C) has to be considered.
www.onsemi.com
4
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
ELECTRICAL CHARACTERISTICS
At T = +25°C, V
= (V ) – (V ) V = 5 V, V
= 12 V, unless otherwise noted. Boldface limits apply over the specified
A
SENSE
IN+
IN− .;
S
IN+
temperature range, T = –40°C to 125°C unless otherwise noted, guaranteed by characterization and/or design.
A
Parameter
Symbol
Conditions
Min
Typ
100
100
100
100
Max
Unit
Input
Common Mode Rejection
Ratio
CMRR
V
V
= −0.1 V to 40 V,
G = 20
G = 50
84
84
84
84
84
84
84
84
dB
IN+
SENSE
= 0 mV
G = 100
G = 200
Input Offset Voltage
V
T = 25°C, V
= 12 V
= 0 V
G = 20
G = 50
100
100
100
100
25
500
500
500
500
TBD
TBD
TBD
210
1
mV
OS
A
IN+
G = 100
G = 200
G = 20
T = 25°C, V
A
IN+
G = 50
25
G = 100
G = 200
25
25
Input Offset Voltage Drift
vs. Temperature
dV /dT
OS
T = −40°C to +125°C
A
0.2
mV/°C
mV/V
mA
Power Supply Rejection
Ratio
PSRR
V
V
= 2.7 V to 5.5 V,
SENSE
8
+ 40
S
= 10 mV
Input Bias Current
I
V
V
= 0 V
1
IB
IN+
IN+
IN+
= 12 V
100
15
Input Offset Current
I
IO
V
V
= 12 V,
mA
= 10 mV
SENSE
Output
Gain
G
G = 20
G = 50
G = 100
G = 200
20
50
V/V
100
200
0.1
Gain Error
T = 25°C
A
%
T = −40°C to +125°C
A
+ 1
Gain Error vs Temperature
Nonlinearity Error
T = −40°C to +125°C
1.5
0.01
1
20
ppm/°C
%
A
Maximum Capacitive Load
Settling Time to 1%
Voltage Output
C
No sustained oscillation
nF
L
5
ms
Output Voltage High,
V
− V
0.02
V
V
R = 10 kW to GND, T = 25°C
S
OH
L
A
Swing from V Supply Rail
S
R = 10 kW to GND,
0.03
L
T = −40°C to 125°C
A
Output Voltage Low,
Swing from GND
V
OL
− GND
0.0005
R = 10 kW to GND, T = 25°C
L
A
R = 10 kW to GND,
0.005
L
T = −40°C to 125°C
A
www.onsemi.com
5
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
ELECTRICAL CHARACTERISTICS (continued)
At T = +25°C, V = (V ) – (V ) V = 5 V, V = 12 V, unless otherwise noted. Boldface limits apply over the specified
IN+
A
SENSE
IN+
IN− .;
S
temperature range, T = –40°C to 125°C unless otherwise noted, guaranteed by characterization and/or design.
A
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Frequency Response
Bandwidth (f
)
BW
C = 25 pF
L
G = 20
G = 50
350
210
150
105
2
kHz
−3dB
G = 100
G = 200
Slew Rate
SR
V/ms
Noise
Voltage Noise Density
e
n
G = 50 or higher
G = 20
40
nV/√Hz
TBD
Power Supply
Quiescent Current per
Channel
I
Q
T = 25°C
195
260
mA
A
T = −40°C to +125°C
A
300
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
6
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
TYPICAL CHARACTERISTICS (T = 25°C, VS = 5 V, and VIN+ = 12 V unless otherwise noted)
A
Figure 3. Input Offset Production Distribution G200
Figure 4. Offset Voltage vs. Temperature
Figure 5. CMRR Production Distribution G200
Figure 6. CMRR vs. Temperature
Figure 7. Gain Error Production Distribution G200
Figure 8. Gain Error vs. Temperature
www.onsemi.com
7
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
TYPICAL CHARACTERISTICS (T = 25°C, VS = 5 V, and VIN+ = 12 V unless otherwise noted) (continued)
A
Figure 10. Power Supply Rejection Ration
vs. Frequency
Figure 9. Gain vs. Frequency
Figure 12. Output High Swing vs. Output
Current
Figure 11. Common Mode Rejection Ratio
vs. Frequency
Figure 14. Input Bias Current vs. Common−Mode
Figure 13. Output Low Swing vs. Output Current
Voltage
www.onsemi.com
8
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
TYPICAL CHARACTERISTICS (T = 25°C, VS = 5 V, and VIN+ = 12 V unless otherwise noted) (continued)
A
Figure 15. Input Bias Current vs. Temperature
Figure 16. Quiescent Current vs. Temperature
Figure 18. 0.1−Hz to 10−Hz Voltage Noise
(Referred−to−Input)
Figure 17. Input−Referred Voltage Noise
vs. Frequency
Figure 20. Common−Mode Voltage Transient
Figure 19. Input Signal Step response
Response
www.onsemi.com
9
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
TYPICAL CHARACTERISTICS (T = 25°C, VS = 5 V, and VIN+ = 12 V unless otherwise noted) (continued)
A
Figure 21. Inverting Differential Input Overload
Figure 22. Noninverting Differential Input Overload
Figure 24. Brownout Recovery
Figure 23. Start−Up Response
Figure 25. Output Impedance vs. Frequency
Figure 26. Channel Separation vs. Frequency
www.onsemi.com
10
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
TYPICAL CHARACTERISTICS (T = 25°C, VS = 5 V, and VIN+ = 12 V unless otherwise noted) (continued)
A
Figure 27. Output Voltage vs. Common−Mode
Voltage
www.onsemi.com
11
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
APPLICATION INFORMATION
Current Sensing Techniques
Selecting the Shunt Resistor
NCS(V)21673, NCS(V)21674, and NCS(V)21675 are
current sense amplifiers featuring a wide common mode
voltage range that spans from −0.1 V to 40 V independent of
the supply voltage. These amplifiers can be configured for
low−side and high−side current sensing.
The desired accuracy of the current measurement
determines the precision, shunt size, and the resistor value.
The larger the resistor value, the more accurate the
measurement possible, but a large resistor value also results
in greater current loss.
For the most accurate measurements, use four−terminal
current sense resistors. They provide two terminals for the
current path in the application circuit, and a second pair for
the voltage detection path of the sense amplifier. This
technique is also known as Kelvin Sensing. This insures that
the voltage measured by the sense amplifier is the actual
voltage across the resistor and does not include the small
resistance of a combined connection. When using
non−Kelvin shunts, follow manufacturer recommendations
on how to lay out the sensing traces closely.
Unidirectional Operation
These current sense amplifiers monitor unidirectional
current flow. In unidirectional current sensing, the measured
load current always flows in the same direction. Common
applications for unidirectional operation include power
supplies and load current monitoring. In this configuration,
the IN+ pin should be connected to the high side of the sense
resistor, while the IN− pin should be connected to the low
side of the sense resistor.
Input Filtering
Gain Options
As shunt resistors decrease in value, shunt inductance can
significantly affect frequency response. At values below
1 mW, the shunt inductance causes a zero in the transfer
function that often results in corner frequencies in the low
100’s of kHz. This inductance increases the amplitude of
high frequency spike transient events on the current sensing
line that can overload the front end of any shunt current
sensing IC. This problem must be solved by the external
filtering at the input of the amplifier. Note that all current
sensing IC’s are vulnerable to this problem, regardless of
manufacturer claims. Filtering is required at the input of the
device to resolve this problem, even if the spike frequencies
are above the rated −3 dB bandwidth of the device.
Ideally, select the capacitor to exactly match the time
constant of the shunt resistor and its inductance;
alternatively, select the capacitor to provide a pole below
that point. Make the input filter time constant equal to or
larger than the shunt and its inductance time constant:
The gain is set by integrated, precision, ratio−matched
resistors. These current sense amplifiers are available in gain
options of 20 V/V, 50 V/V, 100 V/V, and 200 V/V. Adding
external resistors to adjust the gain can contribute to the
overall system error and is not recommended for multiple
reasons. First, the series resistors mismatch increase the
overall gain error and temperature coefficient, and lower the
CMRR. Second, the IIB flowing through the external
resistors change the differential voltage seen by the opamp’s
input. Last but not least, while the internal resistors are well
matched in terms of ratio, they have a high tolerance in their
absolute value so the resulting gain value may not match the
expectations.
Shutdown
While the NCS21673/4/5 series do not include a
shutdown feature, a simple MOSFET, power switch, or logic
gate can be used to switch off power and eliminate quiescent
current. Note that the input pins connected to the shunt
resistor will always have a current flow via the input and
feedback resistors (total resistance of each leg always is
approx. 400 kW). Also note that when powered, the shunt
input pins will exhibit the specified and well−matched bias
current. The shunt input pins support the rated common
mode voltage even when the power is not applied.
LSHUNT
v RFILTCFILT
RSHUNT
While this time constant can be the product of any R
FILT
and C
values, the designer needs to take into account that
resistors are connected in series with the internal
FILT
the R
FILT
feedback resistors R3 and R4, hence changing the
amplifier’s overall gain. Also, the opamp’s input currents
(IIB) create a voltage drop across the filtering resistors,
which is added to the differential voltage seen by the
opamp’s inputs and modifies the output value. A good
practice is to keep the filtering resistors in the range of a few
ohms then size the filtering capacitor accordingly.
www.onsemi.com
12
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
PACKAGE DIMENSIONS
TSOP−5
CASE 483
ISSUE M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
NOTE 5
5X
D
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
0.20 C A B
2X
0.10
T
M
5
4
3
2X
0.20
T
B
S
1
2
K
B
A
DETAIL Z
G
A
MILLIMETERS
TOP VIEW
DIM
A
B
C
D
MIN
2.85
1.35
0.90
0.25
MAX
3.15
1.65
1.10
0.50
DETAIL Z
J
G
H
J
K
M
S
0.95 BSC
C
0.01
0.10
0.20
0
0.10
0.26
0.60
10
3.00
0.05
H
SEATING
PLANE
END VIEW
C
_
_
SIDE VIEW
2.50
SOLDERING FOOTPRINT*
1.9
0.074
0.95
0.037
2.4
0.094
1.0
0.039
0.7
0.028
mm
inches
ǒ
Ǔ
SCALE 10:1
*For additional information on our Pb−Free strategy
and soldering details, please download the
onsemi Soldering and Mounting
Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
13
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
PACKAGE DIMENSIONS
Micro8t
CASE 846A−02
ISSUE J
D
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.
H
E
E
MILLIMETERS
INCHES
NOM
−−
0.003
0.013
0.007
0.118
DIM
A
A1
b
c
D
E
MIN
−−
NOM
−−
MAX
MIN
−−
MAX
0.043
0.006
0.016
0.009
0.122
0.122
PIN 1 ID
e
1.10
0.15
0.40
0.23
3.10
3.10
b 8 PL
0.05
0.25
0.13
2.90
2.90
0.08
0.002
0.010
0.005
0.114
0.114
0.33
M
S
S
0.08 (0.003)
T B
A
0.18
3.00
3.00
0.118
e
L
0.65 BSC
0.55
4.90
0.026 BSC
0.021
0.193
SEATING
PLANE
0.40
4.75
0.70
5.05
0.016
0.187
0.028
0.199
−T−
H
E
A
0.038 (0.0015)
L
A1
c
RECOMMENDED
SOLDERING FOOTPRINT*
8X
8X
0.48
0.80
5.25
0.65
PITCH
DIMENSION: MILLIMETERS
*For additional information on our Pb−Free strategy
and soldering details, please download the
onsemi Soldering and Mounting
Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
14
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
PACKAGE DIMENSIONS
TSSOP−14 WB
CASE 948G
ISSUE C
NOTES:
14X K REF
1. DIMENSIONING AND TOLERANCING PER
M
S
S
V
ANSI Y14.5M, 1982.
0.10 (0.004)
T U
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
S
0.15 (0.006) T U
N
0.25 (0.010)
14
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
8
2X L/2
M
B
L
N
−U−
PIN 1
IDENT.
F
7
1
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
DETAIL E
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
S
K
0.15 (0.006) T U
A
−V−
MILLIMETERS
DIM MIN MAX
INCHES
MIN MAX
K1
A
B
C
D
F
G
H
J
4.90
4.30
−−−
0.05
0.50
5.10 0.193 0.200
4.50 0.169 0.177
J J1
1.20
−−− 0.047
0.15 0.002 0.006
0.75 0.020 0.030
SECTION N−N
0.65 BSC
0.026 BSC
0.60 0.020 0.024
0.20 0.004 0.008
0.16 0.004 0.006
0.30 0.007 0.012
0.25 0.007 0.010
0.50
0.09
0.09
0.19
J1
K
−W−
C
K1 0.19
L
M
6.40 BSC
0.252 BSC
0.10 (0.004)
0
8
0
8
_
_
_
_
SEATING
PLANE
−T−
H
G
DETAIL E
D
SOLDERING FOOTPRINT
7.06
1
0.65
PITCH
01.34X6
14X
1.26
DIMENSIONS: MILLIMETERS
www.onsemi.com
15
NCS21673, NCV21673, NCS21674, NCV21674, NCS21675, NCV21675
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
onsemi Website: www.onsemi.com
◊
www.onsemi.com
相关型号:
NCS21674DMG020R2G
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad
ONSEMI
NCS21674DMG050R2G
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad
ONSEMI
NCS21674DMG100R2G
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad
ONSEMI
NCS21674DMG200R2G
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad
ONSEMI
NCS21675DTBG020R2G
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad
ONSEMI
NCS21675DTBG050R2G
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad
ONSEMI
NCS21675DTBG100R2G
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad
ONSEMI
NCS21675DTBG200R2G
Current-Shunt Monitors, 40 V Common Mode, Unidirectional, Single, Dual, Quad
ONSEMI
NCS21801SN2T1G
Precision Operational Amplifier, 10µV, Zero-Drift, 1.8V to 5.5V Supply, 1.5 MHz
ONSEMI
NCS21801SQ3T2G
Precision Operational Amplifier, 10µV, Zero-Drift, 1.8V to 5.5V Supply, 1.5 MHz
ONSEMI
©2020 ICPDF网 联系我们和版权申明