NCV8606MN25T2G
更新时间:2024-09-18 12:05:50
品牌:ONSEMI
描述:500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection
NCV8606MN25T2G 概述
500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection 500毫安,低IGND , CMOS LDO稳压器,带/不带使能和增强的ESD保护
NCV8606MN25T2G 数据手册
通过下载NCV8606MN25T2G数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载NCV8605, NCV8606
500 mA, Low IGND, CMOS
LDO Regulator with/without
Enable and with Enhanced
ESD Protection
http://onsemi.com
MARKING
The NCV8605/NCV8606 provide in excess of 500 mA of output
current at fixed voltage options or an adjustable output voltage from
5.0 V down to 1.25 V. These devices are designed for space constrained
and portable battery powered applications and offer additional features
such as high PSRR, low noise operation, short circuit and thermal
protection. The devices are designed to be used with low cost ceramic
capacitors and are packaged in the DFN6 3x3.3. NCV8605 is designed
without enable pin, NCV8606 is designed with enable pin.
DIAGRAM
V860x
zzz
1
DFN6, 3x3.3
MN SUFFIX
CASE 506AX
AYWWG
G
Features
• Output Voltage Options:
x
zzz
= 5 or 6
= ADJ, 150, 180, 250, 280,
300, 330, 500
= Assembly Location
= Year
= Work Week
Adjustable, 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V
• Adjustable Output by External Resistors from 5.0 V down to 1.25 V
A
Y
WW
G
• Current Limit 675 mA
• Low I
(Independent of Load)
= Pb−Free Package
GND
• $1.5% Output Voltage Tolerance Over All Operating Conditions
(Adjustable)
(Note: Microdot may be in either location)
• $2% Output Voltage Tolerance Over All Operating Conditions
(Fixed)
NCV8605 PIN CONNECTIONS
DFN6 3x3.3mm
• NCV8605 Fixed is Direct Replacement LP8345
• Typical Noise Voltage of 50 mV without a Bypass Capacitor
rms
V
in
V
in
1
2
3
6
5
4
• Enhanced ESD Ratings: 4 kV Human Body Mode (HBM)
400 V Machine Model (MM)
SENSE/ADJ
GND
NC
GND
• NCV Prefix for Automotive and Other Applications Requiring Site
and Change Controls
V
out
• These are Pb−Free Devices
(Top View)
Typical Applications
• Hard Disk Drivers
NCV8606 PIN CONNECTIONS
DFN6 3x3.3mm
• Notebook Computers
• Battery Power Electronics
• Portable Instrumentation
V
V
in
1
2
3
6
5
4
in
SENSE/ADJ
GND
EN
GND
V
in
V
out
V
in
V
out
V
out
NCV8605
(Fixed)
C
in
C
out
(Top View)
SENSE
GND
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
Figure 1. NCV8605 Typical Application Circuit for Fixed
Version (1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V)
© Semiconductor Components Industries, LLC, 2010
1
Publication Order Number:
May, 2010 − Rev. 0
NCV8605/D
NCV8605, NCV8606
V
in
V
out
V
in
V
out
NCV8606
(Fixed)
C
in
C
out
EN
SENSE
GND
Figure 2. NCV8606 Typical Application Circuit for Fixed Version (1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V)
V
in
V
out
V
in
V
out
V
in
V
out
V
in
V
out
NCV8605
(Adjustable)
ADJ
NCV8606
(Adjustable)
C
C
in
in
C
C
out
R
R
out
1
2
R
R
1
2
EN
ADJ
GND
GND
Figure 3. NCV8605 Typical Application Circuit for
Figure 4. NCV8606 Typical Application Circuit for
Adjustable Version (1.25 V < Vout v 5.0 V)
Adjustable Version (1.25 V < Vout v 5.0 V)
V
in
V
out
V
in
V
out
V
in
V
out
V
in
V
out
NCV8605
(Adjustable)
ADJ
NCV8606
(Adjustable)
C
C
in
in
C
C
out
out
EN
ADJ
GND
GND
Figure 5. NCV8605 Typical Application Circuit for
Adjustable Version (Vout = 1.25 V)
Figure 6. NCV8606 Typical Application Circuit for
Adjustable Version (Vout = 1.25 V)
V
in
V
out
V
in
V
out
Adjustable
Adjustable
Version Only
Version Only
SENSE/ADJ
SENSE/ADJ
+
−
+
−
Driver with
Current Limit
Driver with
Current Limit
Thermal
Shutdown
Thermal
Shutdown
V
ref
V
ref
EN
GND
GND
Fixed Version Only
Fixed Version Only
Figure 7. NCV8605 Simplified Block
Diagram
Figure 8. NCV8606 Simplified Block
Diagram
http://onsemi.com
2
NCV8605, NCV8606
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
Description
1
2
3
V
Positive Power Supply Input*
in
GND
Power Supply Ground
NC/EN
NCV8605: This Pin is Not Connected
NCV8606: This Pin is Enable Input, Active HIGH
4
5
V
out
Regulated Output Voltage
SENSE/ADJ
Output Voltage Sense Input
Fixed Version: Connect Directly to Output Capacitor
Adjustable Version: Connect to Middle Point of External Resistor Divider
6
V
in
Positive Power Supply Input*
EPAD
GND
Exposed Pad is Connected to Ground
*Pins 1 and 6 must be connected together externally for output current full range operation
ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
V
Input Voltage Range (Note 1)
Chip Enable Voltage Range (NCV8606 only)
Output Voltage Range
V
in
−0.3 to 6.5
−0.3 to 6.5
−0.3 to 6.5
−0.3 to 6.5
V
EN
V
V
out
V
Output Voltage/Sense Input Range, SENSE/ADJ
V
ADJ
V
ESD Capability
Human Body Model
Machine Model
ESD
4000
400
V
Maximum Junction Temperature
Storage Temperature Range
T
150
°C
°C
J(MAX)
T
−65 to 150
STG
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
NOTE: This device series contains ESD Protection and exceeds the following tests:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Machine Model tested per AEC− 150 mA per JEDEC standard: JESD78Q100−003 (EIA/JESD22−A115)
Latchup Current Maximum Rating: v 150 mA per JEDEC standard: JESD78.
1. Minimum V = (V + V ) or 1.5 V, whichever is higher.
in
out
DO
THERMAL CHARACTERISTICS
Rating
Symbol
Value
75
Unit
°C/W
°C/W
Thermal Resistance, Junction−to−Ambient (Note 2)
R
q
JA
Thermal Resistance, Junction−to−Case
R
18
Y
JC
2
2. Soldered on 645 mm , 1 oz copper area, FR4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe
Operating Area.
OPERATING RANGES (Note 3)
Rating
Symbol
Value
Unit
V
Input Voltage (Note 4)
Output Current (Notes 5 and 6)
Junction Temperature
V
in
1.5 to 6.0
0 to 675
I
mA
°C
out
T
J
−40 to 150
−40 to 125
Ambient Temperature
T
A
°C
3. Refer to Electrical Characteristics and Application Information for Safe Operating Area.
4. Minimum V = (V + V ) or 1.5 V, whichever is higher.
in
out
DO
5. Minimum limit valid for fixed versions only. For more details refer to Application Information Section.
6. Maximum limit for V = V − 10%.
out
out(nom)
http://onsemi.com
3
NCV8605, NCV8606
ELECTRICAL CHARACTERISTICS
V
in
= (V + 0.5 V) or 1.5 V, whichever is higher, C = 1 mF, C = 1 mF, for typical values T = 25°C, for min/max values T = −40°C to
out
in
out
A
A
85°C; unless otherwise noted. (Notes 9 and 10)
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
Output voltage (Adjustable Version)
V
out
= 1.75 V to 6 V
= 1 mA to 500 mA
V
out
1.231
(−1.5%)
1.250
1.269
(+1.5%)
V
in
I
Output voltage (Fixed Versions)
1.5 V
1.8 V
2.5 V
2.8 V
3.0 V
3.3 V
5.0 V
V
out
= (V + 0.5 V) to 6 V
V
out
1.470
1.764
2.450
2.744
2.940
3.234
4.900
(−2%)
1.5
1.8
2.5
2.8
3.0
3.3
5.0
1.530
1.836
2.550
2.856
3.060
3.366
5.100
(+2%)
V
in
out
I
= 1 mA to 500 mA
Line regulation
Load regulation
V
= (V + 0.5 V) to 6 V, I = 1 mA
Reg
−
−
4
10
30
mV
mV
mV
in
out
out
line
I
= 1 mA to 500 mA
Reg
10
out
load
Dropout voltage (Adjustable Version)
(Note 9)
V
= V − V
V
DO
DO
in
out
V
= 1.25 V
−
450
470
out
I
= 500 mA
out
Dropout voltage (Fixed Version)
V
= V − (V − 0.1 V)
V
DO
mV
DO
in
out
1.5 V
1.8 V
2.5 V
2.8 V
3.0 V
3.3 V
5.0 V
I
= 500 mA
−
−
−
−
−
−
−
290
250
200
190
180
170
150
360
300
250
240
230
220
200
out
V
out
= 0 V to 90% V
out(nom)
Disable Current (NCV8606 Only) (Note 10)
Ground Current
V
= 0 V
I
−
0.1
145
−
1
180
−
mA
mA
mA
mA
V
EN
DIS
I
= 1 mA to 500 mA
I
−
out
GND
Current Limit (Note 11)
V
out
= V
− 10 %
I
LIM
675
700
out(nom)
Output Short Circuit Current
V
out
= 0 V
I
1000
1350
SC
Enable Input Threshold Voltage
(NCV8606 Only)
Voltage Increasing, Logic High
Voltage Decreasing, Logic Low
V
th(EN)
High
Low
0.9
−
−
−
−
0.4
Turn−on Time (Note 11)
V
= 0 V to (V + 0.5 V) or 1.75 V,
t
on
ms
in
out
1.25 V whichever is higher
−
−
−
−
−
−
−
−
6
6
−
−
−
−
−
−
−
−
1.5 V
1.8 V
2.5 V
2.8 V
3.0 V
3.3 V
5.0 V
V
= 0 V to 90% of V
out out(nom)
7
8
10
12
15
30
Enable Time (NCV8606 Only) (Note 11)
V
EN
= From 0 V to V
t
EN
ms
in
1.25 V
1.5 V
1.8 V
2.5 V
2.8 V
3.0 V
3.3 V
5.0 V
−
−
−
−
−
−
−
−
12
12
13
16
18
19
20
30
−
−
−
−
−
−
−
−
7. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area.
8. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at T = T = 25°C. Low
J
A
duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
9. Maximum dropout voltage is limited to minimum input voltage V = 1.7 V recommended for guaranteed operation at maximum output
in
current.
10.Refer to application information section.
11. Values based on design and/or characterization.
http://onsemi.com
4
NCV8605, NCV8606
ELECTRICAL CHARACTERISTICS
V
in
= (V + 0.5 V) or 1.5 V, whichever is higher, C = 1 mF, C = 1 mF, for typical values T = 25°C, for min/max values T = −40°C to
out
in
out
A
A
85°C; unless otherwise noted. (Notes 9 and 10)
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
Power Supply Ripple Rejection (Note 11)
I
= 500 mA
PSRR
dB
out
V
= 1.25 V
out
V
− V = 1 V
in
out
f = 120 Hz, 0.5 V
−
−
−
62
55
40
−
−
−
PP
PP
PP
f = 1 kHz, 0.5 V
f = 10 kHz, 0.5 V
Output Noise Voltage (Note 11)
f = 10 Hz to 100 kHz, V = 1.25 V
V
−
−
−
50
175
10
−
−
−
mV
rms
out
n
Thermal Shutdown Temperature (Note 11)
Thermal Shutdown Hysteresis (Note 11)
T
SD
T
SH
°C
°C
7. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area.
8. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at T = T = 25°C. Low
J
A
duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
9. Maximum dropout voltage is limited to minimum input voltage V = 1.7 V recommended for guaranteed operation at maximum output
in
current.
10.Refer to application information section.
11. Values based on design and/or characterization.
http://onsemi.com
5
NCV8605, NCV8606
TYPICAL CHARACTERISTICS
1.267
1.264
1.261
1.258
1.255
1.252
1.249
1.246
1.243
1.240
1.237
1.234
1.231
2.55
V
= 1.25 V
= 1 mA
V
= 2.5 V
= 1 mA
out
out
2.54
2.53
2.52
2.51
2.50
2.49
2.48
2.47
2.46
2.45
I
I
out
out
V
= V + 0.5 V = 1.75 V
out
in
V
in
= V + 0.5 V = 3.0 V
out
V
in
= 6.0 V
V
in
= 6.0 V
−40 −20
0
20
40
60
80
100 120 140
−40 −20
0
20
40
60
80 100 120 140
T , AMBIENT TEMPERATURE (°C)
A
T , AMBIENT TEMPERATURE (°C)
A
Figure 9. Output Voltage vs. Temperature
(Vout = 1.25 V)
Figure 10. Output Voltage vs. Temperature
(Vout = 2.5 V)
300
270
240
210
180
150
120
90
5.10
5.08
5.06
5.04
5.02
5.00
4.98
4.96
4.94
4.92
4.90
V
= 5.0 V
= 1 mA
V
out
= 2.5 V
out
I
out
I
= 500 mA
= 300 mA
V
= V + 0.5 V = 5.5 V
out
out
in
I
out
V
in
= 6.0 V
I
= 150 mA
out
60
30
0
−40 −20
0
20
40
60
80
100 120 140
−40 −20
0
20
40
60
80 100
120 140
T , AMBIENT TEMPERATURE (°C)
A
T , AMBIENT TEMPERATURE (°C)
A
Figure 11. Output Voltage vs. Temperature
(Vout = 5.0 V)
Figure 12. Dropout Voltage vs. Temperature
(Vout = 2.5 V)
200
180
160
140
120
100
80
180
170
160
150
140
130
120
110
100
90
V
= V + 0.5 V
out
V
out
= 5.0 V
in
I
= 500 mA
out
V
= 5.0 V
= 2.5 V
out
I
= 500 mA
= 300 mA
out
I
out
V
out
I
= 150 mA
out
60
V
out
= 1.25 V
40
20
0
80
−40 −20
0
20
40
60
80
100 120 140
−40 −20
0
20
40
60
80
100 120 140
T , AMBIENT TEMPERATURE (°C)
A
T , AMBIENT TEMPERATURE (°C)
A
Figure 13. Dropout Voltage vs. Temperature
(Vout = 5.0 V)
Figure 14. Ground Current vs. Temperature
http://onsemi.com
6
NCV8605, NCV8606
TYPICAL CHARACTERISTICS
80
70
60
50
40
30
1600
1400
1200
1000
800
V
out
= 1.25 V
V
= 6.0 V
in
I
= 500 mA
out
I
= 1mA
out
V
in
= 1.75 V
V
= 1.25 V
= 2.25 V
out
600
20
10
0
V
in
C
= 1.0 mF
out
400
T = 25°C
A
200
−40 −20
0
20
40
60
80
100 120 140
10
100
1000
f, FREQUENCY (Hz)
10000
100000
T , AMBIENT TEMPERATURE (°C)
A
Figure 15. Short Circuit Current Limit vs.
Temperature (Vout = 1.25 V)
Figure 16. PSRR vs. Frequency (Vout = 1.25 V)
1600
1400
1200
1000
800
600
400
200
0
80
70
60
50
40
30
20
10
0
V
C
= V + 0.5 V = 1.75 V
out
V = 47 mV
in
n
rms
= C = 1.0 mF
in
out
I
= 500 mA
out
T = 25°C
A
I
= 1mA
out
I
= 500 mA
out
V
= 2.5 V
= 3.5 V
out
V
in
C
= 1.0 mF
out
T = 25°C
A
10
100
1000
f, FREQUENCY (Hz)
10000
100000
10
100
1000
10000
100000
f, FREQUENCY (Hz)
Figure 17. PSRR vs. Frequency (Vout = 2.5 V)
Figure 18. Noise Density vs. Frequency
(Vout = 1.25 V)
2500
2000
1500
1000
500
V = 70 mV
V
C
= V + 0.5 V = 3.0 V
n
rms
in
out
V
out
200 mV/div
= C = 1.0 mF
in
out
I
= 500 mA
out
T = 25°C
A
V
= 3.0 V
= 2.5 V
in
V
out
C
= 10 mF
out
t
= t = 1 ms
fall
rise
T = 25°C
A
I
out
500 mA/div
0
10
100
1000
f, FREQUENCY (Hz)
10000
100000
TIME (40 ms/div)
Figure 19. Noise Density vs. Frequency
(Vout = 2.5 V)
Figure 20. Load Transient (Vout = 2.5 V)
http://onsemi.com
7
NCV8605, NCV8606
TYPICAL CHARACTERISTICS
V
out
V
out
100 mV/div
1 V/div
V
= 2.5 V
= 0 mA
= 10 mF
out
V
I
= 2.5 V
= 500 mA
I
in
out
C
out
out
C
= 10 mF
out
t
= t = 1 ms
rise
fall
4.0 V
T = 25°C
A
V
= 3.0 V
= 1 ms
in
V
V
in
1 V/div
in
t
rise
3.0 V
500 mV/div
T = 25°C
A
TIME (20 ms/div)
TIME (10 ms/div)
Figure 21. Line Transient (Vout = 2.5 V)
Figure 22. Startup Transient (Vout = 2.5 V)
http://onsemi.com
8
NCV8605, NCV8606
DEFINITIONS
General
current are kept constant during the measurement. Results
All measurements are performed using short pulse low
duty cycle techniques to maintain junction temperature as
close as possible to ambient temperature.
are expressed in mV or nV / √Hz.
rms
Turn−on and Turn−off Times
Turn−on Time is time difference measured during
power−up of the device from the moment when input
voltage reaches 90% of its operating value to the moment
when output voltage reaches 90% of its nominal value at
specific output current or resistive load.
Turn−off Time is time difference measured during
power−down of the device from the moment when input
voltage drops to 10% of its operating value to the moment
when output voltage drops to 10% of its nominal value at
specific output current or resistive load.
Line Regulation
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse techniques such that the
average junction temperature is not significantly affected.
Load Regulation
The change in output voltage for a change in output load
current at a constant temperature.
Dropout Voltage
Enable and Disable Times
The input to output differential at which the regulator
output no longer maintains regulation against further
reductions in input voltage. Measured when the output drops
100 mV below its nominal value. The junction temperature,
load current, and minimum input supply requirements affect
the dropout level.
Enable Time is time difference measured during
power−up of the device from the moment when enable
voltage reaches 90% of input voltage operating value to the
moment when output voltage reaches 90% of its nominal
value at specific output current or resistive load.
Disable Time is time difference measured during
power−down of the device from the moment when enable
voltage drops to 10% of input voltage operating value to the
moment when output voltage drops to 10% of its nominal
value at specific output current or resistive load.
Ground and Disable Currents
Ground Current is the current that flows through the
ground pin when the regulator operates without a load on its
output (I
). This consists of internal IC operation, bias,
GND
etc. It is actually the difference between the input current
(measured through the LDO input pin) and the output load
current. If the regulator has an input pin that reduces its
internal bias and shuts off the output (enable/disable
Line Transient Response
Typical output voltage overshoot and undershoot response
when the input voltage is excited with a given slope.
function), this term is called the disable current (I ).
Load Transient Response
DIS
Typical output voltage overshoot and undershoot
response when the output current is excited with a given
slope between no−load and full−load conditions.
Current Limit and Short Circuit Current Limit
Current Limit is value of output current by which output
voltage drops by 10% with respect to its nominal value.
Short Circuit Current Limit is output current value
measured with output of the regulator shorted to ground.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 175°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
PSRR
Power Supply Rejection Ratio is defined as ratio of output
voltage and input voltage ripple. It is measured in decibels
(dB).
Maximum Package Power Dissipation
The power dissipation level at which the junction
temperature reaches its maximum operating value.
Output Noise Voltage
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output load
http://onsemi.com
9
NCV8605, NCV8606
APPLICATIONS INFORMATION
Noise Decoupling
The NCV8605/NCV8606 regulator is self*protected
with internal thermal shutdown and internal current limit.
Typical application circuits are shown in Figures 1 to 4.
The NCV8605/NCV8606 is a low noise regulator and
needs no external noise reduction capacitor. Unlike other
low noise regulators which require an external capacitor and
have slow startup times, the NCV8605/NCV8606 operates
without a noise reduction capacitor, has a typical 8 ms
Input Decoupling (Cin)
A ceramic or tantalum 1.0 mF capacitor is recommended
and should be connected close to the NCV8605/NCV8606
package. Higher capacitance and lower ESR will improve
the overall line transient response.
turn−on time and achieves a 50 mV overall noise level
between 10 Hz and 100 kHz.
rms
Enable Operation (NCV8606 Only)
Output Decoupling (Cout
)
The enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this data sheet. The turn−on/turn−off transient
voltage being supplied to the enable pin should exceed a
slew rate of 10 mV/ms to ensure correct operation. If the
enable function is not to be used then the pin should be
The NCV8605/NCV8606 is a stable component and does
not require a minimum Equivalent Series Resistance (ESR)
for the output capacitor. The minimum output decoupling
value is 1.0 mF and can be augmented to fulfill stringent load
transient requirements. The regulator works with ceramic
chip capacitors as well as tantalum devices. Larger values
improve noise rejection and load regulation transient
response. Typical characteristics were measured with
Murata ceramic capacitors. GRM219R71E105K (1 mF,
25 V, X7R, 0805) and GRM21BR71A106K (10 mF, 10 V,
X7R, 0805).
connected to V .
in
Output Voltage Adjust
The output voltage can be adjusted from 1 times (Figure
4) to 4 times (Figure 3) the typical 1.250 V regulation
voltage via the use of resistors between the output and the
ADJ input. The output voltage and resistors are chosen using
Equation 1 and Equation 2.
No−Load Regulation Considerations
The NCV8605/NCV8606 adjustable regulator will
operate properly under conditions where the only load
current is through the resistor divider that sets the output
R
1
) ǒI
1Ǔ
R
+ 1.250ǒ1 ) Ǔ
(eq. 1)
V
out
ADJ
R
2
voltage. However,
in
the
case
where
the
R
1
R
^
NCV8605/NCV8606 is configured to provide a 1.250 V
output, there is no resistor divider. If the part is enabled
under no−load conditions, leakage current through the pass
transistor at junction temperatures above 85°C can approach
several microamps, especially as junction temperature
approaches 150°C. If this leakage current is not directed into
a load, the output voltage will rise up to a level
approximately 20 mV above nominal.
2
V
(eq. 2)
out
* 1
1.25
Input bias current I
is typically less than 150 nA.
ADJ
Choose R arbitrarily to minimize errors due to the bias
1
current and to minimize noise contribution to the output
voltage. Use Equation 2 to find the required value for R .
2
Thermal
The NCV8605/ NCV8606 contains an overshoot clamp
circuit to improve transient response during a load current
step release. When output voltage exceeds the nominal by
approximately 20 mV, this circuit becomes active and
clamps the output from further voltage increase. Tying the
As power in the NCV8605/NCV8606 increases, it might
become necessary to provide some thermal relief. The
maximum power dissipation supported by the device is
dependent upon board design and layout. Mounting pad
configuration on the PCB, the board material, and the
ambient temperature affect the rate of junction temperature
rise for the part. When the NCV8605/NCV8606 has good
thermal conductivity through the PCB, the junction
temperature will be relatively low with high power
ENABLE pin to V (NCV8606 only) will ensure that the
in
part is active whenever the supply voltage is present, thus
guaranteeing that the clamp circuit is active whenever
leakage current is present.
When the NCV8606 adjustable regulator is disabled, the
overshoot clamp circuit becomes inactive and the pass
applications.
The
maximum
dissipation
the
NCV8605/NCV8606 can handle is given by:
transistor leakage will charge any capacitance on V . If no
out
ƪT
Aƫ
* T
load is present, the output can charge up to within a few
J(MAX)
R
(eq. 3)
P
+
D(MAX)
millivolts of V . In most applications, the load will present
in
QJA
some impedance to V such that the output voltage will be
out
Since T is not recommended to exceed 125°C (T
then the NCV8605/NCV8606 soldered on 645 mm , 1 oz
copper area, FR4 can dissipate up to 1.3 W when the ambient
),
J
J(MAX)
2
inherently clamped at a safe level. A minimum load of
10 mA is recommended.
Unlike LP8345, for NCV8605/606 fixed voltage versions
there is no limitation for minimum load current.
http://onsemi.com
10
NCV8605, NCV8606
Hints
V
in
temperature (T ) is 25°C. See Figure 23 for R
versus
qJA
A
and GND printed circuit board traces should be as
PCB area.
wide as possible. When the impedance of these traces is
high, there is a chance to pick up noise or cause the regulator
to malfunction. Place external components, especially the
output capacitor, as close as possible to the
NCV8605/NCV8606, and make traces as short as possible.
The power dissipated by the NCV8605/NCV8606 can be
calculated from the following equations:
inǒIGND
Ǔ) I ǒV
in
outǓ
* V
(eq. 4)
P
[ V
@I
out
D
OUT
or
) ǒV
outǓ
I
P
out
D(MAX)
I
(eq. 5)
V
[
in(MAX)
250
) I
out
GND
200
150
100
50
FR4 = 1.0 oz
FR4 = 2.0 oz
0
0
200
400
600
800
2
COPPER AREA (mm )
Figure 23. Thermal Resistance vs. Copper Area
http://onsemi.com
11
NCV8605, NCV8606
ORDERING INFORMATION
Nominal Output
Voltage (V)
†
Device
Marking
Package
Shipping
NCV8605MNADJT2G
ADJ
1.5
1.8
2.5
2.8
3.0
3.3
5.0
ADJ
1.5
1.8
2.5
2.8
3.0
3.3
5.0
V8605
ADJ
DFN6
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
3000 / Tape & Reel
(Pb−Free)
NCV8605MN15T2G
NCV8605MN18T2G
NCV8605MN25T2G
NCV8605MN28T2G
NCV8605MN30T2G
NCV8605MN33T2G
NCV8605MN50T2G
NCV8606MNADJT2G
NCV8606MN15T2G
NCV8606MN18T2G
NCV8606MN25T2G
NCV8606MN28T2G
NCV8606MN30T2G
NCV8606MN33T2G
NCV8606MN50T2G
V8605
150
DFN6
(Pb−Free)
V8605
180
DFN6
(Pb−Free)
V8605
250
DFN6
(Pb−Free)
V8605
280
DFN6
(Pb−Free)
V8605
300
DFN6
(Pb−Free)
V8605
330
DFN6
(Pb−Free)
V8605
500
DFN6
(Pb−Free)
V8606
ADJ
DFN6
(Pb−Free)
V8606
150
DFN6
(Pb−Free)
V8606
180
DFN6
(Pb−Free)
V8606
250
DFN6
(Pb−Free)
V8606
280
DFN6
(Pb−Free)
V8606
300
DFN6
(Pb−Free)
V8606
330
DFN6
(Pb−Free)
V8606
500
DFN6
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
12
NCV8605, NCV8606
PACKAGE DIMENSIONS
DFN6 3x3.3 MM, 0.95 PITCH
CASE 506AX−01
ISSUE O
DATE 20 JAN 2006
A
NOTES:
D
1. DIMENSIONS AND TOLERANCING PER ASME
Y14.5M, 1994.
B
E
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.25 AND 0.30 mm
FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED PAD
AS WELL AS THE TERMINALS.
PIN 1
REFERENCE
MILLIMETERS
DIM MIN
0.80
A1 0.00
NOM MAX
A
−−−
−−−
0.90
0.05
2X
0.15
C
A3
b
0.20 REF
−−−
3.00 BSC
−−−
3.30 BSC
−−−
0.30
0.40
2.10
1.30
2X
D
D2 1.90
E
E2 1.10
0.15
C
TOP VIEW
e
K
L
0.95 BSC
−−−
−−−
0.10
C
C
0.20
0.40
−−−
0.60
0.15
A
L1 0.00
−−−
6X
SEATING
PLANE
0.08
(A3)
C
SIDE VIEW
D2
A1
SOLDERING FOOTPRINT*
4X
e
3.60
6X L
6X
0.50
K
1.35
1
6
3
4
1
E2
0.95
PITCH
2.15
6X L1
6X b (NOTE 3)
0.10 C A B
0.05
6X
0.83
BOTTOM VIEW
DIMENSIONS: MILLIMETERS
C
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operat-
ing parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor
the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associ-
ated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/
Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
NCV8605/D
NCV8606MN25T2G 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
NCV8606MN28T2G | ONSEMI | 500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection | 获取价格 | |
NCV8606MN30T2G | ONSEMI | 500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection | 获取价格 | |
NCV8606MN33T2G | ONSEMI | 500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection | 获取价格 | |
NCV8606MN50T2G | ONSEMI | 500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection | 获取价格 | |
NCV8606MNADJT2G | ONSEMI | 500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection | 获取价格 | |
NCV8612 | ONSEMI | Ultra-Low Iq Automotive System Power Supply IC Power Saving Triple-Output Linear Regulator | 获取价格 | |
NCV8612B | ONSEMI | Ultra-Low Iq Automotive System Power Supply IC Power Saving Triple-Output Linear Regulator | 获取价格 | |
NCV8612BMNR2G | ONSEMI | Ultra-Low Iq Automotive System Power Supply IC Power Saving Triple-Output Linear Regulator | 获取价格 | |
NCV8612MNR2G | ONSEMI | Ultra-Low Iq Automotive System Power Supply IC Power Saving Triple-Output Linear Regulator | 获取价格 | |
NCV8613 | ONSEMI | Ultra-Low Iq Automotive System Power Supply IC Power Saving Triple-Output Linear Regulator | 获取价格 |
NCV8606MN25T2G 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6