70013 [OSRAM]
BACKlight LED Modules;
OSRAM GMBH 
Product Information Bulletin
BACKlight
LED Modules
• Uniform illumination of channel letter signs
• Long life: up to 100,000 hours depending on color
• OSRAM Power TOPLED® allows high luminous flux
• 120° viewing angle per LED
• Low profile (<5mm) allows installation where space
is limited
• Each module has 8 movable coupons connected
with wires
• Minimal heat generation
• Wire interconnects allow flexible mounting.
Total length can be varied from 0.8 ft. to 1.8 ft.
• Mounting hole allows easy installation by screw
or snap-in spacers
• Three modules can be connected head to tail. Up to six
modules in series with power fed to the center of the strip
• Many modules can be connected in parallel (limited only
by power source capacity and UL considerations)
• Listed in UL Sign Accessory Manual (SAM)
The OSRAM SYLVANIA BACKlight – an innovative
alternative to neon and other conventional lighting.
• Conformally coated to protect against moisture and
condensation (IP22)
BACKlight modules offer alternatives to traditional neon
sources. The main advantages of LED BACKlight over neon
or cold cathode sources are reduced manufacturing costs,
durability, reduced maintenance costs, and small size.
• Available as a system with matching OPTOTRONIC®
power supplies (Literature Code ECS049)
Product Availability
BACKlighting lamp modules are ideally suited to fit contours
and curves typical to advertising space and channel letters,
and can be used for general signage applications too. They
are available in red, yellow, true green, white, orange and blue.
Product
Color
BACKLITE/633/OS/LM03A/S
BACKLITE/615/OS/LM03A/A
BACKLITE/610/OS/LM03A/O
BACKLITE/587/OS/LM03A/Y
BACKLITE/525/0S/LM03A/T
BACKLITE/470/OS/LM03A/B
BACKLITE/OS/LM03A/W1
SUPER RED
AMBER RED
ORANGE
YELLOW
TRUE GREEN
BLUE
WHITE
WHITE
WHITE
OPTOTRONIC® LED power supplies from OSRAM SYLVANIA
are specially designed to operate the BACKlight modules
at 10.5V. A range of UL Class 2 power supplies are available
for indoor and outdoor, dry and damp location use.
BACKLITE/OS/LM03A/W2-854
BACKLITE/OS/LM03A/W2-865
Application Information
Application Notes
Applications
1. Small dimensions
2. Shock resistance
3. High color efficiency
Backlighting advertising panels
Signs, channel letters, and displays
General lighting
4. Directional radiation characteristics
5. No IR/UV radiation
6. Power supplies for operation
LED005R4
Maximum Ratings
Parameter
Symbol
Values
Units
Operating Temperature*
Storage Temperature Range
Maximum Voltage
T op
T stg
V max
V R
-30… +75
-40… +85
11
°C
°C
V dc
V dc
Reverse Voltage
11
* Temperature should be measured at the T point on the module. (Operating temperature for red, amber, orange and yellow modules is -40°C to +85°C)
c
Dimensions
Length
mm (in)
Width
mm (in)
Smallest Unit
LED Grid
Cable
30 (1.18)
15 (0.59)
50 (1.97)
30 (1.18)
Dimensions on diagrams in mm, unless stated otherwise.
Opto Semiconductors
OSRA
Tc Point
8 Boards electrically connected
Opto Semiconductors
Opto Semiconductors
Opto Semiconductors
Opto Semiconductors
Opto Semiconductors
Opto Semiconductors
Opto Semiconductors
Opto Semiconductors
OSRAM
OSRAM
OSRAM
OSRAM
OSRAM
OSRAM
OSRAM
OSRAM
0.8 ft. to 1.8 ft.
Safety Information
1. The LED module and its components should not be mechanically stressed.
2. Assembly must not damage or destroy conducting paths on the circuit board.
3. To avoid mechanical damage to the connecting cables, the boards should be attached securely to the intended substrate.
Heavy vibration should be avoided.
4. Detach each circuit board unit of the module only be severing the connecting cables (with power disconnected).
The LED Module incorporates no protection against short circuits, overload or overheating. Therefore it is necessary to operate
the modules with an electronically stabilized power supply offering protection against the above mentioned safety risks.
OSRAM OPTOTRONIC power supplies are specifically designed with protection features for safe operation.
When using power supplies other than OPTOTRONIC the following basic safety features should be verified in addition to any
other application specific concerns and local safety codes:
• Short circuit protection
• Overload protection
• Overheat protection
• Correct output voltage, including consideration for ripple and spikes.
5. Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards.
Only qualified personnel should be allowed to perform installations.
6. Correct electrical polarity needs to be observed. Wrong polarity may destroy the module!
7. Parallel connection is highly recommended for safe electrical operation mode. Serial connection of more than 3 modules
is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module.
8. Electrical contact is achieved with the contact cables. A maximum of 3 modules can be installed consecutively from one power feed.
Operation with more than 3 consecutive BACKlight modules will reduce photometric performance and exceed the current carrying
capacity of the module. If more than 3 modules are connected in series (maximum 6), power feed should be to the center of the string.
9. The module itself is protected against condensation water with a polymeric conformal coating. Supplementary soldering on any solder
pad will destroy the conformal coating and with it protection against condensation water.
10. Operation in or under water is not allowed.
Assembly Information
1. Mounting of the LED module may be performed with screws or Snap-In spacer (e.g. from Richco www.richco-int.com)
by using 4 mm holes in the circuit board. See the “BACKlight Intallation Guide” for more details.
2. The mounting of the module is carried out by attaching it at the mounting holes. Mounting screws should be used with
synthetic washers to prevent circuit board damage and possible short circuiting.
3. A maximum of 3 modules can be installed consecutively from any power feed. Installation with more than 3 BACKlight Modules
may take the form of, for example, either 6 modules installed consecutively with a power feed to the center or with a splitting
of the power feed to contact groups of 3 modules.
4. To connect the LED modules with each other or with OPTOTRONIC Power Supply we recommend standard connectors
(e.g. WAGO 243-214 or 224-201).
5. Derate maximum LED load for remote mounting or exterior applications. Contact OSRAM SYLVANIA for details.
Ordering and Specification Information*
Wave Length
(nm) or
Color temp. (K)
Item
Ordering
Volts
Watts (V DC)
Current Viewing
Number
of LEDs
Luminous
Flux (lm)
Number Abbreviation
Color
(Amps)
Angle
70081
70011
70071
70012
70013
70014
70045
BACKLITE/633/OS/LM03A/S
Super Red
Amber Red
Orange
Yellow
True Green
Blue
White
White
White
4.2
4.2
4.2
4.2
4.2
4.2
3.4
5.3
5.3
10.5
10.5
10.5
10.5
10.5
10.5
10.5
10.5
10.5
0.40
0.40
0.40
0.40
0.40
0.40
0.32
0.50
0.50
120
120
120
120
120
120
120
120
120
32
32
32
32
32
32
32
32
32
633 nm
617 nm
606 nm
587 nm
525 nm
54
54
86
69
57
9
29
69
69
BACKLITE/615/OS/LM03A/A
BACKLITE/610/OS/LM03A/O
BACKLITE/587/OS/LM03A/Y
BACKLITE/525/OS/LM03A/T
BACKLITE/470/OS/LM03A/B
BACKLITE/OS/LM03A/W1
470 nm
x = 0.32; y =0.31
5400K
70102** BACKLITE/OS/LM03A/W2-854
70103** BACKLITE/OS/LM03A/W2-865
6500K
*
All Information relates to entire module with 32 LEDs. Modules may be sub-divided into 8 coupons of 4 LEDs each.
Data reflects statistical mean values. Actual data may differ depending on variances in the manufacturing process.
** New product. Contact OSRAM SYLVANIA for availability.
Power Supply Ordering Information
®
OPTOTRONIC 6W (51500)
OPTOTRONIC 25W (51505)
OPTOTRONIC 50W (51508, 51509)
LED Item
Number
No. of
Modules*
Max.
Length (ft)
No. of
Modules*
Max.
Length (ft)
No. of
Modules*
Max.
Length (ft)
Color
70081
70011
70071
70012
70013
70014
70045
70102
70103
Super Red
Amber red
Orange
Yellow
True Green
Blue
White
White (W2)
White (W2)
1
1
1
1
1
1
1
1
1
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
6
6
6
6
6
6
7
4
4
10.8
10.8
10.8
10.8
10.8
10.8
12.6
7.2
12
12
12
12
12
12
14
9
21.6
21.6
21.6
21.6
21.6
21.6
25.2
16.2
16.2
7.2
9
* Each module can be sub-divided into 8 coupons.
Ordering Guide
OSRAM SYLVANIA
National Customer
BACKLITE
/
470
/
OS
/
LM03A
ID No.
/
B
Service and Sales Center
18725 N. Union Street
Westfield, IN 46074
Backlight Module
Wavelength
470 nm
Opto
Semiconductor
Color Code
B = Blue
Industrial & Commercial
Phone:1-800-255-5042
Fax: 1-800-255-5043
National Accounts
Phone:1-800-562-4671
Fax: 1-800-562-4674
OEM/Specialty Markets
Phone:1-800-762-7191
Fax: 1-800-762-7192
Photo-Optic
Phone:1-888-677-2627
Fax: 1-800-762-7192
In Canada
OSRAM SYLVANIA LTD.
Headquarters
2001 Drew Road
Mississauga, ON L5S 1S4
Industrial & Commercial
Phone:1-800-263-2852
Fax: 1-800-667-6772
Special Markets
Phone:1-800-265-2852
Fax: 1-800-667-6772
TOPLED is a registered trademark of Siemens Aktiengesellschaft Corporation.
OPTOTRONIC is a registered trademark of OSRAM GmbH used under license.
OSRAM is a registered trademark of OSRAM GmbH.
Specifications subject to change without notice.
Visit our website: www.sylvania.com
相关型号：
©2020 ICPDF网 联系我们和版权申明