ARJ2003Y [PANASONIC]
Electromechanical Relay, DPDT, 3.3VDC (Coil), 0.3A (Contact), 30VDC (Contact), Random, DC Output;型号: | ARJ2003Y |
厂家: | PANASONIC |
描述: | Electromechanical Relay, DPDT, 3.3VDC (Coil), 0.3A (Contact), 30VDC (Contact), Random, DC Output 光电二极管 继电器 |
文件: | 总5页 (文件大小:1037K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Up to 8 GHz
small microwave relays
RJ RELAYS (ARJ)
9.00
.354
FEATURES
• Excellent high frequency
characteristics (50, at 5GHz)
V.S.W.R.: Max. 1.25
TYPICAL APPLICATIONS
Measuring equipment market
Attenuator circuits, spectrum analyzer,
oscilloscope
14.0
.551
8.20
.323
Insertion loss: Max. 0.5dB
Isolation: Min. 35dB
Mobile telecommunication market
IMT2000, microwave communication
9.00
.354
14.0
.551
(Between open contacts)
Min. 30dB
Medical instrument market
8.20
.323
(Between contact sets)
• Surface mount terminal
Surface mount terminals are now
standard so there is much less work in
designing PC boards.
• Small size
Size: 14.00 (L)9.00 (W)8.20 (H) mm
.551 (L).354 (W).323 (H) inch
SPECIFICATIONS
Contact
Characteristics
Arrangement
2 Form C
Min. 500 M
Initial insulation resistance*1
Between open contacts
Between contact sets
(at 500 V DC)
500 Vrms
500 Vrms
500 Vrms
500 Vrms
Contact material
Gold plating
Initial contact resistance
(By voltage drop 10V DC 10mA)
Max. 150m
Initial
1W (at 5 GHz, Impedance
50 , V.S.W.R. &1.25)
10mA 10V DC (resistive load)
breakdown Between contact and coil
Contact rating
voltage*2
for 1 min.
Between coil and earth terminal
Between contact and earth
500 Vrms
1W (at 5 GHz, Impedance 50
Rating
terminal
Contact carrying power
, V.S.W.R. &1.25)
Operate time [Set time]*3 (at 20C)
Release time (without diode)[Reset time]*3
(at 20C)
Temperature rise (at 20C)*4
Max. 5ms [Max. 5 ms]
Max. 5ms [Max. 5 ms]
Max. switching voltage
Max. switching current
V.S.W.R.
30 V DC
0.3 A DC
Max. 1.25
Max. 50C
Min. 500 m/s2
Min. 1,000 m/s2
Insertion loss
(without D.U.T. board’s loss)
Functional*5
Destructive*6
Max. 0.5dB
Min. 35dB
Min. 30dB
High frequency
characteristics
(Initial)
(~5GHz,
Impedance
50)
Shock resistance
Between
10 to 55 Hz at double
amplitude of 3 mm
Functional*7
Vibration resistance
open contacts
Isolation
Between
10 to 55 Hz at double
amplitude of 5 mm
contact sets
Destructive
1W (at 5GHz, impedance 50,
V.S.W.R. &1.25, at 20C)
Input power
Conditions for operation,
Ambient temp.
–30C to 70C
–22F to 158F
transport and storage*8
Mechanical (at 180 cpm)
1W, at 5GHz,
107
(Not freezing and condensing
at low temperature)
Humidity
5 to 85% R.H.
Expected life
(min.
operations)
106
Electrical
V.S.W.R. & 1.25
Unit weight
Approx. 3 g .11 oz
(at
10mA 10V DC
20cpm)
106
Remarks
(resistive load)
* Specifications will vary with foreign standards certification ratings.
*1 Measurement at same location as “Initial breakdown voltage” section.
*2 Detection current: 10mA
*3 Nominal operating voltage applied to the coil, excluding contact bounce time.
*4 By resistive method, nominal voltage applied to the coil, 5GHz, V.S.W.R. & 1.25
*5 Half-wave pulse of sine wave: 6ms, detection time: 10s.
*6 Pulse of sine wave: 11ms.
Coil (at 20C, 68F)
Nominal operating power
Single side stable
2 coil latching
200 mW
150 mW
*7 Detection time: 10s
*8 Refer to 6. Conditions for operation, transport and storage conditions in NOTES
(Page 4).
ds_61313_en_rj: 010611J
1
RJ (ARJ)
ORDERING INFORMATION
Ex. ARJ
2
Contact arrangement Operating function
Terminal shape
Packing style
Nil: Carton packing
X: Tape end reel packing
(picked from 1/2/3-pin side)
Z: Tape and reel packing (picked
from 6/7/8-pin side)
Coil voltage (DC)
2: 2 Form C
0: Single side stable Nil: Standard PC board terminal
2: 2 coil latching A: Surface-mount terminal
03 : 3V
4H: 4.5V
12 : 12V
24 : 24V
Note: Tape and reel packing symbol "-Z" is not marked on the relay. "X" type tape and reel packing (picked from 1/2/3-pin side) is
also available. Suffix "X" instead of "Z".
TYPES AND COIL DATA (at 20C 68F)
1. Standard PC board terminal
• Packing of standard PC board terminal: 50 pcs. in an inner package (carton); 500 pcs. in an outer package
Part No.
Max.
allowable
voltage, V DC
(at 70°C
Pick-upvoltage, Drop-out voltage, Nominaloperating
Nominal
operating
power, mW
Operating Coil Rating,
Coil resistance,
V DC (max.)
(initial)
V DC (min.)
(initial)
current, mA
(10%)
Standard PC
board terminal
function
V DC
(10%)
158°F)
3
4.5
12
24
ARJ2003
ARJ204H
ARJ2012
ARJ2024
2.25
3.375
9
0.3
0.45
1.2
2.4
66.6
44.4
16.6
8.3
45
101.2
720
200
200
200
200
3.3
4.95
13.2
26.4
Singleside
stable
18
2,880
Part No.
Max.
allowable
voltage, V DC
(at 70°C
Set voltage,
V DC (max.)
(initial)
Reset voltage, Nominaloperating
Nominal
operating
power, mW
Operating Coil Rating,
Coil resistance,
V DC (min.)
(initial)
current, mA
(10%)
Standard PC
board terminal
function
V DC
(10%)
158°F)
3
4.5
12
24
ARJ2203
ARJ224H
ARJ2212
ARJ2224
2.25
3.375
9
2.25
3.375
9
50
60
135
150
150
150
150
3.3
4.95
13.2
26.4
33.3
12.5
6.3
2 coil
latching
960
18
18
3,840
2. Surface-mount terminal
• Packing of surface-mount terminal: 50 pcs. in an inner package (carton); 500 pcs. in an outer package
• Packing of surface-mount terminal: 500 pcs. in an inner package (tape and reel); 500 pcs. in an outer package
Part No.
Max.
Pick-up
voltage, V DC voltage, V DC
(max.) (initial) (min.) (initial)
Drop-out
Nominaloperating
current, mA
(10%)
Coil
Nominal
allowable
Operating Coil Rating,
resistance, operating voltage, V DC
(10%) power, mW
Carton
packing
Tape and
reel packing
function
V DC
(at 70°C
158°F)
3
4.5
12
24
ARJ20A03 ARJ20A03Z
ARJ20A4H ARJ20A4HZ
ARJ20A12 ARJ20A12Z
ARJ20A24 ARJ20A24Z
2.25
3.375
9
0.3
0.45
1.2
2.4
66.6
44.4
16.6
8.3
45
200
200
200
200
3.3
4.95
13.2
26.4
101.2
720
Singleside
stable
18
2,880
Part No.
Max.
Set voltage,
V DC (max.) voltage, V DC
Reset
Nominaloperating
current, mA
(10%)
Coil
Nominal
allowable
Operating Coil Rating,
resistance, operating voltage, V DC
(10%) power, mW
Carton
packing
Tape and
reel packing
function
V DC
(initial)
(min.) (initial)
(at 70°C
158°F)
3
4.5
12
24
ARJ22A03 ARJ22A03Z
ARJ22A4H ARJ22A4HZ
ARJ22A12 ARJ22A12Z
ARJ22A24 ARJ22A24Z
2.25
3.375
9
2.25
3.375
9
50
60
135
150
150
150
150
3.3
4.95
13.2
26.4
33.3
12.5
6.3
2 coil
latching
960
18
18
3,840
ds_61313_en_rj: 010611J
2
RJ (ARJ)
REFERENCE DATA
1. High frequency characteristics
Sample: ARJ20A12
Measuring method: Measured with MEW PC board by HP network analyzer (HP8510C).
• V.S.W.R. characteristics
• Insertion loss characteristics
• Isolation characteristics
(without D.U.T. board’s loss)
0
0
10
20
2.0
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
0.5
1.0
Between contact sets
30
40
50
60
70
80
1.5
2.0
2.5
3.0
Between open contact
1.0
45MHz
5GHz
8GHz
45MHz
5GHz
8GHz
45MHz
5GHz
8GHz
Frequency
Frequency
Frequency
DIMENSIONSmm inch
Download CADData from our Web site.
1. Standard PC board terminal
Expansion of A
Schematic (Bottom view)
CAD Data
10.6
Single side stable
2 coil latching
.417
Direction
indication
Com
-
+
1
2
3
Com
2
10.4
.409
+
-
1
3
0 to 0.2
0 to .008
10
NC
9
4
5
NO
10
NC
4
5
NO
(Typical: 0.1)
(Typical: .004)
9
2 4 ribs should be soldered
with PC board ground.
12.2
.480
8
7
6
+
-
Com
8
7
Com
6
9.00
.354
14.0
.551
(Reset condition)
(Deenergized condition)
3 Better HF characteristics
may be obtained when thi
portion is soldered with
PC board ground.
A
3.50
.138
8.20
.323
0.50
.020
0.40
.016
0.50
.020
8.89
.350
3.81
.150
12.70
7.62
.300
.500
11.40
.449
0.20
.008
0.50
.020
6.36
.250
1All bottom surface of the base should be
touched closely or soldered with PC board
ground.
0.20
.008
0.15
.006
General tolerance: 0.3 .012
2. Surface mount terminal
Expansion of A:
Coplanarity of terminals
& ribs & base
Schematic (Top view)
CAD Data
10.6
.417
Single side stable
2 coil latching
0.50
.020
Direction
indication
Com
Com
-
+
8
7
6
8
7
6
9
NC
10
5
4
3.81
.150
10.4
.409
NO
9
NC
10
5
4
0.50
.020
NO
0 to 0.2
0 to .008
0.40
.016
1
2
Com
3
+
-
8.89
.350
12.2
.480
1
2
Com
3
2 4 ribs should be soldered
-
+
(Typical: 0.1)
(Typical: .004)
with PC board ground.
(Reset condition)
(Deenergized condition)
9.00
.354
14.0
.551
A
3 Better HF characteristics
0.20
.008
may be obtained when thi
8.20
.323
portion is soldered with
PC board ground.
15.0
.591
10.0
.394
11.40
.449
0.50
.020
6.36
.250
1 All bottom surface of the base should be
touched closely or soldered with PC board
ground.
General tolerance: 0.3 .012
ds_61313_en_rj: 010611J
3
RJ (ARJ)
NOTES
1. Coil operating power
6. Conditions for operation, transport
and storage conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
occur. Be sure to mount the relay under
the required mounting conditions.
7. Soldering
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different. The nominal operating voltage
should be applied to the coil for more
than 20 ms to set/reset the latching type
relay.
1) Surface-mount terminal
In case of automatic soldering, the
following conditions should be observed
(1) Position of measuring temperature
–30 to +70C –22 to +158F
(However, tolerance range is –30 to
+60C –22 to +140F if package is
carried as is.)
Surface of PC board where relay is mounted.
(2) Humidity: 5 to 85% RH
2. Coil connection
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
(2) IR (infrared reflow) soldering method
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
T3
T2
T1
3. External magnetic field
Since RJ relays are highly sensitive
polarized relays, their characteristics will
be affected by a strong external magnetic
field. Avoid using the relay under that
condition.
t1
t2
Humidity, %R.H.
T1 = 150 to 180C 302 to 356F
T2 = 230C 446F and higher
T3 = Within 250C 482F
t1 = 60 to 120 sec.
t2 = Within 30 sec.
85
4. Cleaning
Tolerance range
Temperature rise of relay itself may vary
according to the mounting level or the
heating method of reflow equipment.
Therefore, please set the temperature of
soldering portion of relay terminal and the
top surface of the relay case not to
exceed the above mentioned soldering
condition.
It is recommended to check the
temperature rise of each portion under
actual mounting condition before use.
2) Standard PC board terminal
Please meet the following conditions if
this relay is to be automatically soldered.
(1) Preheating: Max. 120C 248F
(terminal solder surface) for max. 120
seconds
(2) Soldering: Max. 260±5C 500±9F for
max. 6 seconds
The effect on the relay depends on the
actual substrate used. Please verify the
substrate to be used.
Moisture-proof packaging enables RJ
relay’s standard PCB type capable for
reflow soldering.
Please contact us in the case of reflow
soldering considerations.
For automatic cleaning, the boiling
method is recommended. Avoid
ultrasonic cleaning which subjects the
relays to high frequency vibrations, which
may cause the contacts to stick.
It is recommended that alcoholic solvents
be used.
(Avoid freezing (Avoid
when used at
temperatures
lower than
condensation
when used at
temperatures
higher than
0C 32F)
0C 32F)
5
-30
-22
0
70
158
32
Temperature, C F
2) Condensation
5. Tape and reel packing
1) Tape dimensions
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0C 32F. This causes
problems such as sticking of movable
parts or operational time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
4.00 .157
2.0
(Accumulation 10 pitch:
40±0.1 1.575±.004)
8.80
.346
8.50
.337
.079
16.00
.630
0.40±0.05
1.75
.016±.002
.069
7.40
.291
1.50
.059
11.50
.453
16.00
24.00 .630
.945
11.20
.441
14.40
.570
6.20
.244
(10.75)
(.423)
11.40
.449
9.40
.370
1.33
.052
2.57
.101
2) Dimensions of plastic reel
5) Storage procedures for surface-mount
terminal types
21±0.8 dia.
.827±.031 dia.
3) Hand soldering
Since the relay is very sensitive to
humidity, it is packed in humidity-free,
hermetically sealed packaging. When
storing the relay, be careful of the
following points:
(1) Be sure to use the relay immediately
after removing it from its sealed package.
(2) When storing the relay for long
periods of time after removing it from its
sealed package, we recommend using a
humidity-free bag with silica gel to
prevent subjecting the relay to humidity.
Furthermore, if the relay is solder
mounted when it has been subjected to
excessive humidity, cracks and leaks can
Please meet the following conditions if
this relay is to be soldered by hand.
(1) Wattage: 30 to 60 W
(2) Tip temperature/time: 280 to 300C
536 to 572F for max. 5 seconds
The effect on the relay depends on the
actual substrate used. Please verify the
substrate to be used.
4) Avoid high frequency cleaning since
this may adversely affect relay
characteristics. Use alcohol-based
cleaning solutions when cleaning relays.
2.0±0.5
.079±.020
100±1 dia.
3.937±.039 dia.
370±2 dia.
14.567±.079 dia.
13±0.2 dia.
.512±.008 dia.
2.0±0.2
.079±.008
24.4 +02
.961 0+.079
ds_61313_en_rj: 010611J
4
RJ (ARJ)
8. Measuring method (Impedance 50)
<Standard PC board terminal>
to contact shifting.
1
2
• High-frequency load-operating
When high-frequency opening and
closing of the relay is performed with a
load that causes arcs at the contacts,
nitrogen and oxygen in the air is fused by
the arc energy and HNO3 is formed. This
can corrode metal materials.
8.35
.329
PORT2
B
A
R
B
A
R
Network
analyzer
S parameter
test set
1.00
.039
1
2
HP 8510C
HP 8515A
7.62
.300
RF
RF
IN
OUT
3.81
.150
PORT1
Three countermeasures for these are
listed here.
(1) Incorporate an arc-extinguishing
circuit.
Connector
12.70
.500
No.
Product name
Contents
17.00
.669
0.40
.016
0.40
.016
3.5 mm testport,
Extension cable
6-1.86
6-.073
1
HP 85131-60013
0.90
.035
(2) Lower the operating frequency
(3) Lower the ambient humidity
2) Use the relay within specifications
such as coil rating, contact rating and on/
off service life. If used beyond limits, the
relay may overheat, generate smoke or
catch fire.
3) Be careful not to drop the relay. If
accidentally dropped, carefully check its
appearance and characteristics before
use.
3.5 mm coaxial
adaptor
2
HP 83059
(Step 1) Calibrate the test system with
HP calibration kit [HP85052B]
(Step 2) After calibration, connect the
D.U.T. board and measure.
20.00
.787
6.72
.265
6.62
.261
0.50
.020
Connect 50 terminals on
connectors other than those for
measurement.
0.50
.020
8.89
.350
11.70
.461
Notes)
30.00
1.181
1. All bottom surface of the base should be
touched closely or soldered with PC board
ground.
2. 4 ribs should be soldered with PC board
ground.
<Calibration board>
4) Be careful to wire the relay correctly.
Otherwise, malfunction, overheat, fire or
other trouble may occur.
14.5
.571
10.0
.394
5) If a relay stays on in a circuit for many
months or years at a time without being
activated, circuit design should be
reviewed so that the relay can remain
non-excited. A coil that receives current
all the time heats, which degrades
insulation earlier than expected. A
latching type relay is recommended for
such circuits.
Measuring board
1) Dimensions
<Surface mount terminal>
0.40 or 0.50
.016 or .020
1.76 or 1.86
.069 or .073
17.00
.669
2) Material: Glass PTFE double-sided
through hole PC board R-4737
(Matsushita Electric Works)
3) Board thickness: t = 0.8 mm
4) Copper plating: 18m
6-1.76
6-.069
0.40
.016
0.40
.016
0.80
.031
6) The latching type relay is shipped in
the reset position. But jolts during
transport or impacts during installation
can change the reset position. It is,
therefore, advisable to build a circuit in
which the relay can be initialized (set and
reset) just after turning on the power.
7) If silicone materials (e.g., silicone
rubbers, silicone oils, silicone coating
agents, silicone sealers) are used in the
vicinity of the relay, the gas emitted from
the silicone may adhere to the contacts of
the relay during opening and closing and
lead to improper contact. If this is the
case, use a material other than silicone.
8) We recommend latching type when
using in applications which involve
lengthy duty cycles.
• Connector (SMA type receptacle)
Product name: R125 510 (RADIALL)
Insertion loss compensation
The insertion loss of relay itself is given
by subtracting the insertion loss of short-
circuit the Com and the NC (or NO).
(signal path and two connectors)
9. Others
1) The switching lifetime is defined under
the standard test condition specified in
the JIS* C 5442-1996 standard
(temperature 15 to 35C 59 to 95F,
humidity 25 to 75%). Check this with the
real device as it is affected by coil driving
circuit, load type, activation frequency,
activation phase, ambient conditions and
other factors.
7.07
.278
7.22
.284
2.81
.111
0.40
.016
0.40
.016
8.89
.350
12.04
.474
8.35
.329
1.00
.039
20.00
.787
30.00
1.181
Also, be especially careful of loads such
as those listed below.
* Japanese Industrial Standards
• When used for AC load-operating and
the operating phase is synchronous.
Rocking and fusing can easily occur due
For Cautions for Use, see Relay Technical Information.
ds_61313_en_rj: 010611J
5
相关型号:
ARJ2012X
Electromechanical Relay, DPDT, 13.2VDC (Coil), 0.3A (Contact), 30VDC (Contact), Random, DC Output
PANASONIC
ARJ2012Y
Electromechanical Relay, DPDT, 13.2VDC (Coil), 0.3A (Contact), 30VDC (Contact), Random, DC Output
PANASONIC
ARJ2024X
Electromechanical Relay, DPDT, 26.4VDC (Coil), 0.3A (Contact), 30VDC (Contact), Random, DC Output
PANASONIC
ARJ2024Y
Electromechanical Relay, DPDT, 26.4VDC (Coil), 0.3A (Contact), 30VDC (Contact), Random, DC Output
PANASONIC
©2020 ICPDF网 联系我们和版权申明