ERA-6YEB513V [PANASONIC]
Metal Film Chip Resistors 0603, 0805; 金属片式电阻器0603 , 0805型号: | ERA-6YEB513V |
厂家: | PANASONIC |
描述: | Metal Film Chip Resistors 0603, 0805 |
文件: | 总3页 (文件大小:186K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Metal Film Chip Resistors
Metal Film Chip Resistors
0603, 0805
Type:
ERA 3Y, 6Y
■ Features
● Small size and lightweight
● High reliability
Low T.C.R. & current noise, excellent non-linearity
● Suitable for both reflow and flow soldering
● Reference Standards
IEC 60115-8, JIS C 5201-8, EIAJ RC-2133A
● RoHS compliant
■ Explanation of Part Numbers
1
2
3
4
5
6
7
8
9
10
11
E
R
A
3
Y
E
B
1
0
2
V
Product Code
Size, Power Rating
Resistance Tolerance
Packaging Methods
Temperature Coefficient
Type: inches Power Rating
Code
B
D
Tolerance
0.1 %
0.5 %
Packaging
Punched Carrier Taping
4 mm pitch
Type
ERA3Y
ERA6Y
Metal Film
Chip Resistors
Code
T.C.R.
Code
25ꢀ10–6/°C (ppm/°C)
50ꢀ10–6/°C (ppm/°C)
100ꢀ10–6/°C (ppm/°C)
0.1 W
3Y : 0603
E
H
K
V
0.125 W
6Y : 0805
Resistance Value
The first two digits are significant figures of resistance
and the third one denotes number of zeros following.
■ Construction
■ Dimensions in mm (not to scale)
L
Protective coating
a
Electrode (Inner)
Alumina substrate
W
t
b
Electrode
(Between)
Dimensions (mm)
a
Type
(inches)
Mass (Weight)
[g/1000pcs.]
L
W
b
t
High reliability
metal film
Electrode (Outer)
0.20
0.20
0.20
0.20
0.20
0.25
0.10
0.10
ERA3Y
(0603)
1.60
0.80
1.25
0.30
0.40
0.30
0.45
2
4
0.10
0.25
ERA6Y
(0805)
2.00
0.40
0.50
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Aug. 2008
Metal Film Chip Resistors
■ Ratings
Category Temperature
Range (Operating
Temperature Range)
(°C)
Limiting Element Maximum Overload Resistance
Resistance
Range(3)
(ꢁ)
T.C.R.
Type
(inches)
Power Rating
at 70 °C (W)
Voltage (Maximum
Voltage(2)
(V)
Tolerance
(%)
[ꢀ10–6/°C
(ppm/°C)]
RCWV)(1) (V)
10 to
91 (E24)
50
25
100
25
0.5
0.1
0.5
0.1
100 to 33 k (E24)
36 k to 330 k (E24)
100 to 33 k (E24)
ERA3Y
(0603)
0.1
75
150
200
–55 to +125
10 to
91 (E24)
50
25
100
25
100 to 100 k (E24)
110 k to 1 M (E24)
100 to 100 k (E24)
ERA6Y
(0805)
0.125
100
ꢂ
(1) Rated Continuous Working Voltage (RCWV) shall be determined from RCWV= Rated Power ꢀ Resistance Values, or Limiting Element Voltage
(max. RCWV) listed above, whichever less.
(2) Overload (Short-time Overload) Test Voltage (SOTV) shall be determined from SOTV=2.5 ꢀ Power Rating or max. Overload Voltage listed above
whichever less.
(3) E96 series resistance values are also available. Please contact us for details. Part Number of E96 series is shown ERA3E. , ERA6E.
–55 °C
100
70 °C
Power Derating Curve
80
60
40
20
0
For resistors operated in ambient temperatures above
70 °C, power rating shall be derated in accordance
with the figure on the right.
125 °C
–60 –40 –20
0
20 40 60 80 100 120 140 160 180
Ambient Temperature (°C)
■ Packaging Methods (Taping)
● Standard Quantity
Type
ERA3Y
ERA6Y
Kind of Taping
Pitch (P1)
4 mm
Quantity
Punched Carrier Taping
5000 pcs./reel
● Punched Carrier Taping
● Taping Reel
T
Sprocket hole
Compartment
φC
φD0
A
Chip component
Tape running direction
T
P1 P2 P0
φA
W
Type
3Y 1.10
6Y 1.65
A
B
1.90
2.50
W
F
E
Type
3Y
6Y
A
B
C
φ
φ
φ
Dimensions
(mm)
Dimensions
0.10
0.15
0.10
0.20
+0
0.20
0.10
0.05
0.10
1.0
8.00
3.50
1.75
180.0
60 min.
13.0
–3.0
(mm)
Type
3Y
6Y
P1
P2
P0
4.00
D
T
0.70
0.84
Type
3Y
6Y
W
T
φ
0
Dimensions
(mm)
Dimensions
0.05
0.05
0.10
0.05
+0.10
–0
1.0
1.0
4.00
2.00
1.50
9.0
11.4
(mm)
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Aug. 2008
Metal Film Chip Resistors
■ Recommended Land Pattern
In case of flow soldering, the land width must be smaller than the Chip Resistor width to properly control the solder amount
properly. Generally, the land width should be 0.7 to 0.8 times (W) of the width of chip resistor. In case of reflow soldering,
solder amount can be adjusted, therefore the land width should be set to 1.0 to 1.3 times chip resistor width (W).
Dimensions (mm)
b
Type
(inches)
Chip Resistor
a
c
ERA3Y
(0603)
0.7 to 0.9
2 to 2.2
0.8 to 1
a
b
ERA6Y
(0805)
1 to 1.4
3.2 to 3.8
0.9 to 1.4
■ Recommended Soldering Conditions
Recommendations and precautions are described below.
Recommended soldering conditions for reflow
●
· Reflow soldering shall be performed a maximum of
two times.
· Please contact us for additional information when
used in conditions other than those specified.
· Please measure the temperature of the terminals
and study every kind of solder and printed circuit
board for solderability before actual use.
For soldering (Example : Sn/Pb)
Temperature
Time
Preheating
Main heating
Peak
140 °C to 160 °C
Above 200 °C
235 5 °C
60 s to 120 s
30 s to 40 s
max. 10 s
Peak
Preheating
For lead-free soldering (Example : Sn/Ag/Cu)
Temperature
150 °C to 180 °C
Above 230 °C
max. 260 °C
Time
Heating
Preheating
Main heating
Peak
60 s to 120 s
30 s to 40 s
max. 10 s
Time
Recommended soldering conditions for flow
●
For soldering
For lead-free soldering
Temperature
140 °C to 180 °C
245 5 °C
Time
60 s to 120 s
20 s to 30 s
Temperature
150 °C to 180 °C
max. 260 °C
Time
60 s to 120 s
max. 10 s
Preheating
Soldering
Safety Precautions
The following are precautions for individual products. Please also refer to the precautions common to Fixed Resistors
shown on page ER2 of this catalog.
1. Keep the rated power and ambient temperature within the specified derating curve.
* When positioning and mounting Metal Film Chip Resistors (hereafter called the resistors), make allowance for the
effect of heat generated through close contact between the resistors and neighboring components and for the
temperature rise of adjacent heat-generating components.
2. If a transient load (heavy load in a short time) like a pulse is expected to be applied, check and evaluate the operations
of the resistors when installed in your products before use.
When applying pulses to the resistors, keep the pulse peak within the rated voltage.
3. Do not use halogen-based or other high-activity flux. Otherwise, the residue may impair the resistors' performance
and/or reliability.
4. When soldering with a soldering iron, never touch the resistors' bodies with the tip of the soldering iron. When using a
soldering iron with a high temperature tip, finish soldering as quickly as possible (within three seconds at 350 °C max.).
5. As the amount of applied solder becomes larger, the mechanical stress applied to the resistors increases, causing
problems such as cracks and faulty characteristics. Avoid applying an excessive amount of solder.
6. When the resistors' protective coatings are chipped, flawed, or removed, the characteristics of the resistors may be
impaired. Take special care not to apply mechanical shock during automatic mounting or cause damage during
handling of the boards with the resistors mounted.
7. Do not apply shock to the resistors or pinch them with a hard tool (e.g. pliers and tweezers). Otherwise, the resistors'
protective coatings and bodies may be chipped, affecting their performance.
8. Avoid excessive bending of printed circuit boards in order to protect the resistors from abnormal stress.
9. Do not immerse the resistors in solvent for a long time. Before using solvent, carefully check the effects of immersion.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Feb. 2006
相关型号:
©2020 ICPDF网 联系我们和版权申明