ERJ-XGNJ224Y [PANASONIC]
PRODUCT SPECIFICATION FOR APPROVAL; 要求批准产品规格
| 型号： | ERJ-XGNJ224Y |
| 厂家： | 
PANASONIC |
| 描述： | PRODUCT SPECIFICATION FOR APPROVAL |
| 文件： | 总12页 (文件大小：324K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION 151-SRJ-EX07A
ERJXGN
11 - 1
1. Dimension
a
L
a
(1) Substrate : Alumina
W
(2) Protective Coating : Resin
(Restricted Flame Retardant Free)
(3) Resistive Element : Metal glaze
(4) Inner Termination : Thick film material
(5) Middle Termination : Ni Plating
(6) Outer Termination : Sn Plating
(1)
(2)
(3)
(4)
(5)
(6)
t
b
b
L
W
a
b
t
Dimension (mm)
0.40+/-0.02 0.20+/-0.02 0.10+/-0.03 0.10+/-0.03 0.13+/-0.02
2. Power Derating Curve
120
100
80
60
40
20
0
70
Category temperature range:
: -55 to 125 deg.C
125
20
60
80
-20
40
120
140
100
-60 -40
0
160
Ambient Temperature (deg.C)
Figure 1
3. Ratings
Item
Rated value
Explanation
When used at ambient temperature above 70
deg.C, power rating shall be determined in
accordance with Figure 1.
Power Rating
0.031W
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION 151-SRJ-EX07A
ERJXGN
11 - 2
Item
Rated value
Explanation
The rated voltage of each resistance should be calculated from the equation
below. And when the rated voltage exceeds the maximum RCWV,
Rated voltage &
Rated Continuous the maximum RCWV should be the rated voltage.
1/2
Working Voltage
Rated voltage = (Power rating x Resistance Value)
The maximum RCWV : 15V
The overload voltage should be 2.5 times the rated voltage. And when
the voltage exceeds the maximum overload voltage, the value shown below
Max.
Overload Voltage should be the maximum overload voltage.
The maximum overload voltage : 30V
Resistance
J : +/- 5%
Tolerance
Resistance Range 10 ohm – 1.0 M ohm (E-24 series)
4. Explanation of Part Number
E
R
J
X
G
N
J
1
0
2
Y
(1)
(2)
(3)
(4)
(5)
(1) Product Code : Thick Film Chip Resistor
(2) Size and Rated Power : 0.4 mm x 0.2 mm, 0.031 W
Restricted Flame Retardant Free
(3) Resistance Tolerance
Code
J
Resistance Tolerance
+/- 5%
(4) Resistance Value
The first two digits are the significant figures of resistance value, and the last figure shows
the number of zero following in ohm.
(5) Packaging Configuration
Code
Y
Packaging Configuration
Taping (20,000pcs/reel)
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION 151-SRJ-EX07A
ERJXGN
11 - 3
5. Appearance & Construction
Item
Specification
Explanation
1. The resistive element should be covered with protective coating that don’t
fade easily. The surface of coating should avoid unevenness, flaw, pinhole
and discoloration.
2. The electrode should be printed uniformly, as shown in the dimensions.
The plating should not fade easily, and should avoid unevenness, flaw,
pinhole, projection and discoloration.
Appearance &
Construction
3. The electrode should be connected electrically, mechanically to resistive
element.
4. Dimensions of the substrate should be as in the list and it should not
have chipping, flaw, flash and crack.
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION 151-SRJ-EX07A
ERJXGN
11 - 4
As far as there shall not designation especially, the following tests and measurement shall be
operated under the following conditions.
Normal temperature : 5 deg.C to 35 deg.C
Normal humidity
: 45 % to 85 %
Normal atmospheric pressure : 86 k Pa to 106 k Pa
6. Performance Specification
Item
Specification
Test Method (JIS-C5201-1)
DC resistance value shall
be within the specified
tolerance.
DC resistance
At 20 deg.C, 65%RH
Natural resistance change per temperature
degree centigrade.
10 ohm – 91 ohm
Temperature
coefficient
of resistance
(TCR)
TCR=(R2-R1)x106/R1(t2-t1)
(x10–6/deg.C)
: +/- 300 x 10–6/deg.C
R1 : Resistance value at reference
temperature (t1)
100 ohm – 1 M ohm
: +/- 200 x 10–6/deg.C
R2 : Resistance value at test
temperature (t2)
t1 : 25 deg.C , t2 : 125 deg.C
Resistors shall be applied 2.5 times the rated
voltage for 5 seconds.
Short time
overload
∆R :
+/-(2%+0.1 ohm)
Max. overload voltage shall be 30V.
Resistors shall be subjected to 10000 cycles
of 2.5 times the rated voltage applied for 1
second with pause of 25 seconds between
tests.
Intermittent
overload
∆R :
+/-(5%+0.1 ohm)
Max. overload voltage shall be 30V.
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION 151-SRJ-EX07A
ERJXGN
11 - 5
7. Machinery characteristic
Item
Specification
Test Method (JIS-C5201-1)
Substrate : Glass epoxy (t=1.0 mm)
Span : 90mm
Bending distance : 3mm (10 seconds)
No mechanical damage.
<Test pattern>
0.2 0.2 0.2
Bending
strength
(mm)
0.2
∆R :
+/-(1%+0.05 ohm)
100
Resistors shall be dipped in the melted solder
bath at 235 deg.C +/- 5 deg.C for 2 seconds
+/- 0.5 second. Flux shall be removed from
the surface of termination with clean organic
solvent.
Termination should be
covered uniformly with solder
(Min. 95% coverage)
Solderability
Resistors shall be dipped in the melted solder
bath at 270 deg.C +/- 3 deg.C for 10 seconds
+/- 1 second.
Resistance to
soldering heat
∆R :
+/-(1%+0.05 ohm)
Resistors shall be subjected to a single
vibration having as double amplitude of 1.5
mm in 3 directions perpendicular one another
for 2 hours each. (6 hours in total)
The vibration frequency shall be varied
uniformly from 10 Hz to 55 Hz, and return
to 10 Hz traversing for 1 min.
Resistance to
vibration
∆R :
+/-(1%+0.05 ohm)
(Low frequency)
Solvent solution : Isopropyl alcohol
(1)Dipping 10 +/- 1 hours, dry in room
condition for 30 +/- 10 minutes.
Without distinct
deformation in appearance
Resistance to
solvent
(2)Ultrasonic wave washing : 5 +/- 1 min.
(0.3W/cm2,28kHz)
∆R :
+/-(0.5% +0.05 ohm)
Dry in room condition for 30 +/-10 minutes.
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION 151-SRJ-EX07A
ERJXGN
11 - 6
8. Environmental test
Item
Specification
Test Method (JIS-C5201-1)
Low
Resistors shall be exposed at -55 deg.C +/- 3
deg.C with no load for 1000 hours +48/-0
hours.
∆R :
temperature
exposure
High
+/-(1%+0.05 ohm)
Resistors shall be exposed at 125 deg.C +/- 3
deg.C with no load for 1000 hours +48/-0
hours.
∆R :
temperature
exposure
+/-(1%+0.05 ohm)
Resistors shall be tested for 5 cycles
continuously in accordance with the following
duty cycle.
Temperature
cycling
∆R :
Step Temperature (deg.C)
Time (min.)
30
1
2
3
4
-55 +/-3
Room temperature
+125 +/-3
+/-(1%+0.05 ohm)
Max. 3
30
Max.3
Room temperature
Resistors shall be exposed at 60 deg.C +/- 2
deg.C and 90% to 95% relative hummidity in
a humidity test chamber for 1000 hours +48/-0
hours.
Humidity
∆R :
(Steady state)
+/-(1%+0.05 ohm)
Resistors shall be operated at DC rated
voltage (1.5 hours "ON", 0.5 hours "OFF") for
1000 hours +48/-0 hours in a test chamber
controlled at 70 deg.C +/-2 deg.C.
∆R :
Load life
+/-(3%+0.1 ohm)
Resistors shall be operated at DC rated
voltage (1.5 hours “ON”, 0.5 hours “OFF”) for
1000 hours +48/-0 hours in a test chamber
controlled at 60 deg.C +/- 2 deg.C and at
90 % to 95% in relative hummidity.
Load life in
humidity
∆R :
+/-(3%+0.1 ohm)
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION
ERJXGN
151-SRJ-EX07A
11 - 7
9. Common precautions in handling resistors
!
Notice for use
(1) This specification shows the quality and performance of a unit component. Before adoption,
be sure to evaluate and verify the product mounting it in your product.
(2) We take no responsibility for troubles caused by the product usage that is not specified in
this specification.
(3) Use fail-safe design and ensure safety by carrying out the following items in cases where it
is forecast that the failure of the product gives serious damage to something important like
human life, for instant in traffic transportation equipment (trains, cars, traffic signal
equipment, etc.), medical equipment, aerospace equipment, electric heating appliances,
combustion and gas equipment, rotating equipment, disaster and crime preventive
equipment.
*Ensure safety as the system by setting protective circuits and protective equipment.
*Ensure safety as the system by setting such redundant circuits as do not cause danger by
a single failure.
(4) When a dogma shall be occurred about safety for this product, be sure to inform us rapidly,
operate your technical examination.
(5) The product is designed to use in general standard applications of general electric
equipment (AV products, household electric appliances, office equipment, information and
communication equipment, etc.); hence, it do not take the use under the following special
environments into consideration.
Accordingly, the use in the following special environments, and such environmental
conditions may affect the performance of the product; prior to use, verify the performance,
reliability, etc. thoroughly.
1) Use in liquids such as water, oil, chemical, and organic solvent.
2) Use under direct sunlight, in outdoor or in dusty atmospheres.
3) Use in places full of corrosive gases such as sea breeze, Cl2, H2S, NH3, SO2, and NOX.
4) Use in environment with large static electricity or strong electromagnetic waves.
5) Where the product is close to a heating component, and where an inflammable such as
a polyvinyl chloride wire is arranged close to the product.
6) Where the resistor is sealed or coated with resin, etc.
7) Where water or a water-soluble detergent is used in cleaning free soldering and in flux
cleaning after soldering (Pay particular attention to soluble flux.)
8) Use in such a place where the product is wetted due to dew condensation.
(6) If transient load (heavy load in a short time) like pulse is expected to be applied, carry out
evaluation and confirmation test with resistors actually mounted on your own board. When
the load of more than rated power is applied under the load condition at steady state, it
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION
ERJXGN
151-SRJ-EX07A
11 - 8
may impair performance and/or reliability of resistor. Never exceed the rated power. When
the product shall be used under special condition, be sure to ask us in advance.
(7) Halogen type (Chlorine type, Bromine type, etc.) or other high-activity flux is not
recommended as the residue may affect performance or reliability of resistors.
(8) When soldering with soldering iron, ground a tip of the soldering iron never touch the body
of the chip resistor with a tip of the soldering iron. When using a soldering iron with a tip
at high temperature, solder for a time as short as possible. (three seconds or less up to
350 deg.C)
(9) Avoid physical shock to the resistor and nipping of the resistor with hard tool (a pair of
pliers or tweezers) as it may damage protective film or the body of resistor and may affect
resistor’s performance.
(10) Avoid immersion of chip resistor in solvent for long time. Use solvent after the effect of
immersion is confirmed.
(11) This resistance may change with ESD.
In case of handling this product, please take care as follows.
Environment which static electricity cannot generate easily.
( Recommendation humidity: 40 - 60%)
Wearing of an earth band and a conductive glove.
Connecting surface mounting system to the earth.
Installation of the electric conduction mat on a work table.
10. Storage Method
If the product is stored in the following environments and conditions, the performance and
solderability may be badly affected, avoid the storage in the following environments.
(1) Storage in places full of corrosive gases such as sea breeze, Cl2, H2S, NH3, SO2, and NOX.
(2) Storage in places exposed to direct sunlight.
(3) Storage in places outside the temperature range of 5 deg.C to 35 deg.C and humidity
range of 45 %RH to 85 %RH.
(4) Storage over a year after our delivery (This item also applies to the case where the storage
method specified in item (1) to (3) has been followed.).
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION
ERJXGN
151-SRJ-EX07A
11 - 9
11. Laws and Regulations
(1) This product has not been manufactured with any ozone-depleting chemical controlled under
the Montreal Protocol.
(2) This product complies with the RoHS Directive (Restriction of the use of certain Hazardous
Substances in electrical and electronic equipment (DIRECTIVE 2002/95/EC)).
(3) All materials used in this part are registered material under the Law Concerning the
Examination and Regulation of Manufacturs, etc. of Chemical substances.
(4) All the materials used in this part contain no brominated materials of PBBOS or PBBS as the
flame-retardant.
(5) If you need the notice by letter of “A preliminary judgement on the Laws of Japan foreign
exchange and Foreign Trade control”, be sure to let us know.
12. Production site
Country : Japan
Plant : Panasonic Electronic Devices Fukui Co., Ltd.
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION
ERJXGN
151-SRJ-EX07A
11 - 10
13. Taped and Reel Package
13-1 Physical Dimensions
Structure and reel dimensions shall be as shown in the figure below.
Inaccordance with EIAJ ET-7200.
9.0 +/- 1.0
Carrier tape
Top tape
Adhesive tape
11.4 +/- 1.0
Unit : mm
13-2 Carrier tape dimension
Sprocket hole
E
T
P0
øD0
F
W
B
Chip resistor
F
Chip hole
A
K
P1
A
B
W
E
Dimension (mm) 0.25+/-0.03 0.45+/-0.03 8.00+/-0.20 3.50+/-0.05 1.75+/-0.10
K
P1
P0
øD0
T
Dimension (mm) 2.00+/-0.10 4.00+/-0.10 1.50+0.10/-0 0.31+/-0.03 0.16+/-0.03
13-3 Specifications
13-3-1 Taping
(1) Minimum Bending Radius
When Carrier tape shall be bent by Minimum Bending Radius (15mm), no defection of chip
and no break of carrier tape. However minimum bending radius shall be tested for 1 time.
(2) Resistance to climate of top tape
When it shall be exposed at 60 deg.C, 90 to 95 %RH for 120 hours, no exfoliation of
top tape.
Panasonic Electronic Devices Co., Ltd.
Spec. No.
Subject
Chip Resistor
Part No.
PRODUCT SPECIFICATION FOR IMFORMATION
ERJXGN
151-SRJ-EX07A
11 - 11
(3) When the test shall be operated with the below conditions, peel strength should be 0.049 N
to 0.49 N, should not have flash and tear after peeling.
(Test Method)
Carrier tape
Peeling direction
10 degree
Top tape
13-3-2 Quantity in Taping : 20,000 pcs./reel
13-3-3 Tape packaging
(1) Resistance side shall be facing upward.
(2) Chip resistor shall not be sticking to top tape.
(3) Chip resistor shall be easy to take out from carrier tape and chip hole or sprocket
hole shall not have flash and break.
13-4 Outer Packaging
Quantity : 20 reels (Max. 400,000pcs.)
Tape
Marking
* When taping shall not reach Max. or quantity, the remaining empty space shall be buried with
buffer material.
* When the quantity shall be few, alternative packaging methods may be used. No problem must
occur during the exportation of the product.
13-5 Marking
At last, production country is displayed in English.
(1) Side of reel (Marking shall be on one side)
1)Part name, 2)Part number, 3)Quantity, 4)Lot number, 5)Maker name
6) Poduction country
(2)Packaging box
1)Customer name, 2)Part name, 3)Part number, 4)Customer part number, 5)Quantity
6)Maker name, 7)Poduction country
Panasonic Electronic Devices Co., Ltd.
相关型号：
©2020 ICPDF网 联系我们和版权申明