PD10NG-1205E2:1 [PEAK]
Analog Circuit;
| 型号： | PD10NG-1205E2:1 |
| 厂家： | 
PEAK ELECTRONICS GMBH |
| 描述： | Analog Circuit |
| 文件： | 总3页 (文件大小：109K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Telefon: +49 (0)6135 931069
Telefax: +49 (0)6135 931070
www.peak-electronics.de
info@peak-electronics.de
PD10NG-XXXXE2:1 1KV ISOLATED 2W REGULATED SINGLE OUTPUT SIP8
Electrical Specifications
(Typical at + 25℃ , nominal input voltage, rated output current unless otherwise specified)
Input Specifions
Voltage range
Filter
4.5-9, 9-18, 18-36 and 36-72 VDC Wide lnput
Capacitor type
lsolation Specifications
Rated voltage
Resistance
1000 VDC
＞1 GΩ
Capacitance
68 PF
Output Specifications
Voltage accuracy
+/−2 %, typ.
Ripple and noise (at 20 MHz BW)
Short circuit protection
Line voltage regulation
Load voltage regulation
Temperature coefficient
100 mV p-p, max.
Continuous, auto restart
+/−0.2 % typ.
+/−0.5 % typ. load = 10 ~ 100%
+/−0.02 % / ℃
General Specifications
Efficiency
Switching frequency
Refer to the table
75 KHz, typ.
Environmental Specifications
Operating temperature (ambient)
Storage temperature
Humidity
− 40 ℃ to + 80 ℃
− 55 ℃ to + 125 ℃
Up to 90 %, non condensing
Free air convection
Cooling
Physical Characteristics
Dimensions SIP
21.80 x 9.20 x 11.10 mm
Case material
Non conductive black plastic
Samples of Partnumbers
PART
NO.
INPUT
VOLTAGE
(VDC)
INPUT
CURRENT
NO LOAD
(mA)
INPUT
CURRENT
FULL LOAD
(mA)
OUTPUT
VOLTAGE
(VDC)
OUTPUT
CURRENT
(max.mA)
EFFICIENCY FULL LOAD
(% TYP.)
68
72
71
73
73
73
70
75
77
78
78
76
71
74
78
79
80
78
72
77
78
80
80
78
PD10NG-053R3E2:1
PD10NG-0505E2:1
PD10NG-0509E2:1
PD10NG-0512E2:1
PD10NG-0515E2:1
PD10NG-0524E2:1
PD10NG-123R3E2:1
PD10NG-1205E2:1
PD10NG-1209E2:1
PD10NG-1212E2:1
PD10NG-1215E2:1
PD10NG-1224E2:1
PD10NG-243R3E2:1
PD10NG-2405E2:1
PD10NG-2409E2:1
PD10NG-2412E2:1
PD10NG-2415E2:1
PD10NG-2424E2:1
PD10NG-483R3E2:1
PD10NG-4805E2:1
PD10NG-4809E2:1
PD10NG-4812E2:1
PD10NG-4815E2:1
PD10NG-4824E2:1
4.5 - 9
4.5 - 9
4.5 - 9
4.5 - 9
4.5 - 9
4.5 - 9
9 - 18
9 - 18
9 - 18
9 - 18
9 - 18
41
37
38
37
37
37
24
23
22
22
22
22
12
12
12
12
11
11
8
487
455
458
452
452
452
237
219
215
212
212
217
117
111
108
105
102
106
58
3,3
5
9
12
15
24
3,3
5
606
400
222
167
133
83
606
400
222
167
133
83
606
400
222
167
133
83
606
400
222
167
133
83
9
12
15
24
3,3
5
9 - 18
18 - 36
18 - 36
18 - 36
18 - 36
18 - 36
18 - 36
36 - 72
36 - 72
36 - 72
36 - 72
36 - 72
36 - 72
9
12
15
24
3,3
5
7
7
7
7
54
53
52
52
9
12
15
24
7
53
PD10NG-XXXXE2:1 1KV ISOLATED 2W REGULATED SINGLE OUTPUT SIP8
Dimensions
21,8
PEAK
Modelcode
9,2
1
2 3
5
6
7
8
11,10
0.25± 0.05
2.0± 0.50
3.20 typ.
0.50± 0.05
3.10 typ.
2.54 typ.
0.50± 0.05
Recommended footprint details
2,54
XX.X± 0.5m/m
XX.XX± 0.25m/m
Unit : mm
1.0φ＋0.15 /－0
2,54
Derating Graph and Pinning
Pin
Connection
Single
Output
Temperature Derating Graph
Ambient Temperature C
#
1
2
3
4
5
6
7
8
−
+
V
V
Input
Input
Ctrl
2.00W
Omitted
NE
Safe Operating Area
+
−
V
V
Output
Output
CS
Control input can be left open (3)
No external connection allowed (5)
Optional external capacitor (8)
－40
0
40
80 100
PD10NG-XXXXE2:1 1KV ISOLATED 2W REGULATED SINGLE OUTPUT SIP8
External capacitance:
Pin 3 (CTRL)
These converters will work with without external
capacitors but they are necessary in order to
guarantee the full line load range. All parts have
been tested using the following recommended
values.
Control pin (ON/OFF)
Output starts at low or open and stops when high.
Voltage applied via a limiting resistor and switching
diode. The converter is in a low power mode during
the high level phase.
+ Vout
Cout
- Vout
+ Vin
Connection example
＋
＋
Converter
Cin
- Vin
1N4148
1K
MCU
Vcc-5V
CONVERTER
Cin
Cout
10uF/100V, low ESR.
100uF/35V, low ESR.
PIN 3
Pin 8 (CS)
This pin provides a connection point to the main
reservoir capacitor. Additional capacitance can
be added from this to pin 7. Any low ESR
capacitor will improve ripple and noise in some
measure. Starting values can be in the range of
100uF.
Pin 5 (NE)
This pin is used internally and must have have no external connection.
Application Notes
Pin 3: The outside control connection. This pin provides the converter output ON/OFF,
and the control common is referred to negative input.
Pin 5: This pin belongs to the secondary side. It just avoids someone to reverses the primary
and secondary.
Pin 8: Max. 1000 uF
Specification can be changed without notice.
REV: 1 / 03.2003
Copyright PEAK electronics GmbH
相关型号：
©2020 ICPDF网 联系我们和版权申明