PSD-0505ELF [PEAK]
Analog Circuit;
| 型号： | PSD-0505ELF |
| 厂家： | 
PEAK ELECTRONICS GMBH |
| 描述： | Analog Circuit |
| 文件： | 总4页 (文件大小：144K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PSD-xxxxELF
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
peak@peak-electronics.de
PSD-SERIES
ꢀ 1 Watt
ꢀ Unregulated
ꢀ Single Output
ꢀ SMD Case
Rev.04-2009
The PSD series is a family of cost effective 1 W single output DC/DC
converters. These converters are in an ultra miniature SMD 5-pin case.
Devices are encapsulated. High performance features: 1000VDC
input/output isolation, industrial standard pinout, high power density, no
heatsink required
ꢀ 1 kV DC I/O Isolation
ꢀ Low Ripple and Noise
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
10%
Capacitors
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
3%, typ.
Short Term
1.5%, max. (For Vin Change of 1%)
1.2%, max. (For Vin Change of 1%)
3.3 Vout
Others
Load Regulation (10% - 100%)
3.3 Vout 20%, max.
5 Vout
9, 12, 15, 24 Vout
15%, max.
10%, max.
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
75 mV pk-pk, max.
0.03% / °C
General Specifications
Efficiency
I/O Isolation Voltage (3 sec.)
I/O Isolation Resistance (Tested at 500 VDC)
Switching Frequency
Humidity
See Table
1000 VDC
1000 M Ohm
100 kHz, typ (5, 12 Vin); 500 kHz (24Vin)
95% rel H
Reliability Calculated MTBF (MIL-HDBK-217F) > 3500 khrs
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Epoxy (UL94V-0 rated)
~ 1.4g, max.
Environment Specifications
Operating Temperature
Storage Temperature
Cooling
Soldering
RoHS Conform
-40 to +85°C (ambient)
-55 to +125°C
Free Air Convection (10mm distance required)
Not usable for heat steam soldering
PSD-Series – PSD-xxxxELF – Single Output – SMD - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single Output
Order #
SINGLE OUTPUT
PSD-3R33R3ELF
PSD-3R305ELF
PSD-053R3ELF
PSD-0505ELF
PSD-0509ELF
PSD-0512ELF
PSD-0515ELF
PSD-1205ELF
PSD-1209ELF
PSD-1212ELF
PSD-1215ELF
PSD-243R3ELF
PSD-2405ELF
PSD-2409ELF
PSD-2412ELF
PSD-2415ELF
PSD-2424ELF
3.3
3.3
5
3.3
5
303
200
303
200
111
84
30
20
30
20
12
9
73
74
72
77
76
79
78
69
73
73
74
69
70
72
75
76
77
3.3
5
5
5
9
5
12
15
5
5
67
7
12
12
12
12
24
24
24
24
24
24
200
111
84
20
12
9
9
12
15
3.3
5
67
7
300
200
110
83
30
20
11
8
9
12
15
24
67
42
7
4
If you need other specifications, please enquire.
Notes:
PSD-Series – PSD-xxxxELF – Single Output – SMD - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
Package / Pinning / Derating
PIN CONNECTIONS
#
1
2
4
5
8
SINGLE
- Vin
+Vin
- Vout
+Vout
N.C.
Others Omitted
Reflow:
Peak.Temp 260℃
10 Sec Max
250
220℃
200
90 Sec Max
(>220℃)
150
100
50
0
Time (sec.)
PSD-Series – PSD-xxxxELF – Single Output – SMD - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
App Notes
Requirement on output load
To ensure this module can operate efficiently and reliably, during operation, the
minimum output load is not less than 10% of the full load, and that this product
should never be operated under no-load! If the actual output power is very small,
please connect a resistor with proper resistance at the output end in parallel to increase
the load.
Recommended testing circuit
If you want to further decrease the
input/output ripple, an “LC” filtering
network may be connected to the
input and output ends if the DC/DC
converter, see Figure on the right
hand side.
It should also be noted that the inductance and the frequency of the “LC” filtering
network should be staggered with the DC/DC frequency to avoid mutual interference.
However, the capacitance of the output filter capacitor must be proper. If the
capacitance is too big, a start-up problem might arise. For every channel of output,
provided the safe and reliable operation is ensured, the greatest capacitance of its
filter capacitor sees (see Table).
EXTERNAL CAPACITOR TABLE
Output Voltage Regulation and
Over-voltage
Protection Circuit
The simplest device for output voltage
regulation, over-voltage and over-
current protection is a linear voltage
regulator with overheat protection that
is connected to the input or output
end in series.
Vin
(VDC)
3.3 / 5
12
Vout
(VDC)
3.3 / 5
9
12
15
Cin (uF)
Cout (uF)
4.7
2.2
0.47
--
10
4.7
2.2
1
24
--
--
--
24
0.47
It’s not recommend to connect any external
capacitor in the application field with less
than 0.5 watt output.
Overload Protection
Under normal operating conditions, the output
circuit of these products has no protection against
over-current and short-circuits. The simplest
method is to connect a self-recovery fuse in series
at the input end or add a circuit breaker to the
circuit.
No parallel connection or plug and play.
PSD-Series – PSD-xxxxELF – Single Output – SMD - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4
相关型号：
©2020 ICPDF网 联系我们和版权申明